DVB-MGTR101290-MIB
DVB Measurement Group MIB to support TR 101 290. This tr101290 module contains measurements defined in TR 101 290.
Main OID:
tr101290.1.3.6.1.4.1.2696.3.2
938
Objects
Active
Status
3
Dependencies
Imported Objects
Objects
938 total| Object Name |
|---|
dvb OBJECT IDENTIFIER .1.3.6.1.4.1.2696 |
mg OBJECT IDENTIFIER .1.3.6.1.4.1.2696.3 |
tr101290DVB Measurement Group MIB to support TR 101 290. This tr101290 module contains measurements defined in TR 101 290. MODULE-IDENTITY .1.3.6.1.4.1.2696.3.2 |
tr101290Objects OBJECT IDENTIFIER .1.3.6.1.4.1.2696.3.2.1 |
tr101290Control OBJECT IDENTIFIER .1.3.6.1.4.1.2696.3.2.1.1 |
controlNowThe current date and time at the location of the measurement equipment. It is highly desirable that the offset from UTC should be included. It is possible to set the time and date through this object, but it is expected that most systems will incorporate a more accurate method for doing this.rw DateAndTime (SNMPv2-TC) .1.3.6.1.4.1.2696.3.2.1.1.1 |
controlEventPersistenceThe persistence timer used with Event errors. An Event error test remains in the 'fail' state for this length of time after the occurrence of the Event.rw FloatingPoint UNITS "second" .1.3.6.1.4.1.2696.3.2.1.1.2 |
controlRFSystemTableTable which controls the RF modulation expected to be received on each input. SEQUENCE OF ControlRFSystemEntry .1.3.6.1.4.1.2696.3.2.1.1.3 |
controlRFSystemEntryRow specification ControlRFSystemEntry .1.3.6.1.4.1.2696.3.2.1.1.3.1 |
rfSystemInputNumberRF input whose mode of operation is to be set InputNumber .1.3.6.1.4.1.2696.3.2.1.1.3.1.1 |
rfSystemDeliveryThe type of signal the instrument should expect at its input.rw DeliverySystemType .1.3.6.1.4.1.2696.3.2.1.1.3.1.2 |
controlSynchronizationTableTable reserved for future specification of synchronized timing. SEQUENCE OF ControlSynchronizationEntry .1.3.6.1.4.1.2696.3.2.1.1.4 |
controlSynchronizationEntryRow specification ControlSynchronizationEntry .1.3.6.1.4.1.2696.3.2.1.1.4.1 |
controlSynchronizationInputNumberTransport Stream number to which the objects in this row apply. InputNumber .1.3.6.1.4.1.2696.3.2.1.1.4.1.1 |
controlSynchronizedTimeThis object is reserved pending future standardisation of timestamping of Transport Streams.rw FloatingPoint .1.3.6.1.4.1.2696.3.2.1.1.4.1.2 |
tr101290Trap OBJECT IDENTIFIER .1.3.6.1.4.1.2696.3.2.1.2 |
trapPrefix OBJECT IDENTIFIER .1.3.6.1.4.1.2696.3.2.1.2.0 |
testFailTrapThis trap is sent when a test which is not associated with a measurement fails. This trap is triggered by the transition of the '...State' or '...TestState' object associated with the test to the 'fail' state from any other state. Transmission of the trap is subject to rate control and to the enable status of each test. NOTIFICATION-TYPE .1.3.6.1.4.1.2696.3.2.1.2.0.1 |
measurementFailTrapTrap which is sent when a test which is associated with a measurement fails. This trap is triggered by the transition of the '...State' or '...TestState' object associated with the test to the 'fail' state from any other state. Transmission of the trap is subject to rate control and to the enable status of each test. NOTIFICATION-TYPE .1.3.6.1.4.1.2696.3.2.1.2.0.2 |
measurementUnknownTrapTrap which is sent when a measurement value becomes unavailable. This trap is triggered by the transition of the '...MeasurementState' object associated with the measurement to the 'unknown' state from any other state. Transmission of the trap is subject to rate control. NOTIFICATION-TYPE .1.3.6.1.4.1.2696.3.2.1.2.0.3 |
trapControlTableTable of trap control information for each input SEQUENCE OF TrapControlEntry .1.3.6.1.4.1.2696.3.2.1.2.1 |
trapControlEntryRow specification TrapControlEntry .1.3.6.1.4.1.2696.3.2.1.2.1.1 |
trapControlInputNumberEach Transport Stream input has separate trap control parameters. This object identifies the Transport Stream input to which the trap control parameters apply InputNumber .1.3.6.1.4.1.2696.3.2.1.2.1.1.1 |
trapControlOIDIn the case of a testFailTrap or a measurementFailTrap, this object holds the OID of the '...State' or '...TestState' object whose transition to 'fail' has triggered the trap. In the case of a measurementUnknownTrap, this object holds the OID of the '...MeasurementState' object whose transition to 'unknown' has triggered the trap. This object is present for the formal purpose of defining the variable bindings returned with the traps. It is not accessible for normal reading.ro OBJECT IDENTIFIER .1.3.6.1.4.1.2696.3.2.1.2.1.1.2 |
trapControlGenerationTimeIn the case of a testFailTrap or a measurementFailTrap, at the moment when the trap is generated, the value of the '...LatestError' object associated with the test which caused the trap is copied here. In the case of a measurementUnknownTrap, the time at which the measurement became unknown is copied here. This object is present for the formal purpose of defining the variable bindings returned with the traps. It is not accessible for normal reading.ro DateAndTime (SNMPv2-TC) .1.3.6.1.4.1.2696.3.2.1.2.1.1.3 |
trapControlMeasurementValueAt the moment when a measurementFailTrap is generated, the value of this object is set from the '...Value' object associated with the measurement which caused the trap. Where a measurement returns multiple values, the value which is copied here is the one which is compared with the threshold(s) to generate the test result. The measurement units are the same as those of the source object. This object is present for the formal purpose of defining the variable bindings returned with the traps. It is not accessible for normal reading.ro FloatingPoint .1.3.6.1.4.1.2696.3.2.1.2.1.1.4 |
trapControlRateStatusThis object is used for rate control of traps, preventing overload of the management network by transmission of an excessive number of traps. The value 'disabled' means that traps are never sent. The value 'enabled' means that a trap will be sent when triggered. When a trap is sent, the agent changes the value of this object to 'enabledThrottled'. In this state the agent will not send any more traps. The agent automatically changes the value back to 'enabled' when the time specified by trapControlPeriod expires. A management application may set the value to 'enabled' at any time, but must never set the value to 'enabledThrottled'. This single status applies to all the trap types, so for example if an agent sends a testFailTrap it will not send a measurementFailTrap until the trapControlPeriod expires.rw RateStatus .1.3.6.1.4.1.2696.3.2.1.2.1.1.5 |
trapControlPeriodAn agent will ensure that the interval between sending traps is no shorter than this time period. The management system can override this by setting trapControlRateStatus back to 'enabled' within the time period.rw Unsigned32 .1.3.6.1.4.1.2696.3.2.1.2.1.1.6 |
trapControlFailureSummaryThis bit string contains a summary of all the test failures. If the bit for the test is set to one, that test is in a fail state. When a trap is being generated, the agent should ensure that this information is as up to date as possible, without causing undue delay in sending the trap.ro TestSummary .1.3.6.1.4.1.2696.3.2.1.2.1.1.7 |
trapInputThe Transport Stream input whose change triggered the current trap. This information can also be obtained by analysing the trapControlOID, but trapInput provides the information directly. This object is present for the formal purpose of defining the variable bindings returned with the traps. It is not accessible for normal reading.ro InputNumber .1.3.6.1.4.1.2696.3.2.1.2.2 |
tr101290Capability OBJECT IDENTIFIER .1.3.6.1.4.1.2696.3.2.1.3 |
capabilityMIBRevisionThe capabilities of the agent are expressed in relation to a specific revision of the tr101290 MIB module. The date and time here must exactly match one of the revision dates in the MODULE-IDENTITY section of the MIB.ro DateAndTime (SNMPv2-TC) .1.3.6.1.4.1.2696.3.2.1.3.1 |
capabilityTS OBJECT IDENTIFIER .1.3.6.1.4.1.2696.3.2.1.3.5 |
capabilityTSGroupSpecifies the overall availability of the Transport Stream group of tests and measurements, tr101290TS.ro GroupAvailability .1.3.6.1.4.1.2696.3.2.1.3.5.1 |
capabilityTSTableSpecifies the individual availability of the Transport Stream group of tests and measurements, tr101290TS. SEQUENCE OF CapabilityTSEntry .1.3.6.1.4.1.2696.3.2.1.3.5.2 |
capabilityTSEntryRow specification CapabilityTSEntry .1.3.6.1.4.1.2696.3.2.1.3.5.2.1 |
capabilityTSOIDThe object identifier of a specific test/measurement. The object identifier of the object within the table whose SYNTAX is 'TestState' is used to identify the test/measurement. Table index components of the object identifier are set to zero, except for those which identify specific tests/measurements. Such index objects always have a syntax which begins 'Index...' in this MIB. OBJECT IDENTIFIER .1.3.6.1.4.1.2696.3.2.1.3.5.2.1.1 |
capabilityTSAvailabilityThe availability of a specific test or measurementro Availability .1.3.6.1.4.1.2696.3.2.1.3.5.2.1.2 |
capabilityTSPollIntervalIndicates the interval between updates of the information supplied by this object.ro PollingInterval UNITS "millisecond" .1.3.6.1.4.1.2696.3.2.1.3.5.2.1.3 |
capabilityCableSat OBJECT IDENTIFIER .1.3.6.1.4.1.2696.3.2.1.3.6 |
capabilityCableSatGroupSpecifies the overall availability of the cable and satellite group of tests and measurements, tr101290CableSat.ro GroupAvailability .1.3.6.1.4.1.2696.3.2.1.3.6.1 |
capabilityCableSatTableSpecifies the individual availability of the cable and satellite group of tests and measurements, tr101290CableSat. SEQUENCE OF CapabilityCableSatEntry .1.3.6.1.4.1.2696.3.2.1.3.6.2 |
capabilityCableSatEntryRow specification CapabilityCableSatEntry .1.3.6.1.4.1.2696.3.2.1.3.6.2.1 |
capabilityCableSatOIDThe object identifier of a specific test/measurement. The object identifier of the object within the table whose SYNTAX is 'TestState' is used to identify the test/measurement. Table index components of the object identifier are set to zero, except for those which identify specific tests/measurements. Such index objects always have a syntax which begins 'Index...' in this MIB. OBJECT IDENTIFIER .1.3.6.1.4.1.2696.3.2.1.3.6.2.1.1 |
capabilityCableSatAvailabilityThe availability of a specific test or measurementro Availability .1.3.6.1.4.1.2696.3.2.1.3.6.2.1.2 |
capabilityCableSatPollIntervalIndicates the interval between updates of the information supplied by this object.ro PollingInterval UNITS "millisecond" .1.3.6.1.4.1.2696.3.2.1.3.6.2.1.3 |
capabilityCable OBJECT IDENTIFIER .1.3.6.1.4.1.2696.3.2.1.3.7 |
capabilityCableGroupSpecifies the overall availability of the cable group of tests and measurements, tr101290Cable.ro GroupAvailability .1.3.6.1.4.1.2696.3.2.1.3.7.1 |
capabilityCableTableSpecifies the individual availability of the cable group of tests and measurements, tr101290Cable. SEQUENCE OF CapabilityCableEntry .1.3.6.1.4.1.2696.3.2.1.3.7.2 |
capabilityCableEntryRow specification CapabilityCableEntry .1.3.6.1.4.1.2696.3.2.1.3.7.2.1 |
capabilityCableOIDThe object identifier of a specific test/measurement. The object identifier of the object within the table whose SYNTAX is 'TestState' is used to identify the test/measurement. Table index components of the object identifier are set to zero, except for those which identify specific tests/measurements. Such index objects always have a syntax which begins 'Index...' in this MIB. OBJECT IDENTIFIER .1.3.6.1.4.1.2696.3.2.1.3.7.2.1.1 |
capabilityCableAvailabilityThe availability of a specific test or measurementro Availability .1.3.6.1.4.1.2696.3.2.1.3.7.2.1.2 |
capabilityCablePollIntervalIndicates the interval between updates of the information supplied by this object.ro PollingInterval UNITS "millisecond" .1.3.6.1.4.1.2696.3.2.1.3.7.2.1.3 |
capabilitySatellite OBJECT IDENTIFIER .1.3.6.1.4.1.2696.3.2.1.3.8 |
capabilitySatelliteGroupSpecifies the overall availability of the satellite group of tests and measurements, tr101290Satellite.ro GroupAvailability .1.3.6.1.4.1.2696.3.2.1.3.8.1 |
capabilitySatelliteTableSpecifies the individual availability of the satellite group of tests and measurements, tr101290Satellite. SEQUENCE OF CapabilitySatelliteEntry .1.3.6.1.4.1.2696.3.2.1.3.8.2 |
capabilitySatelliteEntryRow specification CapabilitySatelliteEntry .1.3.6.1.4.1.2696.3.2.1.3.8.2.1 |
capabilitySatelliteOIDThe object identifier of a specific test/measurement. The object identifier of the object within the table whose SYNTAX is 'TestState' is used to identify the test/measurement. Table index components of the object identifier are set to zero, except for those which identify specific tests/measurements. Such index objects always have a syntax which begins 'Index...' in this MIB. OBJECT IDENTIFIER .1.3.6.1.4.1.2696.3.2.1.3.8.2.1.1 |
capabilitySatelliteAvailabilityThe availability of a specific test or measurementro Availability .1.3.6.1.4.1.2696.3.2.1.3.8.2.1.2 |
capabilitySatellitePollIntervalIndicates the interval between updates of the information supplied by this object.ro PollingInterval UNITS "millisecond" .1.3.6.1.4.1.2696.3.2.1.3.8.2.1.3 |
capabilityTerrestrial OBJECT IDENTIFIER .1.3.6.1.4.1.2696.3.2.1.3.9 |
capabilityTerrestrialGroupSpecifies the overall availability of the terrestrial group of tests and measurements, tr101290Terrestrial.ro GroupAvailability .1.3.6.1.4.1.2696.3.2.1.3.9.1 |
capabilityTerrestrialTableSpecifies the individual availability of the terrestrial group of tests and measurements, tr101290Terrestrial. SEQUENCE OF CapabilityTerrestrialEntry .1.3.6.1.4.1.2696.3.2.1.3.9.2 |
capabilityTerrestrialEntryRow specification CapabilityTerrestrialEntry .1.3.6.1.4.1.2696.3.2.1.3.9.2.1 |
capabilityTerrestrialOIDThe object identifier of a specific test/measurement. The object identifier of the object within the table whose SYNTAX is 'TestState' is used to identify the test/measurement. Table index components of the object identifier are set to zero, except for those which identify specific tests/measurements. Such index objects always have a syntax which begins 'Index...' in this MIB. OBJECT IDENTIFIER .1.3.6.1.4.1.2696.3.2.1.3.9.2.1.1 |
capabilityTerrestrialAvailabilityThe availability of a specific test or measurementro Availability .1.3.6.1.4.1.2696.3.2.1.3.9.2.1.2 |
capabilityTerrestrialPollIntervalIndicates the interval between updates of the information supplied by this object.ro PollingInterval UNITS "millisecond" .1.3.6.1.4.1.2696.3.2.1.3.9.2.1.3 |
tr101290TS OBJECT IDENTIFIER .1.3.6.1.4.1.2696.3.2.1.5 |
tsTests OBJECT IDENTIFIER .1.3.6.1.4.1.2696.3.2.1.5.2 |
tsTestsSummaryTableThe tsTestsSummaryTable provides access to the state of all of the Transport Stream tests enumerated in IndexTransportStreamTest. The status relates to the whole Transport Stream. In the case of tests which have a status per PID, the tsTestsSummaryTable gives the 'worst' status across all the PIDs and the status for each PID is available in tsTestsPIDTable. SEQUENCE OF TsTestsSummaryEntry .1.3.6.1.4.1.2696.3.2.1.5.2.2 |
tsTestsSummaryEntryRow specification TsTestsSummaryEntry .1.3.6.1.4.1.2696.3.2.1.5.2.2.1 |
tsTestsSummaryInputNumberTransport Stream on which the test is made InputNumber .1.3.6.1.4.1.2696.3.2.1.5.2.2.1.1 |
tsTestsSummaryTestNumberSpecifies the test, see definition of IndexTransportStreamTest. Rows in the table exist only for tests which are actually implemented by the measuring equipment. IndexTransportStreamTest .1.3.6.1.4.1.2696.3.2.1.5.2.2.1.2 |
tsTestsSummaryStateThis gives the overall pass/fail state of the test. For tests which have a state per PID, tsTestsSummaryState contains the highest numeric value of all the tsTestsPIDState objects for the test.ro TestState .1.3.6.1.4.1.2696.3.2.1.5.2.2.1.3 |
tsTestsSummaryEnableDetermines whether this test and associated traps are enabled. Setting tsTestsSummaryEnable affects tsTestsPIDEnable in tsTestsPIDTable. When tsTestsSummaryEnable is set, all existing instances of tsTestsPIDEnable are set to the same value. Any new rows in tsTestsPIDTable which are created will also have this value for tsTestsPIDEnable (unless the row is created by explicitly setting the value of tsTestsPIDEnable).rw Enable .1.3.6.1.4.1.2696.3.2.1.5.2.2.1.4 |
tsTestsSummaryCounterCount of the number of times this error has occurred. For Status errors this is the number of times the TestState has entered the fail state from some other state. For Error events this is the total number of events; the persistence timer is not taken into account by the counter.ro Counter32 .1.3.6.1.4.1.2696.3.2.1.5.2.2.1.5 |
tsTestsSummaryCounterDiscontinuityProvides the last time at which there was a discontinuity in the tsTestsSummaryCounter object.ro DateAndTime (SNMPv2-TC) .1.3.6.1.4.1.2696.3.2.1.5.2.2.1.6 |
tsTestsSummaryCounterResettsTestsSummaryCounter is reset to zero and tsTestsSummaryCounterDiscontinuity is set to the current time if this object is set to 'true'. This object has no effect on the tsTestsPIDCounter objects.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.2696.3.2.1.5.2.2.1.7 |
tsTestsSummaryLatestErrorThe timestamp at the most recent occurrence of the error. For Status errors this is the most recent time the TestState entered the fail state from some other state. For Error events this is the most recent occurrence; the persistence timer is not taken into account.ro DateAndTime (SNMPv2-TC) .1.3.6.1.4.1.2696.3.2.1.5.2.2.1.8 |
tsTestsSummaryActiveTimeThe total time when it has been possible to evaluate this test.ro ActiveTime UNITS "second" .1.3.6.1.4.1.2696.3.2.1.5.2.2.1.9 |
tsTestsPIDTableThe tsTestsPIDTable provides access to the state of those Transport Stream tests enumerated in IndexTransportStreamTest which relate to individual PIDs. These tests are: 1.4 Continuity_count_error 1.5.a PMT_error_2 1.6 PID_error 2.3.a PCR_repetition_error 2.3.b PCR_discontinuity_indicator_error 2.4 PCR_accuracy_error 2.5 PTS_error 3.3 Buffer_error 3.4.a Unreferenced_PID SEQUENCE OF TsTestsPIDEntry .1.3.6.1.4.1.2696.3.2.1.5.2.3 |
tsTestsPIDEntryRow specification TsTestsPIDEntry .1.3.6.1.4.1.2696.3.2.1.5.2.3.1 |
tsTestsPIDInputNumberTransport Stream on which the test is made InputNumber .1.3.6.1.4.1.2696.3.2.1.5.2.3.1.1 |
tsTestsPIDPIDPID (plus one) on which the test is made PIDPlusOne .1.3.6.1.4.1.2696.3.2.1.5.2.3.1.2 |
tsTestsPIDTestNumberSpecifies the test, see definition of IndexTransportStreamTest. Rows in the table exist only for tests which are actually implemented by the measuring equipment. IndexTransportStreamTest .1.3.6.1.4.1.2696.3.2.1.5.2.3.1.3 |
tsTestsPIDRowStatusThis is used by the manager to create and delete rows in tsTestsPIDTable. The agent automatically creates rows for PID/test combinations where there are errors to report.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.2696.3.2.1.5.2.3.1.4 |
tsTestsPIDStateThis gives the overall pass/fail state of the testro TestState .1.3.6.1.4.1.2696.3.2.1.5.2.3.1.5 |
tsTestsPIDEnableDetermines whether this test and associated traps are enabled. When a trap triggering condition arises for a per PID test, this object alone is used to determine whether a trap will be generated, without any reference to tsTestsSummaryEnable.rw Enable .1.3.6.1.4.1.2696.3.2.1.5.2.3.1.6 |
tsTestsPIDCounterCount of the number of times this error has occurred. For Status errors this is the number of times the TestState has entered the fail state from some other state. For Error events this is the total number of events; the persistence timer is not taken into account by the counter.ro Counter32 .1.3.6.1.4.1.2696.3.2.1.5.2.3.1.7 |
tsTestsPIDCounterDiscontinuityProvides the last time at which there was a discontinuity in the tsTestsSummaryCounter object.ro DateAndTime (SNMPv2-TC) .1.3.6.1.4.1.2696.3.2.1.5.2.3.1.8 |
tsTestsPIDCounterResettsTestsPIDCounter is reset to zero and tsTestsPIDCounterDiscontinuity is set to the current time if 'true' is written to this variable. When read, the value of this object is always 'false'.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.2696.3.2.1.5.2.3.1.9 |
