ETV-TT1260-MIB
Detailed view of the defined objects, syntax rules, and hierarchical paths.
481
Objects
Active
Status
4
Dependencies
Imported Objects
Objects
481 total| Object Name |
|---|
tt1260 OBJECT IDENTIFIER .1.3.6.1.4.1.562.3.1.200 |
RFC1155-SMI Unknown .1.3.6.1.4.1.562.3.1.200 |
configuration OBJECT IDENTIFIER .1.3.6.1.4.1.562.3.1.200.1 |
hostnameHostname of the receiver on the network.ro DisplayString .1.3.6.1.4.1.562.3.1.200.1.1 |
ipAddressIP address of the receiver on the network.ro IpAddress .1.3.6.1.4.1.562.3.1.200.1.2 |
subnetMaskSubnet mask of the network to which the receiver is connected.ro IpAddress .1.3.6.1.4.1.562.3.1.200.1.3 |
defaultGatewayIpAddressDefault gateway to which packets should be sent that are not destined
for the local network.ro IpAddress .1.3.6.1.4.1.562.3.1.200.1.4 |
dnsServerIpAddressIP address of the DNS server to used.ro IpAddress .1.3.6.1.4.1.562.3.1.200.1.5 |
unitIdElectronic Serial Number of this receiverro Uint16 .1.3.6.1.4.1.562.3.1.200.1.6 |
dateTimeDate and time from the receiver's real-time clock or input streamro OCTET STRING .1.3.6.1.4.1.562.3.1.200.1.7 |
serviceHealthValue indicating the health of the receiver. A combination of bits
as follows:
1 = video task failed
2 = audio1 task failed
4 = audio2 task failed
8 = service model builder task failed
16 = brain task failed
32 = indirectly monitored task failedro Uint16 .1.3.6.1.4.1.562.3.1.200.1.8 |
serialRemoteTypeMode of the serial remote-control interface:
ttv232 = Tandberg protocol over RS-232 (point to point)
nds232 = NDS remote protocol over RS-232 (point to point)
nds485 = NDS remote protocol over RS-485 (multi-drop)rw Enumeration .1.3.6.1.4.1.562.3.1.200.1.9 |
serialRemoteAddressThe address of this receiver when using NDS multi-drop protocolrw INTEGER .1.3.6.1.4.1.562.3.1.200.1.10 |
controlModeThe source of remote control of the TT1260:
fp = front panel buttons
serial = RS-232 / RS-485 serial
ncp = over-air using Director
snmp = via Ethernet using SNMP
web = via Ethernet using a Web Browser
This mode may always be written to using SNMPrw Enumeration .1.3.6.1.4.1.562.3.1.200.1.11 |
serviceTrackingModeControls the action if the selected service is no longer found in the
Transport Stream:
monitor = just reports Service Not Found
hunt = receiver will search the Transport Stream for other services
flush = reports service not found and flushes service component PIDsrw Enumeration .1.3.6.1.4.1.562.3.1.200.1.12 |
inputContent OBJECT IDENTIFIER .1.3.6.1.4.1.562.3.1.200.2 |
inNetworkInformation OBJECT IDENTIFIER .1.3.6.1.4.1.562.3.1.200.2.1 |
inTransportStreamIdThe Transport Stream Identifierro Uint16 .1.3.6.1.4.1.562.3.1.200.2.1.1 |
inNetworkIdThe Network Identifier from the NITro Uint16 .1.3.6.1.4.1.562.3.1.200.2.1.2 |
inOriginalNetworkIdThe Original Netwrk Identifier from the SDTro Uint16 .1.3.6.1.4.1.562.3.1.200.2.1.3 |
inSiTypeThe type of SI: DVB (European) or ATSC (American)ro Enumeration .1.3.6.1.4.1.562.3.1.200.2.1.4 |
inCaInformation OBJECT IDENTIFIER .1.3.6.1.4.1.562.3.1.200.2.2 |
inCaTableTable of CA systems carried in the Transport Stream SEQUENCE OF InCaEntry .1.3.6.1.4.1.562.3.1.200.2.2.1 |
inCaEntryRow in table of CA systems InCaEntry .1.3.6.1.4.1.562.3.1.200.2.2.1.1 |
inCaSystemIdCA System IDro Uint16 .1.3.6.1.4.1.562.3.1.200.2.2.1.1.1 |
inCaEmmPidPID number of EMMs for the current CA systemro PIDNumber .1.3.6.1.4.1.562.3.1.200.2.2.1.1.2 |
inCaDataData from the CA descriptor for the current CA systemro OCTET STRING .1.3.6.1.4.1.562.3.1.200.2.2.1.1.3 |
inCaMultipleServiceDescramblingTableMulti Service Descrambling control table SEQUENCE OF InCaMSD_entry .1.3.6.1.4.1.562.3.1.200.2.2.2 |
inCaMultidescrableEntryRow in table of MSD InCaMSD_entry .1.3.6.1.4.1.562.3.1.200.2.2.2.1 |
inCaMSD_IndexCA System IDro Uint16 .1.3.6.1.4.1.562.3.1.200.2.2.2.1.1 |
inCaMSD_Service_IDService IDrw Uint16 .1.3.6.1.4.1.562.3.1.200.2.2.2.1.2 |
inCaMSD_Service_NameName of the servicero DisplayString .1.3.6.1.4.1.562.3.1.200.2.2.2.1.3 |
inServiceTableTable of all services available in the Transport Stream SEQUENCE OF InServiceEntry .1.3.6.1.4.1.562.3.1.200.2.3 |
inServiceEntryNo description yet InServiceEntry .1.3.6.1.4.1.562.3.1.200.2.3.1 |
inServiceIdService IDro Uint16 .1.3.6.1.4.1.562.3.1.200.2.3.1.1 |
inServicePmtPidPID of the PMT for the servicero PIDNumber .1.3.6.1.4.1.562.3.1.200.2.3.1.2 |
inServiceNameName of the servicero DisplayString .1.3.6.1.4.1.562.3.1.200.2.3.1.3 |
inServiceProviderName of the service providerro DisplayString .1.3.6.1.4.1.562.3.1.200.2.3.1.4 |
inServiceTypeType of the service:
unknown - not defined in stream
video - TV service
audio - Radio service
data - Data-only service
mosaic -Mosaic service
other - none of the abovero Enumeration .1.3.6.1.4.1.562.3.1.200.2.3.1.5 |
selectedService OBJECT IDENTIFIER .1.3.6.1.4.1.562.3.1.200.2.4 |
selectedServiceReasonIndicates the means by which the current service was selectedro Enumeration .1.3.6.1.4.1.562.3.1.200.2.4.1 |
selectedServiceIdService ID of the desired service.
This object should be written to (SNMP Set) to select a servicerw Uint16 .1.3.6.1.4.1.562.3.1.200.2.4.2 |
selectedServiceNameName of the selected servicero DisplayString .1.3.6.1.4.1.562.3.1.200.2.4.3 |
selectedProviderNameName of the provider of the selected servicero DisplayString .1.3.6.1.4.1.562.3.1.200.2.4.4 |
selectedServiceTypeType of the selected service: unknown, video, audio, data, mosaic or
otherro Enumeration .1.3.6.1.4.1.562.3.1.200.2.4.5 |
selectedInSiFlagFlag indicating whether the selected service is described in the SI
dataro Enumeration .1.3.6.1.4.1.562.3.1.200.2.4.6 |
selectedServiceFoundIdService ID for the selected service - filled in when the service is
found.ro Uint16 .1.3.6.1.4.1.562.3.1.200.2.4.7 |
selectedServicePcrPidPID of the PCR for the selected servicero PIDNumber .1.3.6.1.4.1.562.3.1.200.2.4.8 |
selectedServiceComponentTableTable listing all the available components in the selected service SEQUENCE OF SelectedServiceComponentEntry .1.3.6.1.4.1.562.3.1.200.2.4.9 |
selectedServiceComponentEntryRow in component table SelectedServiceComponentEntry .1.3.6.1.4.1.562.3.1.200.2.4.9.1 |
selSrvComponentPidPID of the component streamro PIDNumber .1.3.6.1.4.1.562.3.1.200.2.4.9.1.1 |
selSrvComponentTypeType of the component streamro Enumeration .1.3.6.1.4.1.562.3.1.200.2.4.9.1.2 |
selectedServiceAudioExtTableTable listing extra information for the available audio components
in the selected service SEQUENCE OF SelectedServiceAudioExtEntry .1.3.6.1.4.1.562.3.1.200.2.4.10 |
selectedServiceAudioExtEntryRow with extra information for audio components SelectedServiceAudioExtEntry .1.3.6.1.4.1.562.3.1.200.2.4.10.1 |
selSrvAudioPidPID of the audio streamro PIDNumber .1.3.6.1.4.1.562.3.1.200.2.4.10.1.1 |
selSrvAudioFormatEncoding format of the audio streamro Enumeration .1.3.6.1.4.1.562.3.1.200.2.4.10.1.2 |
selSrvAudioLanguageFirst language of the audio streamro Enumeration .1.3.6.1.4.1.562.3.1.200.2.4.10.1.3 |
selSrvAudioLanguage2Second language of the audio streamro Enumeration .1.3.6.1.4.1.562.3.1.200.2.4.10.1.4 |
selectedServiceDVBsubExtTableTable listing extra information for the available DVB subtitle components
in the selected service SEQUENCE OF SelectedServiceDVBsubExtEntry .1.3.6.1.4.1.562.3.1.200.2.4.11 |
selectedServiceDVBsubExtEntryRow with extra information for DVB subtitle components SelectedServiceDVBsubExtEntry .1.3.6.1.4.1.562.3.1.200.2.4.11.1 |
selSrvDvbsubPidPID of the DVB subtitles streamro PIDNumber .1.3.6.1.4.1.562.3.1.200.2.4.11.1.1 |
selSrvDvbsubLanguageLanguage of the DVB subtitles streamro Enumeration .1.3.6.1.4.1.562.3.1.200.2.4.11.1.2 |
selSrvDvbsubTypeType of the DVB subtitles streamro Uint8 .1.3.6.1.4.1.562.3.1.200.2.4.11.1.3 |
selSrvDvbsubCompPageIdComposition Page ID for the DVB Subtitles streamro Uint16 .1.3.6.1.4.1.562.3.1.200.2.4.11.1.4 |
selSrvDvbsubAncPageIdAncillary Page ID for the DVB Subtitles streamro Uint16 .1.3.6.1.4.1.562.3.1.200.2.4.11.1.5 |
selectedComponents OBJECT IDENTIFIER .1.3.6.1.4.1.562.3.1.200.2.5 |
selectedVideo OBJECT IDENTIFIER .1.3.6.1.4.1.562.3.1.200.2.5.1 |
selVideoReasonIndicates the reason for the current video PID selection:
none = no selection
user-pid = PID overriden by user
user-si = PID selected manually by user from list in SI
auto-si = PID selected automatically from SIro Enumeration .1.3.6.1.4.1.562.3.1.200.2.5.1.1 |
selVideoPidPID of the selected video stream.
