FRDTE-OPT-MIB
Detailed view of the defined objects, syntax rules, and hierarchical paths.
136
Objects
Active
Status
2
Dependencies
Imported Objects
Objects
136 total| Object Name |
|---|
codex OBJECT IDENTIFIER .1.3.6.1.4.1.449 |
RFC1155-SMI Unknown .1.3.6.1.4.1.449 |
cdxProductSpecific OBJECT IDENTIFIER .1.3.6.1.4.1.449.2 |
cdx6500 OBJECT IDENTIFIER .1.3.6.1.4.1.449.2.1 |
cdx6500Configuration OBJECT IDENTIFIER .1.3.6.1.4.1.449.2.1.2 |
cdx6500CfgProtocolGroup OBJECT IDENTIFIER .1.3.6.1.4.1.449.2.1.2.1 |
cdx6500PCTPortProtocolGroup OBJECT IDENTIFIER .1.3.6.1.4.1.449.2.1.2.1.1 |
cdx6500PCTFRDTEPortTableAll of the configuration parameters relevant
to the Frame Relay DTE Port table. SEQUENCE OF Cdx6500PCTFRDTEPortEntry .1.3.6.1.4.1.449.2.1.2.1.1.5 |
cdx6500PCTFRDTEPortEntryA row of FRI Port configuration parameters. Cdx6500PCTFRDTEPortEntry .1.3.6.1.4.1.449.2.1.2.1.1.5.1 |
cdx6500frdtepCfgPortNumSpecifies the Port number for the Frame Relay
Interface port you are selecting.ro INTEGER .1.3.6.1.4.1.449.2.1.2.1.1.5.1.1 |
cdx6500frdtepConnectionTypeSpecify the control signal handshake and clocking required
for a connection to be made to this port:
simp - simple, no control signals required
dtr - dedicated, require the data terminal ready signal (DTR)
simpb - simple, no control signals required for data
transmission and reception. By default output
leads will be low.
nc - Skipped during configuration.rw Enumeration .1.3.6.1.4.1.449.2.1.2.1.1.5.1.2 |
cdx6500frdtepClockSourceint - internal clock source
ext - external clock source
extint - Internal receive and external transmit
clock source (DCE only).
extlp - external receive and loopback transmit
clock source (DTE only).
EXTLP must be configured in conjunction
with EXTINT.
nc - Skipped during configuration.rw Enumeration .1.3.6.1.4.1.449.2.1.2.1.1.5.1.3 |
cdx6500frdtepClockSpeedThis is the speed of the port in bits per second,
when using internal clocking. The highest available
speed is dependent on the card type,and on the interface type.rw INTEGER .1.3.6.1.4.1.449.2.1.2.1.1.5.1.4 |
cdx6500frdtepMaxStationsThis is the highest station number to be configured on this
FRI port.
It is used to limit the configuration of stations.rodeprecated INTEGER .1.3.6.1.4.1.449.2.1.2.1.1.5.1.5 |
cdx6500frdtepFrameSeqCountingPort uses normal or extended frame sequence numbering:
normal - normal sequencing (modulo 8)
ext - extended sequencing (modulo 128)
nc - Skipped during configuration.
All stations on this port will be set to this value.ro Enumeration .1.3.6.1.4.1.449.2.1.2.1.1.5.1.6 |
cdx6500frdtepPktSeqCountingPort uses normal or extended packet level sequence numbers
normal - normal sequencing (Modulo 8)
ext - extended sequencing (Modulo 128)
nc - Skipped during configuration.
This parameter must be set to the same value
at both this FRI port and the remote FRI port.
All stations on this port will be set to this value.rw Enumeration .1.3.6.1.4.1.449.2.1.2.1.1.5.1.7 |
cdx6500frdtepCtrlProtocolWhether ANSI T1.617 Annex D or LMI Support is enabled
none - None is enabled.
annexD - Annex D is enabled
lmi - LMI is enabled.
annexA - Annex A is enabled.
