DVB-CABLE-INA-IF-MIB
AI MIB Summary
The DVB-CABLE-INA-IF-MIB provides SNMP management interfaces for EuroModem-compliant Interface Network Adapters (INAs) within DVB-Cable networks, extending MIB-II RFC 1213 to monitor physical and data link layer parameters such as interface status, error counters, and signal quality metrics specific to cable modem operations.
The MIB modules for INAs that conform to the EuroModem specification. This MIB assumes the INA implements MIB-II RFC 1213 The original MIB definition work was carried out for the DVB-RC group by Bert Van Willigen Philips Research Laboratory Eindhoven, The Netherlands.
Main OID:
dvbInaIf.1.3.6.1.2.1.10.146
301
Objects
Active
Status
5
Dependencies
Imported Objects
Objects
301 total| Object Name |
|---|
dvbInaIfThe MIB modules for INAs that conform to the EuroModem specification. This MIB assumes the INA implements MIB-II RFC 1213 The original MIB definition work was carried out for the DVB-RC group by Bert Van Willigen Philips Research Laboratory Eindhoven, The Netherlands. MODULE-IDENTITY .1.3.6.1.2.1.10.146 |
dvbInaIfMIBObjects OBJECT IDENTIFIER .1.3.6.1.2.1.10.146.1 |
dvbInaIfMac OBJECT IDENTIFIER .1.3.6.1.2.1.10.146.1.1 |
dvbInaIfMacTableDescribes the attributes of each MAC interface, extending the information available from ifEntry. SEQUENCE OF DvbInaIfMacEntry .1.3.6.1.2.1.10.146.1.1.1 |
dvbInaIfMacEntryAn entry containing objects describing attributes of each MAC entry, extending the information in ifEntry. An entry in this table exists for each ifEntry with an ifType of dvbRecMacLayer(146). The state of the MAC depends on the state of the INA. If the INA is not operational also the MAC is not operational. DvbInaIfMacEntry .1.3.6.1.2.1.10.146.1.1.1.1 |
dvbInaIfMacDeviceCapabilitiesThis 32-bit object specifies the maximum capabilities of this MAC entity. This is the possible set of capability for this INA.ro OCTET STRING ( SIZE (4)) .1.3.6.1.2.1.10.146.1.1.1.1.1 |
dvbInaIfMacDeviceExtendedCapabilitiesThis 32-bit object specifies the maximum extended capabilities of this MAC entity. This is the possible set of capability for this INA.ro OCTET STRING ( SIZE (4)) .1.3.6.1.2.1.10.146.1.1.1.1.2 |
dvbInaIfMacCapabilitiesThis 32-bit object specifies the capabilities of this MAC entity. It is equal to or a subset of dvbInaIfMacDeviceCapabilities. Default this parameter is equal to dvbInaIfMacDeviceCapabilities. The object can be used to restrict the capabilities for this MAC entity.rw OCTET STRING ( SIZE (4)) .1.3.6.1.2.1.10.146.1.1.1.1.3 |
dvbInaIfMacExtendedCapabilitiesThis 32-bit object specifies the extended capabilities of this MAC entity. It is equal to or a subset of dvbInaIfMacDeviceExtendedCapabilities. Default this parameter is equal to dvbInaIfMacDeviceExtendedCapabilities. The object can be used to restrict the extended capabilities for this MAC entity.rw OCTET STRING ( SIZE (4)) .1.3.6.1.2.1.10.146.1.1.1.1.4 |
dvbInaIfMacProtocolSupportSpecifies the MAC standard version supported by this MAC entity. Optional, this parameter can be written to force a particular MAC version to be executed by the INA.rw Enumeration .1.3.6.1.2.1.10.146.1.1.1.1.5 |
dvbInaIfMacTimeout0Time-out value 0x0.rw EtsTimeOut .1.3.6.1.2.1.10.146.1.1.1.1.6 |
dvbInaIfMacTimeout1Time-out value 0x1.rw EtsTimeOut .1.3.6.1.2.1.10.146.1.1.1.1.7 |
dvbInaIfMacTimeout2Time-out value 0x2.rw EtsTimeOut .1.3.6.1.2.1.10.146.1.1.1.1.8 |
dvbInaIfMacTimeout3Time-out value 0x3.rw EtsTimeOut .1.3.6.1.2.1.10.146.1.1.1.1.9 |
dvbInaIfMacTimeout4Time-out value 0x4.rw EtsTimeOut .1.3.6.1.2.1.10.146.1.1.1.1.10 |
dvbInaIfMacTimeoutDTime-out value 0xD. Terminal Time-Out, Security Sign-On.rw EtsTimeOut .1.3.6.1.2.1.10.146.1.1.1.1.11 |
dvbInaIfMacTimeoutETime-out value 0xE. Terminal Time-Out, Main Key Exchange.rw EtsTimeOut .1.3.6.1.2.1.10.146.1.1.1.1.12 |
dvbInaIfMacTimeoutFTime-out value 0xF. Terminal Time-Out, Quick/Explicit Key exchange.rw EtsTimeOut .1.3.6.1.2.1.10.146.1.1.1.1.13 |
dvbInaIfMacRapidSignOnEnableThis Boolean parameter specifies whether the NIU's are allowed to do a rapid sign-on when they enter the sign-on process. (See the Need_Calibration bit in the <MAC> Sign-On_Request_Message.). By default this object is False.rw TruthValue (SNMPv2-TC) .1.3.6.1.2.1.10.146.1.1.1.1.14 |
dvbInaIfMacRespCollTimeWindowSpecifies the maximum time for the sign-on response message transmission randomisation.rw Unsigned32 ( 0..65535 ) UNITS "ms" .1.3.6.1.2.1.10.146.1.1.1.1.15 |
dvbInaIfMacAddressFilterUseThis setting controls the use of the of the Address filter in the Sign-On Request Message. Disabled : The address filter is not used. Managed : The manager can control the use of the address filter with dvbInaIfMacAddressPositionMask and dvbInaIfMacAddressComparisonValue Automatic : The INA controls use of the address filter itself. The readback values of dvbInaIfMacAddressPositionMask and dvbInaIfMacAddressComparisonValue will not necessary reflect the values used by the INA.rw Enumeration .1.3.6.1.2.1.10.146.1.1.1.1.16 |
dvbInaIfMacAddressPositionMaskIndicates the bit positions in the NIU MAC address that are used for address filtering comparison.rw INTEGER ( 0..255 ) .1.3.6.1.2.1.10.146.1.1.1.1.17 |
dvbInaIfMacAddressComparisonValueSpecifies the value that the NIU should use for MAC address comparison.rw INTEGER ( 0..255 ) .1.3.6.1.2.1.10.146.1.1.1.1.18 |
dvbInaIfMacGrantProtocolTimeOutDefault value for the time that the NIU should wait before verifying the status of pending grants. See also dvbInaIfNiuGrantProtocolTimeOut.rw Unsigned32 ( 0..65535 ) UNITS "ms" .1.3.6.1.2.1.10.146.1.1.1.1.19 |
dvbInaIfMacIdleIntervalSpecifies the transmission interval in seconds to be used for the MAC Idle message. When this value is zero, no idle messages shall be sent.rw Unsigned32 ( 0 | 60..600 ) UNITS "s" .1.3.6.1.2.1.10.146.1.1.1.1.20 |
dvbInaIfMacIdleInvalidCountSpecifies a MAC Idle message invalid period in number of dvbInaIfMacIdleInterval, after which the NIU is declared to be signed-off. For example, if dvbInaIfMacIdleInterval is 5 seconds and this parameter is 3, then if in 15 seconds no data and/or MAC Idle messages are received, the INA will assume that the NIU in question has signed-off. This object is only valid when dvbInaIfMacIdleInterval is non-zero.rw INTEGER ( 0..255 ) UNITS "Number of dvbInaIfMacIdleIntervals" .1.3.6.1.2.1.10.146.1.1.1.1.21 |
dvbInaIfMacNMaximum value of the upstream slot position register.rw INTEGER ( 0..1023 ) .1.3.6.1.2.1.10.146.1.1.1.1.22 |
dvbInaIfMacMaxContentionMsgLenThe default value for the Maximum_Contention_Access_Message_Length in the Connect Message. This is the maximum length of a message that may be transmitted using contention access. Any message greater than this should use reservation access. See also dvbInaIfConMaxContentionMsgLen.rw INTEGER ( 1..255 ) UNITS "ATM cells" .1.3.6.1.2.1.10.146.1.1.1.1.23 |
dvbInaIfMacMaxReservationMsgLenThe default value for the Maximum_Reservation_Access_Message_Length in the Connect Message. This is the maximum length of a message that may be transmitted using a single reservation access. Any message greater than this should be transmitted by making multiple reservation requests. See also dvbInaIfConMaxReservationMsgLen.rw INTEGER ( 1..255 ) UNITS "ATM cells" .1.3.6.1.2.1.10.146.1.1.1.1.24 |
dvbInaIfMacNiuCountNumber of connected NIUs.ro Gauge32 .1.3.6.1.2.1.10.146.1.1.1.1.25 |
dvbInaIfMacConnectionsThe number of connections currently active for this MAC entity.ro Gauge32 .1.3.6.1.2.1.10.146.1.1.1.1.26 |
dvbInaIfMacUnknownNiuErrorThis value is incremented if a message is received from a unknown NIU, except if it is a SignOn_Response Message.ro Counter32 .1.3.6.1.2.1.10.146.1.1.1.1.27 |
dvbInaIfMacMsgDataErrorThis value is incremented if a MAC message is received with a data error, i.e. 1) is too short, 2) has an illegal Connection ID or Reservation ID, 3) is a reservation message from a NIU not reservation capable, 4) is a security message from a NIU not security capable 5) is an illegal MAC message.ro Counter32 .1.3.6.1.2.1.10.146.1.1.1.1.28 |
dvbInaIfMacMsgHdrErrorThis value is incremented if a MAC message is received with a header error, i.e. 1) is too short, 2) does not contain a MAC address.ro Counter32 .1.3.6.1.2.1.10.146.1.1.1.1.29 |
dvbInaIfMacInvalidNiuThis value is incremented if a MAC Initialisation Complete Message is transmitted with the Invalid_STB/NIU bit set.ro Counter32 .1.3.6.1.2.1.10.146.1.1.1.1.30 |
