EdgeSwitch-IPV6-LOOPBACK-MIB
The EdgeSwitch-IPV6-LOOPBACK-MIB enables management of IPv6 loopback interface configurations on Ubiquiti EdgeSwitch devices running FastPath firmware. This module specifically exposes metrics for IPv6 address assignment, interface status, and administrative state of loopback interfaces to facilitate remote network topology verification and address planning.
Imported Objects
Objects
7 total| Object Name |
|---|
fastPathIpv6LoopbackThe Ubiquiti Private MIB for FastPath Loopback IPV6 address configuration MODULE-IDENTITY .1.3.6.1.4.1.4413.1.1.23 |
agentLoopbackIpv6Group OBJECT IDENTIFIER .1.3.6.1.4.1.4413.1.1.23.1 |
agentLoopbackIpv6PrefixTableA table of the Ipv6 prefixes associated with loopback instances SEQUENCE OF AgentLoopbackIpv6PrefixEntry .1.3.6.1.4.1.4413.1.1.23.1.1 |
agentLoopbackIpv6PrefixEntry AgentLoopbackIpv6PrefixEntry .1.3.6.1.4.1.4413.1.1.23.1.1.1 |
agentLoopbackIpv6PrefixPrefixThe prefix associated with the loopback interface. The data type is used to model the Ipv6 address. It is a binary string of 16 octects in network byte-order. It specifies the IP address of loopback which will be in Ipv6 Format, generated using internal interface number. Ipv6AddressPrefix (IPV6-TC) .1.3.6.1.4.1.4413.1.1.23.1.1.1.1 |
agentLoopbackIpv6PrefixPrefixLenThe length of the prefix (in bits). InetAddressPrefixLength (INET-ADDRESS-MIB) .1.3.6.1.4.1.4413.1.1.23.1.1.1.2 |
agentLoopbackIpv6PrefixStatusStatus of this instance.Row can be added or deleted by setting the value to createAndGo/destroy active(1) - this Loopback instance is active createAndGo(4) - set to this value to create an instance destroy(6) - set to this value to delete an instancerw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.4413.1.1.23.1.1.1.3 |
More MIBs from Broadcom
Browse all BroadcomMIBs →SNMP MIB module
SNMP MIB module
The FASTPATH-ROUTING-MIB provides vendor-specific SNMP access to monitor and manage routing table entries, forwarding states, and interface statistics on Broadcom-based FastPath switching platforms. It exposes critical operational metrics including active route counts, protocol state transitions, and packet forwarding counters essential for troubleshooting Layer 3 forwarding performance on these proprietary hardware architectures.
The FASTPATH-QOS-DIFFSERV-PRIVATE-MIB enables monitoring and configuration of Quality of Service (QoS) Differentiated Services (DiffServ) policies, including traffic classification, marking, and queuing parameters, on Netgear FastPath-based networking hardware. This private module provides vendor-specific access to internal QoS state variables and counters that are not exposed in standard IETF DiffServ MIBs.
The EdgeSwitch-QOS-DIFFSERV-PRIVATE-MIB enables monitoring and configuration of Quality of Service (QoS) Differentiated Services (DiffServ) parameters, including traffic classification, queuing, and scheduling policies, on Ubiquiti EdgeSwitch hardware. This private MIB extension provides granular visibility into per-interface and per-queue traffic statistics and policy enforcement states not covered by standard DiffServ MIBs.
Standard SNMP MIB module defining data structures for QUANTA-LB6M-REF-MIB.