auto - Auto-learn the Network control protocol type
nc - Skipped during configuration.rw Enumeration .1.3.6.1.4.1.449.2.1.2.1.1.5.1.8 |
cdx6500frdtepT391This parameter is the Link Integrity Verification
Timer polling period. The FRI port sends status enquiry
messages to network every T391/nT1 seconds.rw INTEGER .1.3.6.1.4.1.449.2.1.2.1.1.5.1.9 |
cdx6500frdtepT392This parameter is the polling Cycle Verification
Timer period. The FRI port expects status enquiry messages
every T392/nT2 seconds. This parameter must be set to a
value greater than N391/nT1, and applies only in
bi-directional mode.ro INTEGER .1.3.6.1.4.1.449.2.1.2.1.1.5.1.10 |
cdx6500frdtepN391Full Status polling cycle. FRI port sends Full status
enquiry messages to network every nN1 polls.rw INTEGER .1.3.6.1.4.1.449.2.1.2.1.1.5.1.12 |
cdx6500frdtepN392Error inactivity threshold. Number of errors during NN3
events that cause the station to be declared inactive.
Should be less than or equal to nN3.ro INTEGER .1.3.6.1.4.1.449.2.1.2.1.1.5.1.13 |
cdx6500frdtepN393Monitored events count for measuring nN3. nN2 errors during
nN3 events will cause the station to be declared inactive.
Should be greater than nN3.rw INTEGER .1.3.6.1.4.1.449.2.1.2.1.1.5.1.14 |
cdx6500frdtepNT1This parameter is the Link Integrity Verification
Timer polling period. The FRI port sends status enquiry
messages to network every T391/nT1 seconds.rw INTEGER .1.3.6.1.4.1.449.2.1.2.1.1.5.1.15 |
cdx6500frdtepNT2This parameter is the polling Cycle Verification
Timer period. The FRI port expects status enquiry messages
every T392/nT2 seconds. This parameter must be set to a
value greater than N391/nT1, and applies only in
bi-directional mode.ro INTEGER .1.3.6.1.4.1.449.2.1.2.1.1.5.1.16 |
cdx6500frdtepNN1Full Status polling cycle. FRI port sends Full status
enquiry messages to network every nN1 polls.ro INTEGER .1.3.6.1.4.1.449.2.1.2.1.1.5.1.17 |
cdx6500frdtepNN2Error inactivity threshold. Number of errors during NN3
events that cause the station to be declared inactive.
Should be less than or equal to nN3.rw INTEGER .1.3.6.1.4.1.449.2.1.2.1.1.5.1.18 |
cdx6500frdtepNN3Monitored events count for measuring nN3. nN2 errors during
nN3 events will cause the station to be declared inactive.
Should be greater than nN3.ro INTEGER .1.3.6.1.4.1.449.2.1.2.1.1.5.1.19 |
cdx6500frdtepHighPriorityStnThis parameter specifies a station who's PVC status has
priority over all other stations when FRI same port back
up is enabled. When the network reports this DLCI inactive,
an alternate connection over a backup link is attempted.rw INTEGER .1.3.6.1.4.1.449.2.1.2.1.1.5.1.20 |
cdx6500frdtepMaxVoiceBWBitsPerSecThis parameter limits the bandwidth, in bits per sec
(including overhead), for voice traffic passing through this
frame relay port. A zero value disables any voice passing
through this port.rw INTEGER .1.3.6.1.4.1.449.2.1.2.1.1.5.1.21 |
cdx6500frdtepSegSizeVoicePresentData packets to be segmented into this maximum frame size when
voice is active on this port.
segSize32 - 32 byte segments
segSize64 - 64 byte segments
segSize128 - 128 byte segments
segSize256 - 256 byte segments
segSize512 - 512 byte segments
segSize1024 - 1024 byte segments
nc - Skipped during configuration.rw Enumeration .1.3.6.1.4.1.449.2.1.2.1.1.5.1.22 |
cdx6500frdtepSegSizeVoiceNotPresentData packets to be segmented into this maximum frame size when
voice is not active on this port.
segSize32 - 32 byte segments
segSize64 - 64 byte segments
segSize128 - 128 byte segments
segSize256 - 256 byte segments
segSize512 - 512 byte segments
segSize1024 - 1024 byte segments
segSize2048 - 2048 byte segments
segSize4096 - 4096 byte segments
disable - segment size is 32768 bytes
nc - Skipped during configuration.rw Enumeration .1.3.6.1.4.1.449.2.1.2.1.1.5.1.23 |
cdx6500frdtepInvertTXClockThis parameter specifies whether the phase of the transmit
clock should be inverted. Note: This parameter is primarily
for X.21 electrical interfaces.
no - Don't invert.
