Home/Catalog/EICON-DIALER-MIB

EICON-DIALER-MIB

AI MIB Summary

Standard SNMP MIB module defining data structures for EICON-DIALER-MIB.

445
Objects
Active
Status
3
Dependencies

Imported Objects

RFC1155-SMI
RFC-1212
RFC1213-MIB

Objects

445 total
Object Name
eicon
OBJECT IDENTIFIER
.1.3.6.1.4.1.434
RFC1155-SMI
Unknown
.1.3.6.1.4.1.434
management
OBJECT IDENTIFIER
.1.3.6.1.4.1.434.2
mibv2
OBJECT IDENTIFIER
.1.3.6.1.4.1.434.2.2
module
OBJECT IDENTIFIER
.1.3.6.1.4.1.434.2.2.4
dialer
OBJECT IDENTIFIER
.1.3.6.1.4.1.434.2.2.4.16
dialerInfoTableGeneral Information Table for dailer.
SEQUENCE OF DialerInfoEntry
.1.3.6.1.4.1.434.2.2.4.16.1
dialerInfoEntryThe set of dialer configuration attributes for one port.
DialerInfoEntry
.1.3.6.1.4.1.434.2.2.4.16.1.1
dialerInfoPortRefThe id of the port, equal to portIndex from the port group. It identifies the port to which the configuration parameters apply.ro
PortRef
.1.3.6.1.4.1.434.2.2.4.16.1.1.1
dialerInfoTypeType of interface connecting the gateway to local or remote host computers.ro
Enumeration
.1.3.6.1.4.1.434.2.2.4.16.1.1.2
dialerInfoTimeStartThe time elapsed since the dialer was statrted.ro
TimeTicks (SNMPv2-SMI)
.1.3.6.1.4.1.434.2.2.4.16.1.1.3
dialerInfoTimeConnectThe time elapsed since the dialer established the current connection.ro
TimeTicks (SNMPv2-SMI)
.1.3.6.1.4.1.434.2.2.4.16.1.1.4
dialerInfoLineSpeedThe speed setting of the driver (line speed), or the dialer (modem speed).ro
INTEGER
.1.3.6.1.4.1.434.2.2.4.16.1.1.5
dialerInfoDataEncodingThe type of data encoding used on the connection.ro
DataEncoding
.1.3.6.1.4.1.434.2.2.4.16.1.1.6
dialerInfoClockTypeThe type of clocking used by the modem.ro
ClockType
.1.3.6.1.4.1.434.2.2.4.16.1.1.7
dialerDirectInfoTableGeneral Information Table for Direct dialer.
SEQUENCE OF DialerDirectInfoEntry
.1.3.6.1.4.1.434.2.2.4.16.2
dialerDirectInfoEntryThe set of dialer configuration attributes for one port.
DialerDirectInfoEntry
.1.3.6.1.4.1.434.2.2.4.16.2.1
dialerDirectPortRefThe id of the port, equal to portIndex from the port group. It identifies the port to which the configuration parameters apply.ro
PortRef
.1.3.6.1.4.1.434.2.2.4.16.2.1.1
dialerDirectIfTypeInterface type of the Dialerro
Enumeration
.1.3.6.1.4.1.434.2.2.4.16.2.1.2
dialerDirectModeStates whether the modem is connected to a Leased or Dial-Up phone line.ro
Enumeration
.1.3.6.1.4.1.434.2.2.4.16.2.1.3
dialerDirectConnDelayMax time for connection in seconds.ro
INTEGER
.1.3.6.1.4.1.434.2.2.4.16.2.1.4
dialerDirectRtsDelayDelay between arrival of DSR and activation of RTS circuit in msec.ro
INTEGER
.1.3.6.1.4.1.434.2.2.4.16.2.1.5
dialerDirectStateState of the Direct dialer: closed(1) - Modem signals on a dial modem were lost. opening(2) - Link is being set up (modem dialing). asnwering(3) - Accepting call from remote. delaying(4) - Waiting for a timer to expire. opened(5) - Physical link is established. Closing(6) - Disconnecting the physical link. ringing (7) - answer-wait (8) - originating (9) - connecting (10) - connect-delay (11) - connected (12) - disconnecting (13) - remote-disc (14) - local-disc (15) - connect-req (16) - incomming-call (17) - outgoing-call (18) - outgoing-delay (19) -ro
Enumeration
.1.3.6.1.4.1.434.2.2.4.16.2.1.6
dialerDirectRs232InfoTableGeneral Information Table for Direct dialer RS232.
SEQUENCE OF DialerDirectRs232InfoEntry
.1.3.6.1.4.1.434.2.2.4.16.3
dialerDirectRs232InfoEntryThe set of dialer configuration attributes for one port.
DialerDirectRs232InfoEntry
.1.3.6.1.4.1.434.2.2.4.16.3.1
dialerDirectRs232PortRefThe id of the port, equal to portIndex from the port group. It identifies the port to which the configuration parameters apply.ro
PortRef
.1.3.6.1.4.1.434.2.2.4.16.3.1.1
dialerDirectRs232DbounceDelayThis applies to Leased line only. It is the amount of time, expressed in msecs, that DSR signal stays on.ro
INTEGER
.1.3.6.1.4.1.434.2.2.4.16.3.1.2
dialerDirectRs232DtrSignalThe current status of the DTR signal.ro
OnOff
.1.3.6.1.4.1.434.2.2.4.16.3.1.3
dialerDirectRs232DsrSignalThe current status of the DSR signal.rw
OnOff
.1.3.6.1.4.1.434.2.2.4.16.3.1.4
dialerDirectRs232RiSignalThe current status of the RI signal. This is set to ON when there is an incoming call.ro
OnOff
.1.3.6.1.4.1.434.2.2.4.16.3.1.5
dialerDirectX21InfoTableGeneral Information Table for Direct dialer X21.
SEQUENCE OF DialerDirectX21InfoEntry
.1.3.6.1.4.1.434.2.2.4.16.4
dialerDirectX21InfoEntryThe set of dialer configuration attributes for one port.
DialerDirectX21InfoEntry
.1.3.6.1.4.1.434.2.2.4.16.4.1
dialerDirectX21PortRefThe id of the port, equal to portIndex from the port group. It identifies the port to which the configuration parameters apply.ro
PortRef
.1.3.6.1.4.1.434.2.2.4.16.4.1.1
dialerDirectX21CtrlSignalThe control circuit status.ro
OnOff
.1.3.6.1.4.1.434.2.2.4.16.4.1.2
dialerDirectX21IndicSignalThe indication circuit status.ro
OnOff
.1.3.6.1.4.1.434.2.2.4.16.4.1.3
dialerV25bisInfoTableGeneral Information Table for V25Bis dialer.
SEQUENCE OF DialerV25bisInfoEntry
.1.3.6.1.4.1.434.2.2.4.16.5
dialerV25bisInfoEntryThe set of dialer configuration attributes for one port.
DialerV25bisInfoEntry
.1.3.6.1.4.1.434.2.2.4.16.5.1
dialerV25bisPortRefThe Port Number.ro
PortRef
.1.3.6.1.4.1.434.2.2.4.16.5.1.1
dialerV25bisPrimaryNumThe main telephone number stored in the dialer.rw
DisplayString
.1.3.6.1.4.1.434.2.2.4.16.5.1.2
dialerV25bisSecondaryNumThe alternate telephone number stored in the dialer. This number is dialed if the main number is busy of if there is no answer.rw
DisplayString
.1.3.6.1.4.1.434.2.2.4.16.5.1.3
dialerV25bisAnsEnableStates whether or not the dialer answers incoming calls.rw
FalseTrue
.1.3.6.1.4.1.434.2.2.4.16.5.1.4
dialerV25bisRetryAllowedIndicates whether or not the dialer will try to redial a number that is busy or does not answer.ro
FalseTrue
.1.3.6.1.4.1.434.2.2.4.16.5.1.5
dialerV25bisMaxRetriesSpecifies how many times a number will be redialed if it is busy or otherwise unresponsive.ro
INTEGER
.1.3.6.1.4.1.434.2.2.4.16.5.1.6
dialerV25bisRetryDelayThe amount of time in msecs between redial attempts.ro
INTEGER
.1.3.6.1.4.1.434.2.2.4.16.5.1.7
dialerV25bisConnDelayMaximum delay for connection establishment (secs).ro
INTEGER
.1.3.6.1.4.1.434.2.2.4.16.5.1.8
dialerV25bisOnOffDelayThe delay allowed in seconds for the DSR to go off before hangup.ro
INTEGER
.1.3.6.1.4.1.434.2.2.4.16.5.1.9
dialerV25bisLossDelayAmount of delay in msecs before DSR debouncing for OFF.ro
INTEGER
.1.3.6.1.4.1.434.2.2.4.16.5.1.10
dialerV25bisMinDsrOnDelayAmount of delay in msecs before DSR debouncing for ON.ro
INTEGER
.1.3.6.1.4.1.434.2.2.4.16.5.1.11
dialerV25bisRiDtrDelayAmount of delay in msec before raising DTR when RING occurs.ro
INTEGER
.1.3.6.1.4.1.434.2.2.4.16.5.1.12
dialerV25bisHangupDelayAmount of delay in secs before hangup, if DSR goes OFF in connected state.ro
INTEGER
.1.3.6.1.4.1.434.2.2.4.16.5.1.13
dialerV25bisDeltaRiDelayDelay in msecs before rings are no longer occur.ro
INTEGER
.1.3.6.1.4.1.434.2.2.4.16.5.1.14
dialerV25bisCtsOnDelayMaximum delay in msecs for sending a message to the modem.ro
INTEGER
.1.3.6.1.4.1.434.2.2.4.16.5.1.15
dialerV25bisDtrSignalDTR status.ro
OnOff
.1.3.6.1.4.1.434.2.2.4.16.5.1.16
dialerV25bisDsrSignalDSR status.ro
OnOff
.1.3.6.1.4.1.434.2.2.4.16.5.1.17
dialerV25bisCtsSignalCTS status.ro
OnOff
.1.3.6.1.4.1.434.2.2.4.16.5.1.18
dialerV25bisRiSignalRI status.ro
OnOff
.1.3.6.1.4.1.434.2.2.4.16.5.1.19
dialerV25bisStateThe status of the V.25bis modem: on-hook (1) - Modem not active ready (2) - Connection established dialing (3) - Dialing a number connect (4) - Successful dial attemp data-tran (5) - Data transfer state enabled retrying (6) - Awaiting call attempt ringing (7) - Incoming call present ans-start (8) - Connect request received ans-cplt (9) - Call establised. hanging-up (10) - Dialer disconnecting from DCE ignore-ring (11) - Ringing signal ignored collision (12) - Collision between connection request and incoming call ans-accepting (13) - Accepted incoming call prog-rdy (14) - Dialer ready to communicate with modem program (15) - Modem ready to communicate with dialer prog-ring (16) - Signal detected from DCE prog-not-rdy (17) - Dialer not ready to communicate with modem.ro
Enumeration
.1.3.6.1.4.1.434.2.2.4.16.5.1.20
dialerAtCmdInfoTableGeneral Information Table for AT-CMD dialer.
