FORCE10-BGP4-V2-MIB
AI MIB Summary
The FORCE10-BGP4-V2-MIB enables monitoring and management of BGP4 protocol states, neighbor relationships, and routing table statistics on Dell Force10 networking hardware. It provides specific access to BGP session counters, route attributes, and peer state transitions for troubleshooting and policy enforcement within the network infrastructure.
This MIB module defines management objects for the Border Gateway Protocol, Version 4.
Main OID:
f10BgpM2.1.3.6.1.4.1.6027.20.1
270
Objects
Active
Status
6
Dependencies
Imported Objects
Objects
270 total| Object Name |
|---|
f10BgpM2This MIB module defines management objects for the Border Gateway Protocol, Version 4. MODULE-IDENTITY .1.3.6.1.4.1.6027.20.1 |
f10BgpM2BaseScalars OBJECT IDENTIFIER .1.3.6.1.4.1.6027.20.1.1 |
f10BgpM2BaseNotifications OBJECT IDENTIFIER .1.3.6.1.4.1.6027.20.1.1.0 |
f10BgpM2EstablishedThe BGP Established event is generated when the BGP FSM enters the ESTABLISHED state. NOTIFICATION-TYPE .1.3.6.1.4.1.6027.20.1.1.0.1 |
f10BgpM2BackwardTransitionThe BGPBackwardTransition Event is generated when the BGP FSM moves from a higher numbered state to a lower numbered state. NOTIFICATION-TYPE .1.3.6.1.4.1.6027.20.1.1.0.2 |
f10BgpM2Version OBJECT IDENTIFIER .1.3.6.1.4.1.6027.20.1.1.1 |
f10BgpM2VersionTableTable of supported BGP versions. SEQUENCE OF F10BgpM2VersionEntry .1.3.6.1.4.1.6027.20.1.1.1.1 |
f10BgpM2VersionEntryEntry containing data on a given supported version of the Border Gateway Protocol and the level of support provided. It is expected that any agent implementation supporting this MIB module will report support for Version 4 of the Border Gateway Protocol at the very minimum. F10BgpM2VersionEntry .1.3.6.1.4.1.6027.20.1.1.1.1.1 |
f10BgpM2VersionIndexThe version number of the BGP Protocol.ro Unsigned32 .1.3.6.1.4.1.6027.20.1.1.1.1.1.1 |
f10BgpM2VersionSupportedThis value is TRUE if this version of the BGP protocol identified in 'f10BgpM2VersionIndex' is supported. The absence of a row for a particular f10BgpM2VersionIndex indicates that that f10BgpM2VersionIndex protocol version number is not supported.ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.6027.20.1.1.1.1.1.2 |
f10BgpM2SupportedCapabilities OBJECT IDENTIFIER .1.3.6.1.4.1.6027.20.1.1.2 |
f10BgpM2CapabilitySupportAvailableThis value is TRUE if capability support is available and is enabled.ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.6027.20.1.1.2.1 |
f10BgpM2SupportedCapabilitiesTableTable of supported BGP-4 capabilities. SEQUENCE OF F10BgpM2SupportedCapabilityEntry .1.3.6.1.4.1.6027.20.1.1.2.2 |
f10BgpM2SupportedCapabilitiesEntryInformation about supported capabilities indexed by capability number. F10BgpM2SupportedCapabilityEntry .1.3.6.1.4.1.6027.20.1.1.2.2.1 |
f10BgpM2SupportedCapabilityCodeIndex of supported capability. The index directly corresponds with the BGP-4 Capability Advertisement Capability Code.ro Unsigned32 .1.3.6.1.4.1.6027.20.1.1.2.2.1.1 |
f10BgpM2SupportedCapabilityThis value is True if this capability is supported, False otherwise.ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.6027.20.1.1.2.2.1.2 |
f10BgpM2AsSizeThe size of the AS value in this implementation. The semantics of this are determined as per the as-4bytes draft.ro Enumeration .1.3.6.1.4.1.6027.20.1.1.4 |
f10BgpM2LocalAsThe local autonomous system number. If the f10BgpM2AsSize is twoOctet, then the range is constrained to be 0-65535.ro InetAutonomousSystemNumber (INET-ADDRESS-MIB) .1.3.6.1.4.1.6027.20.1.1.5 |
f10BgpM2LocalIdentifierThe BGP Identifier of local system. Current practice is trending away from this value being treated as an IP address and more as a generic identifier.ro F10BgpM2Identifier .1.3.6.1.4.1.6027.20.1.1.6 |
f10BgpM2BaseScalarExtensions OBJECT IDENTIFIER .1.3.6.1.4.1.6027.20.1.1.7 |
f10BgpM2BaseScalarNonCapExts OBJECT IDENTIFIER .1.3.6.1.4.1.6027.20.1.1.7.1 |
f10BgpM2BaseScalarRouteReflectExts OBJECT IDENTIFIER .1.3.6.1.4.1.6027.20.1.1.7.1.2796 |
f10BgpM2RouteReflectorThis value is TRUE if this implementation supports the BGP Route Reflection Extension and is enabled as a route reflector. If the BGP Route Reflection extension is not supported this value must be FALSE.ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.6027.20.1.1.7.1.2796.1 |
f10BgpM2ClusterIdThe configured Cluster-ID of the BGP Speaker. This will default to the BGP Speaker's F10BgpM2Identifier if this speaker is functioning as a route reflector and an explicit Cluster-ID has not been configured. A value of 0.0.0.0 will be present if Route Reflection is not enabled.ro F10BgpM2Identifier .1.3.6.1.4.1.6027.20.1.1.7.1.2796.2 |
f10BgpM2BaseScalarASConfedExts OBJECT IDENTIFIER .1.3.6.1.4.1.6027.20.1.1.7.1.3065 |
f10BgpM2ConfederationRouterThis value is TRUE if this implementation supports the BGP AS Confederations Extension and this router is configured to be in a confederation.ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.6027.20.1.1.7.1.3065.1 |
f10BgpM2ConfederationIdThe local Confederation Identification Number. This value will be zero (0) if this BGP Speaker is not a confederation router.ro InetAutonomousSystemNumber (INET-ADDRESS-MIB) .1.3.6.1.4.1.6027.20.1.1.7.1.3065.2 |
f10BgpM2BaseScalarCapExts OBJECT IDENTIFIER .1.3.6.1.4.1.6027.20.1.1.7.2 |
f10BgpM2BaseScalarConfiguration OBJECT IDENTIFIER .1.3.6.1.4.1.6027.20.1.1.8 |
f10BgpM2CfgBaseScalarStorageTypeThis object specifies the intended storage type for all configurable base scalars.rw StorageType (SNMPv2-TC) .1.3.6.1.4.1.6027.20.1.1.8.1 |
f10BgpM2CfgLocalAsThe local autonomous system number. If the f10BgpM2AsSize is twoOctet, then the range is constrained to be 0-65535.rw InetAutonomousSystemNumber (INET-ADDRESS-MIB) .1.3.6.1.4.1.6027.20.1.1.8.2 |
f10BgpM2CfgLocalIdentifierThe BGP Identifier of local system. Current practice is trending away from this value being treated as an IP address and more as a generic identifier.rw F10BgpM2Identifier .1.3.6.1.4.1.6027.20.1.1.8.3 |
f10BgpM2CfgBaseScalarExtensions OBJECT IDENTIFIER .1.3.6.1.4.1.6027.20.1.1.8.4 |
f10BgpM2CfgBaseScalarNonCapExts OBJECT IDENTIFIER .1.3.6.1.4.1.6027.20.1.1.8.4.1 |
f10BgpM2CfgBaseScalarReflectorExts OBJECT IDENTIFIER .1.3.6.1.4.1.6027.20.1.1.8.4.1.2796 |
f10BgpM2CfgRouteReflectorThis value is set to true if this implementation will be supporting route reflection.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.6027.20.1.1.8.4.1.2796.1 |
f10BgpM2CfgClusterIdThe configured Cluster-ID of the BGP Speaker. This will default to the BGP Speaker's F10BgpM2Identifier if this speaker is functioning as a route reflector and an explicit Cluster-ID has not been configured. A value of 0.0.0.0 will be present if Route Reflection is not enabled.rw F10BgpM2Identifier .1.3.6.1.4.1.6027.20.1.1.8.4.1.2796.2 |
f10BgpM2CfgBaseScalarASConfedExts OBJECT IDENTIFIER .1.3.6.1.4.1.6027.20.1.1.8.4.1.3065 |
f10BgpM2CfgConfederationRouterThis value is set to true if this implementation will be supporting BGP AS Confederations.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.6027.20.1.1.8.4.1.3065.1 |
f10BgpM2CfgConfederationIdThe local Confederation Identification Number. This value will be zero (0) if this BGP Speaker is not a confederation router.rw InetAutonomousSystemNumber (INET-ADDRESS-MIB) .1.3.6.1.4.1.6027.20.1.1.8.4.1.3065.2 |
f10BgpM2CfgBaseScalarCapExts OBJECT IDENTIFIER .1.3.6.1.4.1.6027.20.1.1.8.4.2 |
f10BgpM2Peer OBJECT IDENTIFIER .1.3.6.1.4.1.6027.20.1.2 |