tsTestsPIDLatestErrorThe timestamp at the most recent occurrence of the error. For Status errors this is the most recent time the TestState entered the fail state from some other state. For Error events this is the most recent occurrence; the persistence timer is not taken into account.ro DateAndTime (SNMPv2-TC) .1.3.6.1.4.1.2696.3.2.1.5.2.3.1.10 |
tsTestsPIDActiveTimeThe total time when it has been possible to evaluate this test.ro ActiveTime UNITS "second" .1.3.6.1.4.1.2696.3.2.1.5.2.3.1.11 |
tsTestsPreferences OBJECT IDENTIFIER .1.3.6.1.4.1.2696.3.2.1.5.2.100 |
tsTestsPreferencesTableThis table contains measurement thresholds and other configuration information that is applied on a per Transport Stream basis. SEQUENCE OF TsTestsPreferencesEntry .1.3.6.1.4.1.2696.3.2.1.5.2.100.1 |
tsTestsPreferencesEntryRow specification TsTestsPreferencesEntry .1.3.6.1.4.1.2696.3.2.1.5.2.100.1.1 |
tsTestsPrefInputNumberTransport Stream input to which the preferences apply InputNumber .1.3.6.1.4.1.2696.3.2.1.5.2.100.1.1.1 |
tsTestsPrefTransitionDurationVarious tests, including CAT_error (2.6) and Unreferenced_PID (3.4) must take into account that short transition periods can exist where the state of the SI and PSI information is inconsistent with the state of the stream. These transitions should not cause error indications. This parameter specifies the period which must be allowed for transition states.rw FloatingPoint UNITS "second" .1.3.6.1.4.1.2696.3.2.1.5.2.100.1.1.2 |
tsTestsPrefPATSectionIntervalMaxMaximum repetition interval for PAT sections.rw FloatingPoint UNITS "second" .1.3.6.1.4.1.2696.3.2.1.5.2.100.1.1.3 |
tsTestsPrefPMTSectionIntervalMaxMaximum repetition interval for PMT sections.rw FloatingPoint UNITS "second" .1.3.6.1.4.1.2696.3.2.1.5.2.100.1.1.4 |
tsTestsPrefReferredIntervalMaxMaximum permitted interval between the arrival of consecutive packets for all PIDs. When the value of this object is set, the value of tsTestsPrefPIDReferredIntervalMax is changed for every PID. The value of this object is also used as a default for tsTestsPrefPIDReferredIntervalMax when a new row is created in tsTestsPreferencesPIDTable.rw FloatingPoint UNITS "s" .1.3.6.1.4.1.2696.3.2.1.5.2.100.1.1.5 |
tsTestsPrefPCRIntervalMaxMaximum permitted interval between PCR arrival times on each PCR PID.rw FloatingPoint UNITS "second" .1.3.6.1.4.1.2696.3.2.1.5.2.100.1.1.6 |
tsTestsPrefPCRDiscontinuityMaxMaximum permitted difference between two consecutive PCR values.rw FloatingPoint UNITS "second" .1.3.6.1.4.1.2696.3.2.1.5.2.100.1.1.7 |
tsTestsPrefPCRInaccuracyMaxMaximum permitted PCR inaccuracy. An error is indicated if the PCR inaccuracy is outside the range: [-tsTestsPrefPCRInaccuracyMax .. +tsTestsPrefPCRInaccuracyMax].rw FloatingPoint UNITS "second" .1.3.6.1.4.1.2696.3.2.1.5.2.100.1.1.8 |
tsTestsPrefPTSIntervalMaxMaximum permitted PTS repetition intervalrw FloatingPoint UNITS "second" .1.3.6.1.4.1.2696.3.2.1.5.2.100.1.1.9 |
tsTestsPrefNITActualIntervalMaxMaximum permitted NIT_actual section repetition intervalrw FloatingPoint UNITS "second" .1.3.6.1.4.1.2696.3.2.1.5.2.100.1.1.10 |
tsTestsPrefNITActualIntervalMinMinimum permitted NIT_actual section repetition intervalrw FloatingPoint UNITS "second" .1.3.6.1.4.1.2696.3.2.1.5.2.100.1.1.11 |
tsTestsPrefNITOtherIntervalMaxMaximum permitted NIT_other section repetition intervalrw FloatingPoint UNITS "second" .1.3.6.1.4.1.2696.3.2.1.5.2.100.1.1.12 |
tsTestsPrefSIGapMinMinimum permitted gap between packets containing sections.rw FloatingPoint UNITS "second" .1.3.6.1.4.1.2696.3.2.1.5.2.100.1.1.13 |
tsTestsPrefNITTableIntervalMaxMaximum permitted NIT table repetition intervalrw FloatingPoint UNITS "second" .1.3.6.1.4.1.2696.3.2.1.5.2.100.1.1.14 |
tsTestsPrefBATTableIntervalMaxMaximum permitted BAT table repetition intervalrw FloatingPoint UNITS "second" .1.3.6.1.4.1.2696.3.2.1.5.2.100.1.1.15 |
tsTestsPrefSDTActualTableIntervalMaxMaximum permitted SDT actual transport stream table repetition intervalrw FloatingPoint UNITS "second" .1.3.6.1.4.1.2696.3.2.1.5.2.100.1.1.16 |
tsTestsPrefSDTOtherTableIntervalMaxMaximum permitted SDT other transport stream table repetition intervalrw FloatingPoint UNITS "second" .1.3.6.1.4.1.2696.3.2.1.5.2.100.1.1.17 |
tsTestsPrefEITPFActualTableIntervalMaxMaximum permitted EIT Present/Following actual transport stream table repetition intervalrw FloatingPoint UNITS "second" .1.3.6.1.4.1.2696.3.2.1.5.2.100.1.1.18 |
tsTestsPrefEITPFOtherTableIntervalMaxMaximum permitted EIT Present/Following other transport stream table repetition intervalrw FloatingPoint UNITS "second" .1.3.6.1.4.1.2696.3.2.1.5.2.100.1.1.19 |
tsTestsPrefEITSActualNearTableIntervalMaxMaximum permitted EIT Schedule actual transport stream table repetition interval for the near future (the next 8 days for satellite and cable, the next day for terrestrial).rw FloatingPoint UNITS "second" .1.3.6.1.4.1.2696.3.2.1.5.2.100.1.1.20 |
tsTestsPrefEITSActualFarTableIntervalMaxMaximum permitted EIT Schedule actual transport stream table repetition interval for the far future (beyond the next 8 days for satellite and cable, beyond the next day for terrestrial).rw FloatingPoint UNITS "second" .1.3.6.1.4.1.2696.3.2.1.5.2.100.1.1.21 |
tsTestsPrefEITSOtherNearTableIntervalMaxMaximum permitted EIT Schedule other transport stream table repetition interval for the near future (the next 8 days for satellite and cable, the next day for terrestrial).rw FloatingPoint UNITS "second" .1.3.6.1.4.1.2696.3.2.1.5.2.100.1.1.22 |
tsTestsPrefEITSOtherFarTableIntervalMaxMaximum permitted EIT Schedule other transport stream table repetition interval for the far future (beyond the next 8 days for satellite and cable, beyond the next day for terrestrial).rw FloatingPoint UNITS "second" .1.3.6.1.4.1.2696.3.2.1.5.2.100.1.1.23 |
tsTestsPrefTxTTableIntervalMaxMaximum permitted TDT and TOT table repetition intervalsrw FloatingPoint UNITS "second" .1.3.6.1.4.1.2696.3.2.1.5.2.100.1.1.24 |
tsTestsPrefSDTActualIntervalMaxMaximum permitted SDT_actual section repetition intervalrw FloatingPoint UNITS "second" .1.3.6.1.4.1.2696.3.2.1.5.2.100.1.1.25 |
tsTestsPrefSDTActualIntervalMinMinimum permitted SDT_actual section repetition intervalrw FloatingPoint UNITS "second" .1.3.6.1.4.1.2696.3.2.1.5.2.100.1.1.26 |
tsTestsPrefSDTOtherIntervalMaxMaximum permitted SDT_other section repetition intervalrw FloatingPoint UNITS "second" .1.3.6.1.4.1.2696.3.2.1.5.2.100.1.1.27 |
tsTestsPrefEITActualIntervalMaxMaximum permitted EIT_actual section repetition interval (applies to both present and following sections).rw FloatingPoint UNITS "second" .1.3.6.1.4.1.2696.3.2.1.5.2.100.1.1.28 |
tsTestsPrefEITActualIntervalMinMinimum permitted EIT_actual section repetition intervalrw FloatingPoint UNITS "second" .1.3.6.1.4.1.2696.3.2.1.5.2.100.1.1.29 |
tsTestsPrefEITOtherIntervalMaxMaximum permitted EIT_other section repetition interval (applies to both present and following sections).rw FloatingPoint UNITS "second" .1.3.6.1.4.1.2696.3.2.1.5.2.100.1.1.30 |
tsTestsPrefRSTIntervalMinMinimum permitted RST section repetition intervalrw FloatingPoint UNITS "second" .1.3.6.1.4.1.2696.3.2.1.5.2.100.1.1.31 |
tsTestsPrefTDTIntervalMaxMaximum permitted TDT section repetition intervalrw FloatingPoint UNITS "second" .1.3.6.1.4.1.2696.3.2.1.5.2.100.1.1.32 |
tsTestsPrefTDTIntervalMinMinimum permitted TDT section repetition intervalrw FloatingPoint UNITS "second" .1.3.6.1.4.1.2696.3.2.1.5.2.100.1.1.33 |
tsTestsPreferencesPIDTableThis table contains measurement thresholds and other configuration information that is applied on a per PID per Transport Stream basis. SEQUENCE OF TsTestsPreferencesPIDEntry .1.3.6.1.4.1.2696.3.2.1.5.2.100.2 |
tsTestsPreferencesPIDEntryDescription. TsTestsPreferencesPIDEntry .1.3.6.1.4.1.2696.3.2.1.5.2.100.2.1 |
tsTestsPrefPIDInputNumberTransport Stream input to which the preferences apply InputNumber .1.3.6.1.4.1.2696.3.2.1.5.2.100.2.1.1 |
tsTestsPrefPIDPIDPID to which these preferences apply PIDPlusOne .1.3.6.1.4.1.2696.3.2.1.5.2.100.2.1.2 |
tsTestsPrefPIDRowStatusThis object is used to manage the rows in this table.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.2696.3.2.1.5.2.100.2.1.3 |
tsTestsPrefPIDReferredIntervalMaxMaximum permitted interval between the arrival of consecutive packets of this PID. The default value for this object is the current value of tsTestsPrefReferredIntervalMax for the same input.rw FloatingPoint UNITS "second" .1.3.6.1.4.1.2696.3.2.1.5.2.100.2.1.4 |
tsMeasurements OBJECT IDENTIFIER .1.3.6.1.4.1.2696.3.2.1.5.4 |
tsPcrMeasurementTableThis table makes available the PCR_FO, PCR_DR, PCR_OJ and PCR_AC measurements. SEQUENCE OF TsPcrMeasurementEntry .1.3.6.1.4.1.2696.3.2.1.5.4.1 |
tsPcrMeasurementEntryRow specification TsPcrMeasurementEntry .1.3.6.1.4.1.2696.3.2.1.5.4.1.1 |
tsPcrMeasurementInputNumberInput on which the measurement is made InputNumber .1.3.6.1.4.1.2696.3.2.1.5.4.1.1.1 |
tsPcrMeasurementPIDPID (plus one) in the Transport Stream carrying (or expected to carry) PCRs. PIDPlusOne .1.3.6.1.4.1.2696.3.2.1.5.4.1.1.2 |
tsPcrMeasurementNumberThis selects one of the four PCR measurements IndexPCRMeasurement .1.3.6.1.4.1.2696.3.2.1.5.4.1.1.3 |
tsPcrMeasurementRowStatusThis object is used by the manager to create and delete rows in the table. The agent automatically creates rows for PIDs where it detects the presence of a PCR.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.2696.3.2.1.5.4.1.1.4 |
tsPcrMeasurementStateThis gives the overall pass/fail state of the threshold test on this measurementro TestState .1.3.6.1.4.1.2696.3.2.1.5.4.1.1.5 |
tsPcrMeasurementEnableDetermines whether this test and associated traps are enabled.rw Enable .1.3.6.1.4.1.2696.3.2.1.5.4.1.1.6 |
tsPcrMeasurementCounterCount of the number of times a threshold error has occurred for this measurement.ro Counter32 .1.3.6.1.4.1.2696.3.2.1.5.4.1.1.7 |
tsPcrMeasurementCounterDiscontinuityProvides the last time at which there was a discontinuity in the tsPcrMeasurementCounter object.ro DateAndTime (SNMPv2-TC) .1.3.6.1.4.1.2696.3.2.1.5.4.1.1.8 |
tsPcrMeasurementCounterResettsPcrMeasurementCounter is reset to zero and tsPcrMeasurementCounterDiscontinuity is set to the current time if 'true' is written to this variable. When read, the value of this object is always 'false'.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.2696.3.2.1.5.4.1.1.9 |
tsPcrMeasurementLatestErrorThe timestamp at the most recent occurrence of a threshold error on this measurement.ro DateAndTime (SNMPv2-TC) .1.3.6.1.4.1.2696.3.2.1.5.4.1.1.10 |
tsPcrMeasurementActiveTimeThe total time when it has been possible to make this measurementro ActiveTime UNITS "second" .1.3.6.1.4.1.2696.3.2.1.5.4.1.1.11 |
tsPcrMeasurementMeasurementStateIndicates the validity of the measurementro MeasurementState .1.3.6.1.4.1.2696.3.2.1.5.4.1.1.12 |
tsPcrMeasurementValueThe units for the measured value depend on the measurement: PCR_FO Hz PCR_DR Hz/s Values for PCR_OJ and PCR_AC are not provided as they occur too quickly to be usefully retrieved via SNMP. For these measurements, the MeasurementState is always 'unknown'. However, the threshold tests are expected to work correctly for these measurements.ro FloatingPoint .1.3.6.1.4.1.2696.3.2.1.5.4.1.1.13 |
bitRate OBJECT IDENTIFIER .1.3.6.1.4.1.2696.3.2.1.5.4.2 |
tsTransportStreamBitRateTableBit rates for each complete Transport Stream SEQUENCE OF TsTransportStreamBitRateEntry .1.3.6.1.4.1.2696.3.2.1.5.4.2.1 |
tsTransportStreamBitRateEntryRow specification TsTransportStreamBitRateEntry .1.3.6.1.4.1.2696.3.2.1.5.4.2.1.1 |
tsTransportStreamBitRateInputNumberTransport Stream on which the measurement is made InputNumber .1.3.6.1.4.1.2696.3.2.1.5.4.2.1.1.1 |
tsTransportStreamBitRateStateThis gives the overall pass/fail state of the threshold test on this measurementro TestState .1.3.6.1.4.1.2696.3.2.1.5.4.2.1.1.2 |
tsTransportStreamBitRateEnableDetermines whether the threshold test and associated traps for this measurement are enabled.rw Enable .1.3.6.1.4.1.2696.3.2.1.5.4.2.1.1.3 |
tsTransportStreamBitRateCounterCount of the number of times a threshold error has occurred for this measurement.ro Counter32 .1.3.6.1.4.1.2696.3.2.1.5.4.2.1.1.4 |
tsTransportStreamBitRateCounterDiscontinuityProvides the last time at which there was a discontinuity in the tsTransportStreamBitRateCounterobject.ro DateAndTime (SNMPv2-TC) .1.3.6.1.4.1.2696.3.2.1.5.4.2.1.1.5 |
tsTransportStreamBitRateCounterResettsTransportStreamBitRateCounteris reset to zero and tsTransportStreamBitRateCounterDiscontinuity is set to the current time if 'true' is written to this variable. When read, the value of this object is always 'false'.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.2696.3.2.1.5.4.2.1.1.6 |
tsTransportStreamBitRateLatestErrorThe timestamp at the most recent occurrence of a threshold error on this measurement.ro DateAndTime (SNMPv2-TC) .1.3.6.1.4.1.2696.3.2.1.5.4.2.1.1.7 |
tsTransportStreamBitRateActiveTimeThe total time when it has been possible to perform this measurementro ActiveTime UNITS "second" .1.3.6.1.4.1.2696.3.2.1.5.4.2.1.1.8 |
tsTransportStreamBitRateMeasurementStateIndicates the validity of the measurementro MeasurementState .1.3.6.1.4.1.2696.3.2.1.5.4.2.1.1.9 |
tsTransportStreamBitRateValueThe overall Transport Stream bit ratero FloatingPoint UNITS "bit/s" .1.3.6.1.4.1.2696.3.2.1.5.4.2.1.1.10 |
tsTransportStreamBitRateNomenclatureStandardised description of the method of measurement of the bitrate, for example 'bit/s @MGB2'ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.2696.3.2.1.5.4.2.1.1.11 |
tsServiceBitRateTableBit rates for each service/program within each Transport Stream. The table is sparse, in that only services mentioned in the PMT will be present. The bit rate of a service is the sum of the bit rates of the elementary_PID's in its PMT and the CA_PID's in any CA_descriptors in its PMT (ECMs). The bit rate of the PMT itself is excluded. The bit rate of the PCR_PID is excluded unless the PCR_PID is also one of the elementary_PID's in the PMT. SEQUENCE OF TsServiceBitRateEntry .1.3.6.1.4.1.2696.3.2.1.5.4.2.2 |
tsServiceBitRateEntryRow specification TsServiceBitRateEntry .1.3.6.1.4.1.2696.3.2.1.5.4.2.2.1 |
tsServiceBitRateInputNumberTransport Stream on which the measurement is made InputNumber .1.3.6.1.4.1.2696.3.2.1.5.4.2.2.1.1 |
tsServiceBitRateServiceThe program_number/service_id to which the information in the rest of the row applies. ServiceId .1.3.6.1.4.1.2696.3.2.1.5.4.2.2.1.2 |
tsServiceBitRateRowStatusThis is used by the manager to create and delete rows in the table. The agent will automatically create rows for services it finds in the PMT.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.2696.3.2.1.5.4.2.2.1.3 |
tsServiceBitRateStateThis gives the overall pass/fail state of the threshold test on this measurementro TestState .1.3.6.1.4.1.2696.3.2.1.5.4.2.2.1.4 |
tsServiceBitRateEnableDetermines whether the threshold test and associated traps for this measurement are enabled.rw Enable .1.3.6.1.4.1.2696.3.2.1.5.4.2.2.1.5 |
tsServiceBitRateCounterCount of the number of times a threshold error has occurred for this measurement.ro Counter32 .1.3.6.1.4.1.2696.3.2.1.5.4.2.2.1.6 |
tsServiceBitRateCounterDiscontinuityProvides the last time at which there was a discontinuity in the tsServiceBitRateCounter object.ro DateAndTime (SNMPv2-TC) .1.3.6.1.4.1.2696.3.2.1.5.4.2.2.1.7 |
tsServiceBitRateCounterResettsServiceBitRateCounter is reset to zero and tsServiceBitRateCounterDiscontinuity is set to the current time if 'true' is written to this variable. When read, the value of this object is always 'false'.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.2696.3.2.1.5.4.2.2.1.8 |
tsServiceBitRateLatestErrorThe timestamp at the most recent occurrence of a threshold error on this measurement.ro DateAndTime (SNMPv2-TC) .1.3.6.1.4.1.2696.3.2.1.5.4.2.2.1.9 |
tsServiceBitRateActiveTimeThe total time when it has been possible to perform this measurementro ActiveTime UNITS "second" .1.3.6.1.4.1.2696.3.2.1.5.4.2.2.1.10 |
tsServiceBitRateMeasurementStateIndicates the validity of the measurementro MeasurementState .1.3.6.1.4.1.2696.3.2.1.5.4.2.2.1.11 |
tsServiceBitRateValueOverall bit rate for the servicero FloatingPoint UNITS "bit/s" .1.3.6.1.4.1.2696.3.2.1.5.4.2.2.1.12 |
tsServiceBitRateNomenclatureStandardised description of the method of measurement of the bitrate, for example 'bit/s @MGB2'ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.2696.3.2.1.5.4.2.2.1.13 |
tsPIDBitRateTableBit rates for each PID within each Transport Stream. The table is sparse, in that only PIDs whose bit rate is currently greater than zero will be present in the table. This allows for faster traversal of the table to build up a list of PID bit rates. SEQUENCE OF TsPIDBitRateEntry .1.3.6.1.4.1.2696.3.2.1.5.4.2.3 |
tsPIDBitRateEntryRow specification TsPIDBitRateEntry .1.3.6.1.4.1.2696.3.2.1.5.4.2.3.1 |
tsPIDBitRateInputNumberTransport Stream on which the measurement is made InputNumber .1.3.6.1.4.1.2696.3.2.1.5.4.2.3.1.1 |
tsPIDBitRatePIDPID whose bit rate is being measured (plus one) PIDPlusOne .1.3.6.1.4.1.2696.3.2.1.5.4.2.3.1.2 |
tsPIDBitRateRowStatusThis is used by the manager to create and delete rows in the table. The agent will automatically create rows for PIDs whose bit rate is non-zero.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.2696.3.2.1.5.4.2.3.1.3 |
tsPIDBitRateStateThis gives the overall pass/fail state of the threshold test on this measurementro TestState .1.3.6.1.4.1.2696.3.2.1.5.4.2.3.1.4 |
tsPIDBitRateEnableDetermines whether the threshold test and associated traps for this measurement are enabled.rw Enable .1.3.6.1.4.1.2696.3.2.1.5.4.2.3.1.5 |
tsPIDBitRateCounterCount of the number of times a threshold error has occurred for this measurement.ro Counter32 .1.3.6.1.4.1.2696.3.2.1.5.4.2.3.1.6 |
tsPIDBitRateCounterDiscontinuityProvides the last time at which there was a discontinuity in the tsPIDBitRateCounter object.ro DateAndTime (SNMPv2-TC) .1.3.6.1.4.1.2696.3.2.1.5.4.2.3.1.7 |
tsPIDBitRateCounterResettsPIDBitRateCounter is reset to zero and tsPIDBitRateCounterDiscontinuity is set to the current time if 'true' is written to this variable. When read, the value of this object is always 'false'.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.2696.3.2.1.5.4.2.3.1.8 |
tsPIDBitRateLatestErrorThe timestamp at the most recent occurrence of a threshold error on this measurement.ro DateAndTime (SNMPv2-TC) .1.3.6.1.4.1.2696.3.2.1.5.4.2.3.1.9 |
tsPIDBitRateActiveTimeThe total time when it has been possible to perform this measurementro ActiveTime UNITS "second" .1.3.6.1.4.1.2696.3.2.1.5.4.2.3.1.10 |
tsPIDBitRateMeasurementStateIndicates the validity of the measurementro MeasurementState .1.3.6.1.4.1.2696.3.2.1.5.4.2.3.1.11 |
tsPIDBitRateValueBit rate for the PID.ro FloatingPoint UNITS "bit/s" .1.3.6.1.4.1.2696.3.2.1.5.4.2.3.1.12 |
tsPIDBitRateNomenclatureStandardised description of the method of measurement of the bitrate, for example 'bit/s @MGB2'ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.2696.3.2.1.5.4.2.3.1.13 |
tsConsistencyTableThis table provides the result of the Transport Stream consistency test for each input. SEQUENCE OF TsConsistencyEntry .1.3.6.1.4.1.2696.3.2.1.5.4.3 |
tsConsistencyEntryRow specification TsConsistencyEntry .1.3.6.1.4.1.2696.3.2.1.5.4.3.1 |
tsConsistencyInputNumberInput (Transport Stream) on which the consistency check is made. InputNumber .1.3.6.1.4.1.2696.3.2.1.5.4.3.1.1 |
tsConsistencyTestNumberSpecifies the consistency check test IndexConsistencyTest .1.3.6.1.4.1.2696.3.2.1.5.4.3.1.2 |
tsConsistencyStateThis gives the overall pass/fail state of the consistency check.ro TestState .1.3.6.1.4.1.2696.3.2.1.5.4.3.1.3 |
tsConsistencyEnableDetermines whether this test and associated traps are enabled.rw Enable .1.3.6.1.4.1.2696.3.2.1.5.4.3.1.4 |
tsConsistencyCounterCount of the number of times the consistency check has failed.ro Counter32 .1.3.6.1.4.1.2696.3.2.1.5.4.3.1.5 |