SEQUENCE OF DialerAtCmdInfoEntry
.1.3.6.1.4.1.434.2.2.4.16.6
dialerAtCmdInfoEntryThe set of dialer configuration attributes for one port.
DialerAtCmdInfoEntry
.1.3.6.1.4.1.434.2.2.4.16.6.1
dialerAtCmdPortRefThe Port Number.ro
PortRef
.1.3.6.1.4.1.434.2.2.4.16.6.1.1
dialerAtCmdPrimaryNumThe main telephone number stored in the dialer.rw
DisplayString
.1.3.6.1.4.1.434.2.2.4.16.6.1.2
dialerAtCmdSecondaryNumThe alternate telephone number stored in the dialer. This number is dialed if the main number is busy or if there is no answer.rw
DisplayString
.1.3.6.1.4.1.434.2.2.4.16.6.1.3
dialerAtCmdAnsEnableStates whether or not the dialer answers incoming calls.rw
FalseTrue
.1.3.6.1.4.1.434.2.2.4.16.6.1.4
dialerAtCmdRetryAllowedIndicates whether or not the dialer will try to redial a number that is busy or does not answer.ro
FalseTrue
.1.3.6.1.4.1.434.2.2.4.16.6.1.5
dialerAtCmdMaxRetriesSpecifies how many times a number will be redialed if it is busy or otherwise unresponsive.ro
INTEGER
.1.3.6.1.4.1.434.2.2.4.16.6.1.6
dialerAtCmdRetryDelayThe amount of time in msecs between redial attempts.ro
INTEGER
.1.3.6.1.4.1.434.2.2.4.16.6.1.7
dialerAtCmdConnDelayMaximum delay for connection establishment (secs).ro
INTEGER
.1.3.6.1.4.1.434.2.2.4.16.6.1.8
dialerAtCmdOnOffDelayThe delay allowed in seconds for the DSR signal to go off before hangup.ro
INTEGER
.1.3.6.1.4.1.434.2.2.4.16.6.1.9
dialerAtCmdLossDelayNumber of msecs allowed before DSR debouncing for OFF.ro
INTEGER
.1.3.6.1.4.1.434.2.2.4.16.6.1.10
dialerAtCmdMinDsrOnDelaymsecs DSR debouncing for ON before going OFF.ro
INTEGER
.1.3.6.1.4.1.434.2.2.4.16.6.1.11
dialerAtCmdRiDtrDelayAmount of delay in msec, before raising DTR when RING occurs.ro
INTEGER
.1.3.6.1.4.1.434.2.2.4.16.6.1.12
dialerAtCmdHangupDelayAmount of delay in secs before hangup, if DSR goes OFF in connected state.ro
INTEGER
.1.3.6.1.4.1.434.2.2.4.16.6.1.13
dialerAtCmdDeltaRiDelaydelay in msecs before rings no longer occur.ro
INTEGER
.1.3.6.1.4.1.434.2.2.4.16.6.1.14
dialerAtCmdParityThe parity.ro
Enumeration
.1.3.6.1.4.1.434.2.2.4.16.6.1.15
dialerAtCmdBitsPerByteThe number of data bits per byte.ro
Enumeration
.1.3.6.1.4.1.434.2.2.4.16.6.1.16
dialerAtCmdModemSpeedModem Speed.ro
INTEGER
.1.3.6.1.4.1.434.2.2.4.16.6.1.17
dialerAtCmdDtrSignalDTR status.ro
OnOff
.1.3.6.1.4.1.434.2.2.4.16.6.1.18
dialerAtCmdDsrSignalDSR status.ro
OnOff
.1.3.6.1.4.1.434.2.2.4.16.6.1.19
dialerAtCmdRiSignalRI status.ro
OnOff
.1.3.6.1.4.1.434.2.2.4.16.6.1.20
dialerAtCmdStateThe status of the AT modem: on-hook (1) - modem not active dialing (2) - dialing a number answering (3) - accepting call from remote ringing (4) - incoming call present retrying (5) - awaiting new call attempt off-hook (6) - Modem active hanging-up (7) - Disconnecting from DCEro
Enumeration
.1.3.6.1.4.1.434.2.2.4.16.6.1.21
dialerV22BisDnaInfoTableGeneral Information Table for V22BISDNA dialer.
SEQUENCE OF DialerV22BisDnaInfoEntry
.1.3.6.1.4.1.434.2.2.4.16.7
dialerV22BisDnaInfoEntryThe set of dialer configuration attributes for one port.
DialerV22BisDnaInfoEntry
.1.3.6.1.4.1.434.2.2.4.16.7.1
dialerV22BisDnaPortRefThe Port Number.ro
PortRef
.1.3.6.1.4.1.434.2.2.4.16.7.1.1
dialerV22BisDnaPrimaryNumThe main telephone number stored in the dialer.rw
DisplayString
.1.3.6.1.4.1.434.2.2.4.16.7.1.2
dialerV22BisDnaSecondaryNumThe alternate telephone number stored in the dialer. This number is dialed if the main number is busy or if there is no answer.rw
DisplayString
.1.3.6.1.4.1.434.2.2.4.16.7.1.3
dialerV22BisDnaAnsEnableStates whether or not the dialer answers incoming calls.rw
FalseTrue
.1.3.6.1.4.1.434.2.2.4.16.7.1.4
dialerV22BisDnaRetryAllowedIndicates whether or not the dialer will try to redial a number that is busy or does not answer.ro
FalseTrue
.1.3.6.1.4.1.434.2.2.4.16.7.1.5
dialerV22BisDnaMaxRetriesSpecifies how many times a number will be redialed if it is busy or otherwise unresponsive.ro
INTEGER
.1.3.6.1.4.1.434.2.2.4.16.7.1.6
dialerV22BisDnaCallProgressCall progress tone detection.ro
FalseTrue
.1.3.6.1.4.1.434.2.2.4.16.7.1.7
dialerV22BisDnaDecadicIndicates whether Decadic dialing is active or not. Decadic dialing does the following: each digit you dial is subtracted from 10, and the result is the number actually dialed.ro
FalseTrue
.1.3.6.1.4.1.434.2.2.4.16.7.1.8
dialerV22BisDnaMakeBreakRatioRatio for PULSE and DIAL make and break time.ro
INTEGER
.1.3.6.1.4.1.434.2.2.4.16.7.1.9
dialerV22BisDnaRetryDelayThe amount of time in msecs between redial attempts.ro
INTEGER
.1.3.6.1.4.1.434.2.2.4.16.7.1.10
dialerV22BisDnaMinDialDelayThe length of delay (msec) associated with a comma placed in a dialing command.ro
INTEGER
.1.3.6.1.4.1.434.2.2.4.16.7.1.11
dialerV22BisDnaWaitDialToneThe amount of time (msec) the modem waits when it encounters the wait for dial tone modifier in dial string.ro
INTEGER
.1.3.6.1.4.1.434.2.2.4.16.7.1.12
dialerV22BisDnaWaitCarrierThe amount of time (msec) the modem waits for valid carrier after completing a dial.ro
INTEGER
.1.3.6.1.4.1.434.2.2.4.16.7.1.13
dialerV22BisDnaHndshkAbortTimerThe amount of time (sec) allowed before the call is aborted if DSR does not go ON.ro
INTEGER
.1.3.6.1.4.1.434.2.2.4.16.7.1.14
dialerV22BisDnaGuardToneIndicates a guard tone frequency.ro
INTEGER
.1.3.6.1.4.1.434.2.2.4.16.7.1.15
dialerV22BisDnaPulseDelayThe delay (msec) between digits dialed on a pulse line.ro
INTEGER
.1.3.6.1.4.1.434.2.2.4.16.7.1.16
dialerV22BisDnaDTMFDurationThe tone duration (msec) used in DMTF dialing.ro
INTEGER
.1.3.6.1.4.1.434.2.2.4.16.7.1.17
dialerV22BisDnaDTMFDelayThe delay (msec) between digits dialed when in tone dial mode.ro
INTEGER
.1.3.6.1.4.1.434.2.2.4.16.7.1.18
dialerV22BisDnaDTMFLevelThe tone dialing level attenuation in dB.ro
INTEGER
.1.3.6.1.4.1.434.2.2.4.16.7.1.19
dialerV22BisDnaTxLevelThe attenuation level (Db) on data transmission, once the handshake is completed with the remote modem.ro
INTEGER
.1.3.6.1.4.1.434.2.2.4.16.7.1.20
dialerV22BisDnaRxLevelMinimum acceptable receiver threshold value. This indicates whether a 3dB attenuation is used on the receive signal at line input.ro
FalseTrue
.1.3.6.1.4.1.434.2.2.4.16.7.1.21
dialerV22BisDnaRiNbrThe number of rings required before the modem answers, if it is set to auto-answer mode.ro
INTEGER
.1.3.6.1.4.1.434.2.2.4.16.7.1.22
dialerV22BisDnaDeltaRiDelaydelay in msecs before rings no longer occur.ro
INTEGER
.1.3.6.1.4.1.434.2.2.4.16.7.1.23
dialerV22BisDnaRiDtrDelayAmount of delay in msec, before raising DTR when RING occurs.ro
INTEGER
.1.3.6.1.4.1.434.2.2.4.16.7.1.24
dialerV22BisDnaDsrRtsDelayDelay between arrival of DSR and activation of RTS circuit in msec.ro
INTEGER
.1.3.6.1.4.1.434.2.2.4.16.7.1.25
dialerV22BisDnaModemSpeedModem Speed.ro
INTEGER
.1.3.6.1.4.1.434.2.2.4.16.7.1.26
dialerV22BisDnaDtrSignalDTR status.ro
OnOff
.1.3.6.1.4.1.434.2.2.4.16.7.1.27
dialerV22BisDnaDsrSignalDSR status.ro
OnOff
.1.3.6.1.4.1.434.2.2.4.16.7.1.28
dialerV22BisDnaRiSignalRI status.ro
OnOff
.1.3.6.1.4.1.434.2.2.4.16.7.1.29
dialerV22BisDnaCdSignalCarrier detect status.ro
OnOff
.1.3.6.1.4.1.434.2.2.4.16.7.1.30
dialerV22BisDnaToneIndTone indication.ro
OnOff
.1.3.6.1.4.1.434.2.2.4.16.7.1.31
dialerV22BisDnaDloIndDial line occupied indication.ro
OnOff
.1.3.6.1.4.1.434.2.2.4.16.7.1.32
dialerV22BisDnaStateStatus of the V22bis Dna modem: dialing-phone (1) - Dialing a number on the phone attached to the DNA phone plug. dialing-mdm (2) - Dialing a remote modem retrying (3) - Awaiting call attempt ringing (4) - Incoming call present line-busy (5) - Busy signal encountered off-hook (6) - Modem active on-hook (7) - Modem not active answering (8) - Accepting call from remote delaying (9) - Waiting for timer to expire voice-com (10) - the line is already used by a voice connection. handshaking (11) - Synchronizing calls with remote wait-ringback (12) - Awaiting remote response initialising (13) - initializing modemro
Enumeration
.1.3.6.1.4.1.434.2.2.4.16.7.1.33
dialerV22BisImcInfoTableGeneral Information Table for V22BISIMC dialer.
