ECLAPBEXT-MIB
AI MIB Summary
Standard SNMP MIB module defining data structures for ECLAPBEXT-MIB.
78
Objects
Active
Status
3
Dependencies
Imported Objects
Objects
78 total| Object Name |
|---|
eicon OBJECT IDENTIFIER .1.3.6.1.4.1.434 |
RFC1155-SMI Unknown .1.3.6.1.4.1.434 |
lapbTrapBandwidthShortageThis trap indicates that the amount of bandwidth used on the
specified port has risen above lapbBandwidthHigh percent over
lapbBandwidthNumPeriods of lapbBandwidthSecs. The next two
parameters indicate the percentage of the total bandwidth used in
each direction (Transmitting or Receiving) over the last
lapbBandwidthSecs number of seconds. The final parameter indicates
the direction(s) in which the bandwidth threshold has been
exceeded TRAP-TYPE .1.3.6.1.4.1.434.0.411 |
lapbTrapBandwidthClearThis trap indicates that the condition causing a previous
lapbTrapBandwidthShortage no longer applies; in particular that
the bandwidth being used on the specified port has dropped to below
lapbBandwidthLow percent over the last lapbBandwidthSecs number of
seconds The final parameter indicates the direction(s) in which the
bandwidth exceeded condition has been cleared TRAP-TYPE .1.3.6.1.4.1.434.0.412 |
management OBJECT IDENTIFIER .1.3.6.1.4.1.434.2 |
mibv2 OBJECT IDENTIFIER .1.3.6.1.4.1.434.2.2 |
module OBJECT IDENTIFIER .1.3.6.1.4.1.434.2.2.4 |
lapbext OBJECT IDENTIFIER .1.3.6.1.4.1.434.2.2.4.1 |
lapbCountersTableRuntime counters table, one row per port SEQUENCE OF LapbCountEntry .1.3.6.1.4.1.434.2.2.4.1.1 |
lapbCountEntryThe set of counters for one port. Can be reset to 0. LapbCountEntry .1.3.6.1.4.1.434.2.2.4.1.1.1 |
lapbCountPortRefThe port number, the same as lapbParmPortRef from the
lapbParmTable.ro INTEGER .1.3.6.1.4.1.434.2.2.4.1.1.1.1 |
lapbCountRetransmisThe number of times a frame has been retransmittedro Counter .1.3.6.1.4.1.434.2.2.4.1.1.1.2 |
lapbCountSABMTxsThe number of Set Asynchronous Balanced Mode frames sentro Counter .1.3.6.1.4.1.434.2.2.4.1.1.1.3 |
lapbCountSABMRxsThe number of Set Asynchronous Balanced Mode frames receivedro Counter .1.3.6.1.4.1.434.2.2.4.1.1.1.4 |
lapbCountDISCTxsThe number of Disconnect frames sentro Counter .1.3.6.1.4.1.434.2.2.4.1.1.1.5 |
lapbCountDISCRxsThe number of Disconnect frames receivedro Counter .1.3.6.1.4.1.434.2.2.4.1.1.1.6 |
lapbCountDMsTxsThe number of Disconnected Mode frames sentro Counter .1.3.6.1.4.1.434.2.2.4.1.1.1.7 |
lapbCountDMsRxsThe number of Disconnected Mode frames receivedro Counter .1.3.6.1.4.1.434.2.2.4.1.1.1.8 |
lapbCountRNRsTxsThe number of Receiver Not Ready frames sentro Counter .1.3.6.1.4.1.434.2.2.4.1.1.1.9 |
lapbCountRNRsRxsThe number of Receiver Not Ready frames receivedro Counter .1.3.6.1.4.1.434.2.2.4.1.1.1.10 |
lapbCountUATxsThe number of Unnumbered Acknowledgement frames transmitted.ro Counter .1.3.6.1.4.1.434.2.2.4.1.1.1.11 |
