DV2-MIB
Detailed view of the defined objects, syntax rules, and hierarchical paths.
2010
Objects
Active
Status
4
Dependencies
Imported Objects
Objects
2010 total| Object Name |
|---|
netcomm OBJECT IDENTIFIER .1.3.6.1.4.1.251 |
RFC-1215 Unknown .1.3.6.1.4.1.251 |
products OBJECT IDENTIFIER .1.3.6.1.4.1.251.1 |
dv2 OBJECT IDENTIFIER .1.3.6.1.4.1.251.1.1 |
dv2MessageThis is used to send an arbitary text string to the NMS. TRAP-TYPE .1.3.6.1.4.1.251.1.1.0.1 |
slotChangedThis is sent when a slot changes state. TRAP-TYPE .1.3.6.1.4.1.251.1.1.0.2 |
linkChangedThis is sent when a link changes state. TRAP-TYPE .1.3.6.1.4.1.251.1.1.0.3 |
psuChangedThis is sent when a power supply changes state. TRAP-TYPE .1.3.6.1.4.1.251.1.1.0.4 |
configChangedThis is sent when <config.cfg> has changed. TRAP-TYPE .1.3.6.1.4.1.251.1.1.0.5 |
reset040This is sent when a the master processor is reset by operator TRAP-TYPE .1.3.6.1.4.1.251.1.1.0.22 |
badPasswordThis is sent when a user enters a bad password TRAP-TYPE .1.3.6.1.4.1.251.1.1.0.23 |
billingRecFailCould not create billing record TRAP-TYPE .1.3.6.1.4.1.251.1.1.0.26 |
clockAlarmChange in system clock alarm state: declare or clear minor/major alarms,
describe error and location, includes primary/secondary clock locations and
the active clock reference TRAP-TYPE .1.3.6.1.4.1.251.1.1.0.27 |
spvcInitCall successfully established TRAP-TYPE .1.3.6.1.4.1.251.1.1.0.28 |
spvcFailCall attempt failed TRAP-TYPE .1.3.6.1.4.1.251.1.1.0.29 |
spvcCallClrCall cleared after established TRAP-TYPE .1.3.6.1.4.1.251.1.1.0.30 |
spvcCallResetCall reset after established TRAP-TYPE .1.3.6.1.4.1.251.1.1.0.31 |
spvcRetryExceededCall attempts exceeded retry limit TRAP-TYPE .1.3.6.1.4.1.251.1.1.0.33 |
mainInServThis is sent when the Main Slot 0 Controller goes into service TRAP-TYPE .1.3.6.1.4.1.251.1.1.0.76 |
standbyInServThis is sent when the Standby Slot 0 Controller goes into service TRAP-TYPE .1.3.6.1.4.1.251.1.1.0.77 |
bill25pstfullThis is sent when billing table is 25% full. TRAP-TYPE .1.3.6.1.4.1.251.1.1.0.78 |
bill75pstfullThis is sent when billing table is 75% full. TRAP-TYPE .1.3.6.1.4.1.251.1.1.0.79 |
restart040This is sent when the master processor has been restarted by
the 68302 processor. TRAP-TYPE .1.3.6.1.4.1.251.1.1.0.80 |
alcTxErrorThis is sent after master processor has been reset due to
ALC-87 Transmitter Error. TRAP-TYPE .1.3.6.1.4.1.251.1.1.0.81 |
lim-faultConfigured LIM type does not match the LIM in slot TRAP-TYPE .1.3.6.1.4.1.251.1.1.0.91 |
lim-operLIM operational TRAP-TYPE .1.3.6.1.4.1.251.1.1.0.92 |
psuAbsentPSU Absent detected TRAP-TYPE .1.3.6.1.4.1.251.1.1.0.93 |
psuPresentPSU Presence detected TRAP-TYPE .1.3.6.1.4.1.251.1.1.0.94 |
switchFabricSwapSwitch Fabric Redundant Swap TRAP-TYPE .1.3.6.1.4.1.251.1.1.0.95 |
internalResetThis is sent after the software has detected an internal
error and restarted itself. TRAP-TYPE .1.3.6.1.4.1.251.1.1.0.106 |
aal1FaultThis is sent when an AAL1 fault has occurred. TRAP-TYPE .1.3.6.1.4.1.251.1.1.0.107 |
aal1ClearThis is sent when an AAL1 fault has been cleared. TRAP-TYPE .1.3.6.1.4.1.251.1.1.0.108 |
ds1LOSLoss of Signal alarm TRAP-TYPE .1.3.6.1.4.1.251.1.1.0.109 |
ds1LOFLoss of Frame alarm TRAP-TYPE .1.3.6.1.4.1.251.1.1.0.110 |
ds1AISAIS alarm TRAP-TYPE .1.3.6.1.4.1.251.1.1.0.111 |
ds1YellowYellow alarm TRAP-TYPE .1.3.6.1.4.1.251.1.1.0.112 |
ds1ExBERExcessive Bit Error Rate Alarm TRAP-TYPE .1.3.6.1.4.1.251.1.1.0.113 |
ds1v2LOSLoss of Signal alarm TRAP-TYPE .1.3.6.1.4.1.251.1.1.0.114 |
ds1v2LOFLoss of Frame alarm TRAP-TYPE .1.3.6.1.4.1.251.1.1.0.115 |
ds1v2AISAIS alarm TRAP-TYPE .1.3.6.1.4.1.251.1.1.0.116 |
ds1v2YellowYellow alarm TRAP-TYPE .1.3.6.1.4.1.251.1.1.0.117 |
ds1v2ExBERExcessive Bit Error Rate Alarm TRAP-TYPE .1.3.6.1.4.1.251.1.1.0.118 |
ds3LOSLoss of Signal alarm TRAP-TYPE .1.3.6.1.4.1.251.1.1.0.119 |
ds3V2LOSLoss of Signal alarm TRAP-TYPE .1.3.6.1.4.1.251.1.1.0.120 |
ds3LOFLoss of Frame alarm TRAP-TYPE .1.3.6.1.4.1.251.1.1.0.121 |
ds3AISAIS alarm TRAP-TYPE .1.3.6.1.4.1.251.1.1.0.122 |
ds3YellowYellow alarm TRAP-TYPE .1.3.6.1.4.1.251.1.1.0.123 |
ds3ExBERExcessive Bit Error Rate Alarm TRAP-TYPE .1.3.6.1.4.1.251.1.1.0.124 |
ds3FEFrmrDifReceived frame format is different than configured frame format TRAP-TYPE .1.3.6.1.4.1.251.1.1.0.125 |
e1LOSLoss of Signal alarm TRAP-TYPE .1.3.6.1.4.1.251.1.1.0.126 |
e1LOFLoss of Frame alarm TRAP-TYPE .1.3.6.1.4.1.251.1.1.0.127 |
e1AISAIS alarm TRAP-TYPE .1.3.6.1.4.1.251.1.1.0.128 |
e1YellowYellow alarm TRAP-TYPE .1.3.6.1.4.1.251.1.1.0.129 |
e1ExBERExcessive Bit Error Rate Alarm TRAP-TYPE .1.3.6.1.4.1.251.1.1.0.130 |
e3LOSLoss of Signal alarm TRAP-TYPE .1.3.6.1.4.1.251.1.1.0.131 |
e3LOFLoss of Frame alarm TRAP-TYPE .1.3.6.1.4.1.251.1.1.0.132 |
e3AISAIS alarm TRAP-TYPE .1.3.6.1.4.1.251.1.1.0.133 |
e3YellowYellow alarm TRAP-TYPE .1.3.6.1.4.1.251.1.1.0.134 |
e3ExBERExcessive Bit Error Rate Alarm TRAP-TYPE .1.3.6.1.4.1.251.1.1.0.135 |
locdLoss Of Cell Delineation TRAP-TYPE .1.3.6.1.4.1.251.1.1.0.136 |
plcpYellowPLCP yellow alarm TRAP-TYPE .1.3.6.1.4.1.251.1.1.0.137 |
plcpLOFPLCP Loss of Frame alarm TRAP-TYPE .1.3.6.1.4.1.251.1.1.0.138 |
sdhLOSSONET/SDH Loss of Signal TRAP-TYPE .1.3.6.1.4.1.251.1.1.0.139 |
sdhLOFSONET/SDH Loss of Frame TRAP-TYPE .1.3.6.1.4.1.251.1.1.0.140 |
sdhLineAISSONET/SDH Line AIS failure TRAP-TYPE .1.3.6.1.4.1.251.1.1.0.141 |
sdhPathAISSONET/SDH Path AIS failure TRAP-TYPE .1.3.6.1.4.1.251.1.1.0.142 |
sdhLOPSONET/SDH Loss of Pointer TRAP-TYPE .1.3.6.1.4.1.251.1.1.0.143 |
sdhPLMSONET/SDH Path Label Mismatch TRAP-TYPE .1.3.6.1.4.1.251.1.1.0.144 |
sdhLineYellowSONET/SDH Line FERF failure TRAP-TYPE .1.3.6.1.4.1.251.1.1.0.145 |
sdhPathYellowSONET/SDH Path Yellow failure TRAP-TYPE .1.3.6.1.4.1.251.1.1.0.146 |
sdhExBERSONET/SDH Excessive Bit Error Rate TRAP-TYPE .1.3.6.1.4.1.251.1.1.0.147 |
clockActiveRefCurrent Active Reference TRAP-TYPE .1.3.6.1.4.1.251.1.1.0.148 |
outOfResourceLink cell rate is not sufficient for established connections TRAP-TYPE .1.3.6.1.4.1.251.1.1.0.149 |
hssiLOSHSSI Loss of Signal TRAP-TYPE .1.3.6.1.4.1.251.1.1.0.150 |
hssiDTEReadyDTE is Ready TRAP-TYPE .1.3.6.1.4.1.251.1.1.0.151 |
hssiDCEReadyDCE is Ready TRAP-TYPE .1.3.6.1.4.1.251.1.1.0.152 |
hssiDTENotReadyDTE is not Ready TRAP-TYPE .1.3.6.1.4.1.251.1.1.0.153 |
hssiDCENotReadyDCE is not Ready TRAP-TYPE .1.3.6.1.4.1.251.1.1.0.154 |
userstatus1 TRAP-TYPE .1.3.6.1.4.1.251.1.1.0.155 |
userstatus2 TRAP-TYPE .1.3.6.1.4.1.251.1.1.0.156 |
pntmoperSent when Primary NTM card operational status changes TRAP-TYPE .1.3.6.1.4.1.251.1.1.0.157 |
sntmoperSent when Secondary NTM card operational status changes TRAP-TYPE .1.3.6.1.4.1.251.1.1.0.158 |
pntmoscstatusSent when Primary NTM card oscillator status changes TRAP-TYPE .1.3.6.1.4.1.251.1.1.0.159 |
sntmoscstatusSent when secondary NTM card oscillator status changes TRAP-TYPE .1.3.6.1.4.1.251.1.1.0.160 |
pbitslineokSent when Primary NTM card BITS line status changes TRAP-TYPE .1.3.6.1.4.1.251.1.1.0.161 |
sbitslineokSent when secondary NTM card BITS line status changes TRAP-TYPE .1.3.6.1.4.1.251.1.1.0.162 |
svcHalfConnectSVC half connect detected TRAP-TYPE .1.3.6.1.4.1.251.1.1.0.163 |
duplicateIpAddrSent When a duplicate IP address is detected. TRAP-TYPE .1.3.6.1.4.1.251.1.1.0.164 |
svcQsaalResetSent when SAP is reset TRAP-TYPE .1.3.6.1.4.1.251.1.1.0.165 |
svcQsaalUpDownSent when SAP transitions between Up and Down TRAP-TYPE .1.3.6.1.4.1.251.1.1.0.166 |
svcT309ExpirySent when T309 timer expired and calls exist on a SAP TRAP-TYPE .1.3.6.1.4.1.251.1.1.0.167 |
j2LOSLoss of Signal alarm TRAP-TYPE .1.3.6.1.4.1.251.1.1.0.168 |
j2LOFLoss of Frame alarm TRAP-TYPE .1.3.6.1.4.1.251.1.1.0.169 |
j2AISAIS alarm TRAP-TYPE .1.3.6.1.4.1.251.1.1.0.170 |
j2RAIRAI alarm TRAP-TYPE .1.3.6.1.4.1.251.1.1.0.171 |
scfLOSLoss of Signal alarm TRAP-TYPE .1.3.6.1.4.1.251.1.1.0.172 |
routeLoadFaildef.rtb file load failure TRAP-TYPE .1.3.6.1.4.1.251.1.1.0.173 |
dTLLoadFaildtl.bin file load failure TRAP-TYPE .1.3.6.1.4.1.251.1.1.0.174 |
redunNotAvailThis is sent when the Redundant Slot 0 Controller is not available TRAP-TYPE .1.3.6.1.4.1.251.1.1.0.175 |
redunAvailThis is sent when the Redundant Slot 0 Controller is available TRAP-TYPE .1.3.6.1.4.1.251.1.1.0.176 |
dQ7-errorThis trap is sent when edos discovers a DQ7 error in flash TRAP-TYPE .1.3.6.1.4.1.251.1.1.0.177 |
oamVcaRcvAIS-RDIThis trap is generated when an AIS or RDI is received on VCa port TRAP-TYPE .1.3.6.1.4.1.251.1.1.0.178 |
oamVcbRcvAIS-RDIThis trap is generated when an AIS or RDI is received on VCb port TRAP-TYPE .1.3.6.1.4.1.251.1.1.0.179 |
dv2System OBJECT IDENTIFIER .1.3.6.1.4.1.251.1.1.1 |
sysMemEndThe current end of run-time allocated memory.ro Hex .1.3.6.1.4.1.251.1.1.1.1 |
sysInitialMemBinitial number of memory items.ro INTEGER .1.3.6.1.4.1.251.1.1.1.4 |
sysCurrentMemBCurrent number of memory items.ro INTEGER .1.3.6.1.4.1.251.1.1.1.5 |
sysInitialSemaInitial number of semaphores.ro INTEGER .1.3.6.1.4.1.251.1.1.1.6 |
sysCurrentSemaCurrent number of semaphores.ro INTEGER .1.3.6.1.4.1.251.1.1.1.7 |
sysInitialQItemsInitial number of queue items.ro INTEGER .1.3.6.1.4.1.251.1.1.1.8 |
sysCurrentQItemsCurrent number of queue items.ro INTEGER .1.3.6.1.4.1.251.1.1.1.9 |
sysInitialQsInitial number of queues.ro INTEGER .1.3.6.1.4.1.251.1.1.1.10 |
sysCurrentQsCurrent number of queues.ro INTEGER .1.3.6.1.4.1.251.1.1.1.11 |
sysInitialPortsInitial number of ports.ro INTEGER .1.3.6.1.4.1.251.1.1.1.12 |
sysCurrentPortsCurrent number of ports.ro INTEGER .1.3.6.1.4.1.251.1.1.1.13 |
sysDefaultCellModeThis flag indicates whether the cell interface is operating in default mode. If yes(2) then this indicates that the daughter card processor is not running its correct code.ro Enumeration .1.3.6.1.4.1.251.1.1.1.14 |
sysLinkTableThis table contains information about each link on this slot controller. SEQUENCE OF SysLinkEntry .1.3.6.1.4.1.251.1.1.1.15 |
sysLinkEntry SysLinkEntry .1.3.6.1.4.1.251.1.1.1.15.1 |
sysLkLinkNoThe link number on the slotro INTEGER .1.3.6.1.4.1.251.1.1.1.15.1.1 |
sysLkKillLinkSet to restart(2) to kill this linkrw Enumeration .1.3.6.1.4.1.251.1.1.1.15.1.2 |
sysLkStateStatus of the linkro Enumeration .1.3.6.1.4.1.251.1.1.1.15.1.3 |
sysLkTxCellsNumber of cells sent from linkro Counter .1.3.6.1.4.1.251.1.1.1.15.1.4 |
sysLkRxCellsNumber of cells received to linkro Counter .1.3.6.1.4.1.251.1.1.1.15.1.5 |
sysLkTxRateCells per second sent from linkro Gauge .1.3.6.1.4.1.251.1.1.1.15.1.6 |
sysLkRxRateCells per second received to linkro Gauge .1.3.6.1.4.1.251.1.1.1.15.1.7 |
sysLkTxMaxRateMaximum cells per second transmitted from linkro Gauge .1.3.6.1.4.1.251.1.1.1.15.1.8 |
sysLkRxMaxRateMaximum cells per second received to linkro Gauge .1.3.6.1.4.1.251.1.1.1.15.1.9 |
sysLkResetStatsSet to yes(2) to reset the link statisticsrw Enumeration .1.3.6.1.4.1.251.1.1.1.15.1.10 |
sysLkClockSrcThis specifies where the link obtains its clockrw Enumeration .1.3.6.1.4.1.251.1.1.1.15.1.11 |
sysLkResetResrcSet to yes(2) to reset the link resourcesrw Enumeration .1.3.6.1.4.1.251.1.1.1.15.1.12 |
sysLKEgCLPThresholdTransmit CLP1 thresholdrw INTEGER .1.3.6.1.4.1.251.1.1.1.15.1.13 |
sysLKIgCLPThresholdReceive CLP1 thresholdrw INTEGER .1.3.6.1.4.1.251.1.1.1.15.1.14 |
sysLKEgEFCIThresholdTransmit EFCI thresholdrw INTEGER .1.3.6.1.4.1.251.1.1.1.15.1.15 |
sysLKIgEFCIThresholdReceive EFCI thresholdrw INTEGER .1.3.6.1.4.1.251.1.1.1.15.1.16 |
sysLKEgLogBufferTransmit logic buffer sizerw INTEGER .1.3.6.1.4.1.251.1.1.1.15.1.17 |
sysLKIgLogBufferReceive logic buffer sizerw INTEGER .1.3.6.1.4.1.251.1.1.1.15.1.18 |
sysLKEgFIFODepthTransmit FIFO Depthro INTEGER .1.3.6.1.4.1.251.1.1.1.15.1.19 |
sysLKIgFIFODepthReceive FIFO Depthro INTEGER .1.3.6.1.4.1.251.1.1.1.15.1.20 |
sysLKEgMemBlockIdTransmit Memory Block IDro Enumeration .1.3.6.1.4.1.251.1.1.1.15.1.21 |
sysLKIgMemBlockIdReceive Memory Block IDro Enumeration .1.3.6.1.4.1.251.1.1.1.15.1.22 |
sysDbTableThis table contains information about the internal buffer pool on the slot controller. SEQUENCE OF SysDbEntry .1.3.6.1.4.1.251.1.1.1.16 |
sysDbEntry SysDbEntry .1.3.6.1.4.1.251.1.1.1.16.1 |
sysDbIndexBuffer class numberro INTEGER .1.3.6.1.4.1.251.1.1.1.16.1.1 |
sysDbSizeFive classes of buffers are used:- 16, 128, 368 and 1600 bytes plus 48 bytes for cells.ro Enumeration .1.3.6.1.4.1.251.1.1.1.16.1.2 |
sysDbInitialThis is the initial number of buffers available.ro INTEGER .1.3.6.1.4.1.251.1.1.1.16.1.3 |
sysDbCurrentThis is the current number of buffers available.ro INTEGER .1.3.6.1.4.1.251.1.1.1.16.1.4 |
sysAuthenticateTableTable containing all the authentication tuples for this agent. SEQUENCE OF SysAuthenticateEntry .1.3.6.1.4.1.251.1.1.1.17 |
sysAuthenticateEntryAn authentication tuple. A PDU from the ipaddress specified that contains
the community, will have access to this MIB. SysAuthenticateEntry .1.3.6.1.4.1.251.1.1.1.17.1 |
sysAuIndexIndex, identifying each entry in the authentication table.rw INTEGER .1.3.6.1.4.1.251.1.1.1.17.1.1 |
sysAuIpaddressThe network address of the manager that has authentication access to this agent.rw IpAddress .1.3.6.1.4.1.251.1.1.1.17.1.2 |
sysAuCommunityThe SNMP community for which the ipaddress is authenticated.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.251.1.1.1.17.1.3 |
sysAuAccessAccess permission for this ipaddress/community tuple.
Write access is required for performing SNMP sets.rw Enumeration .1.3.6.1.4.1.251.1.1.1.17.1.4 |
sysAuSendTrapsSet to send-none(2) to prevent traps being sent to this host.rw Enumeration .1.3.6.1.4.1.251.1.1.1.17.1.5 |
sysAuValiditySet to invalid(2) to delete this row.rw Enumeration .1.3.6.1.4.1.251.1.1.1.17.1.6 |
sysLastTrapMessageThis is used to contain the last trap string sent.ro DisplayString .1.3.6.1.4.1.251.1.1.1.18 |
sysConfigChangedThis indicates that a new <config.cfg> file is available.
This should not be set by the user.rw Enumeration .1.3.6.1.4.1.251.1.1.1.19 |
sysConfigFileSet to read(2) to re-read the <config.cfg> file. Set to write(3) to write
the existing configuration to <config.cfg>.rw Enumeration .1.3.6.1.4.1.251.1.1.1.20 |
sysCompileTimeDate and time of link in the form dd Mon yyyy hh:mm:ss.
For example:-
15 Aug 1994 10:12:21ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.251.1.1.1.21 |
slotNumberSlot Numberro INTEGER .1.3.6.1.4.1.251.1.1.1.22 |
sysLastResetTimeM2Date and time board was last reset.ro DateAndTime (SNMPv2-TC) .1.3.6.1.4.1.251.1.1.1.23 |
sysCurrentTimeM2Current date and time in the form dd Mon yyyy hh:mm:ss.
For example:-
15 Aug 1994 10:12:21rw DateAndTime (SNMPv2-TC) .1.3.6.1.4.1.251.1.1.1.24 |
limTypeStatusDescribes whether the lim and the DOC card are compatible.ro Enumeration .1.3.6.1.4.1.251.1.1.1.25 |
dv2Slot0 OBJECT IDENTIFIER .1.3.6.1.4.1.251.1.1.2 |
slot0IntIpIP address of SLOT 0 for ATM interface.ro IpAddress .1.3.6.1.4.1.251.1.1.2.1 |
slot0XpInUseThe current Switch Fabric in Servicero Enumeration .1.3.6.1.4.1.251.1.1.2.2 |
slot0XpToUseThis indicates the switch fabric card you want the switch to use.rw Enumeration .1.3.6.1.4.1.251.1.1.2.3 |
slot0StandbyXpSet to yes(1) to enable standby switch fabric.rw Enumeration .1.3.6.1.4.1.251.1.1.2.4 |
slot0PsuTable SEQUENCE OF Slot0PsuEntry .1.3.6.1.4.1.251.1.1.2.5 |
slot0PsuEntry Slot0PsuEntry .1.3.6.1.4.1.251.1.1.2.5.1 |
slot0PsuIndexPower-supply number.ro INTEGER .1.3.6.1.4.1.251.1.1.2.5.1.1 |
slot0PsuFaultIf fault(2) then this indicates a fault condition in the power-supply.ro Enumeration .1.3.6.1.4.1.251.1.1.2.5.1.2 |
slot0PsuTestFaultIf set to yes(1) the control button on the PSU module has been set to test fault mode.ro Enumeration .1.3.6.1.4.1.251.1.1.2.5.1.3 |
slot0PsuVoltageThis is a the voltage generated by the power-supply in millivolts.ro INTEGER .1.3.6.1.4.1.251.1.1.2.5.1.4 |
slot0PsuTempThis is the temperature of the power-supply module in degrees celsius.ro INTEGER .1.3.6.1.4.1.251.1.1.2.5.1.5 |
slot0PsuFanASpeedThis is the rotation speed of FAN A in RPM.ro INTEGER .1.3.6.1.4.1.251.1.1.2.5.1.6 |
slot0PsuFanBSpeedThis is the rotation speed of FAN B in RPM.ro INTEGER .1.3.6.1.4.1.251.1.1.2.5.1.7 |
slot0PsuFanCSpeedThis is the rotation speed of FAN C in RPM.ro INTEGER .1.3.6.1.4.1.251.1.1.2.5.1.8 |
slot0PsuResetIf set to yes(2) then the power-supply module is returned to its initial state.rw Enumeration .1.3.6.1.4.1.251.1.1.2.5.1.9 |
slot0PsuTypeShows the type of PSU fitted into switch.ro Enumeration .1.3.6.1.4.1.251.1.1.2.5.1.10 |
slot0PsuFanFailSet to yes(2) if the fan fails.ro Enumeration .1.3.6.1.4.1.251.1.1.2.5.1.11 |
slot0PsuTooHotSet to yes(2) if the PSU is too hotro Enumeration .1.3.6.1.4.1.251.1.1.2.5.1.12 |
slot0PsuFrontTooHotSet to yes(2) if the Front is too hotro Enumeration .1.3.6.1.4.1.251.1.1.2.5.1.13 |
slot0PhyTableThis table summarises the hardware installed in the switch. SEQUENCE OF Slot0PhyEntry .1.3.6.1.4.1.251.1.1.2.6 |
slot0PhyEntry Slot0PhyEntry .1.3.6.1.4.1.251.1.1.2.6.1 |
slot0PhySlotNoThis is the slot number in the switch.ro INTEGER .1.3.6.1.4.1.251.1.1.2.6.1.1 |
slot0PhyNameThis is a mnemonic name for the slot.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.251.1.1.2.6.1.2 |
slot0PhyTypeThis enumerated type defines the type of card fitted in the slot.ro Enumeration .1.3.6.1.4.1.251.1.1.2.6.1.3 |
slot0PhyDlimThis is the type of DLIM fitted to the slot.rw Enumeration .1.3.6.1.4.1.251.1.1.2.6.1.4 |
slot0PhySwVerVersion of the software running on this slot controller.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.251.1.1.2.6.1.5 |
slot0PhyStateThe state of the slot, -(1) indicates no card fitted.ro Enumeration .1.3.6.1.4.1.251.1.1.2.6.1.6 |
slot0PhyResetSetting to yes(2) will reset the slot - use with carerw Enumeration .1.3.6.1.4.1.251.1.1.2.6.1.7 |
slot0PhyReqStateSetting to shutdown(2) will stop the slot running. The slot should only be set to main(3) or shadow(4) if the slot is operating in hardware redundant mode with an adjacent slot.rw Enumeration .1.3.6.1.4.1.251.1.1.2.6.1.8 |
slot0PhyStateChangeIndicates link has changed state.ro Enumeration .1.3.6.1.4.1.251.1.1.2.6.1.10 |
slot0PhyLinkedSlotThis is used in hardware redundancy mode. If set to 0 then there is no associated slot. Otherwise the value is the slot number that will be used if this slot fails.rw INTEGER .1.3.6.1.4.1.251.1.1.2.6.1.11 |
slot0PhyLink0StateThis contains link 0 status.ro Enumeration .1.3.6.1.4.1.251.1.1.2.6.1.12 |
slot0PhyLink1StateThis contains link 1 status.ro Enumeration .1.3.6.1.4.1.251.1.1.2.6.1.13 |
slot0PhyLink2StateThis contains link 2 status.ro Enumeration .1.3.6.1.4.1.251.1.1.2.6.1.14 |
slot0PhyLink3StateThis contains link 3 status.ro Enumeration .1.3.6.1.4.1.251.1.1.2.6.1.15 |
slot0PhySlotSerNoSerial number of the slot controller.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.251.1.1.2.6.1.16 |
slot0PhySlotHwVerNoHardware version number and revision of the slot controller.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.251.1.1.2.6.1.17 |
slot0PhyDocSerNoSerial number of the DOC.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.251.1.1.2.6.1.18 |
slot0PhyDocHwVerNoHardware version number and revision of the DOC.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.251.1.1.2.6.1.19 |
slot0PhyMacAddressMAC address of the slot.rw PhysAddress (SNMPv2-TC) .1.3.6.1.4.1.251.1.1.2.6.1.20 |
slot0PhyChangeTimeM2Last date and time link changed state.ro DateAndTime (SNMPv2-TC) .1.3.6.1.4.1.251.1.1.2.6.1.21 |
slot0PhyLstChngLnkNumHolds the link number of the last link status to change.ro Enumeration .1.3.6.1.4.1.251.1.1.2.6.1.22 |
slot0PhyLstChngPrevLnkStatHolds the previous link state of the last link number whose status changed.ro Enumeration .1.3.6.1.4.1.251.1.1.2.6.1.23 |
slot0MaxUpSlotsThe maximum number of slots that have been up.ro INTEGER .1.3.6.1.4.1.251.1.1.2.7 |
slot0CurrentUpSlotsThe number of slots currently up.ro INTEGER .1.3.6.1.4.1.251.1.1.2.8 |
slot0IsStandbySlot0Set to yes(2) if there is a redundant slot 0 available.ro Enumeration .1.3.6.1.4.1.251.1.1.2.9 |
slot0TftpToStandbySet to no(2) to stop files being transferred to the out of service slot0 automatically when they are changed.rw Enumeration .1.3.6.1.4.1.251.1.1.2.10 |
slot0MibBroadcastBroadcasts particular tables to all other slots.rw Enumeration .1.3.6.1.4.1.251.1.1.2.11 |
slot0AddressThe E.164 address of the switch.rw E164 .1.3.6.1.4.1.251.1.1.2.14 |
slot0InUseThe Slot 0 card Redundancy Status.ro Enumeration .1.3.6.1.4.1.251.1.1.2.15 |
slot0ToUseThis indicates the Slot 0 card you want the switch to use.rw Enumeration .1.3.6.1.4.1.251.1.1.2.16 |
slot0redmodeThe Slot 0 card Redundancy mode.ro Enumeration .1.3.6.1.4.1.251.1.1.2.17 |
slot0IntIPMaskIP Mask for Internal Subnet.