SEQUENCE OF DialerV22BisImcInfoEntry
.1.3.6.1.4.1.434.2.2.4.16.8
dialerV22BisImcInfoEntryThe set of dialer configuration attributes for one port.
DialerV22BisImcInfoEntry
.1.3.6.1.4.1.434.2.2.4.16.8.1
dialerV22BisImcPortRefThe Port Number.ro
PortRef
.1.3.6.1.4.1.434.2.2.4.16.8.1.1
dialerV22BisImcPrimaryNumThe main telephone number stored in the dialer.rw
DisplayString
.1.3.6.1.4.1.434.2.2.4.16.8.1.2
dialerV22BisImcSecondaryNumThe alternate telephone number stored in the dialer. This number is dialed if the main number is busy or if there is no answer.rw
DisplayString
.1.3.6.1.4.1.434.2.2.4.16.8.1.3
dialerV22BisImcAnsEnableStates whether or not the dialer answers incoming calls.rw
FalseTrue
.1.3.6.1.4.1.434.2.2.4.16.8.1.4
dialerV22BisImcRetryAllowedIndicates whether or not the dialer will try to redial a number that is busy or does not answer.ro
FalseTrue
.1.3.6.1.4.1.434.2.2.4.16.8.1.5
dialerV22BisImcMaxRetriesSpecifies how many times a number will be redialed if it is busy or otherwise unresponsive.ro
INTEGER
.1.3.6.1.4.1.434.2.2.4.16.8.1.6
dialerV22BisImcCallProgressCall progress tone detection.ro
FalseTrue
.1.3.6.1.4.1.434.2.2.4.16.8.1.7
dialerV22BisImcDecadicIndicates whether Decadic dialing is active or not. Decadic dialing does the following: each digit you dial is subtracted from 10, and the result is the number actually dialed.ro
FalseTrue
.1.3.6.1.4.1.434.2.2.4.16.8.1.8
dialerV22BisImcMakeBreakRatioRatio of PULSE and DIAL make and break time.ro
INTEGER
.1.3.6.1.4.1.434.2.2.4.16.8.1.9
dialerV22BisImcRetryDelayThe amount of time in msecs between redial attempts.ro
INTEGER
.1.3.6.1.4.1.434.2.2.4.16.8.1.10
dialerV22BisImcMinDialDelayThe length of delay (msec) associated with a comma placed in a dialing command.ro
INTEGER
.1.3.6.1.4.1.434.2.2.4.16.8.1.11
dialerV22BisImcWaitDialToneThe amount of time (msec) the modem waits when it encounters the wait for dial tone modifier in dial string.ro
INTEGER
.1.3.6.1.4.1.434.2.2.4.16.8.1.12
dialerV22BisImcWaitCarrierThe amount of time (msec) the modem waits for valid carrier after completing a dial.ro
INTEGER
.1.3.6.1.4.1.434.2.2.4.16.8.1.13
dialerV22BisImcHndshkAbortTimerThe amount of time (sec) allowed before the call is aborted if DSR does not go ON.ro
INTEGER
.1.3.6.1.4.1.434.2.2.4.16.8.1.14
dialerV22BisImcGuardToneIndicates a guard tone frequency.ro
INTEGER
.1.3.6.1.4.1.434.2.2.4.16.8.1.15
dialerV22BisImcPulseDelayThe delay between (msec) digits dialed on a pulse line.ro
INTEGER
.1.3.6.1.4.1.434.2.2.4.16.8.1.16
dialerV22BisImcDTMFDurationThe tone (msec) duration used in DMTF dialing.ro
INTEGER
.1.3.6.1.4.1.434.2.2.4.16.8.1.17
dialerV22BisImcDTMFDelayThe delay (msec) between digits dialed when in tone dial mode.ro
INTEGER
.1.3.6.1.4.1.434.2.2.4.16.8.1.18
dialerV22BisImcDTMFLevelThe tone dialing level attenuation in dB.ro
INTEGER
.1.3.6.1.4.1.434.2.2.4.16.8.1.19
dialerV22BisImcTxLevelThe attenuation level (Db) on data transmission, once the handshake is completed with the remote modem.ro
INTEGER
.1.3.6.1.4.1.434.2.2.4.16.8.1.20
dialerV22BisImcRxLevelMinimum acceptable receiver threshold value. This indicates whether a 3dB attenuation is used on the receive signal at line input.ro
INTEGER
.1.3.6.1.4.1.434.2.2.4.16.8.1.21
dialerV22BisImcRiNbrThe numbet of rings required before the modem answers, if it is set to auto-answer mode.ro
INTEGER
.1.3.6.1.4.1.434.2.2.4.16.8.1.22
dialerV22BisImcDeltaRiDelaydelay in msecs before rings no longer occur.ro
INTEGER
.1.3.6.1.4.1.434.2.2.4.16.8.1.23
dialerV22BisImcRiDtrDelayAmount of delay in msec, before raising DTR when RING occurs.ro
INTEGER
.1.3.6.1.4.1.434.2.2.4.16.8.1.24
dialerV22BisImcDsrRtsDelayDelay between arrival of DSR and activation of RTS circuit in msec.ro
INTEGER
.1.3.6.1.4.1.434.2.2.4.16.8.1.25
dialerV22BisImcModemSpeedModem Speed.ro
INTEGER
.1.3.6.1.4.1.434.2.2.4.16.8.1.26
dialerV22BisImcDtrSignalDTR status.ro
OnOff
.1.3.6.1.4.1.434.2.2.4.16.8.1.27
dialerV22BisImcDsrSignalDSR status.ro
OnOff
.1.3.6.1.4.1.434.2.2.4.16.8.1.28
dialerV22BisImcRiSignalRI status.ro
OnOff
.1.3.6.1.4.1.434.2.2.4.16.8.1.29
dialerV22BisImcCdSignalCarrier Detect status.ro
OnOff
.1.3.6.1.4.1.434.2.2.4.16.8.1.30
dialerV22BisImcToneIndTone indication.ro
OnOff
.1.3.6.1.4.1.434.2.2.4.16.8.1.31
dialerV22BisImcDloIndDial line occupied indication.ro
OnOff
.1.3.6.1.4.1.434.2.2.4.16.8.1.32
dialerV22BisImcLineTypeStates whether the modem is connected to a Leased or Dial-Up phone line.ro
Enumeration
.1.3.6.1.4.1.434.2.2.4.16.8.1.33
dialerV22BisImcLeasedOpertnThis applies to Leased line type only. This field states whether the dialer will go off-hook in Originate or Answer mode.ro
Enumeration
.1.3.6.1.4.1.434.2.2.4.16.8.1.34
dialerV22BisImcSpeakerLevelThe volume level of the Eiconcard's speaker.ro
Enumeration
.1.3.6.1.4.1.434.2.2.4.16.8.1.35
dialerV22BisImcStateStatus of the V22bis Imc modem: dialing-phone (1) - Dialing a number on the phone attached to the DNA phone plug. dialing-mdm (2) - Dialing a remote modem retrying (3) - Awaiting call attempt ringing (4) - Incoming call present line-busy (5) - Busy signal encountered off-hook (6) - Modem active on-hook (7) - Modem not active answering (8) - Accepting call from remote delaying (9) - Waiting for timer to expire voice-com (10) - the line is already used by a voice connection. handshaking (11) - Syncronizing calls with remote wait-ringback (12) - Awaiting remote response initialising (13) - initializing modemro
Enumeration
.1.3.6.1.4.1.434.2.2.4.16.8.1.36
dialerV32BisInfoTableGeneral Information Table for V32Bis dialer.
SEQUENCE OF DialerV32BisInfoEntry
.1.3.6.1.4.1.434.2.2.4.16.9
dialerV32BisInfoEntryThe set of dialer configuration attributes for one port.