f10BgpM2PeerData OBJECT IDENTIFIER .1.3.6.1.4.1.6027.20.1.2.1 |
f10BgpM2PeerTableBGP peer table. This table contains, one entry per remote BGP peer, any information about the connections with the remote BGP peers. SEQUENCE OF F10BgpM2PeerEntry .1.3.6.1.4.1.6027.20.1.2.1.1 |
f10BgpM2PeerEntryEntry containing information about the connection with a remote BGP peer. F10BgpM2PeerEntry .1.3.6.1.4.1.6027.20.1.2.1.1.1 |
f10BgpM2PeerInstanceThe routing instance index. Some BGP implementations permit the creation of multiple instances of a BGP routing process. An example includes RFC 2547 PE-CE routers. Implementations that do not support multiple routing instances should return 1 for this object. XXX TODO - We need to provide a way to configure these in the peer configuration table.ro Unsigned32 .1.3.6.1.4.1.6027.20.1.2.1.1.1.1 |
f10BgpM2PeerIdentifierThe BGP Identifier of this entry's remote BGP peer. This entry should be 0.0.0.0 unless the f10BgpM2PeerState is in the OpenConfirm or the Established state.ro F10BgpM2Identifier .1.3.6.1.4.1.6027.20.1.2.1.1.1.2 |
f10BgpM2PeerStateThe remote BGP peer's FSM state.ro Enumeration .1.3.6.1.4.1.6027.20.1.2.1.1.1.3 |
f10BgpM2PeerStatusWhether or not the BGP FSM for this remote peer is halted or running. The BGP FSM for a remote peer is halted after processing a Stop event. Likewise, it is in the running state after a Start event. The f10BgpM2PeerState will generally be in the idle state when the FSM is halted, although some extensions such as Graceful Restart will leave the peer in the Idle state but with the FSM running.ro Enumeration .1.3.6.1.4.1.6027.20.1.2.1.1.1.4 |
f10BgpM2PeerConfiguredVersionThe configured version to originally start with this remote peer. The BGP speaker may permit negotiation to a lower version number of the protocol.ro Unsigned32 .1.3.6.1.4.1.6027.20.1.2.1.1.1.5 |
f10BgpM2PeerNegotiatedVersionThe negotiated version of BGP running between the two peers.ro Unsigned32 .1.3.6.1.4.1.6027.20.1.2.1.1.1.6 |
f10BgpM2PeerLocalAddrTypeThe address family of the local end of the peering session.ro InetAddressType (INET-ADDRESS-MIB) .1.3.6.1.4.1.6027.20.1.2.1.1.1.7 |
f10BgpM2PeerLocalAddrThe address of the local end of the peering session.ro InetAddress .1.3.6.1.4.1.6027.20.1.2.1.1.1.8 |
f10BgpM2PeerLocalPortThe local port for the TCP connection between the BGP peers.ro InetPortNumber (INET-ADDRESS-MIB) .1.3.6.1.4.1.6027.20.1.2.1.1.1.9 |
f10BgpM2PeerLocalAsSome implementations of BGP can represent themselves as multiple ASs. This is the AS that this peering session is representing itself as to the remote peer.ro InetAutonomousSystemNumber (INET-ADDRESS-MIB) .1.3.6.1.4.1.6027.20.1.2.1.1.1.10 |
f10BgpM2PeerRemoteAddrTypeThe address family of the remote end of the peering session.ro InetAddressType (INET-ADDRESS-MIB) .1.3.6.1.4.1.6027.20.1.2.1.1.1.11 |
f10BgpM2PeerRemoteAddrThe address of the remote end of the peering session.ro InetAddress .1.3.6.1.4.1.6027.20.1.2.1.1.1.12 |
f10BgpM2PeerRemotePortThe remote port for the TCP connection between the BGP peers. In the case of a transport for which the notion of 'port' is irrelevant, an instance value of -1 should be returned by the agent for this object. Note that the objects f10BgpM2PeerLocalAddr, f10BgpM2PeerLocalPort, f10BgpM2PeerRemoteAddr and f10BgpM2PeerRemotePort provide the appropriate reference to the standard MIB TCP connection table. or even the ipv6 TCP MIB as in rfc2452.ro InetPortNumber (INET-ADDRESS-MIB) .1.3.6.1.4.1.6027.20.1.2.1.1.1.13 |
f10BgpM2PeerRemoteAsThe remote autonomous system number.ro InetAutonomousSystemNumber (INET-ADDRESS-MIB) .1.3.6.1.4.1.6027.20.1.2.1.1.1.14 |
f10BgpM2PeerIndexThis value is a unique index for the remote peer entry in the f10BgpM2PeerTable. It is assigned by the agent at the point of creation of the f10BgpM2PeerTable row entry. While its value is guaranteed to be unique at any time, it is otherwise opaque to the management application with respect to its value or the contiguity of f10BgpM2PeerIndex row instance values across rows of the f10BgpM2PeerTable. It is used to provide an index structure for other tables whose data is logically per-peer. For explicitly configured peers, this value will remain consistent until this row is deleted by deleting the configured peers. Unconfigured peers will generate a monotonically increasing number when a BGP FSM is built to process the peering session. Values in the f10BgpM2PeerTable and other tables utilizing f10BgpM2PeerIndex are expected to remain in existence for an arbitrary time after the unconfigured peer has been deleted in order to allow management applications to extract useful management information for those peers. Thus, an unconfigured peer using the same indices as the f10BgpM2PeerTable that comes up while this row still exists will re-utilize the same row.ro Unsigned32 .1.3.6.1.4.1.6027.20.1.2.1.1.1.15 |
f10BgpM2PeerErrors OBJECT IDENTIFIER .1.3.6.1.4.1.6027.20.1.2.2 |
f10BgpM2PeerErrorsTableOn a per peer basis, this table reflects the last protocol-defined error encountered and reported on the peer session. If no entry for a given peer, by its f10BgpM2PeerIndex, exists in this table, then no such errors have been observed, reported, and recorded on the session. SEQUENCE OF F10BgpM2PeerErrorsEntry .1.3.6.1.4.1.6027.20.1.2.2.1 |
f10BgpM2PeerErrorsEntryEach entry contains information about errors sent and received for a particular BGP peer. F10BgpM2PeerErrorsEntry .1.3.6.1.4.1.6027.20.1.2.2.1.1 |
f10BgpM2PeerLastErrorReceivedThe last error code and subcode received by this BGP Speaker via a NOTIFICATION message for this peer. If no error has occurred, this field is zero. Otherwise, the first byte of this two byte OCTET STRING contains the error code, and the second byte contains the subcode.ro OCTET STRING .1.3.6.1.4.1.6027.20.1.2.2.1.1.1 |
f10BgpM2PeerLastErrorSentThe last error code and subcode sent by this BGP Speaker via a NOTIFICATION message to this peer. If no error has occurred, this field is zero. Otherwise, the first byte of this two byte OCTET STRING contains the error code, and the second byte contains the subcode.ro OCTET STRING .1.3.6.1.4.1.6027.20.1.2.2.1.1.2 |
f10BgpM2PeerLastErrorReceivedTimeThe timestamp that the last NOTIFICATION was received from this peer.ro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.6027.20.1.2.2.1.1.3 |
f10BgpM2PeerLastErrorSentTimeThe timestamp that the last NOTIFICATION was sent to this peer.ro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.6027.20.1.2.2.1.1.4 |
f10BgpM2PeerLastErrorReceivedTextThis object contains an implementation specific explanation of the error that was reported.ro SnmpAdminString (SNMP-FRAMEWORK-MIB) .1.3.6.1.4.1.6027.20.1.2.2.1.1.5 |
f10BgpM2PeerLastErrorSentTextThis object contains an implementation specific explanation of the error that is being reported.ro SnmpAdminString (SNMP-FRAMEWORK-MIB) .1.3.6.1.4.1.6027.20.1.2.2.1.1.6 |
f10BgpM2PeerLastErrorReceivedDataThe last error code's data seen by this peer.ro OCTET STRING .1.3.6.1.4.1.6027.20.1.2.2.1.1.7 |
f10BgpM2PeerLastErrorSentDataThe last error code's data sent to this peer.ro OCTET STRING .1.3.6.1.4.1.6027.20.1.2.2.1.1.8 |
f10BgpM2PeerTimers OBJECT IDENTIFIER .1.3.6.1.4.1.6027.20.1.2.3 |
f10BgpM2PeerEventTimesTableA table reporting the per-peering session amount of time elapsed and update events since the peering session advanced into the Established state. SEQUENCE OF F10BgpM2PeerEventTimesEntry .1.3.6.1.4.1.6027.20.1.2.3.1 |