yes - Invert.rw Enumeration .1.3.6.1.4.1.449.2.1.2.1.1.5.1.24 |
cdx6500frdtepControlProtocolOptionsThese options control the PVC management protocol
none - No option selected
async - The port will send/receive asynchronous
A-bit if it is performing Network side
protocol functionality
nbit - The port will send and accept N-bit messages
dbit - The port will send and accept D-bit messages
This forces ASYNC to be specified (dbit+async)rw DisplayString .1.3.6.1.4.1.449.2.1.2.1.1.5.1.25 |
cdx6500frdtepDiscardControlOptionsThis parameter controls the discard frame options
none - No option selected
debit - DE marked frames are discarded before
non-DE framesrw Enumeration .1.3.6.1.4.1.449.2.1.2.1.1.5.1.26 |
cdx6500frdtepElectricalInterfaceTypeSpecify the Electrical Interface Type:
V.24 - V.24 Electrical Interface Type
V.35 - V.35 Electrical Interface Type
V.36 - V.36 Electrical Interface Type
X.21 - X.21 Electrical Interface Type
NONE - Electrically disabledrw Enumeration .1.3.6.1.4.1.449.2.1.2.1.1.5.1.27 |
cdx6500frdtepV24ElectricalInterfaceOptionSpecify the Pin 22 option:
RI - V.24 uses Pin 22 for Ring Indicator output signal
TM - V.24 uses Pin 22 for Test Mode input signalrw Enumeration .1.3.6.1.4.1.449.2.1.2.1.1.5.1.28 |
cdx6500frdtepHighSpeedElectricalInterfaceOptionSpecify the cable type:
NONE - V.35/V.36/X.21 DCE with straight through cable
XOVER - V.35/V.36/X.21 DCE with crossover adapter cablerw Enumeration .1.3.6.1.4.1.449.2.1.2.1.1.5.1.29 |
cdx6500PCTStationProtocolGroup OBJECT IDENTIFIER .1.3.6.1.4.1.449.2.1.2.1.3 |
cdx6500SPCTFRDTEStationTableAll of the configuration parameters relevant to the Frame
Relay DTE Station table. SEQUENCE OF Cdx6500SPCTFRDTEStationEntry .1.3.6.1.4.1.449.2.1.2.1.3.2 |
cdx6500SPCTFRDTEStationEntryA row of Frame Realy DTE station configuration parameters. Cdx6500SPCTFRDTEStationEntry .1.3.6.1.4.1.449.2.1.2.1.3.2.1 |
cdx6500frdtesCfgPortNumFR DTE Port number.ro INTEGER .1.3.6.1.4.1.449.2.1.2.1.3.2.1.1 |
cdx6500frdtesCfgDLCIThe Data Link Connection Identifier (dlci) is the unique
identifier for the station on the FRI Port. Its valid range
is 16 - 1007. It must match the DLCI configured on the FR
Networking Node.rw INTEGER .1.3.6.1.4.1.449.2.1.2.1.3.2.1.2 |
cdx6500frdtesStationTypeIdentifies the type of station being configured.
annexG - This station uses X.25 signaling for layer 3
bypass - This station type bypasses layer 3. There is
no signaling for SVC's on this station.
voiceRelay - Not used in the current version.rw Enumeration .1.3.6.1.4.1.449.2.1.2.1.3.2.1.3 |
cdx6500frdtesCommInfoRateThis parameter (CIR) specifies the rate (in bits-per-second)
that the Frame Relay network agrees to transfer information
under congested conditions for the FRI Station.
This value is used to throttle data on the FRI station for
congestion control purposes. The CIR cannot be greater than
the link speed.rw INTEGER .1.3.6.1.4.1.449.2.1.2.1.3.2.1.4 |
cdx6500frdtesCommBurstSizeThis parameter (BC) specifies the maximum amount of data (in
bits) that the Frame Relay network agrees to transfer over a
time interval T = Committed Burst Size / Committed Information
Rate. Must be > 1/20th of the Committed Information Rate.