DialerV32BisInfoEntry
.1.3.6.1.4.1.434.2.2.4.16.9.1
dialerV32BisPortRefThe Port Number.ro
PortRef
.1.3.6.1.4.1.434.2.2.4.16.9.1.1
dialerV32BisPrimNumThe main telephone number stored in the dialer.rw
DisplayString
.1.3.6.1.4.1.434.2.2.4.16.9.1.2
dialerV32BisSecNumThe alternate telephone number stored in the dialer. This number is dialed if the main number is busy or if there is no answer.rw
DisplayString
.1.3.6.1.4.1.434.2.2.4.16.9.1.3
dialerV32BisOverrNumOverride number.ro
DisplayString
.1.3.6.1.4.1.434.2.2.4.16.9.1.4
dialerV32BisCurrNumCurrent number.ro
DisplayString
.1.3.6.1.4.1.434.2.2.4.16.9.1.5
dialerV32BisPrimBitRateDefault bit rate for primary number.ro
PrimBitRate
.1.3.6.1.4.1.434.2.2.4.16.9.1.6
dialerV32BisSecBitRateDefault bit rate for secondary number.ro
PrimBitRate
.1.3.6.1.4.1.434.2.2.4.16.9.1.7
dialerV32BisOverrBitRateDefault bit rate for override number.ro
PrimBitRate
.1.3.6.1.4.1.434.2.2.4.16.9.1.8
dialerV32BisCurrBitRateDefault bit rate for current number.ro
PrimBitRate
.1.3.6.1.4.1.434.2.2.4.16.9.1.9
dialerV32BisPrimConfigDial modem primary configurationro
PrimCfg
.1.3.6.1.4.1.434.2.2.4.16.9.1.10
dialerV32BisSecConfigDial modem secondary configurationro
PrimCfg
.1.3.6.1.4.1.434.2.2.4.16.9.1.11
dialerV32BisOverrConfigDial modem override configurationro
PrimCfg
.1.3.6.1.4.1.434.2.2.4.16.9.1.12
dialerV32BisCurrConfigDial modem current configurationro
PrimCfg
.1.3.6.1.4.1.434.2.2.4.16.9.1.13
dialerV32BisCurrRetryCurrent number of retries.ro
INTEGER
.1.3.6.1.4.1.434.2.2.4.16.9.1.14
dialerV32BisRingCountIncoming ring counter.ro
INTEGER
.1.3.6.1.4.1.434.2.2.4.16.9.1.15
dialerV32BisAnsEnableStates whether or not the dialer answers incoming calls.rw
FalseTrue
.1.3.6.1.4.1.434.2.2.4.16.9.1.16
dialerV32BisDialMethodThe method used for dialing.ro
Enumeration
.1.3.6.1.4.1.434.2.2.4.16.9.1.17
dialerV32BisRetryIndicates whether or not the dialer will try to redial a number that is busy or does not answer.ro
FalseTrue
.1.3.6.1.4.1.434.2.2.4.16.9.1.18
dialerV32BisCallFailureReason for last call failure.ro
INTEGER
.1.3.6.1.4.1.434.2.2.4.16.9.1.19
dialerV32BisCarrierDetectDelay in msec to wait for verification of carrier detect.ro
INTEGER
.1.3.6.1.4.1.434.2.2.4.16.9.1.20
dialerV32BisCarrierWaitDelay in msec to wait for carrier detect.ro
INTEGER
.1.3.6.1.4.1.434.2.2.4.16.9.1.21
dialerV32BisHangupVerifyDelay in msec to wait to verify for hangup.ro
INTEGER
.1.3.6.1.4.1.434.2.2.4.16.9.1.22
dialerV32BisHangupSignalHangup signal state.ro
DisEnable
.1.3.6.1.4.1.434.2.2.4.16.9.1.23
dialerV32BisTxLevelThe attenuation level (Db) on data transmission, once the handshake is completed with the remote modem.ro
INTEGER
.1.3.6.1.4.1.434.2.2.4.16.9.1.24
dialerV32BisRxLevelMinimum acceptable receiver threshold value. This indicates whether a 3dB attenuation is used on the receive signal at line input.ro
INTEGER
.1.3.6.1.4.1.434.2.2.4.16.9.1.25
dialerV32BisGuardToneIndicates a guard tone frequency.ro
INTEGER
.1.3.6.1.4.1.434.2.2.4.16.9.1.26
dialerV32BisLeasedLineDial or leased line.ro
Enumeration
.1.3.6.1.4.1.434.2.2.4.16.9.1.27
dialerV32BisLeaseModeThis applies to Leased line type only. This field states whether the dialer will go off-hook in Originate or Answer mode.ro
Enumeration
.1.3.6.1.4.1.434.2.2.4.16.9.1.28
dialerV32BisLLTxLevelThe attenuation level (Db) on data transmission once the handshake is completed with the remote modem (for leased line).ro
INTEGER
.1.3.6.1.4.1.434.2.2.4.16.9.1.29
dialerV32BisLLConfigLeased line configurationro
PrimCfg
.1.3.6.1.4.1.434.2.2.4.16.9.1.30
dialerV32BisLLBitRateLeased line bit rate.ro
PrimBitRate
.1.3.6.1.4.1.434.2.2.4.16.9.1.31
dialerV32BisCallingToneCalling tone state.ro
DisEnable
.1.3.6.1.4.1.434.2.2.4.16.9.1.32
dialerV32BisAutoModeAuto mode state (fallback/forward).ro
DisEnable
.1.3.6.1.4.1.434.2.2.4.16.9.1.33
dialerV32BisRetryAllowedIndicates whether or not the dialer will try to redial a number that is busy or does not answer.ro
DisEnable
.1.3.6.1.4.1.434.2.2.4.16.9.1.34
dialerV32BisMaxRetrySpecifies how many times a number will be redialed if it is busy or otherwise unresponsive.ro
INTEGER
.1.3.6.1.4.1.434.2.2.4.16.9.1.35
dialerV32BisDialToneThe dial tone state.ro
DisEnable
.1.3.6.1.4.1.434.2.2.4.16.9.1.36
dialerV32BisDialToneWaitThe amount of time (msec) the modem waits when it encounters the wait for dial tone modifier in dial string.ro
INTEGER
.1.3.6.1.4.1.434.2.2.4.16.9.1.37
dialerV32BisRetryWaitRetry timer delay.ro
INTEGER
.1.3.6.1.4.1.434.2.2.4.16.9.1.38
dialerV32BisHangupWaitHangup timer delay.ro
INTEGER
.1.3.6.1.4.1.434.2.2.4.16.9.1.39
dialerV32BisDialPauseWaitmaximum delay before dial.ro
INTEGER
.1.3.6.1.4.1.434.2.2.4.16.9.1.40
dialerV32BisDeltaRiWaitMaximum delay (msec) between 2 rings.ro
INTEGER
.1.3.6.1.4.1.434.2.2.4.16.9.1.41
dialerV32BisDTMFDurationThe tone duration (msec) used in DMTF dialing.ro
INTEGER
.1.3.6.1.4.1.434.2.2.4.16.9.1.42
dialerV32BisDTMFDelayThe delay (msec) between digits dialed when in tone dial mode.ro
INTEGER
.1.3.6.1.4.1.434.2.2.4.16.9.1.43
dialerV32BisDTMFFreq1LevelDTMF high frequency power level.ro
INTEGER
.1.3.6.1.4.1.434.2.2.4.16.9.1.44
dialerV32BisDTMFFreq2LevelDTMF low frequency power level.ro
INTEGER
.1.3.6.1.4.1.434.2.2.4.16.9.1.45
dialerV32BisPulseMakeTimePulse make time (msec).ro
INTEGER
.1.3.6.1.4.1.434.2.2.4.16.9.1.46
dialerV32BisPulseBreakTimePulse break time (msec).ro
INTEGER
.1.3.6.1.4.1.434.2.2.4.16.9.1.47
dialerV32BisPulseDelayPulse interdigit delay (msec).ro
INTEGER
.1.3.6.1.4.1.434.2.2.4.16.9.1.48
dialerV32BisSpeakerLevelThe volume level of the Eiconcard's speaker.ro
Enumeration
.1.3.6.1.4.1.434.2.2.4.16.9.1.49
dialerV32BisRiToAnswerNumber of rings befor answering.ro
INTEGER
.1.3.6.1.4.1.434.2.2.4.16.9.1.50
dialerV32BisAnswerBitRateAnswer bit rate.ro
PrimBitRate
.1.3.6.1.4.1.434.2.2.4.16.9.1.51
dialerV32BisAnswerConfigAnswer configuration.ro
PrimCfg
.1.3.6.1.4.1.434.2.2.4.16.9.1.52
dialerV32BisRetrain.ro
OnOff
.1.3.6.1.4.1.434.2.2.4.16.9.1.53
dialerV32BisEqmLevel.ro
Enumeration
.1.3.6.1.4.1.434.2.2.4.16.9.1.54
dialerV32BisRiOnOffDetectRing signal status.ro
OnOff
.1.3.6.1.4.1.434.2.2.4.16.9.1.55
dialerV32BisCdDetectCarrier detect status.ro
OnOff
.1.3.6.1.4.1.434.2.2.4.16.9.1.56
dialerV32BisRingbackDetectRingback signal detect status.ro
OnOff
.1.3.6.1.4.1.434.2.2.4.16.9.1.57
dialerV32BisAnswerDetectAnswer tone detect status.ro
OnOff
.1.3.6.1.4.1.434.2.2.4.16.9.1.58
dialerV32BisBusyDetectBusy tone detect status.ro
OnOff
.1.3.6.1.4.1.434.2.2.4.16.9.1.59
dialerV32BisDiscDetectDisconnect detect status.ro
OnOff
.1.3.6.1.4.1.434.2.2.4.16.9.1.60
dialerV32BisCdSignalCD signal status.ro
OnOff
.1.3.6.1.4.1.434.2.2.4.16.9.1.61
dialerV32BisDsrSignalDSR signal status.ro
OnOff
.1.3.6.1.4.1.434.2.2.4.16.9.1.62
dialerV32BisStateState of the V32bis dialer: m-closed (1) - Dialer not active m-opened (2) - No connection establised m-local-test (3) - Local analog loopback m-ringing (4) - Incoming call present m-dialing (5) - Dialing a number m-answering (6) - Call answer in progress m-originating (7) - Call originate in progress m-retrying (8) - Awaiting call attempt m-connected (9) - connection present m-retraining (10) - performing retrain m-remote-test (11) - Remote digital loopback m-remote-disc (12) - Remote has disconnected m-local-disc (13) - Local has disconnected m-hangup-idle (14) - Idle after hangup m-closing (15) - Awaiting local disconnect m-offhook-idle (16) - Modem goes off hook on commandro
Enumeration
.1.3.6.1.4.1.434.2.2.4.16.9.1.63
dialerControlTableThe table for dynamic dialing entries.