tsConsistencyCounterDiscontinuityProvides the last time at which there was a discontinuity in the tsConsistencyCounter object.ro DateAndTime (SNMPv2-TC) .1.3.6.1.4.1.2696.3.2.1.5.4.3.1.6 |
tsConsistencyCounterResettsConsistencyCounter is reset to zero and tsConsistencyCounterDiscontinuity is set to the current time if 'true' is written to this variable. When read, the value of this object is always 'false'.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.2696.3.2.1.5.4.3.1.7 |
tsConsistencyLatestErrorThe timestamp at the most recent failure of the consistency check.ro DateAndTime (SNMPv2-TC) .1.3.6.1.4.1.2696.3.2.1.5.4.3.1.8 |
tsConsistencyActiveTimeThe total time when it has been possible to perform this testro ActiveTime UNITS "second" .1.3.6.1.4.1.2696.3.2.1.5.4.3.1.9 |
tsMeasurePreferences OBJECT IDENTIFIER .1.3.6.1.4.1.2696.3.2.1.5.4.100 |
tsMeasurePreferencesTableThis table contains configuration information for the tsMeasurements branch of the MIB. Configuration related to the whole Transport Stream is found here. SEQUENCE OF TsMeasurePreferencesEntry .1.3.6.1.4.1.2696.3.2.1.5.4.100.1 |
tsMeasurePreferencesEntryRow specification TsMeasurePreferencesEntry .1.3.6.1.4.1.2696.3.2.1.5.4.100.1.1 |
tsMeasurePrefInputNumberTransport Stream input to which the preferences apply InputNumber .1.3.6.1.4.1.2696.3.2.1.5.4.100.1.1.1 |
tsMeasurePrefPCRDemarcationFrequencyThis is the demarcation frequency used by the PCR measurement system to distinguish between inaccuracy/jitter and drift.rw FloatingPoint .1.3.6.1.4.1.2696.3.2.1.5.4.100.1.1.2 |
tsMeasurePrefPCRFOMaxMaximum permitted PCR_FO (frequency offset). An error is indicated if the measured PCR_FO is outside the range [-tsMeasurePrefPCRFOMax .. +tsMeasurePrefPCRFOMax].rw FloatingPoint UNITS "Hz" .1.3.6.1.4.1.2696.3.2.1.5.4.100.1.1.3 |
tsMeasurePrefPCRDRMaxMaximum permitted PCR_DR (drift rate). An error is indicated if the measured PCR_DR is outside the range [-tsMeasurePrefPCRDRMax .. +tsMeasurePrefPCRDRMax]rw FloatingPoint UNITS "Hz/s" .1.3.6.1.4.1.2696.3.2.1.5.4.100.1.1.4 |
tsMeasurePrefPCROJMaxMaximum permitted PCR_OJ (overall jitter). An error is indicated if the measured PCR_OJ is outside the range [-tsMeasurePrefPCROJMax .. +tsMeasurePrefPCROJMax]rw FloatingPoint UNITS "second" .1.3.6.1.4.1.2696.3.2.1.5.4.100.1.1.5 |
tsMeasurePrefTSBitRateTau'tau' value for Transport Stream bit rate measurement. The MIB provides very flexible ways of setting the bit rate measurement parameters tau, N and element for the Transport Stream, services, PIDs and for individual services and PIDs. Real measurement equipment can be expected to provide much less flexibility. Management software should anticipate this by either being statically aware of the capabilities of the agent or by checking that preference settings have been accepted by reading them back after each attempt to set them.rw FloatingPoint UNITS "second" .1.3.6.1.4.1.2696.3.2.1.5.4.100.1.1.6 |
tsMeasurePrefTSBitRateN'N' value for Transport Stream bit rate measurement. See note in description for tsMeasurePrefTSBitRateTau.rw Unsigned32 .1.3.6.1.4.1.2696.3.2.1.5.4.100.1.1.7 |
tsMeasurePrefTSBitRateElementData unit which is counted by the bit rate measurement algorithm. See note in description for tsMeasurePrefTSBitRateTau.rw BitRateElement .1.3.6.1.4.1.2696.3.2.1.5.4.100.1.1.8 |
tsMeasurePrefTSBitRateMinAn error is generated if the Transport Stream bit rate is below this value.rw FloatingPoint UNITS "bit/s" .1.3.6.1.4.1.2696.3.2.1.5.4.100.1.1.9 |
tsMeasurePrefTSBitRateMaxAn error is generated if the Transport Stream bit rate exceeds this value.rw FloatingPoint UNITS "bit/s" .1.3.6.1.4.1.2696.3.2.1.5.4.100.1.1.10 |
tsMeasurePrefAllServiceBitRateTau'tau' value for Service bit rate measurement. When a manager sets the value of this object, the values of the tsMeasurePrefServiceBitRateTau columns in all the rows of the tsMeasurePreferencesServiceTable are set to this same value. This also becomes the default value for any new rows created subsequently. See note in description for tsMeasurePrefTSBitRateTau.rw FloatingPoint UNITS "second" .1.3.6.1.4.1.2696.3.2.1.5.4.100.1.1.11 |
tsMeasurePrefAllServiceBitRateN'N' value for Service bit rate measurement. When a manager sets the value of this object, the values of the tsMeasurePrefServiceBitRateN columns in all the rows of the tsMeasurePreferencesServiceTable are set to this same value. This also becomes the default value for any new rows created subsequently. See note in description for tsMeasurePrefTSBitRateTau.rw Unsigned32 .1.3.6.1.4.1.2696.3.2.1.5.4.100.1.1.12 |
tsMeasurePrefAllServiceBitRateElementData unit which is counted by the bit rate measurement algorithm for services. When a manager sets the value of this object, the values of the tsMeasurePrefServiceBitRateElement columns in all the rows of the tsMeasurePreferencesServiceTable are set to this same value. This also becomes the default value for any new rows created subsequently. See note in description for tsMeasurePrefTSBitRateTau.rw BitRateElement .1.3.6.1.4.1.2696.3.2.1.5.4.100.1.1.13 |
tsMeasurePrefAllPIDBitRateTau'tau' value for Service bit rate measurement. When a manager sets the value of this object, the values of the tsMeasurePrefPIDBitRateTau columns in all the rows of the tsMeasurePreferencesPIDTable are set to this same value. This also becomes the default value for any new rows created subsequently. See note in description for tsMeasurePrefTSBitRateTau.rw FloatingPoint UNITS "second" .1.3.6.1.4.1.2696.3.2.1.5.4.100.1.1.14 |
tsMeasurePrefAllPIDBitRateN'N' value for PID bit rate measurement. When a manager sets the value of this object, the values of the tsMeasurePrefPIDBitRateN columns in all the rows of the tsMeasurePreferencesPIDTable are set to this same value. This also becomes the default value for any new rows created subsequently. See note in description for tsMeasurePrefTSBitRateTau.rw Unsigned32 .1.3.6.1.4.1.2696.3.2.1.5.4.100.1.1.15 |
tsMeasurePrefAllPIDBitRateElementData unit which is counted by the bit rate measurement algorithm for PIDs. When a manager sets the value of this object, the values of the tsMeasurePrefPIDBitRateElement columns in all the rows of the tsMeasurePreferencesPIDTable are set to this same value. This also becomes the default value for any new rows created subsequently. See note in description for tsMeasurePrefTSBitRateTau.rw BitRateElement .1.3.6.1.4.1.2696.3.2.1.5.4.100.1.1.16 |
tsMeasurePrefExpectedTSIDThis object defines the expected Transport Stream ID that is compared with the actual ID to perform the consistency of information check.rw TransportStreamID .1.3.6.1.4.1.2696.3.2.1.5.4.100.1.1.17 |
tsMeasurePreferencesServiceTableThis table contains configuration information for the tsMeasurements branch of the MIB. Configuration related to individual services is found here. SEQUENCE OF TsMeasurePreferencesServiceEntry .1.3.6.1.4.1.2696.3.2.1.5.4.100.2 |
tsMeasurePreferencesServiceEntryRow specification TsMeasurePreferencesServiceEntry .1.3.6.1.4.1.2696.3.2.1.5.4.100.2.1 |
tsMeasurePrefServiceInputNumberTransport Stream input to which the preferences apply InputNumber .1.3.6.1.4.1.2696.3.2.1.5.4.100.2.1.1 |
tsMeasurePrefServiceServiceService to which the preferences apply. ServiceId .1.3.6.1.4.1.2696.3.2.1.5.4.100.2.1.2 |
tsMeasurePrefServiceRowStatusThis is used by the manager to create and delete rows in the table. The agent will automatically create rows for services it finds in the PMT.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.2696.3.2.1.5.4.100.2.1.3 |
tsMeasurePrefServiceBitRateTau'tau' value for bit rate measurement for this service. See note in description for tsMeasurePrefTSBitRateTau. If an agent does not support per service tau settings, it shall ignore attempts to change the setting by writing to this object.rw FloatingPoint UNITS "second" .1.3.6.1.4.1.2696.3.2.1.5.4.100.2.1.4 |
tsMeasurePrefServiceBitRateN'N' value for rate measurement for this service. See note in description for tsMeasurePrefTSBitRateTau. If an agent does not support per service 'N' settings, it shall ignore attempts to change the setting by writing to this object.rw Unsigned32 .1.3.6.1.4.1.2696.3.2.1.5.4.100.2.1.5 |
tsMeasurePrefServiceBitRateElementData unit which is counted by the bit rate measurement algorithm for this service. See note in description for tsMeasurePrefTSBitRateTau. If an agent does not support per service element settings, it shall ignore attempts to change the setting by writing to this object.rw BitRateElement .1.3.6.1.4.1.2696.3.2.1.5.4.100.2.1.6 |
tsMeasurePrefServiceBitRateMinAn error is generated if the Service bit rate is below this value.rw FloatingPoint UNITS "bit/s" .1.3.6.1.4.1.2696.3.2.1.5.4.100.2.1.7 |
tsMeasurePrefServiceBitRateMaxAn error is generated if the Transport Stream bit rate exceeds this value.rw FloatingPoint UNITS "bit/s" .1.3.6.1.4.1.2696.3.2.1.5.4.100.2.1.8 |
tsMeasurePreferencesPIDTableThis table contains configuration information for the tsMeasurements branch of the MIB. Configuration related to individual PIDs is found here. SEQUENCE OF TsMeasurePreferencesPIDEntry .1.3.6.1.4.1.2696.3.2.1.5.4.100.3 |
tsMeasurePreferencesPIDEntryRow specification TsMeasurePreferencesPIDEntry .1.3.6.1.4.1.2696.3.2.1.5.4.100.3.1 |
tsMeasurePrefPIDInputNumberTransport Stream input to which the preferences apply InputNumber .1.3.6.1.4.1.2696.3.2.1.5.4.100.3.1.1 |
tsMeasurePrefPIDPIDPID (plus one) to which the preferences apply. PIDPlusOne .1.3.6.1.4.1.2696.3.2.1.5.4.100.3.1.2 |
tsMeasurePrefPIDRowStatusThis is used by the manager to create and delete rows in the table. The agent will automatically create rows for PIDs which have a non-zero bit rate.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.2696.3.2.1.5.4.100.3.1.3 |
tsMeasurePrefPIDBitRateTau'tau' value for bit rate measurement for this PID. See note in description for tsMeasurePrefTSBitRateTau. If an agent does not support per PID tau settings, it shall ignore attempts to change the setting by writing to this object.rw FloatingPoint UNITS "second" .1.3.6.1.4.1.2696.3.2.1.5.4.100.3.1.4 |
tsMeasurePrefPIDBitRateN'N' value for bit rate measurement for this PID. See note in description for tsMeasurePrefTSBitRateTau. If an agent does not support per PID 'N' settings, it shall ignore attempts to change the setting by writing to this object.rw Unsigned32 .1.3.6.1.4.1.2696.3.2.1.5.4.100.3.1.5 |
tsMeasurePrefPIDBitRateElementData unit which is counted by the bit rate measurement algorithm for this PID. See note in description for tsMeasurePrefTSBitRateTau. If an agent does not support per PID element settings, it shall ignore attempts to change the setting by writing to this object.rw BitRateElement .1.3.6.1.4.1.2696.3.2.1.5.4.100.3.1.6 |
tsMeasurePrefPIDBitRateMinAn error is generated if the PID bit rate is below this value.rw FloatingPoint UNITS "bit/s" .1.3.6.1.4.1.2696.3.2.1.5.4.100.3.1.7 |
tsMeasurePrefPIDBitRateMaxAn error is generated if the PID bit rate exceeds this value.rw FloatingPoint UNITS "bit/s" .1.3.6.1.4.1.2696.3.2.1.5.4.100.3.1.8 |
tsServicePerformance OBJECT IDENTIFIER .1.3.6.1.4.1.2696.3.2.1.5.5 |
tsServicePerformanceTableThis table gives access to the Service Performance measurements and tests SEQUENCE OF TsServicePerformanceEntry .1.3.6.1.4.1.2696.3.2.1.5.5.2 |
tsServicePerformanceEntryRow specification TsServicePerformanceEntry .1.3.6.1.4.1.2696.3.2.1.5.5.2.1 |
tsServicePerformanceInputNumberTransport Stream on which the measurement is made InputNumber .1.3.6.1.4.1.2696.3.2.1.5.5.2.1.1 |
tsServicePerformanceNumberThe Service Performance measurement which this row applies to. IndexServicePerformance .1.3.6.1.4.1.2696.3.2.1.5.5.2.1.2 |
tsServicePerformanceStateThis gives the overall pass/fail state of the threshold test on this measurement. The threshold test fails if the value of tsServicePerformanceErrorRatio exceeds the value given in the preferences.ro TestState .1.3.6.1.4.1.2696.3.2.1.5.5.2.1.3 |
tsServicePerformanceEnableDetermines whether the threshold test and associated traps for this measurement are enabled.rw Enable .1.3.6.1.4.1.2696.3.2.1.5.5.2.1.4 |
tsServicePerformanceCounterCount of the number of times a threshold error has occurred for this measurement.ro Counter32 .1.3.6.1.4.1.2696.3.2.1.5.5.2.1.5 |
tsServicePerformanceCounterDiscontinuityProvides the last time at which there was a discontinuity in the tsServicePerformanceCounter object.ro DateAndTime (SNMPv2-TC) .1.3.6.1.4.1.2696.3.2.1.5.5.2.1.6 |
tsServicePerformanceCounterResettsServicePerformanceCounter is reset to zero and tsServicePerformanceCounterDiscontinuity is set to the current time if 'true' is written to this variable. The value read from this object is always 'false'.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.2696.3.2.1.5.5.2.1.7 |
tsServicePerformanceLatestErrorThe timestamp at the most recent occurrence of a threshold error on this measurement.ro DateAndTime (SNMPv2-TC) .1.3.6.1.4.1.2696.3.2.1.5.5.2.1.8 |
tsServicePerformanceActiveTimeThe total time when it has been possible to perform this measurementro ActiveTime UNITS "second" .1.3.6.1.4.1.2696.3.2.1.5.5.2.1.9 |
tsServicePerformanceMeasurementStateIndicates the validity of the measurementro MeasurementState .1.3.6.1.4.1.2696.3.2.1.5.5.2.1.10 |
tsServicePerformanceErrorThe calculated xxx_Error parameter as measured at the end of the most recently completed DeltaT period.ro Unsigned32 .1.3.6.1.4.1.2696.3.2.1.5.5.2.1.11 |
tsServicePerformanceErrorRatioThis is the calculated xxx_Error_Ratio as a percentage (e.g. '1.32'). The value is for the most recently completed evaluation time (e.g. 10 minutes).ro FloatingPoint .1.3.6.1.4.1.2696.3.2.1.5.5.2.1.12 |
tsServicePerformancePreferencesTableParameters controlling the Service Performance measurements SEQUENCE OF TsServicePerformancePreferencesEntry .1.3.6.1.4.1.2696.3.2.1.5.5.100 |
tsServicePerformancePreferencesEntryRow specification TsServicePerformancePreferencesEntry .1.3.6.1.4.1.2696.3.2.1.5.5.100.1 |
tsSPPrefInputNumberTransport Stream input to which the preferences apply InputNumber .1.3.6.1.4.1.2696.3.2.1.5.5.100.1.1 |
tsSPPrefNumberThe service performance parameter to which these preferences apply. IndexServicePerformance .1.3.6.1.4.1.2696.3.2.1.5.5.100.1.2 |
tsSPPrefDeltaTThe defined time interval over which errors are countedrw FloatingPoint UNITS "second" .1.3.6.1.4.1.2696.3.2.1.5.5.100.1.3 |
tsSPPrefEvaluationTimeThe period over which the ...Error_Ratio is calculatedrw FloatingPoint UNITS "second" .1.3.6.1.4.1.2696.3.2.1.5.5.100.1.4 |
tsSPPrefThresholdThe threshold value used in calculating the ..._Error_Ratio.rw FloatingPoint .1.3.6.1.4.1.2696.3.2.1.5.5.100.1.5 |
tr101290CableSat OBJECT IDENTIFIER .1.3.6.1.4.1.2696.3.2.1.6 |
sysAvailabilityTableSystem availability measurement SEQUENCE OF SysAvailabilityEntry .1.3.6.1.4.1.2696.3.2.1.6.1 |
sysAvailabilityEntryRow specification SysAvailabilityEntry .1.3.6.1.4.1.2696.3.2.1.6.1.1 |
sysAvailabilityInputNumberTransport Stream on which the measurement is made InputNumber .1.3.6.1.4.1.2696.3.2.1.6.1.1.1 |
sysAvailabilityTestStateA 'fail' is an approximate indication that the system is in a period of unavailable time (UAT). 'fail' is indicated as soon as a trigger period for unavailable time completes. 'pass' is indicated as soon as a trigger period for available time completes. This necessarily differs from the strict definition of UAT because the measuring equipment is unable to look into the future.ro TestState .1.3.6.1.4.1.2696.3.2.1.6.1.1.2 |
sysAvailabilityEnableDetermines whether system availability testing is performed and whether the associated traps are generated.rw Enable .1.3.6.1.4.1.2696.3.2.1.6.1.1.3 |
sysAvailabilityCounterCount of the number of times the system has become unavailablero Counter32 .1.3.6.1.4.1.2696.3.2.1.6.1.1.4 |
sysAvailabilityCounterDiscontinuityProvides the last time at which there was a discontinuity in the sysAvailabilityCounter object.ro DateAndTime (SNMPv2-TC) .1.3.6.1.4.1.2696.3.2.1.6.1.1.5 |
sysAvailabilityCounterResetsysAvailabilityCounter is reset to zero and sysAvailabilityCounterDiscontinuity is set to the current time if 'true' is written to this variable. When read, the value of this object is always 'false'.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.2696.3.2.1.6.1.1.6 |
sysAvailabilityLatestErrorThe timestamp when the system most recently became unavailable.ro DateAndTime (SNMPv2-TC) .1.3.6.1.4.1.2696.3.2.1.6.1.1.7 |
sysAvailabilityActiveTimeThis is a monotonically increasing value in units of seconds that represents the total amount of time for which the instrument has been able to perform the test/measurement. It can be used to calculate the Total Time in the calculation of the availability.ro ActiveTime UNITS "second" .1.3.6.1.4.1.2696.3.2.1.6.1.1.8 |
sysAvailabilityMeasurementStateIndicates the validity of the measurementro MeasurementState .1.3.6.1.4.1.2696.3.2.1.6.1.1.9 |
sysAvailabilityUnavailableTimeThis is a monotonically increasing time in seconds which measures the total Unavailable Time (UAT) since the measuring system was last restarted.ro Unsigned32 UNITS "second" .1.3.6.1.4.1.2696.3.2.1.6.1.1.10 |
sysAvailabilityRatioThis is the System Availability ratio as a percentage (e.g. 99.643) measured over the previous 'Total Time' measurement period.ro FloatingPoint .1.3.6.1.4.1.2696.3.2.1.6.1.1.11 |
sysAvailabilityInSETIThis object has the value 'true' if and only if the most recently completed Time Interval (TI) was a Severely Errored Time Interval (SETI).ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.2696.3.2.1.6.1.1.12 |
linkAvailabilityTableLink availability measurement SEQUENCE OF LinkAvailabilityEntry .1.3.6.1.4.1.2696.3.2.1.6.2 |
linkAvailabilityEntryRow specification LinkAvailabilityEntry .1.3.6.1.4.1.2696.3.2.1.6.2.1 |
linkAvailabilityInputNumberTransport Stream on which the measurement is made InputNumber .1.3.6.1.4.1.2696.3.2.1.6.2.1.1 |
linkAvailabilityTestStateA 'fail' is an approximate indication that the system is in a period of link unavailable time (LUAT). 'fail' is indicated as soon as a trigger period for link unavailable time completes. 'pass' is indicated as soon as a trigger period for link available time completes. This necessarily differs from the strict definition of LUAT because the measuring equipment is unable to look into the future.ro TestState .1.3.6.1.4.1.2696.3.2.1.6.2.1.2 |
linkAvailabilityEnableDetermines whether link availability testing is performed and whether the associated traps are generated.rw Enable .1.3.6.1.4.1.2696.3.2.1.6.2.1.3 |
linkAvailabilityCounterCount of the number of times the link has become unavailable.ro Counter32 .1.3.6.1.4.1.2696.3.2.1.6.2.1.4 |
linkAvailabilityCounterDiscontinuityProvides the last time at which there was a discontinuity in the linkAvailabilityCounter object.ro DateAndTime (SNMPv2-TC) .1.3.6.1.4.1.2696.3.2.1.6.2.1.5 |
linkAvailabilityCounterResetlinkAvailabilityCounter is reset to zero and linkAvailabilityCounterDiscontinuity is set to the current time if 'true' is written to this variable. When read, the value of this object is always 'false'.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.2696.3.2.1.6.2.1.6 |
linkAvailabilityLatestErrorThe timestamp when the link most recently became unavailable.ro DateAndTime (SNMPv2-TC) .1.3.6.1.4.1.2696.3.2.1.6.2.1.7 |
linkAvailabilityActiveTimeThis is a monotonically increasing value in units of seconds that represents the total amount of time for which the instrument has been able to perform the measurement. It can be used to calculate the Total Time in the calculation of the availability.ro ActiveTime UNITS "second" .1.3.6.1.4.1.2696.3.2.1.6.2.1.8 |
linkAvailabilityMeasurementStateIndicates the validity of the measurementro MeasurementState .1.3.6.1.4.1.2696.3.2.1.6.2.1.9 |
linkAvailabilityUnavailableTimeThis is a monotonically increasing time in seconds which measures the total link unavailable time (LUAT) since the measuring system was last restarted.ro Unsigned32 UNITS "second" .1.3.6.1.4.1.2696.3.2.1.6.2.1.10 |