This is used for congestion control purposes.rw INTEGER .1.3.6.1.4.1.449.2.1.2.1.3.2.1.5 |
cdx6500frdtesTransDelayThis parameter is the expected one-way delay through the
network. This is specified in milliseconds.rw INTEGER .1.3.6.1.4.1.449.2.1.2.1.3.2.1.6 |
cdx6500frdtesControlledModeThis parameter controls the method of congestion control:
normal - congestion control is normal
disable - never enter Congested State (CTRL)
congested - never enter a Non-Congested State (UCTRL)
limit - congestion control is normal but limits the
data rate to no lower than CIR.
nc - Skipped during configurationrw Enumeration .1.3.6.1.4.1.449.2.1.2.1.3.2.1.7 |
cdx6500frdtesLinkAddressThe logical link address must be set to complementary values
in this FRI station and its corresponding remote FRI station:
dte - station to have logical DTE address (A)
dce - station to have logical DCE address (B)
nc - Skipped during configuration.rw Enumeration .1.3.6.1.4.1.449.2.1.2.1.3.2.1.8 |
cdx6500frdtesPVCChannelsNumber of logical channels used for Permanent Virtual Circuits.
The total number of PVC and SVC channels on a station (logical
link) should be kept as small as possible and consistent with
needs. PVC connections must be configured in the PVC Table.rw INTEGER .1.3.6.1.4.1.449.2.1.2.1.3.2.1.9 |
cdx6500frdtesStartingPVCThis is the starting logical channel number for the Permanent
Virtual Circuits on this FRI station. Not used if the number
of PVCs = 0.rw INTEGER .1.3.6.1.4.1.449.2.1.2.1.3.2.1.10 |
cdx6500frdtesSVCChannelsNumber of logical channels used in Switched Virtual Circuits.
The total number of PVC and SVC channels on a station (logical
link) should be kept as small as possible and consistent with
needs.rw INTEGER .1.3.6.1.4.1.449.2.1.2.1.3.2.1.11 |
cdx6500frdtesStartingSVCThis is the starting logical channel number for the Switched
Virtual Circuits on this station (logical link). Not used if
the number of SVCs = 0.rw INTEGER .1.3.6.1.4.1.449.2.1.2.1.3.2.1.12 |
cdx6500frdtesInitialFrameSpecify the initial frame required by other end for (logical)
link startup:
none - do nothing (other end initiates link-up)
sabm - send SABM
disc - send DISC, then SABM
nc - Skipped during configurationrw Enumeration .1.3.6.1.4.1.449.2.1.2.1.3.2.1.13 |
cdx6500frdtesRetryTimerT1 link retry timer value in tenths of a second (e.g. 30 = 3.0
seconds).rw INTEGER .1.3.6.1.4.1.449.2.1.2.1.3.2.1.14 |
cdx6500frdtesPollTimerThis sets the time an idle link is probed for assurance of
connection to the remote FRI station.
0 - disable the timer
X - X is in tenths of a second (e.g. 40 = 4.0 seconds) and
must be set greater than T1.rw INTEGER .1.3.6.1.4.1.449.2.1.2.1.3.2.1.15 |
cdx6500frdtesTriesThe maximum number of attempts allowed to complete a
transmission.rw INTEGER .1.3.6.1.4.1.449.2.1.2.1.3.2.1.16 |
cdx6500frdtesFrameWinSizeFrame level window size must be set to the same value
at both this FRI station and the remote FRI station.rw INTEGER .1.3.6.1.4.1.449.2.1.2.1.3.2.1.17 |
cdx6500frdtesPacketWinSizePacket level window size must be set to the same value
at both this FRI station and the remote FRI station.rw INTEGER .1.3.6.1.4.1.449.2.1.2.1.3.2.1.18 |
cdx6500frdtesMaxPacketSizeThis is the maximum X.25 packet size used on the station
(logical link).
For proper operation, this must be set to the same value
at both this FRI station and the remote FRI station.