SEQUENCE OF DialerControlEntry
.1.3.6.1.4.1.434.2.2.4.16.10
dialerControlEntryThe set of attributes for one entry per port.
DialerControlEntry
.1.3.6.1.4.1.434.2.2.4.16.10.1
dialerCtrlPortRefThe Port number of the dialer.ro
PortRef
.1.3.6.1.4.1.434.2.2.4.16.10.1.1
dialerCtrlActionThe Action states. exec (1) - This action executes the script file which would be set in dialerCtrlScriptFile. dial (2) - This action dials the number stored in dialerCtrlMainNumber. if dialerCtrlMainNumber is not set then the dialerCtrlPrimary number is dialed by the dialer. ISDN dialer dials the number stored by the card. hangup (3) - This action hangs-up the current connection. store (6) - This action stores the parameters in the card. ISDN dialer only.rw
Enumeration
.1.3.6.1.4.1.434.2.2.4.16.10.1.2
dialerCtrlAnsEnableStates whether or not the dialer answers incoming calls.rw
FalseTrue
.1.3.6.1.4.1.434.2.2.4.16.10.1.3
dialerCtrlDirectDSROnOffDefines the setting of the Data Rate Select signal. Setting this mib is valid only if the dialer type is Direct and the interface is RS-232.rw
OnOff
.1.3.6.1.4.1.434.2.2.4.16.10.1.4
dialerCtrlNumberThe primary Phone Numberrw
DisplayString
.1.3.6.1.4.1.434.2.2.4.16.10.1.5
dialerCtrlScriptFileThe Complete path where the Dialer Script file resides.rw
DisplayString
.1.3.6.1.4.1.434.2.2.4.16.10.1.6
dialerCtrlActionStateThe state of the action operation performed by the Agent as a result of setting the values to the dialerCtrlAction. The Management station will poll that variable after initiating an action. The value done(1) indicates that the action terminated successfully. The value failed(2) indicates that the action terminated with an error. The variable dialerCtrlActionError indicates the error code.ro
ActionState
.1.3.6.1.4.1.434.2.2.4.16.10.1.7
dialerCtrlActionErrorIf the value is 0, this means no error. Otherwise, the value indicates the error code returned after the action operation.ro
INTEGER
.1.3.6.1.4.1.434.2.2.4.16.10.1.8
dialerCtrlConfigThe config to which the V32 dialer will have to be set. This information is only used when using a V32 dialer.rw
PrimCfg
.1.3.6.1.4.1.434.2.2.4.16.10.1.9
dialerCtrlBitRateThe Bit Rate to which the V32 dialer will have to be set. This information is only used when using a V32 dialer.rw
PrimBitRate
.1.3.6.1.4.1.434.2.2.4.16.10.1.10
dialerCtrlTypeThe remote directory number type. Used by ISDN dialer only. DEFINED ONLY FOR TESTS.rw
IsdnDnType
.1.3.6.1.4.1.434.2.2.4.16.10.1.11
dialerCtrlPlanThe remote directory number plan. Used by ISDN dialer only. DEFINED ONLY FOR TESTS.rw
IsdnDnPlan
.1.3.6.1.4.1.434.2.2.4.16.10.1.12
dialerCtrlSubThe remote subaddress. When in the connected state, the remote subaddress dialer is displayed. Otherwise, the stored subaddress is displayed. Used by ISDN dialer only. DEFINED ONLY FOR TESTS.rw
DisplayString
.1.3.6.1.4.1.434.2.2.4.16.10.1.13
dialerCtrlSubTypeThe local subaddress type. Used by ISDN dialer only. DEFINED ONLY FOR TESTS.rw
IsdnSubType
.1.3.6.1.4.1.434.2.2.4.16.10.1.14
dialerCtrlTnsThe string identifying the selected long distance carrier. In ISDN terms, it is called the Transit Network Selection. This string is usually made of 3 digits and is assigned by Bellcore. Used by ISDN dialer only. DEFINED ONLY FOR TESTS.rw
DisplayString
.1.3.6.1.4.1.434.2.2.4.16.10.1.15
dialerCtrlNumberTempThe temporary Phone Number. DEFINED ONLY FOR ISDN TESTS.ro
DisplayString
.1.3.6.1.4.1.434.2.2.4.16.10.1.16
dialerCtrlDialMaskRead the mask state. DEFINED ONLY FOR TESTS.ro
INTEGER
.1.3.6.1.4.1.434.2.2.4.16.10.1.17
dialerCtrlCallSpeedRead the mask state. DEFINED ONLY FOR TESTS.ro
INTEGER
.1.3.6.1.4.1.434.2.2.4.16.10.1.18
dialerIsdnStatusTableThe table for ISDN dialer Status.
SEQUENCE OF DialerIsdnStatusEntry
.1.3.6.1.4.1.434.2.2.4.16.11
dialerIsdnStatusEntryThe set of attributes for one port.
DialerIsdnStatusEntry
.1.3.6.1.4.1.434.2.2.4.16.11.1
dialerIsdnStatusPortRefThe port number for which isdn status is displayed.ro
PortRef
.1.3.6.1.4.1.434.2.2.4.16.11.1.1
dialerIsdnStatusSwitchTypeThe current switch type in use for isdn.ro
Enumeration
.1.3.6.1.4.1.434.2.2.4.16.11.1.2
dialerIsdnStatusChTypeThe isdn channel type, B channel or D channel.ro
Enumeration
.1.3.6.1.4.1.434.2.2.4.16.11.1.3
dialerIsdnStatusL1StateThe current state of layer 1 subsystem.ro
Enumeration
.1.3.6.1.4.1.434.2.2.4.16.11.1.4
dialerIsdnStatusStateThe current state of the ISDN dialer.ro
Enumeration
.1.3.6.1.4.1.434.2.2.4.16.11.1.5
dialerIsdnNI1BChTableThe table for the ISDN NI1 BChannel dialer.
SEQUENCE OF DialerIsdnNI1BChEntry
.1.3.6.1.4.1.434.2.2.4.16.12
dialerIsdnNI1BChEntryThe set of attributes for one port.
DialerIsdnNI1BChEntry
.1.3.6.1.4.1.434.2.2.4.16.12.1
dialerIsdnNI1BChPortRefThe port number which is configured for NI1-BChannel.ro
PortRef
.1.3.6.1.4.1.434.2.2.4.16.12.1.1
dialerIsdnNI1BChSpidThe Terminal's Service Profile IDentification.ro
DisplayString
.1.3.6.1.4.1.434.2.2.4.16.12.1.2
dialerIsdnNI1BChSpidStatusThe current SPID status.ro
IsdnSpidStatus
.1.3.6.1.4.1.434.2.2.4.16.12.1.3
dialerIsdnNI1BChLocalDnThe local directory number type.ro
DisplayString
.1.3.6.1.4.1.434.2.2.4.16.12.1.4
dialerIsdnNI1BChLocalSubThe local subaddress.ro
DisplayString
.1.3.6.1.4.1.434.2.2.4.16.12.1.5
dialerIsdnNI1BChTnsDigsThe string identifying the selected long distance carrier. In ISDN terms, it is called the Transit Network Selection. This string is usually made of 3 digits and is assigned by Bellcore.rw
DisplayString
.1.3.6.1.4.1.434.2.2.4.16.12.1.6
dialerIsdnNI1BChRemoteDnWhen in the connected state, the number dialed is displayed. Otherwise, the stored number is displayed.rw
DisplayString
.1.3.6.1.4.1.434.2.2.4.16.12.1.7
dialerIsdnNI1BChRemoteSubWhen in the connected state, the remote subaddress dialer is displayed. Otherwise, the stored subaddress is displayed.rw
DisplayString
.1.3.6.1.4.1.434.2.2.4.16.12.1.8
dialerIsdnNI1BChCallTypeThe current call type.ro
IsdnCallType
.1.3.6.1.4.1.434.2.2.4.16.12.1.9
dialerIsdnNI1BChCallSpeedThe current call speed.rw
IsdnCallSpeed
.1.3.6.1.4.1.434.2.2.4.16.12.1.10
dialerIsdnNI1BChBChannelThe current B channel connected to.ro
IsdnBChannels
.1.3.6.1.4.1.434.2.2.4.16.12.1.11
dialerIsdnNI1BChAnsEnableAnswer Enable Status.ro
IsdnAnsEnable
.1.3.6.1.4.1.434.2.2.4.16.12.1.12
dialerIsdnNI1BChCcStateThe state of call control subsystem.ro
IsdnNI1BCcState
.1.3.6.1.4.1.434.2.2.4.16.12.1.13
dialerIsdnNI1BChCcNbCauseThe number of causes saved.ro
INTEGER
.1.3.6.1.4.1.434.2.2.4.16.12.1.14
dialerIsdnNI1BChCcCauseLast causes saved.ro
OCTET STRING
.1.3.6.1.4.1.434.2.2.4.16.12.1.15
dialerIsdnNI1BChL3StateThe state of layer 3 subsystem.ro
IsdnL3State