linkAvailabilityRatioThis is the Link Availability ratio as a percentage (e.g. 99.643) measured over the previous 'Total Time' measurement period.ro FloatingPoint .1.3.6.1.4.1.2696.3.2.1.6.2.1.11 |
linkAvailabilityInSUTIThis object has the value 'true' if and only if the most recently completed Time Interval (TI) was a Severely Uncorrectable Time Interval (SETI).ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.2696.3.2.1.6.2.1.12 |
berRSinServiceTableMeasurement of BER before RS decoder SEQUENCE OF BerRSinServiceEntry .1.3.6.1.4.1.2696.3.2.1.6.3 |
berRSinServiceEntryRow specification BerRSinServiceEntry .1.3.6.1.4.1.2696.3.2.1.6.3.1 |
berRSinServiceInputNumberTransport Stream on which the measurement is made InputNumber .1.3.6.1.4.1.2696.3.2.1.6.3.1.1 |
berRSinServiceTestStateThis indicates whether the berRSinServiceValue is below the maximum.ro TestState .1.3.6.1.4.1.2696.3.2.1.6.3.1.2 |
berRSinServiceEnableDetermines whether the threshold test and associated traps for this measurement are enabled.rw Enable .1.3.6.1.4.1.2696.3.2.1.6.3.1.3 |
berRSinServiceCounterCount of the number of times a threshold error has occurred for this measurement.ro Counter32 .1.3.6.1.4.1.2696.3.2.1.6.3.1.4 |
berRSinServiceCounterDiscontinuityProvides the last time at which there was a discontinuity in the berRSinServiceCounter object.ro DateAndTime (SNMPv2-TC) .1.3.6.1.4.1.2696.3.2.1.6.3.1.5 |
berRSinServiceCounterResetberRSinServiceCounter is reset to zero and berRSinServiceCounterDiscontinuity is set to the current time if 'true' is written to this object. When read, the value of this object is always 'false'.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.2696.3.2.1.6.3.1.6 |
berRSinServiceLatestErrorThe timestamp at the most recent occurrence of a threshold error on this measurement.ro DateAndTime (SNMPv2-TC) .1.3.6.1.4.1.2696.3.2.1.6.3.1.7 |
berRSinServiceActiveTimeThe total time when it has been possible to perform this measurementro ActiveTime UNITS "second" .1.3.6.1.4.1.2696.3.2.1.6.3.1.8 |
berRSinServiceMeasurementStateIndicates the validity of the measurementro MeasurementState .1.3.6.1.4.1.2696.3.2.1.6.3.1.9 |
berRSinServiceValueThis is the current BER as a numeric value, for example 0.0000023ro FloatingPoint .1.3.6.1.4.1.2696.3.2.1.6.3.1.10 |
rfIFsignalPowerTableRF or IF signal power measurement SEQUENCE OF RfIFsignalPowerEntry .1.3.6.1.4.1.2696.3.2.1.6.6 |
rfIFsignalPowerEntryRow specification RfIFsignalPowerEntry .1.3.6.1.4.1.2696.3.2.1.6.6.1 |
rfIFsignalPowerInputNumberTransport Stream on which the measurement is made InputNumber .1.3.6.1.4.1.2696.3.2.1.6.6.1.1 |
rfIFsignalPowerTestStateThis indicates whether the rfIFsignalPowerValue is currently within the thresholds.ro TestState .1.3.6.1.4.1.2696.3.2.1.6.6.1.2 |
rfIFsignalPowerEnableDetermines whether the threshold test and associated traps for this measurement are enabled.rw Enable .1.3.6.1.4.1.2696.3.2.1.6.6.1.3 |
rfIFsignalPowerCounterCount of the number of times a threshold error has occurred for this measurement.ro Counter32 .1.3.6.1.4.1.2696.3.2.1.6.6.1.4 |
rfIFsignalPowerCounterDiscontinuityProvides the last time at which there was a discontinuity in the rfIFsignalPowerCounter object.ro DateAndTime (SNMPv2-TC) .1.3.6.1.4.1.2696.3.2.1.6.6.1.5 |
rfIFsignalPowerCounterResetrfIFsignalPowerCounter is reset to zero and rfIFsignalPowerCounterDiscontinuity is set to the current time if 'true' is written to this object. When read, the value of this object is always 'false'.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.2696.3.2.1.6.6.1.6 |
rfIFsignalPowerLatestErrorThe timestamp at the most recent occurrence of a threshold error on this measurement.ro DateAndTime (SNMPv2-TC) .1.3.6.1.4.1.2696.3.2.1.6.6.1.7 |
rfIFsignalPowerActiveTimeThe total time when it has been possible to perform this measurementro ActiveTime UNITS "second" .1.3.6.1.4.1.2696.3.2.1.6.6.1.8 |
rfIFsignalPowerMeasurementStateIndicates the validity of the measurementro MeasurementState .1.3.6.1.4.1.2696.3.2.1.6.6.1.9 |
rfIFsignalPowerValueThe current RF power expressed in dBm, which references 0 dBm as the power of 1 mW.ro FloatingPoint UNITS "dBm" .1.3.6.1.4.1.2696.3.2.1.6.6.1.10 |
noisePowerTableNoise power measurement SEQUENCE OF NoisePowerEntry .1.3.6.1.4.1.2696.3.2.1.6.7 |
noisePowerEntryRow specification NoisePowerEntry .1.3.6.1.4.1.2696.3.2.1.6.7.1 |
noisePowerInputNumberTransport Stream on which the measurement is made InputNumber .1.3.6.1.4.1.2696.3.2.1.6.7.1.1 |
noisePowerTestStateThis indicates whether the noisePowerValue is currently below the maximum limit.ro TestState .1.3.6.1.4.1.2696.3.2.1.6.7.1.2 |
noisePowerEnableDetermines whether the threshold test and associated traps for this measurement are enabled.rw Enable .1.3.6.1.4.1.2696.3.2.1.6.7.1.3 |
noisePowerCounterCount of the number of times a threshold error has occurred for this measurement.ro Counter32 .1.3.6.1.4.1.2696.3.2.1.6.7.1.4 |
noisePowerCounterDiscontinuityProvides the last time at which there was a discontinuity in the noisePowerCounter object.ro DateAndTime (SNMPv2-TC) .1.3.6.1.4.1.2696.3.2.1.6.7.1.5 |
noisePowerCounterResetnoisePowerCounter is reset to zero and noisePowerCounterDiscontinuity is set to the current time if 'true' is written to this object. When read, the value of this object is always 'false'.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.2696.3.2.1.6.7.1.6 |
noisePowerLatestErrorThe timestamp at the most recent occurrence of a threshold error on this measurement.ro DateAndTime (SNMPv2-TC) .1.3.6.1.4.1.2696.3.2.1.6.7.1.7 |
noisePowerActiveTimeThe total time when it has been possible to perform this measurementro ActiveTime UNITS "second" .1.3.6.1.4.1.2696.3.2.1.6.7.1.8 |
noisePowerMeasurementStateIndicates the validity of the measurementro MeasurementState .1.3.6.1.4.1.2696.3.2.1.6.7.1.9 |
noisePowerValueThe current RF noise power expressed in dBm, which references 0 dBm as the power of 1 mW.ro FloatingPoint UNITS "dBm" .1.3.6.1.4.1.2696.3.2.1.6.7.1.10 |
iqAnalysisCS OBJECT IDENTIFIER .1.3.6.1.4.1.2696.3.2.1.6.9 |
merCSTableModulation Error Ratio (MER) SEQUENCE OF MerCSEntry .1.3.6.1.4.1.2696.3.2.1.6.9.2 |
merCSEntryRow specification MerCSEntry .1.3.6.1.4.1.2696.3.2.1.6.9.2.1 |
merCSInputNumberTransport Stream on which the measurement is made InputNumber .1.3.6.1.4.1.2696.3.2.1.6.9.2.1.1 |
merCSTestStateThis indicates whether the merCSValue is currently below the maximum limit.ro TestState .1.3.6.1.4.1.2696.3.2.1.6.9.2.1.2 |
merCSEnableDetermines whether the threshold test and associated traps for this measurement are enabled.rw Enable .1.3.6.1.4.1.2696.3.2.1.6.9.2.1.3 |
merCSCounterCount of the number of times a threshold error has occurred for this measurement.ro Counter32 .1.3.6.1.4.1.2696.3.2.1.6.9.2.1.4 |
merCSCounterDiscontinuityProvides the last time at which there was a discontinuity in the merCSCounter object.ro DateAndTime (SNMPv2-TC) .1.3.6.1.4.1.2696.3.2.1.6.9.2.1.5 |
merCSCounterResetmerCSCounter is reset to zero and merCSCounterDiscontinuity is set to the current time if 'true' is written to this object. When read, the value of this object is always 'false'.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.2696.3.2.1.6.9.2.1.6 |
merCSLatestErrorThe timestamp at the most recent occurrence of a threshold error on this measurement.ro DateAndTime (SNMPv2-TC) .1.3.6.1.4.1.2696.3.2.1.6.9.2.1.7 |
merCSActiveTimeThe total time when it has been possible to perform this measurementro ActiveTime UNITS "second" .1.3.6.1.4.1.2696.3.2.1.6.9.2.1.8 |
merCSMeasurementStateIndicates the validity of the measurementro MeasurementState .1.3.6.1.4.1.2696.3.2.1.6.9.2.1.9 |
merCSValueThe Modulation Error Ratio expressed in dBro FloatingPoint UNITS "dB" .1.3.6.1.4.1.2696.3.2.1.6.9.2.1.10 |
steCS OBJECT IDENTIFIER .1.3.6.1.4.1.2696.3.2.1.6.9.3 |
steMeanCSTableSystem Target Error (mean value) SEQUENCE OF SteMeanCSEntry .1.3.6.1.4.1.2696.3.2.1.6.9.3.1 |
steMeanCSEntryRow specification SteMeanCSEntry .1.3.6.1.4.1.2696.3.2.1.6.9.3.1.1 |
steMeanCSInputNumberTransport Stream on which the measurement is made InputNumber .1.3.6.1.4.1.2696.3.2.1.6.9.3.1.1.1 |
steMeanCSTestStateThis indicates whether the steMeanCSValue is currently within the thresholds.ro TestState .1.3.6.1.4.1.2696.3.2.1.6.9.3.1.1.2 |
steMeanCSEnableDetermines whether the threshold test and associated traps for this measurement are enabled.rw Enable .1.3.6.1.4.1.2696.3.2.1.6.9.3.1.1.3 |
steMeanCSCounterCount of the number of times a threshold error has occurred for this measurement.ro Counter32 .1.3.6.1.4.1.2696.3.2.1.6.9.3.1.1.4 |
steMeanCSCounterDiscontinuityProvides the last time at which there was a discontinuity in the counter object.ro DateAndTime (SNMPv2-TC) .1.3.6.1.4.1.2696.3.2.1.6.9.3.1.1.5 |
steMeanCSCounterResetThe counter object is reset to zero and the counter discontinuity object is set to the current time if 'true' is written to this object. When read, the value of this object is always 'false'.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.2696.3.2.1.6.9.3.1.1.6 |
steMeanCSLatestErrorThe timestamp at the most recent occurrence of a threshold error on this measurement.ro DateAndTime (SNMPv2-TC) .1.3.6.1.4.1.2696.3.2.1.6.9.3.1.1.7 |
steMeanCSActiveTimeThe total time when it has been possible to perform this measurementro ActiveTime UNITS "second" .1.3.6.1.4.1.2696.3.2.1.6.9.3.1.1.8 |
steMeanCSMeasurementStateIndicates the validity of the measurementro MeasurementState .1.3.6.1.4.1.2696.3.2.1.6.9.3.1.1.9 |
steMeanCSValueThe current System Target Error Mean as a numeric valuero FloatingPoint .1.3.6.1.4.1.2696.3.2.1.6.9.3.1.1.10 |
steDeviationCSTableSystem Target Error (deviation value) SEQUENCE OF SteDeviationCSEntry .1.3.6.1.4.1.2696.3.2.1.6.9.3.2 |
steDeviationCSEntryRow specification SteDeviationCSEntry .1.3.6.1.4.1.2696.3.2.1.6.9.3.2.1 |
steDeviationCSInputNumberTransport Stream on which the measurement is made InputNumber .1.3.6.1.4.1.2696.3.2.1.6.9.3.2.1.1 |
steDeviationCSTestStateThis indicates whether the steDeviationCSValue is currently within the thresholds.ro TestState .1.3.6.1.4.1.2696.3.2.1.6.9.3.2.1.2 |
steDeviationCSEnableDetermines whether the threshold test and associated traps for this measurement are enabled.rw Enable .1.3.6.1.4.1.2696.3.2.1.6.9.3.2.1.3 |
steDeviationCSCounterCount of the number of times a threshold error has occurred for this measurement.ro Counter32 .1.3.6.1.4.1.2696.3.2.1.6.9.3.2.1.4 |
steDeviationCSCounterDiscontinuityProvides the last time at which there was a discontinuity in the counter object.ro DateAndTime (SNMPv2-TC) .1.3.6.1.4.1.2696.3.2.1.6.9.3.2.1.5 |
steDeviationCSCounterResetThe counter object is reset to zero and the counter discontinuity object is set to the current time if 'true' is written to this object. When read, the value of this object is always 'false'.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.2696.3.2.1.6.9.3.2.1.6 |
steDeviationCSLatestErrorThe timestamp at the most recent occurrence of a threshold error on this measurement.ro DateAndTime (SNMPv2-TC) .1.3.6.1.4.1.2696.3.2.1.6.9.3.2.1.7 |
steDeviationCSActiveTimeThe total time when it has been possible to perform this measurementro ActiveTime UNITS "second" .1.3.6.1.4.1.2696.3.2.1.6.9.3.2.1.8 |
steDeviationCSMeasurementStateIndicates the validity of the measurementro MeasurementState .1.3.6.1.4.1.2696.3.2.1.6.9.3.2.1.9 |
steDeviationCSValueThe current System Target Error Deviation as a numeric valuero FloatingPoint .1.3.6.1.4.1.2696.3.2.1.6.9.3.2.1.10 |
csCSTableCarrier suppression measurement SEQUENCE OF CsCSEntry .1.3.6.1.4.1.2696.3.2.1.6.9.4 |
csCSEntryRow specification CsCSEntry .1.3.6.1.4.1.2696.3.2.1.6.9.4.1 |
csCSInputNumberTransport Stream on which the measurement is made InputNumber .1.3.6.1.4.1.2696.3.2.1.6.9.4.1.1 |
csCSTestStateThis indicates whether the csCSValue is currently within the thresholds.ro TestState .1.3.6.1.4.1.2696.3.2.1.6.9.4.1.2 |
csCSEnableDetermines whether the threshold test and associated traps for this measurement are enabled.rw Enable .1.3.6.1.4.1.2696.3.2.1.6.9.4.1.3 |
csCSCounterCount of the number of times a threshold error has occurred for this measurement.ro Counter32 .1.3.6.1.4.1.2696.3.2.1.6.9.4.1.4 |
csCSCounterDiscontinuityProvides the last time at which there was a discontinuity in the counter object.ro DateAndTime (SNMPv2-TC) .1.3.6.1.4.1.2696.3.2.1.6.9.4.1.5 |
csCSCounterResetThe counter object is reset to zero and the counter discontinuity object is set to the current time if 'true' is written to this object. When read, the value of this object is always 'false'.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.2696.3.2.1.6.9.4.1.6 |
csCSLatestErrorThe timestamp at the most recent occurrence of a threshold error on this measurement.ro DateAndTime (SNMPv2-TC) .1.3.6.1.4.1.2696.3.2.1.6.9.4.1.7 |
csCSActiveTimeThe total time when it has been possible to perform this measurementro ActiveTime UNITS "second" .1.3.6.1.4.1.2696.3.2.1.6.9.4.1.8 |
csCSMeasurementStateIndicates the validity of the measurementro MeasurementState .1.3.6.1.4.1.2696.3.2.1.6.9.4.1.9 |
csCSValueThe current Carrier Suppression value in dB.ro FloatingPoint UNITS "dB" .1.3.6.1.4.1.2696.3.2.1.6.9.4.1.10 |
aiCSTableAmplitude Imbalance (AI) measurement SEQUENCE OF AiCSEntry .1.3.6.1.4.1.2696.3.2.1.6.9.5 |
aiCSEntryRow specification AiCSEntry .1.3.6.1.4.1.2696.3.2.1.6.9.5.1 |
aiCSInputNumberTransport Stream on which the measurement is made InputNumber .1.3.6.1.4.1.2696.3.2.1.6.9.5.1.1 |
aiCSTestStateThis indicates whether the aiCSValue is currently within the thresholds.ro TestState .1.3.6.1.4.1.2696.3.2.1.6.9.5.1.2 |
aiCSEnableDetermines whether the threshold test and associated traps for this measurement are enabled.rw Enable .1.3.6.1.4.1.2696.3.2.1.6.9.5.1.3 |
aiCSCounterCount of the number of times a threshold error has occurred for this measurement.ro Counter32 .1.3.6.1.4.1.2696.3.2.1.6.9.5.1.4 |
aiCSCounterDiscontinuityProvides the last time at which there was a discontinuity in the counter object.ro DateAndTime (SNMPv2-TC) .1.3.6.1.4.1.2696.3.2.1.6.9.5.1.5 |
aiCSCounterResetThe counter object is reset to zero and the counter discontinuity object is set to the current time if 'true' is written to this object. When read, the value of this object is always 'false'.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.2696.3.2.1.6.9.5.1.6 |
aiCSLatestErrorThe timestamp at the most recent occurrence of a threshold error on this measurement.ro DateAndTime (SNMPv2-TC) .1.3.6.1.4.1.2696.3.2.1.6.9.5.1.7 |
aiCSActiveTimeThe total time when it has been possible to perform this measurementro ActiveTime UNITS "second" .1.3.6.1.4.1.2696.3.2.1.6.9.5.1.8 |
aiCSMeasurementStateIndicates the validity of the measurementro MeasurementState .1.3.6.1.4.1.2696.3.2.1.6.9.5.1.9 |
aiCSValueThe current Amplitude Imbalance as a percentagero FloatingPoint .1.3.6.1.4.1.2696.3.2.1.6.9.5.1.10 |
qeCSTableQuadrature Error (QE) measurement SEQUENCE OF QeCSEntry .1.3.6.1.4.1.2696.3.2.1.6.9.6 |
qeCSEntryRow specification QeCSEntry .1.3.6.1.4.1.2696.3.2.1.6.9.6.1 |
qeCSInputNumberTransport Stream on which the measurement is made InputNumber .1.3.6.1.4.1.2696.3.2.1.6.9.6.1.1 |
qeCSTestStateThis indicates whether the qeCSValue is currently within the thresholds.ro TestState .1.3.6.1.4.1.2696.3.2.1.6.9.6.1.2 |
qeCSEnableDetermines whether the threshold test and associated traps for this measurement are enabled.rw Enable .1.3.6.1.4.1.2696.3.2.1.6.9.6.1.3 |
qeCSCounterCount of the number of times a threshold error has occurred for this measurement.ro Counter32 .1.3.6.1.4.1.2696.3.2.1.6.9.6.1.4 |
qeCSCounterDiscontinuityProvides the last time at which there was a discontinuity in the counter object.ro DateAndTime (SNMPv2-TC) .1.3.6.1.4.1.2696.3.2.1.6.9.6.1.5 |
qeCSCounterResetThe counter object is reset to zero and the counter discontinuity object is set to the current time if 'true' is written to this object. When read, the value of this object is always 'false'.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.2696.3.2.1.6.9.6.1.6 |
qeCSLatestErrorThe timestamp at the most recent occurrence of a threshold error on this measurement.ro DateAndTime (SNMPv2-TC) .1.3.6.1.4.1.2696.3.2.1.6.9.6.1.7 |
qeCSActiveTimeThe total time when it has been possible to perform this measurementro ActiveTime UNITS "second" .1.3.6.1.4.1.2696.3.2.1.6.9.6.1.8 |
qeCSMeasurementStateIndicates the validity of the measurementro MeasurementState .1.3.6.1.4.1.2696.3.2.1.6.9.6.1.9 |
qeCSValueThe current Quadrature Error value in degrees.ro FloatingPoint UNITS "degree" .1.3.6.1.4.1.2696.3.2.1.6.9.6.1.10 |
rteCSTableResidual Target Error (RTE) measurement SEQUENCE OF RteCSEntry .1.3.6.1.4.1.2696.3.2.1.6.9.7 |
rteCSEntryRow description RteCSEntry .1.3.6.1.4.1.2696.3.2.1.6.9.7.1 |
rteCSInputNumberTransport Stream on which the measurement is made InputNumber .1.3.6.1.4.1.2696.3.2.1.6.9.7.1.1 |
rteCSTestStateThis indicates whether the rteCSValue is currently within the thresholds.ro TestState .1.3.6.1.4.1.2696.3.2.1.6.9.7.1.2 |
rteCSEnableDetermines whether the threshold test and associated traps for this measurement are enabled.rw Enable .1.3.6.1.4.1.2696.3.2.1.6.9.7.1.3 |
rteCSCounterCount of the number of times a threshold error has occurred for this measurement.ro Counter32 .1.3.6.1.4.1.2696.3.2.1.6.9.7.1.4 |
rteCSCounterDiscontinuityProvides the last time at which there was a discontinuity in the counter object.ro DateAndTime (SNMPv2-TC) .1.3.6.1.4.1.2696.3.2.1.6.9.7.1.5 |
rteCSCounterResetThe counter object is reset to zero and the counter discontinuity object is set to the current time if 'true' is written to this object. When read, the value of this object is always 'false'.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.2696.3.2.1.6.9.7.1.6 |
rteCSLatestErrorThe timestamp at the most recent occurrence of a threshold error on this measurement.ro DateAndTime (SNMPv2-TC) .1.3.6.1.4.1.2696.3.2.1.6.9.7.1.7 |
rteCSActiveTimeThe total time when it has been possible to perform this measurementro ActiveTime UNITS "second" .1.3.6.1.4.1.2696.3.2.1.6.9.7.1.8 |
rteCSMeasurementStateIndicates the validity of the measurementro MeasurementState .1.3.6.1.4.1.2696.3.2.1.6.9.7.1.9 |
rteCSValueThe current Residual Target Error value as a numeric value.ro FloatingPoint .1.3.6.1.4.1.2696.3.2.1.6.9.7.1.10 |
ciCSTableCoherent Interferer measurement SEQUENCE OF CiCSEntry .1.3.6.1.4.1.2696.3.2.1.6.9.8 |
ciCSEntryRow specification CiCSEntry .1.3.6.1.4.1.2696.3.2.1.6.9.8.1 |
ciCSInputNumberTransport Stream on which the measurement is made InputNumber .1.3.6.1.4.1.2696.3.2.1.6.9.8.1.1 |
ciCSTestStateThis indicates whether the ciCSValue is currently within the thresholds.ro TestState .1.3.6.1.4.1.2696.3.2.1.6.9.8.1.2 |
ciCSEnableDetermines whether the threshold test and associated traps for this measurement are enabled.rw Enable .1.3.6.1.4.1.2696.3.2.1.6.9.8.1.3 |
ciCSCounterCount of the number of times a threshold error has occurred for this measurement.ro Counter32 .1.3.6.1.4.1.2696.3.2.1.6.9.8.1.4 |
ciCSCounterDiscontinuityProvides the last time at which there was a discontinuity in the counter object.ro DateAndTime (SNMPv2-TC) .1.3.6.1.4.1.2696.3.2.1.6.9.8.1.5 |
ciCSCounterResetThe counter object is reset to zero and the counter discontinuity object is set to the current time if 'true' is written to this object. When read, the value of this object is always 'false'.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.2696.3.2.1.6.9.8.1.6 |
ciCSLatestErrorThe timestamp at the most recent occurrence of a threshold error on this measurement.ro DateAndTime (SNMPv2-TC) .1.3.6.1.4.1.2696.3.2.1.6.9.8.1.7 |
ciCSActiveTimeThe total time when it has been possible to perform this measurementro ActiveTime UNITS "second" .1.3.6.1.4.1.2696.3.2.1.6.9.8.1.8 |
ciCSMeasurementStateIndicates the validity of the measurementro MeasurementState .1.3.6.1.4.1.2696.3.2.1.6.9.8.1.9 |
ciCSValueThe current Coherent Interferer value in dB.ro FloatingPoint UNITS "dB" .1.3.6.1.4.1.2696.3.2.1.6.9.8.1.10 |