f10BgpM2PeerEventTimesEntryEach row contains a set of statistics about time spent and events encountered in the peer session Established state. F10BgpM2PeerEventTimesEntry .1.3.6.1.4.1.6027.20.1.2.3.1.1 |
f10BgpM2PeerFsmEstablishedTimeThis timer indicates how long (in seconds) this peer has been in the Established state or how long since this peer was last in the Established state. It is set to zero when a new peer is configured or the router is booted.ro Gauge32 .1.3.6.1.4.1.6027.20.1.2.3.1.1.1 |
f10BgpM2PeerInUpdatesElapsedTimeElapsed time in seconds since the last BGP UPDATE message was received from the peer. Each time f10BgpM2PeerInUpdates is incremented, the value of this object is set to zero (0). This value shall also be zero (0) when the peer is not in the Established statero Gauge32 .1.3.6.1.4.1.6027.20.1.2.3.1.1.2 |
f10BgpM2PeerConfiguredTimersTablePer peer management data on BGP session timers. SEQUENCE OF F10BgpM2PeerConfiguredTimersEntry .1.3.6.1.4.1.6027.20.1.2.3.2 |
f10BgpM2PeerConfiguredTimersEntryEach entry corresponds to the current state of BGP timers on a given peering session. F10BgpM2PeerConfiguredTimersEntry .1.3.6.1.4.1.6027.20.1.2.3.2.1 |
f10BgpM2PeerConnectRetryIntervalTime interval in seconds for the ConnectRetry timer. The suggested value for this timer is 120 seconds.ro Unsigned32 .1.3.6.1.4.1.6027.20.1.2.3.2.1.1 |
f10BgpM2PeerHoldTimeConfiguredTime interval in seconds for the Hold Time configured for this BGP speaker with this peer. This value is placed in an OPEN message sent to this peer by this BGP speaker, and is compared with the Hold Time field in an OPEN message received from the peer when determining the Hold Time (f10BgpM2PeerHoldTime) with the peer. This value must not be less than three seconds if it is not zero (0) in which case the Hold Time is NOT to be established with the peer. The suggested value for this timer is 90 seconds.ro Unsigned32 ( 0 | 3..65535 ) .1.3.6.1.4.1.6027.20.1.2.3.2.1.2 |
f10BgpM2PeerKeepAliveConfiguredTime interval in seconds for the KeepAlive timer configured for this BGP speaker with this peer. The value of this object will only determine the KEEPALIVE messages frequency relative to the value specified in f10BgpM2PeerHoldTimeConfigured; the actual time interval for the KEEPALIVE messages is indicated by f10BgpM2PeerKeepAlive. A reasonable maximum value for this timer would be configured to be one third of that of f10BgpM2PeerHoldTimeConfigured. If the value of this object is zero (0), no periodical KEEPALIVE messages are sent to the peer after the BGP connection has been established. The suggested value for this timer is 30 seconds.ro Unsigned32 ( 0 | 1..21845 ) .1.3.6.1.4.1.6027.20.1.2.3.2.1.3 |
f10BgpM2PeerMinASOrigIntervalTime interval in seconds for the MinASOriginationInterval timer. The suggested value for this timer is 15 seconds.ro Unsigned32 .1.3.6.1.4.1.6027.20.1.2.3.2.1.4 |
f10BgpM2PeerMinRouteAdverIntervalTime interval in seconds for the MinRouteAdvertisementInterval timer. The suggested value for this timer is 30 seconds.ro Unsigned32 .1.3.6.1.4.1.6027.20.1.2.3.2.1.5 |
f10BgpM2PeerNegotiatedTimersTableCurrent values of per-peer timers which can be dynamically set in the f10BgpM2PeerConfiguredTimersTable. Values reflected in this table are the current operational values, after negotiation from values derived from initial configuration or last set from f10BgpM2PeerConfiguredTimersTable row instances. SEQUENCE OF F10BgpM2PeerNegotiatedTimersEntry .1.3.6.1.4.1.6027.20.1.2.3.3 |
f10BgpM2PeerNegotiatedTimersEntryEach entry reflects a value of the currently operational, negotiated timers as reflected in the F10BgpM2PeerNegotiatedTimersEntry. F10BgpM2PeerNegotiatedTimersEntry .1.3.6.1.4.1.6027.20.1.2.3.3.1 |
f10BgpM2PeerHoldTimeThe value of this object is calculated by this BGP Speaker as being; zero (0) - if this was the value sent by the peer and this value is permitted by this BGP Speaker. In this case, no keepalive messages are sent and the Hold Timer is not set. At least three (3). This value is the smaller of the value sent by this peer in the OPEN message and f10BgpM2PeerHoldTimeConfigured for this peer. This value is only defined when the peering session is in the Established state.ro Unsigned32 ( 0 | 3..65535 ) .1.3.6.1.4.1.6027.20.1.2.3.3.1.1 |
f10BgpM2PeerKeepAliveTime interval in seconds for the KeepAlive timer established with the peer. The value of this object is calculated by this BGP speaker such that, when compared with f10BgpM2PeerHoldTime, it has the same proportion as what f10BgpM2PeerKeepAliveConfigured has when compared with f10BgpM2PeerHoldTimeConfigured. If the value of this object is zero (0), it indicates that the KeepAlive timer has not been established with the peer, or, the value of f10BgpM2PeerKeepAliveConfigured is zero (0). This value is only defined when the peering session is in the Established state.ro Unsigned32 ( 0 | 1..21845 ) .1.3.6.1.4.1.6027.20.1.2.3.3.1.2 |
f10BgpM2PeerCapabilities OBJECT IDENTIFIER .1.3.6.1.4.1.6027.20.1.2.4 |
f10BgpM2PeerCapsAnnouncedTableThis table contains the capabilities that are supported for a given peer. SEQUENCE OF F10BgpM2PeerCapsAnnouncedEntry .1.3.6.1.4.1.6027.20.1.2.4.1 |
f10BgpM2PeerCapsAnnouncedEntryThese entries are keyed by a BGP-4 peer remote address and the BGP Capability Code F10BgpM2PeerCapsAnnouncedEntry .1.3.6.1.4.1.6027.20.1.2.4.1.1 |
f10BgpM2PeerCapAnnouncedCodeThe BGP Capability Advertisement Capability Code.ro Unsigned32 .1.3.6.1.4.1.6027.20.1.2.4.1.1.1 |
f10BgpM2PeerCapAnnouncedIndexMultiple instances of a given capability may be sent bgp a BGP speaker. This variable is used to index them.ro Unsigned32 .1.3.6.1.4.1.6027.20.1.2.4.1.1.2 |
f10BgpM2PeerCapAnnouncedValueThe value of the announced capability.ro OCTET STRING .1.3.6.1.4.1.6027.20.1.2.4.1.1.3 |
f10BgpM2PeerCapsReceivedTableThis table contains the capabilities that are supported for a given peer. SEQUENCE OF F10BgpM24PeerCapsReceivedEntry .1.3.6.1.4.1.6027.20.1.2.4.2 |
f10BgpM2PeerCapsReceivedEntryThese entries are keyed by a BGP-4 peer remote address and the BGP Capability Code F10BgpM24PeerCapsReceivedEntry .1.3.6.1.4.1.6027.20.1.2.4.2.1 |
f10BgpM2PeerCapReceivedCodeThe BGP Capability Advertisement Capability Code.ro Unsigned32 .1.3.6.1.4.1.6027.20.1.2.4.2.1.1 |
f10BgpM2PeerCapReceivedIndexMultiple instances of a given capability may be sent bgp a BGP speaker. This variable is used to index them.ro Unsigned32 .1.3.6.1.4.1.6027.20.1.2.4.2.1.2 |
f10BgpM2PeerCapReceivedValueThe value of the announced capability.ro OCTET STRING .1.3.6.1.4.1.6027.20.1.2.4.2.1.3 |
f10BgpM2PeerCounters OBJECT IDENTIFIER .1.3.6.1.4.1.6027.20.1.2.6 |
f10BgpM2PeerCountersTableThe counters associated with a BGP Peer. SEQUENCE OF F10BgpM2PeerCountersEntry .1.3.6.1.4.1.6027.20.1.2.6.1 |
f10BgpM2PeerCountersEntryEach entry contains counters of message transmissions and FSM transitions for a given BGP Peering session. F10BgpM2PeerCountersEntry .1.3.6.1.4.1.6027.20.1.2.6.1.1 |
f10BgpM2PeerInUpdatesThe number of BGP UPDATE messages received on this connection. This object should be initialized to zero (0) when the connection is established.ro Counter32 .1.3.6.1.4.1.6027.20.1.2.6.1.1.1 |
f10BgpM2PeerOutUpdatesThe number of BGP UPDATE messages transmitted on this connection. This object should be initialized to zero (0) when the connection is established.ro Counter32 .1.3.6.1.4.1.6027.20.1.2.6.1.1.2 |