nc - Skipped during configuration.rw Enumeration .1.3.6.1.4.1.449.2.1.2.1.3.2.1.19 |
cdx6500frdtesUpperQueueThis is the maximum number of data packets a channel on this
station (logical link) will queue for transmission before
invoking flow control to the attached channelrw INTEGER .1.3.6.1.4.1.449.2.1.2.1.3.2.1.20 |
cdx6500frdtesLowerQueueThis is the number of data packets a channel on this FRI
station will have queued for transmission when it releases
flow control to the attached channelrw INTEGER .1.3.6.1.4.1.449.2.1.2.1.3.2.1.21 |
cdx6500frdtesRestartTimerRestart-Request timeout timer in seconds. If timer expires on
this FRI station, the Restart request is sent again.rw INTEGER .1.3.6.1.4.1.449.2.1.2.1.3.2.1.22 |
cdx6500frdtesResetTimerReset-Request timeout timer in seconds. If timer expires on
this FRI station, the Reset request is sent again.rw INTEGER .1.3.6.1.4.1.449.2.1.2.1.3.2.1.23 |
cdx6500frdtesCallTimerCall-Request timeout timer in seconds. If timer expires on
this FRI station, the call is cleared.rw INTEGER .1.3.6.1.4.1.449.2.1.2.1.3.2.1.24 |
cdx6500frdtesClearTimerClear-Request timeout timer in seconds. If timer expires on
this FRI station, the Clear request is sent again.rw INTEGER .1.3.6.1.4.1.449.2.1.2.1.3.2.1.25 |
cdx6500frdtesX25OptionsSelect X.25 options on this station (logical link) as follows:
NONE - no option specified
CUG - check closed user group; otherwise, CUG passes
transparently
CAUSE - pass cause, diagnostic, code in outbound packets
HOLD - hold calls over link restart
INL - inter-node link. Link goes to another 6500 device
DELAY - Enable Delay and Path Trace on this link (link must be
connected to Rel. 4.xx node)
Any combination of above specified by summing
(e.g. CUG+CAUSE+. . .).
NOTE: Please use cdx6500frdtesStnX25Options, which has been
added to replace this object.rodeprecated INTEGER .1.3.6.1.4.1.449.2.1.2.1.3.2.1.26 |
cdx6500frdtesRCDestinationAll calls entering this station will be routed to the
destination specified in this parameter, irrespective of
route selection table entries. For example, to route all
calls to X.25 port 3, use X25-3.
To route calls to FRI port 2, station 4, use FRI-2S4. Blank
this field to disable this function.rw DisplayString .1.3.6.1.4.1.449.2.1.2.1.3.2.1.27 |
cdx6500frdtesCUGThe station may be a member of up to 8 different Closed User
Groups (CUGs). Each CUG membership must be a two digit number
and separated by a comma.
(e.g. 12,34,56,09,02,03 ).
Two hyphens following each oher indicates no CUG Membership
00-99 - CUG Membershiprw DisplayString .1.3.6.1.4.1.449.2.1.2.1.3.2.1.28 |
cdx6500frdtesBillingRecordsThis controls whether billing (accounting) records will be
created for calls on this FRI station.
off - Billing records will not be created.
on - Billing records will be created.
nc - Skipped during configuration.rw Enumeration .1.3.6.1.4.1.449.2.1.2.1.3.2.1.29 |
cdx6500frdtesCfgStationNumThe number of the logical link on the line.
This is the value of Sxx for routing purposes.ro INTEGER .1.3.6.1.4.1.449.2.1.2.1.3.2.1.30 |
cdx6500frdtesStnX25OptionsSelect X.25 options on this station (logical link) as follows:
NONE - no option specified
CUG - check closed user group; otherwise, CUG passes
transparently
CAUSE - pass cause, diagnostic, code in outbound packets
HOLD - hold calls over link restart
INL - inter-node link. Link goes to another 6500 device
DELAY - Enable Delay and Path Trace on this link (link must be
connected to Rel. 4.xx node)
Any combination of above specified by summing
(e.g. CUG+CAUSE+. . .).
NOTE: This object has been added to replace
cdx6500frdtesX25Options.rw DisplayString .1.3.6.1.4.1.449.2.1.2.1.3.2.1.31 |
cdx6500frdtesStnFrameSegmenterDetermine if this station will support the Frame Segmenter
Header.The Frame Segmenter should be enabled if the frame
relay port is configured to pass voice traffic.
disabled - Frame Segmenter disabled.
enabled - Frame Segmenter enabled.
nc - Skipped during configuration.rw Enumeration .1.3.6.1.4.1.449.2.1.2.1.3.2.1.32 |
cdx6500frdtesStnVoiceSVCChannelsNumber of logical voice channels used in Switched Virtual
Circuits.The total number of voice and data channels on a
station (logical link) should be kept as small as possible
and consistent with needs.rw INTEGER .1.3.6.1.4.1.449.2.1.2.1.3.2.1.33 |
cdx6500frdtesStnVoiceCongCtrlModeThis parameter controls the method of voice congestion
control:
enabled - Station is forced into congestion when voice
calls are detected.
disabled - Station operates normally
Use this parameter in voice applications, when the frame
relay network can have more than 140ms of data buffered.
