ENTERASYS-IEEE802DOT11EXT-MIB
AI MIB Summary
The ENTERASYS-IEEE802DOT11EXT-MIB provides read-write configuration management for proprietary IEEE 802.11 wireless parameters on Enterasys Networks access points and controllers that are absent from standard IEEE 802.11 MIBs. This module enables the administration of vendor-specific radio settings, security policies, and operational states required for fine-grained control of Enterasys wireless infrastructure.
This mib module defines a portion of the SNMP enterprise MIBs under Enterasys Networks enterprise OID as an extension to the IEEE802Dot11 MIB.
This Enterasys Networks Proprietary MIB was designed to be used for read-write access to configuration objects not provided by IEEE802.11 MIB, or any other standard MIB.
Main OID:
etsysDot11ExtMIB.1.3.6.1.4.1.5624.1.2.9
47
Objects
Active
Status
8
Dependencies
Imported Objects
Objects
47 total| Object Name |
|---|
etsysDot11ExtMIBThis mib module defines a portion of the SNMP enterprise
MIBs under Enterasys Networks enterprise OID as an extension
to the IEEE802Dot11 MIB.
This Enterasys Networks Proprietary MIB was designed to be
used for read-write access to configuration objects not provided
by IEEE802.11 MIB, or any other standard MIB. MODULE-IDENTITY .1.3.6.1.4.1.5624.1.2.9 |
etsysDot11ExtObjects OBJECT IDENTIFIER .1.3.6.1.4.1.5624.1.2.9.1 |
etsysDot11ExtLinkTest OBJECT IDENTIFIER .1.3.6.1.4.1.5624.1.2.9.1.1 |
etsysDot11ExtLinkTestTableThis table contains objects to test the link between a
requester (entity which sends out the management request
message) and a responder (entity which responds with
the appropriate management response message). An entity
could be either an Access Point(AP) or a station (STA). SEQUENCE OF EtsysDot11ExtLinkTestEntry .1.3.6.1.4.1.5624.1.2.9.1.1.1 |
etsysDot11ExtLinkTestEntryAn Entry (conceptual row) in the LinkTest Table.
By means of message transmission between requester
and responder, the communication quality between the
two stations can be determined. The requester and
responder can be any combination of AP and STA except
STA to STA in an Infrastructure Network (network which
has at least one AP present. EtsysDot11ExtLinkTestEntry .1.3.6.1.4.1.5624.1.2.9.1.1.1.1 |
etsysDot11ExtLTRemoteStationMACThe MAC address for the remote station to participate
in the Link Test.
To initiate a search for a participating station, write the
broadcast address (FF-FF-FF-FF-FF-FF) to this variable.rw MacAddress (SNMPv2-TC) .1.3.6.1.4.1.5624.1.2.9.1.1.1.1.1 |
etsysDot11ExtLTRemoteStationNameThe wireless station name of the remote station
participating in the Link Test.ro SnmpAdminString .1.3.6.1.4.1.5624.1.2.9.1.1.1.1.2 |
etsysDot11ExtLTTriggerWriting a 1 to this variable causes a single Link Test
request message to be sent to the remote station.rw INTEGER .1.3.6.1.4.1.5624.1.2.9.1.1.1.1.3 |
etsysDot11ExtLTRemoteContentsThe exact byte-by-byte contents of the Link Test packet returned by
the remote station.ro OCTET STRING .1.3.6.1.4.1.5624.1.2.9.1.1.1.1.4 |
etsysDot11ExtGeneral OBJECT IDENTIFIER .1.3.6.1.4.1.5624.1.2.9.1.2 |
etsysDot11ExtGeneralTableThis table contains all the objects that must be
configured on every radio card installed in the
Access Point regardless of the operating mode in use. SEQUENCE OF EtsysDot11ExtGeneralEntry .1.3.6.1.4.1.5624.1.2.9.1.2.1 |
etsysDot11ExtGeneralEntryAn Entry (conceptual row) in the Dot11General Table.
This allows for multiple instances of radio cards
in the Access Point. EtsysDot11ExtGeneralEntry .1.3.6.1.4.1.5624.1.2.9.1.2.1.1 |
etsysDot11ExtPCCardTypeThe type of PC card inserted in the Access Point.ro Enumeration .1.3.6.1.4.1.5624.1.2.9.1.2.1.1.1 |
etsysDot11ExtPCCardVersionsSpecifies the version identifiers for the PC card.
This will indicate both the Hardware and the Firmware
versions.ro SnmpAdminString .1.3.6.1.4.1.5624.1.2.9.1.2.1.1.2 |
etsysDot11ExtBridgeModeCURRENT Access Point bridge mode state.
In workgroup mode all communications between clients
passes through the Access Point.
LAN-to-LAN mode is the improved name for 802.11.
LAN-to-LAN used to be called full-bridge pre-802.11.
This mode is a method of connecting two wired LAN's
via a wireless link, also referred to as Point-to-Point
mode.