.1.3.6.1.4.1.434.2.2.4.16.12.1.16
dialerIsdnNI1BChL2StateThe state of layer 2 subsystem.ro
IsdnL2State
.1.3.6.1.4.1.434.2.2.4.16.12.1.17
dialerIsdnNI1BChTeiValueThe value of the terminal is dynamic TEI.ro
INTEGER
.1.3.6.1.4.1.434.2.2.4.16.12.1.18
dialerIsdnNI1BChTeiStatusThe status of the terminal's dynamic TEI.ro
IsdnTeiStatus
.1.3.6.1.4.1.434.2.2.4.16.12.1.19
dialerIsdnNI1BChLocalDnTypeThe local directory number type.ro
IsdnDnType
.1.3.6.1.4.1.434.2.2.4.16.12.1.20
dialerIsdnNI1BChLocalDnPlanThe local directory number plan.ro
IsdnDnPlan
.1.3.6.1.4.1.434.2.2.4.16.12.1.21
dialerIsdnNI1BChLocalSubTypeThe local subaddress type.ro
IsdnSubType
.1.3.6.1.4.1.434.2.2.4.16.12.1.22
dialerIsdnNI1BChTnsNetIdThe transit network id.ro
IsdnTnsNetId
.1.3.6.1.4.1.434.2.2.4.16.12.1.23
dialerIsdnNI1BChTnsIdPlanThe transit network plan.ro
IsdnTnsIdPlan
.1.3.6.1.4.1.434.2.2.4.16.12.1.24
dialerIsdnNI1BChRemoteDnTypeThe remote directory number type.rw
IsdnDnType
.1.3.6.1.4.1.434.2.2.4.16.12.1.25
dialerIsdnNI1BChRemoteDnPlanThe remote directory number plan.rw
IsdnDnPlan
.1.3.6.1.4.1.434.2.2.4.16.12.1.26
dialerIsdnNI1BChRemoteSubTypeThe local subaddress type.rw
IsdnSubType
.1.3.6.1.4.1.434.2.2.4.16.12.1.27
dialerIsdnNI1BChScrStatusThe status of call screening.ro
IsdnScrStatus
.1.3.6.1.4.1.434.2.2.4.16.12.1.28
dialerIsdnNI1BChCallOptThe current call option.ro
IsdnCallOpt
.1.3.6.1.4.1.434.2.2.4.16.12.1.29
dialerIsdnNI1BChStoDefinedThe validity of sto- elements.ro
IsdnStoDefined
.1.3.6.1.4.1.434.2.2.4.16.12.1.30
dialerIsdnNI1BChStoDnTypeThe stored directory number type.ro
INTEGER
.1.3.6.1.4.1.434.2.2.4.16.12.1.31
dialerIsdnNI1BChStoDnPlanThe stored directory number plan.ro
INTEGER
.1.3.6.1.4.1.434.2.2.4.16.12.1.32
dialerIsdnNI1BChStoDnThe stored directory number.ro
DisplayString
.1.3.6.1.4.1.434.2.2.4.16.12.1.33
dialerIsdnNI1BChStoSubTypeThe stored subaddress type.ro
INTEGER
.1.3.6.1.4.1.434.2.2.4.16.12.1.34
dialerIsdnNI1BChStoSubThe stored subaddress.ro
DisplayString
.1.3.6.1.4.1.434.2.2.4.16.12.1.35
dialerIsdnNI1BChStoTnsNetIdThe stored transit network id.ro
INTEGER
.1.3.6.1.4.1.434.2.2.4.16.12.1.36
dialerIsdnNI1BChStoTnsPlanThe stored transit network plan.ro
INTEGER
.1.3.6.1.4.1.434.2.2.4.16.12.1.37
dialerIsdnNI1BChStoDigsThe stored transit network address.ro
DisplayString
.1.3.6.1.4.1.434.2.2.4.16.12.1.38
dialerIsdnNI1BChStoBcTypeThe stored bearer cap. type.ro
INTEGER
.1.3.6.1.4.1.434.2.2.4.16.12.1.39
dialerIsdnNI1BChStoBcOptThe stored bearer cap. option.ro
INTEGER
.1.3.6.1.4.1.434.2.2.4.16.12.1.40
dialerIsdnNI1DChTableThe table for the ISDN NI1 DChannel dialer.
SEQUENCE OF DialerIsdnNI1DChEntry
.1.3.6.1.4.1.434.2.2.4.16.13
dialerIsdnNI1DChEntryThe set of attributes for one port.
DialerIsdnNI1DChEntry
.1.3.6.1.4.1.434.2.2.4.16.13.1
dialerIsdnNI1DChPortRefThe port number configured for the NI1 DChannel.ro
PortRef
.1.3.6.1.4.1.434.2.2.4.16.13.1.1
dialerIsdnNI1DChTeiValueThe static TEI value on the D Channel for data communications.ro
INTEGER
.1.3.6.1.4.1.434.2.2.4.16.13.1.2
dialerIsdnNI1DChTeiStatusThe status of TEI - always ASSIGNED.ro
IsdnTeiStatus
.1.3.6.1.4.1.434.2.2.4.16.13.1.3
dialerIsdnNI1DChL2StateThe current layer 2 state.ro
IsdnL2State
.1.3.6.1.4.1.434.2.2.4.16.13.1.4
dialerIsdnNI1DChP3StateThe current Packet layer state.ro
IsdnP3State
.1.3.6.1.4.1.434.2.2.4.16.13.1.5
dialerIsdnNI1DChActStateThe current activation FSM state.ro
IsdnActState
.1.3.6.1.4.1.434.2.2.4.16.13.1.6
dialerIsdnTR6BChTableThe table for the ISDN TR6 BChannel dialer.
SEQUENCE OF DialerIsdnTR6BChEntry
.1.3.6.1.4.1.434.2.2.4.16.14
dialerIsdnTR6BChEntryThe set of attributes for one port.
DialerIsdnTR6BChEntry
.1.3.6.1.4.1.434.2.2.4.16.14.1
dialerIsdnTR6BChPortRefThe port number for which the 1TR6 BChannel info is displayed.ro
PortRef
.1.3.6.1.4.1.434.2.2.4.16.14.1.1
dialerIsdnTR6BChLocalDnThe local directory number type.ro
DisplayString
.1.3.6.1.4.1.434.2.2.4.16.14.1.2
dialerIsdnTR6BChRemoteDnWhen in the connected state, the number dialed is displayed. Otherwise, the stored number is displayed.rw
DisplayString
.1.3.6.1.4.1.434.2.2.4.16.14.1.3
dialerIsdnTR6BChCallTypeThe current call type.ro
IsdnCallType
.1.3.6.1.4.1.434.2.2.4.16.14.1.4
dialerIsdnTR6BChCallSpeedThe current call speed.rw
IsdnCallSpeed
.1.3.6.1.4.1.434.2.2.4.16.14.1.5
dialerIsdnTR6BChBChannelThe current B Channel connected to.ro
IsdnBChannels
.1.3.6.1.4.1.434.2.2.4.16.14.1.6
dialerIsdnTR6BChAnsEnableAnswer enable status.ro
IsdnAnsEnable
.1.3.6.1.4.1.434.2.2.4.16.14.1.7
dialerIsdnTR6BChCcStateThe state of call control subsystem.ro
IsdnTR6BCcState
.1.3.6.1.4.1.434.2.2.4.16.14.1.8
dialerIsdnTR6BChCcNbCauseThe number of causes saved.ro
INTEGER
.1.3.6.1.4.1.434.2.2.4.16.14.1.9
dialerIsdnTR6BChCcCauseLast causes saved.ro
OCTET STRING
.1.3.6.1.4.1.434.2.2.4.16.14.1.10
dialerIsdnTR6BChL3StateThe state of layer 3 subsystem.ro
IsdnL3State
.1.3.6.1.4.1.434.2.2.4.16.14.1.11
dialerIsdnTR6BChL2StateThe state of layer 2 subsystem.ro
IsdnL2State
.1.3.6.1.4.1.434.2.2.4.16.14.1.12
dialerIsdnTR6BChLocalDnTypeThe local directory number type.ro
IsdnDnType
.1.3.6.1.4.1.434.2.2.4.16.14.1.13
dialerIsdnTR6BChLocalDnPlanThe local directory number plan.ro
IsdnDnPlan
.1.3.6.1.4.1.434.2.2.4.16.14.1.14
dialerIsdnTR6BChRemoteDnTypeThe remote directory number type.rw
IsdnDnType
.1.3.6.1.4.1.434.2.2.4.16.14.1.15
dialerIsdnTR6BChRemoteDnPlanThe remote directory number plan.rw
IsdnDnPlan
.1.3.6.1.4.1.434.2.2.4.16.14.1.16
dialerIsdnTR6BChScrStatusThe status of call screening.ro
IsdnScrStatus
.1.3.6.1.4.1.434.2.2.4.16.14.1.17
dialerIsdnTR6BChCallOptThe current call option.ro
IsdnCallOpt
.1.3.6.1.4.1.434.2.2.4.16.14.1.18
dialerIsdnTR6BChTeiValueThe static TEI value on the D Channel for data communications.ro
INTEGER
.1.3.6.1.4.1.434.2.2.4.16.14.1.19
dialerIsdnTR6BChTeiStatusThe status of TEI - always ASSIGNED.ro
IsdnTeiStatus
.1.3.6.1.4.1.434.2.2.4.16.14.1.20
dialerIsdnTR6BChStoDefinedThe validity of sto- elements.ro
IsdnStoDefined
.1.3.6.1.4.1.434.2.2.4.16.14.1.21
dialerIsdnTR6BChStoDnTypeThe stored directory number type.ro
INTEGER
.1.3.6.1.4.1.434.2.2.4.16.14.1.22
dialerIsdnTR6BChStoDnPlanThe stored directory number plan.ro
INTEGER
.1.3.6.1.4.1.434.2.2.4.16.14.1.23
dialerIsdnTR6BChStoDnThe stored directory number.ro
DisplayString
.1.3.6.1.4.1.434.2.2.4.16.14.1.24
dialerIsdnTR6BChStoBcTypeThe stored bearer cap. type.ro
INTEGER
.1.3.6.1.4.1.434.2.2.4.16.14.1.25
dialerIsdnTR6BChStoBcOptThe stored bearer cap. option.ro
INTEGER
.1.3.6.1.4.1.434.2.2.4.16.14.1.26
dialerIsdnVN3BChTableThe table for the ISDN VN3 BChannel dialer.
SEQUENCE OF DialerIsdnVN3BChEntry
.1.3.6.1.4.1.434.2.2.4.16.15
dialerIsdnVN3BChEntryThe set of attributes for one port.