One typical application is asymmetrical speeds. When this
parameter is enabled, and voice is detected, delta T is
forced to 50 ms and the BC is forced to 1/20 CIR.rw Enumeration .1.3.6.1.4.1.449.2.1.2.1.3.2.1.34 |
cdx6500frdtesStnPeakUtilizationThe monitoring interval size specifies the time period
to use when monitoring peak data link/CIR (Committed
Information Rate) utilization.
0 - Disables this monitoring feature.
1 to 240 - The number of 64 second increments to use for the
monitoring interval time period.
For example: a value of 30 specifies a time duration
equal to 30 * 64 seconds = 1920 seconds or 32 minutes.rw INTEGER .1.3.6.1.4.1.449.2.1.2.1.3.2.1.35 |
cdx6500frdtesStnMaxInboundQueueThis specifies the maximum number of frames from the
network which may be queued in a BYPASS station. A
smaller value may ve choosen for applications which
experience objectable delays, if due to excessive
growth of the BYPASS inbound queue.rw INTEGER .1.3.6.1.4.1.449.2.1.2.1.3.2.1.36 |
cdx6500frdtesStnAnnexGRateReductionThis parameter determines whether Annex G stations will
invoke implicit congestion control when a link error is
detected, reducing their transmitted information rate
to 1/4 CIR. The rate will be gradually increased in the
normal way as non-BECN frames are received.rw Enumeration .1.3.6.1.4.1.449.2.1.2.1.3.2.1.37 |
cdx6500Statistics OBJECT IDENTIFIER .1.3.6.1.4.1.449.2.1.3 |
cdx6500StatProtocolGroup OBJECT IDENTIFIER .1.3.6.1.4.1.449.2.1.3.1 |
cdx6500PSTPortProtocolGroup OBJECT IDENTIFIER .1.3.6.1.4.1.449.2.1.3.1.1 |
cdx6500PPSTFRDTEPortTableAll of the statistics parameters relevant
to the Frame Relay DTE Port table. SEQUENCE OF Cdx6500PPSTFRDTEPortEntry .1.3.6.1.4.1.449.2.1.3.1.1.5 |
cdx6500PPSTFRDTEPortEntryA row of Frame Relay DTE Port statistics parameters. Cdx6500PPSTFRDTEPortEntry .1.3.6.1.4.1.449.2.1.3.1.1.5.1 |
cdx6500frdtepStatsPortNumSpecifies a specific port in the network diagram.ro INTEGER .1.3.6.1.4.1.449.2.1.3.1.1.5.1.1 |
cdx6500frdtepPortStatusSpecifies the current port status.
disabled - Port has been disabled.
enabled - Port is operational.
busyOut - Port has been busied out.
up - Port is operational.
down - Port is down.
na - Value not Available.ro Enumeration .1.3.6.1.4.1.449.2.1.3.1.1.5.1.2 |
cdx6500frdtepPortSpeedMessage transmition speed in bps.ro INTEGER .1.3.6.1.4.1.449.2.1.3.1.1.5.1.3 |
cdx6500frdtepUtilizationInFactor determined by comparison of volume (characters per
second) of data and clock rate for a specific port.ro INTEGER .1.3.6.1.4.1.449.2.1.3.1.1.5.1.4 |
cdx6500frdtepUtilizationOutFactor determined by comparison of volume (characters per
second) of data and clock rate for a specific port.ro INTEGER .1.3.6.1.4.1.449.2.1.3.1.1.5.1.5 |
cdx6500frdtepCharInTotalNumber of characters received since last boot or statistics
reset.ro Counter .1.3.6.1.4.1.449.2.1.3.1.1.5.1.6 |
cdx6500frdtepCharOutTotalNumber of characters transmitted since last boot or statistics
reset.ro Counter .1.3.6.1.4.1.449.2.1.3.1.1.5.1.7 |
cdx6500frdtepCharsInPerSecAverage number of characters received per second.ro INTEGER .1.3.6.1.4.1.449.2.1.3.1.1.5.1.8 |
cdx6500frdtepCharsOutPerSecAverage number of characters transmitted per second.ro INTEGER .1.3.6.1.4.1.449.2.1.3.1.1.5.1.9 |