LAN-to-LAN-HUB mode allows the interconnection of multiple
(ie. more than two) wired LAN's via wireless links, also
referred to as Point-to-MultiPoint mode.
When operating in multimode the Access Point can simultaneously
operate in both workgroup mode and either Point-to-Point or
Point-to-MultiPoint modes.
This object must be saved across a system reset and/or a
power cycle.rw Enumeration .1.3.6.1.4.1.5624.1.2.9.1.2.1.1.3 |
etsysDot11ExtResetOptionsnoReset (0)
No reset is performed. A 'get' on this object always returns
this value.
resetRadioCardIfNecessary (1)
Some parameters can only be given to the card at initialization
time, and if any of these are changed, a card reset will be
necessary for them to go into place. The card will be reset at
this time if any of those parameters have indeed been changed.
resetRadioCardRegardless (2)
Forces the radio card to reset, even if no radio card
parameters have been changed.rw Enumeration .1.3.6.1.4.1.5624.1.2.9.1.2.1.1.4 |
etsysDot11ExtSystemScaleSpecifies the CURRENT Access Point density in the
Extended Service Set (ESS).
This object must be saved across a system reset and/or a
power cycle.rw Enumeration .1.3.6.1.4.1.5624.1.2.9.1.2.1.1.5 |
etsysDot11ExtSecureAccessWhen this mode is set to enabled, the AP will only associate
with stations that have the same network name as the AP.
When this mode is set to disabled, a station with the
network name of ANY is allowed to associate.
This object must be saved across a system reset and/or a
power cycle.rw EnabledStatus (P-BRIDGE-MIB) .1.3.6.1.4.1.5624.1.2.9.1.2.1.1.6 |
etsysDot11ExtMulticastTxRateThis value specifies the Multicast data transmission
rate of the AP. It is implemented when cards that operate
faster than the 2Mbit 802.11 standard are inserted.
This object must be saved across a system reset and/or a
power cycle.rw Enumeration .1.3.6.1.4.1.5624.1.2.9.1.2.1.1.7 |
etsysDot11ExtIntraBSSRelayWhen this mode is enabled the AP entity within the PC Card will
relay frames to destined for stations associated with it and will NOT
forward them to the bridging entity within the AP.
When this mode is set to disabled, the AP entity within the PC Card
will not relay frames from wireless client(s) to station(s) associated with it,
instead forwards frames to the bridging entity within the AP.
This object must be saved across a system reset and/or a
power cycle.rw EnabledStatus (P-BRIDGE-MIB) .1.3.6.1.4.1.5624.1.2.9.1.2.1.1.8 |
etsysDot11ExtStationNameDURABLE:
The wireless station name sent out as part of
the beacon messages. Valid only when a DS card
is inserted in the Access Point.rw SnmpAdminString .1.3.6.1.4.1.5624.1.2.9.1.2.1.1.9 |
etsysDot11ExtBldg OBJECT IDENTIFIER .1.3.6.1.4.1.5624.1.2.9.1.3 |
etsysDot11ExtBldgTableThis table contains the objects required to enable
the Access Point to operate in Point-to-MultiPoint mode. SEQUENCE OF EtsysDot11ExtBldgEntry .1.3.6.1.4.1.5624.1.2.9.1.3.1 |
etsysDot11ExtBldgEntryAn Entry (conceptual row) in the Dot11Bldg Table.
A collection of objects containing information for activating
and using the Access Point in Point-to-MultiPoint mode. EtsysDot11ExtBldgEntry .1.3.6.1.4.1.5624.1.2.9.1.3.1.1 |
etsysDot11ExtBldgRemoteMAC1The MAC address for the remote station participating
in a 802.11 Building-to-Building link.
This object must be saved across a system reset and/or a
power cycle.rw MacAddress (SNMPv2-TC) .1.3.6.1.4.1.5624.1.2.9.1.3.1.1.1 |
etsysDot11ExtBldgRemoteMAC2The MAC address for the remote station participating
in a 802.11 Building-to-Building link.
This object must be saved across a system reset and/or a
power cycle.rw MacAddress (SNMPv2-TC) .1.3.6.1.4.1.5624.1.2.9.1.3.1.1.2 |
etsysDot11ExtBldgRemoteMAC3The MAC address for the remote station participating
in a 802.11 Building-to-Building link.
This object must be saved across a system reset and/or a
power cycle.rw MacAddress (SNMPv2-TC) .1.3.6.1.4.1.5624.1.2.9.1.3.1.1.3 |
etsysDot11ExtBldgRemoteMAC4The MAC address for the remote station participating
in a 802.11 Building-to-Building link.
This object must be saved across a system reset and/or a
power cycle.rw MacAddress (SNMPv2-TC) .1.3.6.1.4.1.5624.1.2.9.1.3.1.1.4 |
etsysDot11ExtBldgRemoteMAC5The MAC address for the remote station participating
in a 802.11 Building-to-Building link.