dvbInaIfMacTimingRangingErrorThis value is incremented if a MAC Initialisation Complete Message is transmitted with the Timing_Ranging_Error bit set.ro Counter32 .1.3.6.1.2.1.10.146.1.1.1.1.31 |
dvbInaIfMacPowerRangingErrorThis value is incremented if a MAC Initialisation Complete Message is transmitted with the Power_Ranging_Error bit set.ro Counter32 .1.3.6.1.2.1.10.146.1.1.1.1.32 |
dvbInaIfMacOtherSignOnErrorThis value is incremented if a MAC Initialisation Complete Message is transmitted with the Other_Error bit set.ro Counter32 .1.3.6.1.2.1.10.146.1.1.1.1.33 |
dvbInaIfProvision OBJECT IDENTIFIER .1.3.6.1.2.1.10.146.1.2 |
dvbInaIfProvChTableThis table specifies the information for the Default Configuration Message transmitted on the Provisioning channel. SEQUENCE OF DvbInaIfProvChEntry .1.3.6.1.2.1.10.146.1.2.1 |
dvbInaIfProvChEntryAn entry containing objects describing information for the Default Configuration Message transmitted on the Provisioning channel. More than one downstream can use than same entry or different entries can be made for different downstreams. If provisioning is done on an other INA, this table will be empty. DvbInaIfProvChEntry .1.3.6.1.2.1.10.146.1.2.1.1 |
dvbInaIfProvChIndexIndex of this table entry. INTEGER ( 0..255 ) .1.3.6.1.2.1.10.146.1.2.1.1.1 |
dvbInaIfProvChRowAccessStatusControls and reflects the status of this row in this table.rw RowStatus (SNMPv2-TC) .1.3.6.1.2.1.10.146.1.2.1.1.2 |
dvbInaIfProvChServiceChIfIndexThe ifIndex of the upstream channel used as Service Channel for the provisioning.rw InterfaceIndex (IF-MIB) .1.3.6.1.2.1.10.146.1.2.1.1.3 |
dvbInaIfProvChBackupServiceChIfIndexThe ifIndex of the upstream channel used as Backup Service Channel for the provisioning.rw InterfaceIndex (IF-MIB) .1.3.6.1.2.1.10.146.1.2.1.1.4 |
dvbInaIfProvChIncrPowerRetryCountSpecifies the number of attempts the NIU should do to enter the system at the same power level before incrementing its upstream transmit power for this MAC entity.rw INTEGER ( 0..255 ) .1.3.6.1.2.1.10.146.1.2.1.1.5 |
dvbInaIfProvChMaxPowerLevelSpecifies the maximum power in dBuV the NIU is allowed to transmit upstream for this MAC entity.rw INTEGER ( 0..255 ) UNITS "dBuV" .1.3.6.1.2.1.10.146.1.2.1.1.6 |
dvbInaIfProvChMinPowerLevelSpecifies the minimum power in dBuV the NIU has to transmit upstream for this MAC entity.rw INTEGER ( 0..255 ) UNITS "dBuV" .1.3.6.1.2.1.10.146.1.2.1.1.7 |
dvbInaIfProvChMaxBackOffExponentSpecifies the maximum back off exponent counter for this MAC entity.rw INTEGER ( 0..255 ) .1.3.6.1.2.1.10.146.1.2.1.1.8 |
dvbInaIfProvChMinBackOffExponentSpecifies the minimum back off exponent counter for this MAC entity.rw INTEGER ( 0..255 ) .1.3.6.1.2.1.10.146.1.2.1.1.9 |
dvbInaIfProvChAbsoluteTimeOffsetSpecifies the default absolute time offset in 100 ns units to be used for first sign-on of a NIU for this MAC entity.rw INTEGER ( -32768..32767 ) UNITS "100ns" .1.3.6.1.2.1.10.146.1.2.1.1.10 |
dvbInaIfDsCh OBJECT IDENTIFIER .1.3.6.1.2.1.10.146.1.3 |
dvbInaIfDsChTableThis table describes the attributes of downstream channels (frequency bands). SEQUENCE OF DvbInaIfDsChEntry .1.3.6.1.2.1.10.146.1.3.1 |
dvbInaIfDsChEntryList of attributes for a single Downstream channel. An entry in this table exists for each downstream ifEntry. DvbInaIfDsChEntry .1.3.6.1.2.1.10.146.1.3.1.1 |
dvbInaIfDsChFrequencyThe centre of the downstream frequency associated with this channel.rw DownFrequency UNITS "hertz" .1.3.6.1.2.1.10.146.1.3.1.1.1 |
dvbInaIfDsChConnectionsSpecifies the number of connections currently active for this down stream channel.ro Gauge32 .1.3.6.1.2.1.10.146.1.3.1.1.2 |
dvbInaIfDsChTxPowerSpecifies the down stream transmission power in dBuV of this interface.rw INTEGER ( 0..255 ) UNITS "dBuV" .1.3.6.1.2.1.10.146.1.3.1.1.3 |
dvbInaIfDsChDownCoaxIdSpecifies the coax ID of the Downstream HFC segment to which the downstream channel is connected. By default this parameter is zero.rw Unsigned32 ( 0..4294967295 ) .1.3.6.1.2.1.10.146.1.3.1.1.4 |
dvbInaIfDsChSymbolRateSpecifies the symbol rate for the Downstream channel.rw DownstreamSymbolrate UNITS "symbol/s" .1.3.6.1.2.1.10.146.1.3.1.1.5 |
dvbInaIfDsChModulationSpecifies the modulation for the Downstream channel.rw Modulation .1.3.6.1.2.1.10.146.1.3.1.1.6 |
dvbInaIfDsChTypeSpecifies if the Downstream channel is inband or out-of-band.rw Enumeration .1.3.6.1.2.1.10.146.1.3.1.1.7 |
dvbInaIfDsChDefaultPIDThe default value of the MPEG PID of the elementary stream that carries the data on this downstream. See also dvbInaIfConPID.rw Unsigned32 ( 0..8191 ) .1.3.6.1.2.1.10.146.1.3.1.1.8 |
dvbInaIfDsChProvFrequencySpecifies the Downstream frequency of the provisioning channel. This setting is always used, no matter the provisioning channel is on this INA or on another. If the provisioning channel is on this INA, the value will be the frequency of one of the downstreams.rw DownFrequency .1.3.6.1.2.1.10.146.1.3.1.1.9 |
dvbInaIfDsChProvDownstreamTypeSpecifies the type of the downstream provisioning channel in the Provisioning Channel Message. 0 = QAM_MPEG, 1 = QPSK_1,544, 2 = QPSK_3,088 3..255 Reserved This setting is always used, no matter the provisioning channel is on this INA or on another. If the provisioning channel is on this INA, the value can be derived from the ib/oob type and modulation.rw INTEGER ( 0..255 ) .1.3.6.1.2.1.10.146.1.3.1.1.10 |
dvbInaIfDsChProvEnableSpecifies if this downstream channel is a Provisioning channel and as such transmits the Default Configuration Message. true = Provisioning channel false = not a Provisioning channel.rw TruthValue (SNMPv2-TC) .1.3.6.1.2.1.10.146.1.3.1.1.11 |
dvbInaIfDsChProvTableIndexIf this downstream channel is a provisioning channel, then an index to the Provisioning tabel must be give here.rw INTEGER ( 0..255 ) .1.3.6.1.2.1.10.146.1.3.1.1.12 |
dvbInaIfUsCh OBJECT IDENTIFIER .1.3.6.1.2.1.10.146.1.4 |
dvbInaIfUsChTableDescribes the attributes of attached upstream channels (frequency bands). SEQUENCE OF DvbInaIfUsChEntry .1.3.6.1.2.1.10.146.1.4.1 |
dvbInaIfUsChEntryList of attributes for a single upstream channel. The state of the upstream channel depends on the state of the MAC and downstream channel. If one of both or both are non-operational also the state upstream channel(s) shall be ready. That in the case of Space division Multiplex SDM each upstream channel has a different non-zero Coax ID. DvbInaIfUsChEntry .1.3.6.1.2.1.10.146.1.4.1.1 |
dvbInaIfUsChFrequencySpecifies the frequency in Hz of the carrier used for this upstream channel.rw UpFrequency UNITS "hertz" .1.3.6.1.2.1.10.146.1.4.1.1.1 |
dvbInaIfUsChSymbolRateSpecifies the symbol rate for this upstream channel.rw UpstreamSymbolrate .1.3.6.1.2.1.10.146.1.4.1.1.2 |
dvbInaIfUsChModulationSpecifies the modulation for this upstream channel.rw Modulation .1.3.6.1.2.1.10.146.1.4.1.1.3 |
dvbInaIfUsChMacFlagSetSpecifies the MAC flag set assigned to this upstream channel.ro MacFlagSet .1.3.6.1.2.1.10.146.1.4.1.1.4 |
dvbInaIfUsChIdSpecifies the logical channel number associated with this upstream channel.ro INTEGER ( 0..255 ) .1.3.6.1.2.1.10.146.1.4.1.1.5 |
dvbInaIfUsChConnectionsSpecifies the number of connections currently active for this upstream channel.ro Gauge32 .1.3.6.1.2.1.10.146.1.4.1.1.6 |
dvbInaIfUsChCalibrationRxPowerSpecifies the target receive signal power in dBuV to which the NIUs on this upstream channel are calibratedrw INTEGER ( 0..255 ) UNITS "dBuV" .1.3.6.1.2.1.10.146.1.4.1.1.9 |
dvbInaIfUsChUpCoaxIdSpecifies the coax ID of the UpStream HFC segment to which the upstream channel is connected. By default this parameter is zero.rw Unsigned32 ( 0..4294967295 ) .1.3.6.1.2.1.10.146.1.4.1.1.10 |
dvbInaIfUsChDownCoaxIdSpecifies the coax ID of the Downstream HFC segment to which the upstream channel is connected. By default this parameter is zero.rw Unsigned32 ( 0..4294967295 ) .1.3.6.1.2.1.10.146.1.4.1.1.11 |
dvbInaIfUsChAtmCellsTotal number of recieved ATM Cells. 0 can indicate the counter is not supported.ro Counter64 .1.3.6.1.2.1.10.146.1.4.1.1.12 |
dvbInaIfUsChAtmTimingErrorsNumber of ATM Cells received with Timing Error. 0 can indicate the counter is not supported.ro Counter64 .1.3.6.1.2.1.10.146.1.4.1.1.13 |
dvbInaIfUsChAtmPowerErrorsNumber of ATM Cells received with Signal Level Error. 0 can indicate the counter is not supported.ro Counter64 .1.3.6.1.2.1.10.146.1.4.1.1.14 |