To reconfigure, Save new configuration and
perform then warm Start.rw IpAddress .1.3.6.1.4.1.251.1.1.2.18 |
slot0SwitchIdSwitch ID for this Apex noderw INTEGER .1.3.6.1.4.1.251.1.1.2.19 |
ntms0docSignifies that the S0DOC is capable of communicating with an NTMrw Enumeration .1.3.6.1.4.1.251.1.1.2.20 |
slot0LecsPrefixThe NSAP network prefix for LECS.rw E164 .1.3.6.1.4.1.251.1.1.2.21 |
slot0LecsESIThe NSAP ESI for LECS.rw E164 .1.3.6.1.4.1.251.1.1.2.22 |
dv2Trace OBJECT IDENTIFIER .1.3.6.1.4.1.251.1.1.3 |
traceIpToggle for IP trace flag.rw Enumeration .1.3.6.1.4.1.251.1.1.3.1 |
traceUdpToggle for UDP trace flag.rw Enumeration .1.3.6.1.4.1.251.1.1.3.2 |
traceTcpToggle for TCP trace flag.rw Enumeration .1.3.6.1.4.1.251.1.1.3.3 |
traceSnmpToggle for SNMP trace flag.rw Enumeration .1.3.6.1.4.1.251.1.1.3.4 |
traceCatToggle for CAT trace flag.rw Enumeration .1.3.6.1.4.1.251.1.1.3.5 |
dv2SlipLine OBJECT IDENTIFIER .1.3.6.1.4.1.251.1.1.4 |
slipIpIP address of SLIP line.rw IpAddress .1.3.6.1.4.1.251.1.1.4.1 |
slipMaskMask for SLIP line.rw IpAddress .1.3.6.1.4.1.251.1.1.4.2 |
slipRemoteIpIP address of remote end of SLIP line.rw IpAddress .1.3.6.1.4.1.251.1.1.4.3 |
slipSpeedBaud rate of SLIP serial line.rw Enumeration .1.3.6.1.4.1.251.1.1.4.4 |
dv2StaticRoute OBJECT IDENTIFIER .1.3.6.1.4.1.251.1.1.5 |
dv2Clocks OBJECT IDENTIFIER .1.3.6.1.4.1.251.1.1.6 |
clksTxTimingRefTransmit Timing Referencerw Enumeration .1.3.6.1.4.1.251.1.1.6.1 |
clksSysRefSlotNumSystem Timing Reference Slot Numberrw INTEGER .1.3.6.1.4.1.251.1.1.6.2 |
clksSysRefLinkNumSystem Timing Reference Link Numberrw Enumeration .1.3.6.1.4.1.251.1.1.6.3 |
clksSysRefErrorSystem Timing Errorro Enumeration .1.3.6.1.4.1.251.1.1.6.4 |
dv2VcDoc OBJECT IDENTIFIER .1.3.6.1.4.1.251.1.1.8 |
vcDocTable SEQUENCE OF VcDocEntry .1.3.6.1.4.1.251.1.1.8.1 |
vcDocEntry VcDocEntry .1.3.6.1.4.1.251.1.1.8.1.1 |
vcDocLinkNoThis is the target link number for the PVC.ro INTEGER .1.3.6.1.4.1.251.1.1.8.1.1.1 |
vcDocEnableSetting to yes(1) enables the VCDOC channel.rw Enumeration .1.3.6.1.4.1.251.1.1.8.1.1.2 |
vcDocVpiVPI of the VC being used for cell transfers.ro VirtualPathIdentifier .1.3.6.1.4.1.251.1.1.8.1.1.3 |
vcDocVciVCI of the VC being used for cell transfers.ro VirtualCircuitIdentifier .1.3.6.1.4.1.251.1.1.8.1.1.4 |
vcDocLinkSpeedThis sets the speed at which the link is to run.rw Enumeration .1.3.6.1.4.1.251.1.1.8.1.1.5 |
vcDocCLinesThis sets how control lines should be processed. If Ignore(2) is set then the port is always online.rw Enumeration .1.3.6.1.4.1.251.1.1.8.1.1.6 |
vcDocFifoSizeThis is the size of the software emulated FIFO.rw INTEGER .1.3.6.1.4.1.251.1.1.8.1.1.7 |
vcDocLowWaterThis is the point at which the transmit clock is switched to low frequency. This must be between 0 and FIFO Size/2rw INTEGER .1.3.6.1.4.1.251.1.1.8.1.1.8 |
vcDocHighWaterThis is the point at which the transmit clock is switched to high frequency. This must be between FIFO size and FIFO Size/2rw INTEGER .1.3.6.1.4.1.251.1.1.8.1.1.9 |
vcDocTestModeThis is the type of self-test to perform with the VC DOC.rw Enumeration .1.3.6.1.4.1.251.1.1.8.1.1.10 |
vcDocTestValThis is the test value to use when doing the pattern-send test.rw Hex .1.3.6.1.4.1.251.1.1.8.1.1.11 |
vcDocPriorityThis indicates that cells will be sent with the priority bit set.ro INTEGER .1.3.6.1.4.1.251.1.1.8.1.1.12 |
vcDocSubaThis is the target link number for the VC.ro INTEGER .1.3.6.1.4.1.251.1.1.8.1.1.13 |
vcDocSaddrThis is the target slot number for the VC.ro INTEGER .1.3.6.1.4.1.251.1.1.8.1.1.14 |
vcDocClockFixIf yes(2) then the clock will not be varied to maintain the size of the send FIFO.rw Enumeration .1.3.6.1.4.1.251.1.1.8.1.1.15 |
vcStatTableThis is a two row table that contains status information about the VCDOC. SEQUENCE OF VcStatEntry .1.3.6.1.4.1.251.1.1.8.2 |
vcStatEntry VcStatEntry .1.3.6.1.4.1.251.1.1.8.2.1 |
vcStatPortNoThis is the originating port number for the PVCro INTEGER .1.3.6.1.4.1.251.1.1.8.2.1.1 |
vcStatRxStateThis indicates whether control lines are high at the other end of the link.ro Enumeration .1.3.6.1.4.1.251.1.1.8.2.1.2 |
vcStatTxStateThis indicates whether the local control lines are high.ro Enumeration .1.3.6.1.4.1.251.1.1.8.2.1.3 |
vcStatFifoCountThis indicates the number of cells waiting in the FIFO.ro INTEGER .1.3.6.1.4.1.251.1.1.8.2.1.4 |
vcStatOFlowNumber of Overflows.ro INTEGER .1.3.6.1.4.1.251.1.1.8.2.1.5 |
vcStatUFlowNumber of Underflows.ro INTEGER .1.3.6.1.4.1.251.1.1.8.2.1.6 |
vcStatReSyncThis is the number of times a sequence number resync has been required.ro INTEGER .1.3.6.1.4.1.251.1.1.8.2.1.7 |
vcStatInventedNumber of invented cells.ro INTEGER .1.3.6.1.4.1.251.1.1.8.2.1.8 |
vcStatRxCellsReceived cells count.ro Counter .1.3.6.1.4.1.251.1.1.8.2.1.9 |
vcStatTxCellsTransmitted cells count.ro Counter .1.3.6.1.4.1.251.1.1.8.2.1.10 |
vcStatRxSeqNoReceive current sequence number.ro INTEGER .1.3.6.1.4.1.251.1.1.8.2.1.11 |
vcStatTxSeqNoTransmit current sequence number.ro INTEGER .1.3.6.1.4.1.251.1.1.8.2.1.12 |
vcStatLastErrorLast error type.ro INTEGER .1.3.6.1.4.1.251.1.1.8.2.1.13 |
vcStatLastCompareLast compare value.ro INTEGER .1.3.6.1.4.1.251.1.1.8.2.1.14 |
vcStatTestErrorsNumber of test errors detected.ro INTEGER .1.3.6.1.4.1.251.1.1.8.2.1.15 |
dv2FrRelay OBJECT IDENTIFIER .1.3.6.1.4.1.251.1.1.9 |
fRelayStatTableThis contains the overall status information for the frame relay links. SEQUENCE OF FRelayStatEntry .1.3.6.1.4.1.251.1.1.9.1 |
fRelayStatEntry FRelayStatEntry .1.3.6.1.4.1.251.1.1.9.1.1 |
fRelStatLinkNoLocal send sequence.ro INTEGER .1.3.6.1.4.1.251.1.1.9.1.1.1 |
fRelStatLocSeqLocal send sequence.ro INTEGER .1.3.6.1.4.1.251.1.1.9.1.1.2 |
fRelStatLocAckLocal ack sequence.ro INTEGER .1.3.6.1.4.1.251.1.1.9.1.1.3 |
fRelStatLocStateLocal state of link.ro Enumeration .1.3.6.1.4.1.251.1.1.9.1.1.4 |
fRelStatLocStartTLocal start time for poll.ro INTEGER .1.3.6.1.4.1.251.1.1.9.1.1.5 |
fRelStatLocErrThrLocal error threshold Counter.ro Counter .1.3.6.1.4.1.251.1.1.9.1.1.6 |
fRelStatLocMecLocal monitored events Counter.ro Counter .1.3.6.1.4.1.251.1.1.9.1.1.7 |
fRelStatLocPollLocal poll Counter for DTE.ro Counter .1.3.6.1.4.1.251.1.1.9.1.1.8 |
fRelStatRemSeqRemote send sequence.ro INTEGER .1.3.6.1.4.1.251.1.1.9.1.1.9 |
fRelStatRemAckRemote ack sequence.ro INTEGER .1.3.6.1.4.1.251.1.1.9.1.1.10 |
fRelStatRemStateRemote state of link.ro Enumeration .1.3.6.1.4.1.251.1.1.9.1.1.11 |
fRelStatRemStartTRemote start time for poll.ro INTEGER .1.3.6.1.4.1.251.1.1.9.1.1.12 |
fRelStatRemErrThrRemote error threshold Counter.ro Counter .1.3.6.1.4.1.251.1.1.9.1.1.13 |
fRelStatRemMecRemote monitored events Counter.ro Counter .1.3.6.1.4.1.251.1.1.9.1.1.14 |
fRelStatRemPollRemote poll Counter for DTE.ro Counter .1.3.6.1.4.1.251.1.1.9.1.1.15 |
fRelayConfTableThis table contains the overall configuration for the frame relay links. SEQUENCE OF FRelayConfEntry .1.3.6.1.4.1.251.1.1.9.2 |
fRelayConfEntry FRelayConfEntry .1.3.6.1.4.1.251.1.1.9.2.1 |
fRelConfLinkNoNumber of the link to configure.ro INTEGER .1.3.6.1.4.1.251.1.1.9.2.1.1 |
fRelConfLinkEnabSet to yes(1) to enable the link.rw Enumeration .1.3.6.1.4.1.251.1.1.9.2.1.2 |
fRelConfLinkModeframe mode.rw Enumeration .1.3.6.1.4.1.251.1.1.9.2.1.3 |
fRelConfLinkSpeedLocal speed of link.rw Enumeration .1.3.6.1.4.1.251.1.1.9.2.1.4 |
fRelConfLinkClineSet to no(2) to disable control line processing.rw Enumeration .1.3.6.1.4.1.251.1.1.9.2.1.5 |
fRelConfLinkTypeType of link.rw Enumeration .1.3.6.1.4.1.251.1.1.9.2.1.6 |
fRelConfN391Poll count.rw INTEGER .1.3.6.1.4.1.251.1.1.9.2.1.7 |
fRelConfN392Threshold.rw INTEGER .1.3.6.1.4.1.251.1.1.9.2.1.8 |
fRelConfN393Monitored events.rw INTEGER .1.3.6.1.4.1.251.1.1.9.2.1.9 |
fRelConfT391Poll period.rw INTEGER .1.3.6.1.4.1.251.1.1.9.2.1.10 |
fRelConfT392Poll timeout.rw INTEGER .1.3.6.1.4.1.251.1.1.9.2.1.11 |
fraPStatTableThis shows the status of the frame relay PVCs for link 0. SEQUENCE OF FraPStatEntry .1.3.6.1.4.1.251.1.1.9.3 |
fraPStatEntry FraPStatEntry .1.3.6.1.4.1.251.1.1.9.3.1 |
fraPStatDlciThis is the DLCI for the PVC.ro INTEGER .1.3.6.1.4.1.251.1.1.9.3.1.1 |
fraPStatRxBCntThe number of bytes received.ro Counter .1.3.6.1.4.1.251.1.1.9.3.1.2 |
fraPStatTxBCntThe number of bytes transmitted.ro Counter .1.3.6.1.4.1.251.1.1.9.3.1.3 |
fraPStatRxFCntThe number of frames received.ro Counter .1.3.6.1.4.1.251.1.1.9.3.1.4 |
fraPStatTxFCntThe number of frames transmitted.ro Counter .1.3.6.1.4.1.251.1.1.9.3.1.5 |
fraPStatRxBRateThe rate of bytes being received.ro Gauge .1.3.6.1.4.1.251.1.1.9.3.1.6 |
fraPStatTxBRateThe rate of bytes being transmitted.ro Gauge .1.3.6.1.4.1.251.1.1.9.3.1.7 |
fraPStatRxFRateThe rate of frames being received.ro Gauge .1.3.6.1.4.1.251.1.1.9.3.1.8 |
fraPStatTxFRateThe rate of frames being transmitted.ro Gauge .1.3.6.1.4.1.251.1.1.9.3.1.9 |
fraPStatDERxFThe count of discarded eligible received frames.ro Counter .1.3.6.1.4.1.251.1.1.9.3.1.10 |
fraPStatDisRxFThe count of discarded received frames.ro Counter .1.3.6.1.4.1.251.1.1.9.3.1.11 |
fraPStatPvcStatThe state of the PVC.ro Hex .1.3.6.1.4.1.251.1.1.9.3.1.12 |
fraPStatLinkStateThe state of the link.ro Hex .1.3.6.1.4.1.251.1.1.9.3.1.13 |
fraPStatLocSeqThe local send sequence.ro INTEGER .1.3.6.1.4.1.251.1.1.9.3.1.14 |
fraPStatLocAckThe local acknowledge number.ro INTEGER .1.3.6.1.4.1.251.1.1.9.3.1.15 |
fraPStatLocStatThe local state of the link.ro INTEGER .1.3.6.1.4.1.251.1.1.9.3.1.16 |
fraPStatLocStartTThe local start time for poll.ro INTEGER .1.3.6.1.4.1.251.1.1.9.3.1.17 |
fraPStatLocErrThrThe local error threshold Counter.ro Counter .1.3.6.1.4.1.251.1.1.9.3.1.18 |
fraPStatLocMecThe local monitored event Counter.ro Counter .1.3.6.1.4.1.251.1.1.9.3.1.19 |
fraPStatLocPollThe local poll Counter for DTE.ro Counter .1.3.6.1.4.1.251.1.1.9.3.1.20 |
fraPStatRemSeqThe remote send sequence.ro INTEGER .1.3.6.1.4.1.251.1.1.9.3.1.21 |
fraPStatRemAckThe remote acknowledge number.ro INTEGER .1.3.6.1.4.1.251.1.1.9.3.1.22 |
fraPStatRemStatThe remote state of the link.ro INTEGER .1.3.6.1.4.1.251.1.1.9.3.1.23 |
fraPStatRemStartTThe remote start time for poll.ro INTEGER .1.3.6.1.4.1.251.1.1.9.3.1.24 |
fraPStatRemErrThrThe remote error threshold Counter.ro Counter .1.3.6.1.4.1.251.1.1.9.3.1.25 |
fraPStatRemMecThe remote monitored event Counter.ro Counter .1.3.6.1.4.1.251.1.1.9.3.1.26 |
fraPStatRemPollThe remote poll Counter for DTE.ro Counter .1.3.6.1.4.1.251.1.1.9.3.1.27 |
fraPStatLastChangeM2The date and time of last state change.ro DateAndTime (SNMPv2-TC) .1.3.6.1.4.1.251.1.1.9.3.1.29 |
fraPConfigTable SEQUENCE OF FraPConfigEntry .1.3.6.1.4.1.251.1.1.9.4 |
fraPConfigEntry FraPConfigEntry .1.3.6.1.4.1.251.1.1.9.4.1 |
fraPConfigDlciThis is the DLCI for the PVC.rw INTEGER .1.3.6.1.4.1.251.1.1.9.4.1.1 |
fraPConfigCirThe committed information rate.rw INTEGER .1.3.6.1.4.1.251.1.1.9.4.1.2 |
fraPConfigCommitBThe committed burst rate.rw INTEGER .1.3.6.1.4.1.251.1.1.9.4.1.3 |
fraPConfigExcessBThe excess burst size.rw INTEGER .1.3.6.1.4.1.251.1.1.9.4.1.4 |
fraVpiThe VPI for this call.ro VirtualPathIdentifier .1.3.6.1.4.1.251.1.1.9.4.1.5 |
fraVciThe VCI for the call.ro VirtualCircuitIdentifier .1.3.6.1.4.1.251.1.1.9.4.1.6 |
fraPConfigPriorityro INTEGER .1.3.6.1.4.1.251.1.1.9.4.1.7 |
fraPConfigSubaro INTEGER .1.3.6.1.4.1.251.1.1.9.4.1.8 |
fraPConfigSaddrro INTEGER .1.3.6.1.4.1.251.1.1.9.4.1.9 |
fraPConfigValidityProvides a way of deleting a row in the table when
set to invalid.rw Enumeration .1.3.6.1.4.1.251.1.1.9.4.1.10 |
fraPConfigDxivpiThis is the VPI for the PVCrw INTEGER .1.3.6.1.4.1.251.1.1.9.4.1.11 |
fraPConfigDxivciThis is the VCI for the PVCrw INTEGER .1.3.6.1.4.1.251.1.1.9.4.1.12 |
fraPConfigDximodeThis flag indicates whether the mode is DXI - in that case the value of DLCI is ignoredrw Enumeration .1.3.6.1.4.1.251.1.1.9.4.1.13 |
frbPStatTableThis table shows statistics about the Frame Relay PVCs for link 1. SEQUENCE OF FrbPStatEntry .1.3.6.1.4.1.251.1.1.9.5 |
frbPStatEntry FrbPStatEntry .1.3.6.1.4.1.251.1.1.9.5.1 |
frbPStatDlciThis is the DLCI for the PVC.ro INTEGER .1.3.6.1.4.1.251.1.1.9.5.1.1 |
frbPStatRxBCntThe number of bytes received.ro Counter .1.3.6.1.4.1.251.1.1.9.5.1.2 |
frbPStatTxBCntThe number of bytes transmitted.ro Counter .1.3.6.1.4.1.251.1.1.9.5.1.3 |
frbPStatRxFCntThe number of frames received.ro Counter .1.3.6.1.4.1.251.1.1.9.5.1.4 |
frbPStatTxFCntThe number of frames transmitted.ro Counter .1.3.6.1.4.1.251.1.1.9.5.1.5 |
frbPStatRxBRateThe rate of bytes being received.ro Gauge .1.3.6.1.4.1.251.1.1.9.5.1.6 |
frbPStatTxBRateThe rate of bytes being transmitted.ro Gauge .1.3.6.1.4.1.251.1.1.9.5.1.7 |
frbPStatRxFRateThe rate of frames being received.ro Gauge .1.3.6.1.4.1.251.1.1.9.5.1.8 |
frbPStatTxFRateThe rate of frames being transmitted.ro Gauge .1.3.6.1.4.1.251.1.1.9.5.1.9 |
frbPStatDERxFThe count of discarded eligible received frames.ro Counter .1.3.6.1.4.1.251.1.1.9.5.1.10 |
frbPStatDisRxFThe count of discarded received frames.ro Counter .1.3.6.1.4.1.251.1.1.9.5.1.11 |
frbPStatPvcStatThe state of the PVC.ro Hex .1.3.6.1.4.1.251.1.1.9.5.1.12 |
frbPStatLinkStateThe state of the link.ro Hex .1.3.6.1.4.1.251.1.1.9.5.1.13 |
frbPStatLocSeqThe local send sequence.ro INTEGER .1.3.6.1.4.1.251.1.1.9.5.1.14 |
frbPStatLocAckThe local acknowledge number.ro INTEGER .1.3.6.1.4.1.251.1.1.9.5.1.15 |
frbPStatLocStatThe local state of the link.ro INTEGER .1.3.6.1.4.1.251.1.1.9.5.1.16 |
frbPStatLocStartTThe local start time for poll.ro INTEGER .1.3.6.1.4.1.251.1.1.9.5.1.17 |
frbPStatLocErrThrThe local error threshold Counter.ro Counter .1.3.6.1.4.1.251.1.1.9.5.1.18 |
frbPStatLocMecThe local monitored event Counter.ro Counter .1.3.6.1.4.1.251.1.1.9.5.1.19 |
frbPStatLocPollThe local poll Counter for DTE.ro Counter .1.3.6.1.4.1.251.1.1.9.5.1.20 |
frbPStatRemSeqThe remote send sequence.ro INTEGER .1.3.6.1.4.1.251.1.1.9.5.1.21 |
frbPStatRemAckThe remote acknowledge number.ro INTEGER .1.3.6.1.4.1.251.1.1.9.5.1.22 |
frbPStatRemStatThe remote state of the link.ro INTEGER .1.3.6.1.4.1.251.1.1.9.5.1.23 |
frbPStatRemStartTThe remote start time for poll.ro INTEGER .1.3.6.1.4.1.251.1.1.9.5.1.24 |
frbPStatRemErrThrThe remote error threshold Counter.ro Counter .1.3.6.1.4.1.251.1.1.9.5.1.25 |
frbPStatRemMecThe remote monitored event Counter.ro Counter .1.3.6.1.4.1.251.1.1.9.5.1.26 |
frbPStatRemPollThe remote poll Counter for DTE.ro Counter .1.3.6.1.4.1.251.1.1.9.5.1.27 |
frbPStatLastChangeM2The date and time of last state change.ro DateAndTime (SNMPv2-TC) .1.3.6.1.4.1.251.1.1.9.5.1.29 |
frbPConfigTable SEQUENCE OF FrbPConfigEntry .1.3.6.1.4.1.251.1.1.9.6 |
frbPConfigEntry FrbPConfigEntry .1.3.6.1.4.1.251.1.1.9.6.1 |
frbPConfigDlciThis is the DLCI for the PVC.rw INTEGER .1.3.6.1.4.1.251.1.1.9.6.1.1 |
frbPConfigCirThe committed information rate.rw INTEGER .1.3.6.1.4.1.251.1.1.9.6.1.2 |
frbPConfigCommitBThe committed burst rate.rw INTEGER .1.3.6.1.4.1.251.1.1.9.6.1.3 |
frbPConfigExcessBThe excess burst size.rw INTEGER .1.3.6.1.4.1.251.1.1.9.6.1.4 |
frbVpiThe VPI for this call.ro VirtualPathIdentifier .1.3.6.1.4.1.251.1.1.9.6.1.5 |
frbVciThe VCI for the call.ro VirtualCircuitIdentifier .1.3.6.1.4.1.251.1.1.9.6.1.6 |
frbPConfigPriorityro INTEGER .1.3.6.1.4.1.251.1.1.9.6.1.7 |
frbPConfigSubaro INTEGER .1.3.6.1.4.1.251.1.1.9.6.1.8 |
frbPConfigSaddrro INTEGER .1.3.6.1.4.1.251.1.1.9.6.1.9 |
frbPConfigValidityProvides a way of deleting a row in the table when
set to invalid.rw Enumeration .1.3.6.1.4.1.251.1.1.9.6.1.10 |
frbPConfigDxivpiThis is the VPI for the PVCrw INTEGER .1.3.6.1.4.1.251.1.1.9.6.1.11 |
frbPConfigDxivciThis is the VCI for the PVCrw INTEGER .1.3.6.1.4.1.251.1.1.9.6.1.12 |
frbPConfigDximodeThis flag indicates whether the mode is DXI - in that case the value of DLCI is ignoredrw Enumeration .1.3.6.1.4.1.251.1.1.9.6.1.13 |
dv2VcStatus OBJECT IDENTIFIER .1.3.6.1.4.1.251.1.1.10 |
vcaTableThis table shows detailed status for native ATM slot controller card link A VCs. SEQUENCE OF VcaEntry .1.3.6.1.4.1.251.1.1.10.3 |
vcaEntry VcaEntry .1.3.6.1.4.1.251.1.1.10.3.1 |
vcaVpiVirtual path identifier for the VC.ro INTEGER .1.3.6.1.4.1.251.1.1.10.3.1.1 |
vcaVciVirtual channel identifier for the VC.ro INTEGER .1.3.6.1.4.1.251.1.1.10.3.1.2 |
vcaTxGCellsNumber of transmitted good cells CLP0.ro Counter .1.3.6.1.4.1.251.1.1.10.3.1.3 |
vcaTxGCellsClp1Number of transmitted good cells CLP1.ro Counter .1.3.6.1.4.1.251.1.1.10.3.1.4 |
vcaRxGCellsNumber of received good cells.ro Counter .1.3.6.1.4.1.251.1.1.10.3.1.5 |
vcaExcessCellsNumber of cells discarded because of bucket overflow.ro Counter .1.3.6.1.4.1.251.1.1.10.3.1.6 |
vcaPeakExceedsNumber of cells discarded because of peak cell rate violation.ro Counter .1.3.6.1.4.1.251.1.1.10.3.1.7 |
vcaCellHeadThis value is bitwise OR'd with the cell header.ro Hex .1.3.6.1.4.1.251.1.1.10.3.1.8 |
vcaCellMaskThis value is bitwise AND'd with the cell header.ro Hex .1.3.6.1.4.1.251.1.1.10.3.1.9 |
vcaCellSwitchHeadThis comprises a tag which is added to the cell before putting into the cell switch and a control byte.ro Hex .1.3.6.1.4.1.251.1.1.10.3.1.10 |
vcaStartTimeThis is the bucket start time.ro INTEGER .1.3.6.1.4.1.251.1.1.10.3.1.11 |
vcaBucketControlThis is the bucket control register value.ro Hex .1.3.6.1.4.1.251.1.1.10.3.1.12 |
vcaBucket0CVThe current value of bucket 0.ro Gauge .1.3.6.1.4.1.251.1.1.10.3.1.13 |
vcaBucket0MaxThe maximum value of bucket 0.ro Gauge .1.3.6.1.4.1.251.1.1.10.3.1.14 |
vcaBucket0IncThe bucket 0 increment value.ro INTEGER .1.3.6.1.4.1.251.1.1.10.3.1.15 |
vcaBucket1CVThe current value of bucket 1.ro Gauge .1.3.6.1.4.1.251.1.1.10.3.1.16 |
vcaBucket1MaxThe maximum value of bucket 1.ro Gauge .1.3.6.1.4.1.251.1.1.10.3.1.17 |
vcaBucket1IncThe bucket 1 increment value.ro INTEGER .1.3.6.1.4.1.251.1.1.10.3.1.18 |
vcaBucket2CVThe current value of bucket 2.ro Gauge .1.3.6.1.4.1.251.1.1.10.3.1.19 |
vcaBucket2MaxThe maximum value of bucket 2.ro Gauge .1.3.6.1.4.1.251.1.1.10.3.1.20 |
vcaBucket2IncThe bucket 2 increment value.ro INTEGER .1.3.6.1.4.1.251.1.1.10.3.1.21 |
vcaBucket3CVThe current value of bucket 3.ro Gauge .1.3.6.1.4.1.251.1.1.10.3.1.22 |
vcaBucket3MaxThe maximum value of bucket 3.ro Gauge .1.3.6.1.4.1.251.1.1.10.3.1.23 |
vcaBucket3IncThe bucket 3 increment value.ro INTEGER .1.3.6.1.4.1.251.1.1.10.3.1.24 |
vcaTypeVirtual channel type for the VC.ro Enumeration .1.3.6.1.4.1.251.1.1.10.3.1.25 |
vcaDstSlotslot # this VC is going toro INTEGER .1.3.6.1.4.1.251.1.1.10.3.1.26 |
vcaDstLinklink # this VC is going toro INTEGER .1.3.6.1.4.1.251.1.1.10.3.1.27 |
vcaDstVpiVPI this VC is destined for.ro INTEGER .1.3.6.1.4.1.251.1.1.10.3.1.28 |
vcaDstVciVCI for this VC is destined for.ro INTEGER .1.3.6.1.4.1.251.1.1.10.3.1.29 |
vcaInternalVpiInternal VPIro INTEGER .1.3.6.1.4.1.251.1.1.10.3.1.30 |
vcaInternalVciInternal VCIro INTEGER .1.3.6.1.4.1.251.1.1.10.3.1.31 |
vcbTableThis table shows detailed status for native ATM slot controller card link B VCs. SEQUENCE OF VcbEntry .1.3.6.1.4.1.251.1.1.10.4 |
vcbEntry VcbEntry .1.3.6.1.4.1.251.1.1.10.4.1 |
vcbVpiVirtual path identifier for the VC.ro INTEGER .1.3.6.1.4.1.251.1.1.10.4.1.1 |
vcbVciVirtual channel identifier for the VC.ro INTEGER .1.3.6.1.4.1.251.1.1.10.4.1.2 |
vcbTxGCellsNumber of transmitted good cells CLP0.ro Counter .1.3.6.1.4.1.251.1.1.10.4.1.3 |
vcbTxGCellsClp1Number of transmitted good cells CLP1.ro Counter .1.3.6.1.4.1.251.1.1.10.4.1.4 |
vcbRxGCellsNumber of received good cells.ro Counter .1.3.6.1.4.1.251.1.1.10.4.1.5 |
vcbExcessCellsNumber of cells discarded because of bucket overflow.ro Counter .1.3.6.1.4.1.251.1.1.10.4.1.6 |
vcbPeakExceedsNumber of cells discarded because of peak cell rate violation.ro Counter .1.3.6.1.4.1.251.1.1.10.4.1.7 |
vcbCellHeadThis value is bitwise OR'd with the cell header.ro Hex .1.3.6.1.4.1.251.1.1.10.4.1.8 |
vcbCellMaskThis value is bitwise AND'd with the cell header.ro Hex .1.3.6.1.4.1.251.1.1.10.4.1.9 |
vcbCellSwitchHeadThis comprises a tag which is added to the cell before putting into the cell switch and a control byte.ro Hex .1.3.6.1.4.1.251.1.1.10.4.1.10 |
vcbStartTimeThis is the bucket start time.ro INTEGER .1.3.6.1.4.1.251.1.1.10.4.1.11 |
vcbBucketControlThis is the bucket control register value.ro Hex .1.3.6.1.4.1.251.1.1.10.4.1.12 |
vcbBucket0CVThe current value of bucket 0.ro Gauge .1.3.6.1.4.1.251.1.1.10.4.1.13 |
vcbBucket0MaxThe maximum value of bucket 0.ro Gauge .1.3.6.1.4.1.251.1.1.10.4.1.14 |
vcbBucket0IncThe bucket 0 increment value.ro INTEGER .1.3.6.1.4.1.251.1.1.10.4.1.15 |
vcbBucket1CVThe current value of bucket 1.ro Gauge .1.3.6.1.4.1.251.1.1.10.4.1.16 |
vcbBucket1MaxThe maximum value of bucket 1.ro Gauge .1.3.6.1.4.1.251.1.1.10.4.1.17 |
vcbBucket1IncThe bucket 1 increment value.ro INTEGER .1.3.6.1.4.1.251.1.1.10.4.1.18 |
vcbBucket2CVThe current value of bucket 2.ro Gauge .1.3.6.1.4.1.251.1.1.10.4.1.19 |
vcbBucket2MaxThe maximum value of bucket 2.ro Gauge .1.3.6.1.4.1.251.1.1.10.4.1.20 |
vcbBucket2IncThe bucket 2 increment value.ro INTEGER .1.3.6.1.4.1.251.1.1.10.4.1.21 |
vcbBucket3CVThe current value of bucket 3.ro Gauge .1.3.6.1.4.1.251.1.1.10.4.1.22 |
vcbBucket3MaxThe maximum value of bucket 3.ro Gauge .1.3.6.1.4.1.251.1.1.10.4.1.23 |
vcbBucket3IncThe bucket 3 increment value.ro INTEGER .1.3.6.1.4.1.251.1.1.10.4.1.24 |
vcbTypeVirtual channel type for the VC.ro Enumeration .1.3.6.1.4.1.251.1.1.10.4.1.25 |
vcbDstSlotslot # this VC is going toro INTEGER .1.3.6.1.4.1.251.1.1.10.4.1.26 |
vcbDstLinklink # this VC is going toro INTEGER .1.3.6.1.4.1.251.1.1.10.4.1.27 |
vcbDstVpiVPI this VC is destined for.ro INTEGER .1.3.6.1.4.1.251.1.1.10.4.1.28 |
vcbDstVciVCI for this VC is destined for.ro INTEGER .1.3.6.1.4.1.251.1.1.10.4.1.29 |
vcbInternalVpiInternal VPIro INTEGER .1.3.6.1.4.1.251.1.1.10.4.1.30 |
vcbInternalVciInternal VCIro INTEGER .1.3.6.1.4.1.251.1.1.10.4.1.31 |
xpStatTableThis table shows status of the switch fabric interface. SEQUENCE OF XpStatEntry .1.3.6.1.4.1.251.1.1.10.5 |
xpStatEntry XpStatEntry .1.3.6.1.4.1.251.1.1.10.5.1 |
xpIFaceSwitch fabric interface number.ro INTEGER .1.3.6.1.4.1.251.1.1.10.5.1.1 |
xpRXCellsSwitch fabric received cell count.ro Counter .1.3.6.1.4.1.251.1.1.10.5.1.2 |
xpTXCellsSwitch fabric transmit cell count.ro Counter .1.3.6.1.4.1.251.1.1.10.5.1.3 |
xpBadVpiVciNumber of cells with bad VCI/VPI received.ro Counter .1.3.6.1.4.1.251.1.1.10.5.1.4 |
xpRxOverflowNumber of receiver overflows.ro Counter .1.3.6.1.4.1.251.1.1.10.5.1.5 |
xpTxHighPrOverNumber of transmitted cells with high priority overflow.ro Counter .1.3.6.1.4.1.251.1.1.10.5.1.6 |
xpTxLowPrOverNumber of transmitted cells with low priority overflow.ro Counter .1.3.6.1.4.1.251.1.1.10.5.1.7 |
xpInputOverflowNumber of M68302 fabric input overflow cells.ro Counter .1.3.6.1.4.1.251.1.1.10.5.1.8 |
xpDocErrorsNumber of DOC errors.ro Counter .1.3.6.1.4.1.251.1.1.10.5.1.9 |
xpLowPriorityFifoRead transmit low priority FIFO count.ro Counter .1.3.6.1.4.1.251.1.1.10.5.1.10 |
xpEgDiscCellsRead transmit discard cell count.ro Counter .1.3.6.1.4.1.251.1.1.10.5.1.11 |
xpIgDiscCellsRead receive discard cell count.ro Counter .1.3.6.1.4.1.251.1.1.10.5.1.12 |
dv2PLPP OBJECT IDENTIFIER .1.3.6.1.4.1.251.1.1.11 |
plppCTableThis table is used to control PLPP configuration. SEQUENCE OF PlppCEntry .1.3.6.1.4.1.251.1.1.11.1 |
plppCEntry PlppCEntry .1.3.6.1.4.1.251.1.1.11.1.1 |
plppCLinkNoThe link number for this configuration.ro INTEGER .1.3.6.1.4.1.251.1.1.11.1.1.1 |
plppCLinkEnabSet to yes(1) to enable the link.rw Enumeration .1.3.6.1.4.1.251.1.1.11.1.1.2 |
plppCCPLCPModeThe PLCP mode for link.rw Enumeration .1.3.6.1.4.1.251.1.1.11.1.1.3 |