f10BgpM2PeerInTotalMessagesThe total number of messages received from the remote peer on this connection. This object should be initialized to zero when the connection is established.ro Counter32 .1.3.6.1.4.1.6027.20.1.2.6.1.1.3 |
f10BgpM2PeerOutTotalMessagesThe total number of messages transmitted to the remote peer on this connection. This object should be initialized to zero when the connection is established.ro Counter32 .1.3.6.1.4.1.6027.20.1.2.6.1.1.4 |
f10BgpM2PeerFsmEstablishedTransThe total number of times the BGP FSM transitioned into the established state for this peer.ro Counter32 .1.3.6.1.4.1.6027.20.1.2.6.1.1.5 |
f10BgpM2PeerInKeepalivesThe number of Keepalive messages received from a peer.Implemented by Force10.ro Counter32 .1.3.6.1.4.1.6027.20.1.2.6.1.1.6 |
f10BgpM2PeerOutKeepalivesThe number of Keepalive messages sent to a peer. Implemented by Force10.ro Counter32 .1.3.6.1.4.1.6027.20.1.2.6.1.1.7 |
f10BgpM2PeerInOpenThe number of Open messages received from a peer. Implemented by Force10.ro Counter32 .1.3.6.1.4.1.6027.20.1.2.6.1.1.8 |
f10BgpM2PeerOutOpenThe number of Open messages sent to a peer. Implemented by Force10.ro Counter32 .1.3.6.1.4.1.6027.20.1.2.6.1.1.9 |
f10BgpM2PeerInRteRefreshThe number of Route Refresh messages received from a peer. Implemented by Force10.ro Counter32 .1.3.6.1.4.1.6027.20.1.2.6.1.1.10 |
f10BgpM2PeerOutRteRefreshThe number of Route Refresh messages sent to a peer. Implemented by Force10.ro Counter32 .1.3.6.1.4.1.6027.20.1.2.6.1.1.11 |
f10BgpM2PrefixCountersTableAdditional per-peer, per AFI SAFI counters for prefixes SEQUENCE OF F10BgpM2PrefixCountersEntry .1.3.6.1.4.1.6027.20.1.2.6.2 |
f10BgpM2PrefixCountersEntryEntry containing information about a bgp-peers prefix counters. F10BgpM2PrefixCountersEntry .1.3.6.1.4.1.6027.20.1.2.6.2.1 |
f10BgpM2PrefixCountersAfiThe AFI index of the per-peer, per prefix countersro F10BgpM2Afi .1.3.6.1.4.1.6027.20.1.2.6.2.1.1 |
f10BgpM2PrefixCountersSafiThe SAFI index of the per-peer, per prefix countersro F10BgpM2Safi .1.3.6.1.4.1.6027.20.1.2.6.2.1.2 |
f10BgpM2PrefixInPrefixesThe number of prefixes received from a peer and are stored in the Adj-Ribs-In for that peer.ro Gauge32 .1.3.6.1.4.1.6027.20.1.2.6.2.1.7 |
f10BgpM2PrefixInPrefixesAcceptedThe number of prefixes for a peer that are installed in the Adj-Ribs-In and are eligible to become active in the Loc-Rib.ro Gauge32 .1.3.6.1.4.1.6027.20.1.2.6.2.1.8 |
f10BgpM2PrefixInPrefixesRejectedThe number of prefixes for a peer that are installed in the Adj-Ribs-In and are NOT eligible to become active in the Loc-Rib.ro Gauge32 .1.3.6.1.4.1.6027.20.1.2.6.2.1.9 |
f10BgpM2PrefixOutPrefixesThe number of prefixes for a peer that are installed in that peers Adj-Ribs-Out.ro Gauge32 .1.3.6.1.4.1.6027.20.1.2.6.2.1.10 |
f10BgpM2PrefixWdrawnByPeerThe number of prefixes withdrawn by a peer. Implemened by Force10.ro Gauge32 .1.3.6.1.4.1.6027.20.1.2.6.2.1.11 |
f10BgpM2PrefixWdrawnFromPeerThe number of prefixes withdrawn from a peer. Implemened by Force10.ro Gauge32 .1.3.6.1.4.1.6027.20.1.2.6.2.1.12 |
f10BgpM2PeerExtensions OBJECT IDENTIFIER .1.3.6.1.4.1.6027.20.1.2.7 |
f10BgpM2PeerNonCapExts OBJECT IDENTIFIER .1.3.6.1.4.1.6027.20.1.2.7.1 |
f10BgpM2PeerRouteReflectionExts OBJECT IDENTIFIER .1.3.6.1.4.1.6027.20.1.2.7.1.2796 |
f10BgpM2PeerReflectorClientTableTable of route reflection client settings on a per-peer basis. SEQUENCE OF F10BgpM2PeerReflectorClientEntry .1.3.6.1.4.1.6027.20.1.2.7.1.2796.1 |
f10BgpM2PeerReflectorClientEntryEntry containing data on a per-peer basis on whether the peer is configured as a route reflector client. F10BgpM2PeerReflectorClientEntry .1.3.6.1.4.1.6027.20.1.2.7.1.2796.1.1 |
f10BgpM2PeerReflectorClientThis value indicates whether the given peer is a reflector client of this router, or not. A value of nonClient indicates that this peer is not a reflector client. A value of client indicates that this peer is a reflector client that is not fully meshed with other reflector clients. A value of meshedClient indicates that the peer is a reflector client and is fully meshed with all other reflector clients. This value must be nonClient (0) for BGP external peers.ro Enumeration .1.3.6.1.4.1.6027.20.1.2.7.1.2796.1.1.1 |
f10BgpM2PeerASConfederationExts OBJECT IDENTIFIER .1.3.6.1.4.1.6027.20.1.2.7.1.3065 |
f10BgpM2PeerConfedMemberTableTable of confederation member settings on a per-peer basis. SEQUENCE OF F10BgpM2PeerConfedMemberEntry .1.3.6.1.4.1.6027.20.1.2.7.1.3065.1 |
f10BgpM2PeerConfedMemberEntryEntry containing data on a per-peer basis on whether the peer is configured as a BGP confederation member. F10BgpM2PeerConfedMemberEntry .1.3.6.1.4.1.6027.20.1.2.7.1.3065.1.1 |
f10BgpM2PeerConfedMemberThis value indicates whether the given peer is in our confederation or not.ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.6027.20.1.2.7.1.3065.1.1.1 |
f10BgpM2PeerCapExts OBJECT IDENTIFIER .1.3.6.1.4.1.6027.20.1.2.7.2 |
f10BgpM2PeerConfiguration OBJECT IDENTIFIER .1.3.6.1.4.1.6027.20.1.2.8 |
f10BgpM2CfgPeerAdminStatusTableTable containing rows for administratively starting and stopping peering sessions. SEQUENCE OF F10BgpM2CfgPeerAdminStatusEntry .1.3.6.1.4.1.6027.20.1.2.8.1 |
f10BgpM2CfgPeerAdminStatusEntryEntry containing row for administratively starting and stopping peers. F10BgpM2CfgPeerAdminStatusEntry .1.3.6.1.4.1.6027.20.1.2.8.1.1 |
f10BgpM2CfgPeerAdminStatusThis object allows the Manual Stop and Manual Start events to be sent to an activated peering session.rw Enumeration .1.3.6.1.4.1.6027.20.1.2.8.1.1.1 |
f10BgpM2CfgPeerNextIndexThis object contains the next appropriate value to use as an index for creation of a row instance in in the f10BgpM2CfgPeerTable. If the number of available entries in the f10BgpM2CfgPeerTable is exhausted, a retrieval value of this object instance will return 0. A value of 0 may also be returned if the agent is otherwise incapable of f10BgpM2CfgPeerTable row creation at the time of f10BgpM2CfgPeerNextIndex retrieval.ro Integer32 .1.3.6.1.4.1.6027.20.1.2.8.2 |
f10BgpM2CfgPeerTableBGP configuration peer table. This table allows the configuration of the parameters for a session with a BGP peer. +++wayne provide description of how config should be done for a peer per table. SEQUENCE OF F10BgpM2CfgPeerEntry .1.3.6.1.4.1.6027.20.1.2.8.3 |
f10BgpM2CfgPeerEntryEntry containing information set up by a management entity to configure a connection with a BGP peer. F10BgpM2CfgPeerEntry .1.3.6.1.4.1.6027.20.1.2.8.3.1 |
f10BgpM2CfgPeerConfiguredVersionThe configured version to originally start with this peer. The BGP speaker may permit negotiation to a lower version number of the protocol depending on the set value of f10BgpM2CfgAllowVersionNegotiation.rw Unsigned32 .1.3.6.1.4.1.6027.20.1.2.8.3.1.1 |
f10BgpM2CfgAllowVersionNegotiationIf set to true, during session establishment with this peer, negotiation to a version lower than that specified in f10BgpM2CfgPeerConfiguredVersion will be allowed.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.6027.20.1.2.8.3.1.2 |
f10BgpM2CfgPeerLocalAddrTypeThe address family of the speakers of this BGP session.rw InetAddressType (INET-ADDRESS-MIB) .1.3.6.1.4.1.6027.20.1.2.8.3.1.3 |
f10BgpM2CfgPeerLocalAddrThe address of the local end of the peering session.rw InetAddress .1.3.6.1.4.1.6027.20.1.2.8.3.1.4 |