dvbInaIfUsChAtmRSCorrectableErrorsNumber of ATM Cells received with correctable Reed-Solomon Errors. 0 can indicate the counter is not supported.ro Counter64 .1.3.6.1.2.1.10.146.1.4.1.1.15 |
dvbInaIfUsChAtmRSNonCorrectableErrorsNumber of ATM Cells received with non-correctable Reed-Solomon Errors. 0 can indicate the counter is not supported.ro Counter64 .1.3.6.1.2.1.10.146.1.4.1.1.16 |
dvbInaIfUsChAtmHecErrorsNumber of ATM Cells received with HEC Error. 0 can indicate the counter is not supported.ro Counter64 .1.3.6.1.2.1.10.146.1.4.1.1.17 |
dvbInaIfUsChAal5CrcErrorsNumber AAL5 frames received with CRC error. 0 can indicate the counter is not supported.ro Counter64 .1.3.6.1.2.1.10.146.1.4.1.1.18 |
dvbInaIfUsChAtmCollisionErrorsNumber of ATM Cells received with Collision detected. 0 can indicate the counter is not supported.ro Counter64 .1.3.6.1.2.1.10.146.1.4.1.1.19 |
dvbInaIfNiu OBJECT IDENTIFIER .1.3.6.1.2.1.10.146.1.5 |
dvbInaIfNiuTableDescribes the attributes of Network Interface Units. SEQUENCE OF DvbInaIfNiuEntry .1.3.6.1.2.1.10.146.1.5.1 |
dvbInaIfNiuEntryInitially the table shall be empty. A new entry for a NIU is automatically created when the NIU in question signs on. Furthermore, the manager through the dvbInaIfNiuRowAccessStatus object can create new entries. This can be used in the case of re-provisioning where by the manager first makes an entry and sets all relevant parameters before the NIU is re-provisioned to this INA. When an entry is created for a NIU, also automatically an entry is created in the connection table for the default connection of the NIU in question. When a NIU entry is deleted, also all associated connection entries are deleted. DvbInaIfNiuEntry .1.3.6.1.2.1.10.146.1.5.1.1 |
dvbInaIfNiuMacAddressA 48-bit value representing the unique MAC address of the NIU. MacAddress (SNMPv2-TC) .1.3.6.1.2.1.10.146.1.5.1.1.1 |
dvbInaIfNiuRowAccessStatusControls and reflects the status of this row in this table.rw RowStatus (SNMPv2-TC) .1.3.6.1.2.1.10.146.1.5.1.1.2 |
dvbInaIfNiuStateReturned status information is the NIU status as assumed by the INA. The following states are possible: null(1) Any state other than below. ranging(2): The NIU has responded to a [MAC] Sign-on Request Message but the time ranging and power calibration is not yet complete. rangingAborted(3), The INA has sent a Initalisation Complete Message to the NIU with Completion_Status_Field != 0 rangingComplete(4), The INA has sent a Initalisation Complete Message to the NIU with Completion_Status_Field = 0 connecting(5), The INA has sent a Connect Message for first connection and is waiting for a Connect Response Message from the NIU. connectComplete(6) The INA has sent a Connect Confirm Message for first connection to the NIU. stopped(7) The NUI is in the stopped transmission state after the INA has send a Stop_Upstream_Transmission to the NIU and the NIU has returned a Link Management Response. NOTE: The INA only needs to report states it is able to detect.ro Enumeration .1.3.6.1.2.1.10.146.1.5.1.1.3 |
dvbInaIfNiuDesiredStateSpecifies the desired state of the NIU. This parameter can be set to one of the following values: down : Initial state. Disable NIU operation. start : Enable NIU operation. stop : Stop upstream transmission from the NIU.rw Enumeration .1.3.6.1.2.1.10.146.1.5.1.1.4 |
dvbInaIfNiuDownIfIndexSpecifies the IfIndex of the downstream channel on which the NIU is tuned.ro InterfaceIndexOrZero (IF-MIB) .1.3.6.1.2.1.10.146.1.5.1.1.5 |
dvbInaIfNiuUpIfIndexSpecifies the IfIndex of the upstream channel that is used by the NIU.ro InterfaceIndexOrZero (IF-MIB) .1.3.6.1.2.1.10.146.1.5.1.1.6 |
dvbInaIfNiuUpTxLevelSpecifies the upstream transmit level. This is the INA notion of NIU transmit level. (See also 'dvbInaIfNiuRespTxLevel'.)ro INTEGER ( 0..255 ) UNITS "dBuV" .1.3.6.1.2.1.10.146.1.5.1.1.7 |
dvbInaIfNiuTimeOffsetSpecifies the time offset. This is the INA notion of NIU time offset. (See also 'dvbInaIfNiuRespTimeOffset'.)ro Integer32 ( -32768..32767 ) UNITS "100ns" .1.3.6.1.2.1.10.146.1.5.1.1.8 |
dvbInaIfNiuStatusThis 32-bit object specifies the status of this NIU. See <MAC> Sign-On Response Message and <MAC> Status Response Message [1] for the exact bit assignment. This object is updated after the reception of a <MAC> Status Response Message [1].ro Unsigned32 ( 0..4294967295 ) .1.3.6.1.2.1.10.146.1.5.1.1.9 |
dvbInaIfNiuErrorCodeThis 16-bit object specifies the error code in the <MAC> Sign-On Response Message. See ES 200 800 for the exact bit assignment.ro Unsigned32 ( 0..65535 ) .1.3.6.1.2.1.10.146.1.5.1.1.10 |
dvbInaIfNiuRetryCountThis 8-bit object specifies the number of transmissions of the <MAC> Sign-On Response Message. (See [1]).ro INTEGER ( 0..255 ) .1.3.6.1.2.1.10.146.1.5.1.1.11 |
dvbInaIfNiuCapabilitiesThis 32-bit object specifies the capabilities of this NIU. See also ES 200 800 for the bit assignment.ro OCTET STRING ( SIZE (4)) .1.3.6.1.2.1.10.146.1.5.1.1.12 |
dvbInaIfNiuExtendedCapabilitiesThis 32-bit object specifies the extended capabilities of this NIU. See also ES 200 800 and ECR 5 for the bit assignment.ro OCTET STRING ( SIZE (4)) .1.3.6.1.2.1.10.146.1.5.1.1.13 |
dvbInaIfNiuInitCompletionStatusThis 8-bit object indicates the errors in the initialisation phase of this NIU. See the <MAC> Initialization Complete Message ES 200 800 for the exact bit assignment.ro INTEGER ( 0..255 ) .1.3.6.1.2.1.10.146.1.5.1.1.14 |
dvbInaIfNiuRequestStatusThis object triggers the transmission of a <MAC> Status Request Message [1]. This parameter can be set to one of the following parameters: 'NiuReqAddressPars(0)': request address parameters, 'NiuReqErrorPars(1)': request error parameters, 'NiuReqConnectionsPars(2)': request connection parameters, and 'NiuReqPhyLayerPars(3)': request physical layer parameters. When read this object returns 'NiuReqAddressPars(0)'.rw Enumeration .1.3.6.1.2.1.10.146.1.5.1.1.15 |
dvbInaIfNiuResponseNumberThis object is incremented when a <MAC> Status Response Message [1] is received. This object can be polled to detect the reception of this message. After reset this object is zero.ro Counter32 .1.3.6.1.2.1.10.146.1.5.1.1.16 |
dvbInaIfNiuRespTxLevelSpecifies the transmit power level of the NIU. This object is updated after the reception of a <MAC> Status Response Message [1] that is a response on the 'NiuReqPhyLayerPars(3)' request.ro INTEGER ( 0..255 ) UNITS ".5 dBuV" .1.3.6.1.2.1.10.146.1.5.1.1.17 |
dvbInaIfNiuRespTimeOffsetSpecifies the time offset of the NIU. This object is updated after the reception of a <MAC> Status Response Message [1] that is a response on the 'NiuReqPhyLayerPars(3)' request.ro Integer32 ( -32768..32767 ) UNITS "100ns" .1.3.6.1.2.1.10.146.1.5.1.1.18 |
dvbInaIfNiuRespOoBDownFrequencySpecifies the OoB downstream frequency of the NIU. This object is updated after the reception of a <MAC> Status Response Message [1] that is a response on the 'NiuReqPhyLayerPars(3)' request.ro DownFrequency .1.3.6.1.2.1.10.146.1.5.1.1.19 |
dvbInaIfNiuRespIBDownFrequencySpecifies the IB downstream frequency of the NIU. This object is updated after the reception of a <MAC> Status Response Message [1] that is a response on the 'NiuReqPhyLayerPars(3)' request.ro DownFrequency .1.3.6.1.2.1.10.146.1.5.1.1.20 |
dvbInaIfNiuRespSNRLevelSpecifies the estimated SNR level at the RF input of the NIU. This object is updated after the reception of a <MAC> Status Response Message [1] that is a response on the 'NiuReqPhyLayerPars(3)' request.ro INTEGER ( 0..255 ) UNITS "dB" .1.3.6.1.2.1.10.146.1.5.1.1.21 |
dvbInaIfNiuRespRxLevelSpecifies the estimated downstream power level of the MAC messages at the RF input of the NIU. This object is updated after the reception of a <MAC> Status Response Message [1] that is a response on the 'NiuReqPhyLayerPars(3)' request.ro INTEGER ( 0..255 ) UNITS "dBuV" .1.3.6.1.2.1.10.146.1.5.1.1.22 |
dvbInaIfNiuDefaultConnectionIdSpecifies the ConnectionId of the default connection that is assigned to this NIU.rw Unsigned32 ( 0..4294967295 ) .1.3.6.1.2.1.10.146.1.5.1.1.23 |
dvbInaIfNiuLifetimeDefines how long after the NIU was signed off, the entry is removed from the table. An infinite(0) value would mean that the values are stored at least until the next reboot of the INA.rw Unsigned32 ( 0..4294967295 ) UNITS "s" .1.3.6.1.2.1.10.146.1.5.1.1.24 |
dvbInaIfNiuGrantProtocolTimeOutThe time that the NIU should wait before verifying the status of pending grants. Default value is dvbInaIfMacGrantProtocolTimeOut.rw Unsigned32 ( 0..65535 ) UNITS "ms" .1.3.6.1.2.1.10.146.1.5.1.1.25 |