This object may be written to (SNMP Set) to select a PID manually,
overriding the SIrw PIDNumber .1.3.6.1.4.1.562.3.1.200.2.5.1.2 |
selectedAudio1 OBJECT IDENTIFIER .1.3.6.1.4.1.562.3.1.200.2.5.2 |
selAudio1ReasonIndicates the reason for the current audio1 PID selection:
none = no selection
user-pid = PID overriden by user
user-si = PID selected manually by user from list in SI
auto-si = PID selected automatically from SIro Enumeration .1.3.6.1.4.1.562.3.1.200.2.5.2.1 |
selAudio1PidPID of the selected audio1 stream.
This object may be written to (SNMP Set) to select a PID manually,
overriding the SIrw PIDNumber .1.3.6.1.4.1.562.3.1.200.2.5.2.2 |
selAudio1MpegLanguageNo description yetrw Enumeration .1.3.6.1.4.1.562.3.1.200.2.5.2.3 |
selAudio1MpegLanguage2No description yetrw Enumeration .1.3.6.1.4.1.562.3.1.200.2.5.2.4 |
selAudio1FormatNo description yetrw Enumeration .1.3.6.1.4.1.562.3.1.200.2.5.2.5 |
selectedAudio2 OBJECT IDENTIFIER .1.3.6.1.4.1.562.3.1.200.2.5.3 |
selAudio2ReasonIndicates the reason for the current audio2 PID selection:
none = no selection
user-pid = PID overriden by user
user-si = PID selected manually by user from list in SI
auto-si = PID selected automatically from SIro Enumeration .1.3.6.1.4.1.562.3.1.200.2.5.3.1 |
selAudio2PidPID of the selected audio2 stream.
This object may be written to (SNMP Set) to select a PID manually,
overriding the SIrw PIDNumber .1.3.6.1.4.1.562.3.1.200.2.5.3.2 |
selAudio2MpegLanguageNo description yetrw Enumeration .1.3.6.1.4.1.562.3.1.200.2.5.3.3 |
selAudio2MpegLanguage2No description yetrw Enumeration .1.3.6.1.4.1.562.3.1.200.2.5.3.4 |
selAudio2FormatNo description yetrw Enumeration .1.3.6.1.4.1.562.3.1.200.2.5.3.5 |
selectedLowSpeedData OBJECT IDENTIFIER .1.3.6.1.4.1.562.3.1.200.2.5.4 |
selLsdReasonIndicates the reason for the current low-speed data PID selection:
none = no selection
user-pid = PID overriden by user
user-si = PID selected manually by user from list in SI
auto-si = PID selected automatically from SIro Enumeration .1.3.6.1.4.1.562.3.1.200.2.5.4.1 |
selLsdPidPID of the selected low-speed data stream.
This object may be written to (SNMP Set) to select a PID manually,
overriding the SIrw PIDNumber .1.3.6.1.4.1.562.3.1.200.2.5.4.2 |
selectedHighSpeedData OBJECT IDENTIFIER .1.3.6.1.4.1.562.3.1.200.2.5.5 |
selHsdReasonIndicates the reason for the current high-speed data PID selection:
none = no selection
user-pid = PID overriden by user
user-si = PID selected manually by user from list in SI
auto-si = PID selected automatically from SIro Enumeration .1.3.6.1.4.1.562.3.1.200.2.5.5.1 |
selHsdPidPID of the selected high-speed data stream.
This object may be written to (SNMP Set) to select a PID manually,
overriding the SIrw PIDNumber .1.3.6.1.4.1.562.3.1.200.2.5.5.2 |
selectedVbi OBJECT IDENTIFIER .1.3.6.1.4.1.562.3.1.200.2.5.6 |
selVbiReasonIndicates the reason for the current VBI PID selection:
none = no selection
user-pid =PID overriden by user
user-si = PID selected manually by user from list in SI
auto-si = PID selected automatically from SIro Enumeration .1.3.6.1.4.1.562.3.1.200.2.5.6.1 |
selVbiPidPID of the selected VBI stream.
This object may be written to (SNMP Set) to select a PID manually,
overriding the SIrw PIDNumber .1.3.6.1.4.1.562.3.1.200.2.5.6.2 |
selectedDvbsub OBJECT IDENTIFIER .1.3.6.1.4.1.562.3.1.200.2.5.7 |
selDvbsubReasonIndicates the reason for the current DVB subtitles PID selection:
none = no selection
user-pid = PID overriden by user
user-si = PID selected manually by user from list in SI
auto-si = PID selected automatically from SIro Enumeration .1.3.6.1.4.1.562.3.1.200.2.5.7.1 |
selDvbsubPidPID of the selected DVB subtitles stream.
This object may be written to (SNMP Set) to select a PID manually,
overriding the SIrw PIDNumber .1.3.6.1.4.1.562.3.1.200.2.5.7.2 |
selectedTtxt OBJECT IDENTIFIER .1.3.6.1.4.1.562.3.1.200.2.5.8 |
selTtxtReasonIndicates the reason for the current teletext PID selection:
none = no selection
user-pid = PID overriden by user
user-si = PID selected manually by user from list in SI
auto-si = PID selected automatically from SIro Enumeration .1.3.6.1.4.1.562.3.1.200.2.5.8.1 |
selTtxtPidPID of the selected teletext stream.
This object may be written to (SNMP Set) to select a PID manually,
overriding the SIrw PIDNumber .1.3.6.1.4.1.562.3.1.200.2.5.8.2 |
selectedPcr OBJECT IDENTIFIER .1.3.6.1.4.1.562.3.1.200.2.5.9 |
selPcrReasonIndicates the reason for the current PCR PID selection:
none = no selection
user-pid =PID overriden by user
user-si = PID selected manually by user from list in SI
auto-si = PID selected automatically from SIro Enumeration .1.3.6.1.4.1.562.3.1.200.2.5.9.1 |
selPcrPidPID of the selected PCR stream.
This object may be written to (SNMP Set) to select a PID manually,
overriding the SIrw PIDNumber .1.3.6.1.4.1.562.3.1.200.2.5.9.2 |
selectedEtherHighSpeedData OBJECT IDENTIFIER .1.3.6.1.4.1.562.3.1.200.2.5.10 |
selEthHsdReasonIndicates the reason for the current ethernet high-speed data PID selection:
none =no selection
user-pid = PID overriden by user
user-si = PID selected manually by user from list in SI
auto-si = PID selected automatically from SIro Enumeration .1.3.6.1.4.1.562.3.1.200.2.5.10.1 |
selEthHsdPidPID of the selected ethernet high-speed data stream.