pjCSTablePhase Jitter (PJ) measurement SEQUENCE OF PjCSEntry .1.3.6.1.4.1.2696.3.2.1.6.9.9 |
pjCSEntryRow specification PjCSEntry .1.3.6.1.4.1.2696.3.2.1.6.9.9.1 |
pjCSInputNumberTransport Stream on which the measurement is made InputNumber .1.3.6.1.4.1.2696.3.2.1.6.9.9.1.1 |
pjCSTestStateThis indicates whether the pjCSValue is currently within the thresholds.ro TestState .1.3.6.1.4.1.2696.3.2.1.6.9.9.1.2 |
pjCSEnableDetermines whether the threshold test and associated traps for this measurement are enabled.rw Enable .1.3.6.1.4.1.2696.3.2.1.6.9.9.1.3 |
pjCSCounterCount of the number of times a threshold error has occurred for this measurement.ro Counter32 .1.3.6.1.4.1.2696.3.2.1.6.9.9.1.4 |
pjCSCounterDiscontinuityProvides the last time at which there was a discontinuity in the counter object.ro DateAndTime (SNMPv2-TC) .1.3.6.1.4.1.2696.3.2.1.6.9.9.1.5 |
pjCSCounterResetThe counter object is reset to zero and the counter discontinuity object is set to the current time if 'true' is written to this object. When read, the value of this object is always 'false'.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.2696.3.2.1.6.9.9.1.6 |
pjCSLatestErrorThe timestamp at the most recent occurrence of a threshold error on this measurement.ro DateAndTime (SNMPv2-TC) .1.3.6.1.4.1.2696.3.2.1.6.9.9.1.7 |
pjCSActiveTimeThe total time when it has been possible to perform this measurementro ActiveTime UNITS "second" .1.3.6.1.4.1.2696.3.2.1.6.9.9.1.8 |
pjCSMeasurementStateIndicates the validity of the measurementro MeasurementState .1.3.6.1.4.1.2696.3.2.1.6.9.9.1.9 |
pjCSValueThe current Phase Jitter value in degrees.ro FloatingPoint UNITS "degree" .1.3.6.1.4.1.2696.3.2.1.6.9.9.1.10 |
snrCSTableSignal-to-Noise Ratio (SNR) SEQUENCE OF SnrCSEntry .1.3.6.1.4.1.2696.3.2.1.6.9.10 |
snrCSEntryRow specification SnrCSEntry .1.3.6.1.4.1.2696.3.2.1.6.9.10.1 |
snrCSInputNumberTransport Stream on which the measurement is made InputNumber .1.3.6.1.4.1.2696.3.2.1.6.9.10.1.1 |
snrCSTestStateThis indicates whether the snrCSValue is currently within the thresholds.ro TestState .1.3.6.1.4.1.2696.3.2.1.6.9.10.1.2 |
snrCSEnableDetermines whether the threshold test and associated traps for this measurement are enabled.rw Enable .1.3.6.1.4.1.2696.3.2.1.6.9.10.1.3 |
snrCSCounterCount of the number of times a threshold error has occurred for this measurement.ro Counter32 .1.3.6.1.4.1.2696.3.2.1.6.9.10.1.4 |
snrCSCounterDiscontinuityProvides the last time at which there was a discontinuity in the counter object.ro DateAndTime (SNMPv2-TC) .1.3.6.1.4.1.2696.3.2.1.6.9.10.1.5 |
snrCSCounterResetThe counter object is reset to zero and the counter discontinuity object is set to the current time if 'true' is written to this object. When read, the value of this object is always 'false'.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.2696.3.2.1.6.9.10.1.6 |
snrCSLatestErrorThe timestamp at the most recent occurrence of a threshold error on this measurement.ro DateAndTime (SNMPv2-TC) .1.3.6.1.4.1.2696.3.2.1.6.9.10.1.7 |
snrCSActiveTimeThe total time when it has been possible to perform this measurementro ActiveTime UNITS "second" .1.3.6.1.4.1.2696.3.2.1.6.9.10.1.8 |
snrCSMeasurementStateIndicates the validity of the measurementro MeasurementState .1.3.6.1.4.1.2696.3.2.1.6.9.10.1.9 |
snrCSValueThe current Signal-to-Noise value in dB.ro FloatingPoint UNITS "dB" .1.3.6.1.4.1.2696.3.2.1.6.9.10.1.10 |
cableSatPreferencesTableTable containing per input configuration information for cable and satellite common measurements. SEQUENCE OF CableSatPreferencesEntry .1.3.6.1.4.1.2696.3.2.1.6.100 |
cableSatPreferencesEntryRow specification CableSatPreferencesEntry .1.3.6.1.4.1.2696.3.2.1.6.100.1 |
cableSatPrefInputNumberTransport Stream input to which the preferences apply InputNumber .1.3.6.1.4.1.2696.3.2.1.6.100.1.1 |
cableSatPrefCentreFrequencyThis is the centre frequency to which the measuring equipment is tuned for making cable and satellite measurements. This frequency is the actual input frequency to the measuring equipment, which may be at an intermediate frequency (IF) rather than the final RF. This setting affects the objects in the 'tr101290Cable' and 'tr101290Satellite' branches of the MIB as well as the 'tr101290CableSat' branch.rw FloatingPoint UNITS "MHz" .1.3.6.1.4.1.2696.3.2.1.6.100.1.2 |
cableSatPrefModulationThis is the modulation which the measuring equipment expects to see and against which it makes modulation measurements. This applies to cable and satellite measurements. This setting affects the objects in the 'tr101290Cable' and 'tr101290Satellite' branches of the MIB as well as the 'tr101290CableSat' branch.rw Modulation .1.3.6.1.4.1.2696.3.2.1.6.100.1.3 |
cableSatPrefSysAvailUATModeDetermines whether the 'N consecutive' or 'rolling window' mode of determining the start of a period of Unavailable Time (UAT) is used. If the 'N consecutive' mode is selected, the 'M' and 'T' preference parameters are ignored. Likewise, if the 'rolling window' mode is selected, the 'N' preference parameter is ignored.rw UATMode .1.3.6.1.4.1.2696.3.2.1.6.100.1.4 |
cableSatPrefSysAvailNThe N value used to identify the start and end of a period of unavailable time (UAT).rw Unsigned32 .1.3.6.1.4.1.2696.3.2.1.6.100.1.5 |
cableSatPrefSysAvailTThe T value used to identify the start and end of a period of unavailable time (UAT).rw FloatingPoint UNITS "second" .1.3.6.1.4.1.2696.3.2.1.6.100.1.6 |
cableSatPrefSysAvailMThe M value used to identify the start and end of a period of unavailable time (UAT).rw Unsigned32 .1.3.6.1.4.1.2696.3.2.1.6.100.1.7 |
cableSatPrefSysAvailTIEach Time Interval of this length is assessed as to whether it is a Severely Errored Time Interval.rw FloatingPoint UNITS "second" .1.3.6.1.4.1.2696.3.2.1.6.100.1.8 |
cableSatPrefSysAvailEBPerCentIf more than this percentage of blocks within a Time Interval is an Errored Block, the Time Interval is a Severely Errored Time Interval (SETI). Example values are: '1.53', '10', '0.33'.rw FloatingPoint .1.3.6.1.4.1.2696.3.2.1.6.100.1.9 |
cableSatPrefSysAvailTotalTimeThe Total Time over which the System Availability is calculated.rw FloatingPoint UNITS "second" .1.3.6.1.4.1.2696.3.2.1.6.100.1.10 |
cableSatPrefLinkAvailUATModeDetermines whether the 'N consecutive' or 'rolling window' mode of determining the start of a period of Link Unavailable Time (LUAT) is used. If the 'N consecutive' mode is selected, the 'M' and 'T' preference parameters are ignored. Likewise, if the 'rolling window' mode is selected, the 'N' preference parameter is ignored.rw UATMode .1.3.6.1.4.1.2696.3.2.1.6.100.1.11 |
cableSatPrefLinkAvailNThe N value used to identify the start and end of a period of Link Unavailable Time (LUAT).rw Unsigned32 .1.3.6.1.4.1.2696.3.2.1.6.100.1.12 |
cableSatPrefLinkAvailTThe T value used to identify the start and end of a period of Link Unavailable Time (LUAT).rw FloatingPoint UNITS "second" .1.3.6.1.4.1.2696.3.2.1.6.100.1.13 |
cableSatPrefLinkAvailMThe M value used to identify the start and end of a period of Link Unavailable Time (LUAT).rw Unsigned32 .1.3.6.1.4.1.2696.3.2.1.6.100.1.14 |
cableSatPrefLinkAvailTIEach Time Interval of this length is assessed as to whether it is a Severely Uncorrectable Time Interval (SUTI).rw FloatingPoint UNITS "second" .1.3.6.1.4.1.2696.3.2.1.6.100.1.15 |
cableSatPrefLinkAvailUPPerCentIf more than this percentage of packets within a Time Interval is an Uncorrectable Packet (UP), the Time Interval is a Severely Uncorrectable Time Interval (SUTI). Example values are: '1.53', '10', '0.33'.rw FloatingPoint .1.3.6.1.4.1.2696.3.2.1.6.100.1.16 |
cableSatPrefLinkAvailTotalTimeThe Total Time over which the Link Availability is calculated.rw FloatingPoint UNITS "second" .1.3.6.1.4.1.2696.3.2.1.6.100.1.17 |
cableSatPrefBERMaxIf the berRSinServiceValue exceeds this value, the associated test fails.rw FloatingPoint .1.3.6.1.4.1.2696.3.2.1.6.100.1.18 |
cableSatPrefSignalPowerMinIf the power measured by rfIFsignalPowerValue is less than this value, the associated test fails.rw FloatingPoint UNITS "dBm" .1.3.6.1.4.1.2696.3.2.1.6.100.1.19 |
cableSatPrefSignalPowerMaxIf the power measured by rfIFsignalPowerValue is greater than this value, the associated test fails.rw FloatingPoint UNITS "dBm" .1.3.6.1.4.1.2696.3.2.1.6.100.1.20 |
cableSatPrefNoisePowerMaxIf the noise power measured by noisePowerValue exceeds this value, the associated test fails.rw FloatingPoint UNITS "dBm" .1.3.6.1.4.1.2696.3.2.1.6.100.1.21 |
cableSatPrefMerCSMinIf the merCSValue is less than this value, the associated test fails.rw FloatingPoint UNITS "dB" .1.3.6.1.4.1.2696.3.2.1.6.100.1.22 |
cableSatPrefSteMeanCSMaxIf the steMeanCSValue exceeds this value, the associated test fails.rw FloatingPoint UNITS "dB" .1.3.6.1.4.1.2696.3.2.1.6.100.1.23 |
cableSatPrefSteDeviationCSMaxIf the steDeviationCSValue exceeds this value, the associated test fails.rw FloatingPoint UNITS "dB" .1.3.6.1.4.1.2696.3.2.1.6.100.1.24 |
cableSatPrefCsCSMinIf the csCSValue is less than this value, the associated test failsrw FloatingPoint UNITS "dB" .1.3.6.1.4.1.2696.3.2.1.6.100.1.25 |
cableSatPrefAiCSMaxIf aiCSValue exceeds this value, the associated test fails.rw FloatingPoint UNITS "dB" .1.3.6.1.4.1.2696.3.2.1.6.100.1.26 |
cableSatPrefQeCSMaxIf qeCSValue exceeds this value, the associated test fails.rw FloatingPoint UNITS "dB" .1.3.6.1.4.1.2696.3.2.1.6.100.1.27 |
cableSatPrefRteCSMaxIf rteCSValue exceeds this value, the associated test fails.rw FloatingPoint UNITS "dB" .1.3.6.1.4.1.2696.3.2.1.6.100.1.28 |
cableSatPrefCiCSMinIf ciCSValue is less than this value, the associated test fails.rw FloatingPoint UNITS "dB" .1.3.6.1.4.1.2696.3.2.1.6.100.1.29 |
cableSatPrefPjCSMaxIf pjCSValue exceeds this value, the associated test fails.rw FloatingPoint UNITS "dB" .1.3.6.1.4.1.2696.3.2.1.6.100.1.30 |
cableSatPrefSnrCSMinIf snrCSValue is less than this value, the associated test fails.rw FloatingPoint UNITS "dB" .1.3.6.1.4.1.2696.3.2.1.6.100.1.31 |
tr101290Cable OBJECT IDENTIFIER .1.3.6.1.4.1.2696.3.2.1.7 |
noiseMarginTableNoise margin measurement SEQUENCE OF NoiseMarginEntry .1.3.6.1.4.1.2696.3.2.1.7.1 |
noiseMarginEntryRow description NoiseMarginEntry .1.3.6.1.4.1.2696.3.2.1.7.1.1 |
noiseMarginInputNumberTransport Stream on which the measurement is made InputNumber .1.3.6.1.4.1.2696.3.2.1.7.1.1.1 |
noiseMarginTestStateThis indicates whether the noiseMarginValue is currently within the thresholds.ro TestState .1.3.6.1.4.1.2696.3.2.1.7.1.1.2 |
noiseMarginEnableDetermines whether the threshold test and associated traps for this measurement are enabled.rw Enable .1.3.6.1.4.1.2696.3.2.1.7.1.1.3 |
noiseMarginCounterCount of the number of times a threshold error has occurred for this measurement.ro Counter32 .1.3.6.1.4.1.2696.3.2.1.7.1.1.4 |
noiseMarginCounterDiscontinuityProvides the last time at which there was a discontinuity in the counter object.ro DateAndTime (SNMPv2-TC) .1.3.6.1.4.1.2696.3.2.1.7.1.1.5 |
noiseMarginCounterResetThe counter object is reset to zero and the counter discontinuity object is set to the current time if 'true' is written to this object. When read, the value of this object is always 'false'.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.2696.3.2.1.7.1.1.6 |
noiseMarginLatestErrorThe timestamp at the most recent occurrence of a threshold error on this measurement.ro DateAndTime (SNMPv2-TC) .1.3.6.1.4.1.2696.3.2.1.7.1.1.7 |
noiseMarginActiveTimeThe total time when it has been possible to perform this measurementro ActiveTime UNITS "second" .1.3.6.1.4.1.2696.3.2.1.7.1.1.8 |
noiseMarginMeasurementStateIndicates the validity of the measurementro MeasurementState .1.3.6.1.4.1.2696.3.2.1.7.1.1.9 |
noiseMarginValueThe current Noise Margin value in dB.ro FloatingPoint UNITS "dB" .1.3.6.1.4.1.2696.3.2.1.7.1.1.10 |
estNoiseMarginTableEstimated noise margin measurement SEQUENCE OF EstNoiseMarginEntry .1.3.6.1.4.1.2696.3.2.1.7.2 |
estNoiseMarginEntryRow description EstNoiseMarginEntry .1.3.6.1.4.1.2696.3.2.1.7.2.1 |
estNoiseMarginInputNumberTransport Stream on which the measurement is made InputNumber .1.3.6.1.4.1.2696.3.2.1.7.2.1.1 |
estNoiseMarginTestStateThis indicates whether the estNoiseMarginValue is currently within the thresholds.ro TestState .1.3.6.1.4.1.2696.3.2.1.7.2.1.2 |
estNoiseMarginEnableDetermines whether the threshold test and associated traps for this measurement are enabled.rw Enable .1.3.6.1.4.1.2696.3.2.1.7.2.1.3 |
estNoiseMarginCounterCount of the number of times a threshold error has occurred for this measurement.ro Counter32 .1.3.6.1.4.1.2696.3.2.1.7.2.1.4 |
estNoiseMarginCounterDiscontinuityProvides the last time at which there was a discontinuity in the counter object.ro DateAndTime (SNMPv2-TC) .1.3.6.1.4.1.2696.3.2.1.7.2.1.5 |
estNoiseMarginCounterResetThe counter object is reset to zero and the counter discontinuity object is set to the current time if 'true' is written to this object. When read, the value of this object is always 'false'.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.2696.3.2.1.7.2.1.6 |
estNoiseMarginLatestErrorThe timestamp at the most recent occurrence of a threshold error on this measurement.ro DateAndTime (SNMPv2-TC) .1.3.6.1.4.1.2696.3.2.1.7.2.1.7 |
estNoiseMarginActiveTimeThe total time when it has been possible to perform this measurementro ActiveTime UNITS "second" .1.3.6.1.4.1.2696.3.2.1.7.2.1.8 |
estNoiseMarginMeasurementStateIndicates the validity of the measurementro MeasurementState .1.3.6.1.4.1.2696.3.2.1.7.2.1.9 |
estNoiseMarginValueThe current Estimated Noise Margin value in dB.ro FloatingPoint UNITS "dB" .1.3.6.1.4.1.2696.3.2.1.7.2.1.10 |
signQualMarTTableSignal quality margin test SEQUENCE OF SignQualMarTEntry .1.3.6.1.4.1.2696.3.2.1.7.3 |
signQualMarTEntryRow description SignQualMarTEntry .1.3.6.1.4.1.2696.3.2.1.7.3.1 |
signQualMarTInputNumberTransport Stream on which the test is done InputNumber .1.3.6.1.4.1.2696.3.2.1.7.3.1.1 |
signQualMarTTestStateThis indicates an error if the percentage of IQ points outside the threshold box exceeds cablePrefSignQualPercentMax.ro TestState .1.3.6.1.4.1.2696.3.2.1.7.3.1.2 |
signQualMarTEnableDetermines whether the threshold test and associated traps for this measurement are enabled.rw Enable .1.3.6.1.4.1.2696.3.2.1.7.3.1.3 |
signQualMarTCounterCount of the number of times an error has occurred.ro Counter32 .1.3.6.1.4.1.2696.3.2.1.7.3.1.4 |
signQualMarTCounterDiscontinuityProvides the last time at which there was a discontinuity in the counter object.ro DateAndTime (SNMPv2-TC) .1.3.6.1.4.1.2696.3.2.1.7.3.1.5 |
signQualMarTCounterResetThe counter object is reset to zero and the counter discontinuity object is set to the current time if 'true' is written to this object. When read, the value of this object is always 'false'.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.2696.3.2.1.7.3.1.6 |
signQualMarTLatestErrorThe timestamp at the most recent occurrence of an error.ro DateAndTime (SNMPv2-TC) .1.3.6.1.4.1.2696.3.2.1.7.3.1.7 |
signQualMarTActiveTimeThe total time when it has been possible to perform this measurementro ActiveTime UNITS "second" .1.3.6.1.4.1.2696.3.2.1.7.3.1.8 |
eNDCTableEquivalent Noise Degradation (END) measurement SEQUENCE OF ENDCEntry .1.3.6.1.4.1.2696.3.2.1.7.4 |
eNDCEntryRow description ENDCEntry .1.3.6.1.4.1.2696.3.2.1.7.4.1 |
eNDCInputNumberTransport Stream on which the measurement is made InputNumber .1.3.6.1.4.1.2696.3.2.1.7.4.1.1 |
eNDCTestStateThis indicates an error when the eNDCValue exceeds the threshold.ro TestState .1.3.6.1.4.1.2696.3.2.1.7.4.1.2 |
eNDCEnableDetermines whether the threshold test and associated traps for this measurement are enabled.rw Enable .1.3.6.1.4.1.2696.3.2.1.7.4.1.3 |
eNDCCounterCount of the number of times a threshold error has occurred for this measurement.ro Counter32 .1.3.6.1.4.1.2696.3.2.1.7.4.1.4 |
eNDCCounterDiscontinuityProvides the last time at which there was a discontinuity in the counter object.ro DateAndTime (SNMPv2-TC) .1.3.6.1.4.1.2696.3.2.1.7.4.1.5 |
eNDCCounterResetThe counter object is reset to zero and the counter discontinuity object is set to the current time if 'true' is written to this object. When read, the value of this object is always 'false'.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.2696.3.2.1.7.4.1.6 |
eNDCLatestErrorThe timestamp at the most recent occurrence of a threshold error on this measurement.ro DateAndTime (SNMPv2-TC) .1.3.6.1.4.1.2696.3.2.1.7.4.1.7 |
eNDCActiveTimeThe total time when it has been possible to perform this measurementro ActiveTime UNITS "second" .1.3.6.1.4.1.2696.3.2.1.7.4.1.8 |
eNDCMeasurementStateIndicates the validity of the measurementro MeasurementState .1.3.6.1.4.1.2696.3.2.1.7.4.1.9 |
eNDCValueThe current Equivalent Noise Degradation value in dB.ro FloatingPoint UNITS "dB" .1.3.6.1.4.1.2696.3.2.1.7.4.1.10 |
outBandEmissTableOut of band emissions test SEQUENCE OF OutBandEmissEntry .1.3.6.1.4.1.2696.3.2.1.7.5 |
outBandEmissEntryRow specification OutBandEmissEntry .1.3.6.1.4.1.2696.3.2.1.7.5.1 |
outBandEmissInputNumberTransport Stream on which the test is made InputNumber .1.3.6.1.4.1.2696.3.2.1.7.5.1.1 |
outBandEmissTestStateThis indicates whether the spectrum is within the spectrum mask. Note that the spectrum mask must be provided to the instrument by means outside the scope of this MIB.ro TestState .1.3.6.1.4.1.2696.3.2.1.7.5.1.2 |
outBandEmissEnableDetermines whether the threshold test and associated traps for this measurement are enabled.rw Enable .1.3.6.1.4.1.2696.3.2.1.7.5.1.3 |
outBandEmissCounterCount of the number of times an error has occurred for this test.ro Counter32 .1.3.6.1.4.1.2696.3.2.1.7.5.1.4 |
outBandEmissCounterDiscontinuityProvides the last time at which there was a discontinuity in the counter object.ro DateAndTime (SNMPv2-TC) .1.3.6.1.4.1.2696.3.2.1.7.5.1.5 |
outBandEmissCounterResetThe counter object is reset to zero and the counter discontinuity object is set to the current time if 'true' is written to this object. When read, the value of this object is always 'false'.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.2696.3.2.1.7.5.1.6 |
outBandEmissLatestErrorThe timestamp at the most recent occurrence of an error on this test.ro DateAndTime (SNMPv2-TC) .1.3.6.1.4.1.2696.3.2.1.7.5.1.7 |
outBandEmissActiveTimeThe total time when it has been possible to perform this measurementro ActiveTime UNITS "second" .1.3.6.1.4.1.2696.3.2.1.7.5.1.8 |
cablePreferencesTableTable containing per input preferences for cable measurements. SEQUENCE OF CablePreferencesEntry .1.3.6.1.4.1.2696.3.2.1.7.100 |
cablePreferencesEntryRow specification CablePreferencesEntry .1.3.6.1.4.1.2696.3.2.1.7.100.1 |
cablePrefInputNumberTransport Stream input to which the preferences apply InputNumber .1.3.6.1.4.1.2696.3.2.1.7.100.1.1 |
cablePrefNoiseMarginMinIf the measured noiseMarginValue is less than this value the associated test fails.rw FloatingPoint UNITS "dB" .1.3.6.1.4.1.2696.3.2.1.7.100.1.2 |
cablePrefEstNoiseMarginMinIf the measured estNoiseMarginValue is less than this value the associated test fails.rw FloatingPoint UNITS "dB" .1.3.6.1.4.1.2696.3.2.1.7.100.1.3 |
cablePrefSignQualBoxSizeThis object determines the size of the quality threshold box for the signal quality margin test. The quality threshold box is assumed to be square. The value is the ratio of the length of one side of a threshold box to the length of one side of the IQ decision boundary box. An example value is '0.5'.rw FloatingPoint .1.3.6.1.4.1.2696.3.2.1.7.100.1.4 |
cablePrefSignQualPercentMaxThis object sets the limit on how many constellation points may fall outside the threshold box before the signal quality margin test fails. The value is expressed as a percentage, for example '7.5'.rw Integer32 .1.3.6.1.4.1.2696.3.2.1.7.100.1.5 |
cablePrefENDBERBER value which is to be used for the END measurement.rw FloatingPoint .1.3.6.1.4.1.2696.3.2.1.7.100.1.6 |
cablePrefENDCtoNSpecifiedThis determines whether cablePrefENDIdeal is expressed as a C/N ratio (value is true) or an Eb/No ratio (value is false).rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.2696.3.2.1.7.100.1.7 |