dvbInaIfNiuSlotConfigurationErrNIU Error Parameter: Slot_Configuration_CRC_Error_Count, the number of errors in Slot_Configuration_Count R bytes, as found by the CRC decoder.ro Counter32 .1.3.6.1.2.1.10.146.1.5.1.1.26 |
dvbInaIfNiuAtmPacketLossNIU Error Parameter: ATM_Packet_Loss_Count, the number of received ATM cells that were lost, either due to unrecoverable Reed-Solomon errors or because of an erroneous HEC of the ATM cell header.ro Counter32 .1.3.6.1.2.1.10.146.1.5.1.1.27 |
dvbInaIfNiuSlEsCrcErrNiu Error Parameter: SL-ESF_CRC_Error_Count, the number of CRC errors found in consecutive C1-C6.ro Counter32 .1.3.6.1.2.1.10.146.1.5.1.1.28 |
dvbInaIfNiuSlEsFrameCountNIU Error Parameter: SL-ESF_Frame_Count, the number of frames the statistics apply to.ro Counter32 .1.3.6.1.2.1.10.146.1.5.1.1.29 |
dvbInaIfNiuSlotConfigurationCountNIU Error Parameter: Slot_Configuration_Count, the number of R-byte sets (Rxa-Rxc) used to calculate Slot_Configuration_CRC_Error_Count.ro Counter32 .1.3.6.1.2.1.10.146.1.5.1.1.30 |
dvbInaIfNiuRSErrCorrectableNIU Error Parameter: Reed_Solomon_Errors_Correctable, MPEG frames received with correctable Reed-Solomon Errors (IB only).ro Counter32 .1.3.6.1.2.1.10.146.1.5.1.1.31 |
dvbInaIfNiuRSErrNonCorrectableNIU Error Parameter: Reed_Solomon_Errors_Non_Correctable, MPEG frames received with non-correctable Reed-Solomon Errors (IB only).ro Counter32 .1.3.6.1.2.1.10.146.1.5.1.1.32 |
dvbInaIfNiuSignOnTimeThe value of sysUpTime at the time this NIU was signed on. If the time is unknown, this value shall be zero.ro TimeTicks (SNMPv2-SMI) .1.3.6.1.2.1.10.146.1.5.1.1.33 |
dvbInaIfNiuDsChBytesNumber of bytes sent in direction INA to NIU.ro Counter64 .1.3.6.1.2.1.10.146.1.5.1.1.34 |
dvbInaIfNiuUsChBytesNumber of bytes sent in direction NIU to INA. Includes backbone, NIU-to-NIU and broadcast/multicast traffic.ro Counter64 .1.3.6.1.2.1.10.146.1.5.1.1.35 |
dvbInaIfNiuTimeRangingNumber of times the NIU has been time ranged.ro Counter32 .1.3.6.1.2.1.10.146.1.5.1.1.36 |
dvbInaIfNiuPowerRangingNumber of times the NIU has been power ranged.ro Counter32 .1.3.6.1.2.1.10.146.1.5.1.1.37 |
dvbInaIfConnection OBJECT IDENTIFIER .1.3.6.1.2.1.10.146.1.6 |
dvbInaIfConTableContains information about DVB-RC MAC connections. SEQUENCE OF DvbInaIfConEntry .1.3.6.1.2.1.10.146.1.6.1 |
dvbInaIfConEntryInitially the table shall be empty. A new entry for a connection is automatically generated when a <MAC> Resource Request Message is received from the NIU in question requesting a new connection. Also during reprovisioning new entries are created. Furthermore, the manager through the dvbInaIfConAccessStatus object can create new entries. Connection table entries shall be deleted, when the associated NIU entry is deleted. Furthermore, the manager can delete unused connection entries. The following parameters can only be set when the connection is in state down(1) dvbInaIfConAccessStatus, dvbInaIfConEncapsulation, dvbInaIfConFilterMACAddress, dvbInaIfConPID. DvbInaIfConEntry .1.3.6.1.2.1.10.146.1.6.1.1 |
dvbInaIfConNiuMacAddressMAC address of the NIU that is associated with the connection. MacAddress (SNMPv2-TC) .1.3.6.1.2.1.10.146.1.6.1.1.1 |
dvbInaIfConConnectionIdSpecifies the connection identifier to be used for this connection. Unsigned32 ( 0..4294967295 ) .1.3.6.1.2.1.10.146.1.6.1.1.2 |
dvbInaIfConCurrentStateCurrent state of the connection. The following states are possible: down(1) In this state an entry is made in the connection table for the connection in question. However, there is not (yet) any connection on MAC layer between the INA and NIU. settingUp(2) Either the NIU in question has requested a connection via a [MAC] Resource Request message, or the manager has initiated a (new) connection by setting dvbInaConDesiredState to the state Up. up(3) In this state the connection in question is up and running. breakingDown(4) Either the NIU in question has requested to release the connection via a [MAC] Resource Request message, or the manager has initiated the release of the connection by setting dvbInaConDesiredState to the state: Down. downAlloc(5) In this state an entry is made in the connection table for the connection in question. Furthermore, the bandwidth for the fixed rate connection is allocated. However, the connection doesn't (yet) exist on MAC layer between the INA and NIU. alarm(6) The connection in question is in the alarm state. his means that either the parameter setting is not valid, or the scheduler of the MAC has not the resources to allocate the requested bandwidth for a fixed rate connection, or the NIU didn't response in time during the set-up of the connection or during the break down of it. This state shall be left, when either the manager sets dvbInaConDesiredState to Down(1) or, the NIU enters the Null(1) state.ro Enumeration .1.3.6.1.2.1.10.146.1.6.1.1.3 |
dvbInaIfConDesiredStateDesired state for the connection. The following desired states are possible: down(1), up(3) and, downAlloc(5).rw Enumeration .1.3.6.1.2.1.10.146.1.6.1.1.4 |
dvbInaIfConConnectionTypeSpecifies the kind of connection: fixed rate, contention based, or reservation based. This parameter can be set to a value that is an OR of the following bits: 'conTypeFixedRate(0)' 'conTypeContention(1)' 'conTypeReservation(2)' Default this object is 'conTypeContention(1)'.rw Bits .1.3.6.1.2.1.10.146.1.6.1.1.5 |
dvbInaIfConAccessStatusControls and reflects the status of this row in this table.rw RowStatus (SNMPv2-TC) .1.3.6.1.2.1.10.146.1.6.1.1.6 |
dvbInaIfConEncapsulationThis object indicates the type of encapsulation provided on this connection. This object can have one of the following values: 'directIp(1)', 'ethernetMacBridging(2)', or 'ppp(3)'. By default this parameter is set to 'directIp(1)'.rw Enumeration .1.3.6.1.2.1.10.146.1.6.1.1.7 |
dvbInaIfConAtmDownstreamVCCATM concatenated VPI and VCI Virtual Path Identifiers that is used for downstream OoB transmission.ro Unsigned32 .1.3.6.1.2.1.10.146.1.6.1.1.8 |
dvbInaIfConAtmUpstreamVCCATM concatenated VPI and VCI Virtual Path Identifiers that is used for upstream transmission.ro Unsigned32 .1.3.6.1.2.1.10.146.1.6.1.1.9 |
dvbInaIfConFilterMACAddressSpecifies the 'soft' MPEG MPE MAC address used to filter the data out of the downstream IB transmission. This is found in the Downstream_Multiprotocol_CBD substructure in the Connect Message.rw MacAddress (SNMPv2-TC) .1.3.6.1.2.1.10.146.1.6.1.1.10 |
dvbInaIfConPIDSpecifies the MPEG PID of the elementary stream that carries the data.rw Unsigned32 ( 0..8191 ) .1.3.6.1.2.1.10.146.1.6.1.1.11 |
dvbInaIfConMaxContentionMsgLenThe Maximum_Contention_Access_Message_Length in the Connect Message. This is the maximum length of a message that may be transmitted using contention access. Any message greater than this should use reservation access. The default value should be dvbInaIfMacMaxContentionMsgLen.rw INTEGER ( 1..255 ) UNITS "ATM cells" .1.3.6.1.2.1.10.146.1.6.1.1.12 |
dvbInaIfConMaxReservationMsgLenThis is the maximum length of a message that may be transmitted using a single reservation access. Any message greater than this should be transmitted by making multiple reservation requests. The default value should be dvbInaIfMacMaxReservationMsgLen.rw INTEGER ( 0..255 ) UNITS "ATM cells" .1.3.6.1.2.1.10.146.1.6.1.1.13 |
dvbInaIfConAuxFlagsThe Connection_Control_Field_Aux from the Connect Message Structure. This is used to indicate if the Priority, Downstream flowspec and Session binding objects are used for the connection.ro INTEGER ( 0..255 ) .1.3.6.1.2.1.10.146.1.6.1.1.14 |
dvbInaIfConQosTableContains information about connection quality for DVB-RC MAC connections. Both upstream and downstream quality parameters are found. SEQUENCE OF DvbInaIfConQosEntry .1.3.6.1.2.1.10.146.1.6.2 |
dvbInaIfConQosEntryAn entry in the table is automatically created when a new entry in the connection table connection is created and the INA supports Quality of Service on the MAC layer. You must always create an entry in the Connection table first and this will automatically create an entry in the QoS table. The entries are deleted when the contection table entry is deleted. DvbInaIfConQosEntry .1.3.6.1.2.1.10.146.1.6.2.1 |
dvbInaIfConQosPriorityThe priority of the connection. Connections with low priority field value can be reprovisioned in order to accommodate the requirements of connections with high priority field. Standard data flow applications 0-79 Applications with QoS requirements 80-200 High priority applications 201-255rw INTEGER ( 0..255 ) .1.3.6.1.2.1.10.146.1.6.2.1.1 |