This object may be written to (SNMP Set) to select a PID manually,
overriding the SIrw PIDNumber .1.3.6.1.4.1.562.3.1.200.2.5.10.2 |
userSelectedComponents OBJECT IDENTIFIER .1.3.6.1.4.1.562.3.1.200.2.6 |
userVideoPidPID of the last user-selected video streamro PIDNumber .1.3.6.1.4.1.562.3.1.200.2.6.1 |
userAudio1 OBJECT IDENTIFIER .1.3.6.1.4.1.562.3.1.200.2.6.2 |
userAudio1PidPID of the last user-selected audio1 streamro PIDNumber .1.3.6.1.4.1.562.3.1.200.2.6.2.1 |
userAudio1FormatEncoding format of the last user-selected audio1 streamro Enumeration .1.3.6.1.4.1.562.3.1.200.2.6.2.2 |
userAudio2 OBJECT IDENTIFIER .1.3.6.1.4.1.562.3.1.200.2.6.3 |
userAudio2PidPID of the last user-selected audio2 streamro PIDNumber .1.3.6.1.4.1.562.3.1.200.2.6.3.1 |
userAudio2FormatEncoding format of the last user-selected audio2 streamro Enumeration .1.3.6.1.4.1.562.3.1.200.2.6.3.2 |
userLsdPidPID of the last user-selected low-speed data streamro PIDNumber .1.3.6.1.4.1.562.3.1.200.2.6.4 |
userHsdPidPID of the last user-selected high-speed data streamro PIDNumber .1.3.6.1.4.1.562.3.1.200.2.6.5 |
userVbiPidPID of the last user-selected VBI streamro PIDNumber .1.3.6.1.4.1.562.3.1.200.2.6.6 |
userTtxtPidPID of the last user-selected teletext streamro PIDNumber .1.3.6.1.4.1.562.3.1.200.2.6.7 |
userDvbsubPidPID of the last user-selected DVB subtitles streamro PIDNumber .1.3.6.1.4.1.562.3.1.200.2.6.8 |
userPcrPidPID of the last user-selected PCR streamro PIDNumber .1.3.6.1.4.1.562.3.1.200.2.6.9 |
userEtherHsdPidPID of the last user-selected high-speed data streamro PIDNumber .1.3.6.1.4.1.562.3.1.200.2.6.10 |
userLsdTypeFormat of the last user-selected low-speed data stream:
ttvFormat2 = TandbergTV Proprietry Format #2
dvbDataBroadcast = DVB Asynchronous Data Broadcast Formatro Enumeration .1.3.6.1.4.1.562.3.1.200.2.6.11 |
userLsdBaudIndicates the baud rate for the current low-speed data PID selection
if the current format is the DVB Asynchronous Data Broadcast Format:
baud1200 = 1200
baud2400 = 2400
baud4800 = 4800
baud9600 = 9600
baud19200 = 19200
baud38400 = 38400ro Enumeration .1.3.6.1.4.1.562.3.1.200.2.6.12 |
decoder OBJECT IDENTIFIER .1.3.6.1.4.1.562.3.1.200.3 |
video OBJECT IDENTIFIER .1.3.6.1.4.1.562.3.1.200.3.1 |
videoStatus OBJECT IDENTIFIER .1.3.6.1.4.1.562.3.1.200.3.1.1 |
videoStateCurrent state of the video: running, stopped, errorro Enumeration .1.3.6.1.4.1.562.3.1.200.3.1.1.1 |
videoHorizResHorizontal resolution of the video stream (pixels)ro Uint16 .1.3.6.1.4.1.562.3.1.200.3.1.1.2 |
videoVertResVertical resolution of the video stream (pixels)ro Uint16 .1.3.6.1.4.1.562.3.1.200.3.1.1.3 |
videoFrameRateFrame rate of the video streamro Enumeration .1.3.6.1.4.1.562.3.1.200.3.1.1.4 |
videoProfileProfile of the video stream: 4:2:0 or 4:2:2ro Enumeration .1.3.6.1.4.1.562.3.1.200.3.1.1.5 |
videoAspectRatioAspect ratio of the video streamro Enumeration .1.3.6.1.4.1.562.3.1.200.3.1.1.6 |
videoRateBufferLevelVideo rate buffer level, as a percentagero Uint16 .1.3.6.1.4.1.562.3.1.200.3.1.1.7 |
videoBitrateVideo bit rate, in bits/secondro Uint32 .1.3.6.1.4.1.562.3.1.200.3.1.1.8 |
videoFramesyncStatusLock status of the video frame syncro Enumeration .1.3.6.1.4.1.562.3.1.200.3.1.1.9 |
videoFramesyncSignalFlag indicating presence or absence of the video frame syncro Enumeration .1.3.6.1.4.1.562.3.1.200.3.1.1.10 |
videoAfdStateIndicates whether an Active Format Descriptor is presentro Enumeration .1.3.6.1.4.1.562.3.1.200.3.1.1.11 |
videoAfdValueValue sent in the Active Format Descriptorro INTEGER .1.3.6.1.4.1.562.3.1.200.3.1.1.12 |
videoSetup OBJECT IDENTIFIER .1.3.6.1.4.1.562.3.1.200.3.1.2 |
videoDefaultStandardDefault video output standard: NTSC 525lines or PAL 625 linesrw Enumeration .1.3.6.1.4.1.562.3.1.200.3.1.2.1 |
video525OutputStandardColour encoding standard for 525-line outputrw Enumeration .1.3.6.1.4.1.562.3.1.200.3.1.2.2 |
video625OutputStandardColour encoding standard for 625-line outputrw Enumeration .1.3.6.1.4.1.562.3.1.200.3.1.2.3 |
videoMonitorAspectRatioAspect ratio of the video output: 4x3 or 16x9rw Enumeration .1.3.6.1.4.1.562.3.1.200.3.1.2.4 |
videoStopModeOutput action when video not available:
freeze frame = keep showing last video frame
black = show frame of all black
nosync = turn off sync on outputrw Enumeration .1.3.6.1.4.1.562.3.1.200.3.1.2.5 |
videoTestPatternEnable and select a video test pattern to output:
0 = none
1 - 10 = PAL 625-line tests
11 - 20 = NTSC 525-line testsrw INTEGER .1.3.6.1.4.1.562.3.1.200.3.1.2.6 |
videoDelay4204:2:0 Video delay (ms)rw INTEGER .1.3.6.1.4.1.562.3.1.200.3.1.2.7 |
videoDelay4224:2:2 Video delay (ms)rw INTEGER .1.3.6.1.4.1.562.3.1.200.3.1.2.8 |
video525StartLineStart line for 525-line video: 22 or 23rw INTEGER .1.3.6.1.4.1.562.3.1.200.3.1.2.9 |
videoOutputLevelVideo output level (percent): 70 to 130rw INTEGER .1.3.6.1.4.1.562.3.1.200.3.1.2.10 |
videoOutputCalibrationVideo output level calibration offset (percent): 100 = normal
THIS IS A FACTORY-ONLY PARAMETER AND DOES NOT APPEAR
ON PRODUCTION UNITSrw Uint16 .1.3.6.1.4.1.562.3.1.200.3.1.2.11 |
videoOutputOffsetVideo output offset: 0 (min) to 255 (max)
THIS IS A FACTORY-ONLY PARAMETER AND DOES NOT APPEAR
ON PRODUCTION UNITSrw INTEGER .1.3.6.1.4.1.562.3.1.200.3.1.2.12 |
videoFramesyncEnableVideo Frame Sync (Genlock) disable/enablerw Enumeration .1.3.6.1.4.1.562.3.1.200.3.1.2.13 |
videoFramesyncOffsetPalVideo Frame Sync offset for PAL (-16384 to +16383)rw INTEGER (-16384..16383) .1.3.6.1.4.1.562.3.1.200.3.1.2.14 |
videoFramesyncOffsetNtscVideo Frame Sync offset for NTSC (-16384 to +16383)rw INTEGER (-16384..16383) .1.3.6.1.4.1.562.3.1.200.3.1.2.15 |
videoEdhEnableVideo Error Detection and Handling disable/enablerw Enumeration .1.3.6.1.4.1.562.3.1.200.3.1.2.16 |
videoEmbeddedAudioDidEmbedded Audio Data IDrw Enumeration .1.3.6.1.4.1.562.3.1.200.3.1.2.17 |
videoEmbeddedAudioChanEmbedded Audio Channelrw Enumeration .1.3.6.1.4.1.562.3.1.200.3.1.2.18 |
videoFrequencyVideo frequency (0 to 15, default 8)
THIS IS A FACTORY-ONLY PARAMETER AND DOES NOT APPEAR
ON PRODUCTION UNITSrw INTEGER .1.3.6.1.4.1.562.3.1.200.3.1.2.19 |
videoPTSConformanceWhen set to compliant, Synchronisation is strict (within 1 mS).
PTS stream must be linear, continous and jitter free.
When in non compliant mode synchronisation is less strict (as per user manual), but streams with poor
lineararity or discontinuities are tolleratedrw Enumeration .1.3.6.1.4.1.562.3.1.200.3.1.2.20 |
teletext OBJECT IDENTIFIER .1.3.6.1.4.1.562.3.1.200.3.2 |
teletextStatus OBJECT IDENTIFIER .1.3.6.1.4.1.562.3.1.200.3.2.1 |
teletextStateTeletext present/absentro Enumeration .1.3.6.1.4.1.562.3.1.200.3.2.1.1 |
teletextSetup OBJECT IDENTIFIER .1.3.6.1.4.1.562.3.1.200.3.2.2 |
vbi OBJECT IDENTIFIER .1.3.6.1.4.1.562.3.1.200.3.3 |
vbiStatus OBJECT IDENTIFIER .1.3.6.1.4.1.562.3.1.200.3.3.1 |