plppCDS3FramerSet to yes(1) to enable the DS3 framer mode for this link.rw Enumeration .1.3.6.1.4.1.251.1.1.11.1.1.4 |
plppCScramblerSet to no(2) to disable the scrambler mode for this link.rw Enumeration .1.3.6.1.4.1.251.1.1.11.1.1.5 |
plppC0x55If set to no(2) then HCS is not XORed with 0x55rw Enumeration .1.3.6.1.4.1.251.1.1.11.1.1.6 |
plppCCLineControl line processing for this link.rw Enumeration .1.3.6.1.4.1.251.1.1.11.1.1.7 |
plppCLoopbackSet to yes(1) to enable loopback mode for this link.rw Enumeration .1.3.6.1.4.1.251.1.1.11.1.1.8 |
plppCSmdsModeSet to yes(1) to enable SMDS mode.rw Enumeration .1.3.6.1.4.1.251.1.1.11.1.1.12 |
plppCPloadTypeLabPay type label.rw INTEGER .1.3.6.1.4.1.251.1.1.11.1.1.13 |
plppCTxTrlTrcIdLenTrail trace length for transmit and expected receive.rw Enumeration .1.3.6.1.4.1.251.1.1.11.1.1.14 |
plppCTxTrcIdTransmit trail trace identifier.rw PhysAddress .1.3.6.1.4.1.251.1.1.11.1.1.15 |
plppCRxExTrcIdReceive expected trail trace identifier.rw PhysAddress .1.3.6.1.4.1.251.1.1.11.1.1.16 |
plppSTableThe status table for plpp. SEQUENCE OF PlppSEntry .1.3.6.1.4.1.251.1.1.11.2 |
plppSEntry PlppSEntry .1.3.6.1.4.1.251.1.1.11.2.1 |
plppSLinkNoThe link number for this status.ro INTEGER .1.3.6.1.4.1.251.1.1.11.2.1.1 |
plppSCLinesThe state of control lines for this link.ro Enumeration .1.3.6.1.4.1.251.1.1.11.2.1.2 |
plppSTXclockThe state of TX clock for this link.ro Enumeration .1.3.6.1.4.1.251.1.1.11.2.1.3 |
plppSRXclockThe state of RX clock for this link.ro Enumeration .1.3.6.1.4.1.251.1.1.11.2.1.4 |
plppSTXCellsThe transmit cells count for this link.ro Counter .1.3.6.1.4.1.251.1.1.11.2.1.5 |
plppSRXCellsThe receive cells count for this link.ro Counter .1.3.6.1.4.1.251.1.1.11.2.1.6 |
plppSHCSErrsThe header checksum error count for this link.ro Counter .1.3.6.1.4.1.251.1.1.11.2.1.7 |
plppSFrameErrsThe frame error count for this link.ro Counter .1.3.6.1.4.1.251.1.1.11.2.1.11 |
plppSBIP8ErrsThe BIP-8 error count for this link.ro Counter .1.3.6.1.4.1.251.1.1.11.2.1.12 |
plppSFEBEErrsThe FEBE error count for this link.ro Counter .1.3.6.1.4.1.251.1.1.11.2.1.13 |
plppSSPLRStatusThe SPLR Status Register Contents.ro INTEGER .1.3.6.1.4.1.251.1.1.11.2.1.14 |
plppSDs3LcvsThe DS3 LCV count for this link.ro Counter .1.3.6.1.4.1.251.1.1.11.2.1.15 |
plppSDs3FrameErrsThe DS3 frame error count for this link.ro Counter .1.3.6.1.4.1.251.1.1.11.2.1.16 |
plppSDs3ParityErrsThe DS3 parity error count for this link.ro Counter .1.3.6.1.4.1.251.1.1.11.2.1.17 |
plppSDs3CbitPrtyErrsThe DS3 control bit parity error count for this link.ro Counter .1.3.6.1.4.1.251.1.1.11.2.1.18 |
plppSDs3FEBEErrsThe DS3 FEBE error count for this link.ro Counter .1.3.6.1.4.1.251.1.1.11.2.1.19 |
plppSDs3RxAISReceive DS3 AIS status.ro Enumeration .1.3.6.1.4.1.251.1.1.11.2.1.20 |
plppSDs3RxRedAlarmReceive DS3 Red Alarm status.ro Enumeration .1.3.6.1.4.1.251.1.1.11.2.1.21 |
plppSDs3RxYellowAlarmReceive DS3 Yellow Alarm status.ro Enumeration .1.3.6.1.4.1.251.1.1.11.2.1.22 |
plppSPLCPRxYellowAlarmReceive PLCP Yellow Alarm status.ro Enumeration .1.3.6.1.4.1.251.1.1.11.2.1.23 |
plppsRxTrIdMisReceive trace id mismatch indication.ro Enumeration .1.3.6.1.4.1.251.1.1.11.2.1.24 |
plppsRxTrIdUnstReceive trace id unstable indication.ro Enumeration .1.3.6.1.4.1.251.1.1.11.2.1.25 |
plppsRxPloadTypeLabMisReceive payload type label mismatch indication.ro Enumeration .1.3.6.1.4.1.251.1.1.11.2.1.26 |
plppsRxPloadTypeLabUnstReceive payload type label unstable indication.ro Enumeration .1.3.6.1.4.1.251.1.1.11.2.1.27 |
plppsRxTrlTrcLast received trail trace message.ro PhysAddress .1.3.6.1.4.1.251.1.1.11.2.1.28 |
plppV2CTableThis table is used to control DS3-2C PLPP configuration. SEQUENCE OF PlppV2CEntry .1.3.6.1.4.1.251.1.1.11.3 |
plppV2CEntry PlppV2CEntry .1.3.6.1.4.1.251.1.1.11.3.1 |
plppV2CLinkNoThe link number for this configuration.ro INTEGER .1.3.6.1.4.1.251.1.1.11.3.1.1 |
plppV2CLinkEnabSet to yes(1) to enable the link.rw Enumeration .1.3.6.1.4.1.251.1.1.11.3.1.2 |
plppV2CCPLCPModeSet to yes(1) to enable the PLCP layer mode for this link.rw Enumeration .1.3.6.1.4.1.251.1.1.11.3.1.3 |
plppV2CDS3FramerSet to yes(1) to enable the DS3 framer mode for this link.rw Enumeration .1.3.6.1.4.1.251.1.1.11.3.1.4 |
plppV2CScramblerSet to no(2) to disable the scrambler mode for this link.rw Enumeration .1.3.6.1.4.1.251.1.1.11.3.1.5 |
plppV2C0x55If set to no(2) then HCS is not XORed with 0x55rw Enumeration .1.3.6.1.4.1.251.1.1.11.3.1.6 |
plppV2CLoopbackSet to yes(1) to enable loopback mode for this link.rw Enumeration .1.3.6.1.4.1.251.1.1.11.3.1.7 |
plppV2CSmdsModeSet to yes(1) to enable SMDS mode.rw Enumeration .1.3.6.1.4.1.251.1.1.11.3.1.8 |
plppV2CFrmFmtSet to yes(1) to enable C-bit parity framing format.rw Enumeration .1.3.6.1.4.1.251.1.1.11.3.1.9 |
plppV2CTxAISSet to yes(1) to enable framer to Txmt AIS.rw Enumeration .1.3.6.1.4.1.251.1.1.11.3.1.10 |
plppV2STableThe status table for DS3-2C plpp. SEQUENCE OF PlppV2SEntry .1.3.6.1.4.1.251.1.1.11.4 |
plppV2SEntry PlppV2SEntry .1.3.6.1.4.1.251.1.1.11.4.1 |
plppV2SLinkNoThe link number for this status.ro INTEGER .1.3.6.1.4.1.251.1.1.11.4.1.1 |
plppV2STXclockThe state of TX clock for this link.ro Enumeration .1.3.6.1.4.1.251.1.1.11.4.1.2 |
plppV2SRXclockThe state of RX clock for this link.ro Enumeration .1.3.6.1.4.1.251.1.1.11.4.1.3 |
plppV2STXCellsThe transmit cells count for this link.ro Counter .1.3.6.1.4.1.251.1.1.11.4.1.4 |
plppV2SRXCellsThe receive cells count for this link.ro Counter .1.3.6.1.4.1.251.1.1.11.4.1.5 |
plppV2SHCSErrsThe header checksum error count for this link.ro Counter .1.3.6.1.4.1.251.1.1.11.4.1.6 |
plppV2SFrameErrsThe frame error count for this link.ro Counter .1.3.6.1.4.1.251.1.1.11.4.1.7 |
plppV2SBIP8ErrsThe BIP-8 error count for this link.ro Counter .1.3.6.1.4.1.251.1.1.11.4.1.8 |
plppV2SFEBEErrsThe FEBE error count for this link.ro Counter .1.3.6.1.4.1.251.1.1.11.4.1.9 |
plppV2SSPLRStatusyes(1) indicates a PLCP LOF.ro Enumeration .1.3.6.1.4.1.251.1.1.11.4.1.10 |
plppV2SDs3FrmFmtOperate in DS3 C-bit Parity or drop-back to Clear Channel.ro Enumeration .1.3.6.1.4.1.251.1.1.11.4.1.11 |
plppV2SDs3LcvsThe DS3 LCV count for this link.ro Counter .1.3.6.1.4.1.251.1.1.11.4.1.12 |
plppV2SDs3FrameErrsThe DS3 frame error count for this link.ro Counter .1.3.6.1.4.1.251.1.1.11.4.1.13 |
plppV2SDs3ParityErrsThe DS3 parity error count for this link.ro Counter .1.3.6.1.4.1.251.1.1.11.4.1.14 |
plppV2SDs3CbitPrtyErrsThe DS3 control bit parity error count for this link.ro Counter .1.3.6.1.4.1.251.1.1.11.4.1.15 |
plppV2SDs3FEBEErrsThe DS3 FEBE error count for this link.ro Counter .1.3.6.1.4.1.251.1.1.11.4.1.16 |
plppV2SDs3RxAISReceive DS3 AIS status.ro Enumeration .1.3.6.1.4.1.251.1.1.11.4.1.17 |
plppV2SDs3RxRedAlarmReceive DS3 Red Alarm status.ro Enumeration .1.3.6.1.4.1.251.1.1.11.4.1.18 |
plppV2SDs3RxYellowAlarmReceive DS3 Yellow Alarm status.ro Enumeration .1.3.6.1.4.1.251.1.1.11.4.1.19 |
plppV2SPLCPRxYellowAlarmReceive PLCP Yellow Alarm status.ro Enumeration .1.3.6.1.4.1.251.1.1.11.4.1.20 |
plppV2SDs3FEACTxmtCode that has been transmitted as a FEAC.ro Enumeration .1.3.6.1.4.1.251.1.1.11.4.1.21 |
plppV2SRxIDLyes(1) indicates an IDLE has been received.ro Enumeration .1.3.6.1.4.1.251.1.1.11.4.1.22 |
plppV2SLOCReceive Loss of cell delineation.ro Enumeration .1.3.6.1.4.1.251.1.1.11.4.1.23 |
plppV2SDs3LPBKif yes(1), the DS3 Framer is in loopback.ro Enumeration .1.3.6.1.4.1.251.1.1.11.4.1.24 |
plppE1CTableThis table to control the E1-2C PLPP configuration. SEQUENCE OF PlppE1CEntry .1.3.6.1.4.1.251.1.1.11.5 |
plppE1CEntry PlppE1CEntry .1.3.6.1.4.1.251.1.1.11.5.1 |
plppE1CLinkNoThe link number for this configuration.ro INTEGER .1.3.6.1.4.1.251.1.1.11.5.1.1 |
plppE1CLinkEnabSet to yes(1) to enable the link.rw Enumeration .1.3.6.1.4.1.251.1.1.11.5.1.2 |
plppE1CScramblerSet to no(2) to disable the scrambler mode for this link.rw Enumeration .1.3.6.1.4.1.251.1.1.11.5.1.3 |
plppE1C0x55If set to no(2) then HCS is not XORed with 0x55rw Enumeration .1.3.6.1.4.1.251.1.1.11.5.1.4 |
plppE1CSmdsModeSet to yes(1) to enable SMDS mode.rw Enumeration .1.3.6.1.4.1.251.1.1.11.5.1.5 |
plppE1CLpbkSet to yes(1) to enable DOC Framer loopback.rw Enumeration .1.3.6.1.4.1.251.1.1.11.5.1.6 |
plppE1STableThe status table for E1-2C plpp. SEQUENCE OF PlppE1SEntry .1.3.6.1.4.1.251.1.1.11.6 |
plppE1SEntry PlppE1SEntry .1.3.6.1.4.1.251.1.1.11.6.1 |
plppE1SLinkNoThe link number for this status.ro INTEGER .1.3.6.1.4.1.251.1.1.11.6.1.1 |
plppE1STXclockThe state of TX clock for this link.ro Enumeration .1.3.6.1.4.1.251.1.1.11.6.1.2 |
plppE1SRXclockThe state of RX clock for this link.ro Enumeration .1.3.6.1.4.1.251.1.1.11.6.1.3 |
plppE1STXCellsThe transmit cells count for this link.ro Counter .1.3.6.1.4.1.251.1.1.11.6.1.4 |
plppE1SRXCellsThe receive cells count for this link.ro Counter .1.3.6.1.4.1.251.1.1.11.6.1.5 |
plppE1SHCSErrsThe HCS error count for this link.ro Counter .1.3.6.1.4.1.251.1.1.11.6.1.6 |
plppE1SCRCErrsThe CRC-4 error count for this link.ro Counter .1.3.6.1.4.1.251.1.1.11.6.1.7 |
plppE1SFrameErrsThe frame error count for this link.ro Counter .1.3.6.1.4.1.251.1.1.11.6.1.8 |
plppE1SFEBEErrsThe FEBE error count for this link.ro Counter .1.3.6.1.4.1.251.1.1.11.6.1.9 |
plppE1SLcvsThe E1 LCV count for this link.ro Counter .1.3.6.1.4.1.251.1.1.11.6.1.10 |
plppE1SRxAISReceive E1 AIS status.ro Enumeration .1.3.6.1.4.1.251.1.1.11.6.1.11 |
plppE1SRxOOFReceive E1 OOF status.ro Enumeration .1.3.6.1.4.1.251.1.1.11.6.1.12 |
plppE1SRxLOSReceive E1 LOS status.ro Enumeration .1.3.6.1.4.1.251.1.1.11.6.1.13 |
plppE1SRxLOFReceive E1 LOF status.ro Enumeration .1.3.6.1.4.1.251.1.1.11.6.1.14 |
plppE1SFerfReceiving a Far-End Receive Failure if yes.ro Enumeration .1.3.6.1.4.1.251.1.1.11.6.1.15 |
plppE3CTableThis table is used to control the E3-2C PLPP configuration. SEQUENCE OF PlppE3CEntry .1.3.6.1.4.1.251.1.1.11.7 |
plppE3CEntry PlppE3CEntry .1.3.6.1.4.1.251.1.1.11.7.1 |
plppE3CLinkNoThe link number for this configuration.ro INTEGER .1.3.6.1.4.1.251.1.1.11.7.1.1 |
plppE3CLinkEnabSet to yes(1) to enable the link.rw Enumeration .1.3.6.1.4.1.251.1.1.11.7.1.2 |
plppE3CFramerThe E3 framer mode for the link.rw Enumeration .1.3.6.1.4.1.251.1.1.11.7.1.3 |
plppE3CPLCPModeThe PLCP mode for the link.rw Enumeration .1.3.6.1.4.1.251.1.1.11.7.1.4 |
plppE3CScramblerSet to no(2) to disable the scrambler mode for this link.rw Enumeration .1.3.6.1.4.1.251.1.1.11.7.1.5 |
plppE3C0x55If set to no(2) then HCS is not XORed with 0x55rw Enumeration .1.3.6.1.4.1.251.1.1.11.7.1.6 |
plppE3CLoopbackSet to yes(1) to enable loopback mode for this link.rw Enumeration .1.3.6.1.4.1.251.1.1.11.7.1.7 |
plppE3CSmdsModeSet to yes(1) to enable SMDS mode.rw Enumeration .1.3.6.1.4.1.251.1.1.11.7.1.8 |
plppE3CTxmtTimMkSet to yes(1) if traceable to primary ref clk.rw Enumeration .1.3.6.1.4.1.251.1.1.11.7.1.9 |
plppE3CPloadTypeLabPayload type label.rw Enumeration .1.3.6.1.4.1.251.1.1.11.7.1.10 |
plppE3CTxTrlTrcIdLenTrail trace length for transmit and expected receive.rw Enumeration .1.3.6.1.4.1.251.1.1.11.7.1.11 |
plppE3CTxTrcIdUHTransmit trail trace ID upper half.rw PhysAddress .1.3.6.1.4.1.251.1.1.11.7.1.12 |
plppE3CTxTrcIdLHTransmit trail trace ID lower half.rw PhysAddress .1.3.6.1.4.1.251.1.1.11.7.1.13 |
plppE3CRxExTrcIdUHReceive expected trail trace ID upper half.rw PhysAddress .1.3.6.1.4.1.251.1.1.11.7.1.14 |
plppE3CRxExTrcIdLHReceive expected trail trace ID lower half.rw PhysAddress .1.3.6.1.4.1.251.1.1.11.7.1.15 |
plppE3STableThe E3-2C status table for plpp. SEQUENCE OF PlppE3SEntry .1.3.6.1.4.1.251.1.1.11.8 |
plppE3SEntry PlppE3SEntry .1.3.6.1.4.1.251.1.1.11.8.1 |
plppE3SLinkNoThe link number for this status.ro INTEGER .1.3.6.1.4.1.251.1.1.11.8.1.1 |
plppE3STXclockThe state of TX clock for this link.ro Enumeration .1.3.6.1.4.1.251.1.1.11.8.1.2 |
plppE3SRXclockThe state of RX clock for this link.ro Enumeration .1.3.6.1.4.1.251.1.1.11.8.1.3 |
plppE3STXCellsThe transmit cells count for this link.ro Counter .1.3.6.1.4.1.251.1.1.11.8.1.4 |
plppE3SRXCellsThe receive cells count for this link.ro Counter .1.3.6.1.4.1.251.1.1.11.8.1.5 |
plppE3SHCSErrsThe header checksum error count for this link.ro Counter .1.3.6.1.4.1.251.1.1.11.8.1.6 |
plppE3SE3FrameErrsThe E3 frame error count for this link.ro Counter .1.3.6.1.4.1.251.1.1.11.8.1.7 |
plppE3SPLCPFrameErrsThe PLCP frame error count for this link.ro Counter .1.3.6.1.4.1.251.1.1.11.8.1.8 |
plppE3SBIP8ErrsThe BIP-8 error count for this link.ro Counter .1.3.6.1.4.1.251.1.1.11.8.1.9 |
plppE3SFEBEErrsThe FEBE error count for this link.ro Counter .1.3.6.1.4.1.251.1.1.11.8.1.10 |
plppE3SLcvsThe E3 LCV count for this link.ro Counter .1.3.6.1.4.1.251.1.1.11.8.1.11 |
plppE3SLcdReceive Loss of cell delineation.ro Enumeration .1.3.6.1.4.1.251.1.1.11.8.1.12 |
plppE3SRxTrlTrcLast received trail trace message.ro PhysAddress .1.3.6.1.4.1.251.1.1.11.8.1.13 |
plppE3SRxAISReceive E3 AIS status.ro Enumeration .1.3.6.1.4.1.251.1.1.11.8.1.14 |
plppE3SRxOOFReceive E3 OOF status.ro Enumeration .1.3.6.1.4.1.251.1.1.11.8.1.15 |
plppE3SRxLOSReceive E3 LOS status.ro Enumeration .1.3.6.1.4.1.251.1.1.11.8.1.16 |
plppE3SRxLOFReceive E3 LOF status.ro Enumeration .1.3.6.1.4.1.251.1.1.11.8.1.17 |
plppE3SRxFERFReceive E3 FERF status.ro Enumeration .1.3.6.1.4.1.251.1.1.11.8.1.18 |
plppE3SPLCPRxLofThe PLCP Rx LOF for this link.ro Enumeration .1.3.6.1.4.1.251.1.1.11.8.1.19 |
plppE3SPLCPRxYellowAlarmReceive PLCP Yellow Alarm status.ro Enumeration .1.3.6.1.4.1.251.1.1.11.8.1.20 |
plppE3SRxTrIdMisReceive trace id mismatch indication.ro Enumeration .1.3.6.1.4.1.251.1.1.11.8.1.21 |
plppE3SRxTrIdUnstReceive trace id unstable indication.ro Enumeration .1.3.6.1.4.1.251.1.1.11.8.1.22 |
plppE3SRxPloadTypeLabMisReceive payload type label mismatch indication.ro Enumeration .1.3.6.1.4.1.251.1.1.11.8.1.23 |
plppE3SRxPloadTypeLabUnstReceive payload type label unstable indication.ro Enumeration .1.3.6.1.4.1.251.1.1.11.8.1.24 |
dv2LocalFibre OBJECT IDENTIFIER .1.3.6.1.4.1.251.1.1.12 |
lFibreConfTableThis table contains configuration information for the LFDOC. SEQUENCE OF LFibreConfEntry .1.3.6.1.4.1.251.1.1.12.1 |
lFibreConfEntry LFibreConfEntry .1.3.6.1.4.1.251.1.1.12.1.1 |
lFibreConfLinkNoThe link number for this configuration.ro INTEGER .1.3.6.1.4.1.251.1.1.12.1.1.1 |
lFibreConfLinkEnabSet to yes(1) to enable the link.rw Enumeration .1.3.6.1.4.1.251.1.1.12.1.1.2 |
lFibreConfCLineSet to ignored(2) to stop control line processing for this link.rw Enumeration .1.3.6.1.4.1.251.1.1.12.1.1.3 |
lFibreConfLoopbackSet to yes(1) to enable loopback mode for this link.rw Enumeration .1.3.6.1.4.1.251.1.1.12.1.1.4 |
lFibreStatTableThis table contains status information for the LFDOC SEQUENCE OF LFibreStatEntry .1.3.6.1.4.1.251.1.1.12.2 |
lFibreStatEntry LFibreStatEntry .1.3.6.1.4.1.251.1.1.12.2.1 |
lFibreStatLinkNoThe link number for this status.ro INTEGER .1.3.6.1.4.1.251.1.1.12.2.1.1 |
lFibreStatCLinesThe state of control lines for this link.ro Enumeration .1.3.6.1.4.1.251.1.1.12.2.1.2 |
lFibreStatHCSErrsThe header checksum error count for this link.ro Counter .1.3.6.1.4.1.251.1.1.12.2.1.3 |
dv2DS OBJECT IDENTIFIER .1.3.6.1.4.1.251.1.1.13 |
ds1Tableds1 Status Table SEQUENCE OF Ds1Entry .1.3.6.1.4.1.251.1.1.13.1 |
ds1Entry Ds1Entry .1.3.6.1.4.1.251.1.1.13.1.1 |
ds1LinkNoLink number - this is the instance.ro INTEGER .1.3.6.1.4.1.251.1.1.13.1.1.1 |
ds1LineLengthLength of the line connected to the physical interface.rw Enumeration .1.3.6.1.4.1.251.1.1.13.1.1.2 |
ds1FramingT1 Framing type.rw Enumeration .1.3.6.1.4.1.251.1.1.13.1.1.3 |
ds1CodingThe line code of incoming DS1 signal. ami(2) selects AMI line code.rw Enumeration .1.3.6.1.4.1.251.1.1.13.1.1.4 |
ds1TrSet to yes(1) to enable transmit loop-back.rw Enumeration .1.3.6.1.4.1.251.1.1.13.1.1.5 |
ds1RtSet to yes(1) to enable receive loop-back.rw Enumeration .1.3.6.1.4.1.251.1.1.13.1.1.6 |
ds1LOSDefectLoss of Signal Defectro Enumeration .1.3.6.1.4.1.251.1.1.13.1.1.7 |
ds1AISDefectAIS Defectro Enumeration .1.3.6.1.4.1.251.1.1.13.1.1.8 |
ds1OOFDefectOOF Defectro Enumeration .1.3.6.1.4.1.251.1.1.13.1.1.9 |
ds1YellowDefectYellow Defectro Enumeration .1.3.6.1.4.1.251.1.1.13.1.1.10 |
ds1LOSAlarmLoss Of Signal alarmro Enumeration .1.3.6.1.4.1.251.1.1.13.1.1.11 |
ds1AISAlarmAIS alarmro Enumeration .1.3.6.1.4.1.251.1.1.13.1.1.12 |
ds1LOFAlarmLoss Of Frame alarmro Enumeration .1.3.6.1.4.1.251.1.1.13.1.1.13 |
ds1YellowAlarmYellow alarmro Enumeration .1.3.6.1.4.1.251.1.1.13.1.1.14 |
ds1PdvCountNumber of pulse density violations detected.ro Counter .1.3.6.1.4.1.251.1.1.13.1.1.15 |
ds1Z16CountNumber of 16 consecutive zeroes detected.ro Counter .1.3.6.1.4.1.251.1.1.13.1.1.16 |
ds1LcvCountNumber of line code violations detected.ro Counter .1.3.6.1.4.1.251.1.1.13.1.1.17 |
ds1BeeCountNumber of block error events detected.ro Counter .1.3.6.1.4.1.251.1.1.13.1.1.18 |
ds1FerCountNumber of framing bit error events detected.ro Counter .1.3.6.1.4.1.251.1.1.13.1.1.19 |
ds1OofCountNumber of out of frame events detected.ro Counter .1.3.6.1.4.1.251.1.1.13.1.1.20 |
ds1ClrStatsClear countersrw Enumeration .1.3.6.1.4.1.251.1.1.13.1.1.21 |
ds1ReconfigReconfigure Linkrw Enumeration .1.3.6.1.4.1.251.1.1.13.1.1.22 |
ds1LineESLine Errored Secondsro Counter .1.3.6.1.4.1.251.1.1.13.1.1.23 |
ds1LineSESLine Severely Errored Secondsro Counter .1.3.6.1.4.1.251.1.1.13.1.1.24 |
ds1ESErrored Secondsro Counter .1.3.6.1.4.1.251.1.1.13.1.1.25 |
ds1SESSeverely Errored Secondsro Counter .1.3.6.1.4.1.251.1.1.13.1.1.26 |
ds1AISSAIS Secondsro Counter .1.3.6.1.4.1.251.1.1.13.1.1.27 |
ds1UASUnavailable Secondsro Counter .1.3.6.1.4.1.251.1.1.13.1.1.28 |
ds1TxClkSelTransmit clock select.rw Enumeration .1.3.6.1.4.1.251.1.1.13.1.1.29 |
ds1ExBERDefectExcessive Bit Error Rate Defectro Enumeration .1.3.6.1.4.1.251.1.1.13.1.1.30 |
ds1ExBERAlarmExcessive Bit Error Rate Alarmro Enumeration .1.3.6.1.4.1.251.1.1.13.1.1.31 |
ds3Tableds3 Status Table SEQUENCE OF Ds3Entry .1.3.6.1.4.1.251.1.1.13.2 |
ds3Entry Ds3Entry .1.3.6.1.4.1.251.1.1.13.2.1 |
ds3LinkNoLink number - this is the instance.ro INTEGER .1.3.6.1.4.1.251.1.1.13.2.1.1 |
ds3LbLoop-back mode active.ro Enumeration .1.3.6.1.4.1.251.1.1.13.2.1.2 |
ds3ErrAIS or BPV detected.ro Enumeration .1.3.6.1.4.1.251.1.1.13.2.1.3 |
ds3RXLosReceive loss of signal.ro Enumeration .1.3.6.1.4.1.251.1.1.13.2.1.4 |
ds3TXLocTransmit loss of clock.ro Enumeration .1.3.6.1.4.1.251.1.1.13.2.1.5 |
ds3RXErrReceive error detected.ro Enumeration .1.3.6.1.4.1.251.1.1.13.2.1.6 |
ds3RXAisSet to yes(1) to generate a receive AIS alarm.rw Enumeration .1.3.6.1.4.1.251.1.1.13.2.1.7 |
ds3TXAisSet to yes(1) to transmit an AIS alarm.rw Enumeration .1.3.6.1.4.1.251.1.1.13.2.1.8 |
ds3TXLevTransmit level.rw Enumeration .1.3.6.1.4.1.251.1.1.13.2.1.9 |
ds3TrTransmit loop-back.rw Enumeration .1.3.6.1.4.1.251.1.1.13.2.1.10 |
ds3RtSet to yes(1) to enable receive loop-back.rw Enumeration .1.3.6.1.4.1.251.1.1.13.2.1.11 |
ds3EqualEqualisation type.rw Enumeration .1.3.6.1.4.1.251.1.1.13.2.1.12 |
ds3LOSAlarmLoss Of Signal Integrated Alarmro Enumeration .1.3.6.1.4.1.251.1.1.13.2.1.13 |
ds3ReconfigReconfigure Linkrw Enumeration .1.3.6.1.4.1.251.1.1.13.2.1.14 |
e1TableE1-2C Config/Status Table SEQUENCE OF E1Entry .1.3.6.1.4.1.251.1.1.13.5 |
e1Entry E1Entry .1.3.6.1.4.1.251.1.1.13.5.1 |
e1LinkNoLink number - this is the instance.ro INTEGER .1.3.6.1.4.1.251.1.1.13.5.1.1 |
e1LimTypeLIM I.D. typero Enumeration .1.3.6.1.4.1.251.1.1.13.5.1.2 |
e1LbLoopback Selectionrw Enumeration .1.3.6.1.4.1.251.1.1.13.5.1.3 |
e1FRMRModee1 Framing options.rw Enumeration .1.3.6.1.4.1.251.1.1.13.5.1.4 |
e1TxClkSelTransmit clock select.rw Enumeration .1.3.6.1.4.1.251.1.1.13.5.1.5 |
e1TS16PayLdEmploy TimeSlot 16 for customer data.rw Enumeration .1.3.6.1.4.1.251.1.1.13.5.1.6 |
e1TxAISTransmit the AIS State.rw Enumeration .1.3.6.1.4.1.251.1.1.13.5.1.7 |
e1GappedClkSelect 1,(yes) for Circuit-emulation.rw Enumeration .1.3.6.1.4.1.251.1.1.13.5.1.8 |
e1IntrfTypeE1 Framing options.rw Enumeration .1.3.6.1.4.1.251.1.1.13.5.1.9 |
e1ClrStatsClear Countersrw Enumeration .1.3.6.1.4.1.251.1.1.13.5.1.10 |
e1ReconfigReconfigure Linkrw Enumeration .1.3.6.1.4.1.251.1.1.13.5.1.11 |
se1SA4Nat'l bit Sa4rw Enumeration .1.3.6.1.4.1.251.1.1.13.5.1.12 |
se1SA5Nat'l bit Sa5rw Enumeration .1.3.6.1.4.1.251.1.1.13.5.1.13 |
se1SA6Nat'l bit Sa6rw Enumeration .1.3.6.1.4.1.251.1.1.13.5.1.14 |
se1SA7Nat'l bit Sa7rw Enumeration .1.3.6.1.4.1.251.1.1.13.5.1.15 |
se1SA8Nat'l bit Sa8rw Enumeration .1.3.6.1.4.1.251.1.1.13.5.1.16 |
se1SI0Int'l bit Si0rw Enumeration .1.3.6.1.4.1.251.1.1.13.5.1.17 |
se1SI1Nat'l bit Si1rw Enumeration .1.3.6.1.4.1.251.1.1.13.5.1.18 |
e1LOSDefectLoss Of Signal Defectro Enumeration .1.3.6.1.4.1.251.1.1.13.5.1.22 |
e1OOFDefectReceive Out Of Framero Enumeration .1.3.6.1.4.1.251.1.1.13.5.1.23 |
e1AISDefectReceive AIS Defectro Enumeration .1.3.6.1.4.1.251.1.1.13.5.1.24 |
e1FerfDefectReceive Yellow Defectro Enumeration .1.3.6.1.4.1.251.1.1.13.5.1.25 |
e1ExBERDefectExcessive Bit Error Rate Defectro Enumeration .1.3.6.1.4.1.251.1.1.13.5.1.26 |
e1LOSAlarmLoss Of Signal Integrated Alarmro Enumeration .1.3.6.1.4.1.251.1.1.13.5.1.37 |
e1LOFAlarmLoss Of Frame Integrated Alarmro Enumeration .1.3.6.1.4.1.251.1.1.13.5.1.38 |
e1AISAlarmAIS Integrated Alarmro Enumeration .1.3.6.1.4.1.251.1.1.13.5.1.39 |
e1FerfAlarmYellow Integrated Alarmro Enumeration .1.3.6.1.4.1.251.1.1.13.5.1.40 |
e1ExBERAlarmExcessive Bit Error Rate Alarmro Enumeration .1.3.6.1.4.1.251.1.1.13.5.1.41 |
e1SCRCErrsThe CRC-4 error count for this link.ro INTEGER .1.3.6.1.4.1.251.1.1.13.5.1.52 |
e1SFrameErrsThe frame error count for this link.ro INTEGER .1.3.6.1.4.1.251.1.1.13.5.1.53 |
e1SFEBEErrsThe FEBE error count for this link.ro INTEGER .1.3.6.1.4.1.251.1.1.13.5.1.54 |
e1SLcvsThe E1 LCV count for this link.ro INTEGER .1.3.6.1.4.1.251.1.1.13.5.1.55 |
e1LineESLine Errored Secondsro Counter .1.3.6.1.4.1.251.1.1.13.5.1.66 |
e1LineSESLine Severely Errored Secondsro Counter .1.3.6.1.4.1.251.1.1.13.5.1.67 |
e1ESErrored Secondsro Counter .1.3.6.1.4.1.251.1.1.13.5.1.68 |
e1SESSeverely Errored Secondsro Counter .1.3.6.1.4.1.251.1.1.13.5.1.69 |
e1AISSAIS Secondsro Counter .1.3.6.1.4.1.251.1.1.13.5.1.70 |
e1UASUnavailable Secondsro Counter .1.3.6.1.4.1.251.1.1.13.5.1.71 |
soTableSOLIM/DELIM Status Table SEQUENCE OF SoEntry .1.3.6.1.4.1.251.1.1.13.7 |
soEntry SoEntry .1.3.6.1.4.1.251.1.1.13.7.1 |
soLinkNoLink number - this is the instance.ro INTEGER .1.3.6.1.4.1.251.1.1.13.7.1.1 |
soLimTypeSolim versionro Enumeration .1.3.6.1.4.1.251.1.1.13.7.1.2 |
soTimingRefLocal timing referencerw Enumeration .1.3.6.1.4.1.251.1.1.13.7.1.3 |
soTxEn0Link 0 Tx Enable (v2 and above)rw Enumeration .1.3.6.1.4.1.251.1.1.13.7.1.4 |
soTxEn1Link 1 Tx Enable (v2 and above)rw Enumeration .1.3.6.1.4.1.251.1.1.13.7.1.5 |
soLimDescLIM Descriptionrw Enumeration .1.3.6.1.4.1.251.1.1.13.7.1.6 |
soReconfigReconfigure Linkrw Enumeration .1.3.6.1.4.1.251.1.1.13.7.1.7 |
ds1V2Tableds1 V2 Status Table SEQUENCE OF Ds1V2Entry .1.3.6.1.4.1.251.1.1.13.9 |
ds1V2Entry Ds1V2Entry .1.3.6.1.4.1.251.1.1.13.9.1 |
ds1V2LinkNoLink number - this is the instance.ro INTEGER .1.3.6.1.4.1.251.1.1.13.9.1.1 |
ds1V2LimTypeLIM I.D. typero Enumeration .1.3.6.1.4.1.251.1.1.13.9.1.2 |
ds1V2TxLineLnSelect txmt line length.rw Enumeration .1.3.6.1.4.1.251.1.1.13.9.1.3 |
ds1V2FRMRModeds1V2 Framing options.rw Enumeration .1.3.6.1.4.1.251.1.1.13.9.1.4 |
ds1V2CodingIf Line Coding is yes(1), AMI is selectedrw Enumeration .1.3.6.1.4.1.251.1.1.13.9.1.5 |
ds1V2LbLoopback Selectionrw Enumeration .1.3.6.1.4.1.251.1.1.13.9.1.6 |