dvbInaIfConQosDsReqMaxPacketSizeA downstream QoS parameter. Defines the requested maximum packet size in the downstream. The parameter can be set either by the managment system, or by the INA according to the NIU resource request. The packet size includes propriety protocols header, transport protocol (UDP/TCP) header, and the IP header. The packet size does not include the Ethernet header.rw Unsigned32 ( 0..65535 ) .1.3.6.1.2.1.10.146.1.6.2.1.2 |
dvbInaIfConQosDsReqBitrateA downstream QoS parameter. Defines requested average bit rate in the downstream. The parameter can be set either by the managment system, or by the INA according to the NIU resource request.rw Unsigned32 ( 0..65535 ) UNITS "bytes/s" .1.3.6.1.2.1.10.146.1.6.2.1.3 |
dvbInaIfConQosDsReqJitterA downstream QoS parameter. Defines the requested maximum allowed jitter in the downstream. The parameter can be set either by the managment system, or by the INA according to the NIU resource request.rw INTEGER ( 0..255 ) UNITS "ms" .1.3.6.1.2.1.10.146.1.6.2.1.4 |
dvbInaIfConQosDsAllocMaxPacketSizeA downstream QoS parameter. This is the actual maximum packet size supported by the INA in the downstream. The packet size includes propriety protocols header, transport protocol (UDP/TCP) header, and the IP header. The packet size does not include the Ethernet header.ro Unsigned32 ( 0..65535 ) .1.3.6.1.2.1.10.146.1.6.2.1.5 |
dvbInaIfConQosDsAllocBitrateA downstream QoS parameter. This is the actual average bit rate supported by the INA in the downstream.ro Unsigned32 ( 0..65535 ) UNITS "bytes/s" .1.3.6.1.2.1.10.146.1.6.2.1.6 |
dvbInaIfConQosDsAllocJitterA downstream QoS parameter. This is the actual maximum jitter supported by the INA in the downstream.ro INTEGER ( 0..255 ) UNITS "ms" .1.3.6.1.2.1.10.146.1.6.2.1.7 |
dvbInaIfConQosUsReqBwAn upstream QoS parameter. The requested bandwidth for the upstream. The parameter can be set either by the managment system, or by the INA according to the NIU resource request.rw Unsigned32 ( 0..16777215 ) UNITS "slots/1200 ms" .1.3.6.1.2.1.10.146.1.6.2.1.8 |
dvbInaIfConQosUsReqMaxDistSlotsAn upstream QoS parameter. The requested maximum distance between slots for the upstream. The parameter can be set either by the managment system, or by the INA according to the NIU resource request.rw Unsigned32 ( 0..65535 ) UNITS "slots" .1.3.6.1.2.1.10.146.1.6.2.1.9 |
dvbInaIfConQosUsReqFrameLengthAn upstream QoS parameter. The requested frame length for the upstream. The parameter can be set either by the managment system, or by the INA according to the NIU resource request.rw Unsigned32 ( 0..65535 ) .1.3.6.1.2.1.10.146.1.6.2.1.10 |
dvbInaIfConQosUsAllocBwAn upstream QoS parameter. The actual allocated bandwidth for the upstream.ro Unsigned32 ( 0..16777215 ) UNITS "slots/1200 ms" .1.3.6.1.2.1.10.146.1.6.2.1.11 |
dvbInaIfConQosUsAllocMaxDistSlotsAn upstream QoS parameter. The allocated distance between slots for the upstream. In case of using a cyclic assignment, this is the parameter sent by the INA in the connect message. In the case of reservation access, this parameter is an average number, calculated by the INA to reflect the actual allocation.ro Unsigned32 ( 0..65535 ) UNITS "slots" .1.3.6.1.2.1.10.146.1.6.2.1.12 |
dvbInaIfConQosUsAllocFrameLengthAn upstream QoS parameter. The allocated frame length for the upstream. In case of using a cyclic assignment, this is the parameter sent by the INA in the connect message. In the case of reservation access, this parameter is an average number, calculated by the INA to reflect the actual allocation.ro Unsigned32 ( 0..65535 ) .1.3.6.1.2.1.10.146.1.6.2.1.13 |
dvbInaIfConQosUsReqFixedRateMethodAn upstream QoS parameter. Request a specific fixed rate slot assignment method to be used. If cyclic then cyclic assignment is used. If slotList then the slot list method is used. The parameter can be set either by the managment system, or by the INA according to the NIU resource request. If the bit Cyclic_Assignment_Needed is set, the NIU requests the cyclic method. Otherwise the slot list method.rw Enumeration .1.3.6.1.2.1.10.146.1.6.2.1.14 |
dvbInaIfConQosUsAllocFixedRateMethodAn upstream QoS parameter. Reflects the actual fixed rate slot assignment method that is used. If cyclic then cyclic assignment is used. If slotList then the slot list method is used.ro Enumeration .1.3.6.1.2.1.10.146.1.6.2.1.15 |
dvbInaIfConSesTableContains information about session binding for DVB-RC MAC connections. SEQUENCE OF DvbInaIfConSesEntry .1.3.6.1.2.1.10.146.1.6.3 |
dvbInaIfConSesEntryAn entry in the table is automatically created when a new entry in the connection table connection is created if the INA and the NIU supports session binding. The entries are deleted when the contection table entry is deleted. DvbInaIfConSesEntry .1.3.6.1.2.1.10.146.1.6.3.1 |
dvbInaIfConSesUsControlControl which fields of the upstream session binding parameters that are used.ro Unsigned32 ( 0..4294967295 ) .1.3.6.1.2.1.10.146.1.6.3.1.1 |
dvbInaIfConSesUsNiuClientSrcIpTypeThe type of the IP source address of the NIU client.ro InetAddressType (INET-ADDRESS-MIB) .1.3.6.1.2.1.10.146.1.6.3.1.2 |
dvbInaIfConSesUsNiuClientSrcIpThe IP source address of the NIU client. Only used if bit 0 of dvbInaIfConSesUsControl is set.ro InetAddress (INET-ADDRESS-MIB) .1.3.6.1.2.1.10.146.1.6.3.1.3 |
dvbInaIfConSesUsNiuClientDstIpTypeThe type of the IP destination address of the NIU client.ro InetAddressType (INET-ADDRESS-MIB) .1.3.6.1.2.1.10.146.1.6.3.1.4 |
dvbInaIfConSesUsNiuClientDstIpThe IP destination address of the NIU client. Only used if bit 1 of dvbInaIfConSesUsControl is set.ro InetAddress (INET-ADDRESS-MIB) .1.3.6.1.2.1.10.146.1.6.3.1.5 |
dvbInaIfConSesUsNiuClientSrcPortThe source port of the NIU client. Only used if bit 2 of dvbInaIfConSesUsControl is set.ro Unsigned32 ( 0..65535 ) .1.3.6.1.2.1.10.146.1.6.3.1.6 |
dvbInaIfConSesUsNiuClientDstPortThe destination port of the NIU client. Only used if bit 3 of dvbInaIfConSesUsControl is set.ro Unsigned32 ( 0..65535 ) .1.3.6.1.2.1.10.146.1.6.3.1.7 |
dvbInaIfConSesUsTransportProtocolThe transport protocol used by the NIU client (UDP/TCP). This is the 8-bit protocol field in the IP header. Only used if bit 4 of dvbInaIfConSesUsControl is set.ro INTEGER ( 0..255 ) .1.3.6.1.2.1.10.146.1.6.3.1.8 |
dvbInaIfConSesUsNiuClientSrcMacThe Ethernet source MAC address of the NIU client. Only used if bit 5 of dvbInaIfConSesUsControl is set.ro MacAddress (SNMPv2-TC) .1.3.6.1.2.1.10.146.1.6.3.1.9 |
dvbInaIfConSesUsNiuClientDstMacThe Ethernet destination MAC address of the NIU client. Only used if bit 6 of dvbInaIfConSesUsControl is set.ro MacAddress (SNMPv2-TC) .1.3.6.1.2.1.10.146.1.6.3.1.10 |
dvbInaIfConSesUsEthernetProtocolThe ethernet protocol, as described in the ethernet header. This is the type field in the Ethernet protocol header. Only used if bit 7 of dvbInaIfConSesUsControl is set.ro Unsigned32 ( 0..65535 ) .1.3.6.1.2.1.10.146.1.6.3.1.11 |
dvbInaIfConSesUsSessionIdThe session_Id, as defined for PPPoE protocol. Only used if bit 8 of dvbInaIfConSesUsControl is set.ro Unsigned32 ( 0..4294967295 ) .1.3.6.1.2.1.10.146.1.6.3.1.12 |
dvbInaIfConSesDsControlControl which fields of the downstream session binding parameters that are used.ro Unsigned32 ( 0..4294967295 ) .1.3.6.1.2.1.10.146.1.6.3.1.13 |
dvbInaIfConSesDsInaClientSrcIpTypeThe type of the IP source address of the INA client.ro InetAddressType (INET-ADDRESS-MIB) .1.3.6.1.2.1.10.146.1.6.3.1.14 |
dvbInaIfConSesDsInaClientSrcIpThe IP source address of the INA client. Only used if bit 0 of dvbInaIfConSesDsControl is set.ro InetAddress (INET-ADDRESS-MIB) .1.3.6.1.2.1.10.146.1.6.3.1.15 |
dvbInaIfConSesDsInaClientDstIpTypeThe type of the IP destination address of the INA client.ro InetAddressType (INET-ADDRESS-MIB) .1.3.6.1.2.1.10.146.1.6.3.1.16 |
dvbInaIfConSesDsInaClientDstIpThe IP destination address of the INA client. Only used if bit 1 of dvbInaIfConSesDsControl is set.ro InetAddress (INET-ADDRESS-MIB) .1.3.6.1.2.1.10.146.1.6.3.1.17 |
dvbInaIfConSesDsInaClientSrcPortThe source port of the INA client. Only used if bit 2 of dvbInaIfConSesDsControl is set.ro Unsigned32 ( 0..65535 ) .1.3.6.1.2.1.10.146.1.6.3.1.18 |
