GBOND-ATM-MIB
The GBOND-ATM-MIB module provides SNMP management objects for configuring and monitoring ITU-T G.998.1 (G.Bond/ATM) inverse multiplexing on multi-pair bonded xDSL interfaces, specifically tracking Bonding Channel Entity (BCE) states, Signal-to-Noise Ratio (SNR) margins, and ATM layer performance metrics. This module operates in conjunction with the GBOND-MIB to enable granular fault isolation and performance analysis of the Generic Bonding Sublayer (GBS) within Central Office (CO) and Customer Premises Equipment (CPE) environments.
Imported Objects
Objects
19 total| Object Name |
|---|
gBondAtmMIBThe objects in this MIB module are used to manage the multi-pair bonded xDSL Interfaces using ATM inverse multiplexing, defined in ITU-T recommendation G.998.1 (G.Bond/ATM). This MIB module MUST be used in conjunction with GBOND-MIB module, common to all G.Bond technologies. The following references are used throughout this MIB module: [WT-159] refers to: DSL Forum Technical Report: 'Management Framework for xDSL Bonding', January 2007. Naming Conventions: BCE - Bonding Channel Entity CO - Central Office CPE - Customer Premises Equipment GBS - Generic Bonding Sublayer SNR - Signal to Noise Ratio Copyright (C) The Internet Society (2007). This version of this MIB module is part of RFC XXXX; see the RFC itself for full legal notices. MODULE-IDENTITY .1.3.6.1.2.1.211.1 |
gBondAtmObjects OBJECT IDENTIFIER .1.3.6.1.2.1.211.1.1 |
gBondAtmPort OBJECT IDENTIFIER .1.3.6.1.2.1.211.1.1.1 |
gBondAtmPortConfTableTable for Configuration of G.Bond ATM ports. Entries in this table MUST be maintained in a persistent manner SEQUENCE OF GBondAtmPortConfEntry .1.3.6.1.2.1.211.1.1.1.1 |
gBondAtmPortConfEntryAn entry in the G.Bond ATM Port Configuration table. Each entry represents an G.Bond ATM port indexed by the ifIndex. Additional configuration parameters are available via the gBondPortConfEntry of GBOND-MIB. Note that an G.Bond ATM port runs on top of a single or multiple BCE port(s), which are also indexed by ifIndex. GBondAtmPortConfEntry .1.3.6.1.2.1.211.1.1.1.1.1 |
gBondAtmUpMaxDataRateThe maximum net upstream data rate a bonding group is allowed to achieve to carry an ATM stream.If set to '9999999', this parameter is ignored.rw Unsigned32(1..1000000|9999999) UNITS "Kbps" .1.3.6.1.2.1.211.1.1.1.1.1.1 |
gBondAtmDownMaxDataRateThe maximum net downstream data rate a bonding group is allowed to achieve to carry an ATM stream.If set to '9999999', this parameter is ignored.rw Unsigned32(1..1000000|9999999) UNITS "Kbps" .1.3.6.1.2.1.211.1.1.1.1.1.2 |
gBondAtmUpDiffDelayTolerenceThe maximum upstream differential delay among member links in a bonding group.rw Unsigned32 .1.3.6.1.2.1.211.1.1.1.1.1.3 |
gBondAtmDownDiffDelayTolerenceThe maximum downstream differential delay among member links in a bonding group.rw Unsigned32 .1.3.6.1.2.1.211.1.1.1.1.1.4 |
gBondAtmPortStatusTableThis table provides overall status information of G.Bond ATM ports, complementing the generic status information from the ifTable of IF-MIB and gBondFltStatus of GBOND-MIB. Additional status information about connected BCEs is available from the relevant line MIBs This table contains live data from the equipment. As such, it is NOT persistent. SEQUENCE OF GBondAtmPortStatusEntry .1.3.6.1.2.1.211.1.1.1.2 |
gBondAtmPortStatusEntryAn entry in the G.Bond ATM port Status table. Each entry represents a G.Bond ATM port indexed by the ifIndex. Note that an G.Bond GBS port runs on top of a single or multiple BCE port(s), which are also indexed by ifIndex. GBondAtmPortStatusEntry .1.3.6.1.2.1.211.1.1.1.2.1 |
gBondAtmShowTimeThe accumulated time when a bonding group is in normal operation.ro TimeTicks UNITS "seconds" .1.3.6.1.2.1.211.1.1.1.2.1.1 |
gBondAtmUpRxCellLossCountThe total number of cells that are lost at aggregation output in the upstream direction from a bonding group for the accumulation interval.ro Counter32 .1.3.6.1.2.1.211.1.1.1.2.1.2 |
gBondAtmDownRxCellLossCountThe total number of cells that are lost at aggregation output in the downstream direction from a bonding group for the accumulation interval.ro Counter32 .1.3.6.1.2.1.211.1.1.1.2.1.3 |
gBondAtmConformance OBJECT IDENTIFIER .1.3.6.1.2.1.211.1.2 |
gBondAtmGroups OBJECT IDENTIFIER .1.3.6.1.2.1.211.1.2.1 |
gBondAtmBasicGroupA collection of objects representing management information for G.Bond ATM ports. Unknown .1.3.6.1.2.1.211.1.2.1.1 |
gBondAtmCompliances OBJECT IDENTIFIER .1.3.6.1.2.1.211.1.2.2 |
gBondAtmComplianceThe compliance statement for G.Bond ATM interfaces. Compliance with the following external compliance statements is REQUIRED: MIB Module Compliance Statement ---------- -------------------- IF-MIB ifCompliance3 GBOND-MIB gBondCompliance Unknown .1.3.6.1.2.1.211.1.2.2.1 |
More MIBs from Default
Browse all DefaultMIBs →SNMP MIB module
The AVAYA-WLAN-MIB provides SNMP-based management and monitoring capabilities for Avaya wireless LAN infrastructure, enabling the collection of performance metrics such as access point status, client association counts, signal strength, and radio interface statistics. This module facilitates the tracking of WLAN-specific events and configuration parameters to support network availability and troubleshooting within Avaya wireless deployments.
The VMWARE-NSX-MIB enables SNMP-based monitoring and management of VMware NSX-T Data Center virtual network infrastructure, exposing metrics for logical switches, routers, distributed firewalls, and overlay tunnel states. It facilitates the tracking of Layer 2 through Layer 7 service instances, including access control lists, Quality of Service policies, and virtual network topology changes within the software-defined networking environment.
Standard SNMP MIB module defining data structures for 923switch.m.
Standard SNMP MIB module defining data structures for CTATX-MIB.
SNMP MIB module