f10BgpM2CfgPeerLocalAsAutonomous system represented to peer on peering session initialization. Some implementations of BGP can represent themselves as multiple ASes. These implementations can set this to an alternate autonomous system. If this object is set to zero (0) at the point this row instance is set to active, then the implementation will initialize this session representing itself as the value of f10BgpM2CfgLocalAs.rw InetAutonomousSystemNumber (INET-ADDRESS-MIB) .1.3.6.1.4.1.6027.20.1.2.8.3.1.5 |
f10BgpM2CfgPeerRemoteAddrTypeThe address family of the speakers of the remote BGP session.rw InetAddressType (INET-ADDRESS-MIB) .1.3.6.1.4.1.6027.20.1.2.8.3.1.6 |
f10BgpM2CfgPeerRemoteAddrThe address of the remote end (destination address of peer) for peering session.rw InetAddress .1.3.6.1.4.1.6027.20.1.2.8.3.1.7 |
f10BgpM2CfgPeerRemoteAsAutonomous system number of the remote peer.rw InetAutonomousSystemNumber (INET-ADDRESS-MIB) .1.3.6.1.4.1.6027.20.1.2.8.3.1.8 |
f10BgpM2CfgPeerEntryStorageTypeThis object type specifies the intended storage type for the f10BgpM2CfgPeerEntry row instance.rw StorageType (SNMPv2-TC) .1.3.6.1.4.1.6027.20.1.2.8.3.1.9 |
f10BgpM2CfgPeerErrorThis value indicates the current error status of the row denoting the configured error status. If this row is still under creation (has not been activated f10BgpM2CfgPeerRowEntryStatus), then this instance will be set to not-activated (1). At the point that the row is activated, f10BgpM2CfgPeerError will reflect the error status of the row data itself. If there is another session already activated with the same local and remote addresses as denoted by {f10BgpM2CfgPeerLocalAddrType, f10BgpM2CfgPeerLocalAddr, f10BgpM2CfgPeerRemoteAddr}, then the value of this will be set to err-duplicate-peering-session (2). If this row is associated with a peer session whose initialization has been attempted, the value will be set to activated (3) (and, f10BgpM2PeerCfgPeerEntry will be set to the row instance of the entry in the f10BgpM2PeerTable which reflects the state of the peering session). Note that this object only reflects the error as a function of the attempted activation of this row as containing data for a bgp peering session. The actual state of the session at the point of any protocol exchange or session state machine initiation is reflected in the f10BgpM2PeerTable row instance (as reflected through f10BgpM2CfgPeerPeerEntry) associated with this row instance.ro Enumeration .1.3.6.1.4.1.6027.20.1.2.8.3.1.10 |
f10BgpM2CfgPeerBgpPeerEntryUpon activation of the session data contained in this row instance, this object points to an instance of a row within the f10BgpM2PeerTable reflecting the session in its initializing or operational state. Retrieval of this column instance will always yield a value of {0.0} unless the session has successfully been activated (via f10BgpM2CfgPeerRowEntryStatus). Such row instances will always have a value of f10BgpM2CfgPeerError which is activated (3).ro RowPointer (SNMPv2-TC) .1.3.6.1.4.1.6027.20.1.2.8.3.1.11 |
f10BgpM2CfgPeerRowEntryStatusThis object type is used to control creation, activation, and deletion of this row instance.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.6027.20.1.2.8.3.1.12 |
f10BgpM2CfgPeerIndexUniquely identifies an instance of a peer row, as an element of configuration.ro Integer32 .1.3.6.1.4.1.6027.20.1.2.8.3.1.13 |
f10BgpM2CfgPeerStatusThis specifies the state of the peering session upon activation. If disabled, the FSM is in the halted state and no Automatic Start events are generated. If enabled, the FSM is in the running state and Automatic Start events may be generated.rw Enumeration .1.3.6.1.4.1.6027.20.1.2.8.3.1.14 |
f10BgpM2CfgPeerTimersTableTable for configuration of per-peer timers. SEQUENCE OF F10BgpM2CfgPeerTimersEntry .1.3.6.1.4.1.6027.20.1.2.8.4 |
f10BgpM2CfgPeerTimersEntryEntry containing per-peer timer configuration. F10BgpM2CfgPeerTimersEntry .1.3.6.1.4.1.6027.20.1.2.8.4.1 |
f10BgpM2CfgPeerConnectRetryIntervalTime interval in seconds for the ConnectRetry timer. The suggested value for this timer is 120 seconds.rw Unsigned32 .1.3.6.1.4.1.6027.20.1.2.8.4.1.1 |
f10BgpM2CfgPeerHoldTimeConfiguredTime interval in seconds for the Hold Time configured for this BGP speaker with this peer. This value is placed in an OPEN message sent to this peer by this BGP speaker, and is compared with the Hold Time field in an OPEN message received from the peer when determining the Hold Time (f10BgpM2PeerHoldTime) with the peer. This value must not be less than three seconds if it is not zero (0) in which case the Hold Time is NOT to be established with the peer. The suggested value for this timer is 90 seconds.rw Unsigned32 ( 0 | 3..65535 ) .1.3.6.1.4.1.6027.20.1.2.8.4.1.2 |
f10BgpM2CfgPeerKeepAliveConfiguredTime interval in seconds for the KeepAlive timer configured for this BGP speaker with this peer. The value of this object will only determine the KEEPALIVE messages frequency relative to the value specified in f10BgpM2PeerHoldTimeConfigured; the actual time interval for the KEEPALIVE messages is indicated by f10BgpM2PeerKeepAlive. A reasonable maximum value for this timer would be configured to be one third of that of f10BgpM2PeerHoldTimeConfigured. If the value of this object is zero (0), no periodical KEEPALIVE messages are sent to the peer after the BGP connection has been established. The suggested value for this timer is 30 seconds.rw Unsigned32 ( 0 | 1..21845 ) .1.3.6.1.4.1.6027.20.1.2.8.4.1.3 |
f10BgpM2CfgPeerMinASOrigIntervalTime interval in seconds for the MinASOriginationInterval timer. The suggested value for this timer is 15 seconds.rw Unsigned32 .1.3.6.1.4.1.6027.20.1.2.8.4.1.4 |
f10BgpM2CfgPeerMinRouteAdverInterTime interval in seconds for the MinRouteAdvertisementInterval timer. The suggested value for this timer is 30 seconds.rw Unsigned32 .1.3.6.1.4.1.6027.20.1.2.8.4.1.5 |
f10BgpM2CfgPeerExtensions OBJECT IDENTIFIER .1.3.6.1.4.1.6027.20.1.2.8.5 |
f10BgpM2CfgPeerNonCapExts OBJECT IDENTIFIER .1.3.6.1.4.1.6027.20.1.2.8.5.1 |
f10BgpM2CfgPeerRouteReflectionExts OBJECT IDENTIFIER .1.3.6.1.4.1.6027.20.1.2.8.5.1.2796 |
f10BgpM2CfgPeerReflectorClientTableTable of route reflection client settings on a per-peer basis. SEQUENCE OF F10BgpM2CfgPeerReflectorClientEntry .1.3.6.1.4.1.6027.20.1.2.8.5.1.2796.1 |
f10BgpM2CfgPeerReflectorClientEntryEntry containing data on a per-peer basis on whether the peer is configured as a route reflector client. F10BgpM2CfgPeerReflectorClientEntry .1.3.6.1.4.1.6027.20.1.2.8.5.1.2796.1.1 |
f10BgpM2CfgPeerReflectorClientThis value indicates whether the given peer is a reflector client of this router, or not. A value of nonClient indicates that this peer is not a reflector client. A value of client indicates that this peer is a reflector client that is not fully meshed with other reflector clients. A value of meshedClient indicates that the peer is a reflector client and is fully meshed with all other reflector clients. This value must be nonClient (0) for BGP external peers.rw Enumeration .1.3.6.1.4.1.6027.20.1.2.8.5.1.2796.1.1.1 |
f10BgpM2CfgPeerASConfederationExts OBJECT IDENTIFIER .1.3.6.1.4.1.6027.20.1.2.8.5.1.3065 |
f10BgpM2CfgPeerConfedMemberTableTable of confederation member settings on a per-peer basis. SEQUENCE OF F10BgpM2CfgPeerConfedMemberEntry .1.3.6.1.4.1.6027.20.1.2.8.5.1.3065.1 |
f10BgpM2CfgPeerConfedMemberEntryEntry containing data on a per-peer basis on whether the peer is configured as a BGP confederation member. F10BgpM2CfgPeerConfedMemberEntry .1.3.6.1.4.1.6027.20.1.2.8.5.1.3065.1.1 |
f10BgpM2CfgPeerConfedMemberThis value indicates whether the given peer is in our confederation or not.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.6027.20.1.2.8.5.1.3065.1.1.1 |