dvbInaIfConSesDsInaClientDstPortThe destination port of the INA client. Only used if bit 3 of dvbInaIfConSesDsControl is set.ro Unsigned32 ( 0..65535 ) .1.3.6.1.2.1.10.146.1.6.3.1.19 |
dvbInaIfConSesDsTransportProtocolThe transport protocol used by the INA client (UDP/TCP). This is the 8-bit protocol field in the IP header. Only used if bit 4 of dvbInaIfConSesDsControl is set.ro INTEGER ( 0..255 ) .1.3.6.1.2.1.10.146.1.6.3.1.20 |
dvbInaIfConSesDsInaClientSrcMacThe Ethernet source MAC address of the INA client. Only used if bit 5 of dvbInaIfConSesDsControl is set.ro MacAddress (SNMPv2-TC) .1.3.6.1.2.1.10.146.1.6.3.1.21 |
dvbInaIfConSesDsInaClientDstMacThe Ethernet destination MAC address of the INA client. Only used if bit 6 of dvbInaIfConSesDsControl is set.ro MacAddress (SNMPv2-TC) .1.3.6.1.2.1.10.146.1.6.3.1.22 |
dvbInaIfConSesDsEthernetProtocolThe ethernet protocol, as described in the ethernet header. This is the type field in the Ethernet protocol header. Only used if bit 7 of dvbInaIfConSesDsControl is set.ro Unsigned32 ( 0..65535 ) .1.3.6.1.2.1.10.146.1.6.3.1.23 |
dvbInaIfConSesDsSessionIdThe session_Id, as defined for PPPoE protocol. Only used if bit 8 of dvbInaIfConSesDsControl is set.ro Unsigned32 ( 0..4294967295 ) .1.3.6.1.2.1.10.146.1.6.3.1.24 |
dvbInaIfConHdrSupTableTable contains information about the header suppression for a connection, indexed trough the Connection ID and the Context ID. SEQUENCE OF DvbInaIfConHdrSupEntry .1.3.6.1.2.1.10.146.1.6.4 |
dvbInaIfConHdrSupEntryAn entry in the table is automatically generated when a new header suppression starts. Or when a reprovisioning is made. An entry is deleted when the connection is deleted. DvbInaIfConHdrSupEntry .1.3.6.1.2.1.10.146.1.6.4.1 |
dvbInaIfConHdrSupContextIdThe context ID for the header suppression session. INTEGER ( 0..127 ) .1.3.6.1.2.1.10.146.1.6.4.1.1 |
dvbInaIfConHdrSupDirectionThe direction for this the header suppression session. Enumeration .1.3.6.1.2.1.10.146.1.6.4.1.2 |
dvbInaIfConHdrSupControlString of bits that control the use of the header suppression. Each of the first 103 bits, indicates if a byte in the header is suppressed or not. Bit 103 is used as an overall suppression enable. If a mask bit is 0, the matching header byte is suppressed. If bit 103 is set, suppression is performed. Bit 103 is the least significant bit in octet 13. See also dvbInaIfConHdrSupHeader.ro OCTET STRING ( SIZE ( 13 )) .1.3.6.1.2.1.10.146.1.6.4.1.3 |
dvbInaIfConHdrSupGenerationThe generation number that is attached to the header fields value.ro Integer32 ( 0..15 ) .1.3.6.1.2.1.10.146.1.6.4.1.4 |
dvbInaIfConHdrSupHeaderLengthThe number of usefull bytes in the suppression header. This is the number of the last zero in the dvbInaIfConHdrSupControl.ro Integer32 ( 0..103 ) .1.3.6.1.2.1.10.146.1.6.4.1.5 |
dvbInaIfConHdrSupHeaderThe header used for header suppression. Both fixed and changing fields together. Only the first dvbInaIfConHdrSupHeaderLength is used.ro OCTET STRING ( SIZE ( 103 )) .1.3.6.1.2.1.10.146.1.6.4.1.6 |
dvbInaIfReprov OBJECT IDENTIFIER .1.3.6.1.2.1.10.146.1.7 |
dvbInaIfReprovSrcNiuTableThe table describes information created on INA 1 for a NIU that is about to be reprovisioned. SEQUENCE OF DvbInaIfReprovSrcNiuEntry .1.3.6.1.2.1.10.146.1.7.1 |
dvbInaIfReprovSrcNiuEntryAn entry in the table is created by the manager when a NIU is about to be reprovisioned. When the reprovisioning is done and the NIU entry is deleted after dvbInaIfNiuLifetime this entry will be deleted too. DvbInaIfReprovSrcNiuEntry .1.3.6.1.2.1.10.146.1.7.1.1 |
dvbInaIfReprovSrcNiuRowAccessStatusControls and reflects the status of this row in this table.rw RowStatus (SNMPv2-TC) .1.3.6.1.2.1.10.146.1.7.1.1.1 |
dvbInaIfReprovSrcNiuCommandControls the reprovisioning on INA 1. When set to reprovStart the actual reporvisioning on INA 1 is initiated with a Reprovisioning Message to the NIU. Everything must be prepared for the reprovisioning when this is done. When read the response will always be reprovIdle.rw Enumeration .1.3.6.1.2.1.10.146.1.7.1.1.2 |
dvbInaIfReprovSrcNiuDsChFrequencyThe centre of the new downstream frequency when the NIU is reprovisioned to INA 2.rw DownFrequency UNITS "hertz" .1.3.6.1.2.1.10.146.1.7.1.1.3 |
dvbInaIfReprovSrcNiuDsChSymbolRateSpecifies the new symbol rate for the Downstream channel when the NIU is reprovisioned.rw DownstreamSymbolrate UNITS "symbol/s" .1.3.6.1.2.1.10.146.1.7.1.1.4 |
dvbInaIfReprovSrcNiuDsChModulationSpecifies the new modulation for the Downstream channel when the NIU is reprovisioned.rw Modulation .1.3.6.1.2.1.10.146.1.7.1.1.5 |
dvbInaIfReprovSrcNiuDsChTypeSpecifies if the new Downstream channel is inband or out-of-band when the NIU is reprovisioned.rw Enumeration .1.3.6.1.2.1.10.146.1.7.1.1.6 |
dvbInaIfReprovSrcNiuUsChFrequencySpecifies the new upstream channel frequency in Hz when the NIU is reprovisoned.rw UpFrequency UNITS "hertz" .1.3.6.1.2.1.10.146.1.7.1.1.7 |
dvbInaIfReprovSrcNiuUsChSymbolRateSpecifies the new upstream channel symbol rate when the NIU is reprovisoned.rw UpstreamSymbolrate .1.3.6.1.2.1.10.146.1.7.1.1.8 |
dvbInaIfReprovSrcNiuUsChModulationSpecifies the new upstream modulation when the NIU is reprovisoned.rw Modulation .1.3.6.1.2.1.10.146.1.7.1.1.9 |
dvbInaIfReprovSrcNiuUsChIdSpecifies the new logical channel number associated with the upstream channel when the NIU is reprovisioned.ro Integer32 ( 0..255 ) .1.3.6.1.2.1.10.146.1.7.1.1.10 |
dvbInaIfReprovDstNiuTableThe table describes information created on INA 2 for a NIU that is about to be reprovisioned. SEQUENCE OF DvbInaIfReprovDstNiuEntry .1.3.6.1.2.1.10.146.1.7.2 |
dvbInaIfReprovDstNiuEntryAn entry in the table is created by the manager when a NIU is about to be reprovisioned. When the reprovisioning is done and the NIU signs on to INA 2 the information is transfered to the NIU table and the entry in this table is deleted automatically. DvbInaIfReprovDstNiuEntry .1.3.6.1.2.1.10.146.1.7.2.1 |
dvbInaIfReprovDstNiuMacAddressA 48-bit value representing the unique MAC address of the NIU to be reprovisioned. This is the index of the table. MacAddress (SNMPv2-TC) .1.3.6.1.2.1.10.146.1.7.2.1.1 |
dvbInaIfReprovDstNiuRowAccessStatusControls and reflects the status of this row in this table.rw RowStatus (SNMPv2-TC) .1.3.6.1.2.1.10.146.1.7.2.1.2 |
dvbInaIfReprovDstNiuCommandControls the reprovisioning on INA 2. When set to reprovPrepare INA 2 will generate the necessary information that needs to be transferred back to INA 1. This includes: New Connection ID's New PID for each connection New downstream VPI/VCI New upstream VPI/VCI New upstream number Furthermore new fixed rate parameters are calculated if one of the new connections are fixed rate. All settings needed to calculate these new parameters must be given before reprovPrepare is set. When set to reprovReceiveNiu this is an indication to INA 2 that the NIU is expected to sign-on now. When read the response will always be reprovIdle.rw Enumeration .1.3.6.1.2.1.10.146.1.7.2.1.3 |
dvbInaIfReprovDstNiuDownIfIndexSpecifies the IfIndex of the downstream channel on which the NIU is tuned after the reprovisioning.rw InterfaceIndexOrZero (IF-MIB) .1.3.6.1.2.1.10.146.1.7.2.1.4 |
dvbInaIfReprovDstNiuUpIfIndexSpecifies the IfIndex of the upstream channel that is used by the NIU after the reprovisioning.rw InterfaceIndexOrZero (IF-MIB) .1.3.6.1.2.1.10.146.1.7.2.1.5 |
dvbInaIfReprovDstNiuLifetimeDefines how long time after the NIU signs off, the NIU entry is removed from the NIU table. An infinite(0) value would mean that the values are stored at least until the next reboot of the INArw Unsigned32 ( 0..4294967295 ) UNITS "s" .1.3.6.1.2.1.10.146.1.7.2.1.6 |
dvbInaIfReprovSrcConTableContains information about DVB-RC MAC connections on INA 1 that is about to be reprovisioned. SEQUENCE OF DvbInaIfReprovSrcConEntry .1.3.6.1.2.1.10.146.1.7.3 |
dvbInaIfReprovSrcConEntryThe entries in the table are created by the manager when a NIU on INA 1 is about to be reprovisioned. After the NIU is reprovisoned the entries are automatically deleted when the corresponding NUI entry are deleted after dvbInaIfNiuLifetime. DvbInaIfReprovSrcConEntry .1.3.6.1.2.1.10.146.1.7.3.1 |
dvbInaIfReprovSrcConRowAccessStatusControls and reflects the status of this row in this table.rw RowStatus (SNMPv2-TC) .1.3.6.1.2.1.10.146.1.7.3.1.1 |
dvbInaIfReprovSrcConConnectionIdNewSpecifies the new value for the connection identifier to be used for this connection after the reprovisioning. The management system must get this value from INA 2.rw Unsigned32 ( 0..4294967295 ) .1.3.6.1.2.1.10.146.1.7.3.1.2 |