DialerIsdnVN3BChEntry
.1.3.6.1.4.1.434.2.2.4.16.15.1
dialerIsdnVN3BChPortRefThe port number for which the VN3 BChannel info is displayed.ro
PortRef
.1.3.6.1.4.1.434.2.2.4.16.15.1.1
dialerIsdnVN3BChLocalDnTypeThe local directory number type.ro
IsdnDnType
.1.3.6.1.4.1.434.2.2.4.16.15.1.2
dialerIsdnVN3BChLocalDnPlanThe local directory number plan.ro
IsdnDnPlan
.1.3.6.1.4.1.434.2.2.4.16.15.1.3
dialerIsdnVN3BChLocalDnThe local directory number type.ro
DisplayString
.1.3.6.1.4.1.434.2.2.4.16.15.1.4
dialerIsdnVN3BChLocalSubTypeThe local subaddress type.ro
IsdnSubType
.1.3.6.1.4.1.434.2.2.4.16.15.1.5
dialerIsdnVN3BChLocalSubThe local directory number type.ro
DisplayString
.1.3.6.1.4.1.434.2.2.4.16.15.1.6
dialerIsdnVN3BChRemoteDnTypeThe local directory number type.rw
IsdnDnType
.1.3.6.1.4.1.434.2.2.4.16.15.1.7
dialerIsdnVN3BChRemoteDnPlanThe local directory number plan.rw
IsdnDnPlan
.1.3.6.1.4.1.434.2.2.4.16.15.1.8
dialerIsdnVN3BChRemoteDnThe local directory number type.rw
DisplayString
.1.3.6.1.4.1.434.2.2.4.16.15.1.9
dialerIsdnVN3BChRemoteSubTypeThe local subaddress type.rw
IsdnSubType
.1.3.6.1.4.1.434.2.2.4.16.15.1.10
dialerIsdnVN3BChRemoteSubThe local directory number type.rw
DisplayString
.1.3.6.1.4.1.434.2.2.4.16.15.1.11
dialerIsdnVN3BChCallTypeThe current call type.ro
IsdnCallType
.1.3.6.1.4.1.434.2.2.4.16.15.1.12
dialerIsdnVN3BChCallSpeedThe current call speed.rw
IsdnCallSpeed
.1.3.6.1.4.1.434.2.2.4.16.15.1.13
dialerIsdnVN3BChBChannelThe current B Channel connected to.ro
IsdnBChannels
.1.3.6.1.4.1.434.2.2.4.16.15.1.14
dialerIsdnVN3BChAnsEnableAnswer enable status.ro
IsdnAnsEnable
.1.3.6.1.4.1.434.2.2.4.16.15.1.15
dialerIsdnVN3BChScrStatusThe status of call screening.ro
IsdnScrStatus
.1.3.6.1.4.1.434.2.2.4.16.15.1.16
dialerIsdnVN3BChCallOptThe current call option.ro
IsdnCallOpt
.1.3.6.1.4.1.434.2.2.4.16.15.1.17
dialerIsdnVN3BChCcStateThe state of call control subsystem.ro
IsdnVN3BCcState
.1.3.6.1.4.1.434.2.2.4.16.15.1.18
dialerIsdnVN3BChCcNbCauseThe number of causes saved.ro
INTEGER
.1.3.6.1.4.1.434.2.2.4.16.15.1.19
dialerIsdnVN3BChCcCauseLast causes saved.ro
OCTET STRING
.1.3.6.1.4.1.434.2.2.4.16.15.1.20
dialerIsdnVN3BChL3StateThe state of layer 3 subsystem.ro
IsdnL3State
.1.3.6.1.4.1.434.2.2.4.16.15.1.21
dialerIsdnVN3BChL2StateThe state of layer 2 subsystem.ro
IsdnL2State
.1.3.6.1.4.1.434.2.2.4.16.15.1.22
dialerIsdnVN3BChTeiValueThe static TEI value on the D Channel for data communications.ro
INTEGER
.1.3.6.1.4.1.434.2.2.4.16.15.1.23
dialerIsdnVN3BChTeiStatusThe status of TEI - always ASSIGNED.ro
IsdnTeiStatus
.1.3.6.1.4.1.434.2.2.4.16.15.1.24
dialerIsdnVN3BChStoDefinedThe validity of sto- elements.ro
IsdnStoDefined
.1.3.6.1.4.1.434.2.2.4.16.15.1.25
dialerIsdnVN3BChStoDnTypeThe stored directory number type.ro
INTEGER
.1.3.6.1.4.1.434.2.2.4.16.15.1.26
dialerIsdnVN3BChStoDnPlanThe stored directory number plan.ro
INTEGER
.1.3.6.1.4.1.434.2.2.4.16.15.1.27
dialerIsdnVN3BChStoDnThe stored directory number.ro
DisplayString
.1.3.6.1.4.1.434.2.2.4.16.15.1.28
dialerIsdnVN3BChStoSubTypeThe stored subaddress type.ro
INTEGER
.1.3.6.1.4.1.434.2.2.4.16.15.1.29
dialerIsdnVN3BChStoSubThe stored subaddress.ro
DisplayString
.1.3.6.1.4.1.434.2.2.4.16.15.1.30
dialerIsdnVN3BChStoBcTypeThe stored bearer cap type.ro
INTEGER
.1.3.6.1.4.1.434.2.2.4.16.15.1.31
dialerIsdnVN3BChStoBcOptThe stored bearer cap option.ro
INTEGER
.1.3.6.1.4.1.434.2.2.4.16.15.1.32
dialerIsdnVN3DChTableThe table for the ISDN VN3 DChannel dialer.
SEQUENCE OF DialerIsdnVN3DChEntry
.1.3.6.1.4.1.434.2.2.4.16.16
dialerIsdnVN3DChEntryThe set of attributes for one port.
DialerIsdnVN3DChEntry
.1.3.6.1.4.1.434.2.2.4.16.16.1
dialerIsdnVN3DChPortRefThe port number for which the VN3 DChannel info is displayed.ro
PortRef
.1.3.6.1.4.1.434.2.2.4.16.16.1.1
dialerIsdnVN3DChTeiValueThe static TEI value on the D Channel for data communications.ro
INTEGER
.1.3.6.1.4.1.434.2.2.4.16.16.1.2
dialerIsdnVN3DChTeiStatusThe status of TEI - always ASSIGNED.ro
IsdnTeiStatus
.1.3.6.1.4.1.434.2.2.4.16.16.1.3
dialerIsdnVN3DChL2StateThe state of layer 2 subsystem.ro
IsdnL2State
.1.3.6.1.4.1.434.2.2.4.16.16.1.4
dialerIsdnVN3DChP3StateThe current Packet layer state.ro
IsdnP3State
.1.3.6.1.4.1.434.2.2.4.16.16.1.5
dialerIsdnNET3BChTableThe table for the ISDN NET3 BChannel dialer.
SEQUENCE OF DialerIsdnNET3BChEntry
.1.3.6.1.4.1.434.2.2.4.16.17
dialerIsdnNET3BChEntryThe set of attributes for one port.
DialerIsdnNET3BChEntry
.1.3.6.1.4.1.434.2.2.4.16.17.1
dialerIsdnNET3BChPortRefThe port number for which the NET3 BChannel info is displayed.ro
PortRef
.1.3.6.1.4.1.434.2.2.4.16.17.1.1
dialerIsdnNET3BChLocalDnTypeThe local directory number type.ro
IsdnDnType
.1.3.6.1.4.1.434.2.2.4.16.17.1.2
dialerIsdnNET3BChLocalDnPlanThe local directory number plan.ro
IsdnDnPlan
.1.3.6.1.4.1.434.2.2.4.16.17.1.3
dialerIsdnNET3BChLocalDnThe local directory number type.ro
DisplayString
.1.3.6.1.4.1.434.2.2.4.16.17.1.4
dialerIsdnNET3BChLocalSubTypeThe local subaddress type.ro
IsdnSubType
.1.3.6.1.4.1.434.2.2.4.16.17.1.5
dialerIsdnNET3BChLocalSubThe local directory number type.ro
DisplayString
.1.3.6.1.4.1.434.2.2.4.16.17.1.6
dialerIsdnNET3BChRemoteDnTypeThe local directory number type.rw
IsdnDnType
.1.3.6.1.4.1.434.2.2.4.16.17.1.7
dialerIsdnNET3BChRemoteDnPlanThe local directory number plan.rw
IsdnDnPlan
.1.3.6.1.4.1.434.2.2.4.16.17.1.8
dialerIsdnNET3BChRemoteDnThe local directory number type.rw
DisplayString
.1.3.6.1.4.1.434.2.2.4.16.17.1.9
dialerIsdnNET3BChRemoteSubTypeThe local subaddress type.rw
IsdnSubType
.1.3.6.1.4.1.434.2.2.4.16.17.1.10
dialerIsdnNET3BChRemoteSubThe local directory number type.rw
DisplayString
.1.3.6.1.4.1.434.2.2.4.16.17.1.11
dialerIsdnNET3BChCallTypeThe current call type.ro
IsdnCallType
.1.3.6.1.4.1.434.2.2.4.16.17.1.12
dialerIsdnNET3BChCallSpeedThe current call speed.rw
IsdnCallSpeed
.1.3.6.1.4.1.434.2.2.4.16.17.1.13
dialerIsdnNET3BChBChannelThe current B Channel connected to.ro
IsdnBChannels
.1.3.6.1.4.1.434.2.2.4.16.17.1.14
dialerIsdnNET3BChAnsEnableAnswer enable status.ro
IsdnAnsEnable
.1.3.6.1.4.1.434.2.2.4.16.17.1.15
dialerIsdnNET3BChTnsNetIdThe transit network id.ro
IsdnTnsNetId
.1.3.6.1.4.1.434.2.2.4.16.17.1.16
dialerIsdnNET3BChTnsIdPlanThe transit network plan.ro
IsdnTnsIdPlan
.1.3.6.1.4.1.434.2.2.4.16.17.1.17
dialerIsdnNET3BChTnsDigsThe string identifying the selected long distance carrier. In ISDN terms, it is called the Transit Network Selection. This string is usually made of 3 digits and is assigned by Bellcore.rw
DisplayString
.1.3.6.1.4.1.434.2.2.4.16.17.1.18