ds1V2TxAISTransmit the AIS State.rw Enumeration .1.3.6.1.4.1.251.1.1.13.9.1.7 |
ds1V2GappedClkSelect 1,(yes) for Circuit-emulation.rw Enumeration .1.3.6.1.4.1.251.1.1.13.9.1.8 |
ds1V2TxClkSelTransmit clock select.rw Enumeration .1.3.6.1.4.1.251.1.1.13.9.1.9 |
ds1V2ClrStatsClear Countersrw Enumeration .1.3.6.1.4.1.251.1.1.13.9.1.10 |
ds1V2ReconfigReconfigure Linkrw Enumeration .1.3.6.1.4.1.251.1.1.13.9.1.11 |
ds1V2LOSDefectLoss Of Signal Defectro Enumeration .1.3.6.1.4.1.251.1.1.13.9.1.22 |
ds1V2OOFDefectReceive Out Of Framero Enumeration .1.3.6.1.4.1.251.1.1.13.9.1.23 |
ds1V2AISDefectReceive AIS Defectro Enumeration .1.3.6.1.4.1.251.1.1.13.9.1.24 |
ds1V2FerfDefectReceive FERF(Yellow) Defectro Enumeration .1.3.6.1.4.1.251.1.1.13.9.1.25 |
ds1V2BERDefectExcessive Bit Error Rate Defectro Enumeration .1.3.6.1.4.1.251.1.1.13.9.1.26 |
ds1V2LOSAlarmLoss Of Signal Integrated Alarmro Enumeration .1.3.6.1.4.1.251.1.1.13.9.1.37 |
ds1V2LOFAlarmLoss Of Frame Integrated Alarmro Enumeration .1.3.6.1.4.1.251.1.1.13.9.1.38 |
ds1V2AISAlarmAIS Integrated Alarmro Enumeration .1.3.6.1.4.1.251.1.1.13.9.1.39 |
ds1V2FerfAlarmYellow Integrated Alarmro Enumeration .1.3.6.1.4.1.251.1.1.13.9.1.40 |
ds1V2BERAlarmExcessive Bit Error Rate Alarmro Enumeration .1.3.6.1.4.1.251.1.1.13.9.1.41 |
ds1V2FerCountThe framing bit error count for this link.ro INTEGER .1.3.6.1.4.1.251.1.1.13.9.1.52 |
ds1V2BeeCountThe bit error count for this link.ro INTEGER .1.3.6.1.4.1.251.1.1.13.9.1.53 |
ds1V2OCfCountThe Out-of-frame or Change of Frame alignment error count for this link.ro INTEGER .1.3.6.1.4.1.251.1.1.13.9.1.54 |
ds1V2LcvCountThe DS1 Line code violations count for this link.ro INTEGER .1.3.6.1.4.1.251.1.1.13.9.1.55 |
ds1V2LineESLine Errored Secondsro Counter .1.3.6.1.4.1.251.1.1.13.9.1.66 |
ds1V2LineSESLine Severely Errored Secondsro Counter .1.3.6.1.4.1.251.1.1.13.9.1.67 |
ds1V2ESErrored Secondsro Counter .1.3.6.1.4.1.251.1.1.13.9.1.68 |
ds1V2SESSeverely Errored Secondsro Counter .1.3.6.1.4.1.251.1.1.13.9.1.69 |
ds1V2AISSAIS Secondsro Counter .1.3.6.1.4.1.251.1.1.13.9.1.70 |
ds1V2UASUnavailable Secondsro Counter .1.3.6.1.4.1.251.1.1.13.9.1.71 |
ds1V2ExBERExcessive Bit Error Ratero Counter .1.3.6.1.4.1.251.1.1.13.9.1.72 |
dlimLpbkTimeoutThis parameter is used to set the dlim loopback timeout in minutes.rw INTEGER .1.3.6.1.4.1.251.1.1.13.10 |
ds3V2Tableds3-2C Config/Status Table SEQUENCE OF Ds3V2Entry .1.3.6.1.4.1.251.1.1.13.11 |
ds3V2Entry Ds3V2Entry .1.3.6.1.4.1.251.1.1.13.11.1 |
ds3V2LinkNoLink number - this is the instance.ro INTEGER .1.3.6.1.4.1.251.1.1.13.11.1.1 |
ds3V2LbLoopback Activerw Enumeration .1.3.6.1.4.1.251.1.1.13.11.1.2 |
ds3V2LimTypeLIM I.D. typero Enumeration .1.3.6.1.4.1.251.1.1.13.11.1.3 |
ds3V2LimOKLIM OK.ro Enumeration .1.3.6.1.4.1.251.1.1.13.11.1.4 |
ds3V2TxLBOTransmit line build-out,(1)for short cables.rw Enumeration .1.3.6.1.4.1.251.1.1.13.11.1.5 |
ds3V2TxClkSelTransmit clock select.rw Enumeration .1.3.6.1.4.1.251.1.1.13.11.1.6 |
ds3V2LOSDefectLoss Of Signal Defectro Enumeration .1.3.6.1.4.1.251.1.1.13.11.1.8 |
ds3V2LOSAlarmLoss Of Signal Alarmro Enumeration .1.3.6.1.4.1.251.1.1.13.11.1.9 |
ds3V2ReconfigReconfigure Linkrw Enumeration .1.3.6.1.4.1.251.1.1.13.11.1.10 |
e3TableE3-2C Config/Status Table SEQUENCE OF E3Entry .1.3.6.1.4.1.251.1.1.13.12 |
e3Entry E3Entry .1.3.6.1.4.1.251.1.1.13.12.1 |
e3LinkNoLink number - this is the instance.ro INTEGER .1.3.6.1.4.1.251.1.1.13.12.1.1 |
e3LimTypeLIM I.D. typero Enumeration .1.3.6.1.4.1.251.1.1.13.12.1.2 |
e3LimOKLIM OK.ro Enumeration .1.3.6.1.4.1.251.1.1.13.12.1.3 |
e3EQSelectRx Line Equalization select.rw Enumeration .1.3.6.1.4.1.251.1.1.13.12.1.4 |
e3LoopbackLoopback LIU.rw Enumeration .1.3.6.1.4.1.251.1.1.13.12.1.6 |
e3TxAISTransmit AIS.rw Enumeration .1.3.6.1.4.1.251.1.1.13.12.1.7 |
e3TxClkSelTransmit clock select.rw Enumeration .1.3.6.1.4.1.251.1.1.13.12.1.8 |
e3LOSDefectLoss Of Signal Defectro Enumeration .1.3.6.1.4.1.251.1.1.13.12.1.9 |
e3LOSAlarmLoss Of Signal Alarmro Enumeration .1.3.6.1.4.1.251.1.1.13.12.1.10 |
e3ReconfigReconfigure Linkrw Enumeration .1.3.6.1.4.1.251.1.1.13.12.1.11 |
hssiTablehssi Status Table SEQUENCE OF HssiEntry .1.3.6.1.4.1.251.1.1.13.13 |
hssiEntry HssiEntry .1.3.6.1.4.1.251.1.1.13.13.1 |
hssiLinkNoLink number - this is the instance.ro INTEGER .1.3.6.1.4.1.251.1.1.13.13.1.1 |
hssiLocalLoopbackLocal Loopback.rw Enumeration .1.3.6.1.4.1.251.1.1.13.13.1.2 |
hssiRemoteLoopbackRemote Loopback.rw Enumeration .1.3.6.1.4.1.251.1.1.13.13.1.3 |
hssiReconfigReconfigure Linkrw Enumeration .1.3.6.1.4.1.251.1.1.13.13.1.4 |
hssiTypeType of link.rw Enumeration .1.3.6.1.4.1.251.1.1.13.13.1.15 |
hssiLimTypeLIM Versionro Enumeration .1.3.6.1.4.1.251.1.1.13.13.1.16 |
hssiClockSrcSource of clock. Note that for a DCE, from-DCE(4) should not be selected.rw Enumeration .1.3.6.1.4.1.251.1.1.13.13.1.17 |
hssiCtrTestModeTest Mode.ro Enumeration .1.3.6.1.4.1.251.1.1.13.13.1.18 |
hssiLinkReadySet to yes(1) if link is ready.ro Enumeration .1.3.6.1.4.1.251.1.1.13.13.1.19 |
hssiRemoteReadySet to yes(1) if remote link is ready.ro Enumeration .1.3.6.1.4.1.251.1.1.13.13.1.20 |
hssiLOSDefectLoss Of Signal Defectro Enumeration .1.3.6.1.4.1.251.1.1.13.13.1.25 |
hssiLOSAlarmLoss Of Signal Alarmro Enumeration .1.3.6.1.4.1.251.1.1.13.13.1.30 |
j2TableJ2 Config/Status Table SEQUENCE OF J2Entry .1.3.6.1.4.1.251.1.1.13.14 |
j2Entry J2Entry .1.3.6.1.4.1.251.1.1.13.14.1 |
j2LinkNoLink number - this is the instance.ro INTEGER .1.3.6.1.4.1.251.1.1.13.14.1.1 |
j2FirmwareRevFirmware Revisionro INTEGER .1.3.6.1.4.1.251.1.1.13.14.1.3 |
j2TxEqSelect equalizer settingrw Enumeration .1.3.6.1.4.1.251.1.1.13.14.1.4 |
j2LbLoopback Selectionrw Enumeration .1.3.6.1.4.1.251.1.1.13.14.1.6 |
j2TxAISTransmit the AIS State.rw Enumeration .1.3.6.1.4.1.251.1.1.13.14.1.7 |
j2TxClkSelTransmit clock select.rw Enumeration .1.3.6.1.4.1.251.1.1.13.14.1.9 |
j2ClrStatsClear Countersrw Enumeration .1.3.6.1.4.1.251.1.1.13.14.1.10 |
j2ReconfigReconfigure Linkrw Enumeration .1.3.6.1.4.1.251.1.1.13.14.1.11 |
j2TS97TS98Set the value (in hex) of the bytes to be transmitted in time slots 97 and 98 of the J2 frame.rw Hex .1.3.6.1.4.1.251.1.1.13.14.1.12 |
j2QualClockQuality of Clock Selectionro Enumeration .1.3.6.1.4.1.251.1.1.13.14.1.20 |
j2LOSDefectLoss Of Signal Defectro Enumeration .1.3.6.1.4.1.251.1.1.13.14.1.22 |
j2OOFDefectReceive Out Of Framero Enumeration .1.3.6.1.4.1.251.1.1.13.14.1.23 |
j2AISDefectReceive AIS Defectro Enumeration .1.3.6.1.4.1.251.1.1.13.14.1.24 |
j2RAlmDefectRemote Alarm Defectro Enumeration .1.3.6.1.4.1.251.1.1.13.14.1.26 |
j2LOSAlarmLoss Of Signal Integrated Alarmro Enumeration .1.3.6.1.4.1.251.1.1.13.14.1.37 |
j2LOFAlarmLoss Of Frame Integrated Alarmro Enumeration .1.3.6.1.4.1.251.1.1.13.14.1.38 |
j2AISAlarmAIS Integrated Alarmro Enumeration .1.3.6.1.4.1.251.1.1.13.14.1.39 |
j2RAlmAlarmRemote Alarm Conditionro Enumeration .1.3.6.1.4.1.251.1.1.13.14.1.41 |
j2FerCountThe framing bit error count for this link.ro INTEGER .1.3.6.1.4.1.251.1.1.13.14.1.52 |
j2RAlmCountThe Remote Alarm error count for this link.ro INTEGER .1.3.6.1.4.1.251.1.1.13.14.1.53 |
j2LcvCountThe J2 Line code violations count for this link.ro INTEGER .1.3.6.1.4.1.251.1.1.13.14.1.55 |
j2CrcCountNumber of J2 muliframes received with CRC errorsro Counter .1.3.6.1.4.1.251.1.1.13.14.1.56 |
j2LineESLine Errored Secondsro Counter .1.3.6.1.4.1.251.1.1.13.14.1.66 |
j2LineSESLine Severely Errored Secondsro Counter .1.3.6.1.4.1.251.1.1.13.14.1.67 |
j2ESErrored Secondsro Counter .1.3.6.1.4.1.251.1.1.13.14.1.68 |
j2SESSeverely Errored Secondsro Counter .1.3.6.1.4.1.251.1.1.13.14.1.69 |
j2AISSAIS Secondsro Counter .1.3.6.1.4.1.251.1.1.13.14.1.70 |
j2UASUnavailable Secondsro Counter .1.3.6.1.4.1.251.1.1.13.14.1.71 |
scfTableSCF Config/Status Table SEQUENCE OF ScfEntry .1.3.6.1.4.1.251.1.1.13.15 |
scfEntry ScfEntry .1.3.6.1.4.1.251.1.1.13.15.1 |
scfLinkNoLink number - this is the instance.ro INTEGER .1.3.6.1.4.1.251.1.1.13.15.1.1 |
scfLimTypeLIM I.D. typero Enumeration .1.3.6.1.4.1.251.1.1.13.15.1.2 |
scfFirmwareRevFirmware Revisionro INTEGER .1.3.6.1.4.1.251.1.1.13.15.1.3 |
scfQualClockQuality of Clock Selectionro Enumeration .1.3.6.1.4.1.251.1.1.13.15.1.4 |
scfContrController Selectionrw Enumeration .1.3.6.1.4.1.251.1.1.13.15.1.5 |
scfDCEDTEDCE or DTE Selectionrw Enumeration .1.3.6.1.4.1.251.1.1.13.15.1.6 |
scfLbLoopback Selectionrw Enumeration .1.3.6.1.4.1.251.1.1.13.15.1.7 |
scfLineTimingReceive Line Timing Selectionrw Enumeration .1.3.6.1.4.1.251.1.1.13.15.1.8 |
scfDataRateData Rate Selection in K Bit/Secrw Enumeration .1.3.6.1.4.1.251.1.1.13.15.1.9 |
scfClkSelClock selectrw Enumeration .1.3.6.1.4.1.251.1.1.13.15.1.10 |
scfInterfaceTypeInterface type selectionrw Enumeration .1.3.6.1.4.1.251.1.1.13.15.1.11 |
scfReconfigReconfigure Linkrw Enumeration .1.3.6.1.4.1.251.1.1.13.15.1.12 |
scfLOSDefectLoss Of Signal Defectro Enumeration .1.3.6.1.4.1.251.1.1.13.15.1.13 |
scfLOSAlarmLoss Of Signal Integrated Alarmro Enumeration .1.3.6.1.4.1.251.1.1.13.15.1.14 |
dv2Billing OBJECT IDENTIFIER .1.3.6.1.4.1.251.1.1.14 |
billAvailableNumber of billing records available.ro INTEGER .1.3.6.1.4.1.251.1.1.14.1 |
billingTableThis table is used to contain billing records. SEQUENCE OF BillingEntry .1.3.6.1.4.1.251.1.1.14.3 |
billingEntry BillingEntry .1.3.6.1.4.1.251.1.1.14.3.1 |
billSeqbilling record sequence number.ro INTEGER .1.3.6.1.4.1.251.1.1.14.3.1.1 |
billSvpiSource Virtual Path Identifier for VC.ro VirtualPathIdentifier .1.3.6.1.4.1.251.1.1.14.3.1.2 |
billSvciSource Virtual Circuit Identifier for VC.ro VirtualCircuitIdentifier .1.3.6.1.4.1.251.1.1.14.3.1.3 |
billDvpiDestination Virtual Path Identifier for VC.ro VirtualPathIdentifier .1.3.6.1.4.1.251.1.1.14.3.1.4 |
billDvciDestination Virtual Circuit Identifier for VC.ro VirtualCircuitIdentifier .1.3.6.1.4.1.251.1.1.14.3.1.5 |
billSslotSource slot for VC.ro INTEGER .1.3.6.1.4.1.251.1.1.14.3.1.6 |
billSlinkSource link for VC.ro INTEGER .1.3.6.1.4.1.251.1.1.14.3.1.7 |
billDslotDestination slot for VC.ro INTEGER .1.3.6.1.4.1.251.1.1.14.3.1.8 |
billDlinkDestination link for VC.ro INTEGER .1.3.6.1.4.1.251.1.1.14.3.1.9 |
billCalledCalled or Destination E.164 address.ro E164 .1.3.6.1.4.1.251.1.1.14.3.1.10 |
billCalledSubCalled or Destination E.164 sub-address.ro E164SUB .1.3.6.1.4.1.251.1.1.14.3.1.11 |
billCallingCalling or Originating E.164 address.ro E164 .1.3.6.1.4.1.251.1.1.14.3.1.12 |
billCallingSubCalling or Originating E.164 sub-address.ro E164SUB .1.3.6.1.4.1.251.1.1.14.3.1.13 |
billCellInCCell in overflows count.ro Counter .1.3.6.1.4.1.251.1.1.14.3.1.14 |
billCellInCell in count.ro Counter .1.3.6.1.4.1.251.1.1.14.3.1.15 |
billFrameInFrame in count.ro Counter .1.3.6.1.4.1.251.1.1.14.3.1.16 |
billByteInCByte in overflows count.ro Counter .1.3.6.1.4.1.251.1.1.14.3.1.17 |
billByteInByte in count.ro Counter .1.3.6.1.4.1.251.1.1.14.3.1.18 |
billCellOutCCell out overflows count.ro Counter .1.3.6.1.4.1.251.1.1.14.3.1.19 |
billCellOutCell out count.ro Counter .1.3.6.1.4.1.251.1.1.14.3.1.20 |
billFrameOutFrame out count.ro Counter .1.3.6.1.4.1.251.1.1.14.3.1.21 |
billByteOutCByte out overflows count.ro Counter .1.3.6.1.4.1.251.1.1.14.3.1.22 |
billByteOutByte out count.ro Counter .1.3.6.1.4.1.251.1.1.14.3.1.23 |
billCauseClear cause code.ro INTEGER .1.3.6.1.4.1.251.1.1.14.3.1.25 |
billValidDeletes billing record Entry by setting to invalid(2).rw Enumeration .1.3.6.1.4.1.251.1.1.14.3.1.28 |
billCLP1OutCCLP1 out overflows count.ro Counter .1.3.6.1.4.1.251.1.1.14.3.1.29 |
billCLP1OutCLP1 out count.ro Counter .1.3.6.1.4.1.251.1.1.14.3.1.30 |
billTagThis identifies the billable SVC.ro INTEGER .1.3.6.1.4.1.251.1.1.14.3.1.31 |
billStartM2Call start date-time.ro DateAndTime (SNMPv2-TC) .1.3.6.1.4.1.251.1.1.14.3.1.32 |
billEndM2Call end date-time.ro DateAndTime (SNMPv2-TC) .1.3.6.1.4.1.251.1.1.14.3.1.33 |
billFwdPCRSVC Forward Peak Cell Rate.ro INTEGER .1.3.6.1.4.1.251.1.1.14.3.1.34 |
billBwdPCRSVC Backward Peak Cell Rate.ro INTEGER .1.3.6.1.4.1.251.1.1.14.3.1.35 |
billFwdSCRSVC Forward Sustained Cell Rate.ro INTEGER .1.3.6.1.4.1.251.1.1.14.3.1.36 |
billBwdSCRSVC Backward Sustained Cell Rate.ro INTEGER .1.3.6.1.4.1.251.1.1.14.3.1.37 |
billFwdMBSSVC Forward Maximum Burst Size.ro INTEGER .1.3.6.1.4.1.251.1.1.14.3.1.38 |
billBwdMBSSVC Backward Maximum Burst Size.ro INTEGER .1.3.6.1.4.1.251.1.1.14.3.1.39 |
billFwdQOSForward Quality of Service.ro Enumeration .1.3.6.1.4.1.251.1.1.14.3.1.40 |
billBwdQOSBackward Quality of Service.ro Enumeration .1.3.6.1.4.1.251.1.1.14.3.1.41 |
billingControlThis object is set to start SPVC/PVC process.rw Enumeration .1.3.6.1.4.1.251.1.1.14.4 |
billLostLost of billing record count.rw Counter .1.3.6.1.4.1.251.1.1.14.7 |
billLinksThis value is bitwise billing link control.rw Enumeration .1.3.6.1.4.1.251.1.1.14.8 |
billTrapControlThis object is set to enable or disable billing trapsrw Enumeration .1.3.6.1.4.1.251.1.1.14.9 |
billDirControlThis object is selected for uni-direction billing or bi-direction billing.rw Enumeration .1.3.6.1.4.1.251.1.1.14.10 |
billingIntervalThis parameter is used to set the billing period in 15/30/60/120 minute intervalsrw Enumeration .1.3.6.1.4.1.251.1.1.14.12 |
dv2QeDoc OBJECT IDENTIFIER .1.3.6.1.4.1.251.1.1.15 |
qeDocMacAddressMAC address of Ethernet ports.ro PhysAddress (SNMPv2-TC) .1.3.6.1.4.1.251.1.1.15.1 |
qeDocTunRetryPeriodNumber of seconds between retries of tunnel establishment.rw INTEGER .1.3.6.1.4.1.251.1.1.15.2 |
qeDocTunIdlePeriodNumber of seconds to wait without activity before clearing tunnel call.rw INTEGER .1.3.6.1.4.1.251.1.1.15.3 |
qeDocBridgeTableThis table is used to statistics and control for the bridges. SEQUENCE OF QeDocBridgeEntry .1.3.6.1.4.1.251.1.1.15.4 |
qeDocBridgeEntry QeDocBridgeEntry .1.3.6.1.4.1.251.1.1.15.4.1 |
qeDocBridgeLinkNoLink number.ro INTEGER .1.3.6.1.4.1.251.1.1.15.4.1.1 |
qeDocBridgeEnableSet to yes(1) to enable MAC bridging.rw Enumeration .1.3.6.1.4.1.251.1.1.15.4.1.2 |
qeDocBridgeLink0EligibleLink 0 eligible for framesrw Enumeration .1.3.6.1.4.1.251.1.1.15.4.1.3 |
qeDocBridgeLink1EligibleLink 1 eligible for framesrw Enumeration .1.3.6.1.4.1.251.1.1.15.4.1.4 |
qeDocBridgeLink2EligibleLink 2 eligible for framesrw Enumeration .1.3.6.1.4.1.251.1.1.15.4.1.5 |
qeDocBridgeLink3EligibleLink 3 eligible for framesrw Enumeration .1.3.6.1.4.1.251.1.1.15.4.1.6 |
qeDocTunTableThis table is used to establish and control tunnels set-up using SVCs. SEQUENCE OF QeDocTunEntry .1.3.6.1.4.1.251.1.1.15.6 |
qeDocTunEntry QeDocTunEntry .1.3.6.1.4.1.251.1.1.15.6.1 |
qeDocTunIndexThe tunnel index number.rw INTEGER .1.3.6.1.4.1.251.1.1.15.6.1.1 |
qeDocTunNameMnemonic name for tunnel.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.251.1.1.15.6.1.2 |
qeDocTunTypeSpecifies the type of tunnel.rw Enumeration .1.3.6.1.4.1.251.1.1.15.6.1.3 |
qeDocTunStateSet to Use pvc(2) if using with a PVC. Set to Use svc(3) if using with a SVC. Set to idle(1) to prevent tunnel being established.rw Enumeration .1.3.6.1.4.1.251.1.1.15.6.1.4 |
qeDocTunCallStateState of tunnel call.ro Enumeration .1.3.6.1.4.1.251.1.1.15.6.1.5 |
qeDocTunInFramesReceived frames count.ro Counter .1.3.6.1.4.1.251.1.1.15.6.1.6 |
qeDocTunOutFramesTransmitted frames count.ro Counter .1.3.6.1.4.1.251.1.1.15.6.1.7 |
qeDocTunVPIVPI being used for the tunnel.ro VirtualPathIdentifier .1.3.6.1.4.1.251.1.1.15.6.1.8 |
qeDocTunVCIVCI being used for the tunnel.ro VirtualCircuitIdentifier .1.3.6.1.4.1.251.1.1.15.6.1.9 |
qeDocTunPriorityCell priority bit value.ro INTEGER .1.3.6.1.4.1.251.1.1.15.6.1.10 |
qeDocTunSlotTarget slot for tunnel.ro INTEGER .1.3.6.1.4.1.251.1.1.15.6.1.11 |
qeDocTunLinkTarget link for tunnel.ro INTEGER .1.3.6.1.4.1.251.1.1.15.6.1.12 |
qeDocTunRemNetRemote network address for tunnel.rw IpAddress .1.3.6.1.4.1.251.1.1.15.6.1.13 |
qeDocTunRemMaskMask for remote network.rw IpAddress .1.3.6.1.4.1.251.1.1.15.6.1.14 |
qeDocTunLocNetLocal network address for tunnel.rw IpAddress .1.3.6.1.4.1.251.1.1.15.6.1.15 |
qeDocTunLocMaskMask for local network.rw IpAddress .1.3.6.1.4.1.251.1.1.15.6.1.16 |
qeDocTunRemStartSktSpecifies start of socket range from remote that is allowed/barred from access to tunnel.rw INTEGER .1.3.6.1.4.1.251.1.1.15.6.1.17 |
qeDocTunRemEndSktSpecifies end of socket range from remote that is allowed/barred from access to tunnel.rw INTEGER .1.3.6.1.4.1.251.1.1.15.6.1.18 |
qeDocTunLocStartSktSpecifies start of socket range from local that is allowed/barred from access to tunnel.rw INTEGER .1.3.6.1.4.1.251.1.1.15.6.1.19 |
qeDocTunLocEndSktSpecifies end of socket range from local that is allowed/barred from access to tunnel.rw INTEGER .1.3.6.1.4.1.251.1.1.15.6.1.20 |
qeDocTunSktTypeSpecifies the protocol type and whether to include or exclude frames with socket number in the specified range.rw Enumeration .1.3.6.1.4.1.251.1.1.15.6.1.21 |
qeDocTunDestAddressDestination address for tunnel. This is only required for SVC tunnels.rw E164 .1.3.6.1.4.1.251.1.1.15.6.1.22 |
qeDocTunDestSubAddressDestination sub-address for tunnel. This is only required for SVC tunnels.rw E164SUB .1.3.6.1.4.1.251.1.1.15.6.1.23 |
qeDocTunLink0EligibleLink 0 eligible for framesrw Enumeration .1.3.6.1.4.1.251.1.1.15.6.1.24 |
qeDocTunLink1EligibleLink 1 eligible for framesrw Enumeration .1.3.6.1.4.1.251.1.1.15.6.1.25 |
qeDocTunLink2EligibleLink 2 eligible for framesrw Enumeration .1.3.6.1.4.1.251.1.1.15.6.1.26 |
qeDocTunLink3EligibleLink 3 eligible for framesrw Enumeration .1.3.6.1.4.1.251.1.1.15.6.1.27 |
qeDocTunValiditySetting to invalid(2) removes the row from the table.rw Enumeration .1.3.6.1.4.1.251.1.1.15.6.1.28 |
qeDocTunRfc1483EncapSetting to yes(1) enable RFC 1483 LLC encapsulation.rw Enumeration .1.3.6.1.4.1.251.1.1.15.6.1.29 |
qeDocTunClpCell loss priority bit value.ro INTEGER .1.3.6.1.4.1.251.1.1.15.6.1.31 |
qeDocIpAddressThe IP address of the QEDOC for management use.rw IpAddress .1.3.6.1.4.1.251.1.1.15.7 |
qeDocIpMaskThe mask for management use.rw IpAddress .1.3.6.1.4.1.251.1.1.15.8 |
qeDocIpBCastThe management broadcast address.rw IpAddress .1.3.6.1.4.1.251.1.1.15.9 |
dv2SDH OBJECT IDENTIFIER .1.3.6.1.4.1.251.1.1.16 |
sdhCTableThis table is used to control sdh/Sonet configuration. SEQUENCE OF SdhCEntry .1.3.6.1.4.1.251.1.1.16.1 |
sdhCEntry SdhCEntry .1.3.6.1.4.1.251.1.1.16.1.1 |
sdhCLinkNoThe link number for this configuration.ro INTEGER .1.3.6.1.4.1.251.1.1.16.1.1.1 |
sdhCLinkEnabSet to yes(1) to enable the link.rw Enumeration .1.3.6.1.4.1.251.1.1.16.1.1.2 |
sdhCLoopTimerSet to yes(1) to enable loop timing for this link.rw Enumeration .1.3.6.1.4.1.251.1.1.16.1.1.3 |
sdhCLoopDiagSet to yes(1) to enable diagnostic loopback.rw Enumeration .1.3.6.1.4.1.251.1.1.16.1.1.4 |
sdhCLoopLineSet to yes(1) to enable line loopback.rw Enumeration .1.3.6.1.4.1.251.1.1.16.1.1.5 |
sdhCScramblerSet to no(2) to disable scramble mode for this link.rw Enumeration .1.3.6.1.4.1.251.1.1.16.1.1.6 |
sdhC0x55If set to no(2) then HCS is XORed with 0x55rw Enumeration .1.3.6.1.4.1.251.1.1.16.1.1.7 |
sdhSonetSdhIf set to sdh(2) then sdh header is usedrw Enumeration .1.3.6.1.4.1.251.1.1.16.1.1.8 |
sdhClearCountsClear Error Counts and Performance Parametersrw Enumeration .1.3.6.1.4.1.251.1.1.16.1.1.9 |
sdhReconfigPerform Reconfiguration for Linkrw Enumeration .1.3.6.1.4.1.251.1.1.16.1.1.10 |
sdhCLpbkTimeoutThis parameter is used to set the loopback timeout in minutes.rw INTEGER .1.3.6.1.4.1.251.1.1.16.1.1.11 |
sdhStmStsSet to 155.52(1) for STS-3c/STM-1 formatrw Enumeration .1.3.6.1.4.1.251.1.1.16.1.1.12 |
sdhAPSOnOffIf set to on(2) then sdh APS is usedrw Enumeration .1.3.6.1.4.1.251.1.1.16.1.1.13 |
sdhCIdleCellIdle Cell Header Contentsrw Enumeration .1.3.6.1.4.1.251.1.1.16.1.1.14 |
sdhSTableThe status table for sdh/SONET. SEQUENCE OF SdhSEntry .1.3.6.1.4.1.251.1.1.16.3 |
sdhSEntry SdhSEntry .1.3.6.1.4.1.251.1.1.16.3.1 |
sdhSLinkNoThe link number for this status.ro INTEGER .1.3.6.1.4.1.251.1.1.16.3.1.1 |
sdhSTXclockThe state of TX clock for this link.ro Enumeration .1.3.6.1.4.1.251.1.1.16.3.1.2 |
sdhSRXclockThe state of RX clock for this link.ro Enumeration .1.3.6.1.4.1.251.1.1.16.3.1.3 |
sdhSSectLOSThe loss of signal indicator.ro Enumeration .1.3.6.1.4.1.251.1.1.16.3.1.4 |
sdhSSectOOFThe out of frame indicator.ro Enumeration .1.3.6.1.4.1.251.1.1.16.3.1.5 |
sdhSSectLOFThe loss of frame indicator.ro Enumeration .1.3.6.1.4.1.251.1.1.16.3.1.6 |
sdhSLineAISSet to yes(1) if Line AIS detected.ro Enumeration .1.3.6.1.4.1.251.1.1.16.3.1.7 |
sdhSLineFERFSet to yes(1) if Line FERF detected.ro Enumeration .1.3.6.1.4.1.251.1.1.16.3.1.8 |
sdhSPathAISSet to yes(1) if Alarm Indication Signal detected.ro Enumeration .1.3.6.1.4.1.251.1.1.16.3.1.9 |
sdhSPathYellowSet to yes(1) if yellow alarm active.ro Enumeration .1.3.6.1.4.1.251.1.1.16.3.1.10 |
sdhSPathFERFSet to yes(1) if Far End Receive Failure detected.ro Enumeration .1.3.6.1.4.1.251.1.1.16.3.1.11 |
sdhSPathLOPSet to yes(1) if Loss Of Pointer detected.ro Enumeration .1.3.6.1.4.1.251.1.1.16.3.1.12 |
sdhSPathLabelMMSet to yes(1) if a Path Label Mismatch is detectedro Enumeration .1.3.6.1.4.1.251.1.1.16.3.1.13 |
sdhSExBERDefectExcessive Bit Error Rate Defectro Enumeration .1.3.6.1.4.1.251.1.1.16.3.1.14 |
sdhSPathLabelThe Path Label.ro Enumeration .1.3.6.1.4.1.251.1.1.16.3.1.15 |
sdhSCellDelStateThe Cell Delineation Statero Enumeration .1.3.6.1.4.1.251.1.1.16.3.1.16 |
sdhSAlarmLOSSet to yes(1) if a LOS failure is declaredro Enumeration .1.3.6.1.4.1.251.1.1.16.3.1.17 |
sdhSAlarmLOFSet to yes(1) if a LOF failure is declaredro Enumeration .1.3.6.1.4.1.251.1.1.16.3.1.18 |
sdhSAlarmLineAISSet to yes(1) if a Line AIS failure is declaredro Enumeration .1.3.6.1.4.1.251.1.1.16.3.1.19 |
sdhSAlarmLineRFISet to yes(1) if a Line Remote Failure Indication (Yellow Alarm) failure is declaredro Enumeration .1.3.6.1.4.1.251.1.1.16.3.1.20 |
sdhSAlarmPathAISSet to yes(1) if a Path AIS failure is declaredro Enumeration .1.3.6.1.4.1.251.1.1.16.3.1.21 |
sdhSAlarmPathRFISet to yes(1) if a Path Remote Failure Indication (Yellow Alarm) failure is declaredro Enumeration .1.3.6.1.4.1.251.1.1.16.3.1.22 |
sdhSAlarmLOPSet to yes(1) if a LOP failure is declaredro Enumeration .1.3.6.1.4.1.251.1.1.16.3.1.23 |
sdhSAlarmPLMSet to yes(1) if a Payload Mismatch failure is declaredro Enumeration .1.3.6.1.4.1.251.1.1.16.3.1.24 |
sdhSExBERAlarmExcessive Bit Error Rate Alarmro Enumeration .1.3.6.1.4.1.251.1.1.16.3.1.25 |
sdhSCorrHCSThe correctable HCS errors count.ro Counter .1.3.6.1.4.1.251.1.1.16.3.1.26 |
sdhSUnCorrHCSThe uncorrectable HCS errors count.ro Counter .1.3.6.1.4.1.251.1.1.16.3.1.27 |
sdhS2TableThe second status table for sdh/SONET. SEQUENCE OF SdhS2Entry .1.3.6.1.4.1.251.1.1.16.4 |
sdhS2Entry SdhS2Entry .1.3.6.1.4.1.251.1.1.16.4.1 |
sdhS2LinkNoThe link number for this status.ro INTEGER .1.3.6.1.4.1.251.1.1.16.4.1.1 |
sdhSSectBIP8Section BIP-8 error count.ro Counter .1.3.6.1.4.1.251.1.1.16.4.1.2 |
sdhSSectESSection Errored Secondsro Counter .1.3.6.1.4.1.251.1.1.16.4.1.3 |
sdhSSectSESSection Severely Errored Secondsro Counter .1.3.6.1.4.1.251.1.1.16.4.1.4 |
sdhSLineBIP24Line BIP-24 error count.ro Counter .1.3.6.1.4.1.251.1.1.16.4.1.5 |
sdhSLineESLine Errored Secondsro Counter .1.3.6.1.4.1.251.1.1.16.4.1.6 |
sdhSLineSESLine Severely Errored Secondsro Counter .1.3.6.1.4.1.251.1.1.16.4.1.7 |
sdhSLineUASLine Unavailable Secondsro Counter .1.3.6.1.4.1.251.1.1.16.4.1.8 |
sdhSLineFCLine Failure Countro Counter .1.3.6.1.4.1.251.1.1.16.4.1.9 |
sdhSPathBIP8The path BIP-8 count.ro Counter .1.3.6.1.4.1.251.1.1.16.4.1.10 |
sdhSPathESPath Errored Secondsro Counter .1.3.6.1.4.1.251.1.1.16.4.1.11 |