cablePrefENDIdealThis is the 'ideal' value of C/N or Eb/No for the given BER.rw FloatingPoint UNITS "dB" .1.3.6.1.4.1.2696.3.2.1.7.100.1.8 |
cablePrefENDMaxIf the measured END exceeds this value the associated test fails.rw FloatingPoint UNITS "dB" .1.3.6.1.4.1.2696.3.2.1.7.100.1.9 |
tr101290Satellite OBJECT IDENTIFIER .1.3.6.1.4.1.2696.3.2.1.8 |
berViterbiSTableBER before Viterbi decoding measurement SEQUENCE OF BerViterbiSEntry .1.3.6.1.4.1.2696.3.2.1.8.1 |
berViterbiSEntryRow description BerViterbiSEntry .1.3.6.1.4.1.2696.3.2.1.8.1.1 |
berViterbiSInputNumberTransport Stream on which the measurement is made InputNumber .1.3.6.1.4.1.2696.3.2.1.8.1.1.1 |
berViterbiSTestStateThis test fails if either berViterbiSIValue or berViterbiSQValue exceeds the threshold set by satellitePrefBERMax.ro TestState .1.3.6.1.4.1.2696.3.2.1.8.1.1.2 |
berViterbiSEnableDetermines whether the threshold test and associated traps for this measurement are enabled.rw Enable .1.3.6.1.4.1.2696.3.2.1.8.1.1.3 |
berViterbiSCounterCount of the number of times a threshold error has occurred for this measurement.ro Counter32 .1.3.6.1.4.1.2696.3.2.1.8.1.1.4 |
berViterbiSCounterDiscontinuityProvides the last time at which there was a discontinuity in the berViterbiSCounter object.ro DateAndTime (SNMPv2-TC) .1.3.6.1.4.1.2696.3.2.1.8.1.1.5 |
berViterbiSCounterResetThe counter object is reset to zero and the counter discontinuity object is set to the current time if 'true' is written to this object. When read, the value of this object is always 'false'.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.2696.3.2.1.8.1.1.6 |
berViterbiSLatestErrorThe timestamp at the most recent occurrence of a threshold error on this measurement.ro DateAndTime (SNMPv2-TC) .1.3.6.1.4.1.2696.3.2.1.8.1.1.7 |
berViterbiSActiveTimeThe total time when it has been possible to perform this measurementro ActiveTime UNITS "second" .1.3.6.1.4.1.2696.3.2.1.8.1.1.8 |
berViterbiSMeasurementStateIndicates the validity of the measurementro MeasurementState .1.3.6.1.4.1.2696.3.2.1.8.1.1.9 |
berViterbiSIValueThis is the pre-Viterbi I path BER value, for example 0.0000023ro FloatingPoint .1.3.6.1.4.1.2696.3.2.1.8.1.1.10 |
berViterbiSQValueThis is the pre-Viterbi Q path BER value, for example 0.0000023ro FloatingPoint .1.3.6.1.4.1.2696.3.2.1.8.1.1.11 |
berViterbiSMeasurementMethodThis indicates whether the measurement was made separately for the I and Q parts of the signal or by a measurement of I and Q combined.ro BERMeasurementMethod .1.3.6.1.4.1.2696.3.2.1.8.1.1.12 |
ifSpectrumTableIF spectrum test SEQUENCE OF IfSpectrumEntry .1.3.6.1.4.1.2696.3.2.1.8.2 |
ifSpectrumEntryRow specification IfSpectrumEntry .1.3.6.1.4.1.2696.3.2.1.8.2.1 |
ifSpectrumInputNumberTransport Stream on which the measurement is made InputNumber .1.3.6.1.4.1.2696.3.2.1.8.2.1.1 |
ifSpectrumTestStateThis indicates whether the spectrum conforms to the template. Note that the spectrum mask must be provided to the instrument by means outside the scope of this MIB. The group delay is not tested.ro TestState .1.3.6.1.4.1.2696.3.2.1.8.2.1.2 |
ifSpectrumEnableDetermines whether the threshold test and associated traps for this measurement are enabled.rw Enable .1.3.6.1.4.1.2696.3.2.1.8.2.1.3 |
ifSpectrumCounterCount of the number of times an error has occurred for this test.ro Counter32 .1.3.6.1.4.1.2696.3.2.1.8.2.1.4 |
ifSpectrumCounterDiscontinuityProvides the last time at which there was a discontinuity in the counter object.ro DateAndTime (SNMPv2-TC) .1.3.6.1.4.1.2696.3.2.1.8.2.1.5 |
ifSpectrumCounterResetThe counter object is reset to zero and the counter discontinuity object is set to the current time if 'true' is written to this object. When read, the value of this object is always 'false'.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.2696.3.2.1.8.2.1.6 |
ifSpectrumLatestErrorThe timestamp at the most recent occurrence of an error on this test.ro DateAndTime (SNMPv2-TC) .1.3.6.1.4.1.2696.3.2.1.8.2.1.7 |
ifSpectrumActiveTimeThe total time when it has been possible to perform this measurementro ActiveTime UNITS "second" .1.3.6.1.4.1.2696.3.2.1.8.2.1.8 |
satellitePreferencesTableTable of satellite specific measurement preferences. SEQUENCE OF SatellitePreferencesEntry .1.3.6.1.4.1.2696.3.2.1.8.100 |
satellitePreferencesEntryRow specification SatellitePreferencesEntry .1.3.6.1.4.1.2696.3.2.1.8.100.1 |
satellitePrefInputNumberTransport Stream input to which the preferences apply InputNumber .1.3.6.1.4.1.2696.3.2.1.8.100.1.1 |
satellitePrefBERMaxThis defines the upper limit on the BER before Viterbi measurementrw FloatingPoint .1.3.6.1.4.1.2696.3.2.1.8.100.1.2 |
tr101290Terrestrial OBJECT IDENTIFIER .1.3.6.1.4.1.2696.3.2.1.9 |
rfTerr OBJECT IDENTIFIER .1.3.6.1.4.1.2696.3.2.1.9.1 |
rfAccuracyTableRF frequency accuracy (Precision) SEQUENCE OF RfAccuracyEntry .1.3.6.1.4.1.2696.3.2.1.9.1.1 |
rfAccuracyEntryRow specification RfAccuracyEntry .1.3.6.1.4.1.2696.3.2.1.9.1.1.1 |
rfAccuracyInputNumberRF input on which the measurement is made InputNumber .1.3.6.1.4.1.2696.3.2.1.9.1.1.1.1 |
rfAccuracyTestStateThis indicates whether the rfAccuracyValue is within the thresholds.ro TestState .1.3.6.1.4.1.2696.3.2.1.9.1.1.1.2 |
rfAccuracyEnableDetermines whether the threshold test and associated traps for this measurement are enabled.rw Enable .1.3.6.1.4.1.2696.3.2.1.9.1.1.1.3 |
rfAccuracyCounterCount of the number of times a threshold error has occurred for this measurement.ro Counter32 .1.3.6.1.4.1.2696.3.2.1.9.1.1.1.4 |
rfAccuracyCounterDiscontinuityProvides the last time at which there was a discontinuity in the counter object.ro DateAndTime (SNMPv2-TC) .1.3.6.1.4.1.2696.3.2.1.9.1.1.1.5 |
rfAccuracyCounterResetThe counter object is reset to zero and the counter discontinuity object is set to the current time if 'true' is written to this object. When read, the value of this object is always 'false'.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.2696.3.2.1.9.1.1.1.6 |
rfAccuracyLatestErrorThe timestamp at the most recent occurrence of a threshold error on this measurement.ro DateAndTime (SNMPv2-TC) .1.3.6.1.4.1.2696.3.2.1.9.1.1.1.7 |
rfAccuracyActiveTimeThe total time when it has been possible to perform this measurementro ActiveTime UNITS "second" .1.3.6.1.4.1.2696.3.2.1.9.1.1.1.8 |
rfAccuracyMeasurementStateIndicates the validity of the measurementro MeasurementState .1.3.6.1.4.1.2696.3.2.1.9.1.1.1.9 |
rfAccuracyValueThis is the RF carrier frequency in Hz.ro FloatingPoint UNITS "Hz" .1.3.6.1.4.1.2696.3.2.1.9.1.1.1.10 |
rfChannelWidthTableRF channel width (Sampling Frequency Accuracy) SEQUENCE OF RfChannelWidthEntry .1.3.6.1.4.1.2696.3.2.1.9.1.2 |
rfChannelWidthEntryRow specification RfChannelWidthEntry .1.3.6.1.4.1.2696.3.2.1.9.1.2.1 |
rfChannelWidthInputNumberTransport Stream on which the measurement is made InputNumber .1.3.6.1.4.1.2696.3.2.1.9.1.2.1.1 |
rfChannelWidthTestStateThis indicates whether the rfChannelWidthValue is within the thresholds.ro TestState .1.3.6.1.4.1.2696.3.2.1.9.1.2.1.2 |
rfChannelWidthEnableDetermines whether the threshold test and associated traps for this measurement are enabled.rw Enable .1.3.6.1.4.1.2696.3.2.1.9.1.2.1.3 |
rfChannelWidthCounterCount of the number of times a threshold error has occurred for this measurement.ro Counter32 .1.3.6.1.4.1.2696.3.2.1.9.1.2.1.4 |
rfChannelWidthCounterDiscontinuityProvides the last time at which there was a discontinuity in the counter object.ro DateAndTime (SNMPv2-TC) .1.3.6.1.4.1.2696.3.2.1.9.1.2.1.5 |
rfChannelWidthCounterResetThe counter object is reset to zero and the counter discontinuity object is set to the current time if 'true' is written to this object. When read, the value of this object is always 'false'.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.2696.3.2.1.9.1.2.1.6 |
rfChannelWidthLatestErrorThe timestamp at the most recent occurrence of a threshold error on this measurement.ro DateAndTime (SNMPv2-TC) .1.3.6.1.4.1.2696.3.2.1.9.1.2.1.7 |
rfChannelWidthActiveTimeThe total time when it has been possible to perform this measurementro ActiveTime UNITS "second" .1.3.6.1.4.1.2696.3.2.1.9.1.2.1.8 |
rfChannelWidthMeasurementStateSpecifies the validity of the measurement valuero MeasurementState .1.3.6.1.4.1.2696.3.2.1.9.1.2.1.9 |
rfChannelWidthValueThis is the RF channel width in Hz.ro FloatingPoint UNITS "Hz" .1.3.6.1.4.1.2696.3.2.1.9.1.2.1.10 |
symbolLengthTableSymbol Length measurement at RF (Guard Interval verification) SEQUENCE OF SymbolLengthEntry .1.3.6.1.4.1.2696.3.2.1.9.1.3 |
symbolLengthEntryRow specification SymbolLengthEntry .1.3.6.1.4.1.2696.3.2.1.9.1.3.1 |
symbolLengthInputNumberTransport Stream on which the measurement is made InputNumber .1.3.6.1.4.1.2696.3.2.1.9.1.3.1.1 |
symbolLengthTestStateThis indicates whether the symbolLengthValue is within the thresholds.ro TestState .1.3.6.1.4.1.2696.3.2.1.9.1.3.1.2 |
symbolLengthEnableDetermines whether the threshold test and associated traps for this measurement are enabled.rw Enable .1.3.6.1.4.1.2696.3.2.1.9.1.3.1.3 |
symbolLengthCounterCount of the number of times a threshold error has occurred for this measurement.ro Counter32 .1.3.6.1.4.1.2696.3.2.1.9.1.3.1.4 |
symbolLengthCounterDiscontinuityProvides the last time at which there was a discontinuity in the counter object.ro DateAndTime (SNMPv2-TC) .1.3.6.1.4.1.2696.3.2.1.9.1.3.1.5 |
symbolLengthCounterResetThe counter object is reset to zero and the counter discontinuity object is set to the current time if 'true' is written to this object. When read, the value of this object is always 'false'.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.2696.3.2.1.9.1.3.1.6 |
symbolLengthLatestErrorThe timestamp at the most recent occurrence of a threshold error on this measurement.ro DateAndTime (SNMPv2-TC) .1.3.6.1.4.1.2696.3.2.1.9.1.3.1.7 |
symbolLengthActiveTimeThe total time when it has been possible to perform this measurementro ActiveTime UNITS "second" .1.3.6.1.4.1.2696.3.2.1.9.1.3.1.8 |
symbolLengthMeasurementStateSpecifies the validity of the measurement valuero MeasurementState .1.3.6.1.4.1.2696.3.2.1.9.1.3.1.9 |
symbolLengthValueThis is the symbol length in microseconds.ro FloatingPoint UNITS "microsecond" .1.3.6.1.4.1.2696.3.2.1.9.1.3.1.10 |
rfIfPowerTableRF/IF signal power SEQUENCE OF RfIfPowerEntry .1.3.6.1.4.1.2696.3.2.1.9.5 |
rfIfPowerEntryRow specification RfIfPowerEntry .1.3.6.1.4.1.2696.3.2.1.9.5.1 |
rfIfPowerInputNumberRF input on which the measurement is made InputNumber .1.3.6.1.4.1.2696.3.2.1.9.5.1.1 |
rfIfPowerTestStateThis indicates whether the rfIfPowerValue is within the thresholds.ro TestState .1.3.6.1.4.1.2696.3.2.1.9.5.1.2 |
rfIfPowerEnableDetermines whether the threshold test and associated traps for this measurement are enabled.rw Enable .1.3.6.1.4.1.2696.3.2.1.9.5.1.3 |
rfIfPowerCounterCount of the number of times a threshold error has occurred for this measurement.ro Counter32 .1.3.6.1.4.1.2696.3.2.1.9.5.1.4 |
rfIfPowerCounterDiscontinuityProvides the last time at which there was a discontinuity in the counter object.ro DateAndTime (SNMPv2-TC) .1.3.6.1.4.1.2696.3.2.1.9.5.1.5 |
rfIfPowerCounterResetThe counter object is reset to zero and the counter discontinuity object is set to the current time if 'true' is written to this object. When read, the value of this object is always 'false'.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.2696.3.2.1.9.5.1.6 |
rfIfPowerLatestErrorThe timestamp at the most recent occurrence of a threshold error on this measurement.ro DateAndTime (SNMPv2-TC) .1.3.6.1.4.1.2696.3.2.1.9.5.1.7 |
rfIfPowerActiveTimeThe total time when it has been possible to perform this measurementro ActiveTime UNITS "second" .1.3.6.1.4.1.2696.3.2.1.9.5.1.8 |
rfIfPowerMeasurementStateSpecifies the validity of the measurement valuero MeasurementState .1.3.6.1.4.1.2696.3.2.1.9.5.1.9 |
rfIfPowerValueThe current RF power expressed in dBm, which references 0 dBm as the power of 1 mW.ro FloatingPoint UNITS "dBm" .1.3.6.1.4.1.2696.3.2.1.9.5.1.10 |
rfIfSpectrumTableRF and IF spectrum mask test SEQUENCE OF RfIfSpectrumEntry .1.3.6.1.4.1.2696.3.2.1.9.7 |
rfIfSpectrumEntryRow specification RfIfSpectrumEntry .1.3.6.1.4.1.2696.3.2.1.9.7.1 |
rfIfSpectrumInputNumberTransport Stream on which the measurement is made InputNumber .1.3.6.1.4.1.2696.3.2.1.9.7.1.1 |
rfIfSpectrumTestStateThis indicates whether the signal conforms to the spectrum maskro TestState .1.3.6.1.4.1.2696.3.2.1.9.7.1.2 |
rfIfSpectrumEnableDetermines whether the spectrum mask test and the associated trap are enabled.rw Enable .1.3.6.1.4.1.2696.3.2.1.9.7.1.3 |
rfIfSpectrumCounterCount of the number of times an error has occurred.ro Counter32 .1.3.6.1.4.1.2696.3.2.1.9.7.1.4 |
rfIfSpectrumCounterDiscontinuityProvides the last time at which there was a discontinuity in the counter object.ro DateAndTime (SNMPv2-TC) .1.3.6.1.4.1.2696.3.2.1.9.7.1.5 |
rfIfSpectrumCounterResetThe counter object is reset to zero and the counter discontinuity object is set to the current time if 'true' is written to this object. When read, the value of this object is always 'false'.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.2696.3.2.1.9.7.1.6 |
rfIfSpectrumLatestErrorThe timestamp at the most recent occurrence of an error.ro DateAndTime (SNMPv2-TC) .1.3.6.1.4.1.2696.3.2.1.9.7.1.7 |
rfIfSpectrumActiveTimeThe total time when it has been possible to perform this measurementro ActiveTime UNITS "second" .1.3.6.1.4.1.2696.3.2.1.9.7.1.8 |
eNDT OBJECT IDENTIFIER .1.3.6.1.4.1.2696.3.2.1.9.9 |
eNDTTableEquivalent Noise Degradation measurement. If the DVB-T transmission is hierarchical, this table contains the measurement for the HP (high priority) stream. If the transmission is not hierarchical, this table contains the measurement for the whole stream. SEQUENCE OF ENDTEntry .1.3.6.1.4.1.2696.3.2.1.9.9.1 |
eNDTEntryRow specification ENDTEntry .1.3.6.1.4.1.2696.3.2.1.9.9.1.1 |
eNDTInputNumberTransport Stream on which the measurement is made InputNumber .1.3.6.1.4.1.2696.3.2.1.9.9.1.1.1 |
eNDTTestStateThis indicates whether eNDTValue is within the thresholds.ro TestState .1.3.6.1.4.1.2696.3.2.1.9.9.1.1.2 |
eNDTEnableDetermines whether the threshold test and associated traps for this measurement are enabled.rw Enable .1.3.6.1.4.1.2696.3.2.1.9.9.1.1.3 |
eNDTCounterCount of the number of times a threshold error has occurred for this measurement.ro Counter32 .1.3.6.1.4.1.2696.3.2.1.9.9.1.1.4 |
eNDTCounterDiscontinuityProvides the last time at which there was a discontinuity in the counter object.ro DateAndTime (SNMPv2-TC) .1.3.6.1.4.1.2696.3.2.1.9.9.1.1.5 |
eNDTCounterResetThe counter object is reset to zero and the counter discontinuity object is set to the current time if 'true' is written to this object. When read, the value of this object is always 'false'.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.2696.3.2.1.9.9.1.1.6 |
eNDTLatestErrorThe timestamp at the most recent occurrence of a threshold error on this measurement.ro DateAndTime (SNMPv2-TC) .1.3.6.1.4.1.2696.3.2.1.9.9.1.1.7 |
eNDTActiveTimeThe total time when it has been possible to perform this measurementro ActiveTime UNITS "second" .1.3.6.1.4.1.2696.3.2.1.9.9.1.1.8 |
eNDTMeasurementStateSpecifies the validity of the measurement valuero MeasurementState .1.3.6.1.4.1.2696.3.2.1.9.9.1.1.9 |
eNDTValueThe current Equivalent Noise Degradation expressed in dB.ro FloatingPoint UNITS "dB" .1.3.6.1.4.1.2696.3.2.1.9.9.1.1.10 |
eNFTTableEquivalent Noise Floor measurement. If the DVB-T transmission is hierarchical, this table contains the measurement for the HP (high priority) stream. If the transmission is not hierarchical, this table contains the measurement for the whole stream. SEQUENCE OF ENFTEntry .1.3.6.1.4.1.2696.3.2.1.9.9.2 |
eNFTEntryRow specification ENFTEntry .1.3.6.1.4.1.2696.3.2.1.9.9.2.1 |
eNFTInputNumberTransport Stream on which the measurement is made InputNumber .1.3.6.1.4.1.2696.3.2.1.9.9.2.1.1 |
eNFTTestStateThis indicates whether the eNFTValue is within the thresholds.ro TestState .1.3.6.1.4.1.2696.3.2.1.9.9.2.1.2 |
eNFTEnableDetermines whether the threshold test and associated traps for this measurement are enabled.rw Enable .1.3.6.1.4.1.2696.3.2.1.9.9.2.1.3 |
eNFTCounterCount of the number of times a threshold error has occurred for this measurement.ro Counter32 .1.3.6.1.4.1.2696.3.2.1.9.9.2.1.4 |
eNFTCounterDiscontinuityProvides the last time at which there was a discontinuity in the counter object.ro DateAndTime (SNMPv2-TC) .1.3.6.1.4.1.2696.3.2.1.9.9.2.1.5 |
eNFTCounterResetThe counter object is reset to zero and the counter discontinuity object is set to the current time if 'true' is written to this object. When read, the value of this object is always 'false'.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.2696.3.2.1.9.9.2.1.6 |
eNFTLatestErrorThe timestamp at the most recent occurrence of a threshold error on this measurement.ro DateAndTime (SNMPv2-TC) .1.3.6.1.4.1.2696.3.2.1.9.9.2.1.7 |
eNFTActiveTimeThe total time when it has been possible to perform this measurementro ActiveTime UNITS "second" .1.3.6.1.4.1.2696.3.2.1.9.9.2.1.8 |
eNFTMeasurementStateSpecifies the validity of the measurement valuero MeasurementState .1.3.6.1.4.1.2696.3.2.1.9.9.2.1.9 |
eNFTValueThe current Equivalent Noise Floor expressed in dB, see the reference for the method of calculation.ro FloatingPoint UNITS "dB" .1.3.6.1.4.1.2696.3.2.1.9.9.2.1.10 |
eNDTLPTableEquivalent Noise Degradation measurement. If the DVB-T transmission is hierarchical, this table contains the measurement for the LP (low priority) stream. If the transmission is not hierarchical, the MeasurementState for this table will be 'unknown'. SEQUENCE OF ENDTLPEntry .1.3.6.1.4.1.2696.3.2.1.9.9.3 |
eNDTLPEntryRow specification ENDTLPEntry .1.3.6.1.4.1.2696.3.2.1.9.9.3.1 |
eNDTLPInputNumberTransport Stream on which the measurement is made InputNumber .1.3.6.1.4.1.2696.3.2.1.9.9.3.1.1 |
eNDTLPTestStateThis indicates whether eNDTLPValue is within the thresholds.ro TestState .1.3.6.1.4.1.2696.3.2.1.9.9.3.1.2 |
eNDTLPEnableDetermines whether the threshold test and associated traps for this measurement are enabled.rw Enable .1.3.6.1.4.1.2696.3.2.1.9.9.3.1.3 |
eNDTLPCounterCount of the number of times a threshold error has occurred for this measurement.ro Counter32 .1.3.6.1.4.1.2696.3.2.1.9.9.3.1.4 |
eNDTLPCounterDiscontinuityProvides the last time at which there was a discontinuity in the counter object.ro DateAndTime (SNMPv2-TC) .1.3.6.1.4.1.2696.3.2.1.9.9.3.1.5 |
eNDTLPCounterResetThe counter object is reset to zero and the counter discontinuity object is set to the current time if 'true' is written to this object. When read, the value of this object is always 'false'.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.2696.3.2.1.9.9.3.1.6 |
eNDTLPLatestErrorThe timestamp at the most recent occurrence of a threshold error on this measurement.ro DateAndTime (SNMPv2-TC) .1.3.6.1.4.1.2696.3.2.1.9.9.3.1.7 |
eNDTLPActiveTimeThe total time when it has been possible to perform this measurementro ActiveTime .1.3.6.1.4.1.2696.3.2.1.9.9.3.1.8 |
eNDTLPMeasurementStateSpecifies the validity of the measurement valuero MeasurementState .1.3.6.1.4.1.2696.3.2.1.9.9.3.1.9 |
eNDTLPValueThe current Equivalent Noise Degradation for the low priority stream expressed in dB.ro FloatingPoint UNITS "dB" .1.3.6.1.4.1.2696.3.2.1.9.9.3.1.10 |
eNFTLPTableEquivalent Noise Floor measurement. If the DVB-T transmission is hierarchical, this table contains the measurement for the LP (low priority) stream. If the transmission is not hierarchical, the MeasurementState for this table will be 'unknown'. SEQUENCE OF ENFTLPEntry .1.3.6.1.4.1.2696.3.2.1.9.9.4 |
eNFTLPEntryRow specification ENFTLPEntry .1.3.6.1.4.1.2696.3.2.1.9.9.4.1 |
eNFTLPInputNumberTransport Stream on which the measurement is made InputNumber .1.3.6.1.4.1.2696.3.2.1.9.9.4.1.1 |
eNFTLPTestStateThis indicates whether eNFTLPValue is within the thresholds.ro TestState .1.3.6.1.4.1.2696.3.2.1.9.9.4.1.2 |