dialerIsdnNET3BChScrStatusThe status of call screening.ro
IsdnScrStatus
.1.3.6.1.4.1.434.2.2.4.16.17.1.19
dialerIsdnNET3BChCallOptThe current call option.ro
IsdnCallOpt
.1.3.6.1.4.1.434.2.2.4.16.17.1.20
dialerIsdnNET3BChCcStateThe state of call control subsystem.ro
IsdnNET3BCcState
.1.3.6.1.4.1.434.2.2.4.16.17.1.21
dialerIsdnNET3BChCcNbCauseThe number of causes saved.ro
INTEGER
.1.3.6.1.4.1.434.2.2.4.16.17.1.22
dialerIsdnNET3BChCcCauseLast causes saved.ro
OCTET STRING
.1.3.6.1.4.1.434.2.2.4.16.17.1.23
dialerIsdnNET3BChL3StateThe state of layer 3 subsystem.ro
IsdnL3State
.1.3.6.1.4.1.434.2.2.4.16.17.1.24
dialerIsdnNET3BChL2StateThe state of layer 2 subsystem.ro
IsdnL2State
.1.3.6.1.4.1.434.2.2.4.16.17.1.25
dialerIsdnNET3BChTeiValueThe static TEI value on the D Channel for data communications.ro
INTEGER
.1.3.6.1.4.1.434.2.2.4.16.17.1.26
dialerIsdnNET3BChTeiStatusThe status of TEI - always ASSIGNED.ro
IsdnTeiStatus
.1.3.6.1.4.1.434.2.2.4.16.17.1.27
dialerIsdnNET3BChStoDefinedThe validity of sto- elements.ro
IsdnStoDefined
.1.3.6.1.4.1.434.2.2.4.16.17.1.28
dialerIsdnNET3BChStoDnTypeThe stored directory number type.ro
INTEGER
.1.3.6.1.4.1.434.2.2.4.16.17.1.29
dialerIsdnNET3BChStoDnPlanThe stored directory number plan.ro
INTEGER
.1.3.6.1.4.1.434.2.2.4.16.17.1.30
dialerIsdnNET3BChStoDnThe stored directory number.ro
DisplayString
.1.3.6.1.4.1.434.2.2.4.16.17.1.31
dialerIsdnNET3BChStoSubTypeThe stored subaddress type.ro
INTEGER
.1.3.6.1.4.1.434.2.2.4.16.17.1.32
dialerIsdnNET3BChStoSubThe stored subaddress.ro
DisplayString
.1.3.6.1.4.1.434.2.2.4.16.17.1.33
dialerIsdnNET3BChStoTnsNetIdThe stored transit network id.ro
INTEGER
.1.3.6.1.4.1.434.2.2.4.16.17.1.34
dialerIsdnNET3BChStoTnsPlanThe stored transit network plan.ro
INTEGER
.1.3.6.1.4.1.434.2.2.4.16.17.1.35
dialerIsdnNET3BChStoDigsThe stored transit network address.ro
DisplayString
.1.3.6.1.4.1.434.2.2.4.16.17.1.36
dialerIsdnNET3BChStoBcTypeThe stored bearer cap. type.ro
INTEGER
.1.3.6.1.4.1.434.2.2.4.16.17.1.37
dialerIsdnNET3BChStoBcOptThe stored bearer cap. option.ro
INTEGER
.1.3.6.1.4.1.434.2.2.4.16.17.1.38
dialerIsdnTPHBChTableThe table for the ISDN TPH BChannel dialer.
SEQUENCE OF DialerIsdnTPHBChEntry
.1.3.6.1.4.1.434.2.2.4.16.18
dialerIsdnTPHBChEntryThe set of attributes for one port.
DialerIsdnTPHBChEntry
.1.3.6.1.4.1.434.2.2.4.16.18.1
dialerIsdnTPHBChPortRefThe port number for which the TPH BChannel info is displayed.ro
PortRef
.1.3.6.1.4.1.434.2.2.4.16.18.1.1
dialerIsdnTPHBChLocalDnTypeThe local directory number type.ro
IsdnDnType
.1.3.6.1.4.1.434.2.2.4.16.18.1.2
dialerIsdnTPHBChLocalDnPlanThe local directory number plan.ro
IsdnDnPlan
.1.3.6.1.4.1.434.2.2.4.16.18.1.3
dialerIsdnTPHBChLocalDnThe local directory number type.ro
DisplayString
.1.3.6.1.4.1.434.2.2.4.16.18.1.4
dialerIsdnTPHBChLocalSubTypeThe local subaddress type.ro
IsdnSubType
.1.3.6.1.4.1.434.2.2.4.16.18.1.5
dialerIsdnTPHBChLocalSubThe local directory number type.ro
DisplayString
.1.3.6.1.4.1.434.2.2.4.16.18.1.6
dialerIsdnTPHBChRemoteDnTypeThe local directory number type.rw
IsdnDnType
.1.3.6.1.4.1.434.2.2.4.16.18.1.7
dialerIsdnTPHBChRemoteDnPlanThe local directory number plan.rw
IsdnDnPlan
.1.3.6.1.4.1.434.2.2.4.16.18.1.8
dialerIsdnTPHBChRemoteDnThe local directory number type.rw
DisplayString
.1.3.6.1.4.1.434.2.2.4.16.18.1.9
dialerIsdnTPHBChRemoteSubTypeThe local subaddress type.rw
IsdnSubType
.1.3.6.1.4.1.434.2.2.4.16.18.1.10
dialerIsdnTPHBChRemoteSubThe local directory number type.rw
DisplayString
.1.3.6.1.4.1.434.2.2.4.16.18.1.11
dialerIsdnTPHBChCallTypeThe current call type.ro
IsdnCallType
.1.3.6.1.4.1.434.2.2.4.16.18.1.12
dialerIsdnTPHBChCallSpeedThe current call speed.rw
IsdnCallSpeed
.1.3.6.1.4.1.434.2.2.4.16.18.1.13
dialerIsdnTPHBChBChannelThe current B Channel connected to.ro
IsdnBChannels
.1.3.6.1.4.1.434.2.2.4.16.18.1.14
dialerIsdnTPHBChAnsEnableAnswer enable status.ro
IsdnAnsEnable
.1.3.6.1.4.1.434.2.2.4.16.18.1.15
dialerIsdnTPHBChScrStatusThe status of call screening.ro
IsdnScrStatus
.1.3.6.1.4.1.434.2.2.4.16.18.1.16
dialerIsdnTPHBChCallOptThe current call option.ro
IsdnCallOpt
.1.3.6.1.4.1.434.2.2.4.16.18.1.17
dialerIsdnTPHBChCcStateThe state of call control subsystem.ro
IsdnTPHBCcState
.1.3.6.1.4.1.434.2.2.4.16.18.1.18
dialerIsdnTPHBChCcNbCauseThe number of causes saved.ro
INTEGER
.1.3.6.1.4.1.434.2.2.4.16.18.1.19
dialerIsdnTPHBChCcCauseLast causes saved.ro
OCTET STRING
.1.3.6.1.4.1.434.2.2.4.16.18.1.20
dialerIsdnTPHBChL3StateThe state of layer 3 subsystem.ro
IsdnL3State
.1.3.6.1.4.1.434.2.2.4.16.18.1.21
dialerIsdnTPHBChL2StateThe state of layer 2 subsystem.ro
IsdnL2State
.1.3.6.1.4.1.434.2.2.4.16.18.1.22
dialerIsdnTPHBChTeiValueThe static TEI value on the D Channel for data communications.ro
INTEGER
.1.3.6.1.4.1.434.2.2.4.16.18.1.23
dialerIsdnTPHBChTeiStatusThe status of TEI - always ASSIGNED.ro
IsdnTeiStatus
.1.3.6.1.4.1.434.2.2.4.16.18.1.24
dialerIsdnTPHBChStoDefinedThe validity of sto- elements.ro
IsdnStoDefined
.1.3.6.1.4.1.434.2.2.4.16.18.1.25
dialerIsdnTPHBChStoDnTypeThe stored directory number type.ro
INTEGER
.1.3.6.1.4.1.434.2.2.4.16.18.1.26
dialerIsdnTPHBChStoDnPlanThe stored directory number plan.ro
INTEGER
.1.3.6.1.4.1.434.2.2.4.16.18.1.27
dialerIsdnTPHBChStoDnThe stored directory number.ro
DisplayString
.1.3.6.1.4.1.434.2.2.4.16.18.1.28
dialerIsdnTPHBChStoSubTypeThe stored subaddress type.ro
INTEGER
.1.3.6.1.4.1.434.2.2.4.16.18.1.29
dialerIsdnTPHBChStoSubThe stored subaddress.ro
DisplayString
.1.3.6.1.4.1.434.2.2.4.16.18.1.30
dialerIsdnTPHBChStoBcTypeThe stored bearer cap. type.ro
INTEGER
.1.3.6.1.4.1.434.2.2.4.16.18.1.31
dialerIsdnTPHBChStoBcOptThe stored bearer cap. option.ro
INTEGER
.1.3.6.1.4.1.434.2.2.4.16.18.1.32
dialerIsdnTPHDChTableThe table for the ISDN TPH DChannel dialer.
SEQUENCE OF DialerIsdnTPHDChEntry
.1.3.6.1.4.1.434.2.2.4.16.19
dialerIsdnTPHDChEntryThe set of attributes for one port.
DialerIsdnTPHDChEntry
.1.3.6.1.4.1.434.2.2.4.16.19.1
dialerIsdnTPHDChPortRefThe port number for which the TPH DChannel info is displayed.ro
PortRef
.1.3.6.1.4.1.434.2.2.4.16.19.1.1
dialerIsdnTPHDChTeiValueThe static TEI value on the D Channel for data communications.ro
INTEGER
.1.3.6.1.4.1.434.2.2.4.16.19.1.2
dialerIsdnTPHDChTeiStatusThe status of TEI - always ASSIGNED.ro
IsdnTeiStatus
.1.3.6.1.4.1.434.2.2.4.16.19.1.3
dialerIsdnTPHDChL2StateThe state of layer 2 subsystem.ro
IsdnL2State
.1.3.6.1.4.1.434.2.2.4.16.19.1.4
dialerIsdnTPHDChP3StateThe current Packet layer state.ro
IsdnP3State
.1.3.6.1.4.1.434.2.2.4.16.19.1.5
EICON-DIALER-MIB - SNMP MIB Reference | MIBs Explorer