cdx6500frdtepFrameInTotalNumber of frames received since last boot or statistics reset.ro Counter .1.3.6.1.4.1.449.2.1.3.1.1.5.1.10 |
cdx6500frdtepFrameOutTotalNumber of frames transmitted since last boot or statistics
reset.ro Counter .1.3.6.1.4.1.449.2.1.3.1.1.5.1.11 |
cdx6500frdtepFramesInPerSecAverage number of frames received per second.ro INTEGER .1.3.6.1.4.1.449.2.1.3.1.1.5.1.12 |
cdx6500frdtepFramesOutPerSecAverage number of frames transmitted per second.ro INTEGER .1.3.6.1.4.1.449.2.1.3.1.1.5.1.13 |
cdx6500frdtepOverrunErrorsAn input buffer overflowed and characters were discarded.ro Counter16 .1.3.6.1.4.1.449.2.1.3.1.1.5.1.14 |
cdx6500frdtepUnderrunErrorsNumber of errors detected since last node boot or reset of
statistics.ro Counter16 .1.3.6.1.4.1.449.2.1.3.1.1.5.1.15 |
cdx6500frdtepCRCErrorsNumber of errors detected by Cyclic Redundancy Check since
last node boot reset of statistics.ro Counter16 .1.3.6.1.4.1.449.2.1.3.1.1.5.1.16 |
cdx6500PSTStationProtocolGroup OBJECT IDENTIFIER .1.3.6.1.4.1.449.2.1.3.1.3 |
cdx6500SPSTFRDTEStationTableAll of the statistics parameters relevant
to the Frame Relay DTE Station (DLCI) table. SEQUENCE OF Cdx6500SPSTFRDTEStationEntry .1.3.6.1.4.1.449.2.1.3.1.3.2 |
cdx6500SPSTFRDTEStationEntryA row of Frame Relay DTE station (DLCI)
Statistics parameters. Cdx6500SPSTFRDTEStationEntry .1.3.6.1.4.1.449.2.1.3.1.3.2.1 |
cdx6500frdtesStatsPortNumSpecifies a specific port in the network diagram.ro INTEGER .1.3.6.1.4.1.449.2.1.3.1.3.2.1.1 |
cdx6500frdtesStatsDLCIData Link Connection Identifier is the unique identifier for
the station on the FRI port and must match the DLCI configured
on the Frame Relay networking node.ro INTEGER .1.3.6.1.4.1.449.2.1.3.1.3.2.1.2 |
cdx6500frdtesUtilizationInIndicates the quantity of user bytes sent down the link
expressed as a percentage of the maximum number of bytes that
could have been sent.ro INTEGER .1.3.6.1.4.1.449.2.1.3.1.3.2.1.3 |
cdx6500frdtesUtilizationOutIndicates the quantity of user bytes sent down the link
expressed as a percentage of the maximum number of bytes that
could have been sent.ro INTEGER .1.3.6.1.4.1.449.2.1.3.1.3.2.1.4 |
cdx6500frdtesMaxSVCCountMaximum number of SVCs available in the network.ro INTEGER .1.3.6.1.4.1.449.2.1.3.1.3.2.1.5 |
cdx6500frdtesCurrentSVCCountCurrent number of SVCs currently in use.ro INTEGER .1.3.6.1.4.1.449.2.1.3.1.3.2.1.6 |
cdx6500frdtesCharInTotalNumber of characters received since last node boot or
statistics reset.ro Counter .1.3.6.1.4.1.449.2.1.3.1.3.2.1.7 |
cdx6500frdtesCharOutTotalNumber of characters transmitted since last node boot or
statistics reset.ro Counter .1.3.6.1.4.1.449.2.1.3.1.3.2.1.8 |
cdx6500frdtesCharsInPerSecAverage number of characters received per second.ro INTEGER .1.3.6.1.4.1.449.2.1.3.1.3.2.1.9 |
cdx6500frdtesCharsOutPerSecAverage number of characters transmitted per second.ro INTEGER .1.3.6.1.4.1.449.2.1.3.1.3.2.1.10 |
cdx6500frdtesPktInTotalNumber of packets received since last node boot or statistics
reset.ro Counter .1.3.6.1.4.1.449.2.1.3.1.3.2.1.11 |
cdx6500frdtesPktOutTotalNumber of packets transmitted since last node boot or
statistics reset.ro Counter .1.3.6.1.4.1.449.2.1.3.1.3.2.1.12 |