dvbInaIfReprovSrcConPIDSpecifies the new MPEG PID of the elementary stream that carries the data after the reprovisioning.rw Unsigned32 ( 0..8191 ) .1.3.6.1.2.1.10.146.1.7.3.1.3 |
dvbInaIfReprovSrcConDsVcATM concatenated VPI and VCI Virtual Path Identifiers that is used for downstream OoB transmission after reprovisioning. The management system must get this value from INA 2.rw Unsigned32 ( 0..16777215 ) .1.3.6.1.2.1.10.146.1.7.3.1.4 |
dvbInaIfReprovSrcConUsVcATM concatenated VPI and VCI Virtual Path Identifiers that is used for upstream transmission after reprovisioning. The management system must get this value from INA 2.rw Unsigned32 ( 0..16777215 ) .1.3.6.1.2.1.10.146.1.7.3.1.5 |
dvbInaIfReprovDstConTableContains information about DVB-RC MAC connections that is about to be reprovisioned to INA 2. SEQUENCE OF DvbInaIfReprovDstConEntry .1.3.6.1.2.1.10.146.1.7.4 |
dvbInaIfReprovDstConEntryThe entries in the table are created by the manager when a NIU is about to be reprovisioned to INA 2. After the NIU has signed on to INA 2, the information in the tables are used to create entries in the normal connection tables. When the entries in the normal tables are made the entries in the reprovisioning table are automatically deleted. DvbInaIfReprovDstConEntry .1.3.6.1.2.1.10.146.1.7.4.1 |
dvbInaIfReprovDstConConnectionIdOldSpecifies the old value for the connection identifier that is used on INA 1. The management system must get this value from INA 1. Unsigned32 ( 0..4294967295 ) .1.3.6.1.2.1.10.146.1.7.4.1.1 |
dvbInaIfReprovDstConRowAccessStatusControls and reflects the status of this row in this table.rw RowStatus (SNMPv2-TC) .1.3.6.1.2.1.10.146.1.7.4.1.2 |
dvbInaIfReprovDstConConnectionIdNewSpecifies the new value for the connection identifier that is used on INA 2. INA 2 creates this value when dvbInaIfReprovDstNiuCommand is set to reprovPrepare.ro Unsigned32 ( 0..4294967295 ) .1.3.6.1.2.1.10.146.1.7.4.1.3 |
dvbInaIfReprovDstConConnectionTypeSpecifies the kind of connection: fixed rate, contention based, or reservation based. This parameter can be set to a value that is an OR of the following bits: 'conTypeFixedRate(0)' 'conTypeContention(1)' 'conTypeReservation(2)' Default this object is 'conTypeContention(1)'.rw Bits .1.3.6.1.2.1.10.146.1.7.4.1.4 |
dvbInaIfReprovDstConEncapsulationThis object indicates the type of encapsulation provided on this connection. This object can have one of the following values: 'directIp(1)', 'ethernetMacBridging(2)', or 'ppp(3)'. By default this parameter is set to 'directIp(1)'.rw Enumeration .1.3.6.1.2.1.10.146.1.7.4.1.5 |
dvbInaIfReprovDstConAtmDownstreamVCCATM concatenated VPI and VCI Virtual Path Identifiers that is used for downstream OoB transmission. INA 2 creates this value when dvbInaIfReprovDstNiuCommand is set to reprovPrepare.ro Unsigned32 .1.3.6.1.2.1.10.146.1.7.4.1.6 |
dvbInaIfReprovDstConAtmUpstreamVCCATM concatenated VPI and VCI Virtual Path Identifiers that is used for upstream transmission. INA 2 creates this value when dvbInaIfReprovDstNiuCommand is set to reprovPrepare.ro Unsigned32 .1.3.6.1.2.1.10.146.1.7.4.1.7 |
dvbInaIfReprovDstConFilterMACAddressSpecifies the 'soft' MPEG MPE MAC address used to filter the data out of the downstream IB transmission. This is found in the Downstream_Multiprotocol_CBD substructure in the Connect Message.rw MacAddress (SNMPv2-TC) .1.3.6.1.2.1.10.146.1.7.4.1.8 |
dvbInaIfReprovDstConPIDSpecifies the MPEG PID of the elementary stream that carries the data. INA 2 creates this value when dvbInaIfReprovDstNiuCommand is set to reprovPrepare.ro Unsigned32 ( 0..8191 ) .1.3.6.1.2.1.10.146.1.7.4.1.9 |
dvbInaIfReprovDstConMaxContentionMsgLenThe Maximum_Contention_Access_Message_Length in the Connect Message. This is the maximum length of a message that may be transmitted using contention access. Any message greater than this should use reservation access. The default value should be dvbInaIfMacMaxContentionMsgLen.rw INTEGER ( 1..255 ) UNITS "ATM cells" .1.3.6.1.2.1.10.146.1.7.4.1.10 |
dvbInaIfReprovDstConMaxReservationMsgLenThis is the maximum length of a message that may be transmitted using a single reservation access. Any message greater than this should be transmitted by making multiple reservation requests. The default value should be dvbInaIfMacMaxReservationMsgLen.rw INTEGER ( 0..255 ) UNITS "ATM cells" .1.3.6.1.2.1.10.146.1.7.4.1.11 |
dvbInaIfReprovDstConAuxFlagsThe Connection_Control_Field_Aux from the Connect Message Structure. This is used to indicate if the Priority, Downstream flowspec and Session binding objects are used for the connection.ro INTEGER ( 0..255 ) .1.3.6.1.2.1.10.146.1.7.4.1.12 |
dvbInaIfReprovDstConSesTableContains information about DVB-RC MAC connections that is about to be reprovisioned to INA 2. SEQUENCE OF DvbInaIfReprovDstConSesEntry .1.3.6.1.2.1.10.146.1.7.5 |
dvbInaIfReprovDstConSesEntryThe entries in the table are created automatically when an entry in the dvbInaIfReprovDstConTable is created and the INA support session binding. You must always create an entry in the dvbInaIfReprovDstConTable first and this will automatically create an entry in the dvbInaIfReprovDstConSesTable table. After the NIU has signed on to INA 2, the information in the table are used to create entries in the normal connection tables. When the entries in the normal tables are made the entries in the reprovisioning table are automatically deleted. DvbInaIfReprovDstConSesEntry .1.3.6.1.2.1.10.146.1.7.5.1 |
dvbInaIfReprovDstConSesUsControlControl which fields of the upstream session binding parameters that are used.rw Unsigned32 ( 0..4294967295 ) .1.3.6.1.2.1.10.146.1.7.5.1.1 |
dvbInaIfReprovDstConSesUsNiuClientSrcIpTypeThe type of the IP source address of the NIU client.rw InetAddressType (INET-ADDRESS-MIB) .1.3.6.1.2.1.10.146.1.7.5.1.2 |
dvbInaIfReprovDstConSesUsNiuClientSrcIpThe IP source address of the NIU client. Only used if bit 0 of dvbInaIfReprovDstConSesUsControl is set.rw InetAddress (INET-ADDRESS-MIB) .1.3.6.1.2.1.10.146.1.7.5.1.3 |
dvbInaIfReprovDstConSesUsNiuClientDstIpTypeThe type of the IP destination address of the NIU client.rw InetAddressType (INET-ADDRESS-MIB) .1.3.6.1.2.1.10.146.1.7.5.1.4 |
dvbInaIfReprovDstConSesUsNiuClientDstIpThe IP destination address of the NIU client. Only used if bit 1 of dvbInaIfReprovDstConSesUsControl is set.rw InetAddress (INET-ADDRESS-MIB) .1.3.6.1.2.1.10.146.1.7.5.1.5 |
dvbInaIfReprovDstConSesUsNiuClientSrcPortThe source port of the NIU client. Only used if bit 2 of dvbInaIfReprovDstConSesUsControl is set.rw Unsigned32 ( 0..65535 ) .1.3.6.1.2.1.10.146.1.7.5.1.6 |
dvbInaIfReprovDstConSesUsNiuClientDstPortThe destination port of the NIU client. Only used if bit 3 of dvbInaIfReprovDstConSesUsControl is set.rw Unsigned32 ( 0..65535 ) .1.3.6.1.2.1.10.146.1.7.5.1.7 |
dvbInaIfReprovDstConSesUsTransportProtocolThe transport protocol used by the NIU client (UDP/TCP). This is the 8-bit protocol field in the IP header. Only used if bit 4 of dvbInaIfReprovDstConSesUsControl is set.rw INTEGER ( 0..255 ) .1.3.6.1.2.1.10.146.1.7.5.1.8 |
dvbInaIfReprovDstConSesUsNiuClientSrcMacThe Ethernet source MAC address of the NIU client. Only used if bit 5 of dvbInaIfReprovDstConSesUsControl is set.rw MacAddress (SNMPv2-TC) .1.3.6.1.2.1.10.146.1.7.5.1.9 |
dvbInaIfReprovDstConSesUsNiuClientDstMacThe Ethernet destination MAC address of the NIU client. Only used if bit 6 of dvbInaIfReprovDstConSesUsControl is set.rw MacAddress (SNMPv2-TC) .1.3.6.1.2.1.10.146.1.7.5.1.10 |
dvbInaIfReprovDstConSesUsEthernetProtocolThe ethernet protocol, as described in the ethernet header. This is the type field in the Ethernet protocol header. Only used if bit 7 of dvbInaIfReprovDstConSesUsControl is set.rw Unsigned32 ( 0..65535 ) .1.3.6.1.2.1.10.146.1.7.5.1.11 |
dvbInaIfReprovDstConSesUsSessionIdThe session_Id, as defined for PPPoE protocol. Only used if bit 8 of dvbInaIfReprovDstConSesUsControl is set.rw Unsigned32 ( 0..4294967295 ) .1.3.6.1.2.1.10.146.1.7.5.1.12 |
dvbInaIfReprovDstConSesDsControlControl which fields of the downstream session binding parameters that are used.rw Unsigned32 ( 0..4294967295 ) .1.3.6.1.2.1.10.146.1.7.5.1.13 |
dvbInaIfReprovDstConSesDsInaClientSrcIpTypeThe type of the IP source address of the INA client.rw InetAddressType (INET-ADDRESS-MIB) .1.3.6.1.2.1.10.146.1.7.5.1.14 |