lapbCountUARxsThe number of Unnumbered Acknowledgement frames received.ro Counter .1.3.6.1.4.1.434.2.2.4.1.1.1.12 |
lapbCountRRTxsThe number of Receiver Ready frames transmitted.ro Counter .1.3.6.1.4.1.434.2.2.4.1.1.1.13 |
lapbCountRRRxsThe number of Receiver Ready frames received.ro Counter .1.3.6.1.4.1.434.2.2.4.1.1.1.14 |
lapbCountFRMRTxsThe number of Frame Reject frames sent.ro Counter .1.3.6.1.4.1.434.2.2.4.1.1.1.15 |
lapbCountFRMRRxsThe number of Frame Reject frames received.ro Counter .1.3.6.1.4.1.434.2.2.4.1.1.1.16 |
lapbCountBadCRCTxsThe number of frames sent with bad CRC.ro Counter .1.3.6.1.4.1.434.2.2.4.1.1.1.17 |
lapbCountBadCRCRxsThe number of frames received with bad CRC.ro Counter .1.3.6.1.4.1.434.2.2.4.1.1.1.18 |
lapbCountAbortTxsThe number of frames sent with Abort indication.ro Counter .1.3.6.1.4.1.434.2.2.4.1.1.1.19 |
lapbCountAbortRxsThe number of frames received with Abort indication.ro Counter .1.3.6.1.4.1.434.2.2.4.1.1.1.20 |
lapbCountBadTypeTxsThe number of Unknown frames sent.ro Counter .1.3.6.1.4.1.434.2.2.4.1.1.1.21 |
lapbCountBadTypeRxsThe number of Unknown frames received.ro Counter .1.3.6.1.4.1.434.2.2.4.1.1.1.22 |
lapbCountInfoFrameTxsThe number of Information frames sent.ro Counter .1.3.6.1.4.1.434.2.2.4.1.1.1.23 |
lapbCountInfoFrameRxsThe number of Information frames received.ro Counter .1.3.6.1.4.1.434.2.2.4.1.1.1.24 |
lapbCountUnderrunThe number of times that more frames have been
transmitted than the receiver can handle.ro Counter .1.3.6.1.4.1.434.2.2.4.1.1.1.25 |
lapbCountOverrunThe number of times that the EiconCard could not
handle incoming frames.ro Counter .1.3.6.1.4.1.434.2.2.4.1.1.1.26 |
lapbCountXIDTxsThe number of Exchange Station Identification
frames sent.ro Counter .1.3.6.1.4.1.434.2.2.4.1.1.1.27 |
lapbCountXIDRxsThe number of Exchange Station Identification
frames received.ro Counter .1.3.6.1.4.1.434.2.2.4.1.1.1.28 |
lapbBandwidthTableThe table of configurable and informational parameters with
respect to the bandwidth traps for lapb interfaces SEQUENCE OF LapbBandwidthEntry .1.3.6.1.4.1.434.2.2.4.1.2 |
lapbBandwidthEntryThe set of configurable and informational parameters to support
the bandwidth traps for each lapb interface LapbBandwidthEntry .1.3.6.1.4.1.434.2.2.4.1.2.1 |
lapbBandwidthIndexThe identifier of the EiconPort assigned by the agent.ro INTEGER .1.3.6.1.4.1.434.2.2.4.1.2.1.1 |
lapbBandwidthHighThe higher configurable threshold for the
lapbTrapBandwidthShortage. If the percentage of bandwidth being
used exceeds this amount over a configurable number of seconds
(lapbBandwidthSecs) for a configurable number of consecutive
periods, (lapbBandwidthNumPeriods), then the trap is sent and the
lapbBandwidthTrapsStatus is changed accordinglyrw INTEGER .1.3.6.1.4.1.434.2.2.4.1.2.1.2 |
lapbBandwidthLowThe lower configurable threshold for the lapbTrapBandwidthClear.