f10BgpM2CfgPeerCapExts OBJECT IDENTIFIER .1.3.6.1.4.1.6027.20.1.2.8.5.2 |
f10BgpM2Rib OBJECT IDENTIFIER .1.3.6.1.4.1.6027.20.1.3 |
f10BgpM2NlriTableThe BGP-4 Received Path Attribute Table contains information about paths to destination networks received from all BGP4 peers. Collectively, this represents the Adj-Ribs-In. The route where f10BgpM2NlriBest is TRUE represents, for this NLRI, the route that is installed in the LocRib from the Adj-Ribs-In. SEQUENCE OF F10BgpM2NlriEntry .1.3.6.1.4.1.6027.20.1.3.1 |
f10BgpM2NlriEntryInformation about a path to a network. F10BgpM2NlriEntry .1.3.6.1.4.1.6027.20.1.3.1.1 |
f10BgpM2NlriIndexThis index allows for multiple instances of a base prefix for a certain AFI SAFI from a given peer. This is currently useful for two things: 1. Allowing for a peer in future implementations to send more than a single route instance. 2. Allow for extensions which extend the NLRI field to send the same prefix while utilizing other extension specific information. An example of this is RFC 3107 - Carrying MPLS labels in BGP.ro Unsigned32 .1.3.6.1.4.1.6027.20.1.3.1.1.1 |
f10BgpM2NlriAfiThe address family of the prefix for this NLRI.ro F10BgpM2Afi .1.3.6.1.4.1.6027.20.1.3.1.1.2 |
f10BgpM2NlriSafiThe subsequent address family of the prefix for this NLRIro F10BgpM2Safi .1.3.6.1.4.1.6027.20.1.3.1.1.3 |
f10BgpM2NlriPrefixTypeThe type of the IP address prefix in the Network Layer Reachability Information field. The value of this object is derived from the appropriate value from the f10BgpM2NlriAfi field. Where an appropriate InetAddressType is not available, the value of the object must be unknown(0). XXX TODO - This seems like a hack.ro InetAddressType (INET-ADDRESS-MIB) .1.3.6.1.4.1.6027.20.1.3.1.1.4 |
f10BgpM2NlriPrefixAn IP address prefix in the Network Layer Reachability Information field. This object is an IP address containing the prefix with length specified by f10BgpM2PathAttrAddrPrefixLen. Any bits beyond the length specified by f10BgpM2PathAttrAddrPrefixLen are zeroed.ro InetAddress .1.3.6.1.4.1.6027.20.1.3.1.1.5 |
f10BgpM2NlriPrefixLenLength in bits of the address prefix in the Network Layer Reachability Information field.ro InetAddressPrefixLength (INET-ADDRESS-MIB) .1.3.6.1.4.1.6027.20.1.3.1.1.6 |
f10BgpM2NlriBestAn indication of whether or not this route was chosen as the best BGP4 route.ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.6027.20.1.3.1.1.7 |
f10BgpM2NlriCalcLocalPrefThe degree of preference calculated by the receiving BGP4 speaker for an advertised route.ro Unsigned32 .1.3.6.1.4.1.6027.20.1.3.1.1.8 |
f10BgpM2PathAttrIndexThis value is a unique index for the per-NLRI entry in the f10BgpM2PathAttrTable. It is assigned by the agent at the point of creation of the f10BgpM2PathAttrTable row entry. While its value is guaranteed to be unique at any time, it is otherwise opaque to the management application with respect to its value or the contiguity of f10BgpM2PathAttrIndex row instance values across rows of the f10BgpM2PeerAttrTable. It is used to provide an index structure for other tables whose data is logically per-peer, per-NLRI.ro Unsigned32 .1.3.6.1.4.1.6027.20.1.3.1.1.9 |
f10BgpM2NlriOpaqueTypeThis object enumerates the type of the row that is pointed to in the table row f10BgpM2NlriOpaquePointer instance, if f10BgpM2NlriOpaquePointer is in fact not a zero length. f10BgpM2NlriOpaqueType is necessary since the data referenced by f10BgpM2NlriOpaquePointer is opaque to BGP. For example, in the case of RFC 3107, the label stack that is pointed to may occur in the mplsLabelStackTable from the MPLS-LSR-MIB, and the instance value of f10BgpM2NlriOpaqueType would be bgpMplsLabelStack(1).ro Enumeration .1.3.6.1.4.1.6027.20.1.3.1.1.10 |
f10BgpM2NlriOpaquePointerPointer to a row that decomposes the data that is opaque to the BGP MIB but is sent in the NLRI. This RowPointer has zero (0) length data instance if f10BgpM2NlriOpaqueType is none.ro RowPointer (SNMPv2-TC) .1.3.6.1.4.1.6027.20.1.3.1.1.11 |
f10BgpM2AdjRibsOutTableThis table contains on a per-peer basis one or more routes from the f10BgpM2NlriTable that have been placed in this peer's Adj-Ribs-Out. SEQUENCE OF F10BgpM2AdjRibsOutEntry .1.3.6.1.4.1.6027.20.1.3.2 |
f10BgpM2AdjRibsOutEntryList of BGP routes that have been placed into a peer's Adj-Ribs-Out. F10BgpM2AdjRibsOutEntry .1.3.6.1.4.1.6027.20.1.3.2.1 |
f10BgpM2AdjRibsOutIndexCertain extensions to BGP permit multiple instance of a per afi, per safi prefix to be advertised to a peer. This object allows the enumeration of them.ro Unsigned32 .1.3.6.1.4.1.6027.20.1.3.2.1.1 |
f10BgpM2AdjRibsOutRouteThis object points to the route in the f10BgpM2NlriTable that corresponds to the entry in the peer's Adj-Rib-Out. Outgoing route maps are not reflected at this point as those are part of the Update-Send process.ro RowPointer (SNMPv2-TC) .1.3.6.1.4.1.6027.20.1.3.2.1.2 |
f10BgpM2PathAttrCountThe number of entries in the f10BgpM2PathAttrTable.ro Counter32 .1.3.6.1.4.1.6027.20.1.3.3 |
f10BgpM2PathAttrTableProvides per advertised network-prefix attribute data, as advertised over a peering session. SEQUENCE OF F10BgpM2PathAttrEntry .1.3.6.1.4.1.6027.20.1.3.4 |
f10BgpM2PathAttrEntryEach entry contains data about a given network prefix, per-prefix and per-advertising peer. F10BgpM2PathAttrEntry .1.3.6.1.4.1.6027.20.1.3.4.1 |
f10BgpM2PathAttrOriginThe ultimate origin of the path information.ro Enumeration .1.3.6.1.4.1.6027.20.1.3.4.1.1 |
f10BgpM2PathAttrNextHopAddrTypeThe address family of the address for the border router that should be used to access the destination network.ro InetAddressType (INET-ADDRESS-MIB) .1.3.6.1.4.1.6027.20.1.3.4.1.2 |
f10BgpM2PathAttrNextHopThe address of the border router that should be used to access the destination network. This address is the nexthop address received in the UPDATE packet. The address family of this object will be the same as that of the prefix in this row. Note that for RFC2545 style double nexthops, this object will always contain the global scope nexthop. f10BgpM2LinkLocalNextHopTable will contain the linklocal scope nexthop. In the case that the mechanism documented in draft-kato-bgp-ipv6-link-local-00.txt is used and only a link local nexthop has been sent, , f10BgpM2LinkLocalNextHopPresent will be false and f10BgpM2PathAttrNextHop will contain the link local nexthop.ro InetAddress .1.3.6.1.4.1.6027.20.1.3.4.1.3 |
f10BgpM2PathAttrMedPresentWhether or not the MED value is present. If it is not present, the f10BgpM2PathAttrMed object has no useful value and should be set to 0.ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.6027.20.1.3.4.1.4 |
f10BgpM2PathAttrMedThis metric is used to discriminate between multiple exit points to an adjacent autonomous system.ro Unsigned32 .1.3.6.1.4.1.6027.20.1.3.4.1.5 |
f10BgpM2PathAttrLocalPrefPresentWhether or not the LocalPref value is present. If it is not present, the f10BgpM2PathAttrLocalPref object has no useful value and should be set to 0.ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.6027.20.1.3.4.1.6 |
f10BgpM2PathAttrLocalPrefThe originating BGP4 speakers degree of preference for an advertised route.ro Unsigned32 .1.3.6.1.4.1.6027.20.1.3.4.1.7 |
f10BgpM2PathAttrAtomicAggregateWhen this object is set to atomicAggregatePresent, the ATOMIC_AGGREGATE Path Attribute is present and indicates that the NLRI MUST NOT be made more specific.ro Enumeration .1.3.6.1.4.1.6027.20.1.3.4.1.8 |