eNFTLPEnableDetermines whether the threshold test and associated traps for this measurement are enabled.rw Enable .1.3.6.1.4.1.2696.3.2.1.9.9.4.1.3 |
eNFTLPCounterCount of the number of times a threshold error has occurred for this measurement.ro Counter32 .1.3.6.1.4.1.2696.3.2.1.9.9.4.1.4 |
eNFTLPCounterDiscontinuityProvides the last time at which there was a discontinuity in the counter object.ro DateAndTime (SNMPv2-TC) .1.3.6.1.4.1.2696.3.2.1.9.9.4.1.5 |
eNFTLPCounterResetThe counter object is reset to zero and the counter discontinuity object is set to the current time if 'true' is written to this object. When read, the value of this object is always 'false'.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.2696.3.2.1.9.9.4.1.6 |
eNFTLPLatestErrorThe timestamp at the most recent occurrence of a threshold error on this measurement.ro DateAndTime (SNMPv2-TC) .1.3.6.1.4.1.2696.3.2.1.9.9.4.1.7 |
eNFTLPActiveTimeThe total time when it has been possible to perform this measurementro ActiveTime .1.3.6.1.4.1.2696.3.2.1.9.9.4.1.8 |
eNFTLPMeasurementStateSpecifies the validity of the measurement valuero MeasurementState .1.3.6.1.4.1.2696.3.2.1.9.9.4.1.9 |
eNFTLPValueThe current Equivalent Noise Floor for the low priority stream, expressed in dB, see the reference for the method of calculation.ro FloatingPoint UNITS "dB" .1.3.6.1.4.1.2696.3.2.1.9.9.4.1.10 |
linearityTableLinearity characterization (shoulder attenuation) SEQUENCE OF LinearityEntry .1.3.6.1.4.1.2696.3.2.1.9.10 |
linearityEntryRow specification LinearityEntry .1.3.6.1.4.1.2696.3.2.1.9.10.1 |
linearityInputNumberTransport Stream on which the measurement is made InputNumber .1.3.6.1.4.1.2696.3.2.1.9.10.1.1 |
linearityTestStateThis indicates whether the linearityValue is above the minimum permitted.ro TestState .1.3.6.1.4.1.2696.3.2.1.9.10.1.2 |
linearityEnableDetermines whether the threshold test and associated traps for this measurement are enabled.rw Enable .1.3.6.1.4.1.2696.3.2.1.9.10.1.3 |
linearityCounterCount of the number of times a threshold error has occurred for this measurement.ro Counter32 .1.3.6.1.4.1.2696.3.2.1.9.10.1.4 |
linearityCounterDiscontinuityProvides the last time at which there was a discontinuity in the counter object.ro DateAndTime (SNMPv2-TC) .1.3.6.1.4.1.2696.3.2.1.9.10.1.5 |
linearityCounterResetThe counter object is reset to zero and the counter discontinuity object is set to the current time if 'true' is written to this object. When read, the value of this object is always 'false'.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.2696.3.2.1.9.10.1.6 |
linearityLatestErrorThe timestamp at the most recent occurrence of a threshold error on this measurement.ro DateAndTime (SNMPv2-TC) .1.3.6.1.4.1.2696.3.2.1.9.10.1.7 |
linearityActiveTimeThe total time when it has been possible to perform this measurementro ActiveTime UNITS "second" .1.3.6.1.4.1.2696.3.2.1.9.10.1.8 |
linearityMeasurementStateSpecifies the validity of the measurement valuero MeasurementState .1.3.6.1.4.1.2696.3.2.1.9.10.1.9 |
linearityValueThe current linearity (shoulder attenuation) expressed in dB.ro FloatingPoint UNITS "dB" .1.3.6.1.4.1.2696.3.2.1.9.10.1.10 |
berViterbiT OBJECT IDENTIFIER .1.3.6.1.4.1.2696.3.2.1.9.15 |
berViterbiTTableBER before Viterbi measurement. If the DVB-T transmission is hierarchical, this table contains the measurement for the HP (high priority) stream. If the transmission is not hierarchical, this table contains the measurement for the whole stream. SEQUENCE OF BerViterbiTEntry .1.3.6.1.4.1.2696.3.2.1.9.15.1 |
berViterbiTEntryRow specification BerViterbiTEntry .1.3.6.1.4.1.2696.3.2.1.9.15.1.1 |
berViterbiTInputNumberTransport Stream on which the measurement is made InputNumber .1.3.6.1.4.1.2696.3.2.1.9.15.1.1.1 |
berViterbiTTestStateThis indicates whether the berViterbiTValue is within the thresholds.ro TestState .1.3.6.1.4.1.2696.3.2.1.9.15.1.1.2 |
berViterbiTEnableDetermines whether the threshold test and associated traps for this measurement are enabled.rw Enable .1.3.6.1.4.1.2696.3.2.1.9.15.1.1.3 |
berViterbiTCounterCount of the number of times a threshold error has occurred for this measurement.ro Counter32 .1.3.6.1.4.1.2696.3.2.1.9.15.1.1.4 |
berViterbiTCounterDiscontinuityProvides the last time at which there was a discontinuity in the counter object.ro DateAndTime (SNMPv2-TC) .1.3.6.1.4.1.2696.3.2.1.9.15.1.1.5 |
berViterbiTCounterResetThe counter object is reset to zero and the counter discontinuity object is set to the current time if 'true' is written to this object. When read, the value of this object is always 'false'.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.2696.3.2.1.9.15.1.1.6 |
berViterbiTLatestErrorThe timestamp at the most recent occurrence of a threshold error on this measurement.ro DateAndTime (SNMPv2-TC) .1.3.6.1.4.1.2696.3.2.1.9.15.1.1.7 |
berViterbiTActiveTimeThe total time when it has been possible to perform this measurementro ActiveTime .1.3.6.1.4.1.2696.3.2.1.9.15.1.1.8 |
berViterbiTMeasurementStateSpecifies the validity of the measurement valuero MeasurementState .1.3.6.1.4.1.2696.3.2.1.9.15.1.1.9 |
berViterbiTValueThis is the overall pre-Viterbi BER value, for example 0.0000046ro FloatingPoint .1.3.6.1.4.1.2696.3.2.1.9.15.1.1.10 |
berViterbiTLPTableBER before Viterbi measurement. If the DVB-T transmission is hierarchical, this table contains the measurement for the LP (low priority) stream. If the transmission is not hierarchical, the MeasurementState for this table will be 'unknown'. SEQUENCE OF BerViterbiTLPEntry .1.3.6.1.4.1.2696.3.2.1.9.15.2 |
berViterbiTLPEntryRow specification BerViterbiTLPEntry .1.3.6.1.4.1.2696.3.2.1.9.15.2.1 |
berViterbiTLPInputNumberTransport Stream on which the measurement is made InputNumber .1.3.6.1.4.1.2696.3.2.1.9.15.2.1.1 |
berViterbiTLPTestStateThis indicates whether the berViterbiTLPValue is within the thresholds.ro TestState .1.3.6.1.4.1.2696.3.2.1.9.15.2.1.2 |
berViterbiTLPEnableDetermines whether the threshold test and associated traps for this measurement are enabled.rw Enable .1.3.6.1.4.1.2696.3.2.1.9.15.2.1.3 |
berViterbiTLPCounterCount of the number of times a threshold error has occurred for this measurement.ro Counter32 .1.3.6.1.4.1.2696.3.2.1.9.15.2.1.4 |
berViterbiTLPCounterDiscontinuityProvides the last time at which there was a discontinuity in the counter object.ro DateAndTime (SNMPv2-TC) .1.3.6.1.4.1.2696.3.2.1.9.15.2.1.5 |
berViterbiTLPCounterResetThe counter object is reset to zero and the counter discontinuity object is set to the current time if 'true' is written to this object. When read, the value of this object is always 'false'.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.2696.3.2.1.9.15.2.1.6 |
berViterbiTLPLatestErrorThe timestamp at the most recent occurrence of a threshold error on this measurement.ro DateAndTime (SNMPv2-TC) .1.3.6.1.4.1.2696.3.2.1.9.15.2.1.7 |
berViterbiTLPActiveTimeThe total time when it has been possible to perform this measurementro ActiveTime .1.3.6.1.4.1.2696.3.2.1.9.15.2.1.8 |
berViterbiTLPMeasurementStateSpecifies the validity of the measurement valuero MeasurementState .1.3.6.1.4.1.2696.3.2.1.9.15.2.1.9 |
berViterbiTLPValueThis is the overall pre-Viterbi BER value, for example 0.0000046ro FloatingPoint UNITS "dB" .1.3.6.1.4.1.2696.3.2.1.9.15.2.1.10 |
berRS OBJECT IDENTIFIER .1.3.6.1.4.1.2696.3.2.1.9.16 |
berRSTableBER before RS measurement. If the DVB-T transmission is hierarchical, this table contains the measurement for the HP (high priority) stream. If the transmission is not hierarchical, this table contains the measurement for the whole stream. SEQUENCE OF BerRSEntry .1.3.6.1.4.1.2696.3.2.1.9.16.1 |
berRSEntryRow specification BerRSEntry .1.3.6.1.4.1.2696.3.2.1.9.16.1.1 |
berRSInputNumberTransport Stream on which the measurement is made InputNumber .1.3.6.1.4.1.2696.3.2.1.9.16.1.1.1 |
berRSTestStateThis indicates whether berRSValue is below the maximum.ro TestState .1.3.6.1.4.1.2696.3.2.1.9.16.1.1.2 |
berRSEnableDetermines whether the threshold test and associated traps for this measurement are enabled.rw Enable .1.3.6.1.4.1.2696.3.2.1.9.16.1.1.3 |
berRSCounterCount of the number of times a threshold error has occurred for this measurement.ro Counter32 .1.3.6.1.4.1.2696.3.2.1.9.16.1.1.4 |
berRSCounterDiscontinuityProvides the last time at which there was a discontinuity in the counter object.ro DateAndTime (SNMPv2-TC) .1.3.6.1.4.1.2696.3.2.1.9.16.1.1.5 |
berRSCounterResetThe counter object is reset to zero and the counter discontinuity object is set to the current time if 'true' is written to this object. When read, the value of this object is always 'false'.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.2696.3.2.1.9.16.1.1.6 |
berRSLatestErrorThe timestamp at the most recent occurrence of a threshold error on this measurement.ro DateAndTime (SNMPv2-TC) .1.3.6.1.4.1.2696.3.2.1.9.16.1.1.7 |
berRSActiveTimeThe total time when it has been possible to perform this measurementro ActiveTime .1.3.6.1.4.1.2696.3.2.1.9.16.1.1.8 |
berRSMeasurementStateSpecifies the validity of the measurement valuero MeasurementState .1.3.6.1.4.1.2696.3.2.1.9.16.1.1.9 |
berRSValueThis is the BER before RS (outer) decoder measured using the in-service method. It is expressed as a number, e.g. 0.0000034ro FloatingPoint .1.3.6.1.4.1.2696.3.2.1.9.16.1.1.10 |
berRSLPTableBER before RS measurement. If the DVB-T transmission is hierarchical, this table contains the measurement for the LP (low priority) stream. If the transmission is not hierarchical, the MeasurementState for this table will be 'unknown'. SEQUENCE OF BerRSLPEntry .1.3.6.1.4.1.2696.3.2.1.9.16.2 |
berRSLPEntryRow specification BerRSLPEntry .1.3.6.1.4.1.2696.3.2.1.9.16.2.1 |
berRSLPInputNumberTransport Stream on which the measurement is made InputNumber .1.3.6.1.4.1.2696.3.2.1.9.16.2.1.1 |
berRSLPTestStateThis indicates whether berRSLPValue is within the thresholds.ro TestState .1.3.6.1.4.1.2696.3.2.1.9.16.2.1.2 |
berRSLPEnableDetermines whether the threshold test and associated traps for this measurement are enabled.rw Enable .1.3.6.1.4.1.2696.3.2.1.9.16.2.1.3 |
berRSLPCounterCount of the number of times a threshold error has occurred for this measurement.ro Counter32 .1.3.6.1.4.1.2696.3.2.1.9.16.2.1.4 |
berRSLPCounterDiscontinuityProvides the last time at which there was a discontinuity in the counter object.ro DateAndTime (SNMPv2-TC) .1.3.6.1.4.1.2696.3.2.1.9.16.2.1.5 |
berRSLPCounterResetThe counter object is reset to zero and the counter discontinuity object is set to the current time if 'true' is written to this object. When read, the value of this object is always 'false'.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.2696.3.2.1.9.16.2.1.6 |
berRSLPLatestErrorThe timestamp at the most recent occurrence of a threshold error on this measurement.ro DateAndTime (SNMPv2-TC) .1.3.6.1.4.1.2696.3.2.1.9.16.2.1.7 |
berRSLPActiveTimeThe total time when it has been possible to perform this measurementro ActiveTime .1.3.6.1.4.1.2696.3.2.1.9.16.2.1.8 |
berRSLPMeasurementStateSpecifies the validity of the measurement valuero MeasurementState .1.3.6.1.4.1.2696.3.2.1.9.16.2.1.9 |
berRSLPValueThis is the BER before RS (outer) decoder for the low priority stream measured using the in-service method. It is expressed as a number, e.g. 0.0000034ro FloatingPoint .1.3.6.1.4.1.2696.3.2.1.9.16.2.1.10 |
iqAnalysisT OBJECT IDENTIFIER .1.3.6.1.4.1.2696.3.2.1.9.18 |
merTTableModulation Error Ratio (MER) measurement SEQUENCE OF MerTEntry .1.3.6.1.4.1.2696.3.2.1.9.18.2 |
merTEntryRow specification MerTEntry .1.3.6.1.4.1.2696.3.2.1.9.18.2.1 |
merTInputNumberTransport Stream on which the measurement is made InputNumber .1.3.6.1.4.1.2696.3.2.1.9.18.2.1.1 |
merTTestStateThis indicates whether merTValue is within the thresholds.ro TestState .1.3.6.1.4.1.2696.3.2.1.9.18.2.1.2 |
merTEnableDetermines whether the threshold test and associated traps for this measurement are enabled.rw Enable .1.3.6.1.4.1.2696.3.2.1.9.18.2.1.3 |
merTCounterCount of the number of times a threshold error has occurred for this measurement.ro Counter32 .1.3.6.1.4.1.2696.3.2.1.9.18.2.1.4 |
merTCounterDiscontinuityProvides the last time at which there was a discontinuity in the merTCounter object.ro DateAndTime (SNMPv2-TC) .1.3.6.1.4.1.2696.3.2.1.9.18.2.1.5 |
merTCounterResetThe counter object is reset to zero and the counter discontinuity object is set to the current time if 'true' is written to this object. When read, the value of this object is always 'false'.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.2696.3.2.1.9.18.2.1.6 |
merTLatestErrorThe timestamp at the most recent occurrence of a threshold error on this measurement.ro DateAndTime (SNMPv2-TC) .1.3.6.1.4.1.2696.3.2.1.9.18.2.1.7 |
merTActiveTimeThe total time when it has been possible to perform this measurementro ActiveTime UNITS "second" .1.3.6.1.4.1.2696.3.2.1.9.18.2.1.8 |
merTMeasurementStateSpecifies the validity of the measurement valuero MeasurementState .1.3.6.1.4.1.2696.3.2.1.9.18.2.1.9 |
merTValueThe current Modulation Error Ratio expressed in dBro FloatingPoint UNITS "dB" .1.3.6.1.4.1.2696.3.2.1.9.18.2.1.10 |
steT OBJECT IDENTIFIER .1.3.6.1.4.1.2696.3.2.1.9.18.3 |
steMeanTTableSystem Target Error Mean (STEM) measurement SEQUENCE OF SteMeanTEntry .1.3.6.1.4.1.2696.3.2.1.9.18.3.1 |
steMeanTEntryRow specification SteMeanTEntry .1.3.6.1.4.1.2696.3.2.1.9.18.3.1.1 |
steMeanTInputNumberTransport Stream on which the measurement is made InputNumber .1.3.6.1.4.1.2696.3.2.1.9.18.3.1.1.1 |
steMeanTTestStateThis indicates whether steMeanTValue is currently within the thresholds.ro TestState .1.3.6.1.4.1.2696.3.2.1.9.18.3.1.1.2 |
steMeanTEnableDetermines whether the threshold test and associated traps for this measurement are enabled.rw Enable .1.3.6.1.4.1.2696.3.2.1.9.18.3.1.1.3 |
steMeanTCounterCount of the number of times a threshold error has occurred for this measurement.ro Counter32 .1.3.6.1.4.1.2696.3.2.1.9.18.3.1.1.4 |
steMeanTCounterDiscontinuityProvides the last time at which there was a discontinuity in the counter object.ro DateAndTime (SNMPv2-TC) .1.3.6.1.4.1.2696.3.2.1.9.18.3.1.1.5 |
steMeanTCounterResetThe counter object is reset to zero and the counter discontinuity object is set to the current time if 'true' is written to this object. When read, the value of this object is always 'false'.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.2696.3.2.1.9.18.3.1.1.6 |
steMeanTLatestErrorThe timestamp at the most recent occurrence of a threshold error on this measurement.ro DateAndTime (SNMPv2-TC) .1.3.6.1.4.1.2696.3.2.1.9.18.3.1.1.7 |
steMeanTActiveTimeThe total time when it has been possible to perform this measurementro ActiveTime UNITS "second" .1.3.6.1.4.1.2696.3.2.1.9.18.3.1.1.8 |
steMeanTMeasurementStateSpecifies the validity of the measurement valuero MeasurementState .1.3.6.1.4.1.2696.3.2.1.9.18.3.1.1.9 |
steMeanTValueThe current System Target Error Mean as a numeric valuero FloatingPoint .1.3.6.1.4.1.2696.3.2.1.9.18.3.1.1.10 |
steDeviationTTableSystem Target Error Deviation (STED) measurement SEQUENCE OF SteDeviationTEntry .1.3.6.1.4.1.2696.3.2.1.9.18.3.2 |
steDeviationTEntryRow specification SteDeviationTEntry .1.3.6.1.4.1.2696.3.2.1.9.18.3.2.1 |
steDeviationTInputNumberTransport Stream on which the measurement is made InputNumber .1.3.6.1.4.1.2696.3.2.1.9.18.3.2.1.1 |
steDeviationTTestStateThis indicates whether steDeviationTValue is currently within the thresholds.ro TestState .1.3.6.1.4.1.2696.3.2.1.9.18.3.2.1.2 |
steDeviationTEnableDetermines whether the threshold test and associated traps for this measurement are enabled.rw Enable .1.3.6.1.4.1.2696.3.2.1.9.18.3.2.1.3 |
steDeviationTCounterCount of the number of times a threshold error has occurred for this measurement.ro Counter32 .1.3.6.1.4.1.2696.3.2.1.9.18.3.2.1.4 |
steDeviationTCounterDiscontinuityProvides the last time at which there was a discontinuity in the counter object.ro DateAndTime (SNMPv2-TC) .1.3.6.1.4.1.2696.3.2.1.9.18.3.2.1.5 |
steDeviationTCounterResetThe counter object is reset to zero and the counter discontinuity object is set to the current time if 'true' is written to this object. When read, the value of this object is always 'false'.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.2696.3.2.1.9.18.3.2.1.6 |
steDeviationTLatestErrorThe timestamp at the most recent occurrence of a threshold error on this measurement.ro DateAndTime (SNMPv2-TC) .1.3.6.1.4.1.2696.3.2.1.9.18.3.2.1.7 |
steDeviationTActiveTimeThe total time when it has been possible to perform this measurementro ActiveTime UNITS "second" .1.3.6.1.4.1.2696.3.2.1.9.18.3.2.1.8 |
steDeviationTMeasurementStateSpecifies the validity of the measurement valuero MeasurementState .1.3.6.1.4.1.2696.3.2.1.9.18.3.2.1.9 |
steDeviationTValueThe current System Target Error Deviation as a numeric valuero FloatingPoint .1.3.6.1.4.1.2696.3.2.1.9.18.3.2.1.10 |
csTTableCarrier Suppression (CS) measurement SEQUENCE OF CsTEntry .1.3.6.1.4.1.2696.3.2.1.9.18.4 |
csTEntryRow specification CsTEntry .1.3.6.1.4.1.2696.3.2.1.9.18.4.1 |
csTInputNumberTransport Stream on which the measurement is made InputNumber .1.3.6.1.4.1.2696.3.2.1.9.18.4.1.1 |
csTTestStateThis indicates whether csTValue is currently within the thresholds.ro TestState .1.3.6.1.4.1.2696.3.2.1.9.18.4.1.2 |
csTEnableDetermines whether the threshold test and associated traps for this measurement are enabled.rw Enable .1.3.6.1.4.1.2696.3.2.1.9.18.4.1.3 |
csTCounterCount of the number of times a threshold error has occurred for this measurement.ro Counter32 .1.3.6.1.4.1.2696.3.2.1.9.18.4.1.4 |
csTCounterDiscontinuityProvides the last time at which there was a discontinuity in the counter object.ro DateAndTime (SNMPv2-TC) .1.3.6.1.4.1.2696.3.2.1.9.18.4.1.5 |
csTCounterResetThe counter object is reset to zero and the counter discontinuity object is set to the current time if 'true' is written to this object. When read, the value of this object is always 'false'.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.2696.3.2.1.9.18.4.1.6 |
csTLatestErrorThe timestamp at the most recent occurrence of a threshold error on this measurement.ro DateAndTime (SNMPv2-TC) .1.3.6.1.4.1.2696.3.2.1.9.18.4.1.7 |
csTActiveTimeThe total time when it has been possible to perform this measurementro ActiveTime UNITS "second" .1.3.6.1.4.1.2696.3.2.1.9.18.4.1.8 |
csTMeasurementStateSpecifies the validity of the measurement valuero MeasurementState .1.3.6.1.4.1.2696.3.2.1.9.18.4.1.9 |
csTValueThe current Carrier Suppression value in dB.ro FloatingPoint UNITS "dB" .1.3.6.1.4.1.2696.3.2.1.9.18.4.1.10 |
aiTTableAmplitude Imbalance (AI) measurement SEQUENCE OF AiTEntry .1.3.6.1.4.1.2696.3.2.1.9.18.5 |
aiTEntryRow specification AiTEntry .1.3.6.1.4.1.2696.3.2.1.9.18.5.1 |
aiTInputNumberTransport Stream on which the measurement is made InputNumber .1.3.6.1.4.1.2696.3.2.1.9.18.5.1.1 |
aiTTestStateThis indicates whether aiTValue is currently within the thresholds.ro TestState .1.3.6.1.4.1.2696.3.2.1.9.18.5.1.2 |
aiTEnableDetermines whether the threshold test and associated traps for this measurement are enabled.rw Enable .1.3.6.1.4.1.2696.3.2.1.9.18.5.1.3 |
aiTCounterCount of the number of times a threshold error has occurred for this measurement.ro Counter32 .1.3.6.1.4.1.2696.3.2.1.9.18.5.1.4 |
aiTCounterDiscontinuityProvides the last time at which there was a discontinuity in the counter object.ro DateAndTime (SNMPv2-TC) .1.3.6.1.4.1.2696.3.2.1.9.18.5.1.5 |
aiTCounterResetThe counter object is reset to zero and the counter discontinuity object is set to the current time if 'true' is written to this object. When read, the value of this object is always 'false'.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.2696.3.2.1.9.18.5.1.6 |
aiTLatestErrorThe timestamp at the most recent occurrence of a threshold error on this measurement.ro DateAndTime (SNMPv2-TC) .1.3.6.1.4.1.2696.3.2.1.9.18.5.1.7 |
aiTActiveTimeThe total time when it has been possible to perform this measurementro ActiveTime UNITS "second" .1.3.6.1.4.1.2696.3.2.1.9.18.5.1.8 |