This object must be saved across a system reset and/or a
power cycle.rw MacAddress (SNMPv2-TC) .1.3.6.1.4.1.5624.1.2.9.1.3.1.1.5 |
etsysDot11ExtBldgRemoteMAC6The MAC address for the remote station participating
in a 802.11 Building-to-Building link.
This object must be saved across a system reset and/or a
power cycle.rw MacAddress (SNMPv2-TC) .1.3.6.1.4.1.5624.1.2.9.1.3.1.1.6 |
etsysDot11ExtBldgMPActivationKeyPoint-to-multipoint bridge mode requires an activation
key to enable. A valid multipoint activation key must
be entered as a string of ACSCII characters translating
to the binary HEX value of the key before the Access Point
will accept the point-to-multipoint bridge mode setting.
Returns SNMP_BAD_VALUE if validation fails.
This object must be saved across a system reset and/or a
power cycle.rw OCTET STRING .1.3.6.1.4.1.5624.1.2.9.1.3.1.1.7 |
etsysDot11ExtWEP OBJECT IDENTIFIER .1.3.6.1.4.1.5624.1.2.9.1.4 |
etsysDot11ExtWEPDefaultKeysTableConceptual table for WEP default keys. This table shall
contain the four WEP default secret key values
corresponding to the four possible KeyID values. The WEP
default secret keys are logically WRITE-ONLY. Attempts to
read the entries in this table shall return unsuccessful
status and a value of null. The default value of each WEP
default key shall be null. SEQUENCE OF EtsysDot11ExtWEPDefaultKeysEntry .1.3.6.1.4.1.5624.1.2.9.1.4.1 |
etsysDot11ExtWEPDefaultKeysEntryAn Entry (conceptual row) in the WEP Default Keys Table.
A collection of objects containing information used to
determine if a WEPkey as been defined and if so, the
value of the WEPkey. EtsysDot11ExtWEPDefaultKeysEntry .1.3.6.1.4.1.5624.1.2.9.1.4.1.1 |
etsysDot11ExtWEPKeyDefinedThe state column used for determining if an
encryption key is set (true) or not (false),
false is the default value.ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.5624.1.2.9.1.4.1.1.1 |
etsysDot11ExtWEPKeyValueA WEP default secret key value. For 40-bit encryption
use 5 printable characters or 10 HEX digits. For 128-bit
encryption use 13 printable characters or 26 HEX digits.
This object must be saved across a system reset and/or a
power cycle.rw OCTET STRING .1.3.6.1.4.1.5624.1.2.9.1.4.1.1.2 |
etsysDot11ExtWEPEnhancedTableConceptual table for WEP default keys. This table shall
contain the four WEP default secret key values
corresponding to the four possible KeyID values. The WEP
default secret keys are logically WRITE-ONLY. Attempts to
read the entries in this table shall return unsuccessful
status and a value of null. The default value of each WEP
default key shall be null. SEQUENCE OF EtsysDot11ExtWEPEnhancedEntry .1.3.6.1.4.1.5624.1.2.9.1.4.2 |
etsysDot11ExtWEPEnhancedEntryAn Entry (conceptual row) in the WEP Default Keys Table.
A collection of objects containing information used to
determine if a WEPkey as been defined and if so, the
value of the WEPkey. EtsysDot11ExtWEPEnhancedEntry .1.3.6.1.4.1.5624.1.2.9.1.4.2.1 |
etsysDot11ExtWEPEnhancedImplementedThis value indicates whether the AP is capable of Enhanced
Wireless Equivalent Privacy (WEP), using 128-bit keys.ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.5624.1.2.9.1.4.2.1.1 |
etsysDot11ExtEffect OBJECT IDENTIFIER .1.3.6.1.4.1.5624.1.2.9.1.5 |
etsysDot11ExtOIDNotInEffectTableThis table will be used to determine which wireless
parameters have been modified but are not yet in effect.
These parameters will not take effect until a reset has been
performed. SEQUENCE OF EtsysDot11ExtOIDNotInEffectEntry .1.3.6.1.4.1.5624.1.2.9.1.5.1 |
etsysDot11ExtOIDNotInEffectEntry EtsysDot11ExtOIDNotInEffectEntry .1.3.6.1.4.1.5624.1.2.9.1.5.1.1 |
etsysDot11ExtOIDIndexThis object will keep a list of OIDS AutonomousType (SNMPv2-TC) .1.3.6.1.4.1.5624.1.2.9.1.5.1.1.1 |
etsysDot11ExtOIDNotInEffectThis object specifies if the OID being accesed currently
has been changed but is not in effect.ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.5624.1.2.9.1.5.1.1.2 |
etsysDot11ExtConformance OBJECT IDENTIFIER .1.3.6.1.4.1.5624.1.2.9.2 |
etsysDot11ExtGroups OBJECT IDENTIFIER .1.3.6.1.4.1.5624.1.2.9.2.1 |
etsysDot11ExtCompliances OBJECT IDENTIFIER .1.3.6.1.4.1.5624.1.2.9.2.2 |