dvbInaIfReprovDstConSesDsInaClientSrcIpThe IP source address of the INA client. Only used if bit 0 of dvbInaIfReprovDstConSesDsControl is set.rw InetAddress (INET-ADDRESS-MIB) .1.3.6.1.2.1.10.146.1.7.5.1.15 |
dvbInaIfReprovDstConSesDsInaClientDstIpTypeThe type of the IP destination address of the INA client.rw InetAddressType (INET-ADDRESS-MIB) .1.3.6.1.2.1.10.146.1.7.5.1.16 |
dvbInaIfReprovDstConSesDsInaClientDstIpThe IP destination address of the INA client. Only used if bit 1 of dvbInaIfReprovDstConSesDsControl is set.rw InetAddress (INET-ADDRESS-MIB) .1.3.6.1.2.1.10.146.1.7.5.1.17 |
dvbInaIfReprovDstConSesDsInaClientSrcPortThe source port of the INA client. Only used if bit 2 of dvbInaIfReprovDstConSesDsControl is set.rw Unsigned32 ( 0..65535 ) .1.3.6.1.2.1.10.146.1.7.5.1.18 |
dvbInaIfReprovDstConSesDsInaClientDstPortThe destination port of the INA client. Only used if bit 3 of dvbInaIfReprovDstConSesDsControl is set.rw Unsigned32 ( 0..65535 ) .1.3.6.1.2.1.10.146.1.7.5.1.19 |
dvbInaIfReprovDstConSesDsTransportProtocolThe transport protocol used by the INA client (UDP/TCP). This is the 8-bit protocol field in the IP header. Only used if bit 4 of dvbInaIfReprovDstConSesDsControl is set.rw INTEGER ( 0..255 ) .1.3.6.1.2.1.10.146.1.7.5.1.20 |
dvbInaIfReprovDstConSesDsInaClientSrcMacThe Ethernet source MAC address of the INA client. Only used if bit 5 of dvbInaIfReprovDstConSesDsControl is set.rw MacAddress (SNMPv2-TC) .1.3.6.1.2.1.10.146.1.7.5.1.21 |
dvbInaIfReprovDstConSesDsInaClientDstMacThe Ethernet destination MAC address of the INA client. Only used if bit 6 of dvbInaIfReprovDstConSesDsControl is set.rw MacAddress (SNMPv2-TC) .1.3.6.1.2.1.10.146.1.7.5.1.22 |
dvbInaIfReprovDstConSesDsEthernetProtocolThe ethernet protocol, as described in the ethernet header. This is the type field in the Ethernet protocol header. Only used if bit 7 of dvbInaIfReprovDstConSesDsControl is set.rw Unsigned32 ( 0..65535 ) .1.3.6.1.2.1.10.146.1.7.5.1.23 |
dvbInaIfReprovDstConSesDsSessionIdThe session_Id, as defined for PPPoE protocol. Only used if bit 8 of dvbInaIfReprovDstConSesDsControl is set.rw Unsigned32 ( 0..4294967295 ) .1.3.6.1.2.1.10.146.1.7.5.1.24 |
dvbInaIfReprovDstConHdrSupTableContains information about DVB-RC MAC connections that is about to be reprovisioned to INA 2. SEQUENCE OF DvbInaIfReprovDstConHdrSupEntry .1.3.6.1.2.1.10.146.1.7.6 |
dvbInaIfReprovDstConHdrSupEntryThe entries in the table are created by the manager when a NIU is about to be reprovisioned to INA 2. After the NIU has signed on to INA 2, the information in the tables are used to create entries in the normal connection tables. When the entries in the normal tables are made the entries in the reprovisioning table are automatically deleted. DvbInaIfReprovDstConHdrSupEntry .1.3.6.1.2.1.10.146.1.7.6.1 |
dvbInaIfReprovDstConHdrSupContextIdThe context ID for the header suppression session. INTEGER ( 0..127 ) .1.3.6.1.2.1.10.146.1.7.6.1.1 |
dvbInaIfReprovDstConHdrSupDirectionThe direction for this the header suppression session. Enumeration .1.3.6.1.2.1.10.146.1.7.6.1.2 |
dvbInaIfReprovDstConHdrSupRowAccessStatusControls and reflects the status of this row in this table.rw RowStatus (SNMPv2-TC) .1.3.6.1.2.1.10.146.1.7.6.1.3 |
dvbInaIfReprovDstConHdrSupControlString of bits that control the use of the header suppression. Each of the fisrt 103 bits, indicates if a byte in the header is suppressed or not. Bit 103 is used as an overall suppression enable. If a mask bit is 0, the matching header byte is suppressed. If bit 103 is set, suppression is performed. Bit 103 is the least significant bit in octet 13. See also dvbInaIfReprovDstConHdrSupHeader.ro OCTET STRING ( SIZE ( 13 )) .1.3.6.1.2.1.10.146.1.7.6.1.4 |
dvbInaIfReprovDstConHdrSupGenerationThe generation number that is attached to the header fields value.ro Integer32 ( 0..15 ) .1.3.6.1.2.1.10.146.1.7.6.1.5 |
dvbInaIfReprovDstConHdrSupHeaderLengthThe number of usefull bytes in the suppression header. This is the number of the last zero in the dvbInaIfReprovDstConHdrSupControl.ro Integer32 ( 0..103 ) .1.3.6.1.2.1.10.146.1.7.6.1.6 |
dvbInaIfReprovDstConHdrSupHeaderThe header used for header suppression. Both fixed and changing fields together. Only the first dvbInaIfReprovDstConHdrSupHeaderLength is used.ro OCTET STRING ( SIZE ( 103 )) .1.3.6.1.2.1.10.146.1.7.6.1.7 |
dvbInaIfReprovDstConQosTableContains information about DVB-RC MAC connections that is about to be reprovisioned to INA 2. SEQUENCE OF DvbInaIfReprovDstConQosEntry .1.3.6.1.2.1.10.146.1.7.7 |
dvbInaIfReprovDstConQosEntryThe entries in the table are created automatically when an entry in the dvbInaIfReprovDstConTable is created and the INA support QoS settings. After the NIU has signed on to INA 2, the information in the tables are used to create entries in the normal connection tables. When the entries in the normal tables are made the entries in the reprovisioning table are automatically deleted. DvbInaIfReprovDstConQosEntry .1.3.6.1.2.1.10.146.1.7.7.1 |
dvbInaIfReprovDstConQosPriorityThe priority of the connection. Connections with low priority field value can be reprovisioned in order to accommodate the requirements of connections with high priority field. Standard data flow applications 0-79 Applications with QoS requirements 80-200 High priority applications 201-255rw INTEGER ( 0..255 ) .1.3.6.1.2.1.10.146.1.7.7.1.1 |
dvbInaIfReprovDstConQosDsReqMaxPacketSizeA downstream QoS parameter. Defines the requested maximum packet size in the downstream. The parameter can be set either by the managment system, or by the INA according to the NIU resource request. The packet size includes propriety protocols header, transport protocol (UDP/TCP) header, and the IP header. The packet size does not include the Ethernet header.rw Unsigned32 ( 0..65535 ) .1.3.6.1.2.1.10.146.1.7.7.1.2 |
dvbInaIfReprovDstConQosDsReqBitrateA downstream QoS parameter. Defines requested average bit rate in the downstream.rw Unsigned32 ( 0..65535 ) UNITS "bytes/s" .1.3.6.1.2.1.10.146.1.7.7.1.3 |
dvbInaIfReprovDstConQosDsReqJitterA downstream QoS parameter. Defines the requested maximum allowed jitter in the downstream.rw INTEGER ( 0..255 ) UNITS "ms" .1.3.6.1.2.1.10.146.1.7.7.1.4 |
dvbInaIfReprovDstConQosUsReqBwAn upstream QoS parameter. The requested bandwidth for the upstream.rw Unsigned32 ( 0..16777215 ) UNITS "slots/1200 ms" .1.3.6.1.2.1.10.146.1.7.7.1.5 |
dvbInaIfReprovDstConQosUsReqMaxDistSlotsAn upstream QoS parameter. The requested maximum distance between slots for the upstream.rw Unsigned32 ( 0..65535 ) UNITS "slots" .1.3.6.1.2.1.10.146.1.7.7.1.6 |
dvbInaIfReprovDstConQosUsReqFrameLengthAn upstream QoS parameter. The requested frame length for the upstream.rw Unsigned32 ( 0..65535 ) .1.3.6.1.2.1.10.146.1.7.7.1.7 |
dvbInaIfReprovDstConQosUsReqFixedRateMethodAn upstream QoS parameter. Request a specific fixed rate slot assignment method to be used. If cyclic then cyclic assignment is used. If slotList then the slot list method is used.rw Enumeration .1.3.6.1.2.1.10.146.1.7.7.1.8 |
dvbInaIfMIBConform OBJECT IDENTIFIER .1.3.6.1.2.1.10.146.2 |
dvbInaIfCompliances OBJECT IDENTIFIER .1.3.6.1.2.1.10.146.2.1 |
dvbInaIfComplianceThe compliance statement for EuroModem INAs which implement the DVB-CABLE-INA-IF-MIB MIB. An implementation only has to support IPv4 addresses to be compliant. Unknown .1.3.6.1.2.1.10.146.2.1.1 |
dvbInaIfGroups OBJECT IDENTIFIER .1.3.6.1.2.1.10.146.2.2 |
dvbInaIfMacGroupA collection of objects providing capabilities and statistics for the MAC layer. Unknown .1.3.6.1.2.1.10.146.2.2.1 |
dvbInaIfProvisionGroup Unknown .1.3.6.1.2.1.10.146.2.2.2 |
dvbInaIfDsChGroup Unknown .1.3.6.1.2.1.10.146.2.2.3 |
dvbInaIfUsChGroup Unknown .1.3.6.1.2.1.10.146.2.2.4 |
dvbInaIfNiuGroup Unknown .1.3.6.1.2.1.10.146.2.2.5 |
dvbInaIfConnectionGroup Unknown .1.3.6.1.2.1.10.146.2.2.6 |
dvbInaIfConQosGroup Unknown .1.3.6.1.2.1.10.146.2.2.7 |
dvbInaIfConSesGroup Unknown .1.3.6.1.2.1.10.146.2.2.8 |
dvbInaIfConHdrSupGroup Unknown .1.3.6.1.2.1.10.146.2.2.9 |
dvbInaIfReprovSrcNiuGroup Unknown .1.3.6.1.2.1.10.146.2.2.10 |
dvbInaIfReprovDstNiuGroup Unknown .1.3.6.1.2.1.10.146.2.2.11 |
dvbInaIfReprovSrcConGroup Unknown .1.3.6.1.2.1.10.146.2.2.12 |
dvbInaIfReprovDstConGroup Unknown .1.3.6.1.2.1.10.146.2.2.13 |
dvbInaIfReprovDstConSesGroup Unknown .1.3.6.1.2.1.10.146.2.2.14 |
dvbInaIfReprovDstConHdrSupGroup Unknown .1.3.6.1.2.1.10.146.2.2.15 |
dvbInaIfReprovDstConQosGroup Unknown .1.3.6.1.2.1.10.146.2.2.16 |