sdhSPathSESPath Severely Errored Secondsro Counter .1.3.6.1.4.1.251.1.1.16.4.1.12 |
sdhSPathUASPath Unavailable Secondsro Counter .1.3.6.1.4.1.251.1.1.16.4.1.13 |
sdhSPathFCPath Failure Countro Counter .1.3.6.1.4.1.251.1.1.16.4.1.14 |
sdhSLineFEBEFar end block errors.ro Counter .1.3.6.1.4.1.251.1.1.16.4.1.15 |
sdhSLineFarEndESFar End Line Errored Secondsro Counter .1.3.6.1.4.1.251.1.1.16.4.1.16 |
sdhSLineFarEndSESFar End Line Severely Errored Secondsro Counter .1.3.6.1.4.1.251.1.1.16.4.1.17 |
sdhSLineFarEndUASFar End Line Unavailable Secondsro Counter .1.3.6.1.4.1.251.1.1.16.4.1.18 |
sdhSLineFarEndFCFar End Line Failure Countro Counter .1.3.6.1.4.1.251.1.1.16.4.1.19 |
sdhSPathFEBEThe Path Far End Block Error count.ro Counter .1.3.6.1.4.1.251.1.1.16.4.1.20 |
sdhSPathFarEndESFar End Path Errored Secondro Counter .1.3.6.1.4.1.251.1.1.16.4.1.21 |
sdhSPathFarEndSESFar End Path Severely Errored Secondsro Counter .1.3.6.1.4.1.251.1.1.16.4.1.22 |
sdhSPathFarEndUASFar End Path Unavailable Secondsro Counter .1.3.6.1.4.1.251.1.1.16.4.1.23 |
sdhSPathFarEndFCFar End Path Failure Countro Counter .1.3.6.1.4.1.251.1.1.16.4.1.24 |
dv2Pvc OBJECT IDENTIFIER .1.3.6.1.4.1.251.1.1.17 |
pvcResourceTableThis table contains information about the resource available for pvcs on each link. SEQUENCE OF PvcResourceEntry .1.3.6.1.4.1.251.1.1.17.1 |
pvcResourceEntry PvcResourceEntry .1.3.6.1.4.1.251.1.1.17.1.1 |
pvcSlotThe slot number.ro INTEGER .1.3.6.1.4.1.251.1.1.17.1.1.1 |
pvcLinkThe link number being used for the call.ro INTEGER .1.3.6.1.4.1.251.1.1.17.1.1.2 |
pvcVciStartIdentifies the start of the range of PVC VCI values supported on this link.rw VirtualCircuitIdentifier .1.3.6.1.4.1.251.1.1.17.1.1.3 |
pvcVciEndIdentifies the end of the range of PVC VCI values supported on this link.rw VirtualCircuitIdentifier .1.3.6.1.4.1.251.1.1.17.1.1.4 |
pvcVpiStartIdentifies the start of the range of PVC VPI values supported on this link.rw VirtualPathIdentifier .1.3.6.1.4.1.251.1.1.17.1.1.5 |
pvcVpiEndIdentifies the end of the range of PVC VPI values supported on this link.rw VirtualPathIdentifier .1.3.6.1.4.1.251.1.1.17.1.1.6 |
pvcVpStartIdentifies the start of the range of VPs supported on this link.rw VirtualPathIdentifier .1.3.6.1.4.1.251.1.1.17.1.1.7 |
pvcVpEndIdentifies the end of the range of VPs supported on this link.rw VirtualPathIdentifier .1.3.6.1.4.1.251.1.1.17.1.1.8 |
pvcBackwardCellRateTotalThe backward total cell rate configured for PVCs on this link. Note that this object is in cells per second (CPS).rw INTEGER .1.3.6.1.4.1.251.1.1.17.1.1.11 |
pvcLinkQoSThis specifies the type of ATM link.rw Enumeration .1.3.6.1.4.1.251.1.1.17.1.1.13 |
pvcMolnVpiThis is the VPI for the management overlay network.rw INTEGER .1.3.6.1.4.1.251.1.1.17.1.1.14 |
pvcMolnVciThis is the VCI for the management overlay network.rw INTEGER .1.3.6.1.4.1.251.1.1.17.1.1.15 |
pvcLowPriOverbookFactorThis is the percentage of low priority traffic overbook factor.rw INTEGER .1.3.6.1.4.1.251.1.1.17.1.1.16 |
pvcTableThis table contains information on each PVC. SEQUENCE OF PvcEntry .1.3.6.1.4.1.251.1.1.17.2 |
pvcEntry PvcEntry .1.3.6.1.4.1.251.1.1.17.2.1 |
pvcDSlotThe destination slot for the PVC.rw INTEGER .1.3.6.1.4.1.251.1.1.17.2.1.1 |
pvcDLinkThe destination link for the PVC.rw INTEGER .1.3.6.1.4.1.251.1.1.17.2.1.2 |
pvcDvciThe destination virtual circuit identifier for the PVC.rw VirtualCircuitIdentifier .1.3.6.1.4.1.251.1.1.17.2.1.3 |
pvcDvpiThe destination virtual path identifier for the PVC.rw VirtualPathIdentifier .1.3.6.1.4.1.251.1.1.17.2.1.4 |
pvcSSlotThe source slot for the PVC.rw INTEGER .1.3.6.1.4.1.251.1.1.17.2.1.5 |
pvcSLinkThe source link for the PVC.rw INTEGER .1.3.6.1.4.1.251.1.1.17.2.1.6 |
pvcSvciThe source virtual circuit identifier for the PVC.rw VirtualCircuitIdentifier .1.3.6.1.4.1.251.1.1.17.2.1.7 |
pvcSvpiThe source virtual path identifier for the PVC.rw VirtualPathIdentifier .1.3.6.1.4.1.251.1.1.17.2.1.8 |
pvcForwardPeakCellRateForward Peak Cell Rate (CPS)rw INTEGER .1.3.6.1.4.1.251.1.1.17.2.1.9 |
pvcForwardPeakSizeForward Peak Bucket Size (Cells)rw INTEGER .1.3.6.1.4.1.251.1.1.17.2.1.10 |
pvcForwardPeakModeForward Peak Moderw Enumeration .1.3.6.1.4.1.251.1.1.17.2.1.11 |
pvcBackwardPeakCellRateBackward Peak Cell Rate (CPS)rw INTEGER .1.3.6.1.4.1.251.1.1.17.2.1.12 |
pvcBackwardPeakSizeBackward Peak Bucket Size (Cells)rw INTEGER .1.3.6.1.4.1.251.1.1.17.2.1.13 |
pvcBackwardPeakModeBackward Peak Moderw Enumeration .1.3.6.1.4.1.251.1.1.17.2.1.14 |
pvcForwardSustainedCellRateForward Sustained Cell Rate (CPS)rw INTEGER .1.3.6.1.4.1.251.1.1.17.2.1.15 |
pvcForwardSustainedSizeForward Sustained Bucket Size (Cells)rw INTEGER .1.3.6.1.4.1.251.1.1.17.2.1.16 |
pvcForwardSustainedModeForward Sustained Moderw Enumeration .1.3.6.1.4.1.251.1.1.17.2.1.17 |
pvcBackwardSustainedCellRateBackward Sustained Cell Rate (CPS)rw INTEGER .1.3.6.1.4.1.251.1.1.17.2.1.18 |
pvcBackwardSustainedSizeBackward Sustained Bucket Size (Cells)rw INTEGER .1.3.6.1.4.1.251.1.1.17.2.1.19 |
pvcBackwardSustainedModeBackward Sustained Moderw Enumeration .1.3.6.1.4.1.251.1.1.17.2.1.20 |
pvcAuxForwardPeakCellRateAuxiliary Forward Peak Cell Rate (CPS)rw INTEGER .1.3.6.1.4.1.251.1.1.17.2.1.21 |
pvcAuxForwardPeakSizeAuxiliary Forward Peak Bucket Size (Cells)rw INTEGER .1.3.6.1.4.1.251.1.1.17.2.1.22 |
pvcAuxForwardPeakModeAuxiliary Forward Peak Moderw Enumeration .1.3.6.1.4.1.251.1.1.17.2.1.23 |
pvcAuxBackwardPeakCellRateAuxiliary Backward Peak Cell Rate (CPS)rw INTEGER .1.3.6.1.4.1.251.1.1.17.2.1.24 |
pvcAuxBackwardPeakSizeAuxiliary Backward Peak Bucket Size (Cells)rw INTEGER .1.3.6.1.4.1.251.1.1.17.2.1.25 |
pvcAuxBackwardPeakModeAuxiliary Backward Peak Moderw Enumeration .1.3.6.1.4.1.251.1.1.17.2.1.26 |
pvcAuxForwardSustainedCellRateAuxiliary Forward Sustained Cell Rate (CPS)rw INTEGER .1.3.6.1.4.1.251.1.1.17.2.1.27 |
pvcAuxForwardSustainedSizeAuxiliary Forward Sustained Bucket Size (Cells)rw INTEGER .1.3.6.1.4.1.251.1.1.17.2.1.28 |
pvcAuxForwardSustainedModeAuxiliary Forward Sustained Moderw Enumeration .1.3.6.1.4.1.251.1.1.17.2.1.29 |
pvcAuxBackwardSustainedCellRateAuxiliary Backward Sustained Cell Rate (CPS)rw INTEGER .1.3.6.1.4.1.251.1.1.17.2.1.30 |
pvcAuxBackwardSustainedSizeAuxiliary Backward Sustained Bucket Sizerw INTEGER .1.3.6.1.4.1.251.1.1.17.2.1.31 |
pvcAuxBackwardSustainedModeAuxiliary Backward Sustained Moderw Enumeration .1.3.6.1.4.1.251.1.1.17.2.1.32 |
pvcQoSClassCBR(1) is a constant bit rate service, vbr-high(2) is variable bit rate with high priority, vbr-med(3) has low priority, vbr-low(4) is a `best effort' service - low priority and the cells may be discard.rw Enumeration .1.3.6.1.4.1.251.1.1.17.2.1.33 |
pvcStatusIf this object is set to invalid(2), the PVC entry is removed. Set to start-PVC(3) to activate the PVC. When the state changes to running(5) then the PVC is successfully running. (6) pvc restartedrw Enumeration .1.3.6.1.4.1.251.1.1.17.2.1.34 |
pvcMulticastIf this object is set to no, multicast is not allowed; otherwise, multicast is allowed.rw Enumeration .1.3.6.1.4.1.251.1.1.17.2.1.35 |
pvcInternalVpiThis object indicates the internal VPI value that the source side of multicast tree ranslates its orignal VPI to.ro INTEGER .1.3.6.1.4.1.251.1.1.17.2.1.36 |
pvcInternalVciThis object indicates the internal VCI value that the source side of multicast tree ranslates its orignal VCI to.ro INTEGER .1.3.6.1.4.1.251.1.1.17.2.1.37 |
pvcNumLeavesThis object indicates the number of leaves this multicast tree currently contains.ro INTEGER .1.3.6.1.4.1.251.1.1.17.2.1.38 |
pvcDirectionThis object determines if a multicast PVC is to be unidirectional or bidirectionalrw Enumeration .1.3.6.1.4.1.251.1.1.17.2.1.39 |
dv2Svc OBJECT IDENTIFIER .1.3.6.1.4.1.251.1.1.18 |
svcMaxPtPtConnectionsThe maximum number of point-to-point connections.rw INTEGER .1.3.6.1.4.1.251.1.1.18.1 |
svcMaxPtMptConnectionsThe maximum number of point-to-multipoint connections.rw INTEGER .1.3.6.1.4.1.251.1.1.18.2 |
svcMaxPtMptPartiesThe maximum number of parties in a point-to-multipoint connection.rw INTEGER .1.3.6.1.4.1.251.1.1.18.3 |
svcResourceTableThis table contains information about the resource available for svcs on each link. SEQUENCE OF SvcResourceEntry .1.3.6.1.4.1.251.1.1.18.6 |
svcResourceEntry SvcResourceEntry .1.3.6.1.4.1.251.1.1.18.6.1 |
svcSAPIdentifies the SAP.ro INTEGER .1.3.6.1.4.1.251.1.1.18.6.1.1 |
svcHiLoSelect VPI/VCI values from low to high or high to lowrw Enumeration .1.3.6.1.4.1.251.1.1.18.6.1.2 |
svcVciStartIdentifies the start of the range of SVC VCI values supported on this link.ro INTEGER .1.3.6.1.4.1.251.1.1.18.6.1.3 |
svcVciEndIdentifies the end of the range of SVC VCI values supported on this link.ro INTEGER .1.3.6.1.4.1.251.1.1.18.6.1.4 |
svcVpiStartIdentifies the start of the range of SVC VPI values supported on this link.rw INTEGER .1.3.6.1.4.1.251.1.1.18.6.1.5 |
svcVpiEndIdentifies the end of the range of SVC VPI values supported on this link.rw INTEGER .1.3.6.1.4.1.251.1.1.18.6.1.6 |
svcVpStartIdentifies the start of the range of SVPs supported on this link.rw INTEGER .1.3.6.1.4.1.251.1.1.18.6.1.7 |
svcVpEndIdentifies the end of the range of SVPs supported on this link.rw INTEGER .1.3.6.1.4.1.251.1.1.18.6.1.8 |
svcBackwardCellRateTotalThe backward total cell rate configured for SVCs on this link. Note that this object is in cells per second (CPS).rw INTEGER .1.3.6.1.4.1.251.1.1.18.6.1.11 |
svcBackwardCellRateAvailableThe backward cell rate available for SVCs on this link. Note that this object is in cells per second (CPS).ro INTEGER .1.3.6.1.4.1.251.1.1.18.6.1.12 |
svcSigVciThe VCI used for signalling.rw INTEGER .1.3.6.1.4.1.251.1.1.18.6.1.13 |
svcSigVpiThe VPI used for signalling.rw INTEGER .1.3.6.1.4.1.251.1.1.18.6.1.14 |
svcSAPStatusSelect on(4) to activate the SAP, off(1) to deactivate, reconfigure(2) to hot reconfigure the vci/vpi ranges and reset(3) to clear all calls on the SAP.rw Enumeration .1.3.6.1.4.1.251.1.1.18.6.1.15 |
svcCDVTSizeCell Delay Variation Tolerance size.rw INTEGER .1.3.6.1.4.1.251.1.1.18.6.1.16 |
svcIntTypeInterface type - NETWORK or USER.rw Enumeration .1.3.6.1.4.1.251.1.1.18.6.1.17 |
svcPolicingPolicing - ON or OFFrw Enumeration .1.3.6.1.4.1.251.1.1.18.6.1.18 |
svcLowPriOverbookFactorThis is the percentage of low priority traffic overbook factor.rw INTEGER .1.3.6.1.4.1.251.1.1.18.6.1.19 |
svcMaxSapConnMaximum SVCs this SAPrw INTEGER .1.3.6.1.4.1.251.1.1.18.6.1.20 |
svcCurSapConnCurrent SVC count this SAPro INTEGER .1.3.6.1.4.1.251.1.1.18.6.1.21 |
svcLinkNoThis is the physical link number associated with this SAPrw INTEGER .1.3.6.1.4.1.251.1.1.18.6.1.22 |
svcVpiMappingVPI and VPCI mapping statusrw Enumeration .1.3.6.1.4.1.251.1.1.18.6.1.23 |
svcQosRouteQoS based routerw Enumeration .1.3.6.1.4.1.251.1.1.18.6.1.24 |
svcSwtchUNI Interface Typerw Enumeration .1.3.6.1.4.1.251.1.1.18.6.1.25 |
svcRestartSend Restart when link is uprw Enumeration .1.3.6.1.4.1.251.1.1.18.6.1.26 |
svcE164AddrThe E.164 address for this SAPrw E164 .1.3.6.1.4.1.251.1.1.18.6.1.27 |
svcAutoSapOffThis option allows a Sap Status to be automatically turned OFF after T309 expiry. Select Yes(1) if a sap (which was ON before) is to be turned OFF after T309 expiry, else select No(2). By default, No(2) is selected.rw Enumeration .1.3.6.1.4.1.251.1.1.18.6.1.28 |
svcTableThis table contains information on each on SVC. SEQUENCE OF SvcEntry .1.3.6.1.4.1.251.1.1.18.7 |
svcEntry SvcEntry .1.3.6.1.4.1.251.1.1.18.7.1 |
svcIdThe svc ID numberro INTEGER .1.3.6.1.4.1.251.1.1.18.7.1.1 |
svcDSlotThe destination slot of the SVC.ro INTEGER .1.3.6.1.4.1.251.1.1.18.7.1.2 |
svcDLinkThe destination link of the SVC.ro INTEGER .1.3.6.1.4.1.251.1.1.18.7.1.3 |
svcDvciThe destination virtual circuit identifier for the SVC.ro VirtualCircuitIdentifier .1.3.6.1.4.1.251.1.1.18.7.1.4 |
svcDvpiThe destination virtual path identifier for the SVC.ro VirtualPathIdentifier .1.3.6.1.4.1.251.1.1.18.7.1.5 |
svcDE164The destination E.164 address for the SVC.ro E164 .1.3.6.1.4.1.251.1.1.18.7.1.6 |
svcDE164SubThe destination sub-address for the SVC.ro E164SUB .1.3.6.1.4.1.251.1.1.18.7.1.7 |
svcSSlotThe source slot of the SVC.ro INTEGER .1.3.6.1.4.1.251.1.1.18.7.1.8 |
svcSLinkThe source link of the SVC.ro INTEGER .1.3.6.1.4.1.251.1.1.18.7.1.9 |
svcSvciThe source virtual circuit identifier for a SVC.ro VirtualCircuitIdentifier .1.3.6.1.4.1.251.1.1.18.7.1.10 |
svcSvpiThe source virtual path identifier for a SVC.ro VirtualPathIdentifier .1.3.6.1.4.1.251.1.1.18.7.1.11 |
svcSE164The source E.164 address for the SVC.ro E164 .1.3.6.1.4.1.251.1.1.18.7.1.12 |
svcSE164SubThe source sub-address for the SVC.ro E164SUB .1.3.6.1.4.1.251.1.1.18.7.1.13 |
svcForwardPeakCellRateThe forward user cell rate for a SVC. The forward user cell rate is a measurement of bandwidth available to the initiating user to transfer information to the responding user.ro INTEGER .1.3.6.1.4.1.251.1.1.18.7.1.14 |
svcForwardPeakModeSVC/SVP Forward Peak Modero Enumeration .1.3.6.1.4.1.251.1.1.18.7.1.15 |
svcBackwardPeakCellRateThe backward user cell rate for a SVC. The backward user cell rate is a measurement of bandwidth available to the responding user to transfer information to the initiating user.ro INTEGER .1.3.6.1.4.1.251.1.1.18.7.1.16 |
svcBackwardPeakModeSVC/SVP Backward Peak Modero Enumeration .1.3.6.1.4.1.251.1.1.18.7.1.17 |
svcForwardSustainableCellRateThe sustainable forward cell rate for the SVC.ro INTEGER .1.3.6.1.4.1.251.1.1.18.7.1.18 |
svcForwardMaxBurstSizeThe forward maximum burst size for the SVC.ro INTEGER .1.3.6.1.4.1.251.1.1.18.7.1.19 |
svcForwardSustainableModeSVC/SVP Forward Sustained Modero Enumeration .1.3.6.1.4.1.251.1.1.18.7.1.20 |
svcBackwardSustainableCellRateThe sustainable backward cell rate for the SVC.ro INTEGER .1.3.6.1.4.1.251.1.1.18.7.1.21 |
svcBackwardMaxBurstSizeThe backward maximum burst size for the SVC.ro INTEGER .1.3.6.1.4.1.251.1.1.18.7.1.22 |
svcBackwardSustainableModeSVC/SVP Backward Sustained Modero Enumeration .1.3.6.1.4.1.251.1.1.18.7.1.23 |
svcQoSClassCBR(1) is a constant bit rate service, vbr-high(2) is variable bit rate with high priority, vbr-med(3) has low priority, vbr-low(4) is a `best effort' service - low priority and the cells may be discarded.ro Enumeration .1.3.6.1.4.1.251.1.1.18.7.1.24 |
svcBillTagThis identifies the billable SVC.ro INTEGER .1.3.6.1.4.1.251.1.1.18.7.1.25 |
svcDurationDuration of the SVC in milliseconds.ro Counter .1.3.6.1.4.1.251.1.1.18.7.1.26 |
svcTypeThe type of SVC.ro Enumeration .1.3.6.1.4.1.251.1.1.18.7.1.27 |
svcStatusIf this object is set to invalid (2), the SVC is cleared and the entry is removed. If set to active(4) then the SVC is active.rw Enumeration .1.3.6.1.4.1.251.1.1.18.7.1.28 |
svcNumLeavesNumber of multicast leavesro INTEGER .1.3.6.1.4.1.251.1.1.18.7.1.29 |
svcInternalVpiinternal VPI used for multicast operationro INTEGER .1.3.6.1.4.1.251.1.1.18.7.1.30 |
svcInternalVciinternal VCI used for multicast operationro INTEGER .1.3.6.1.4.1.251.1.1.18.7.1.31 |
sPvcTableThis table contains information on Semi-Permanent Virtual Circuits (SPVCs). SEQUENCE OF SPvcEntry .1.3.6.1.4.1.251.1.1.18.8 |
sPvcEntry SPvcEntry .1.3.6.1.4.1.251.1.1.18.8.1 |
sPvcIdSlot-unique SPVC identifier.rw INTEGER .1.3.6.1.4.1.251.1.1.18.8.1.1 |
sPvcCallIdCall identifier.ro INTEGER .1.3.6.1.4.1.251.1.1.18.8.1.2 |
sPvcLinkThe physical link for the SPVC.rw INTEGER .1.3.6.1.4.1.251.1.1.18.8.1.3 |
sPvcAddressThe E.164 address for the SPVC.rw E164 .1.3.6.1.4.1.251.1.1.18.8.1.4 |
sPvcForwardPeakCellRateThe forward user cell rate for an SPVC. The forward user cell rate is a measurement of bandwidth available to the initiating user to transfer information to the responding user.rw INTEGER .1.3.6.1.4.1.251.1.1.18.8.1.5 |
sPvcForwardPeakModeSPVC/SPVP Forward Peak Moderw Enumeration .1.3.6.1.4.1.251.1.1.18.8.1.6 |
sPvcBackwardPeakCellRateThe backward user cell rate for an SPVC. The backward user cell rate is a measurement of bandwidth available to the responding user to transfer information to the initiating user.rw INTEGER .1.3.6.1.4.1.251.1.1.18.8.1.7 |
sPvcBackwardPeakModeSPVC/SPVP Backward Peak Moderw Enumeration .1.3.6.1.4.1.251.1.1.18.8.1.8 |
sPvcForwardSustainableCellRateThe sustainable forward cell rate for the SPVC.rw INTEGER .1.3.6.1.4.1.251.1.1.18.8.1.9 |
sPvcForwardMaxBurstSizeThe forward maximum burst size for the SPVC.rw INTEGER .1.3.6.1.4.1.251.1.1.18.8.1.10 |
sPvcForwardSustainableModeSPVC/SPVP Forward Sustained Moderw Enumeration .1.3.6.1.4.1.251.1.1.18.8.1.11 |
sPvcBackwardSustainableCellRateThe sustainable backward cell rate for the SPVC.rw INTEGER .1.3.6.1.4.1.251.1.1.18.8.1.12 |
sPvcBackwardMaxBurstSizeThe backward maximum burst size for the SPVC.rw INTEGER .1.3.6.1.4.1.251.1.1.18.8.1.13 |
sPvcBackwardSustainableModeSPVC/SPVP Backward Sustained Moderw Enumeration .1.3.6.1.4.1.251.1.1.18.8.1.14 |
sPvcQoSClassCBR(1) is a constant bit rate service, vbr-high(2) is variable bit rate with high priority, vbr-med(3) has low priority, vbr-low(4) has low priority and the cells may be discarded, best-effort is the same as vbr-low except no bandwidth is reserved.rw Enumeration .1.3.6.1.4.1.251.1.1.18.8.1.15 |
sPvcSourceVciThe source virtual circuit identifier for the SPVC.rw VirtualCircuitIdentifier .1.3.6.1.4.1.251.1.1.18.8.1.16 |
sPvcSourceVpiThe source virtual path identifier for the SPVC.rw VirtualPathIdentifier .1.3.6.1.4.1.251.1.1.18.8.1.17 |
sPvcTargetVciThe target virtual circuit identifier for the SPVC.rw VirtualCircuitIdentifier .1.3.6.1.4.1.251.1.1.18.8.1.18 |
sPvcTargetVpiThe target virtual path identifier for the SPVC.rw VirtualPathIdentifier .1.3.6.1.4.1.251.1.1.18.8.1.19 |
sPvcRetryRetry timeout. Zero represents an infinite timeout.rw INTEGER .1.3.6.1.4.1.251.1.1.18.8.1.20 |
sPvcConnectTimeConnect time in ms.ro INTEGER .1.3.6.1.4.1.251.1.1.18.8.1.21 |
sPvcNumberRetriesNumber of retries to attempt. Zero represents no limit.rw INTEGER .1.3.6.1.4.1.251.1.1.18.8.1.22 |
sPvcFailuresA count of the SPVC setup failures.ro INTEGER .1.3.6.1.4.1.251.1.1.18.8.1.23 |
sPvcAlertFailuresDescribes the circumstances under which to issue an Alert message to the NMS.rw Enumeration .1.3.6.1.4.1.251.1.1.18.8.1.24 |
sPvcCauseDiagCause and diagnostic codes.ro Q93bCauseDiag .1.3.6.1.4.1.251.1.1.18.8.1.25 |
sPvcTypeIf the SPVC entry is passive, it will not try to initiate a call. An active
will attempt to build an SPVC at intervals set by the retry field.ro Enumeration .1.3.6.1.4.1.251.1.1.18.8.1.26 |
sPvcCallStateSets the state of the SPVC. Set the value to invalid(3) to tear down the SPVC.rw Enumeration .1.3.6.1.4.1.251.1.1.18.8.1.27 |
sPvcStatusDescribes the state of the SPVC.ro Enumeration .1.3.6.1.4.1.251.1.1.18.8.1.28 |
sPvcCauseDiagCodeCause and diagnostic codes as defined in UNI-3.0 Annex E .ro INTEGER .1.3.6.1.4.1.251.1.1.18.8.1.29 |
sPvcMulticastpt-pt - point-to-point SPVC; pt-mpt - point-to-multipoint SPVC; bidirect-root: pt-mpt birection root.rw Enumeration .1.3.6.1.4.1.251.1.1.18.8.1.30 |
svcQ93bStatTableThis table contains statistical protocol information for each link. SEQUENCE OF SvcQ93bStatEntry .1.3.6.1.4.1.251.1.1.18.9 |
svcQ93bStatEntry SvcQ93bStatEntry .1.3.6.1.4.1.251.1.1.18.9.1 |
svcQ93bStatSAPThis is the layer 3 Service Access Point for the link.ro INTEGER .1.3.6.1.4.1.251.1.1.18.9.1.1 |
svcQ93bStatActiveNumber of calls currently active on this SAP.ro INTEGER .1.3.6.1.4.1.251.1.1.18.9.1.2 |
svcQ93bStatAccumalativeTotal number of calls established on this SAP.ro INTEGER .1.3.6.1.4.1.251.1.1.18.9.1.3 |
svcQ93bStatCallProcTxCall Proceeding pdus transmitted on this SAP.ro INTEGER .1.3.6.1.4.1.251.1.1.18.9.1.4 |
svcQ93bStatConnTxConnect pdus transmitted on this SAP.ro INTEGER .1.3.6.1.4.1.251.1.1.18.9.1.5 |
svcQ93bStatConnAckTxConnect Acknowledge pdus transmitted on this SAP.ro INTEGER .1.3.6.1.4.1.251.1.1.18.9.1.6 |
svcQ93bStatSetupTxSetup pdus transmitted on this SAP.ro INTEGER .1.3.6.1.4.1.251.1.1.18.9.1.7 |
svcQ93bStatRelTxRelease pdus transmitted on this SAP.ro INTEGER .1.3.6.1.4.1.251.1.1.18.9.1.8 |
svcQ93bStatRelCmpltTxRelease Complete pdus transmitted on this SAP.ro INTEGER .1.3.6.1.4.1.251.1.1.18.9.1.9 |
svcQ93bStatRstTxRestart pdus transmitted on this SAP.ro INTEGER .1.3.6.1.4.1.251.1.1.18.9.1.10 |
svcQ93bStatRstAckTxRestart Acknowledge pdus transmitted on this SAP.ro INTEGER .1.3.6.1.4.1.251.1.1.18.9.1.11 |
svcQ93bStatStatTxStatus pdus transmitted on this SAP.ro INTEGER .1.3.6.1.4.1.251.1.1.18.9.1.12 |
svcQ93bStatStatEnqTxStatus Enquiry pdus transmitted on this SAP.ro INTEGER .1.3.6.1.4.1.251.1.1.18.9.1.13 |
svcQ93bStatAddPtyTxAdd Party pdus transmitted on this SAP.ro INTEGER .1.3.6.1.4.1.251.1.1.18.9.1.14 |
svcQ93bStatAddPtyAckTxAdd Party Acknowledge pdus transmitted on this SAP.ro INTEGER .1.3.6.1.4.1.251.1.1.18.9.1.15 |
svcQ93bStatAddPtyRejTxAdd Party Reject pdus transmitted on this SAP.ro INTEGER .1.3.6.1.4.1.251.1.1.18.9.1.16 |
svcQ93bStatDropPtyTxDrop Party pdus transmitted on this SAP.ro INTEGER .1.3.6.1.4.1.251.1.1.18.9.1.17 |
svcQ93bStatDropPtyAckTxDrop Party Acknowledge pdus transmitted on this SAP.ro INTEGER .1.3.6.1.4.1.251.1.1.18.9.1.18 |
svcQ93bStatLstCauseTxLast cause code transmitted.ro INTEGER .1.3.6.1.4.1.251.1.1.18.9.1.19 |
svcQ93bStatLstDiagTxLast diagnostic code transmitted.ro INTEGER .1.3.6.1.4.1.251.1.1.18.9.1.20 |
svcQ93bStatCallProcRxCall Proceeding pdus received on this SAP.ro INTEGER .1.3.6.1.4.1.251.1.1.18.9.1.21 |
svcQ93bStatConnRxConnect pdus received on this SAP.ro INTEGER .1.3.6.1.4.1.251.1.1.18.9.1.22 |
svcQ93bStatConnAckRxConnect Acknowledge pdus received on this SAP.ro INTEGER .1.3.6.1.4.1.251.1.1.18.9.1.23 |
svcQ93bStatSetupRxSetup pdus received on this SAP.ro INTEGER .1.3.6.1.4.1.251.1.1.18.9.1.24 |
svcQ93bStatRelRxRelease pdus received on this SAP.ro INTEGER .1.3.6.1.4.1.251.1.1.18.9.1.25 |
svcQ93bStatRelCmpltRxRelease Complete pdus received on this SAP.ro INTEGER .1.3.6.1.4.1.251.1.1.18.9.1.26 |
svcQ93bStatRstRxRestart pdus received on this SAP.ro INTEGER .1.3.6.1.4.1.251.1.1.18.9.1.27 |
svcQ93bStatRstAckRxRestart Acknowledge pdus received on this SAP.ro INTEGER .1.3.6.1.4.1.251.1.1.18.9.1.28 |
svcQ93bStatStatRxStatus pdus received on this SAP.ro INTEGER .1.3.6.1.4.1.251.1.1.18.9.1.29 |
svcQ93bStatStatEnqRxStatus Enquiry pdus received on this SAP.ro INTEGER .1.3.6.1.4.1.251.1.1.18.9.1.30 |
svcQ93bStatAddPtyRxAdd Party pdus received on this SAP.ro INTEGER .1.3.6.1.4.1.251.1.1.18.9.1.31 |
svcQ93bStatAddPtyAckRxAdd Party Acknowledge pdus received on this SAP.ro INTEGER .1.3.6.1.4.1.251.1.1.18.9.1.32 |
svcQ93bStatAddPtyRejRxAdd Party Reject pdus received on this SAP.ro INTEGER .1.3.6.1.4.1.251.1.1.18.9.1.33 |
svcQ93bStatDropPtyRxDrop Party pdus received on this SAP.ro INTEGER .1.3.6.1.4.1.251.1.1.18.9.1.34 |
svcQ93bStatDropPtyAckRxDrop Party Acknowledge pdus received on this SAP.ro INTEGER .1.3.6.1.4.1.251.1.1.18.9.1.35 |
svcQ93bStatLstCauseRxLast cause code received.ro INTEGER .1.3.6.1.4.1.251.1.1.18.9.1.36 |
svcQ93bStatLstDiagRxLast diagnostic code received.ro INTEGER .1.3.6.1.4.1.251.1.1.18.9.1.37 |
svcQ93bStatClrClear Q.93B statistics for this SAP.rw Enumeration .1.3.6.1.4.1.251.1.1.18.9.1.38 |
svcQ93bStatDiagTxTx SAP diagnostic codesro Q93bCauseDiag .1.3.6.1.4.1.251.1.1.18.9.1.39 |
svcQ93bStatDiagRxRx SAP diagnostic codesro Q93bCauseDiag .1.3.6.1.4.1.251.1.1.18.9.1.40 |
svcQsaalStatTableThis table contains protocol information for the Q.SAAL layer for each link. SEQUENCE OF SvcQsaalStatEntry .1.3.6.1.4.1.251.1.1.18.10 |
svcQsaalStatEntry SvcQsaalStatEntry .1.3.6.1.4.1.251.1.1.18.10.1 |