vbiStateShows whether a decoded VBI data stream is presentro Enumeration .1.3.6.1.4.1.562.3.1.200.3.3.1.1 |
vbiContent OBJECT IDENTIFIER .1.3.6.1.4.1.562.3.1.200.3.3.1.2 |
vbiContentCcvcVBI Closed Captioningro Enumeration .1.3.6.1.4.1.562.3.1.200.3.3.1.2.1 |
vbiContentWssVBI Wide Screen Signallingro Enumeration .1.3.6.1.4.1.562.3.1.200.3.3.1.2.2 |
vbiContentAmolVBI AMOL 1 & 2 Captioningro Enumeration .1.3.6.1.4.1.562.3.1.200.3.3.1.2.3 |
vbiContentVidxVBI Video Indexro Enumeration .1.3.6.1.4.1.562.3.1.200.3.3.1.2.4 |
vbiContentVpsVBI Video Programming Systemro Enumeration .1.3.6.1.4.1.562.3.1.200.3.3.1.2.5 |
vbiContentTtxtVBI Teletextro Enumeration .1.3.6.1.4.1.562.3.1.200.3.3.1.2.6 |
vbiContentVitsVBI Vertical Interval Test Signalro Enumeration .1.3.6.1.4.1.562.3.1.200.3.3.1.2.7 |
vbiContentGcrVBI Ghost Cancellation Referencero Enumeration .1.3.6.1.4.1.562.3.1.200.3.3.1.2.8 |
vbiContentVitcVBI Vertical Interval Time Codero Enumeration .1.3.6.1.4.1.562.3.1.200.3.3.1.2.9 |
vbiContentMonoVBI Monochrome 4:2:2 samplesro Enumeration .1.3.6.1.4.1.562.3.1.200.3.3.1.2.10 |
vbiContentNABTSVBI NABTS contentro Enumeration .1.3.6.1.4.1.562.3.1.200.3.3.1.2.11 |
vbiLinesTableTable listing the content of each VBI line SEQUENCE OF VbiLinesEntry .1.3.6.1.4.1.562.3.1.200.3.3.1.3 |
vbiLinesEntryNo description yet VbiLinesEntry .1.3.6.1.4.1.562.3.1.200.3.3.1.3.1 |
vbiLineVBI line numberro INTEGER .1.3.6.1.4.1.562.3.1.200.3.3.1.3.1.1 |
vbiLineContentsContents of VBI linero Enumeration .1.3.6.1.4.1.562.3.1.200.3.3.1.3.1.2 |
vbiSetup OBJECT IDENTIFIER .1.3.6.1.4.1.562.3.1.200.3.3.2 |
vbiEnableCcvcVBI Closed Captioning disable/enablerw Enumeration .1.3.6.1.4.1.562.3.1.200.3.3.2.1 |
vbiEnableWssVBI Wide Screen Signalling controlrw Enumeration .1.3.6.1.4.1.562.3.1.200.3.3.2.2 |
vbiEnableAmolVBI AMOL 1 & 2 Captioning disable/enablerw Enumeration .1.3.6.1.4.1.562.3.1.200.3.3.2.3 |
vbiEnableVidxVBI Video Index disable/enablerw Enumeration .1.3.6.1.4.1.562.3.1.200.3.3.2.4 |
vbiEnableVpsVBI Video Programming System disable/enablerw Enumeration .1.3.6.1.4.1.562.3.1.200.3.3.2.5 |
vbiEnableTtxtVBI Teletext disable/enablerw Enumeration .1.3.6.1.4.1.562.3.1.200.3.3.2.6 |
vbiEnableVitsVBI Vertical Interval Test Signal none/ccir(625)/fcc(525)rw Enumeration .1.3.6.1.4.1.562.3.1.200.3.3.2.7 |
vbiEnableGcrVBI Ghost Cancellation Reference disable/enablerw Enumeration .1.3.6.1.4.1.562.3.1.200.3.3.2.8 |
vbiEnableVitcVBI Vertical Interval Time Code none/GOP/PESrw Enumeration .1.3.6.1.4.1.562.3.1.200.3.3.2.9 |
vbiEnableMonoVBI Monochrome 4:2:2 samples disable/enablerw Enumeration .1.3.6.1.4.1.562.3.1.200.3.3.2.10 |
vbiVitc625Line1First line to carry VBI data in 625-line outputrw INTEGER .1.3.6.1.4.1.562.3.1.200.3.3.2.11 |
vbiVitc625Line2Second line to carry VBI data in 625-line outputrw INTEGER .1.3.6.1.4.1.562.3.1.200.3.3.2.12 |
vbiVitc525Line1First line to carry VBI data in 525-line outputrw INTEGER .1.3.6.1.4.1.562.3.1.200.3.3.2.13 |
vbiVitc525Line2Second line to carry VBI data in 525-line outputrw INTEGER .1.3.6.1.4.1.562.3.1.200.3.3.2.14 |
vbiEnablePedestalVBI Pedestal disable/enablerw Enumeration .1.3.6.1.4.1.562.3.1.200.3.3.2.15 |
vbiEnableNABTSVBI NABTSrw Enumeration .1.3.6.1.4.1.562.3.1.200.3.3.2.16 |
pcr OBJECT IDENTIFIER .1.3.6.1.4.1.562.3.1.200.3.4 |
pcrStatus OBJECT IDENTIFIER .1.3.6.1.4.1.562.3.1.200.3.4.1 |
pcrRecoveryStatusShows whether a PCR was found in the incoming signalro Enumeration .1.3.6.1.4.1.562.3.1.200.3.4.1.1 |
audio OBJECT IDENTIFIER .1.3.6.1.4.1.562.3.1.200.3.5 |
audioStatusTableTwo-row table with information about decoded audio1 and audio2 SEQUENCE OF AudioStatusEntry .1.3.6.1.4.1.562.3.1.200.3.5.1 |
audioStatusEntryNo description yet AudioStatusEntry .1.3.6.1.4.1.562.3.1.200.3.5.1.1 |
audioStatusIndexSpecifies the audio channel the row is forro Enumeration .1.3.6.1.4.1.562.3.1.200.3.5.1.1.1 |
audioStateCurrent state of the audio: running, stopped or errorro Enumeration .1.3.6.1.4.1.562.3.1.200.3.5.1.1.2 |
audioSampleRateSample rate of the audio stream (units = 100Hz)ro Uint16 .1.3.6.1.4.1.562.3.1.200.3.5.1.1.3 |
audioBitrateBit rate of the audio stream (kbit/s)ro Uint16 .1.3.6.1.4.1.562.3.1.200.3.5.1.1.4 |
audioCodingStandardCoding Standard (Format) of the audio stream: none, mpeg2, ac3 or linearro Enumeration .1.3.6.1.4.1.562.3.1.200.3.5.1.1.5 |
audioMpegLayerMPEG Layer of the audio stream: layer 1 or layer 2ro Enumeration .1.3.6.1.4.1.562.3.1.200.3.5.1.1.6 |
audioMpegModeMPEG Mode of the audio stream: stereo, joint stereo, dual channel or
single channelro Enumeration .1.3.6.1.4.1.562.3.1.200.3.5.1.1.7 |
audioSetupTableTwo-row table for configuration of decoded audio1 and audio2 SEQUENCE OF AudioSetupEntry .1.3.6.1.4.1.562.3.1.200.3.5.2 |
audioSetupEntryNo description yet AudioSetupEntry .1.3.6.1.4.1.562.3.1.200.3.5.2.1 |
audioSetupIndexSpecifies the audio channel the row is forro Enumeration .1.3.6.1.4.1.562.3.1.200.3.5.2.1.1 |
audioOutputTypeAudio output type:analogue, consumer-grade iec958 digital, professional-grade
iec958 digital or consumer iec958 with Dolby ac3rw Enumeration .1.3.6.1.4.1.562.3.1.200.3.5.2.1.2 |
audioOutputRoutingAudio output routing: normal stereo, mono to L+R, mono to L only, mono
to R onlyrw Enumeration .1.3.6.1.4.1.562.3.1.200.3.5.2.1.3 |
audioClippingLevelAudio output clipping level (12 to 24 dB)rw INTEGER .1.3.6.1.4.1.562.3.1.200.3.5.2.1.4 |
audioDownmixModeAudio stereo downmix mode:surround stereo or normal stereorw Enumeration .1.3.6.1.4.1.562.3.1.200.3.5.2.1.5 |
audioPtsAdjustmentAudio PTS (synchronisation) adjustment (-495 to +495, in steps of 5,
units = 0.1ms)rw INTEGER (-495..495) .1.3.6.1.4.1.562.3.1.200.3.5.2.1.6 |
audioCalibrationLevelAudio calibration level (-50 to +40, units unknown)
THIS IS A FACTORY-ONLY PARAMETER AND DOES NOT APPEAR
ON PRODUCTION UNITSrw INTEGER (-50..40) .1.3.6.1.4.1.562.3.1.200.3.5.2.1.7 |
data OBJECT IDENTIFIER .1.3.6.1.4.1.562.3.1.200.3.6 |
async OBJECT IDENTIFIER .1.3.6.1.4.1.562.3.1.200.3.6.1 |
asyncStatus OBJECT IDENTIFIER .1.3.6.1.4.1.562.3.1.200.3.6.1.1 |
asyncStateShows whether an Async stream (low-speed data) is presentro Enumeration .1.3.6.1.4.1.562.3.1.200.3.6.1.1.1 |
asyncRateThe data rate of the Async low-speed data (bits/sec)ro Uint16 .1.3.6.1.4.1.562.3.1.200.3.6.1.1.2 |
asyncSetup OBJECT IDENTIFIER .1.3.6.1.4.1.562.3.1.200.3.6.1.2 |
asyncEnableAsync low-speed data disable/enablerw Enumeration .1.3.6.1.4.1.562.3.1.200.3.6.1.2.1 |
sync OBJECT IDENTIFIER .1.3.6.1.4.1.562.3.1.200.3.6.2 |
syncStatus OBJECT IDENTIFIER .1.3.6.1.4.1.562.3.1.200.3.6.2.1 |
syncStateShows whether a Sync stream (high-speed data) is runningro Enumeration .1.3.6.1.4.1.562.3.1.200.3.6.2.1.1 |
syncRateThe data rate of the Sync high-speed data (bits/sec)ro Uint16 .1.3.6.1.4.1.562.3.1.200.3.6.2.1.2 |
syncCardFittedShows whether a Sync data card is fittedro Enumeration .1.3.6.1.4.1.562.3.1.200.3.6.2.1.3 |