If the percentage of bandwidth being used drops below this amount,
subsequent to a lapbTrapBandwidthShortage, then the trap is sent
and the lapbBadwidthTrapsStatus is changed accordingly. Note that
this value MUST be below that for labpBandwidthHighrw INTEGER .1.3.6.1.4.1.434.2.2.4.1.2.1.3 |
lapbBandwidthSecsThe number of seconds over which the bandwidth is calculated.rw INTEGER .1.3.6.1.4.1.434.2.2.4.1.2.1.4 |
lapbBandwidthNumPeriodsThe number of consecutive periods, each of length
lapbBandwidthSecs seconds, that the condition must be present for
before the lapbBandwidthShortage trap is sent.rw INTEGER (1 .. 100) .1.3.6.1.4.1.434.2.2.4.1.2.1.5 |
lapbBandwidthTrapStateThis variable indicates whether the agent should
generate the lapbTrapBandwidthShortage and lapbTrapBandwidthClear
traps if the relevant conditions arise. Set this value to disabled
to stop these traps being generatedrw Enumeration .1.3.6.1.4.1.434.2.2.4.1.2.1.6 |
lapbBandwidthTrapStatusThe status of the bandwidth traps. This value should be polled to
determine whether or not the bandwidth shortage condition is
present and a trap has been sent.ro BandwidthStatus .1.3.6.1.4.1.434.2.2.4.1.2.1.7 |
lapbBandwidthRxInUseThe percentage of bandwidth that is currently in use receiving
incoming traffic.ro INTEGER .1.3.6.1.4.1.434.2.2.4.1.2.1.8 |
lapbBandwidthTxInUseThe percentage of bandwidth that is currently in use transmitting
outgoing traffic.ro INTEGER .1.3.6.1.4.1.434.2.2.4.1.2.1.9 |
lapbOperTableThis table contains configuration
information about interface parameters
currently set in the interface. Many of
these objects have corresponding objects in
the lapbAdmnTable. SEQUENCE OF LapbOperEntry .1.3.6.1.4.1.434.2.2.4.1.3 |
lapbOperEntryCurrently set parameter values for a
specific LAPB. LapbOperEntry .1.3.6.1.4.1.434.2.2.4.1.3.1 |
lapbOperIndexThe ifIndex value for the LAPB interface.ro IfIndexType .1.3.6.1.4.1.434.2.2.4.1.3.1.1 |
lapbOperStationTypeIdentifies the current operating station
type of this interface. A value of dxe (3)
indicates XID negotiation has not yet taken
place.ro Enumeration .1.3.6.1.4.1.434.2.2.4.1.3.1.2 |
lapbOperControlFieldThe current operating size of the sequence
numbers used to number frames.ro Enumeration .1.3.6.1.4.1.434.2.2.4.1.3.1.3 |
lapbOperTransmitN1FrameSizeThe current operating N1 frame size used
for the maximum number of bits in a frame
this DTE can transmit. This excludes flags
and 0 bits inserted for transparency.ro PositiveInteger .1.3.6.1.4.1.434.2.2.4.1.3.1.4 |
lapbOperReceiveN1FrameSizeThe current operating N1 frame size used
for the maximum number of bits in a frame
the DCE/remote DTE can transmit. This
excludes flags and 0 bits inserted for
transparency.ro PositiveInteger .1.3.6.1.4.1.434.2.2.4.1.3.1.5 |
lapbOperTransmitKWindowSizeThe current PDU window size this Interface
uses to transmit. This is the maximum
number of unacknowledged sequenced PDUs that
may be outstanding from this DTE at any one
time.ro INTEGER .1.3.6.1.4.1.434.2.2.4.1.3.1.6 |
lapbOperReceiveKWindowSizeThe current receive PDU window size for
this Interface. This is the maximum number
of unacknowledged sequenced PDUs that may be
outstanding from the DCE/remote DTE at any
one time.ro INTEGER .1.3.6.1.4.1.434.2.2.4.1.3.1.7 |
lapbOperN2RxmitCountThe current N2 retry counter used for this
interface. This specifies the number of
times a PDU will be resent after the T1
timer expires without an acknowledgement for
the PDU.ro INTEGER .1.3.6.1.4.1.434.2.2.4.1.3.1.8 |
lapbOperT1AckTimerThe current T1 timer for this interface.
This specifies the maximum time in
Milliseconds to wait for acknowledgment of a
PDU.ro PositiveInteger .1.3.6.1.4.1.434.2.2.4.1.3.1.9 |
lapbOperT2AckDelayTimerThe current T2 timer for this interface.
This specifies the maximum time in
Milliseconds to wait before sending an
acknowledgment for a sequenced PDU. A value
of zero means there will be no delay in
acknowledgement generation.ro PositiveInteger .1.3.6.1.4.1.434.2.2.4.1.3.1.10 |
lapbOperT3DisconnectTimerThe current T3 timer for this interface.