svcQsaalStatSAPThis is the layer 3 Service Access Point for the link.ro INTEGER .1.3.6.1.4.1.251.1.1.18.10.1.1 |
svcQsaalStatOutSduDiscOutgoing SDUs discarded.ro INTEGER .1.3.6.1.4.1.251.1.1.18.10.1.2 |
svcQsaalStatInPduErrNumber of incoming PDUs with a reception error.ro INTEGER .1.3.6.1.4.1.251.1.1.18.10.1.3 |
svcQsaalStatInPduDiscNumber of incoming PDUs discarded.ro INTEGER .1.3.6.1.4.1.251.1.1.18.10.1.4 |
svcQsaalStatOutPduErrNumber of outgoing PDUs with a transmission error.ro INTEGER .1.3.6.1.4.1.251.1.1.18.10.1.5 |
svcQsaalStatOutPduDiscNumber of outgoing PDUs discarded.ro INTEGER .1.3.6.1.4.1.251.1.1.18.10.1.6 |
svcQsaalStatBgnTxBGN pdus transmitted on this SAP.ro INTEGER .1.3.6.1.4.1.251.1.1.18.10.1.7 |
svcQsaalStatBgakTxBGAK pdus transmitted on this SAP.ro INTEGER .1.3.6.1.4.1.251.1.1.18.10.1.8 |
svcQsaalStatBgrejTxBGREJ pdus transmitted on this SAP.ro INTEGER .1.3.6.1.4.1.251.1.1.18.10.1.9 |
svcQsaalStatEndTxEND pdus transmitted on this SAP.ro INTEGER .1.3.6.1.4.1.251.1.1.18.10.1.10 |
svcQsaalStatRsTxRS pdus transmitted on this SAP.ro INTEGER .1.3.6.1.4.1.251.1.1.18.10.1.11 |
svcQsaalStatRsakTxRSAK pdus transmitted on this SAP.ro INTEGER .1.3.6.1.4.1.251.1.1.18.10.1.12 |
svcQsaalStatSdTxSD pdus transmitted on this SAP.ro INTEGER .1.3.6.1.4.1.251.1.1.18.10.1.13 |
svcQsaalStatSdpTxSDP pdus transmitted on this SAP.ro INTEGER .1.3.6.1.4.1.251.1.1.18.10.1.14 |
svcQsaalStatPollTxPOLL pdus transmitted on this SAP.ro INTEGER .1.3.6.1.4.1.251.1.1.18.10.1.15 |
svcQsaalStatStatTxSTAT pdus transmitted on this SAP.ro INTEGER .1.3.6.1.4.1.251.1.1.18.10.1.16 |
svcQsaalStatUstatTxUSTAT pdus transmitted on this SAP.ro INTEGER .1.3.6.1.4.1.251.1.1.18.10.1.17 |
svcQsaalStatUdTxUD pdus transmitted on this SAP.ro INTEGER .1.3.6.1.4.1.251.1.1.18.10.1.18 |
svcQsaalStatMdTxMD pdus transmitted on this SAP.ro INTEGER .1.3.6.1.4.1.251.1.1.18.10.1.19 |
svcQsaalStatBgnRxBGN pdus received on this SAP.ro INTEGER .1.3.6.1.4.1.251.1.1.18.10.1.20 |
svcQsaalStatBgakRxBGAK pdus received on this SAP.ro INTEGER .1.3.6.1.4.1.251.1.1.18.10.1.21 |
svcQsaalStatBgrejRxBGREJ pdus received on this SAP.ro INTEGER .1.3.6.1.4.1.251.1.1.18.10.1.22 |
svcQsaalStatEndRxEND pdus received on this SAP.ro INTEGER .1.3.6.1.4.1.251.1.1.18.10.1.23 |
svcQsaalStatRsRxRS pdus received on this SAP.ro INTEGER .1.3.6.1.4.1.251.1.1.18.10.1.24 |
svcQsaalStatRsakRxRSAK pdus received on this SAP.ro INTEGER .1.3.6.1.4.1.251.1.1.18.10.1.25 |
svcQsaalStatSdRxSD pdus received on this SAP.ro INTEGER .1.3.6.1.4.1.251.1.1.18.10.1.26 |
svcQsaalStatSdpRxSDP pdus received on this SAP.ro INTEGER .1.3.6.1.4.1.251.1.1.18.10.1.27 |
svcQsaalStatPollRxPOLL pdus received on this SAP.ro INTEGER .1.3.6.1.4.1.251.1.1.18.10.1.28 |
svcQsaalStatStatRxSTAT pdus received on this SAP.ro INTEGER .1.3.6.1.4.1.251.1.1.18.10.1.29 |
svcQsaalStatUstatRxUSTAT pdus received on this SAP.ro INTEGER .1.3.6.1.4.1.251.1.1.18.10.1.30 |
svcQsaalStatUdRxUD pdus received on this SAP.ro INTEGER .1.3.6.1.4.1.251.1.1.18.10.1.31 |
svcQsaalStatMdRxMD pdus received on this SAP.ro INTEGER .1.3.6.1.4.1.251.1.1.18.10.1.32 |
svcQsaalStatClrClear statistics for this SAP.rw Enumeration .1.3.6.1.4.1.251.1.1.18.10.1.33 |
svcQsaalTmrPollSSCOP Timer_POLL (8=800ms).rw INTEGER .1.3.6.1.4.1.251.1.1.18.11 |
svcQsaalTmrKeepAliveSSCOP Timer_KEEPALIVE (20=2seconds).rw INTEGER .1.3.6.1.4.1.251.1.1.18.12 |
svcQsaalTmrNoResponseSSCOP Timer_NORESPONSE (100=10seconds).rw INTEGER .1.3.6.1.4.1.251.1.1.18.13 |
svcQsaalTmrCCSSCOP Timer_CC (20=2seconds).rw INTEGER .1.3.6.1.4.1.251.1.1.18.14 |
svcQsaalMaxPDSSCOP Maximum PD.rw INTEGER .1.3.6.1.4.1.251.1.1.18.15 |
svcQ93bTmrT303Q.93B T303 (40=4seconds).rw INTEGER .1.3.6.1.4.1.251.1.1.18.16 |
svcQ93bTmrT310Q.93B T310 (200=20seconds).rw INTEGER .1.3.6.1.4.1.251.1.1.18.17 |
svcQ93bTmrT308Q.93B T308 (300=30seconds).rw INTEGER .1.3.6.1.4.1.251.1.1.18.18 |
svcQ93bTmrT309Q.93B T309 (150=15seconds).rw INTEGER .1.3.6.1.4.1.251.1.1.18.19 |
maxOutstandingMax Outgoing Outstanding Calls.rw INTEGER .1.3.6.1.4.1.251.1.1.18.20 |
svcLoadRoutePoke point for loading routing tablesrw Enumeration .1.3.6.1.4.1.251.1.1.18.21 |
svcHalfConTimerSVC half connect recovery poll timerrw INTEGER .1.3.6.1.4.1.251.1.1.18.22 |
svcHalfConCntSVC half connect counterro INTEGER .1.3.6.1.4.1.251.1.1.18.23 |
svcQ93bTmrT398Q.93B T398 (40= 4 seconds).rw INTEGER .1.3.6.1.4.1.251.1.1.18.24 |
svcQ93bTmrT399Q.93B T399 (140= 14 seconds).rw INTEGER .1.3.6.1.4.1.251.1.1.18.25 |
svcRetryPeriodRetry Periodrw INTEGER .1.3.6.1.4.1.251.1.1.18.26 |
svcCellRateTableThis table contains information about the limitations on Cell Rates on link SEQUENCE OF SvcCellRateEntry .1.3.6.1.4.1.251.1.1.18.27 |
svcCellRateEntry SvcCellRateEntry .1.3.6.1.4.1.251.1.1.18.27.1 |
svcCRLinkNoThis is the physical link number associated with this SAPro INTEGER .1.3.6.1.4.1.251.1.1.18.27.1.1 |
svcPCRCLP01MaxPCRCLP01 Max(0 disables checking)rw INTEGER .1.3.6.1.4.1.251.1.1.18.27.1.2 |
svcSCRMaxSCR Max(0 disables checking)rw INTEGER .1.3.6.1.4.1.251.1.1.18.27.1.3 |
svcMBSMaxMBS Max(0 disables checking)rw INTEGER .1.3.6.1.4.1.251.1.1.18.27.1.4 |
svcTrafficTableThis table contains information about the limitations on Cell Rates on link SEQUENCE OF SvcTrafficEntry .1.3.6.1.4.1.251.1.1.18.28 |
svcTrafficEntry SvcTrafficEntry .1.3.6.1.4.1.251.1.1.18.28.1 |
svcTLinkNoLnk Numberro INTEGER .1.3.6.1.4.1.251.1.1.18.28.1.1 |
svcCBRallowedAllows or disallows CBR trafficrw Enumeration .1.3.6.1.4.1.251.1.1.18.28.1.2 |
svcVBRHallowedAllows or disallows VBR High trafficrw Enumeration .1.3.6.1.4.1.251.1.1.18.28.1.3 |
svcVBRMallowedAllows or disallows VBR Med trafficrw Enumeration .1.3.6.1.4.1.251.1.1.18.28.1.4 |
svcVBRLUBRallowedAllows or disallows VBR Low/UBR trafficrw Enumeration .1.3.6.1.4.1.251.1.1.18.28.1.5 |
svcVBRLUBRsubtractpercentSpecifies a percentage of BW to be subtracted for VBR Low/UBR trafficrw INTEGER .1.3.6.1.4.1.251.1.1.18.28.1.6 |
dv2CE OBJECT IDENTIFIER .1.3.6.1.4.1.251.1.1.19 |
ceTableConfiguration Table for dv2CE Links SEQUENCE OF CeEntry .1.3.6.1.4.1.251.1.1.19.1 |
ceEntry CeEntry .1.3.6.1.4.1.251.1.1.19.1.1 |
ceLinkNoLink Number for Table Entryro INTEGER .1.3.6.1.4.1.251.1.1.19.1.1.1 |
ceEnableSetting to yes(1) enables the Linkrw Enumeration .1.3.6.1.4.1.251.1.1.19.1.1.2 |
ceModeService Clock Recovery Moderw Enumeration .1.3.6.1.4.1.251.1.1.19.1.1.3 |
cePrioritySet to high for normal CBR operationro Enumeration .1.3.6.1.4.1.251.1.1.19.1.1.4 |
cePvcValidIndicates if valid PVC exists for Linkro Enumeration .1.3.6.1.4.1.251.1.1.19.1.1.5 |
ceDstSlotDestination Slot for PVCro INTEGER .1.3.6.1.4.1.251.1.1.19.1.1.6 |
ceDstLinkDestination Link for PVCro Enumeration .1.3.6.1.4.1.251.1.1.19.1.1.7 |
ceDstVpiDestination VPI for PVCro VirtualPathIdentifier .1.3.6.1.4.1.251.1.1.19.1.1.8 |
ceDstVciDestination VCI for PVCro VirtualCircuitIdentifier .1.3.6.1.4.1.251.1.1.19.1.1.9 |
ceCDVCell Delay Variation Tolerancerw INTEGER .1.3.6.1.4.1.251.1.1.19.1.1.10 |
ceCDVMaxCell Delay Variation Tolerancerw INTEGER .1.3.6.1.4.1.251.1.1.19.1.1.11 |
ceMulticastIs link part of multicast treero Enumeration .1.3.6.1.4.1.251.1.1.19.1.1.24 |
ceXhIntXH Interface for Linkro Enumeration .1.3.6.1.4.1.251.1.1.19.1.1.25 |
ceStatTablestatus information about the dv2CE. SEQUENCE OF CeStatEntry .1.3.6.1.4.1.251.1.1.19.2 |
ceStatEntry CeStatEntry .1.3.6.1.4.1.251.1.1.19.2.1 |
ceStatPortNoLink Number for Table Entryro INTEGER .1.3.6.1.4.1.251.1.1.19.2.1.1 |
ceStatResetClear Statistics for Linkrw Enumeration .1.3.6.1.4.1.251.1.1.19.2.1.2 |
ceStatTxStateIndicates if data is being received and segmentedro Enumeration .1.3.6.1.4.1.251.1.1.19.2.1.3 |
ceStatRxStateIndicates if data being reassembled and transmittedro Enumeration .1.3.6.1.4.1.251.1.1.19.2.1.4 |
ceTxCntCount of Cells transmitted from switch fabricro Counter .1.3.6.1.4.1.251.1.1.19.2.1.5 |
ceRxCntCount of Cells received into switch fabricro Counter .1.3.6.1.4.1.251.1.1.19.2.1.6 |
ceOflCntCount of 1S intervals during which RX FIFO overflowedro Counter .1.3.6.1.4.1.251.1.1.19.2.1.7 |
ceUflCntCount of 1S intervals during which RX FIFO underflowedro Counter .1.3.6.1.4.1.251.1.1.19.2.1.8 |
ceDisCntCount of 1S intervals during which cells were discardedro Counter .1.3.6.1.4.1.251.1.1.19.2.1.9 |
ceInvCntCount of 1S intervals during which cells were inventedro Counter .1.3.6.1.4.1.251.1.1.19.2.1.10 |
ceResCntCount of 1S intervals during which AAL1 resync occurredro Counter .1.3.6.1.4.1.251.1.1.19.2.1.11 |
ceFifoLvlCntNumber of Cells currently in FIFOro Counter .1.3.6.1.4.1.251.1.1.19.2.1.12 |
cePriValPrimary Clock Validro Enumeration .1.3.6.1.4.1.251.1.1.19.21 |
ceSecValSecondary Clock Validro Enumeration .1.3.6.1.4.1.251.1.1.19.22 |
ceClkSelClock Selectro Enumeration .1.3.6.1.4.1.251.1.1.19.23 |
ceClkInpIs there clock inputro Enumeration .1.3.6.1.4.1.251.1.1.19.24 |
ceStr3Is there STR3ro Enumeration .1.3.6.1.4.1.251.1.1.19.25 |
dv2VE OBJECT IDENTIFIER .1.3.6.1.4.1.251.1.1.20 |
veTableConfiguration Table for dv2VE Links SEQUENCE OF VeEntry .1.3.6.1.4.1.251.1.1.20.1 |
veEntry VeEntry .1.3.6.1.4.1.251.1.1.20.1.1 |
veLinkNoLink Number for Table Entryro INTEGER .1.3.6.1.4.1.251.1.1.20.1.1.1 |
veEnableSetting to yes(1) enables the Linkrw Enumeration .1.3.6.1.4.1.251.1.1.20.1.1.2 |
veModeService Clock Recovery Modero Enumeration .1.3.6.1.4.1.251.1.1.20.1.1.3 |
vePrioritySet to high for normal CBR operationro Enumeration .1.3.6.1.4.1.251.1.1.20.1.1.4 |
vePvcValidIndicates if valid PVC exists for Linkro Enumeration .1.3.6.1.4.1.251.1.1.20.1.1.5 |
veDstSlotDestination Slot for PVCro INTEGER .1.3.6.1.4.1.251.1.1.20.1.1.6 |
veDstLinkDestination Link for PVCro Enumeration .1.3.6.1.4.1.251.1.1.20.1.1.7 |
veDstVpiDestination VPI for PVCro VirtualPathIdentifier .1.3.6.1.4.1.251.1.1.20.1.1.8 |
veDstVciDestination VCI for PVCro VirtualCircuitIdentifier .1.3.6.1.4.1.251.1.1.20.1.1.9 |
veCDVCell Delay Variation Tolerancerw INTEGER .1.3.6.1.4.1.251.1.1.20.1.1.10 |
veCDVMaxCell Delay Variation Tolerancerw INTEGER .1.3.6.1.4.1.251.1.1.20.1.1.11 |
veMulticastIs link part of multicast treero Enumeration .1.3.6.1.4.1.251.1.1.20.1.1.24 |
veXhIntXH Interface for Linkro Enumeration .1.3.6.1.4.1.251.1.1.20.1.1.25 |
veStatTablestatus information about the dv2VE. SEQUENCE OF VeStatEntry .1.3.6.1.4.1.251.1.1.20.2 |
veStatEntry VeStatEntry .1.3.6.1.4.1.251.1.1.20.2.1 |
veStatPortNoLink Number for Table Entryro INTEGER .1.3.6.1.4.1.251.1.1.20.2.1.1 |
veStatResetClear Statistics for Linkrw Enumeration .1.3.6.1.4.1.251.1.1.20.2.1.2 |
veStatTxStateIndicates if data is being received and segmentedro Enumeration .1.3.6.1.4.1.251.1.1.20.2.1.3 |
veStatRxStateIndicates if data being reassembled and transmittedro Enumeration .1.3.6.1.4.1.251.1.1.20.2.1.4 |
veTxCntCount of Cells transmitted from switch fabricro Counter .1.3.6.1.4.1.251.1.1.20.2.1.5 |
veRxCntCount of Cells received into switch fabricro Counter .1.3.6.1.4.1.251.1.1.20.2.1.6 |
veOflCntCount of 1S intervals during which RX FIFO overflowed or underflowedro Counter .1.3.6.1.4.1.251.1.1.20.2.1.7 |
veUflCntCount of 1S intervals during which RX FIFO underflowedro Counter .1.3.6.1.4.1.251.1.1.20.2.1.8 |
veDisCntCount of 1S intervals during which cells were discardedro Counter .1.3.6.1.4.1.251.1.1.20.2.1.9 |
veInvCntCount of 1S intervals during which cells were inventedro Counter .1.3.6.1.4.1.251.1.1.20.2.1.10 |
veResCntCount of 1S intervals during which AAL1 resync occurredro Counter .1.3.6.1.4.1.251.1.1.20.2.1.11 |
veFifoLvlCntNumber of Cells currently in FIFOro Counter .1.3.6.1.4.1.251.1.1.20.2.1.12 |
dv2SystemClocks OBJECT IDENTIFIER .1.3.6.1.4.1.251.1.1.21 |
autoRevertAutomatic Revert after Timing Source Recoveryrw Enumeration .1.3.6.1.4.1.251.1.1.21.1 |
revertTimerRevert Timer in Secondsrw INTEGER .1.3.6.1.4.1.251.1.1.21.2 |
forceRevertForce Immediate Revertrw Enumeration .1.3.6.1.4.1.251.1.1.21.3 |
forceSecondaryForce Secondary Source Timingrw Enumeration .1.3.6.1.4.1.251.1.1.21.4 |
alarmStatusTiming Alarm Statusro Enumeration .1.3.6.1.4.1.251.1.1.21.5 |
inServiceCard in Servicero Enumeration .1.3.6.1.4.1.251.1.1.21.6 |
primaryClockTable SEQUENCE OF PrimaryEntry .1.3.6.1.4.1.251.1.1.21.7 |
primaryEntry PrimaryEntry .1.3.6.1.4.1.251.1.1.21.7.1 |
pIndexEntry Indexro INTEGER .1.3.6.1.4.1.251.1.1.21.7.1.1 |
pValidSourceValid Timing Sourcero Enumeration .1.3.6.1.4.1.251.1.1.21.7.1.2 |
pOnOffLineOn / Off line Togglerw Enumeration .1.3.6.1.4.1.251.1.1.21.7.1.3 |
pSlotNumberPrimary Source Slot Numberrw INTEGER .1.3.6.1.4.1.251.1.1.21.7.1.4 |
pSysRefSelectSystem Reference Selectrw Enumeration .1.3.6.1.4.1.251.1.1.21.7.1.5 |
pActiveTimingSourceActive Timing Referencero Enumeration .1.3.6.1.4.1.251.1.1.21.7.1.6 |
pInputLineOkInput Line OKro Enumeration .1.3.6.1.4.1.251.1.1.21.7.1.7 |
pSysRefTimingOkSystem Reference Timing OKro Enumeration .1.3.6.1.4.1.251.1.1.21.7.1.8 |
secondaryClockTable SEQUENCE OF SecondaryEntry .1.3.6.1.4.1.251.1.1.21.8 |
secondaryEntry SecondaryEntry .1.3.6.1.4.1.251.1.1.21.8.1 |
sIndexEntry Indexro INTEGER .1.3.6.1.4.1.251.1.1.21.8.1.1 |
sValidSourceValid Timing Sourcero Enumeration .1.3.6.1.4.1.251.1.1.21.8.1.2 |
sOnOffLineOn / Off line Togglerw Enumeration .1.3.6.1.4.1.251.1.1.21.8.1.3 |
sSlotNumberSecondary Source Slot Numberrw INTEGER .1.3.6.1.4.1.251.1.1.21.8.1.4 |
sSysRefSelectSystem Reference Selectrw Enumeration .1.3.6.1.4.1.251.1.1.21.8.1.5 |
sActiveTimingSourceActive Timing Referencero Enumeration .1.3.6.1.4.1.251.1.1.21.8.1.6 |
sInputLineOkInput Line OKro Enumeration .1.3.6.1.4.1.251.1.1.21.8.1.7 |
sSysRefTimingOkSystem Reference Timing OKro Enumeration .1.3.6.1.4.1.251.1.1.21.8.1.8 |
str3ConfiguredCAT Card presentro Enumeration .1.3.6.1.4.1.251.1.1.21.9 |
pCATcontrolTable SEQUENCE OF PCATcontrolEntry .1.3.6.1.4.1.251.1.1.21.10 |
pCATcontrolEntry PCATcontrolEntry .1.3.6.1.4.1.251.1.1.21.10.1 |
pccIndexEntry Indexro INTEGER .1.3.6.1.4.1.251.1.1.21.10.1.1 |
pccatlimtypeType of CAT LIMrw Enumeration .1.3.6.1.4.1.251.1.1.21.10.1.2 |
pccatsendcodeSend code to NTM LIMrw Enumeration .1.3.6.1.4.1.251.1.1.21.10.1.3 |
pccatactivateActivate NTM Coderw Enumeration .1.3.6.1.4.1.251.1.1.21.10.1.4 |
pccatsendconfigSend Configuration to NTM LIMrw Enumeration .1.3.6.1.4.1.251.1.1.21.10.1.5 |
pccatbytestransferredCode bytes transferred to NTM LIMro INTEGER .1.3.6.1.4.1.251.1.1.21.10.1.6 |
pccatfilexferstatFile transfer status as reported by Slot 0ro Enumeration .1.3.6.1.4.1.251.1.1.21.10.1.7 |
pcatforcesecextForce the secondary externalrw Enumeration .1.3.6.1.4.1.251.1.1.21.10.1.8 |
pcatforcesecstr3Force the secondary stratum 3rw Enumeration .1.3.6.1.4.1.251.1.1.21.10.1.9 |
pcatcommandInternal Usero Enumeration .1.3.6.1.4.1.251.1.1.21.10.1.10 |
pcatplaceholder1Placeholder for future MIB changesro Enumeration .1.3.6.1.4.1.251.1.1.21.10.1.11 |
pcatplaceholder2Placeholder for future MIB changesro Enumeration .1.3.6.1.4.1.251.1.1.21.10.1.12 |
pcconofflinePut NTM LIM on or offlinerw Enumeration .1.3.6.1.4.1.251.1.1.21.10.1.13 |
sCATcontrolTable SEQUENCE OF SCATcontrolEntry .1.3.6.1.4.1.251.1.1.21.11 |
sCATcontrolEntry SCATcontrolEntry .1.3.6.1.4.1.251.1.1.21.11.1 |
sccIndexEntry Indexro INTEGER .1.3.6.1.4.1.251.1.1.21.11.1.1 |
sccatlimtypeType of NTM LIMrw Enumeration .1.3.6.1.4.1.251.1.1.21.11.1.2 |
sccatsendcodeDownload code to NTM LIMrw Enumeration .1.3.6.1.4.1.251.1.1.21.11.1.3 |
sccatactivateActivate NTM Coderw Enumeration .1.3.6.1.4.1.251.1.1.21.11.1.4 |
sccatsendconfigDownload Configuration to NTM LIMrw Enumeration .1.3.6.1.4.1.251.1.1.21.11.1.5 |
sccatbytestransferredCode bytes transferred to NTM LIMro INTEGER .1.3.6.1.4.1.251.1.1.21.11.1.6 |
sccatfilexferstatFile transfer status as reported by Slot 0ro Enumeration .1.3.6.1.4.1.251.1.1.21.11.1.7 |
scatcommandInternal Usero Enumeration .1.3.6.1.4.1.251.1.1.21.11.1.8 |
scatplaceholder1Placeholder for future MIB changesro Enumeration .1.3.6.1.4.1.251.1.1.21.11.1.9 |
scatplaceholder2Placeholder for future MIB changesro Enumeration .1.3.6.1.4.1.251.1.1.21.11.1.10 |
scconofflinePut NTM LIM on or offlinerw Enumeration .1.3.6.1.4.1.251.1.1.21.11.1.11 |
pCATstatusTable SEQUENCE OF PCATstatusEntry .1.3.6.1.4.1.251.1.1.21.12 |
pCATstatusEntry PCATstatusEntry .1.3.6.1.4.1.251.1.1.21.12.1 |
pscIndexEntry Indexro INTEGER .1.3.6.1.4.1.251.1.1.21.12.1.1 |
pscatlimtypeType of NTM LIM detectedro Enumeration .1.3.6.1.4.1.251.1.1.21.12.1.2 |
psCATFFrevisionNTM LIM Code Revisionro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.251.1.1.21.12.1.3 |
psCATBootrevisionNTM LIM Boot Revisionro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.251.1.1.21.12.1.4 |
pscatfilestatusFlash file statusro Enumeration .1.3.6.1.4.1.251.1.1.21.12.1.5 |
psCATfilerevisionNTM LIM file Revisionro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.251.1.1.21.12.1.6 |
psCATHWrevisionNTM LIM Hardware Revisionro INTEGER .1.3.6.1.4.1.251.1.1.21.12.1.7 |
pscatmodeOperating Mode of NTM LIMro Enumeration .1.3.6.1.4.1.251.1.1.21.12.1.8 |
pscaterrorcodeNTM LIM Error Codero Enumeration .1.3.6.1.4.1.251.1.1.21.12.1.9 |
pscatplaceholder1Placeholder for future MIB changesro Enumeration .1.3.6.1.4.1.251.1.1.21.12.1.10 |
pscatplaceholder2Placeholder for future MIB changesro Enumeration .1.3.6.1.4.1.251.1.1.21.12.1.11 |
sCATstatusTable SEQUENCE OF SCATstatusEntry .1.3.6.1.4.1.251.1.1.21.13 |
sCATstatusEntry SCATstatusEntry .1.3.6.1.4.1.251.1.1.21.13.1 |
sscIndexEntry Indexro INTEGER .1.3.6.1.4.1.251.1.1.21.13.1.1 |
sscatlimtypeType of NTM LIMro Enumeration .1.3.6.1.4.1.251.1.1.21.13.1.2 |
ssCATFFrevisionNTM LIM Code Revisionro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.251.1.1.21.13.1.3 |
ssCATBootrevisionNTM LIM Boot Revisionro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.251.1.1.21.13.1.4 |
sscatfilestatusFlash file statusro Enumeration .1.3.6.1.4.1.251.1.1.21.13.1.5 |
ssCATfilerevisionNTM LIM file Revisionro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.251.1.1.21.13.1.6 |
ssCATHWrevisionNTM LIM Hardware Revisionro INTEGER .1.3.6.1.4.1.251.1.1.21.13.1.7 |
sscatmodeOperating mode of NTM LIMro Enumeration .1.3.6.1.4.1.251.1.1.21.13.1.8 |
sscaterrorcodeNTM LIM Error Codero Enumeration .1.3.6.1.4.1.251.1.1.21.13.1.9 |
sscatplaceholder1Placeholder for future MIB changesro Enumeration .1.3.6.1.4.1.251.1.1.21.13.1.10 |
sscatplaceholder2Placeholder for future MIB changesro Enumeration .1.3.6.1.4.1.251.1.1.21.13.1.11 |
pCATStratum3ConfigTable SEQUENCE OF PCATStratum3ConfigEntry .1.3.6.1.4.1.251.1.1.21.14 |
pCATStratum3ConfigEntry PCATStratum3ConfigEntry .1.3.6.1.4.1.251.1.1.21.14.1 |
ps3cIndexEntry Indexro INTEGER .1.3.6.1.4.1.251.1.1.21.14.1.1 |
pcatstr3listenerConfigures Stratum 3 Referencerw Enumeration .1.3.6.1.4.1.251.1.1.21.14.1.2 |
pcatstr3oscillatorConfigures Stratum 3 Moderw Enumeration .1.3.6.1.4.1.251.1.1.21.14.1.3 |
pcatstr3forcesecondaryDisables Stratum 3 Driver on Primary NTM LIM onlyrw Enumeration .1.3.6.1.4.1.251.1.1.21.14.1.4 |
pcatstr3reconfigureRe-configure Primary Stratum 3rw Enumeration .1.3.6.1.4.1.251.1.1.21.14.1.5 |
sCATStratum3ConfigTable SEQUENCE OF SCATStratum3ConfigEntry .1.3.6.1.4.1.251.1.1.21.15 |
sCATStratum3ConfigEntry SCATStratum3ConfigEntry .1.3.6.1.4.1.251.1.1.21.15.1 |
ss3cIndexEntry Indexro INTEGER .1.3.6.1.4.1.251.1.1.21.15.1.1 |
scatstr3listenerConfigures Stratum 3 Referencerw Enumeration .1.3.6.1.4.1.251.1.1.21.15.1.2 |
scatstr3oscillatorConfigures Stratum 3 Moderw Enumeration .1.3.6.1.4.1.251.1.1.21.15.1.3 |
scatstr3reconfigureRe-configure Secondary Stratum 3rw Enumeration .1.3.6.1.4.1.251.1.1.21.15.1.4 |
pCATStratum3StatusTable SEQUENCE OF PCATStratum3StatusEntry .1.3.6.1.4.1.251.1.1.21.16 |
pCATStratum3StatusEntry PCATStratum3StatusEntry .1.3.6.1.4.1.251.1.1.21.16.1 |
ps3sIndexEntry Indexro INTEGER .1.3.6.1.4.1.251.1.1.21.16.1.1 |
pcatstr3listenerstatusWhat the Stratum 3 is referencing toro Enumeration .1.3.6.1.4.1.251.1.1.21.16.1.2 |
pcatstr3driverstatusWhat the Stratum 3 output is drivingro Enumeration .1.3.6.1.4.1.251.1.1.21.16.1.3 |
pcatstr3oscstatusStratum 3 oscillator statusro Enumeration .1.3.6.1.4.1.251.1.1.21.16.1.4 |
sCATStratum3StatusTable SEQUENCE OF SCATStratum3StatusEntry .1.3.6.1.4.1.251.1.1.21.17 |
sCATStratum3StatusEntry SCATStratum3StatusEntry .1.3.6.1.4.1.251.1.1.21.17.1 |
ss3sIndexEntry Indexro INTEGER .1.3.6.1.4.1.251.1.1.21.17.1.1 |
scatstr3listenerstatusWhat the Stratum 3 Listener is referencingro Enumeration .1.3.6.1.4.1.251.1.1.21.17.1.2 |
scatstr3driverstatusWhat the Stratum 3 output is drivingro Enumeration .1.3.6.1.4.1.251.1.1.21.17.1.3 |
scatstr3oscstatusStratum 3 oscillator statusro Enumeration .1.3.6.1.4.1.251.1.1.21.17.1.4 |
pCATBitsConfigTable SEQUENCE OF PCATBitsConfigEntry .1.3.6.1.4.1.251.1.1.21.18 |
pCATBitsConfigEntry PCATBitsConfigEntry .1.3.6.1.4.1.251.1.1.21.18.1 |
pbcIndexEntry Indexro INTEGER .1.3.6.1.4.1.251.1.1.21.18.1.1 |
pbcds1V2TxLineLnSelect transmit line lengthrw Enumeration .1.3.6.1.4.1.251.1.1.21.18.1.2 |
pbcplaceholder1Future Userw Enumeration .1.3.6.1.4.1.251.1.1.21.18.1.3 |
pbcV2FRMRModeDS1 Framing options.rw Enumeration .1.3.6.1.4.1.251.1.1.21.18.1.4 |
pbcds1V2CodingT1 Line Coderw Enumeration .1.3.6.1.4.1.251.1.1.21.18.1.5 |
pbcV2LbLoopback Selection DS1rw Enumeration .1.3.6.1.4.1.251.1.1.21.18.1.6 |
pbcclrperfClear the Performance Countersrw Enumeration .1.3.6.1.4.1.251.1.1.21.18.1.7 |
pbcreconfigureRe-configure Primary Externalrw Enumeration .1.3.6.1.4.1.251.1.1.21.18.1.9 |
sCATBitsConfigTable SEQUENCE OF SCATBitsConfigEntry .1.3.6.1.4.1.251.1.1.21.19 |
sCATBitsConfigEntry SCATBitsConfigEntry .1.3.6.1.4.1.251.1.1.21.19.1 |
sbcIndexEntry Indexro INTEGER .1.3.6.1.4.1.251.1.1.21.19.1.1 |
sbcds1V2TxLineLnSelect transmit line lengthrw Enumeration .1.3.6.1.4.1.251.1.1.21.19.1.2 |
sbcplaceholder1Future Userw Enumeration .1.3.6.1.4.1.251.1.1.21.19.1.3 |
sbcV2FRMRModeDS1 Framing options.rw Enumeration .1.3.6.1.4.1.251.1.1.21.19.1.4 |
sbcds1V2CodingT1 Line Codingrw Enumeration .1.3.6.1.4.1.251.1.1.21.19.1.5 |
sbcV2LbLoopback Selectionrw Enumeration .1.3.6.1.4.1.251.1.1.21.19.1.6 |
sbcclrperfClear the Performance Countersrw Enumeration .1.3.6.1.4.1.251.1.1.21.19.1.7 |
sbcreconfigureRe-configure Secondary Externalrw Enumeration .1.3.6.1.4.1.251.1.1.21.19.1.8 |
pCATBitsStatusTableDs1/E1 Bits Status Table SEQUENCE OF PCATBitsStatusEntry .1.3.6.1.4.1.251.1.1.21.20 |
pCATBitsStatusEntry PCATBitsStatusEntry .1.3.6.1.4.1.251.1.1.21.20.1 |
pbsIndexEntry Indexro INTEGER .1.3.6.1.4.1.251.1.1.21.20.1.1 |
pbslineokIs the line OKro Enumeration .1.3.6.1.4.1.251.1.1.21.20.1.2 |
pbsV2RxAISReceive DS1 AIS(Blue)Alarm status.ro Enumeration .1.3.6.1.4.1.251.1.1.21.20.1.3 |
pbsV2RxLOSReceive DS1 LOS status.ro Enumeration .1.3.6.1.4.1.251.1.1.21.20.1.4 |
pbsV2RxOOFReceive DS1 OOF status.ro Enumeration .1.3.6.1.4.1.251.1.1.21.20.1.5 |
pbsV2RxBERReceive DS1 BER status.ro Enumeration .1.3.6.1.4.1.251.1.1.21.20.1.6 |
pbsV2RxOOFCntReceive DS1 OOF count.ro INTEGER .1.3.6.1.4.1.251.1.1.21.20.1.7 |
pbsV2RxBERCntReceive DS1 BEE count.ro INTEGER .1.3.6.1.4.1.251.1.1.21.20.1.8 |
pbsV2RxLOSCntReceive DS1 LOS count.ro INTEGER .1.3.6.1.4.1.251.1.1.21.20.1.9 |
pbsV2LCVCntReceive DS1 LCV count.ro INTEGER .1.3.6.1.4.1.251.1.1.21.20.1.10 |
sCATBitsStatusTableDs1/E1 Bits Status Table SEQUENCE OF SCATBitsStatusEntry .1.3.6.1.4.1.251.1.1.21.21 |
sCATBitsStatusEntry SCATBitsStatusEntry .1.3.6.1.4.1.251.1.1.21.21.1 |
sbsIndexEntry Indexro INTEGER .1.3.6.1.4.1.251.1.1.21.21.1.1 |
sbslineokIs the line OKro Enumeration .1.3.6.1.4.1.251.1.1.21.21.1.2 |
sbsV2RxAISReceive DS1 AIS(Blue)Alarm status.ro Enumeration .1.3.6.1.4.1.251.1.1.21.21.1.3 |
sbsV2RxLOSReceive DS1 LOS status.ro Enumeration .1.3.6.1.4.1.251.1.1.21.21.1.4 |