syncPresentShows whether a Sync stream (high-speed data) is presentro Enumeration .1.3.6.1.4.1.562.3.1.200.3.6.2.1.4 |
syncSetup OBJECT IDENTIFIER .1.3.6.1.4.1.562.3.1.200.3.6.2.2 |
syncEnableSync high-speed data disable/enablerw Enumeration .1.3.6.1.4.1.562.3.1.200.3.6.2.2.1 |
etherHsd OBJECT IDENTIFIER .1.3.6.1.4.1.562.3.1.200.3.6.3 |
etherHsdStatus OBJECT IDENTIFIER .1.3.6.1.4.1.562.3.1.200.3.6.3.1 |
etherHsdStateShows whether an Ethernet high-speed data stream is runningro Enumeration .1.3.6.1.4.1.562.3.1.200.3.6.3.1.1 |
etherHsdRateThe data rate of the Ethernet high-speed data (bits/sec)ro Uint32 .1.3.6.1.4.1.562.3.1.200.3.6.3.1.2 |
etherHsdLostPacketsCumulative number of packets lost for Ethernet high-speed dataro Uint16 .1.3.6.1.4.1.562.3.1.200.3.6.3.1.3 |
etherHsdLostFramesCumulative number of frames lost for Ethernet high-speed dataro Uint16 .1.3.6.1.4.1.562.3.1.200.3.6.3.1.4 |
etherHsdSetup OBJECT IDENTIFIER .1.3.6.1.4.1.562.3.1.200.3.6.3.2 |
etherHsdEnableEthernet high-speed data disable/enablerw Enumeration .1.3.6.1.4.1.562.3.1.200.3.6.3.2.1 |
etherHsdGatewayEnableEthernet high-speed data gateway disable/enablerw Enumeration .1.3.6.1.4.1.562.3.1.200.3.6.3.2.2 |
etherHsdGatewayIpAddressEthernet high-speed data gateway IP addressrw IpAddress .1.3.6.1.4.1.562.3.1.200.3.6.3.2.3 |
etherHsdEncapsulationEthernet high-speed data encapsulation type:Data piping / MPErw Enumeration .1.3.6.1.4.1.562.3.1.200.3.6.3.2.4 |
ca OBJECT IDENTIFIER .1.3.6.1.4.1.562.3.1.200.3.7 |
caStatus OBJECT IDENTIFIER .1.3.6.1.4.1.562.3.1.200.3.7.1 |
caStateShows whether CA data is present in the decoded streamro Enumeration .1.3.6.1.4.1.562.3.1.200.3.7.1.1 |
caSystemIdThe CA System IDro Uint16 .1.3.6.1.4.1.562.3.1.200.3.7.1.2 |
caStatusRas OBJECT IDENTIFIER .1.3.6.1.4.1.562.3.1.200.3.7.1.3 |
caRasDetectedRAS1 CA detected in the input streamro Enumeration .1.3.6.1.4.1.562.3.1.200.3.7.1.3.1 |
caStatusTtvSigProt OBJECT IDENTIFIER .1.3.6.1.4.1.562.3.1.200.3.7.1.4 |
caTtvSigProtDetectedTTV Signal Protection CA detected in the input streamro Enumeration .1.3.6.1.4.1.562.3.1.200.3.7.1.4.1 |
caStatusCommonInterface OBJECT IDENTIFIER .1.3.6.1.4.1.562.3.1.200.3.7.1.5 |
caCommonInterfaceDetectedCommon Interface CA detected in the input streamro Enumeration .1.3.6.1.4.1.562.3.1.200.3.7.1.5.1 |
caCommonInterfaceNameName of Common Interface CA modulero DisplayString .1.3.6.1.4.1.562.3.1.200.3.7.1.5.2 |
caCommonInterfaceStatusStatus of Common Interface CA modulero Enumeration .1.3.6.1.4.1.562.3.1.200.3.7.1.5.3 |
caStatusVideoguard OBJECT IDENTIFIER .1.3.6.1.4.1.562.3.1.200.3.7.1.6 |
caVideoguardDetectedVideoguard CA detected in the input streamro Enumeration .1.3.6.1.4.1.562.3.1.200.3.7.1.6.1 |
caVerifierVersionVersion number of Videoguard CA Verifierro Uint16 .1.3.6.1.4.1.562.3.1.200.3.7.1.6.2 |
caStatusBiss OBJECT IDENTIFIER .1.3.6.1.4.1.562.3.1.200.3.7.1.7 |
caBissDetectedBISS CA detected in the input streamro Enumeration .1.3.6.1.4.1.562.3.1.200.3.7.1.7.1 |
caStatusDirector5 OBJECT IDENTIFIER .1.3.6.1.4.1.562.3.1.200.3.7.1.8 |
caDirector5DetectedDirector 5 TTVCA detected in the input streamro Enumeration .1.3.6.1.4.1.562.3.1.200.3.7.1.8.1 |
caDirector5UniqueIdDirector 5 TTVCA unique hardware IDro DisplayString .1.3.6.1.4.1.562.3.1.200.3.7.1.8.2 |
caDirector5AuthorisationDirector 5 TTVCA authorisation statusro Enumeration .1.3.6.1.4.1.562.3.1.200.3.7.1.8.3 |
caSetup OBJECT IDENTIFIER .1.3.6.1.4.1.562.3.1.200.3.7.2 |
caSetupRas OBJECT IDENTIFIER .1.3.6.1.4.1.562.3.1.200.3.7.2.1 |
caRasDsngKey32-bit Scrambling Key for RAS CA in DSNG mode (0 to 99999999)rw INTEGER .1.3.6.1.4.1.562.3.1.200.3.7.2.1.1 |
caRasModeRAS Mode: fixed-key or DSNG moderw Enumeration .1.3.6.1.4.1.562.3.1.200.3.7.2.1.2 |
caSetupTtvSigProt OBJECT IDENTIFIER .1.3.6.1.4.1.562.3.1.200.3.7.2.2 |
caTtvSigProtEnableTTV Signal Protection CA disable/enablerw Enumeration .1.3.6.1.4.1.562.3.1.200.3.7.2.2.1 |
caTtvSigProtKeyTTV Signal Protection CA Key (not yet used)rw Uint32 .1.3.6.1.4.1.562.3.1.200.3.7.2.2.2 |
caSetupCommonInterface OBJECT IDENTIFIER .1.3.6.1.4.1.562.3.1.200.3.7.2.3 |
caSetupVideoguard OBJECT IDENTIFIER .1.3.6.1.4.1.562.3.1.200.3.7.2.4 |
caSetupBiss OBJECT IDENTIFIER .1.3.6.1.4.1.562.3.1.200.3.7.2.5 |
caBissKey48-bit key for BISS CA in Unscrambled Key Mode.
Reads as zero-length, since BISS prohibits reading back the key.rw OCTET STRING .1.3.6.1.4.1.562.3.1.200.3.7.2.5.1 |
caBissEncryptedKey64-bit encrypted key for BISS CA in Scrambled Key Mode (BISS-E).
Reads as zero-length, since BISS prohibits reading back the key.rw OCTET STRING .1.3.6.1.4.1.562.3.1.200.3.7.2.5.2 |
caBissModeEncryption Mode for the BISS Key (none, fixed-key, ttv-mode, encrypted
with userid1, encrypted with userid2)rw Enumeration .1.3.6.1.4.1.562.3.1.200.3.7.2.5.3 |
caBissUserid156-bit userid for encrypting BISS Key in user1 mode.
Reads as zero-length, since BISS prohibits reading back the ID.rw OCTET STRING .1.3.6.1.4.1.562.3.1.200.3.7.2.5.4 |
caBissUserid256-bit userid for encrypting BISS Key in user2 mode.
Reads as zero-length, since BISS prohibits reading back the ID.rw OCTET STRING .1.3.6.1.4.1.562.3.1.200.3.7.2.5.5 |
input OBJECT IDENTIFIER .1.3.6.1.4.1.562.3.1.200.4 |
inputStatus OBJECT IDENTIFIER .1.3.6.1.4.1.562.3.1.200.4.1 |
inputTsLockStateIndicates whether input is locked to a Transport Streamro Enumeration .1.3.6.1.4.1.562.3.1.200.4.1.1 |
inputTsPacketLengthPacket length of input Transport Stream (bytes)ro Uint16 .1.3.6.1.4.1.562.3.1.200.4.1.2 |
inputTsBitrateBit rate of input Transport Stream (bits/sec)ro Uint32 .1.3.6.1.4.1.562.3.1.200.4.1.3 |
inputBerLevelBit Error Rate of input signal (units = 1E-9)ro Uint32 .1.3.6.1.4.1.562.3.1.200.4.1.4 |
inputMerLevelModulation Error Ratio of input signalro Uint32 .1.3.6.1.4.1.562.3.1.200.4.1.5 |
inputCardTypeType of input card fitted: unknown/none, ASI, QPSK, MCD, OFDM, QAM(Newtec),
G703, G037 (IP), ATM_E3, ATM_DS3, SAT_HD, SAT_QPSK_ASI, G037_PRO, SAT_S2, EURO_S2 Variantsro Enumeration .1.3.6.1.4.1.562.3.1.200.4.1.6 |
inputCardRetuneTypeType of input card fitted (according to retune parameters): unknown/none,
ASI, QPSK, MCD, OFDM, QAM(Newtec), G703, G037 (IP), ATM_E3, ATM_DS3,
SAT_HD, SAT_QPSK_ASI, G037_PRO, SAT_S2, EURO_S2 Variantsro Enumeration .1.3.6.1.4.1.562.3.1.200.4.1.7 |
inputPerLevelPre-Viterbi Error Ratio of input signalro Uint32 .1.3.6.1.4.1.562.3.1.200.4.1.8 |
inputSetup OBJECT IDENTIFIER .1.3.6.1.4.1.562.3.1.200.4.2 |
inputCards OBJECT IDENTIFIER .1.3.6.1.4.1.562.3.1.200.4.3 |
inputRetuneStateThis variable is no longer usedrw INTEGER .1.3.6.1.4.1.562.3.1.200.4.3.1 |
inputCardAsi OBJECT IDENTIFIER .1.3.6.1.4.1.562.3.1.200.4.3.2 |
inputCardAsiStatus OBJECT IDENTIFIER .1.3.6.1.4.1.562.3.1.200.4.3.2.1 |
inputCardAsiLastlockedIndicates to which of the two inputs the ASI card last lockedro Enumeration .1.3.6.1.4.1.562.3.1.200.4.3.2.1.1 |