f10BgpM2PathAttrAggregatorASThe AS number of the last BGP4 speaker that performed route aggregation. A value of zero (0) indicates the absence of this attribute. Note propagation of AS of zero is illegal in the Internet.ro InetAutonomousSystemNumber (INET-ADDRESS-MIB) .1.3.6.1.4.1.6027.20.1.3.4.1.9 |
f10BgpM2PathAttrAggregatorAddrThe IP address of the last BGP4 speaker that performed route aggregation. A value of 0.0.0.0 indicates the absence of this attribute.ro F10BgpM2Identifier .1.3.6.1.4.1.6027.20.1.3.4.1.10 |
f10BgpM2AsPathCalcLengthThis value represents the calculated length of the AS Path according to the rules of the BGP specification. This value is used in route selection.ro Unsigned32 .1.3.6.1.4.1.6027.20.1.3.4.1.11 |
f10BgpM2AsPathStringThis is a string depicting the autonomous system path to this network which was received from the peer which advertised it. The format of the string is implementation-dependent, and should be designed for operator readability.ro SnmpAdminString (SNMP-FRAMEWORK-MIB) .1.3.6.1.4.1.6027.20.1.3.4.1.12 |
f10BgpM2AsPathIndexThis value is a unique index for the decomposed AS Path in the f10BgpM2AsPathTable. It is assigned by the agent at the point of creation of the f10BgpM2AsPathTable row entry. While its value is guaranteed to be unique at any time, it is otherwise opaque to the management application with respect to its value or the contiguity of f10BgpM2AsPathIndex row instance values across rows of the f10BgpM2AsPathTable.ro Unsigned32 .1.3.6.1.4.1.6027.20.1.3.4.1.13 |
f10BgpM2AsPath4byteTableThis table is present for BGP speakers that support the AS 4byte specification and are functioning as a router between 2-byte and 4-byte AS space. SEQUENCE OF F10BgpM2AsPath4byteEntry .1.3.6.1.4.1.6027.20.1.3.5 |
f10BgpM2AsPath4byteEntryEach row contains the information for the AS 4-byte extension's NEW_AS_PATH and NEW_AGGREGATOR attributes. F10BgpM2AsPath4byteEntry .1.3.6.1.4.1.6027.20.1.3.5.1 |
f10BgpM2AsPath4bytePathPresentThis value may only be true if this BGP Speaker is functioning as a router between ASs that are in 2-byte and 4-byte AS space. If this value is true, then the NEW_AS_PATH attributes are present and the 4-byte versions of the appropriate path attributes are in this row. If this value is false, then the following values will be present in the row: f10BgpM2PathAttrAggregatorAS - zero (0). f10BgpM2AsPathCalcLength - zero (0). f10BgpM2AsPathString - zero (0) length string. f10BgpM2AsPathIndex - zero (0).ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.6027.20.1.3.5.1.1 |
f10BgpM2AsPath4byteAggregatorASThe NEW_AGGREGATOR AS number of the last BGP4 speaker that performed route aggregation. A value of zero (0) indicates the absence of this attribute. Note propagation of AS of zero is illegal in the Internet.ro InetAutonomousSystemNumber (INET-ADDRESS-MIB) .1.3.6.1.4.1.6027.20.1.3.5.1.2 |
f10BgpM2AsPath4byteCalcLengthThis value represents the calculated length of the NEW_AS_PATH according to the rules of the BGP specification. This value is used in route selection.ro Unsigned32 .1.3.6.1.4.1.6027.20.1.3.5.1.3 |
f10BgpM2AsPath4byteStringThis is a string depicting the autonomous system path to this network which was received from the peer which advertised it. The format of the string is implementation-dependent, and should be designed for operator readability.ro SnmpAdminString (SNMP-FRAMEWORK-MIB) .1.3.6.1.4.1.6027.20.1.3.5.1.4 |
f10BgpM2AsPath4byteIndexThis value is a unique index for the decomposed AS Path in the f10BgpM2AsPathTable. It is assigned by the agent at the point of creation of the f10BgpM2AsPathTable row entry. While its value is guaranteed to be unique at any time, it is otherwise opaque to the management application with respect to its value or the contiguity of f10BgpM2AsPathIndex row instance values across rows of the f10BgpM2AsPathTable.ro Unsigned32 .1.3.6.1.4.1.6027.20.1.3.5.1.5 |
f10BgpM2AsPathTableThe BGP-4 Path Attribute AS Path Table contains the per network path (NLRI) AS PATH data received from the advertising BGP peer. SEQUENCE OF F10BgpM2AsPathEntry .1.3.6.1.4.1.6027.20.1.3.6 |
f10BgpM2AsPathTableEntryInformation about an AS path provided with a path to a network. F10BgpM2AsPathEntry .1.3.6.1.4.1.6027.20.1.3.6.1 |
f10BgpM2AsPathSegmentIndexA per-AS path segment index. This will index a set of autonomous systems in an AS path which are part of the same sequence or set (as determined by the row value of f10BgpM2AsPathType, which should be the same value for each f10BgpM2AsPathTable entry indexed by the same (f10BgpM2PathAttrIndex, f10BgpM2AsPathIndex) pair).ro Unsigned32 .1.3.6.1.4.1.6027.20.1.3.6.1.1 |
f10BgpM2AsPathElementIndexA per-AS element index. This will index a particular AS within a sequence or set of autonomous systems in an AS path.ro Unsigned32 .1.3.6.1.4.1.6027.20.1.3.6.1.2 |
f10BgpM2AsPathTypeThe type of sequence in which this asPath was advertised as an attribute. Note that all asPath row instances for a given (f10BgpM2PathAttrIndex, f10BgpM2AsPathIndex) index pair will have their f10BgpM2AsPathType set to the same value. The values for f10BgpM2AsPathType are interpreted as defined in the base BGP document and the BGP AS Confederations document.ro Enumeration .1.3.6.1.4.1.6027.20.1.3.6.1.3 |
f10BgpM2AsPathElementValueAn AS value for an AS the related NLRI traversed in the propagation of its advertisement. This value is to be interpreted in the context of the sequence implied by f10BgpM2AsPathIndex and f10BgpM2AsPathType (and, in sequence of the other table rows with the same value of f10BgpM2PathAttrIndex and f10BgpM2AsPathIndex).ro InetAutonomousSystemNumber (INET-ADDRESS-MIB) .1.3.6.1.4.1.6027.20.1.3.6.1.4 |
f10BgpM2PathAttrUnknownTableThe BGP-4 Path Attribute Unknown Table contains the per network path (NLRI) data on the path attributes advertised with a route but not known to the local BGP implementation or not otherwise capable of being returned from this agent. The absence of row data for a given index value for f10BgpM2PathAttrIndex indicates a lack of such unknown attribute information for the indicated network path (as indexed by that f10BgpM2PathAttrIndex value in the f10BgpM2PathAttrTable). SEQUENCE OF F10BgpM2PathAttrUnknownEntry .1.3.6.1.4.1.6027.20.1.3.7 |
f10BgpM2PathAttrUnknownEntryInformation about an unknown attribute provided with a path to a network. F10BgpM2PathAttrUnknownEntry .1.3.6.1.4.1.6027.20.1.3.7.1 |
f10BgpM2PathAttrUnknownIndexAn integer index for a row in this table.ro Unsigned32 .1.3.6.1.4.1.6027.20.1.3.7.1.1 |
f10BgpM2PathAttrUnknownTypeThe attribute type advertised with this unknown attribute by the peer.ro Unsigned32 .1.3.6.1.4.1.6027.20.1.3.7.1.2 |
f10BgpM2PathAttrUnknownValueValue of path attribute not understood by the base BGP-4 document. Octets beyond the maximum size, if any, are not recorded by this row object.ro OCTET STRING .1.3.6.1.4.1.6027.20.1.3.7.1.3 |
f10BgpM2PathAttrExtensions OBJECT IDENTIFIER .1.3.6.1.4.1.6027.20.1.3.8 |
f10BgpM2PathAttrNonCapExts OBJECT IDENTIFIER .1.3.6.1.4.1.6027.20.1.3.8.1 |
f10BgpM2PathAttrCommunityExts OBJECT IDENTIFIER .1.3.6.1.4.1.6027.20.1.3.8.1.1997 |
f10BgpM2PathAttrCommTableThe BGP-4 Path Attribute Community Table contains the per network path (NLRI) data on the community membership advertised with a route. The absence of row data for a given index value for f10BgpM2PathAttrIndex indicates a lack of this attribute information for the indicated network path (as indexed by that f10BgpM2PathAttrIndex value in the f10BgpM2PathAttrTable). SEQUENCE OF F10BgpM2PathAttrCommEntry .1.3.6.1.4.1.6027.20.1.3.8.1.1997.1 |