This specifies the time in Milliseconds to
wait before considering the link
disconnected. A value of zero indicates the
link will be considered disconnected upon
completion of the frame exchange to
disconnect the link.ro PositiveInteger .1.3.6.1.4.1.434.2.2.4.1.3.1.11 |
lapbOperT4IdleTimerThe current T4 timer for this interface.
This specifies the maximum time in
Milliseconds to allow without frames being
exchanged on the data link. A value of
2147483647 indicates no idle timer is being
kept.rw PositiveInteger .1.3.6.1.4.1.434.2.2.4.1.3.1.12 |
lapbOperPortIdThis object identifies an instance of the
index object in the first group of objects
in the MIB specific to the physical device
or interface used to send and receive
frames. If an agent does not support any
such objects, it should return nullSpec
OBJECT IDENTIFIER {0 0}.ro OBJECT IDENTIFIER .1.3.6.1.4.1.434.2.2.4.1.3.1.13 |
lapbOperProtocolVersionIdThis object identifies the version of the
lapb protocol implemented by this
interface.ro OBJECT IDENTIFIER .1.3.6.1.4.1.434.2.2.4.1.3.1.14 |
lapbFlowTableThis table defines the objects recorded by
LAPB to provide information about the
traffic flow through the interface. SEQUENCE OF LapbFlowEntry .1.3.6.1.4.1.434.2.2.4.1.4 |
lapbFlowEntryThe information regarding the effects of
flow controls in LAPB. LapbFlowEntry .1.3.6.1.4.1.434.2.2.4.1.4.1 |
lapbFlowIfIndexThe ifIndex value for the LAPB Interface.ro IfIndexType .1.3.6.1.4.1.434.2.2.4.1.4.1.1 |
lapbFlowStateChangesThe number of LAPB State Changes, including
resets.ro Counter .1.3.6.1.4.1.434.2.2.4.1.4.1.2 |
lapbFlowChangeReasonThe reason for the most recent incrementing
of lapbFlowStateChanges. A DM or DISC frame
generated to initiate link set-up does not
alter this object. When the MIB-II object
ifOperStatus does not have a value of
testing, there exists a correlation between
this object and ifOperStatus. IfOperStatus
will have a value of up when this object
contains: abmEntered, abmeEntered,
abmReset, or abmeReset. IfOperStatus will
have a value of down when this object has a
value of notStarted, or dmReceived through
n2Timeout. There is no correlation when
this object has the value other.ro Enumeration .1.3.6.1.4.1.434.2.2.4.1.4.1.3 |
lapbFlowCurrentModeThe current condition of the conversation.ro Enumeration .1.3.6.1.4.1.434.2.2.4.1.4.1.4 |
lapbFlowBusyDefersThe number of times this device was unable
to transmit a frame due to a perceived
remote busy condition. Busy conditions can
result from the receipt of an RNR from the
remote device, the lack of valid sequence
number space (window saturation), or other
conditions.ro Counter .1.3.6.1.4.1.434.2.2.4.1.4.1.5 |
lapbFlowRejOutPktsThe number of REJ or SREJ frames sent by
this station.ro Counter .1.3.6.1.4.1.434.2.2.4.1.4.1.6 |
lapbFlowRejInPktsThe number of REJ or SREJ frames received
by this station.ro Counter .1.3.6.1.4.1.434.2.2.4.1.4.1.7 |
lapbFlowT1TimeoutsThe number of times a re-transmission was
effected by the T1 Timer expiring.ro Counter .1.3.6.1.4.1.434.2.2.4.1.4.1.8 |
lapbFlowFrmrSentThe Information Field of the FRMR most
recently sent. If no FRMR has been sent
(the normal case) or the information isn't
available, this will be an OCTET STRING of
zero length.ro OCTET STRING .1.3.6.1.4.1.434.2.2.4.1.4.1.9 |
lapbFlowFrmrReceivedThe Information Field of the FRMR most
recently received. If no FRMR has been
received (the normal case) or the
information isn't available, this will be an
OCTET STRING of zero length.ro OCTET STRING .1.3.6.1.4.1.434.2.2.4.1.4.1.10 |
lapbFlowXidReceivedThe Information Field of the XID frame most
recently received. If no XID frame has been
received, this will be an OCTET STRING of
zero length.ro OCTET STRING .1.3.6.1.4.1.434.2.2.4.1.4.1.11 |