inputCardAsiSetup OBJECT IDENTIFIER .1.3.6.1.4.1.562.3.1.200.4.3.2.2 |
inputCardAsiInputSelectSpecifies on which of the two inputs the ASI card should look for a
Transport Stream, or that it should automatically select one.rw Enumeration .1.3.6.1.4.1.562.3.1.200.4.3.2.2.1 |
inputCardSat OBJECT IDENTIFIER .1.3.6.1.4.1.562.3.1.200.4.3.3 |
inputCardSatStatus OBJECT IDENTIFIER .1.3.6.1.4.1.562.3.1.200.4.3.3.1 |
inSatBerMeasurementBit Error Rate measurement (units = 1E-9)ro Uint32 .1.3.6.1.4.1.562.3.1.200.4.3.3.1.1 |
inSatEbn0MarginEb/N0 margin (units = 0.01dB)ro Uint32 .1.3.6.1.4.1.562.3.1.200.4.3.3.1.2 |
inSatDecoderSyncIndicates whether the satellite input is synchronisedro Enumeration .1.3.6.1.4.1.562.3.1.200.4.3.3.1.3 |
inSatQpskExtraStatus OBJECT IDENTIFIER .1.3.6.1.4.1.562.3.1.200.4.3.3.1.4 |
inQpskStatusRfLevelQPSK Input RF level (0 to 255)ro Uint32 .1.3.6.1.4.1.562.3.1.200.4.3.3.1.4.1 |
inQpskStatusLockStatus OBJECT IDENTIFIER .1.3.6.1.4.1.562.3.1.200.4.3.3.1.4.2 |
inQpskStatusLockFullInput fully lockedro Enumeration .1.3.6.1.4.1.562.3.1.200.4.3.3.1.4.2.1 |
inQpskStatusLockViterbiInput viterbi lockro Enumeration .1.3.6.1.4.1.562.3.1.200.4.3.3.1.4.2.2 |
inQpskStatusLockPhaseInput phase lockro Enumeration .1.3.6.1.4.1.562.3.1.200.4.3.3.1.4.2.3 |
inQpskStatusLockS2Input s2 lockro Enumeration .1.3.6.1.4.1.562.3.1.200.4.3.3.1.4.2.4 |
inQpskStatusLockS3Input s3 lockro Enumeration .1.3.6.1.4.1.562.3.1.200.4.3.3.1.4.2.5 |
inQpskStatusLockedFrequencyLocked frequency (kHz)ro Uint32 .1.3.6.1.4.1.562.3.1.200.4.3.3.1.4.3 |
inQpskStatusBerBit Error Rate (pre-viterbi) (units = 1E-9)ro Uint32 .1.3.6.1.4.1.562.3.1.200.4.3.3.1.4.4 |
inQpskStatusPostBerBit Error Rate (post-viterbi) (units = 1E-9)ro Uint32 .1.3.6.1.4.1.562.3.1.200.4.3.3.1.4.5 |
inQpskStatusSnrSignal to Noise Ratioro Uint32 .1.3.6.1.4.1.562.3.1.200.4.3.3.1.4.6 |
inQpskStatusEbn0Eb/N0 (units = 0.01dB)ro Uint32 .1.3.6.1.4.1.562.3.1.200.4.3.3.1.4.7 |
inQpskStatusEbn0MarginEb/N0 margin (units = 0.01dB)ro Uint32 .1.3.6.1.4.1.562.3.1.200.4.3.3.1.4.8 |
inQpskStatusRsCorrectedErrsNumber of Reed-Solomon corrected errorsro Uint32 .1.3.6.1.4.1.562.3.1.200.4.3.3.1.4.9 |
inQpskStatusRsUncorrectedErrsNumber of Reed-Solomon uncorrected errorsro Uint32 .1.3.6.1.4.1.562.3.1.200.4.3.3.1.4.10 |
inQpskStatusCarrierFrequency(Not yet used in the TT1260)ro Uint32 .1.3.6.1.4.1.562.3.1.200.4.3.3.1.4.11 |
inSatQamExtraStatus OBJECT IDENTIFIER .1.3.6.1.4.1.562.3.1.200.4.3.3.1.5 |
inQamStatusDecoderSyncDecoder synchronisation statero INTEGER .1.3.6.1.4.1.562.3.1.200.4.3.3.1.5.1 |
inQamStatusReceiveLevelReceive level (units = 0.01dBm)ro INTEGER .1.3.6.1.4.1.562.3.1.200.4.3.3.1.5.2 |
inQamStatusCoLevel(Not yet used in the TT1260)ro INTEGER .1.3.6.1.4.1.562.3.1.200.4.3.3.1.5.3 |
inQamStatusEbn0EstEb/N0 estimate (units = 0.01dB)ro INTEGER .1.3.6.1.4.1.562.3.1.200.4.3.3.1.5.4 |
inQamStatusCarrierFreqOffsetCarrier frequency offset (Hz)ro INTEGER .1.3.6.1.4.1.562.3.1.200.4.3.3.1.5.5 |
inQamStatusSymbolRateOffset(Not yet used in the TT1260)ro INTEGER .1.3.6.1.4.1.562.3.1.200.4.3.3.1.5.6 |
inQamStatusByteErrorRate(Not yet used in the TT1260)ro INTEGER .1.3.6.1.4.1.562.3.1.200.4.3.3.1.5.7 |
inQamStatusPrbsErrorRate(Not yet used in the TT1260)ro INTEGER .1.3.6.1.4.1.562.3.1.200.4.3.3.1.5.8 |
inQamStatusBerBit Error Rate (units = 1E-9)ro INTEGER .1.3.6.1.4.1.562.3.1.200.4.3.3.1.5.9 |
inQamStatusUncorrectedPacketsNumber of Reed-Solomon uncorrected errorsro INTEGER .1.3.6.1.4.1.562.3.1.200.4.3.3.1.5.10 |
inQamStatusDeviceId(Not yet used in the TT1260)ro INTEGER .1.3.6.1.4.1.562.3.1.200.4.3.3.1.5.11 |
inQamStatusAlarmsWord(Not yet used in the TT1260)ro INTEGER .1.3.6.1.4.1.562.3.1.200.4.3.3.1.5.12 |
inSatS2ExtraStatus OBJECT IDENTIFIER .1.3.6.1.4.1.562.3.1.200.4.3.3.1.6 |
inS2StatusFecRateS2 card FEC rate: none, 1-2, 2-3, 3-4, 5-6, 6-7, 7-8, 8-9, auto,
1-4, 1-3, 2-5, 3-5, 4-5, 9-10ro Enumeration .1.3.6.1.4.1.562.3.1.200.4.3.3.1.6.1 |
inS2StatusModulationTypeS2 card Modulation type: BPSK, QPSK, 8PSK, 16QAM, auto, 16SQAM, auto dvb-s2ro Enumeration .1.3.6.1.4.1.562.3.1.200.4.3.3.1.6.2 |
inS2StatusCNRatioS2 card Signal to Noise ratio (units = 0.01dB)ro INTEGER .1.3.6.1.4.1.562.3.1.200.4.3.3.1.6.3 |
inS2StatusRfLevelS2 card Input RF level (dBm)ro INTEGER .1.3.6.1.4.1.562.3.1.200.4.3.3.1.6.4 |
inputCardSatSetup OBJECT IDENTIFIER .1.3.6.1.4.1.562.3.1.200.4.3.3.2 |
inSatSetupInputSelectSelection of input 1, 2, 3, 4, 5 or 6 on satellite cardrw Enumeration .1.3.6.1.4.1.562.3.1.200.4.3.3.2.1 |
inSatSetupInputTableNo description yet SEQUENCE OF InSatSetupInputEntry .1.3.6.1.4.1.562.3.1.200.4.3.3.2.2 |
inSatSetupInputEntryNo description yet InSatSetupInputEntry .1.3.6.1.4.1.562.3.1.200.4.3.3.2.2.1 |
inSatSetupInputIndexNo description yetro INTEGER .1.3.6.1.4.1.562.3.1.200.4.3.3.2.2.1.1 |
inSatSetupSymbolRateSatellite symbol rate (bits/sec)rw INTEGER .1.3.6.1.4.1.562.3.1.200.4.3.3.2.2.1.2 |
inSatSetupFecRateSatellite FEC rate: none, 1-2, 2-3, 3-4, 5-6, 6-7, 7-8, 8-9, autorw Enumeration .1.3.6.1.4.1.562.3.1.200.4.3.3.2.2.1.3 |
inSatSetupTuneFrequencyTune frequency (kHz)rw INTEGER .1.3.6.1.4.1.562.3.1.200.4.3.3.2.2.1.4 |
inSatSetupSatelliteFrequencySatellite frequency (kHz)rw Uint32 .1.3.6.1.4.1.562.3.1.200.4.3.3.2.2.1.5 |
inSatSetupLnbFrequencyLNB frequency (kHz)rw Uint32 .1.3.6.1.4.1.562.3.1.200.4.3.3.2.2.1.6 |
inSatSetupSearchRangeSatellite search range (kHz)rw Uint32 .1.3.6.1.4.1.562.3.1.200.4.3.3.2.2.1.7 |
inSatSetupPolarizationSatellite polarization: vertical, horizontalrw Enumeration .1.3.6.1.4.1.562.3.1.200.4.3.3.2.2.1.8 |
inSatSetupModulationTypeSatellite modulation type: BPSK, QPSK, 8PSK, 16QAM, auto, 16SQAM, auto( dvb-s2 )rw Enumeration .1.3.6.1.4.1.562.3.1.200.4.3.3.2.2.1.9 |
inSatSetupLnbVoltageLNB voltage off/onrw Enumeration .1.3.6.1.4.1.562.3.1.200.4.3.3.2.2.1.10 |
inSatSetupLnb22khzLNB 22kHz disabled/enabledrw Enumeration .1.3.6.1.4.1.562.3.1.200.4.3.3.2.2.1.11 |
inSatSetupLnbBoostLNB Boost disabled/enabledrw Enumeration .1.3.6.1.4.1.562.3.1.200.4.3.3.2.2.1.12 |
inSatSetupSpectrumSenseSatellite spectrum sensing: auto, normal, invertedrw Enumeration .1.3.6.1.4.1.562.3.1.200.4.3.3.2.2.1.13 |
inSatSetupGainSelectSatellite gain selection: normal, highrw Enumeration .1.3.6.1.4.1.562.3.1.200.4.3.3.2.2.1.14 |
inSatSetupRollOffSatellite roll-off: roll20=20%, roll35=35%, roll25=25%rw Enumeration .1.3.6.1.4.1.562.3.1.200.4.3.3.2.2.1.15 |
inSatSetupModulationModeSatellite modulation mode: dvbs, dvb-s2rw Enumeration .1.3.6.1.4.1.562.3.1.200.4.3.3.2.2.1.16 |
inSatSetupOutputModeSatellite output mode: normal, constellationrw Enumeration .1.3.6.1.4.1.562.3.1.200.4.3.3.2.2.1.17 |
inputCardOfdm OBJECT IDENTIFIER .1.3.6.1.4.1.562.3.1.200.4.3.4 |
inputCardOfdmStatus OBJECT IDENTIFIER .1.3.6.1.4.1.562.3.1.200.4.3.4.1 |
inOfdmStatusSignalLockOFDM signal lock status: unlocked, lockedro Enumeration .1.3.6.1.4.1.562.3.1.200.4.3.4.1.1 |