aiTMeasurementStateSpecifies the validity of the measurement valuero MeasurementState .1.3.6.1.4.1.2696.3.2.1.9.18.5.1.9 |
aiTValueThe current Amplitude Imbalance as a percentagero FloatingPoint .1.3.6.1.4.1.2696.3.2.1.9.18.5.1.10 |
qeTTableQuadrature Error (QE) measurement SEQUENCE OF QeTEntry .1.3.6.1.4.1.2696.3.2.1.9.18.6 |
qeTEntryRow specification QeTEntry .1.3.6.1.4.1.2696.3.2.1.9.18.6.1 |
qeTInputNumberTransport Stream on which the measurement is made InputNumber .1.3.6.1.4.1.2696.3.2.1.9.18.6.1.1 |
qeTTestStateThis indicates whether qeTValue is currently within the thresholds.ro TestState .1.3.6.1.4.1.2696.3.2.1.9.18.6.1.2 |
qeTEnableDetermines whether the threshold test and associated traps for this measurement are enabled.rw Enable .1.3.6.1.4.1.2696.3.2.1.9.18.6.1.3 |
qeTCounterCount of the number of times a threshold error has occurred for this measurement.ro Counter32 .1.3.6.1.4.1.2696.3.2.1.9.18.6.1.4 |
qeTCounterDiscontinuityProvides the last time at which there was a discontinuity in the counter object.ro DateAndTime (SNMPv2-TC) .1.3.6.1.4.1.2696.3.2.1.9.18.6.1.5 |
qeTCounterResetThe counter object is reset to zero and the counter discontinuity object is set to the current time if 'true' is written to this object. When read, the value of this object is always 'false'.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.2696.3.2.1.9.18.6.1.6 |
qeTLatestErrorThe timestamp at the most recent occurrence of a threshold error on this measurement.ro DateAndTime (SNMPv2-TC) .1.3.6.1.4.1.2696.3.2.1.9.18.6.1.7 |
qeTActiveTimeThe total time when it has been possible to perform this measurementro ActiveTime UNITS "second" .1.3.6.1.4.1.2696.3.2.1.9.18.6.1.8 |
qeTMeasurementStateSpecifies the validity of the measurement valuero MeasurementState .1.3.6.1.4.1.2696.3.2.1.9.18.6.1.9 |
qeTValueThe current Quadrature Error value in degrees.ro FloatingPoint UNITS "degree" .1.3.6.1.4.1.2696.3.2.1.9.18.6.1.10 |
pjTTablePhase Jitter (PJ) measurement SEQUENCE OF PjTEntry .1.3.6.1.4.1.2696.3.2.1.9.18.7 |
pjTEntryRow specification PjTEntry .1.3.6.1.4.1.2696.3.2.1.9.18.7.1 |
pjTInputNumberTransport Stream on which the measurement is made InputNumber .1.3.6.1.4.1.2696.3.2.1.9.18.7.1.1 |
pjTTestStateThis indicates whether pjTValue is currently within the thresholds.ro TestState .1.3.6.1.4.1.2696.3.2.1.9.18.7.1.2 |
pjTEnableDetermines whether the threshold test and associated traps for this measurement are enabled.rw Enable .1.3.6.1.4.1.2696.3.2.1.9.18.7.1.3 |
pjTCounterCount of the number of times a threshold error has occurred for this measurement.ro Counter32 .1.3.6.1.4.1.2696.3.2.1.9.18.7.1.4 |
pjTCounterDiscontinuityProvides the last time at which there was a discontinuity in the counter object.ro DateAndTime (SNMPv2-TC) .1.3.6.1.4.1.2696.3.2.1.9.18.7.1.5 |
pjTCounterResetThe counter object is reset to zero and the counter discontinuity object is set to the current time if 'true' is written to this object. When read, the value of this object is always 'false'.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.2696.3.2.1.9.18.7.1.6 |
pjTLatestErrorThe timestamp at the most recent occurrence of a threshold error on this measurement.ro DateAndTime (SNMPv2-TC) .1.3.6.1.4.1.2696.3.2.1.9.18.7.1.7 |
pjTActiveTimeThe total time when it has been possible to perform this measurementro ActiveTime UNITS "second" .1.3.6.1.4.1.2696.3.2.1.9.18.7.1.8 |
pjTMeasurementStateSpecifies the validity of the measurement valuero MeasurementState .1.3.6.1.4.1.2696.3.2.1.9.18.7.1.9 |
pjTValueThe current Phase Jitter value in degrees.ro FloatingPoint UNITS "degree" .1.3.6.1.4.1.2696.3.2.1.9.18.7.1.10 |
mipSyntaxTableSFN MIP baseband tests SEQUENCE OF MipSyntaxEntry .1.3.6.1.4.1.2696.3.2.1.9.20 |
mipSyntaxEntryRow specification MipSyntaxEntry .1.3.6.1.4.1.2696.3.2.1.9.20.1 |
mipSyntaxInputNumberTransport Stream on which the measurement is made InputNumber .1.3.6.1.4.1.2696.3.2.1.9.20.1.1 |
mipSyntaxTestNumberThe specific SFN MIP test that this row applies to IndexMIPSyntaxTest .1.3.6.1.4.1.2696.3.2.1.9.20.1.2 |
mipSyntaxStateThis gives the overall pass/fail state of the test.ro TestState .1.3.6.1.4.1.2696.3.2.1.9.20.1.3 |
mipSyntaxEnableDetermines whether this test and the associated trap are enabled.rw Enable .1.3.6.1.4.1.2696.3.2.1.9.20.1.4 |
mipSyntaxCounterCount of the number of times this error has occurredro Counter32 .1.3.6.1.4.1.2696.3.2.1.9.20.1.5 |
mipSyntaxCounterDiscontinuityProvides the last time at which there was a discontinuity in the mipSyntaxCounter object.ro DateAndTime (SNMPv2-TC) .1.3.6.1.4.1.2696.3.2.1.9.20.1.6 |
mipSyntaxCounterResetThe counter object is reset to zero and the counter discontinuity object is set to the current time if 'true' is written to this object. When read, the value of this object is always 'false'.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.2696.3.2.1.9.20.1.7 |
mipSyntaxLatestErrorThe timestamp at the most recent occurrence of the errorro DateAndTime (SNMPv2-TC) .1.3.6.1.4.1.2696.3.2.1.9.20.1.8 |
mipSyntaxActiveTimeThe total time when it has been possible to perform this measurementro ActiveTime UNITS "second" .1.3.6.1.4.1.2696.3.2.1.9.20.1.9 |
systemErrorPerformance OBJECT IDENTIFIER .1.3.6.1.4.1.2696.3.2.1.9.21 |
sepEtiTableMeasurement of Errored Second Ratio (ESR) or Errored Time Interval Ratio (ETIR). SEQUENCE OF SepEtiEntry .1.3.6.1.4.1.2696.3.2.1.9.21.1 |
sepEtiEntryRow specification SepEtiEntry .1.3.6.1.4.1.2696.3.2.1.9.21.1.1 |
sepEtiInputNumberTransport Stream on which the measurement is made InputNumber .1.3.6.1.4.1.2696.3.2.1.9.21.1.1.1 |
sepEtiTestStateA 'fail' indicaties that the most recently completed time interval TI was an Errored Time Interval (ETI). A 'pass' indicates that the most recent TI was not errored.ro TestState .1.3.6.1.4.1.2696.3.2.1.9.21.1.1.2 |
sepEtiEnableDetermines whether the threshold test and associated traps for this measurement are enabled.rw Enable .1.3.6.1.4.1.2696.3.2.1.9.21.1.1.3 |
sepEtiCounterCount of the number of times an ETI has occurred.ro Counter32 .1.3.6.1.4.1.2696.3.2.1.9.21.1.1.4 |
sepEtiCounterDiscontinuityProvides the last time at which there was a discontinuity in the counter object.ro DateAndTime (SNMPv2-TC) .1.3.6.1.4.1.2696.3.2.1.9.21.1.1.5 |
sepEtiCounterResetThe counter object is reset to zero and the counter discontinuity object is set to the current time if 'true' is written to this object. When read, the value of this object is always 'false'.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.2696.3.2.1.9.21.1.1.6 |
sepEtiLatestErrorThe timestamp at the most recent occurrence of an ETI.ro DateAndTime (SNMPv2-TC) .1.3.6.1.4.1.2696.3.2.1.9.21.1.1.7 |
sepEtiActiveTimeThe total time when it has been possible to perform this measurementro ActiveTime UNITS "second" .1.3.6.1.4.1.2696.3.2.1.9.21.1.1.8 |
sepEtiMeasurementStateSpecifies the validity of the measurement valuero MeasurementState .1.3.6.1.4.1.2696.3.2.1.9.21.1.1.9 |
sepEtiValueThis is the Errored Time Interval Ratio (ETIR) for the most recently completed Measurement Interval (MI). It is expressed as a numeric value.ro FloatingPoint .1.3.6.1.4.1.2696.3.2.1.9.21.1.1.10 |
sepSetiTableMeasurement of Severly Errored Second Ratio (SESR) or Severely Errored Time Interval Ratio (SETIR). SEQUENCE OF SepSetiEntry .1.3.6.1.4.1.2696.3.2.1.9.21.2 |
sepSetiEntryRow specification SepSetiEntry .1.3.6.1.4.1.2696.3.2.1.9.21.2.1 |
sepSetiInputNumberTransport Stream on which the measurement is made InputNumber .1.3.6.1.4.1.2696.3.2.1.9.21.2.1.1 |
sepSetiTestStateA 'fail' indicaties that the most recently completed time interval TI was a Severely Errored Time Interval (SETI). A 'pass' indicates that the most recent TI was not severely errored.ro TestState .1.3.6.1.4.1.2696.3.2.1.9.21.2.1.2 |
sepSetiEnableDetermines whether the threshold test and associated traps for this measurement are enabled.rw Enable .1.3.6.1.4.1.2696.3.2.1.9.21.2.1.3 |
sepSetiCounterCount of the number of times an SETI has occurred.ro Counter32 .1.3.6.1.4.1.2696.3.2.1.9.21.2.1.4 |
sepSetiCounterDiscontinuityProvides the last time at which there was a discontinuity in the counter object.ro DateAndTime (SNMPv2-TC) .1.3.6.1.4.1.2696.3.2.1.9.21.2.1.5 |
sepSetiCounterResetThe counter object is reset to zero and the counter discontinuity object is set to the current time if 'true' is written to this object. When read, the value of this object is always 'false'.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.2696.3.2.1.9.21.2.1.6 |
sepSetiLatestErrorThe timestamp at the most recent occurrence of a SETI.ro DateAndTime (SNMPv2-TC) .1.3.6.1.4.1.2696.3.2.1.9.21.2.1.7 |
sepSetiActiveTimeThe total time when it has been possible to perform this measurementro ActiveTime UNITS "second" .1.3.6.1.4.1.2696.3.2.1.9.21.2.1.8 |
sepSetiMeasurementStateSpecifies the validity of the measurement valuero MeasurementState .1.3.6.1.4.1.2696.3.2.1.9.21.2.1.9 |
sepSetiValueThis is the Severely Errored Time Interval Ratio (SETIR) for the most recently completed Measurement Interval (MI). It is expressed as a numeric value.ro FloatingPoint .1.3.6.1.4.1.2696.3.2.1.9.21.2.1.10 |
terrestrialPreferencesTableTable of terrestrial specific measurement preferences. SEQUENCE OF TerrestrialPreferencesEntry .1.3.6.1.4.1.2696.3.2.1.9.100 |
terrestrialPreferencesEntryRow specification TerrestrialPreferencesEntry .1.3.6.1.4.1.2696.3.2.1.9.100.1 |
terrestrialPrefInputNumberTransport Stream input to which the preferences apply InputNumber .1.3.6.1.4.1.2696.3.2.1.9.100.1.1 |
terrestrialPrefCentreFrequencyThis is the centre frequency to which the measuring equipment is tuned for making terrestrial measurements. This frequency is the actual input frequency to the measuring equipment, which may be at an intermediate frequency (IF) rather than the final RF.rw FloatingPoint UNITS "MHz" .1.3.6.1.4.1.2696.3.2.1.9.100.1.2 |
terrestrialPrefBandwidthThe instrument is set to expect a DVB-T transmission adapted for this bandwidth. Normal values will be 6.0MHz, 7.0MHz or 8.0MHz.rw FloatingPoint UNITS "MHz" .1.3.6.1.4.1.2696.3.2.1.9.100.1.3 |
terrestrialPrefModulationThis is the modulation which the measuring equipment expects to see and against which it makes modulation measurements. This applies to terrestrial measurements.rw Modulation .1.3.6.1.4.1.2696.3.2.1.9.100.1.4 |
terrestrialPrefTransmissionModeThe instrument is set to expect a transmission in either 2k mode or 8k mode as set by this object.rw TerrestrialTransmissionMode .1.3.6.1.4.1.2696.3.2.1.9.100.1.5 |
terrestrialPrefGuardIntervalThe instrument is set to expect a transmission using the guard interval specified by this object.rw GuardInterval .1.3.6.1.4.1.2696.3.2.1.9.100.1.6 |
terrestrialPrefHierarchicalThe instrument is set according to the value of this object to expect a transmission which is either non-hierachical or hierarchical using the specified alpha value.rw Hierarchy .1.3.6.1.4.1.2696.3.2.1.9.100.1.7 |
terrestrialPrefCentreFreqExpectedThis is the expected value for the centre frequency as measured by rfAccuracyValue.rw FloatingPoint UNITS "Hz" .1.3.6.1.4.1.2696.3.2.1.9.100.1.8 |
terrestrialPrefCentreFreqLimitThis is the permitted deviation for the centre frequency as measured by rfAccuracyValue. If rfAccuracyValue is outside the range: [terrestrialPrefCentreFreqExpected - terrestrialPrefCentreFreqLimit .. terrestrialPrefCentreFreqExpected + terrestrialPrefCentreFreqLimit] an error will be indicated.rw FloatingPoint UNITS "Hz" .1.3.6.1.4.1.2696.3.2.1.9.100.1.9 |
terrestrialPrefChannelWidthLimitThis is the permitted deviation for the channel width as measured by rfChannelWidthValue. The nominal value of the channel width has a fixed value which depends on the bandwidth (as set by terrestrialPrefBandwidth). If rfChannelWidthValue is outside the range [nominalWidth - terrestrialPrefChannelWidthLimit .. nominalWidth + terrestrialPrefChannelWidthLimit] an error will be indicated.rw FloatingPoint UNITS "Hz" .1.3.6.1.4.1.2696.3.2.1.9.100.1.10 |
terrestrialPrefSymbolLengthLimitThis is the permitted deviation for the symbol length as measured by symbolLengthValue. The nominal value of the symbol length has a fixed value which depends on the bandwidth, the mode and the guard interval (as set by terrestrialPrefBandwidth, terrestrialPrefTransmissionMode and terrestrialPrefGuardInterval respectively). If symbolLengthValue is outside the range [nominalLength - terrestrialPrefSymbolLengthLimit .. nominalLength + terrestrialPrefSymbolLengthLimit] an error will be indicated.rw FloatingPoint UNITS "s" .1.3.6.1.4.1.2696.3.2.1.9.100.1.11 |
terrestrialPrefPowerMinIf the power measured by rfIfPowerValue is less than this value, the associated test fails.rw FloatingPoint UNITS "dBm" .1.3.6.1.4.1.2696.3.2.1.9.100.1.12 |
terrestrialPrefPowerMaxIf the power measured by rfIfPowerValue is greater than this value, the associated test fails.rw FloatingPoint UNITS "dBm" .1.3.6.1.4.1.2696.3.2.1.9.100.1.13 |
terrestrialPrefENDBERBER value which is to be used for the END and ENF measurements.rw FloatingPoint .1.3.6.1.4.1.2696.3.2.1.9.100.1.14 |
terrestrialPrefENDIdealThis is the 'ideal' value of C/N for measurement of END on the whole or high priority stream. It is used in the measurement of eNDTValue.rw FloatingPoint UNITS "dB" .1.3.6.1.4.1.2696.3.2.1.9.100.1.15 |
terrestrialPrefENDMaxIf the measured value of eNDTValue exceeds this, the associated test fails.rw FloatingPoint UNITS "dB" .1.3.6.1.4.1.2696.3.2.1.9.100.1.16 |
terrestrialPrefENFIdealThis is the 'ideal' value of C/N for measurement of ENF on the whole or high priority stream. It is used in the measurement of eNFTValue.rw FloatingPoint UNITS "dB" .1.3.6.1.4.1.2696.3.2.1.9.100.1.17 |
terrestrialPrefENFMaxIf the measured value of eNFTValue is exceeds this value, the associated test fails.rw FloatingPoint .1.3.6.1.4.1.2696.3.2.1.9.100.1.18 |
terrestrialPrefENDLPIdealThis is the 'ideal' value of C/N for measurement of END on the low priority stream. It is used in the measurement of eNDTLPValue.rw FloatingPoint UNITS "dB" .1.3.6.1.4.1.2696.3.2.1.9.100.1.19 |
terrestrialPrefENDLPMaxIf the measured value of eNDTLPValue exceeds this, the associated test fails.rw FloatingPoint UNITS "dB" .1.3.6.1.4.1.2696.3.2.1.9.100.1.20 |
terrestrialPrefENFLPIdealThis is the 'ideal' value of C/N for measurement of ENF on the low priority stream. It is used in the measurement of eNFTLPValue.rw FloatingPoint UNITS "dB" .1.3.6.1.4.1.2696.3.2.1.9.100.1.21 |
terrestrialPrefENFLPMaxIf the measured value of eNFTLPValue exeeds this value, the associated test fails.rw FloatingPoint UNITS "dB" .1.3.6.1.4.1.2696.3.2.1.9.100.1.22 |
terrestrialPrefLinearityMinIf the shoulder attenuation as measured by linearityValue is less than this value, an error is indicated.rw FloatingPoint UNITS "dB" .1.3.6.1.4.1.2696.3.2.1.9.100.1.23 |
terrestrialPrefBERViterbiMaxIf the BER measured by berViterbiTValue exceeds this value, an error is indicated.rw FloatingPoint .1.3.6.1.4.1.2696.3.2.1.9.100.1.24 |
terrestrialPrefBERViterbiLPMaxIf the BER measured by berViterbiTLPValue exceeds this value, an error is indicated.rw FloatingPoint .1.3.6.1.4.1.2696.3.2.1.9.100.1.25 |
terrestrialPrefBERRSMaxIf the BER measured by berRSValue exceeds this value, an error is indicated.rw FloatingPoint .1.3.6.1.4.1.2696.3.2.1.9.100.1.26 |
terrestrialPrefBERRSLPMaxIf the BER measured by berRSLPValue exceeds this value, an error is indicated.rw FloatingPoint .1.3.6.1.4.1.2696.3.2.1.9.100.1.27 |
terrestrialPrefMerTMinIf merTValue is less than this value, the associated test fails.rw FloatingPoint .1.3.6.1.4.1.2696.3.2.1.9.100.1.28 |
terrestrialPrefSteMeanMaxIf steMeanTValue exceeds this value, the associated test fails.rw FloatingPoint UNITS "dB" .1.3.6.1.4.1.2696.3.2.1.9.100.1.29 |
terrestrialPrefSteDeviationMaxIf steDeviationTValue exceeds this value, the associated test fails.rw FloatingPoint UNITS "dB" .1.3.6.1.4.1.2696.3.2.1.9.100.1.30 |
terrestrialPrefCsMinIf csTValue is less than this value, the associated test failsrw FloatingPoint UNITS "dB" .1.3.6.1.4.1.2696.3.2.1.9.100.1.31 |
terrestrialPrefAiMaxIf aiTValue exceeds this value, the associated test fails.rw FloatingPoint UNITS "dB" .1.3.6.1.4.1.2696.3.2.1.9.100.1.32 |
terrestrialPrefQeMaxIf qeTValue exceeds this value, the associated test fails.rw FloatingPoint UNITS "dB" .1.3.6.1.4.1.2696.3.2.1.9.100.1.33 |
terrestrialPrefPjMaxIf pjTValue exceeds this value, the associated test fails.rw FloatingPoint UNITS "dB" .1.3.6.1.4.1.2696.3.2.1.9.100.1.34 |
terrestrialPrefMIPTimingLimitThis preference affects the MIP_timing_error test. If the calculated value of nT differs from an integral number of seconds by more than terrestrialPrefMIPTimingLimit then an error is indicated.rw FloatingPoint UNITS "second" .1.3.6.1.4.1.2696.3.2.1.9.100.1.35 |
terrestrialPrefMIPDeviationMaxThis preference affects the MIP_ts_rate_error test. It is the value of Max_deviation in the inequality given in TR 101 290 as the condition for an error indication.rw FloatingPoint UNITS "bit/s" .1.3.6.1.4.1.2696.3.2.1.9.100.1.36 |
terrestrialPrefSEPUATModeDetermines whether the 'N consecutive' or 'rolling window' mode of determining the start of a period of Unavailable Time (UAT) is used. If the 'N consecutive' mode is selected, the 'M' and 'T' preference parameters are ignored. Likewise, if the 'rolling window' mode is selected, the 'N' preference parameter is ignored.rw UATMode .1.3.6.1.4.1.2696.3.2.1.9.100.1.37 |
terrestrialPrefSEPNThe N value used to identify the start and end of a period of unavailable time (UAT).rw Unsigned32 .1.3.6.1.4.1.2696.3.2.1.9.100.1.38 |
terrestrialPrefSEPTThe T value used to identify the start and end of a period of unavailable time (UAT).rw FloatingPoint UNITS "second" .1.3.6.1.4.1.2696.3.2.1.9.100.1.39 |
terrestrialPrefSEPMThe M value used to identify the start and end of a period of unavailable time (UAT).rw Unsigned32 .1.3.6.1.4.1.2696.3.2.1.9.100.1.40 |
terrestrialPrefSEPTIEach Time Interval of this length is assessed as to whether it is an Errored Time Interval or a Severely Errored Time Interval.rw FloatingPoint UNITS "second" .1.3.6.1.4.1.2696.3.2.1.9.100.1.41 |
terrestrialPrefSEPEBPerCentIf more than this percentage of blocks within a Time Interval is an Errored Block, the Time Interval is a Severely Errored Time Interval (SETI). Example values are: '1.53', '10', '0.33'.rw FloatingPoint .1.3.6.1.4.1.2696.3.2.1.9.100.1.42 |
terrestrialPrefSEPMeasurementIntervalThe Measurement Interval (MI) over which the ESR/ETIR and SESR/SETIR are calculated.rw FloatingPoint UNITS "second" .1.3.6.1.4.1.2696.3.2.1.9.100.1.43 |
tr101290Conformance OBJECT IDENTIFIER .1.3.6.1.4.1.2696.3.2.3 |
tr101290Compliances OBJECT IDENTIFIER .1.3.6.1.4.1.2696.3.2.3.1 |
complianceTransportStreamCompliance for Transport Stream monitor devices Unknown .1.3.6.1.4.1.2696.3.2.3.1.1 |
complianceCableCompliance for Cable RF measurement devices Unknown .1.3.6.1.4.1.2696.3.2.3.1.2 |
complianceSatelliteCompliance for Satellite RF measurement devices Unknown .1.3.6.1.4.1.2696.3.2.3.1.3 |
complianceTerrestrialCompliance for Terrestrial RF measurement devices Unknown .1.3.6.1.4.1.2696.3.2.3.1.4 |
tr101290ObjectGroups OBJECT IDENTIFIER .1.3.6.1.4.1.2696.3.2.3.2 |
groupControlContains all the objects from the tr101290Control branch of the MIB Unknown .1.3.6.1.4.1.2696.3.2.3.2.1 |
groupTrapControlContains all the normal objects from the tr101290Trap branch of the MIB Unknown .1.3.6.1.4.1.2696.3.2.3.2.2 |
groupTrapsContains all the traps/notifications from the MIB. Unknown .1.3.6.1.4.1.2696.3.2.3.2.3 |
groupCapabilityContains all objects from the tr101290Capability branch of the MIB Unknown .1.3.6.1.4.1.2696.3.2.3.2.4 |
groupTransportStreamContains all objects relevant to Transport Stream measurement Unknown .1.3.6.1.4.1.2696.3.2.3.2.5 |
groupCableContains all objects relevant to cable RF measurement Unknown .1.3.6.1.4.1.2696.3.2.3.2.6 |
groupSatelliteContains all objects relevent to satellite RF measurements Unknown .1.3.6.1.4.1.2696.3.2.3.2.7 |
groupTerrestrialContains all objects relevant to terrestrial RF measurements Unknown .1.3.6.1.4.1.2696.3.2.3.2.8 |