cdx6500frdtesPktsInPerSecAverage number of packets received per second.ro INTEGER .1.3.6.1.4.1.449.2.1.3.1.3.2.1.13 |
cdx6500frdtesPktsOutPerSecAverage number of packets transmitted per second.ro INTEGER .1.3.6.1.4.1.449.2.1.3.1.3.2.1.14 |
cdx6500frdtesPacketsQueuedCurrent number of packets buffered since last node boot or
statistics reset.ro INTEGER .1.3.6.1.4.1.449.2.1.3.1.3.2.1.15 |
cdx6500frdtesFrameInTotalNumber of frames received since last node boot or statistics
reset.ro Counter .1.3.6.1.4.1.449.2.1.3.1.3.2.1.16 |
cdx6500frdtesFrameOutTotalNumber of frames transmitted since last node boot or
statistics reset.ro Counter .1.3.6.1.4.1.449.2.1.3.1.3.2.1.17 |
cdx6500frdtesFramesInPerSecAverage number of frames received per second.ro INTEGER .1.3.6.1.4.1.449.2.1.3.1.3.2.1.18 |
cdx6500frdtesFramesOutPerSecAverage number of frames transmitted per second.ro INTEGER .1.3.6.1.4.1.449.2.1.3.1.3.2.1.19 |
cdx6500frdtesInfoFramesInData received since last node boot or statistics reset.ro Counter .1.3.6.1.4.1.449.2.1.3.1.3.2.1.20 |
cdx6500frdtesInfoFramesOutData transmitted since last node boot or statistics reset.ro Counter .1.3.6.1.4.1.449.2.1.3.1.3.2.1.21 |
cdx6500frdtesRNRFramesInUsed by the DTE or the network to request that the data flow
be stopped on a particular virtual circuit.ro Counter .1.3.6.1.4.1.449.2.1.3.1.3.2.1.22 |
cdx6500frdtesRNRFramesOutUsed by the DTE or the network to request that the data flow
be stopped on a particular virtual circuit.ro Counter .1.3.6.1.4.1.449.2.1.3.1.3.2.1.23 |
cdx6500frdtesRRFramesInUsed to clear the RNR request.ro Counter .1.3.6.1.4.1.449.2.1.3.1.3.2.1.24 |
cdx6500frdtesRRFramesOutUsed to clear the RNR request.ro Counter .1.3.6.1.4.1.449.2.1.3.1.3.2.1.25 |
cdx6500frdtesREJFramesInA REJ transmitted by a receiver requests retransmission of a
frame, due to detection of a transmission or frame sequence
error.ro Counter .1.3.6.1.4.1.449.2.1.3.1.3.2.1.26 |
cdx6500frdtesREJFramesOutA REJ transmitted by a receiver requests retransmission of a
frame, due to detection of a transmission or frame sequence
error.ro Counter .1.3.6.1.4.1.449.2.1.3.1.3.2.1.27 |
cdx6500frdtesDataPktsInA packet containing user information.ro Counter .1.3.6.1.4.1.449.2.1.3.1.3.2.1.28 |
cdx6500frdtesDataPktsOutA packet containing user information.ro Counter .1.3.6.1.4.1.449.2.1.3.1.3.2.1.29 |
cdx6500frdtesResetStatsResets the specified Frame Relay station statistics.
reset - Reset station statistics.
noReset - Do not reset station statistics.rw Enumeration .1.3.6.1.4.1.449.2.1.3.1.3.2.1.30 |
cdx6500frdtesBootBoots the specified Frame Relay station.
boot - Boot station.
noBoot - Do not boot station.rw Enumeration .1.3.6.1.4.1.449.2.1.3.1.3.2.1.31 |
cdx6500frdtesDisableDisables the specified Frame Relay station.
disable - Disable station.
noDisable - Do not disable station.rw Enumeration .1.3.6.1.4.1.449.2.1.3.1.3.2.1.32 |
cdx6500frdtesEnableEnables the specified Frame Relay station.
enable - Enable station.
noEnable - Do not enable station.rw Enumeration .1.3.6.1.4.1.449.2.1.3.1.3.2.1.33 |
cdx6500frdtesStatsStationNumberThe number of the FRI Station.ro INTEGER .1.3.6.1.4.1.449.2.1.3.1.3.2.1.34 |
cdx6500Controls OBJECT IDENTIFIER .1.3.6.1.4.1.449.2.1.4 |