inOfdmStatusMerValueOFDM MER value: 0.00 to 64.00 (units = 0.01)ro INTEGER .1.3.6.1.4.1.562.3.1.200.4.3.4.1.2 |
inOfdmStatusMerValidIndicates that the MER value is valid.ro Enumeration .1.3.6.1.4.1.562.3.1.200.4.3.4.1.3 |
inOfdmStatusPostViterbiBerOFDM post-viterbi Bit Error Rate (post viterbi) (units = 1E-9)ro Uint32 .1.3.6.1.4.1.562.3.1.200.4.3.4.1.4 |
inOfdmStatusPostRsErrorsOFDM post-viterbi Reed-Solomon errorsro Uint32 .1.3.6.1.4.1.562.3.1.200.4.3.4.1.5 |
inOfdmStatusGuardIntervalOFDM Guard Interval: 1/32, 1/16, 1/8, 1/4ro Enumeration .1.3.6.1.4.1.562.3.1.200.4.3.4.1.6 |
inOfdmStatusCarrierModeOFDM Carrier Mode: 2K, 8Kro Enumeration .1.3.6.1.4.1.562.3.1.200.4.3.4.1.7 |
inOfdmStatusSpectrumInvertOFDM Spectrum Inversion: normal, invertedro Enumeration .1.3.6.1.4.1.562.3.1.200.4.3.4.1.8 |
inOfdmStatusHierarchyTypeOFDM Hierarchy Type: none, alpha 1, alpha 2, alpha 4ro Enumeration .1.3.6.1.4.1.562.3.1.200.4.3.4.1.9 |
inOfdmStatusModulationModeOFDM Modulation Mode: none, QPSK, 16QAM, 64QAMro Enumeration .1.3.6.1.4.1.562.3.1.200.4.3.4.1.10 |
inOfdmStatusHighCodeRateOFDM High FEC Rate:none, 1/2, 2/3, 3/4, 5/6, 7/8ro Enumeration .1.3.6.1.4.1.562.3.1.200.4.3.4.1.11 |
inOfdmStatusLowCodeRateOFDM Low FEC Rate: none, 1/2, 2/3, 3/4, 5/6, 7/8ro Enumeration .1.3.6.1.4.1.562.3.1.200.4.3.4.1.12 |
inOfdmStatusSupportedFeatures OBJECT IDENTIFIER .1.3.6.1.4.1.562.3.1.200.4.3.4.1.13 |
inOfdmStatusSoftwareVersionOFDM card software versionro Uint32 .1.3.6.1.4.1.562.3.1.200.4.3.4.1.13.1 |
inOfdmStatusHardwareVersionOFDM card hardware versionro Uint32 .1.3.6.1.4.1.562.3.1.200.4.3.4.1.13.2 |
inOfdmStatusFeatureChanSp6MHzOFDM card 6MHz channel spacing:unsupported, supportedro Enumeration .1.3.6.1.4.1.562.3.1.200.4.3.4.1.13.3 |
inOfdmStatusFeatureChanSp7MHzOFDM card 7MHz channel spacing:unsupported, supportedro Enumeration .1.3.6.1.4.1.562.3.1.200.4.3.4.1.13.4 |
inOfdmStatusFeatureChanSp8MHzOFDM card 8MHz channel spacing:unsupported, supportedro Enumeration .1.3.6.1.4.1.562.3.1.200.4.3.4.1.13.5 |
inOfdmStatusFeatureChanSp12MHzOFDM card 12MHz channel spacing:unsupported, supportedro Enumeration .1.3.6.1.4.1.562.3.1.200.4.3.4.1.13.6 |
inOfdmStatusFeatureCarrier2kOFDM card carrier 2K: unsupported, supportedro Enumeration .1.3.6.1.4.1.562.3.1.200.4.3.4.1.13.7 |
inOfdmStatusFeatureCarrier8kOFDM card carrier 8K: unsupported, supportedro Enumeration .1.3.6.1.4.1.562.3.1.200.4.3.4.1.13.8 |
inOfdmStatusFeatureStep125kHzOFDM card 125kHz steps: unsupported, supportedro Enumeration .1.3.6.1.4.1.562.3.1.200.4.3.4.1.13.9 |
inOfdmStatusFeatureStep166kHzOFDM card 166kHz steps: unsupported, supportedro Enumeration .1.3.6.1.4.1.562.3.1.200.4.3.4.1.13.10 |
inOfdmStatusFeatureInvSpectrumOFDM card inverted spectrum:unsupported, supportedro Enumeration .1.3.6.1.4.1.562.3.1.200.4.3.4.1.13.11 |
inOfdmStatusFeatureBasebandInpOFDM card baseband input: unsupported, supportedro Enumeration .1.3.6.1.4.1.562.3.1.200.4.3.4.1.13.12 |
inOfdmStatusFeatureRfInputOFDM card RF input: unsupported, supportedro Enumeration .1.3.6.1.4.1.562.3.1.200.4.3.4.1.13.13 |
inOfdmStatusFeatureIf70InputOFDM card 70MHz IF input: unsupported, supportedro Enumeration .1.3.6.1.4.1.562.3.1.200.4.3.4.1.13.14 |
inOfdmStatusFeatureIf140InputOFDM card 140MHz IF input: unsupported, supportedro Enumeration .1.3.6.1.4.1.562.3.1.200.4.3.4.1.13.15 |
inOfdmStatusFeatureFreqErrorOFDM card Frequency Error: unsupported, supportedro Enumeration .1.3.6.1.4.1.562.3.1.200.4.3.4.1.13.16 |
inOfdmStatusFeatureSysClkErrorOFDM card System Clock Error:unsupported, supportedro Enumeration .1.3.6.1.4.1.562.3.1.200.4.3.4.1.13.17 |
inOfdmStatusFeatureChanRippleOFDM card Channel Ripple: unsupported, supportedro Enumeration .1.3.6.1.4.1.562.3.1.200.4.3.4.1.13.18 |
inOfdmStatusFeatureHierarchyOFDM card Hierarchy: unsupported, supportedro Enumeration .1.3.6.1.4.1.562.3.1.200.4.3.4.1.13.19 |
inOfdmStatusFeatureFreqRangeOFDM card Frequency Range: unsupported, supportedro Enumeration .1.3.6.1.4.1.562.3.1.200.4.3.4.1.13.20 |
inputCardOfdmSetup OBJECT IDENTIFIER .1.3.6.1.4.1.562.3.1.200.4.3.4.2 |
inOfdmSetupTunerFreqOFDM card tuner frequency (kHz)rw INTEGER .1.3.6.1.4.1.562.3.1.200.4.3.4.2.1 |
inOfdmSetupAutoDetectOFDM card tuner auto-detect: disabled/enabledrw Enumeration .1.3.6.1.4.1.562.3.1.200.4.3.4.2.2 |
inOfdmSetupAutoDetectTimeoutOFDM card auto-detect timeout (ms)rw Uint32 .1.3.6.1.4.1.562.3.1.200.4.3.4.2.3 |
inOfdmSetupBandPlanNumberOFDM card band plan number:
0 = no band plan set (tune by frequency)
1 = Australia
2 = Europe VHF
3 = Europe CATV
4 = Italy
5 = Morocco
6 = New Zealand
7 = China
8 = OIRT
9 = Ireland
10 = South Africa
11 = French Overseas PTA
12 = France
13 = Japan
14 = USA
15 = CCIR
16 = UKrw Enumeration .1.3.6.1.4.1.562.3.1.200.4.3.4.2.4 |
inOfdmSetupBandPlanNameOFDM card band plan name (e.g. name of country)ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.562.3.1.200.4.3.4.2.5 |
inOfdmSetupChannelNumberOFDM card channel number within band plan
0 to number of channels in plan minus 1
Reports 65535 when the current band plan is 0 (NONE)
E.g:
65535 NONE
0 - 57 Australia
0 - 10 Europe VHF
0 - 16 Europe CATV
0 - 9 Italy
0 - 6 Morocco
0 - 9 New Zealand
0 - 61 China
0 - 11 OIRT
0 - 8 Ireland
0 - 9 South Africa
0 - 5 French Ov. PTA
0 - 9 France
0 - 62 Japan
0 - 81 USA
0 - 48 CCIR
0 - 48 UK
See inOfdmSetupChannelName for the channel namerw Uint32 .1.3.6.1.4.1.562.3.1.200.4.3.4.2.6 |
inOfdmSetupChannelNameOFDM card channel name within band plan as shown on the front panel
See inOfdmSetupChannelNumber for the channel numberro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.562.3.1.200.4.3.4.2.7 |
inOfdmSetupStepSizeOFDM card step size: 125kHz or 166kHzrw Enumeration .1.3.6.1.4.1.562.3.1.200.4.3.4.2.8 |
inOfdmSetupChannelSpacingOFDM card channel spacing: 6MHz, 7MHz, 8MHz or 12MHzrw Enumeration .1.3.6.1.4.1.562.3.1.200.4.3.4.2.9 |
inOfdmSetupGuardIntervalOFDM card guard interval: 1/32, 1/16, 1/8, 1/4rw Enumeration .1.3.6.1.4.1.562.3.1.200.4.3.4.2.10 |
inOfdmSetupCarrierModeOFDM card carrier mode: 2K, 8Krw Enumeration .1.3.6.1.4.1.562.3.1.200.4.3.4.2.11 |
inOfdmSetupInputTypeOFDM card input type: baseband, RF, 70MHz IF, 140MHz, IFrw Enumeration .1.3.6.1.4.1.562.3.1.200.4.3.4.2.12 |
inOfdmSetupSpectrumInvertOFDM card spectrum inversion: normal, invertedrw Enumeration .1.3.6.1.4.1.562.3.1.200.4.3.4.2.13 |
inOfdmSetupHierarchyStreamOFDM card hierarchy stream: none, low priority, high priorityrw Enumeration .1.3.6.1.4.1.562.3.1.200.4.3.4.2.14 |
inputCardMcd OBJECT IDENTIFIER .1.3.6.1.4.1.562.3.1.200.4.3.5 |
inputCardMcdStatus OBJECT IDENTIFIER .1.3.6.1.4.1.562.3.1.200.4.3.5.1 |
inputCardMcdSetup OBJECT IDENTIFIER .1.3.6.1.4.1.562.3.1.200.4.3.5.2 |
asiOutput OBJECT IDENTIFIER .1.3.6.1.4.1.562.3.1.200.5 |
asiOutputStatus OBJECT IDENTIFIER .1.3.6.1.4.1.562.3.1.200.5.1 |
asiOutputSetup OBJECT IDENTIFIER .1.3.6.1.4.1.562.3.1.200.5.2 |