f10BgpM2PathAttrCommEntryInformation about a community association provided with a path to a network. F10BgpM2PathAttrCommEntry .1.3.6.1.4.1.6027.20.1.3.8.1.1997.1.1 |
f10BgpM2PathAttrCommIndexAn integer index for a row in this table.ro Unsigned32 .1.3.6.1.4.1.6027.20.1.3.8.1.1997.1.1.1 |
f10BgpM2PathAttrCommValueA value representing a community. There are certain 4-octet long values which could be returned in this columnar row data that carry additional semantics.ro F10BgpM2Community .1.3.6.1.4.1.6027.20.1.3.8.1.1997.1.1.2 |
f10BgpM2LinkLocalNextHopTableTable of link local nexthops as sent by RFC 2545 for IPv6 BGP Speakers. SEQUENCE OF F10BgpM2LinkLocalNextHopEntry .1.3.6.1.4.1.6027.20.1.3.8.1.2545 |
f10BgpM2LinkLocalNextHopEntryEntry containing the link-local nexthops as sent by a BGP speaker running RFC 2545 extensions for double-nexthops. F10BgpM2LinkLocalNextHopEntry .1.3.6.1.4.1.6027.20.1.3.8.1.2545.1 |
f10BgpM2LinkLocalNextHopPresentThis value is TRUE if and only if the BGP speaker is receiving IPv6 NLRI using the RFC 2545 double nexthop convention and it has received a link local scope nexthop in addition to the global scope nexthop.ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.6027.20.1.3.8.1.2545.1.1 |
f10BgpM2LinkLocalNextHopThis value contains an IPv6 link local address of InetAddressType of type ipv6z. This value is only present if f10BgpM2LinkLocalNextHopPresent is true.ro InetAddress .1.3.6.1.4.1.6027.20.1.3.8.1.2545.1.2 |
f10BgpM2PathAttrRouteReflectionExts OBJECT IDENTIFIER .1.3.6.1.4.1.6027.20.1.3.8.1.2796 |
f10BgpM2PathAttrOriginatorIdTablePer prefix data pertinent to advertisement of a network prefix through an originator. SEQUENCE OF F10BgpM2PathAttrOriginatorIdEntry .1.3.6.1.4.1.6027.20.1.3.8.1.2796.1 |
f10BgpM2PathAttrOriginatorIdEntryEach entry contains data pertinent to a network prefix as received through its originating BGP route reflector. F10BgpM2PathAttrOriginatorIdEntry .1.3.6.1.4.1.6027.20.1.3.8.1.2796.1.1 |
f10BgpM2PathAttrOriginatorIdThe Originator-ID identifying the router that initially advertised this destination to a Route Reflector. A value of 0.0.0.0 indicates the absence of this attribute.ro F10BgpM2Identifier .1.3.6.1.4.1.6027.20.1.3.8.1.2796.1.1.1 |
f10BgpM2PathAttrClusterTableThe BGP-4 Path Attribute Cluster Table contains the per network path (NLRI) data on the reflection path which a route has traversed. The absence of row data for a given index value for f10BgpM2PathAttrIndex indicates a lack of this attribute information for the indicated network path (as indexed by that f10BgpM2PathAttrIndex value in the f10BgpM2PathAttrTable). SEQUENCE OF F10BgpM2PathAttrClusterEntry .1.3.6.1.4.1.6027.20.1.3.8.1.2796.2 |
f10BgpM2PathAttrClusterEntryInformation about a cluster traversal provided with a path to a network. F10BgpM2PathAttrClusterEntry .1.3.6.1.4.1.6027.20.1.3.8.1.2796.2.1 |
f10BgpM2PathAttrClusterIndexAn integral index for a row in this table.ro Unsigned32 .1.3.6.1.4.1.6027.20.1.3.8.1.2796.2.1.1 |
f10BgpM2PathAttrClusterValueA four octet long value representing a part of the reflection path that the route has passed. Each such four octet long value represents the ID of a cluster that the route has traversed. The sequence of this path as received in the route advertisement will be preserved in the sequence of f10BgpM2PathAttrClusterTable rows (and the f10BgpM2PathAttrClusterValues in each row) as returned for a given f10BgpM2PathAttrIndex value, and the monotonically increasing sequence of f10BgpM2PathAttrClusterIndex values for that f10BgpM2PathAttrIndex.ro F10BgpM2Identifier .1.3.6.1.4.1.6027.20.1.3.8.1.2796.2.1.2 |
f10BgpM2PathAttrExtCommTableThe BGP-4 Path Attribute Community Table contains the per network path (NLRI) data on the extended community membership advertised with a route. The absence of row data for a given index value for f10BgpM2PathAttrIndex indicates a lack of this attribute information for the indicated network path (as indexed by that f10BgpM2PathAttrIndex value in the f10BgpM2PathAttrTable). XXX JMH - can not assign the OID until an RFC is published. SEQUENCE OF F10BgpM2PathAttrExtCommEntry .1.3.6.1.4.1.6027.20.1.3.8.1.3501 |
f10BgpM2PathAttrExtCommEntryInformation about an extended community association provided with a path to a network. F10BgpM2PathAttrExtCommEntry .1.3.6.1.4.1.6027.20.1.3.8.1.3501.1 |
f10BgpM2PathAttrExtCommIndexAn integral index for a row in this table.ro Unsigned32 .1.3.6.1.4.1.6027.20.1.3.8.1.3501.1.1 |
f10BgpM2PathAttrExtCommValueA value representing an extended community which was received with the route implied by the f10BgpM2PathAttr Index value of this row data. There are certain 8-octet long values which could be returned in this columnar row data that carry additional semantics.ro F10BgpM2ExtendedCommunity .1.3.6.1.4.1.6027.20.1.3.8.1.3501.1.2 |
f10BgpM2PathAttrCapExts OBJECT IDENTIFIER .1.3.6.1.4.1.6027.20.1.3.8.2 |
f10BgpM2Conformance OBJECT IDENTIFIER .1.3.6.1.4.1.6027.20.1.4 |
f10BgpM2MIBCompliances OBJECT IDENTIFIER .1.3.6.1.4.1.6027.20.1.4.1 |
f10BgpM2MIBComplianceThe compliance statement for entities which implement the BGP4 mib. Unknown .1.3.6.1.4.1.6027.20.1.4.1.1 |
f10BgpM2MIBGroups OBJECT IDENTIFIER .1.3.6.1.4.1.6027.20.1.4.2 |
f10BgpM2CommunitiesGroupObjects associated with BGP communities. Unknown .1.3.6.1.4.1.6027.20.1.4.2.1 |
f10BgpM2ExtCommunitiesGroupObjects associated with BGP extended communities. Unknown .1.3.6.1.4.1.6027.20.1.4.2.2 |
f10BgpM2RouteReflectionGroupObjects associated with BGP route reflection. Unknown .1.3.6.1.4.1.6027.20.1.4.2.3 |
f10BgpM2AsConfederationGroupObjects associated with BGP confederation membership. Unknown .1.3.6.1.4.1.6027.20.1.4.2.4 |
f10BgpM2TimersGroupObjects associated with BGP peering timers. Unknown .1.3.6.1.4.1.6027.20.1.4.2.5 |
f10BgpM2CountersGroupObjects to count discrete events and exchanges on BGP sessions. Unknown .1.3.6.1.4.1.6027.20.1.4.2.6 |
f10BgpM2CapabilitiesGroupObjects to report capabilities as received on BGP sessions. Unknown .1.3.6.1.4.1.6027.20.1.4.2.7 |
f10BgpM2AsPathGroupObjects to report AS paths received on BGP NLRIs. Unknown .1.3.6.1.4.1.6027.20.1.4.2.8 |
f10BgpM2As4byteGroupAS Size objects. Unknown .1.3.6.1.4.1.6027.20.1.4.2.9 |
f10BgpM2BaseGroupBasic objects in local BGP implementation. Unknown .1.3.6.1.4.1.6027.20.1.4.2.10 |
f10BgpM2ErrorsGroupErrors received on BGP peering sessions. Unknown .1.3.6.1.4.1.6027.20.1.4.2.11 |
f10BgpM2PeerGroupCore object types on BGP peering sessions. Unknown .1.3.6.1.4.1.6027.20.1.4.2.12 |
f10BgpM2PathAttributesGroupAttributes received on BGP peering sessions. Unknown .1.3.6.1.4.1.6027.20.1.4.2.13 |
f10BgpM2PeerConfigurationGroupConfiguration objects for BGP peers. Unknown .1.3.6.1.4.1.6027.20.1.4.2.14 |
f10BgpM2PeerRouteReflectorCfgGroupConfiguration objects for BGP peers that support route reflection. Unknown .1.3.6.1.4.1.6027.20.1.4.2.15 |
f10BgpM2PeerAsConfederationCfgGroupConfiguration objects for BGP peers that support BGP confederations. Unknown .1.3.6.1.4.1.6027.20.1.4.2.16 |
f10BgpM2MIBNotificationsGroupThis group contains objects for notifications supported by this mib module. Unknown .1.3.6.1.4.1.6027.20.1.4.2.17 |
f10BgpM2Rfc2545GroupThis group is required for peers that support exchanging of IPv6 NLRI per RFC 2545. Unknown .1.3.6.1.4.1.6027.20.1.4.2.18 |