sbsV2RxOOFReceive DS1 OOF status.ro Enumeration .1.3.6.1.4.1.251.1.1.21.21.1.5 |
sbsV2RxBERReceive DS1 BER status.ro Enumeration .1.3.6.1.4.1.251.1.1.21.21.1.6 |
sbsV2RxOOFCntReceive DS1 OOF Counts.ro INTEGER .1.3.6.1.4.1.251.1.1.21.21.1.7 |
sbsV2RxBERCntReceive DS1 BEE Counts.ro INTEGER .1.3.6.1.4.1.251.1.1.21.21.1.8 |
sbsV2RxLOSCntReceive DS1/E1 LOS Counts.ro INTEGER .1.3.6.1.4.1.251.1.1.21.21.1.9 |
sbsV2LCVCntReceive DS1 AIS Counts.ro INTEGER .1.3.6.1.4.1.251.1.1.21.21.1.10 |
pCATDerConfigTable SEQUENCE OF PCATDerConfigEntry .1.3.6.1.4.1.251.1.1.21.22 |
pCATDerConfigEntry PCATDerConfigEntry .1.3.6.1.4.1.251.1.1.21.22.1 |
pdcIndexEntry Indexro INTEGER .1.3.6.1.4.1.251.1.1.21.22.1.1 |
pdcds1V2TxLineLnSelect transmit line lengthrw Enumeration .1.3.6.1.4.1.251.1.1.21.22.1.2 |
pdcplaceholder1Future Userw Enumeration .1.3.6.1.4.1.251.1.1.21.22.1.3 |
pdcV2FRMRModeDS1 Framing options.rw Enumeration .1.3.6.1.4.1.251.1.1.21.22.1.4 |
pdcds1V2CodingLine Coderw Enumeration .1.3.6.1.4.1.251.1.1.21.22.1.5 |
pdcV2LbLoopback Selectionrw Enumeration .1.3.6.1.4.1.251.1.1.21.22.1.6 |
pdcclrperfClear the performance countersrw Enumeration .1.3.6.1.4.1.251.1.1.21.22.1.7 |
pdcreconfigureRe-configure Primary Linerw Enumeration .1.3.6.1.4.1.251.1.1.21.22.1.8 |
sCATDerConfigTable SEQUENCE OF SCATDerConfigEntry .1.3.6.1.4.1.251.1.1.21.23 |
sCATDerConfigEntry SCATDerConfigEntry .1.3.6.1.4.1.251.1.1.21.23.1 |
sdcIndexEntry Indexro INTEGER .1.3.6.1.4.1.251.1.1.21.23.1.1 |
sdcds1V2TxLineLnSelect transmit line lengthrw Enumeration .1.3.6.1.4.1.251.1.1.21.23.1.2 |
sdcplaceholder1Future Userw Enumeration .1.3.6.1.4.1.251.1.1.21.23.1.3 |
sdcV2FRMRModeDS1 Framing options.rw Enumeration .1.3.6.1.4.1.251.1.1.21.23.1.4 |
sdcds1V2CodingLine Codingrw Enumeration .1.3.6.1.4.1.251.1.1.21.23.1.5 |
sdcV2LbLoopback Selection DS1rw Enumeration .1.3.6.1.4.1.251.1.1.21.23.1.6 |
sdcclrperfClear the Performance Countersrw Enumeration .1.3.6.1.4.1.251.1.1.21.23.1.7 |
sdcreconfigureRe-configure Secondary Linerw Enumeration .1.3.6.1.4.1.251.1.1.21.23.1.8 |
pCATDerStatusTableDs1/E1 Derived Status Table SEQUENCE OF PCATDerStatusEntry .1.3.6.1.4.1.251.1.1.21.24 |
pCATDerStatusEntry PCATDerStatusEntry .1.3.6.1.4.1.251.1.1.21.24.1 |
pdsIndexEntry Indexro INTEGER .1.3.6.1.4.1.251.1.1.21.24.1.1 |
pdslineokIs the line OKro Enumeration .1.3.6.1.4.1.251.1.1.21.24.1.2 |
pdsV2TxReferenceTransmit Reference Statusro Enumeration .1.3.6.1.4.1.251.1.1.21.24.1.3 |
pdsV2RxAISReceive DS1 AIS(Blue)Alarm status.ro Enumeration .1.3.6.1.4.1.251.1.1.21.24.1.4 |
pdsV2RxLOSReceive DS1 LOS status.ro Enumeration .1.3.6.1.4.1.251.1.1.21.24.1.5 |
pdsV2RxOOFReceive DS1 OOF status.ro Enumeration .1.3.6.1.4.1.251.1.1.21.24.1.6 |
pdsV2RxBERReceive DS1 BER status.ro Enumeration .1.3.6.1.4.1.251.1.1.21.24.1.7 |
pdsV2RxOOFCntReceive DS1 OOF count.ro INTEGER .1.3.6.1.4.1.251.1.1.21.24.1.8 |
pdsV2RxBERCntReceive DS1 BEE count.ro INTEGER .1.3.6.1.4.1.251.1.1.21.24.1.9 |
pdsV2RxLOSCntReceive DS1 LOS count.ro INTEGER .1.3.6.1.4.1.251.1.1.21.24.1.10 |
pdsV2LCVCntReceive DS1 AIS count.ro INTEGER .1.3.6.1.4.1.251.1.1.21.24.1.11 |
sCATDerStatusTableDs1/E1 Derived Status Table SEQUENCE OF SCATDerStatusEntry .1.3.6.1.4.1.251.1.1.21.25 |
sCATDerStatusEntry SCATDerStatusEntry .1.3.6.1.4.1.251.1.1.21.25.1 |
sdsIndexEntry Indexro INTEGER .1.3.6.1.4.1.251.1.1.21.25.1.1 |
sdslineokIs the line OKro Enumeration .1.3.6.1.4.1.251.1.1.21.25.1.2 |
sdsV2TxReferenceTransmit Reference Statusro Enumeration .1.3.6.1.4.1.251.1.1.21.25.1.3 |
sdsV2RxAISReceive DS1 AIS(Blue)Alarm status.ro Enumeration .1.3.6.1.4.1.251.1.1.21.25.1.4 |
sdsV2RxLOSReceive DS1 LOS status.ro Enumeration .1.3.6.1.4.1.251.1.1.21.25.1.5 |
sdsV2RxOOFReceive DS1 OOF status.ro Enumeration .1.3.6.1.4.1.251.1.1.21.25.1.6 |
sdsV2RxBERReceive DS1 BER status.ro Enumeration .1.3.6.1.4.1.251.1.1.21.25.1.7 |
sdsV2RxOOFCntReceive DS1 OOF count.ro INTEGER .1.3.6.1.4.1.251.1.1.21.25.1.8 |
sdsV2RxBERCntReceive DS1 BEE count.ro INTEGER .1.3.6.1.4.1.251.1.1.21.25.1.9 |
sdsV2RxLOSCntReceive DS1 LOS count.ro INTEGER .1.3.6.1.4.1.251.1.1.21.25.1.10 |
sdsV2LCVCntReceive DS1 AIS count.ro INTEGER .1.3.6.1.4.1.251.1.1.21.25.1.11 |
sysClkAlarmErrDefines the error type for the current clock alarmro Enumeration .1.3.6.1.4.1.251.1.1.21.26 |
mjlimSlipLine OBJECT IDENTIFIER .1.3.6.1.4.1.251.1.1.22 |
jpegSlipIpIP address of SLIP line.rw IpAddress .1.3.6.1.4.1.251.1.1.22.1 |
jpegSlipMaskMask for SLIP line.rw IpAddress .1.3.6.1.4.1.251.1.1.22.2 |
jpegSlipRemoteIpIP address of remote end of SLIP line.rw IpAddress .1.3.6.1.4.1.251.1.1.22.3 |
jpegSlipSpeedBaud rate of SLIP serial line.rw Enumeration .1.3.6.1.4.1.251.1.1.22.4 |
mjlimSystem OBJECT IDENTIFIER .1.3.6.1.4.1.251.1.1.23 |
limSysStateM-JPEG LIM System Statero Enumeration .1.3.6.1.4.1.251.1.1.23.1 |
limSysFaultM-JPEG LIM Hardware Fault - front panel lampro Enumeration .1.3.6.1.4.1.251.1.1.23.2 |
limSysCompErrM-JPEG LIM Compression Error - front panel lampro Enumeration .1.3.6.1.4.1.251.1.1.23.3 |
limSysDecompErrM-JPEG LIM Decompression Error - front panel lampro Enumeration .1.3.6.1.4.1.251.1.1.23.4 |
limSysVideoInM-JPEG LIM Video Input Present - front panel lampro Enumeration .1.3.6.1.4.1.251.1.1.23.5 |
limSysVideoOutM-JPEG LIM Video Output Active - front panel lampro Enumeration .1.3.6.1.4.1.251.1.1.23.6 |
limSysStartModeM-JPEG LIM Default Startup moderw Enumeration .1.3.6.1.4.1.251.1.1.23.30 |
vidInCfg OBJECT IDENTIFIER .1.3.6.1.4.1.251.1.1.24 |
vidInJpegM-JPEG LIM Video Input JPEG moderw Enumeration .1.3.6.1.4.1.251.1.1.24.1 |
vidInRateM-JPEG LIM Video Input Channel Bit Raterw Enumeration .1.3.6.1.4.1.251.1.1.24.2 |
vidInProvModeM-JPEG LIM Video Input Provisioning Moderw Enumeration .1.3.6.1.4.1.251.1.1.24.3 |
vidInFrameRateM-JPEG LIM Video Input Frame Raterw Enumeration .1.3.6.1.4.1.251.1.1.24.4 |
vidInWindowSizeM-JPEG LIM Video Input Window sizerw Enumeration .1.3.6.1.4.1.251.1.1.24.5 |
vidInQuanFactorM-JPEG LIM Video Input Quantization factorrw INTEGER .1.3.6.1.4.1.251.1.1.24.6 |
vidInTransModeM-JPEG LIM Video Input Transmit Moderw Enumeration .1.3.6.1.4.1.251.1.1.24.7 |
vidInStandM-JPEG LIM Video Input Standardrw Enumeration .1.3.6.1.4.1.251.1.1.24.8 |
vidInVcrModeM-JPEG LIM Video Input VCR moderw Enumeration .1.3.6.1.4.1.251.1.1.24.9 |
vidInAnLpbkM-JPEG LIM Video Input Analog Loopbackrw Enumeration .1.3.6.1.4.1.251.1.1.24.10 |
vidInTestM-JPEG LIM Video Input Test Patternrw Enumeration .1.3.6.1.4.1.251.1.1.24.11 |
vidOutCfg OBJECT IDENTIFIER .1.3.6.1.4.1.251.1.1.25 |
vidOutJpegM-JPEG LIM Video Output JPEG Moderw Enumeration .1.3.6.1.4.1.251.1.1.25.1 |
vidOutStandM-JPEG LIM Video Output Standardrw Enumeration .1.3.6.1.4.1.251.1.1.25.2 |
vidOutSourceM-JPEG LIM Video Output Timing Sourcerw Enumeration .1.3.6.1.4.1.251.1.1.25.3 |
vidOutUnLpbM-JPEG LIM Video Output Uncompressed Loopbackrw Enumeration .1.3.6.1.4.1.251.1.1.25.4 |
vidOutIdleSrcM-JPEG LIM Video Output Idle Sourcerw Enumeration .1.3.6.1.4.1.251.1.1.25.5 |
vidOutChnlLpbkM-JPEG LIM Video Output Channel Loopbackrw Enumeration .1.3.6.1.4.1.251.1.1.25.6 |
vidInSta OBJECT IDENTIFIER .1.3.6.1.4.1.251.1.1.26 |
vidInStateM-JPEG LIM Video Input Statero Enumeration .1.3.6.1.4.1.251.1.1.26.1 |
vidInPresM-JPEG LIM Video Input Present Indicatorro Enumeration .1.3.6.1.4.1.251.1.1.26.2 |
vidInCurQFactorM-JPEG LIM Video Input Current Quality Factorro INTEGER .1.3.6.1.4.1.251.1.1.26.3 |
vidInCurFrameRateM-JPEG LIM Video Input Current Frame Ratero INTEGER .1.3.6.1.4.1.251.1.1.26.4 |
vidInAvgBitRateM-JPEG LIM Video Input Average Bitrate (Mpbs)ro INTEGER .1.3.6.1.4.1.251.1.1.26.5 |
vidInPeakBitRateM-JPEG LIM Video Input Peak Bitrate (Mbps)ro INTEGER .1.3.6.1.4.1.251.1.1.26.6 |
vidInSubSampleM-JPEG LIM Video Input Field Subsample Statusro Enumeration .1.3.6.1.4.1.251.1.1.26.7 |
vidInCompCntM-JPEG LIM Video Input Compressed Packet Countro Counter .1.3.6.1.4.1.251.1.1.26.8 |
vidInSkipCntM-JPEG LIM Video Input Skipped Packet Countro Counter .1.3.6.1.4.1.251.1.1.26.9 |
vidInBuffOvfM-JPEG LIM Video Input Buffer Controller Overflow Countro Counter .1.3.6.1.4.1.251.1.1.26.10 |
vidInImageErrM-JPEG LIM Video Input JPEG Chip FIFO Overflowro Counter .1.3.6.1.4.1.251.1.1.26.11 |
vidInFldSynErrM-JPEG LIM Video Input Field Synchronization Errorsro Counter .1.3.6.1.4.1.251.1.1.26.12 |
vidInCompErrM-JPEG LIM Video Input Compression Errorsro Counter .1.3.6.1.4.1.251.1.1.26.13 |
vidInBufLevelM-JPEG LIM Video Input Buffer Fill Level (%)ro INTEGER .1.3.6.1.4.1.251.1.1.26.14 |
vidInFailReasonM-JPEG LIM Video Input Fail Reasonro Enumeration .1.3.6.1.4.1.251.1.1.26.15 |
vidOutSta OBJECT IDENTIFIER .1.3.6.1.4.1.251.1.1.27 |
vidOutStateM-JPEG LIM Video Output statero Enumeration .1.3.6.1.4.1.251.1.1.27.1 |
vidOutRateM-JPEG LIM Video Output Bitrate (Mbps)ro INTEGER .1.3.6.1.4.1.251.1.1.27.2 |
vidOutFrameRateM-JPEG LIM Video Output Frame Ratero INTEGER .1.3.6.1.4.1.251.1.1.27.3 |
vidOutWindowWidthM-JPEG LIM Video Output Window Widthro INTEGER .1.3.6.1.4.1.251.1.1.27.4 |
vidOutWindowHeightM-JPEG LIM Video Output Window Heightro INTEGER .1.3.6.1.4.1.251.1.1.27.5 |
vidOutChnlLockM-JPEG LIM Video Output Channel Lock Indicatorro Enumeration .1.3.6.1.4.1.251.1.1.27.6 |
vidOutPacketsM-JPEG LIM Video Output Packets Received Countro Counter .1.3.6.1.4.1.251.1.1.27.7 |
vidOutPlayedM-JPEG LIM Video Output Packets Played Countro Counter .1.3.6.1.4.1.251.1.1.27.8 |
vidOutSkippedM-JPEG LIM Video Output Skipped Packet Countro Counter .1.3.6.1.4.1.251.1.1.27.9 |
vidOutChnlErrM-JPEG LIM Video Output Channel Error Countro Counter .1.3.6.1.4.1.251.1.1.27.10 |
vidOutBuffOvfM-JPEG LIM Video Output Buffer Controller Overflow Countro Counter .1.3.6.1.4.1.251.1.1.27.11 |
vidOutImageErrM-JPEG LIM Video Output JPEG Chip Error Countro Counter .1.3.6.1.4.1.251.1.1.27.12 |
vidOutSeqnoErrM-JPEG LIM Video Output Packet Sequence Number Error Countro Counter .1.3.6.1.4.1.251.1.1.27.13 |
vidOutCurrQFactorM-JPEG LIM Video Output Current JPEG Quantization Factorro INTEGER .1.3.6.1.4.1.251.1.1.27.14 |
vidOutStdStatM-JPEG LIM Video Output Standard Statusro Enumeration .1.3.6.1.4.1.251.1.1.27.15 |
vidOutBuffLevelM-JPEG LIM Video Output Buffer Fill Level (%)ro INTEGER .1.3.6.1.4.1.251.1.1.27.16 |
vidOutPktsInBuffM-JPEG LIM Video Output Packets in Bufferro INTEGER .1.3.6.1.4.1.251.1.1.27.17 |
vidOutFailReasonM-JPEG LIM Video Output Fail Reasonro Enumeration .1.3.6.1.4.1.251.1.1.27.18 |
vidOutSrcStsM-JPEG LIM Video Output Timing Source Statusro Enumeration .1.3.6.1.4.1.251.1.1.27.19 |
audInCfg OBJECT IDENTIFIER .1.3.6.1.4.1.251.1.1.28 |
audInLoopBackM-JPEG LIM Audio Input LoopBack Moderw Enumeration .1.3.6.1.4.1.251.1.1.28.1 |
audOutCfg OBJECT IDENTIFIER .1.3.6.1.4.1.251.1.1.29 |
audOutMuteM-JPEG LIM Audio Output Mute Controlrw Enumeration .1.3.6.1.4.1.251.1.1.29.1 |
audOutDigLpbkM-JPEG LIM Audio Digital Loopbackrw Enumeration .1.3.6.1.4.1.251.1.1.29.2 |
audInSta OBJECT IDENTIFIER .1.3.6.1.4.1.251.1.1.30 |
audOutSta OBJECT IDENTIFIER .1.3.6.1.4.1.251.1.1.31 |
audOutLockM-JPEG LIM Audio Output Channel Lock Indicatorro Enumeration .1.3.6.1.4.1.251.1.1.31.1 |
audOutMuteStatM-JPEG LIM Audio Output Mute Statusro Enumeration .1.3.6.1.4.1.251.1.1.31.2 |
dataCfg OBJECT IDENTIFIER .1.3.6.1.4.1.251.1.1.32 |
dataIpIP address of Data Channel.rw IpAddress .1.3.6.1.4.1.251.1.1.32.1 |
dataMaskNetwork Mask for Data Channel.rw IpAddress .1.3.6.1.4.1.251.1.1.32.2 |
dataRemoteIpIP address of remote end of Data Channel.rw IpAddress .1.3.6.1.4.1.251.1.1.32.3 |
dataSta OBJECT IDENTIFIER .1.3.6.1.4.1.251.1.1.33 |
mjlimControl OBJECT IDENTIFIER .1.3.6.1.4.1.251.1.1.34 |
sendFileSelFile to sendrw Enumeration .1.3.6.1.4.1.251.1.1.34.1 |
jpegCurrentFileFile being sentro Enumeration .1.3.6.1.4.1.251.1.1.34.2 |
sendFileStatStatus of file sendro Enumeration .1.3.6.1.4.1.251.1.1.34.3 |
sendFileBytesBytes sentro INTEGER .1.3.6.1.4.1.251.1.1.34.4 |
jpegResetHard/Soft Resetrw Enumeration .1.3.6.1.4.1.251.1.1.34.20 |
jpegSaveCfgSave Configurationrw Enumeration .1.3.6.1.4.1.251.1.1.34.21 |
jpegLoadCfgLoad Configurationrw Enumeration .1.3.6.1.4.1.251.1.1.34.22 |
jpegSWRevJPEG Code Revisionro DisplayString .1.3.6.1.4.1.251.1.1.34.40 |
dv2PDH OBJECT IDENTIFIER .1.3.6.1.4.1.251.1.1.35 |
pdhPLCPTableThis table is used for PLCP configuration and status SEQUENCE OF PdhPLCPEntry .1.3.6.1.4.1.251.1.1.35.1 |
pdhPLCPEntry PdhPLCPEntry .1.3.6.1.4.1.251.1.1.35.1.1 |
pdhPLCPLinkNoLink Numberro INTEGER .1.3.6.1.4.1.251.1.1.35.1.1.1 |
pdhPLCPLinkEnableEnable/Disable Linkrw Enumeration .1.3.6.1.4.1.251.1.1.35.1.1.2 |
pdhPLCPLinkStatusAffectLink Status affect on receiving/transmittingrw Enumeration .1.3.6.1.4.1.251.1.1.35.1.1.3 |
pdhPLCPLinkStateCurrent Link Statero Enumeration .1.3.6.1.4.1.251.1.1.35.1.1.4 |
pdhPLCPPhyModeThe physical framing for linkrw Enumeration .1.3.6.1.4.1.251.1.1.35.1.1.5 |
pdhPLCPModeThe PLCP mode for link.rw Enumeration .1.3.6.1.4.1.251.1.1.35.1.1.6 |
pdhPLCPScramblerEnable/Disable scramblingrw Enumeration .1.3.6.1.4.1.251.1.1.35.1.1.7 |
pdhPLCP0x55Enable/Disable XORing HCS with 0x55rw Enumeration .1.3.6.1.4.1.251.1.1.35.1.1.8 |
pdhPLCPSmdsModeEnable/Disable SMDS moderw Enumeration .1.3.6.1.4.1.251.1.1.35.1.1.9 |
pdhPLCPIdleCellIdle Cell Header Contentsrw Enumeration .1.3.6.1.4.1.251.1.1.35.1.1.10 |
pdhPLCPLoopbackPLCP Loopbackrw Enumeration .1.3.6.1.4.1.251.1.1.35.1.1.11 |
pdhPLCPClearClear PLCP countsrw Enumeration .1.3.6.1.4.1.251.1.1.35.1.1.12 |
pdhPLCPReconfigReconfigure linkrw Enumeration .1.3.6.1.4.1.251.1.1.35.1.1.13 |
pdhPLCPLpbkTimeoutThis parameter is used to set the loopback timeout in minutes.rw INTEGER .1.3.6.1.4.1.251.1.1.35.1.1.14 |
pdhPLCPChipTypePDH Chip Typero Enumeration .1.3.6.1.4.1.251.1.1.35.1.1.32 |
pdhPLCPTXclockThe state of TX clock for this link.ro Enumeration .1.3.6.1.4.1.251.1.1.35.1.1.33 |
pdhPLCPRXclockThe state of RX clock for this link.ro Enumeration .1.3.6.1.4.1.251.1.1.35.1.1.34 |
pdhPLCPTXCellsThe transmit cells count for this link.ro Counter .1.3.6.1.4.1.251.1.1.35.1.1.35 |
pdhPLCPRXCellsThe receive cells count for this link.ro Counter .1.3.6.1.4.1.251.1.1.35.1.1.36 |
pdhPLCPHCSErrsThe header checksum error count for this link.ro Counter .1.3.6.1.4.1.251.1.1.35.1.1.37 |
pdhPLCPLOCDDefectLoss of cell delineation Defectro Enumeration .1.3.6.1.4.1.251.1.1.35.1.1.43 |
pdhPLCPYellowDefectPLCP Yellow Defectro Enumeration .1.3.6.1.4.1.251.1.1.35.1.1.44 |
pdhPLCPLOFDefectPLCP Loss Of Frame Defectro Enumeration .1.3.6.1.4.1.251.1.1.35.1.1.45 |
pdhPLCPLOCDAlarmLoss of cell delineation Alarmro Enumeration .1.3.6.1.4.1.251.1.1.35.1.1.49 |
pdhPLCPYellowAlarmPLCP Yellow Alarmro Enumeration .1.3.6.1.4.1.251.1.1.35.1.1.50 |
pdhPLCPLOFAlarmPLCP Loss Of Frame Alarmro Enumeration .1.3.6.1.4.1.251.1.1.35.1.1.51 |
pdhPLCPFrameErrsNumber of PLCP frame errorsro Counter .1.3.6.1.4.1.251.1.1.35.1.1.56 |
pdhPLCPBIP8ErrsNumber of PLCP BIP-8 errorsro Counter .1.3.6.1.4.1.251.1.1.35.1.1.57 |
pdhPLCPFEBEErrsNumber of PLCP FEBE errorsro Counter .1.3.6.1.4.1.251.1.1.35.1.1.58 |
pdhPLCPESPLCP Errored Secondsro Counter .1.3.6.1.4.1.251.1.1.35.1.1.63 |
pdhPLCPSESPLCP Severely Errored Secondsro Counter .1.3.6.1.4.1.251.1.1.35.1.1.64 |
pdhPLCPUASPLCP Unavailable Secondsro Counter .1.3.6.1.4.1.251.1.1.35.1.1.65 |
pdhPLCPFEESPLCP Far End Errored Secondsro Counter .1.3.6.1.4.1.251.1.1.35.1.1.66 |
pdhPLCPFESESPLCP Far End Severely Errored Secondsro Counter .1.3.6.1.4.1.251.1.1.35.1.1.67 |
pdhPLCPFEUASPLCP Far End Unavailable Secondsro Counter .1.3.6.1.4.1.251.1.1.35.1.1.68 |
pdhDS3TableThis table is used for DS3 config/status supplied by the PLPP chip SEQUENCE OF PdhDS3Entry .1.3.6.1.4.1.251.1.1.35.2 |
pdhDS3Entry PdhDS3Entry .1.3.6.1.4.1.251.1.1.35.2.1 |
pdhDS3TableValidIndicates if table is valid for configured LIMro Enumeration .1.3.6.1.4.1.251.1.1.35.2.1.1 |
pdhDS3LinkNoLink Numberro INTEGER .1.3.6.1.4.1.251.1.1.35.2.1.2 |
pdhDS3FramerDS3 framer moderw Enumeration .1.3.6.1.4.1.251.1.1.35.2.1.3 |
pdhDS3TxAISTransmit AISrw Enumeration .1.3.6.1.4.1.251.1.1.35.2.1.4 |
pdhDS3ClearClear Button for Countersrw Enumeration .1.3.6.1.4.1.251.1.1.35.2.1.5 |
pdhDS3ReconfigReconfigure linkrw Enumeration .1.3.6.1.4.1.251.1.1.35.2.1.6 |
pdhDS3RxFrmFmtReceive framing formatro Enumeration .1.3.6.1.4.1.251.1.1.35.2.1.26 |
pdhDS3RxIDLReceive IDLE statusro Enumeration .1.3.6.1.4.1.251.1.1.35.2.1.27 |
pdhDS3FEACTxmtCode that has been transmitted as a FEAC.ro Enumeration .1.3.6.1.4.1.251.1.1.35.2.1.28 |
pdhDS3LcvsDS3 Line Code Violation countro Counter .1.3.6.1.4.1.251.1.1.35.2.1.33 |
pdhDS3FrameErrsDS3 frame error countro Counter .1.3.6.1.4.1.251.1.1.35.2.1.34 |
pdhDS3ParityErrsDS3 parity error countro Counter .1.3.6.1.4.1.251.1.1.35.2.1.35 |
pdhDS3CbitPrtyErrsDS3 C-bit parity error countro Counter .1.3.6.1.4.1.251.1.1.35.2.1.36 |
pdhDS3FEBEErrsDS3 FEBE error countro Counter .1.3.6.1.4.1.251.1.1.35.2.1.37 |
pdhDS3LOSDefectDS3 Loss of Signal Defectro Enumeration .1.3.6.1.4.1.251.1.1.35.2.1.43 |
pdhDS3OOFDefectDS3 Out of Frame Defectro Enumeration .1.3.6.1.4.1.251.1.1.35.2.1.44 |
pdhDS3AISDefectReceive DS3 AIS Defectro Enumeration .1.3.6.1.4.1.251.1.1.35.2.1.45 |
pdhDS3YellowDefectDS3 Yellow Defectro Enumeration .1.3.6.1.4.1.251.1.1.35.2.1.46 |
pdhDS3ExBERDefectExcessive Bit Error Rate Defectro Enumeration .1.3.6.1.4.1.251.1.1.35.2.1.47 |
pdhDS3LOSAlarmDS3 Loss of Signal Alarmro Enumeration .1.3.6.1.4.1.251.1.1.35.2.1.53 |
pdhDS3LOFAlarmDS3 Loss of Frame Defectro Enumeration .1.3.6.1.4.1.251.1.1.35.2.1.54 |
pdhDS3AISAlarmReceive DS3 AIS Defectro Enumeration .1.3.6.1.4.1.251.1.1.35.2.1.55 |
pdhDS3YellowAlarmDS3 Yellow Alarmro Enumeration .1.3.6.1.4.1.251.1.1.35.2.1.56 |
pdhDS3ExBERAlarmExcessive Bit Error Rate Alarmro Enumeration .1.3.6.1.4.1.251.1.1.35.2.1.57 |
pdhDS3LESLine Errored Secondsro Counter .1.3.6.1.4.1.251.1.1.35.2.1.63 |
pdhDS3LSESLine Severely Errored Secondsro Counter .1.3.6.1.4.1.251.1.1.35.2.1.64 |
pdhDS3ESErrored Secondsro Counter .1.3.6.1.4.1.251.1.1.35.2.1.65 |
pdhDS3ES2Secondary Errored Seconds (C-bit mode only)ro Counter .1.3.6.1.4.1.251.1.1.35.2.1.66 |
pdhDS3SESSeverely Errored Secondsro Counter .1.3.6.1.4.1.251.1.1.35.2.1.67 |
pdhDS3SES2Secondary Severely Errored Seconds (C-bit mode only)ro Counter .1.3.6.1.4.1.251.1.1.35.2.1.68 |
pdhDS3AISSAIS Secondsro Counter .1.3.6.1.4.1.251.1.1.35.2.1.69 |
pdhDS3UASUnavailable Secondsro Counter .1.3.6.1.4.1.251.1.1.35.2.1.70 |
pdhDS3FarEndESFar End Errored Secondsro Counter .1.3.6.1.4.1.251.1.1.35.2.1.71 |
pdhDS3FarEndSESFar End Severely Errored Secondsro Counter .1.3.6.1.4.1.251.1.1.35.2.1.72 |
pdhDS3FarEndUASFar End Unavailable Secondsro Counter .1.3.6.1.4.1.251.1.1.35.2.1.73 |
pdhE3TableThis table is used for E3 config/status supplied by the PLPP chip SEQUENCE OF PdhE3Entry .1.3.6.1.4.1.251.1.1.35.3 |
pdhE3Entry PdhE3Entry .1.3.6.1.4.1.251.1.1.35.3.1 |
pdhE3TableValidIndicates if table is valid for configured LIMro Enumeration .1.3.6.1.4.1.251.1.1.35.3.1.1 |
pdhE3LinkNoLink Numberro INTEGER .1.3.6.1.4.1.251.1.1.35.3.1.2 |
pdhE3FramerE3 framer moderw Enumeration .1.3.6.1.4.1.251.1.1.35.3.1.3 |
pdhE3ClearClear Button for Countersrw Enumeration .1.3.6.1.4.1.251.1.1.35.3.1.4 |
pdhE3ReconfigReconfigure linkrw Enumeration .1.3.6.1.4.1.251.1.1.35.3.1.5 |
pdhE3TxmtTimMkSet to yes(1) if traceable to primary ref clk.rw Enumeration .1.3.6.1.4.1.251.1.1.35.3.1.6 |
pdhE3PloadTypeLabPayload type label.rw Enumeration .1.3.6.1.4.1.251.1.1.35.3.1.7 |
pdhE3TxTrlTrcIdLenTrail trace length for transmit and expected receive.rw Enumeration .1.3.6.1.4.1.251.1.1.35.3.1.8 |
pdhE3TxTrcIdUHTransmit trail trace ID upper half.rw PhysAddress (SNMPv2-TC) .1.3.6.1.4.1.251.1.1.35.3.1.9 |
pdhE3TxTrcIdLHTransmit trail trace ID lower half.rw PhysAddress (SNMPv2-TC) .1.3.6.1.4.1.251.1.1.35.3.1.10 |
pdhE3RxExTrcIdUHReceive expected trail trace ID upper half.rw PhysAddress (SNMPv2-TC) .1.3.6.1.4.1.251.1.1.35.3.1.11 |
pdhE3RxExTrcIdLHReceive expected trail trace ID lower half.rw PhysAddress (SNMPv2-TC) .1.3.6.1.4.1.251.1.1.35.3.1.12 |
pdhE3FrameErrsE3 frame error countro Counter .1.3.6.1.4.1.251.1.1.35.3.1.32 |
pdhE3LcvsE3 Line Code Violation countro Counter .1.3.6.1.4.1.251.1.1.35.3.1.33 |
pdhE3ParityErrsE3-G832 parity error countro Counter .1.3.6.1.4.1.251.1.1.35.3.1.34 |
pdhE3FEBEErrsE3-G832 FEBE error countro Counter .1.3.6.1.4.1.251.1.1.35.3.1.35 |
pdhE3LOSDefectLOS Defectro Enumeration .1.3.6.1.4.1.251.1.1.35.3.1.41 |
pdhE3OOFDefectLOF Defectro Enumeration .1.3.6.1.4.1.251.1.1.35.3.1.42 |
pdhE3AISDefectAIS Defectro Enumeration .1.3.6.1.4.1.251.1.1.35.3.1.43 |
pdhE3FERFDefectFERF Defectro Enumeration .1.3.6.1.4.1.251.1.1.35.3.1.44 |
pdhE3ExBERDefectExcessive Bit Error Rate Defectro Enumeration .1.3.6.1.4.1.251.1.1.35.3.1.45 |
pdhE3LOSAlarmLOS Alarmro Enumeration .1.3.6.1.4.1.251.1.1.35.3.1.51 |
pdhE3LOFAlarmLOF Alarmro Enumeration .1.3.6.1.4.1.251.1.1.35.3.1.52 |
pdhE3AISAlarmAIS Alarmro Enumeration .1.3.6.1.4.1.251.1.1.35.3.1.53 |
pdhE3FERFAlarmFERF Alarmro Enumeration .1.3.6.1.4.1.251.1.1.35.3.1.54 |
pdhE3ExBERAlarmExcessive Bit Error Rate Alarmro Enumeration .1.3.6.1.4.1.251.1.1.35.3.1.55 |
pdhE3LESLine Errored Secondsro Counter .1.3.6.1.4.1.251.1.1.35.3.1.61 |
pdhE3LSESLine Severely Errored Secondsro Counter .1.3.6.1.4.1.251.1.1.35.3.1.62 |
pdhE3ESErrored Secondsro Counter .1.3.6.1.4.1.251.1.1.35.3.1.63 |
pdhE3SESSeverely Errored Secondsro Counter .1.3.6.1.4.1.251.1.1.35.3.1.64 |
pdhE3AISSAIS Secondsro Counter .1.3.6.1.4.1.251.1.1.35.3.1.65 |
pdhE3UASUnavailable Secondsro Counter .1.3.6.1.4.1.251.1.1.35.3.1.66 |
pdhE3RxTrlTrcLast received trail trace message.ro PhysAddress .1.3.6.1.4.1.251.1.1.35.3.1.76 |
pdhE3RxTrIdMisReceive trace id mismatch indication.ro Enumeration .1.3.6.1.4.1.251.1.1.35.3.1.77 |
pdhE3RxTrIdUnstReceive trace id unstable indication.ro Enumeration .1.3.6.1.4.1.251.1.1.35.3.1.78 |
pdhE3RxPloadTypeLabMisReceive payload type label mismatch indication.ro Enumeration .1.3.6.1.4.1.251.1.1.35.3.1.79 |
pdhE3RxPloadTypeLabUnstReceive payload type label unstable indication.ro Enumeration .1.3.6.1.4.1.251.1.1.35.3.1.80 |
dv2Oam OBJECT IDENTIFIER .1.3.6.1.4.1.251.1.1.36 |
oamTableThis table is used for per-port OAM configuration. SEQUENCE OF OamEntry .1.3.6.1.4.1.251.1.1.36.1 |
oamEntry OamEntry .1.3.6.1.4.1.251.1.1.36.1.1 |
oamLinkNoThe link number for this configuration.ro INTEGER .1.3.6.1.4.1.251.1.1.36.1.1.1 |
oamSegEndPointSet to yes(1) to configure the link as segment end point.rw Enumeration .1.3.6.1.4.1.251.1.1.36.1.1.2 |
oamVcEndPointSet to yes(1) to configure the link as connection end point.rw Enumeration .1.3.6.1.4.1.251.1.1.36.1.1.3 |
oamAisRdiGenerationSet to yes(1) to generate AIS/RDI up on physical failure.rw Enumeration .1.3.6.1.4.1.251.1.1.36.1.1.4 |
oamLastRxTypeType of the last received OAM cell.ro Enumeration .1.3.6.1.4.1.251.1.1.36.1.1.5 |
oamLastRxVpiVPI value of the last received OAM cell.ro VirtualPathIdentifier .1.3.6.1.4.1.251.1.1.36.1.1.6 |
oamLastRxVciVCI value of the last received OAM cell.ro VirtualCircuitIdentifier .1.3.6.1.4.1.251.1.1.36.1.1.7 |
oamRxCountSum of received OAM cells.ro Counter .1.3.6.1.4.1.251.1.1.36.1.1.8 |
oamLastTxTypeType of the last transmitted OAM cell.ro Enumeration .1.3.6.1.4.1.251.1.1.36.1.1.9 |
oamLastTxVpiVPI value of the last transmitted OAM cell.ro VirtualPathIdentifier .1.3.6.1.4.1.251.1.1.36.1.1.10 |
oamLastTxVciVCI value of the last transmitted OAM cell.ro VirtualCircuitIdentifier .1.3.6.1.4.1.251.1.1.36.1.1.11 |
oamTxCountSum of transmitted OAM cells.ro Counter .1.3.6.1.4.1.251.1.1.36.1.1.12 |
oamClearStatsSet to yes(2) to clear OAM Tx and Rx Statistics.rw Enumeration .1.3.6.1.4.1.251.1.1.36.1.1.13 |
oamLoopbackTableThis table is used to configure and control loopback test.