asiOutputModeASI output mode: disabled, encrypted, partially-decrypted, decryptedrw Enumeration .1.3.6.1.4.1.562.3.1.200.5.2.1 |
asiOutputPacketLengthASI output packet length: 188 byte, 204 byte,rw Enumeration .1.3.6.1.4.1.562.3.1.200.5.2.2 |
director OBJECT IDENTIFIER .1.3.6.1.4.1.562.3.1.200.6 |
directorStatus OBJECT IDENTIFIER .1.3.6.1.4.1.562.3.1.200.6.1 |
directorDownloadStatusNDS Director download status (text)ro DisplayString .1.3.6.1.4.1.562.3.1.200.6.1.1 |
directorDownloadMessageNDS Director download message (text)ro DisplayString .1.3.6.1.4.1.562.3.1.200.6.1.2 |
directorCardStatusNDS Director card status: removed, inserted, failed, invalid, pairedro Enumeration .1.3.6.1.4.1.562.3.1.200.6.1.3 |
directorSetup OBJECT IDENTIFIER .1.3.6.1.4.1.562.3.1.200.6.2 |
directorCustomerIdNDS Director customer ID
THIS IS A FACTORY-ONLY PARAMETER AND DOES NOT APPEAR
ON PRODUCTION UNITSrw Uint8 .1.3.6.1.4.1.562.3.1.200.6.2.1 |
ncp OBJECT IDENTIFIER .1.3.6.1.4.1.562.3.1.200.7 |
ncpStatus OBJECT IDENTIFIER .1.3.6.1.4.1.562.3.1.200.7.1 |
ncpSetup OBJECT IDENTIFIER .1.3.6.1.4.1.562.3.1.200.7.2 |
alarmSources OBJECT IDENTIFIER .1.3.6.1.4.1.562.3.1.200.8 |
alarmLock OBJECT IDENTIFIER .1.3.6.1.4.1.562.3.1.200.8.1 |
alarmLockActionSpecifies which relay should be activated on a Lock alarmrw Enumeration .1.3.6.1.4.1.562.3.1.200.8.1.1 |
alarmLockSummarySpecifies whether the summary relay should be activated on a Lock alarmrw Enumeration .1.3.6.1.4.1.562.3.1.200.8.1.2 |
alarmLockStateThe current state of the Lock Alarmro Enumeration .1.3.6.1.4.1.562.3.1.200.8.1.3 |
alarmBer OBJECT IDENTIFIER .1.3.6.1.4.1.562.3.1.200.8.2 |
alarmBerActionSpecifies which relay should be activated on a BER alarmrw Enumeration .1.3.6.1.4.1.562.3.1.200.8.2.1 |
alarmBerSummarySpecifies whether the summary relay should be activated on a BER alarmrw Enumeration .1.3.6.1.4.1.562.3.1.200.8.2.2 |
alarmBerStateThe current state of the BER Alarmro Enumeration .1.3.6.1.4.1.562.3.1.200.8.2.3 |
alarmBerThresholdThe BER threshold at which to activated the BER alarmrw INTEGER .1.3.6.1.4.1.562.3.1.200.8.2.4 |
alarmMer OBJECT IDENTIFIER .1.3.6.1.4.1.562.3.1.200.8.3 |
alarmMerActionSpecifies which relay should be activated on a MER alarmrw Enumeration .1.3.6.1.4.1.562.3.1.200.8.3.1 |
alarmMerSummarySpecifies whether the summary relay should be activated on a MER alarmrw Enumeration .1.3.6.1.4.1.562.3.1.200.8.3.2 |
alarmMerStateThe current state of the MER Alarmro Enumeration .1.3.6.1.4.1.562.3.1.200.8.3.3 |
alarmMerThresholdThe MER threshold at which to activated the MER alarmrw INTEGER .1.3.6.1.4.1.562.3.1.200.8.3.4 |
alarmVideo OBJECT IDENTIFIER .1.3.6.1.4.1.562.3.1.200.8.4 |
alarmVideoActionSpecifies which relay should be activated on a Video alarmrw Enumeration .1.3.6.1.4.1.562.3.1.200.8.4.1 |
alarmVideoSummarySpecifies whether the summary relay should be activated on a Video
alarmrw Enumeration .1.3.6.1.4.1.562.3.1.200.8.4.2 |
alarmVideoStateThe current state of the Video Alarmro Enumeration .1.3.6.1.4.1.562.3.1.200.8.4.3 |
alarmAudio1 OBJECT IDENTIFIER .1.3.6.1.4.1.562.3.1.200.8.5 |
alarmAudio1ActionSpecifies which relay should be activated on a Audio1 alarmrw Enumeration .1.3.6.1.4.1.562.3.1.200.8.5.1 |
alarmAudio1SummarySpecifies whether the summary relay should be activated on a Audio1
alarmrw Enumeration .1.3.6.1.4.1.562.3.1.200.8.5.2 |
alarmAudio1StateThe current state of the Audio1 Alarmro Enumeration .1.3.6.1.4.1.562.3.1.200.8.5.3 |
alarmAudio2 OBJECT IDENTIFIER .1.3.6.1.4.1.562.3.1.200.8.6 |
alarmAudio2ActionSpecifies which relay should be activated on a Audio2 alarmrw Enumeration .1.3.6.1.4.1.562.3.1.200.8.6.1 |
alarmAudio2SummarySpecifies whether the summary relay should be activated on a Audio2
alarmrw Enumeration .1.3.6.1.4.1.562.3.1.200.8.6.2 |
alarmAudio2StateThe current state of the Audio2 Alarmro Enumeration .1.3.6.1.4.1.562.3.1.200.8.6.3 |
alarmAsync OBJECT IDENTIFIER .1.3.6.1.4.1.562.3.1.200.8.7 |
alarmAsyncActionSpecifies which relay should be activated on an Async Data alarmrw Enumeration .1.3.6.1.4.1.562.3.1.200.8.7.1 |
alarmAsyncSummarySpecifies whether the summary relay should be activated on an Async
Data alarmrw Enumeration .1.3.6.1.4.1.562.3.1.200.8.7.2 |
alarmAsyncStateThe current state of the Async Alarmro Enumeration .1.3.6.1.4.1.562.3.1.200.8.7.3 |
alarmCa OBJECT IDENTIFIER .1.3.6.1.4.1.562.3.1.200.8.8 |
alarmCaActionSpecifies which relay should be activated on a CA alarmrw Enumeration .1.3.6.1.4.1.562.3.1.200.8.8.1 |
alarmCaSummarySpecifies whether the summary relay should be activated on a CA alarmrw Enumeration .1.3.6.1.4.1.562.3.1.200.8.8.2 |
alarmCaStateThe current state of the CA Alarmro Enumeration .1.3.6.1.4.1.562.3.1.200.8.8.3 |
alarmVbi OBJECT IDENTIFIER .1.3.6.1.4.1.562.3.1.200.8.9 |
alarmVbiActionSpecifies which relay should be activated on a VBI alarmrw Enumeration .1.3.6.1.4.1.562.3.1.200.8.9.1 |
alarmVbiSummarySpecifies whether the summary relay should be activated on a VBI alarmrw Enumeration .1.3.6.1.4.1.562.3.1.200.8.9.2 |
alarmVbiStateThe current state of the VBI Alarmro Enumeration .1.3.6.1.4.1.562.3.1.200.8.9.3 |
alarmTemperature OBJECT IDENTIFIER .1.3.6.1.4.1.562.3.1.200.8.10 |
alarmTemperatureActionSpecifies which relay should be activated on a Temperature alarmrw Enumeration .1.3.6.1.4.1.562.3.1.200.8.10.1 |
alarmTemperatureSummarySpecifies whether the summary relay should be activated on a Temperature
alarmrw Enumeration .1.3.6.1.4.1.562.3.1.200.8.10.2 |
alarmTemperatureStateThe current state of the Temperature Alarmro Enumeration .1.3.6.1.4.1.562.3.1.200.8.10.3 |
alarmEbno OBJECT IDENTIFIER .1.3.6.1.4.1.562.3.1.200.8.11 |
alarmEbnoActionSpecifies which relay should be activated on an EbNo threshold alarmrw Enumeration .1.3.6.1.4.1.562.3.1.200.8.11.1 |
alarmEbnoSummarySpecifies whether the summary relay should be activated on a EbNo threshold
alarmrw Enumeration .1.3.6.1.4.1.562.3.1.200.8.11.2 |
alarmEbnoStateThe current state of the EbNo threshold Alarmro Enumeration .1.3.6.1.4.1.562.3.1.200.8.11.3 |
alarmEbnoThresholdThe EbNo threshold at which to activate the EbNo threshold alarmrw INTEGER .1.3.6.1.4.1.562.3.1.200.8.11.4 |
alarmPreBer OBJECT IDENTIFIER .1.3.6.1.4.1.562.3.1.200.8.12 |
alarmPreBerActionSpecifies which relay should be activated on an PreBER threshold alarmrw Enumeration .1.3.6.1.4.1.562.3.1.200.8.12.1 |
alarmPreBerSummarySpecifies whether the summary relay should be activated on a PreBER threshold
alarmrw Enumeration .1.3.6.1.4.1.562.3.1.200.8.12.2 |
alarmPreBerStateThe current state of the PreBER threshold Alarmro Enumeration .1.3.6.1.4.1.562.3.1.200.8.12.3 |
alarmPreBerThresholdThe PreBER threshold at which to activate the PreBER threshold alarmrw INTEGER .1.3.6.1.4.1.562.3.1.200.8.12.4 |
custom OBJECT IDENTIFIER .1.3.6.1.4.1.562.3.1.200.9 |
presets OBJECT IDENTIFIER .1.3.6.1.4.1.562.3.1.200.10 |