Change Test Status to Start Test(1) to initiate loopback test. SEQUENCE OF OamLoopbackEntry .1.3.6.1.4.1.251.1.1.36.2 |
oamLoopbackEntry OamLoopbackEntry .1.3.6.1.4.1.251.1.1.36.2.1 |
oamLoopbackLinkNoThe link number for this configuration.ro INTEGER .1.3.6.1.4.1.251.1.1.36.2.1.1 |
oamLoopbackVpiVPI value for the loopback cells to send.rw VirtualPathIdentifier .1.3.6.1.4.1.251.1.1.36.2.1.2 |
oamLoopbackVciVCI value for the loopback cells to send.rw VirtualCircuitIdentifier .1.3.6.1.4.1.251.1.1.36.2.1.3 |
oamLoopbackSpanFlow span for the loopback cells to send.rw Enumeration .1.3.6.1.4.1.251.1.1.36.2.1.4 |
oamLoopbackMaxNumCellsMaximum number of loopback cells to send.rw INTEGER .1.3.6.1.4.1.251.1.1.36.2.1.5 |
oamLoopbackNumCellsSentNumber of loopback cells sent.ro INTEGER .1.3.6.1.4.1.251.1.1.36.2.1.6 |
oamLoopbackTimeOutNumber of seconds to wait for loopback cells to return.rw INTEGER .1.3.6.1.4.1.251.1.1.36.2.1.7 |
oamLoopbackActiveChange to Start Test to run loopback test.rw Enumeration .1.3.6.1.4.1.251.1.1.36.2.1.8 |
oamLoopbackResultLoopback test result.ro Enumeration .1.3.6.1.4.1.251.1.1.36.2.1.9 |
oamLoopbackLocIdLocation Node ID for loopback point.rw INTEGER .1.3.6.1.4.1.251.1.1.36.2.1.10 |
oamDisableyes(2) will disable the oam for entire slot.rw Enumeration .1.3.6.1.4.1.251.1.1.36.3 |
oamVcaTableThis table is used for per-port OAM configuration. SEQUENCE OF OamVcaEntry .1.3.6.1.4.1.251.1.1.36.4 |
oamVcaEntry OamVcaEntry .1.3.6.1.4.1.251.1.1.36.4.1 |
oamVcaVpiThe VPI for this configuration.ro VirtualPathIdentifier .1.3.6.1.4.1.251.1.1.36.4.1.1 |
oamVcaVciThe VCI for this configuration.ro VirtualCircuitIdentifier .1.3.6.1.4.1.251.1.1.36.4.1.2 |
oamVcaConnectionTypeSet End point configuration on hardware per VPC/VCCrw Enumeration .1.3.6.1.4.1.251.1.1.36.4.1.3 |
oamVcaVpcEndPointSet yes(1) to configure the VC to VPC end point.rw Enumeration .1.3.6.1.4.1.251.1.1.36.4.1.4 |
oamVcaAisRdiGenerationAIS/RDI disable or enable with or without traps.rw Enumeration .1.3.6.1.4.1.251.1.1.36.4.1.5 |
oamVcaAisRdiStateAIS/RDI state for this VP/VC.ro Enumeration .1.3.6.1.4.1.251.1.1.36.4.1.6 |
oamVcaDefectTypeAIS/RDI defect type.ro Enumeration .1.3.6.1.4.1.251.1.1.36.4.1.7 |
oamVcaDefectNodeAIS/RDI location.ro INTEGER .1.3.6.1.4.1.251.1.1.36.4.1.8 |
oamVcaDefectSlotAIS/RDI location.ro INTEGER .1.3.6.1.4.1.251.1.1.36.4.1.9 |
oamVcaDefectLinkAIS/RDI location.ro INTEGER .1.3.6.1.4.1.251.1.1.36.4.1.10 |
oamVcaTrapEnableSet enable to generate trap when AIS/RDI received.rw Enumeration .1.3.6.1.4.1.251.1.1.36.4.1.11 |
oamVcaCCActivate segment or end to end Continuity Checks.rw Enumeration .1.3.6.1.4.1.251.1.1.36.4.1.12 |
oamVcaCCStateContinuity Check state.ro Enumeration .1.3.6.1.4.1.251.1.1.36.4.1.13 |
oamVcaPMActivate segment or end to end Performance Monitoring.rw Enumeration .1.3.6.1.4.1.251.1.1.36.4.1.14 |
oamVcaPMBlockSizePerformance Monitoring block size.rw Enumeration .1.3.6.1.4.1.251.1.1.36.4.1.15 |
oamVcaPMStateContinuity Check state.ro Enumeration .1.3.6.1.4.1.251.1.1.36.4.1.16 |
oamVcaBkwRptLosCellsBackward Reporting loss of cell.ro INTEGER .1.3.6.1.4.1.251.1.1.36.4.1.17 |
oamVcaBkwRptMisCellsBackward Reporting misinserted cell.ro INTEGER .1.3.6.1.4.1.251.1.1.36.4.1.18 |
oamVcaBkwRptBip16Backward Reporting BIP-16 violations.ro INTEGER .1.3.6.1.4.1.251.1.1.36.4.1.19 |
oamVcaBkwRptSevErrBackward Reporting Severly Errored Cells.ro INTEGER .1.3.6.1.4.1.251.1.1.36.4.1.20 |
oamVcbTableThis table is used for per-port OAM configuration. SEQUENCE OF OamVcbEntry .1.3.6.1.4.1.251.1.1.36.5 |
oamVcbEntry OamVcbEntry .1.3.6.1.4.1.251.1.1.36.5.1 |
oamVcbVpiThe VPI for this configuration.ro VirtualPathIdentifier .1.3.6.1.4.1.251.1.1.36.5.1.1 |
oamVcbVciThe VCI for this configuration.ro VirtualCircuitIdentifier .1.3.6.1.4.1.251.1.1.36.5.1.2 |
oamVcbConnectionTypeSet End point configuration on hardware per VPC/VCCrw Enumeration .1.3.6.1.4.1.251.1.1.36.5.1.3 |
oamVcbVpcEndPointSet yes(1) to configure the VC to VPC end point.rw Enumeration .1.3.6.1.4.1.251.1.1.36.5.1.4 |
oamVcbAisRdiGenerationAIS/RDI disable or enable with or without traps.rw Enumeration .1.3.6.1.4.1.251.1.1.36.5.1.5 |
oamVcbAisRdiStateAIS/RDI state for this VP/VC.ro Enumeration .1.3.6.1.4.1.251.1.1.36.5.1.6 |
oamVcbDefectTypeAIS/RDI defect type.ro Enumeration .1.3.6.1.4.1.251.1.1.36.5.1.7 |
oamVcbDefectNodeAIS/RDI location.ro INTEGER .1.3.6.1.4.1.251.1.1.36.5.1.8 |
oamVcbDefectSlotAIS/RDI location.ro INTEGER .1.3.6.1.4.1.251.1.1.36.5.1.9 |
oamVcbDefectLinkAIS/RDI location.ro INTEGER .1.3.6.1.4.1.251.1.1.36.5.1.10 |
oamVcbTrapEnableSet enable to generate trap when AIS/RDI received.rw Enumeration .1.3.6.1.4.1.251.1.1.36.5.1.11 |
oamVcbCCActivate segment or end to end Continuity Checks.rw Enumeration .1.3.6.1.4.1.251.1.1.36.5.1.12 |
oamVcbCCStateContinuity Check state.ro Enumeration .1.3.6.1.4.1.251.1.1.36.5.1.13 |
oamVcbPMActivate segment or end to end Performance Monitoring.rw Enumeration .1.3.6.1.4.1.251.1.1.36.5.1.14 |
oamVcbPMBlockSizePerformance Monitoring block size.rw Enumeration .1.3.6.1.4.1.251.1.1.36.5.1.15 |
oamVcbPMStateContinuity Check state.ro Enumeration .1.3.6.1.4.1.251.1.1.36.5.1.16 |
oamVcbBkwRptLosCellsBackward Reporting loss of cell.ro INTEGER .1.3.6.1.4.1.251.1.1.36.5.1.17 |
oamVcbBkwRptMisCellsBackward Reporting misinserted cell.ro INTEGER .1.3.6.1.4.1.251.1.1.36.5.1.18 |
oamVcbBkwRptBip16Backward Reporting BIP-16 violations.ro INTEGER .1.3.6.1.4.1.251.1.1.36.5.1.19 |
oamVcbBkwRptSevErrBackward Reporting Severly Errored Cells.ro INTEGER .1.3.6.1.4.1.251.1.1.36.5.1.20 |
dv2Lmi OBJECT IDENTIFIER .1.3.6.1.4.1.251.1.1.37 |
lmiTableThis table is used to control ILMI configuration. SEQUENCE OF LmiEntry .1.3.6.1.4.1.251.1.1.37.1 |
lmiEntry LmiEntry .1.3.6.1.4.1.251.1.1.37.1.1 |
lmiLinkNoThe link number for this configuration.ro INTEGER .1.3.6.1.4.1.251.1.1.37.1.1.1 |
lmiVpiThe VPI used for ILMI.rw VirtualPathIdentifier .1.3.6.1.4.1.251.1.1.37.1.1.2 |
lmiVciThe VCI used for ILMI.rw VirtualCircuitIdentifier .1.3.6.1.4.1.251.1.1.37.1.1.3 |
lmiTypeSet to network side (1) to configure the link as network side ILMI.rw Enumeration .1.3.6.1.4.1.251.1.1.37.1.1.4 |
lmiStateThe state of ILMI for this link.ro Enumeration .1.3.6.1.4.1.251.1.1.37.1.1.5 |
lmiFormatILMI address format.rw Enumeration .1.3.6.1.4.1.251.1.1.37.1.1.6 |
lmiPrefixDefault Network prefix to use.ro E164SUB .1.3.6.1.4.1.251.1.1.37.1.1.7 |
lmiOnOffTurn on/off ILMI.rw Enumeration .1.3.6.1.4.1.251.1.1.37.1.1.8 |
lmiPollPeriodPeriod in seconds to send polling request for link management.rw INTEGER .1.3.6.1.4.1.251.1.1.37.1.1.9 |
lmiNoRspDownNumber of failed polls (no response) before declaration of link down.rw INTEGER .1.3.6.1.4.1.251.1.1.37.1.1.10 |
lmiLinkMgmtTurn on/off link management.rw Enumeration .1.3.6.1.4.1.251.1.1.37.1.1.11 |
lmiConnectivityATM interface status.ro Enumeration .1.3.6.1.4.1.251.1.1.37.1.1.12 |
lmiPrefixModModifiable Network prefix to use. MUST BE 26 DIGITSrw E164 .1.3.6.1.4.1.251.1.1.37.1.1.13 |
lmiEsiESI field to use on User side. MUST BE 12 DIGITSrw E164 .1.3.6.1.4.1.251.1.1.37.1.1.14 |
lmiNetSideTableThis table is used to configure and control network side ILMI. SEQUENCE OF LmiNetSideEntry .1.3.6.1.4.1.251.1.1.37.2 |
lmiNetSideEntry LmiNetSideEntry .1.3.6.1.4.1.251.1.1.37.2.1 |
lmiNetSideLinkNoThe link number for this configuration.ro INTEGER .1.3.6.1.4.1.251.1.1.37.2.1.1 |
lmiNetSidePrefixIdNetwork prefix identification number.ro INTEGER .1.3.6.1.4.1.251.1.1.37.2.1.2 |
lmiNetSidePrefixNetwork prefix to register or de-register.ro E164SUB .1.3.6.1.4.1.251.1.1.37.2.1.3 |
lmiNetSidePrefixStatusSet to register to send the prefix to the user side;
set to de-register to remove the prefix from the user side.ro Enumeration .1.3.6.1.4.1.251.1.1.37.2.1.4 |
lmiUserSideTableThis table is used to configure and control user side ILMI. SEQUENCE OF LmiUserSideEntry .1.3.6.1.4.1.251.1.1.37.3 |
lmiUserSideEntry LmiUserSideEntry .1.3.6.1.4.1.251.1.1.37.3.1 |
lmiUserSideLinkNoThe link number for this configuration.ro INTEGER .1.3.6.1.4.1.251.1.1.37.3.1.1 |
lmiUserSideAddressIdThe link number for this configuration.ro INTEGER .1.3.6.1.4.1.251.1.1.37.3.1.2 |
lmiUserSideAddressATM address to register or de-register.ro E164SUB .1.3.6.1.4.1.251.1.1.37.3.1.3 |
lmiUserSideAddressStatusSet to valid to register the address to the network side;
set to invalid to de-register the address from the network side.ro Enumeration .1.3.6.1.4.1.251.1.1.37.3.1.4 |
dv2AlarmHandler OBJECT IDENTIFIER .1.3.6.1.4.1.251.1.1.38 |
alarmNodeCritNode Critical Alarm Statusro Enumeration .1.3.6.1.4.1.251.1.1.38.1 |
alarmNodeMajorNode Major Alarm Statusro Enumeration .1.3.6.1.4.1.251.1.1.38.2 |
alarmNodeMinorNode Minor Alarm Statusro Enumeration .1.3.6.1.4.1.251.1.1.38.3 |
alarmStatTableThis table is used for Alarm Handler status SEQUENCE OF AlarmStatEntry .1.3.6.1.4.1.251.1.1.38.4 |
alarmStatEntry AlarmStatEntry .1.3.6.1.4.1.251.1.1.38.4.1 |
alrStatSlotNoSlot Numberro INTEGER .1.3.6.1.4.1.251.1.1.38.4.1.1 |
slotCritStatusSlot Critical Alarm Statusro Enumeration .1.3.6.1.4.1.251.1.1.38.4.1.2 |
slotMajorStatusSlot Major Alarm Statusro Enumeration .1.3.6.1.4.1.251.1.1.38.4.1.3 |
slotMinorStatusSlot Minor Alarm Statusro Enumeration .1.3.6.1.4.1.251.1.1.38.4.1.4 |
link0CritStatusLink 0 Critical Alarm Statusro Enumeration .1.3.6.1.4.1.251.1.1.38.4.1.5 |
link0MajorStatusLink 0 Major Alarm Statusro Enumeration .1.3.6.1.4.1.251.1.1.38.4.1.6 |
link0MinorStatusLink 0 Minor Alarm Statusro Enumeration .1.3.6.1.4.1.251.1.1.38.4.1.7 |
link1CritStatusLink 1 Critical Alarm Statusro Enumeration .1.3.6.1.4.1.251.1.1.38.4.1.8 |
link1MajorStatusLink 1 Major Alarm Statusro Enumeration .1.3.6.1.4.1.251.1.1.38.4.1.9 |
link1MinorStatusLink 1 Minor Alarm Statusro Enumeration .1.3.6.1.4.1.251.1.1.38.4.1.10 |
link2CritStatusLink 2 Critical Alarm Statusro Enumeration .1.3.6.1.4.1.251.1.1.38.4.1.11 |
link2MajorStatusLink 2 Major Alarm Statusro Enumeration .1.3.6.1.4.1.251.1.1.38.4.1.12 |
link2MinorStatusLink 2 Minor Alarm Statusro Enumeration .1.3.6.1.4.1.251.1.1.38.4.1.13 |
link3CritStatusLink 3 Critical Alarm Statusro Enumeration .1.3.6.1.4.1.251.1.1.38.4.1.14 |
link3MajorStatusLink 3 Major Alarm Statusro Enumeration .1.3.6.1.4.1.251.1.1.38.4.1.15 |
link3MinorStatusLink 3 Minor Alarm Statusro Enumeration .1.3.6.1.4.1.251.1.1.38.4.1.16 |
alarmNodeACONode ACO Statusrw Enumeration .1.3.6.1.4.1.251.1.1.38.5 |
alarmACOTableThis table is used for the Alarm Handler ACO SEQUENCE OF AlarmACOEntry .1.3.6.1.4.1.251.1.1.38.6 |
alarmACOEntry AlarmACOEntry .1.3.6.1.4.1.251.1.1.38.6.1 |
alrACOslotNoSlot Numberro INTEGER .1.3.6.1.4.1.251.1.1.38.6.1.1 |
alrACOslotACOSlot ACO Statusrw Enumeration .1.3.6.1.4.1.251.1.1.38.6.1.2 |
alrACOlink0ACOLink 0 ACO Statusrw Enumeration .1.3.6.1.4.1.251.1.1.38.6.1.3 |
alrACOlink1ACOLink 1 ACO Statusrw Enumeration .1.3.6.1.4.1.251.1.1.38.6.1.4 |
alrACOlink2ACOLink 2 ACO Statusrw Enumeration .1.3.6.1.4.1.251.1.1.38.6.1.5 |
alrACOlink3ACOLink 3 ACO Statusrw Enumeration .1.3.6.1.4.1.251.1.1.38.6.1.6 |
userStatusTableThis table is used for the User Status Inputs SEQUENCE OF UserStatusEntry .1.3.6.1.4.1.251.1.1.38.7 |
userStatusEntry UserStatusEntry .1.3.6.1.4.1.251.1.1.38.7.1 |
userInputNoUser Status Input Numberro INTEGER .1.3.6.1.4.1.251.1.1.38.7.1.1 |
userInputEnableEnable User Status Inputrw Enumeration .1.3.6.1.4.1.251.1.1.38.7.1.2 |
userInputTrapEnableEnable User Defined Trap/Eventrw Enumeration .1.3.6.1.4.1.251.1.1.38.7.1.3 |
userInputTrapDescDescription string for trap/eventrw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.251.1.1.38.7.1.4 |
userInputActiveStateAlarm active state of user input relay switchrw Enumeration .1.3.6.1.4.1.251.1.1.38.7.1.5 |
userInputAlrClassClassification of Status/Alarm Inputro Enumeration .1.3.6.1.4.1.251.1.1.38.7.1.10 |
userInputStatusCurrent Status of Status/Alarm Inputro Enumeration .1.3.6.1.4.1.251.1.1.38.7.1.11 |
alarmScanFileRescan the alr_class.txt filerw Enumeration .1.3.6.1.4.1.251.1.1.38.8 |
dv2Cac OBJECT IDENTIFIER .1.3.6.1.4.1.251.1.1.39 |
cacCurrentEbtIdCurrent EBT file ID code.
<DETAIL_DESCRIPTION>
cacCurrentEbtId holds the EBT file ID code of the EBT file
currently in memory in a verified state. The CAC application
is responsible for maintaining the state of this variable.
If there is a verified EBT in memory cacCurrentEbtId will
still hold the EBT file's ID code even if the CAC is disabled
or the CAC version is scr-pcr. If there is no EBT in memory
or the verification was unsuccessful then the value of
cacCurrentEbtId is zero (0).ro INTEGER .1.3.6.1.4.1.251.1.1.39.1 |
cacEbtCommandEBT file command.
<DETAIL_DESCRIPTION>
This field, normally with the value none, may be set by the
manager to: * load-ebt to initiate the loading of a new EBT
file into memory.
* dump-ebt to initiate the dump of the EBT memory
content into flash.
* delete-ebt to cause an EBT file to be deleted
in the flash.
The value of cacEbtCommand will return to none when the EBT
file command has been completed.rw Enumeration .1.3.6.1.4.1.251.1.1.39.2 |
cacCommandEbtIdCommand EBT file ID code.
<DETAIL_DESCRIPTION>
cacCommandEbtId is written to by the manager to identify the
EBT file in the flash that should be loaded or deleted. When
the cacEbtCommand MIB item is set to either load-ebt or
delete-ebt, the CAC software attempts to load or delete the
EBT file named ebXXXXX.bin from flash, where XXXXX is the
value cacCommandEbtId padded to five digits with leading zeros.
The value zero (0) is not a valid EBT file ID code and is
reserved to indicate that EBT file ID code has not been specified.rw INTEGER .1.3.6.1.4.1.251.1.1.39.3 |
cacEbtStateState of the CAC.
<DETAIL_DESCRIPTION>
The state: * uninitialized is an initial MIB value which is never
returned to without starting from a new MIB.
* initializing indicates the initial part of the CAC boot.
* loading indicates that an EBT file is being loaded.
* ready indicates that a valid EBT is in memory. In
this state the current EBT file ID code shows the ID
code of the EBT in memory.
* unusable is reached after an unsuccessful load and
indicates that the data in the EBT memory block is
unusable (in this state current EBT file ID code shows 0).ro Enumeration .1.3.6.1.4.1.251.1.1.39.4 |
cacErrorCodeError code.
<DETAIL_DESCRIPTION>
Error codes are produced at certain stages in the CAC application.
The interpretation of the error codes is:
Terms: 'ebXXXXX.bin' : binary file in flash
data structure: EBT_file_template based structure
* no-error: no error encountered.
* nonexistent-file: the 'ebXXXXX.bin' file not found in the flash,
during APEX boot or MIB EBT load request.
* bad-file-length: mismatch in file length specified within
'ebXXXXX.bin' and the pre-specified file length. Occurs while
loading file into data structures.
* copy-corrupted: copying of data from 'ebXXXXX.bin' into the data
structure, EBT_file_template did not proceed smoothly and the data
structure is now corrupted.
* nunused-cbtdwoEBTid: command EBT id not used and current EBT id
is 0. The CAC booted without valid EBT values in the data structure.
Occurs during boot while loading file into data structures.
* nunused-cinvalid: command EBT id not used. The file eb'current EBT
id'.bin contains invalid data. Occurs just after the EBT file got
loaded into the data structure, when the verification of values
in the data structure takes place.
* nEBTid-uninit-cstays: command EBT id is 0 and the data structures
remain unchanged. Occurs when mib item cacTableload is switched to yes.
* ninvalid-cstays: eb'command EBT id'.bin contains invalid data and
the data structures remain unchanged. Occurs when mib item cacTableload
is switched to yes.
* ninvalid-cEBTid-uninit: eb'command EBT id'.bin contains invalid data
and the current EBT id is zero. This means that data structure is
corrupted. Occurs when mib item cacTableload is switched to yes.
* ninvalid-cinvalid: both eb'command EBT id'.bin and eb'current EBT
id'.bin contains invalid data. The data structure is corrupted.
Occurs when mib item cacTableload is switched to yes.
* ninvalid-cnoerror: eb'command EBT id'.bin contains invalid data
and the eb'current EBT id'.bin is loaded successfully. Occurs
when mib item cacTableload is switched to yes.
* link-not-ready: it is a runtime error which states that link is
not ready for configuration.
* link-not-configuring: it is a runtime error which states that link
is not in configuring mode and therefore the recalculation of EBT
or scr-pcr sums is not possible.
* EBT-not-loaded: it is a runtime error which states that the data
structure does not contain valid data. This occurs when the EBT
enable mib switch is turned to 'yes' or the cac version mib item
is switched to EBT.
* class-not-found: this runtime error indicates that during the
processing of allocate, deallocate or change functions, a class
corresponding to SCR, PCR or MBS was not found. The effective
bandwidth used in this situation is the same as a CBR allocation
using the attempted connection's PCR.
* dump-fs-error: this error indicates that a file system error
(e.g. the file system became full) during the EBT file dump function.
The dump file was deleted after the file system error was detected.ro Enumeration .1.3.6.1.4.1.251.1.1.39.5 |
cacPerLinkTableThis table containing per link data.
<DETAIL_DESCRIPTION>
Contains per link specific data SEQUENCE OF CacPerLinkEntry .1.3.6.1.4.1.251.1.1.39.6 |
cacPerLinkEntry CacPerLinkEntry .1.3.6.1.4.1.251.1.1.39.6.1 |
cacLinkNoLink number.
<DETAIL_DESCRIPTION>
cacLinkNo is the index (0..3) to the array of link data.ro INTEGER .1.3.6.1.4.1.251.1.1.39.6.1.1 |
cacLinkSumE10Running sum of e10.
<DETAIL_DESCRIPTION>
cacSumE10 zero loss effective bandwidth for high priority queue.
This value is maintained only when the CAC is enabled on the link
(cacEnable) and when the EBT CAC version is being used
(cacVersion==EBT) otherwise the values here are zero.ro Gauge .1.3.6.1.4.1.251.1.1.39.6.1.2 |
cacLinkSumE1TRunning sum of e1T.
<DETAIL_DESCRIPTION>
cacSumE1T tangent effective bandwidth for high priority queue.
This value is maintained only when the CAC is enabled on the link
(cacEnable) and when the EBT CAC version is being used
(cacVersion==EBT) otherwise the values here are zero.ro Gauge .1.3.6.1.4.1.251.1.1.39.6.1.3 |
cacLinkObfPvc1Utilization factor for high priority pvc.
<DETAIL_DESCRIPTION>
Utilization factor for PVCs and SPVCs for the high priority queue.rw INTEGER .1.3.6.1.4.1.251.1.1.39.6.1.4 |
cacLinkObfSvc1Utilization factor for high priority svc.
<DETAIL_DESCRIPTION>
Utilization factor for SVCs for the high priority queue.rw INTEGER .1.3.6.1.4.1.251.1.1.39.6.1.5 |
cacLinkSumE20Running sum of e20.
<DETAIL_DESCRIPTION>
cacSumE20 zero loss effective bandwidth for low priority queue.
This value is maintained only when the CAC is enabled on the link
(cacEnable) and when the EBT CAC version is being used
(cacVersion==EBT) otherwise the values here are zero.ro Gauge .1.3.6.1.4.1.251.1.1.39.6.1.6 |
cacLinkSumE2TRunning sum of e2T.
<DETAIL_DESCRIPTION>
cacSumE1T zero tangent effective bandwidth for low priority queue.
This value is maintained only when the CAC is enabled on the link
(cacEnable) and when the EBT CAC version is being used
(cacVersion==EBT) otherwise the values here are zero.ro Gauge .1.3.6.1.4.1.251.1.1.39.6.1.7 |
cacLinkObfPvc2Utilization factor for low priority pvc.
<DETAIL_DESCRIPTION>
Utilization factor for PVCs and SPVCs for the low priority queue.rw INTEGER .1.3.6.1.4.1.251.1.1.39.6.1.8 |
cacLinkObfSvc2Utilization factor for low priority svc.
<DETAIL_DESCRIPTION>
Utilization factor for SVCs for the low priority queue.rw INTEGER .1.3.6.1.4.1.251.1.1.39.6.1.9 |
cacLinkTotalBwScrPcrtotal bw allocation on the link by scr-pcr CAC.
<DETAIL_DESCRIPTION>
cacTotalBwScrPcr is the total bandwidth allocated to extant connections
when the CAC is enabled and when the SCR-PCR CAC is being used.
Its value is zero if CAC is disabled or the EBT CAC mode is used.ro INTEGER .1.3.6.1.4.1.251.1.1.39.6.1.10 |
cacCurrentLinkUsageCurrent link bandwidth allocation.
<DETAIL_DESCRIPTION>
It is the current indication of bandwidth allocation on a link based
on the formula using effective bandwidthsro INTEGER .1.3.6.1.4.1.251.1.1.39.6.1.11 |
cacMaxLinkUsageMax link bw allocation since last reset or card boot.
<DETAIL_DESCRIPTION>
cacMaxLinkUsage shows the maximum value that cacCurrentLinkUsage
has reached since cacMaxLinkUsage was last reset.ro INTEGER .1.3.6.1.4.1.251.1.1.39.6.1.12 |
cacLinkResetReload maximum link usage from current allocation.
<DETAIL_DESCRIPTION>
cacReset resets cacMaxLinkUsage, after the reset cacMaxLinkUsage
shows the same value as cacCurrentLinkUsage.rw Enumeration .1.3.6.1.4.1.251.1.1.39.6.1.13 |
cacLinkVersionUse EB CAC or scr-pcr CAC?
<DETAIL_DESCRIPTION>
The per-link variable cacVersion may take on the values
* SCR-PCR indicating that the old, pre Rel 4.2 CAC based on SCR
and PCR values, is in operation or
* EBT indicating that the new CAC based on effective bandwidths is used.
cacVersion may be set by the manager.
If cacVersion is set to EBT by the manager it will revert to SCR-PCR
unless a valid EBT is currently available in memory
(in which case cacEbtState==ready and cacCurrentEbtId holds a non-zero value).
The cacVersion may also revert to SCR-PCR if, during boot or an EBT load,
a valid EBT cannot be established in memory.
A change of state in cacVersion will result in recalculatation of EB Sums.rw Enumeration .1.3.6.1.4.1.251.1.1.39.6.1.14 |
cacLinkEnableEnable cac?
<DETAIL_DESCRIPTION>
When cacEnable has the value
* yes, then the three CAC service routines are operational as defined,
* no, then all connections are accepted regardless of required bandwidths
CAC may be enabled or disabled by the manager at any time that the
cacLinkState is ready. Enabling CAC will cause recalculatation of
EB sums for that link. Disabling CAC will cause the EB sums for
the link (also for associated V-SAPs) to be set to zero.rw Enumeration .1.3.6.1.4.1.251.1.1.39.6.1.15 |
cacLinkSignalModeLink signalling mode
<DETAIL_DESCRIPTION>
cacSignallingMode is a read-only variable indicating whether the link
is currently in the signalling mode:
* single-channel or
* multi-channel
The value of cacSignallingMode is updated any time a virtual SAP is
either associated or disassociated with a physical SAP. Multi-channel
mode indicates that at least one virtual SAP is associated with the
link's physical SAP. In multi-channel mode the zero-loss effective
bandwidths are not used for connection admission control.ro Enumeration .1.3.6.1.4.1.251.1.1.39.6.1.16 |
cacLinkStateState of the Link
<DETAIL_DESCRIPTION>
The cacLinkState variable can take the values:
* uninitialised is an initial MIB value which is never returned to
without staring from a new MIB.
* configuring indicates that the CAC on that link cannot be used at
the current time. This indicates that CAC is booting, an EBT is
being loaded. This is a transient state that will go to ready or
recalculating.
* recalculating indicates that the sums for both eb and scr-pcr
are cleared and are recalculated for the existing connections.
* ready indicates that CAC may be used on that link.
The state machine is given in Figure3. Transitions out of the
ready state can be caused by a boot, an EBT load or the call back
functions on (per link) Enable and Version. Whether the transition
from configuring back to ready is direct or via recalculating depends
on whether or not there is a need to recalculate the effective bandwidth
sums; this depends on several factors that can be derived from the
detailed design in Section6.2.4.7.
The value of the cacLinkState variable is valid and indicates the
current link state of the CAC indepenently of the value of cacEnable,
cacVersion and cacEbtState.
When cacLinkState is configuring, certain CAC functions are disabled:
* Requests to the allocate, deallocate and allocation_change service
routines will be rejected without processing.
* Requests to the allocation summary routine may produce inconsistent results.
When cacLinkState is recalculating, certain CAC functions are disabled:
* Requests to allocation_change and deallocate service routines will
be rejected without processing.
* Requests to the allocation summary routine may produce inconsistent results.ro Enumeration .1.3.6.1.4.1.251.1.1.39.6.1.17 |
cacPerSapTableThis table containing per Sap data.
<DETAIL_DESCRIPTION>
The virtual SAP table in the MIB has 12 entries indexed by cacSapNo
in the range (20..31). For each SAP there the table entries are detailed below.
These entries are only used when at least one of the link's cacSignallingMode
is multi-channel. The association of a virtual SAP to a link is given in
the resource table MIB group. SEQUENCE OF CacPerSapEntry .1.3.6.1.4.1.251.1.1.39.7 |
cacPerSapEntry CacPerSapEntry .1.3.6.1.4.1.251.1.1.39.7.1 |
cacSapNoSAP number.
<DETAIL_DESCRIPTION>
cacSapNo is the index (0..11) to the array of sap data.ro INTEGER .1.3.6.1.4.1.251.1.1.39.7.1.1 |
cacSapSumE1TRunning sum of e1T.
<DETAIL_DESCRIPTION>
cacSumE1T tangent effective bandwidth for high priority queue
These values are maintained only when the CAC is enabled on the link
(cacEnable), when the SAP is assigned to a link and when the EBT CAC
version is being used (cacVersion==EBT) otherwise the values here are zero.ro Gauge .1.3.6.1.4.1.251.1.1.39.7.1.2 |
cacSapSumE2TRunning sum of e2T.
<DETAIL_DESCRIPTION>
cacSumE1T tangent effective bandwidth for low priority queue
These values are maintained only when the CAC is enabled on the link
(cacEnable), when the SAP is assigned to a link and when the EBT CAC version
is being used (cacVersion==EBT) otherwise the values here are zero.ro Gauge .1.3.6.1.4.1.251.1.1.39.7.1.3 |
cacSapTotalBwScrPcrtotal bw allocation on the link by scr-pcr CAC.
<DETAIL_DESCRIPTION>
cacTotalBwScrPcr is the total bandwidth allocated to extant connections
when the CAC is enabled and when the SCR-PCR CAC is being used. Its value
is zero if CAC is disabled or the EBT CAC mode is used.ro INTEGER .1.3.6.1.4.1.251.1.1.39.7.1.4 |
cacCurrentSapUsageCurrent SAP bandwidth allocation
<DETAIL_DESCRIPTION>
It is the current indication of bandwidth allocation on a sap based on
the formula using effective bandwidths.ro INTEGER .1.3.6.1.4.1.251.1.1.39.7.1.5 |
cacMaxSapUsageMax SAP b/w allocation since last reset or card boot.
<DETAIL_DESCRIPTION>
cacMaxSapUsage shows the maximum value that cacCurrentSapUsage has
reached since cacMaxSapUsage was last reset.ro INTEGER .1.3.6.1.4.1.251.1.1.39.7.1.6 |
cacSapResetReload maximum SAP usage from current allocation
<DETAIL_DESCRIPTION>
cacReset resets cacMaxSapUsage, after the reset cacMaxSapUsage
shows the same value as cacCurrentSapUsage.rw Enumeration .1.3.6.1.4.1.251.1.1.39.7.1.7 |
dv2MS2FRAC OBJECT IDENTIFIER .1.3.6.1.4.1.251.1.1.40 |
dv2aal5 OBJECT IDENTIFIER .1.3.6.1.4.1.251.1.1.41 |
vhsystem OBJECT IDENTIFIER .1.3.6.1.4.1.251.1.1.42 |
limHostRevHost S/W Revisionro DisplayString .1.3.6.1.4.1.251.1.1.42.1 |
limBootRevBoot S/W Revisionro DisplayString .1.3.6.1.4.1.251.1.1.42.2 |
limHwRevHardware Architecturero DisplayString .1.3.6.1.4.1.251.1.1.42.3 |
limActionLIM actionrw Enumeration .1.3.6.1.4.1.251.1.1.42.4 |
limStateLIM statero Enumeration .1.3.6.1.4.1.251.1.1.42.5 |
limFaultLIM Fault LEDro Enumeration .1.3.6.1.4.1.251.1.1.42.6 |
limFaultReasonLIM Fault Reasonro Enumeration .1.3.6.1.4.1.251.1.1.42.7 |
limCodec0H.320 Codec 0 Active LEDro Enumeration .1.3.6.1.4.1.251.1.1.42.8 |
limCodec1H.320 Codec 1 Active LEDro Enumeration .1.3.6.1.4.1.251.1.1.42.9 |
limSCmgmtSlot Controller Mgmt Link Statusro Enumeration .1.3.6.1.4.1.251.1.1.42.10 |
limSCmgmtDataSlot Controller Mgmt Information Data Statero Enumeration .1.3.6.1.4.1.251.1.1.42.11 |
limSCfileXferReqSlot Controller Mgmt File Transfer Requestrw Enumeration .1.3.6.1.4.1.251.1.1.42.12 |
limSCfileXferStatSlot Controller Mgmt File Transfer Statero Enumeration .1.3.6.1.4.1.251.1.1.42.13 |
limSCbytesSlot Controller Mgmt File Transfer Byte Countro INTEGER .1.3.6.1.4.1.251.1.1.42.14 |
vhcontrol OBJECT IDENTIFIER .1.3.6.1.4.1.251.1.1.43 |
ctrlTable SEQUENCE OF CtrlEntry .1.3.6.1.4.1.251.1.1.43.1 |
ctrlEntry CtrlEntry .1.3.6.1.4.1.251.1.1.43.1.1 |
ctrlIndexCodec Indexro INTEGER .1.3.6.1.4.1.251.1.1.43.1.1.1 |
ctrlCodecTypeCodec Typero Enumeration .1.3.6.1.4.1.251.1.1.43.1.1.2 |
ctrlCodecActionCodec Actionrw Enumeration .1.3.6.1.4.1.251.1.1.43.1.1.3 |
ctrlCodecReqCodec Requestrw Enumeration .1.3.6.1.4.1.251.1.1.43.1.1.4 |
ctrlCallTypeCodec Call Typero Enumeration .1.3.6.1.4.1.251.1.1.43.1.1.5 |
ctrlCodecStaCodec Statusro Enumeration .1.3.6.1.4.1.251.1.1.43.1.1.6 |
ctrlChnlLpbkCodec Channel Loopbackrw Enumeration .1.3.6.1.4.1.251.1.1.43.1.1.7 |
ctrlFramingCodec H.221 Framing Detectedro Enumeration .1.3.6.1.4.1.251.1.1.43.1.1.8 |
ctrlChnlStatCodec Channel Link Statusro Enumeration .1.3.6.1.4.1.251.1.1.43.1.1.9 |
ctrlFaultReasonCodec Fault Reasonro Enumeration .1.3.6.1.4.1.251.1.1.43.1.1.10 |
vidTable SEQUENCE OF VidEntry .1.3.6.1.4.1.251.1.1.43.2 |
vidEntry VidEntry .1.3.6.1.4.1.251.1.1.43.2.1 |
vidIndexVH320 Codec Indexro INTEGER .1.3.6.1.4.1.251.1.1.43.2.1.1 |
vidStandardVH320 Analog Video I/O Standardrw Enumeration .1.3.6.1.4.1.251.1.1.43.2.1.2 |
vidTxVidReqVH320 Transmit Video Requestrw Enumeration .1.3.6.1.4.1.251.1.1.43.2.1.3 |
vidRxVidReqVH320 Display Video Requestrw Enumeration .1.3.6.1.4.1.251.1.1.43.2.1.4 |
vidViewPipVH320 View Self Picture in Picturerw Enumeration .1.3.6.1.4.1.251.1.1.43.2.1.5 |
vidCompQualVH320 Compression Qualityrw Enumeration .1.3.6.1.4.1.251.1.1.43.2.1.6 |
vidDigLpbkVH320 Digital Loopbackrw Enumeration .1.3.6.1.4.1.251.1.1.43.2.1.7 |
vidEncFrameCountVH320 Video Encoded Frame Countro Counter .1.3.6.1.4.1.251.1.1.43.2.1.8 |
vidDecFrameCountVH320 Video Decoded Frame Countro Counter .1.3.6.1.4.1.251.1.1.43.2.1.9 |
vidStateVH320 Video Statero Enumeration .1.3.6.1.4.1.251.1.1.43.2.1.10 |
vidInPresentVH320 Video Input Presentro Enumeration .1.3.6.1.4.1.251.1.1.43.2.1.11 |
vidEncBitRateVH320 Encoded Bitrate (bps)ro INTEGER .1.3.6.1.4.1.251.1.1.43.2.1.12 |
audTable SEQUENCE OF AudEntry .1.3.6.1.4.1.251.1.1.43.3 |
audEntry AudEntry .1.3.6.1.4.1.251.1.1.43.3.1 |
audIndexVH320 Codec Indexro INTEGER .1.3.6.1.4.1.251.1.1.43.3.1.1 |
audStateVH320 Audio Statero Enumeration .1.3.6.1.4.1.251.1.1.43.3.1.2 |
audPrefModeVH320 Audio Preferred Coding Moderw Enumeration .1.3.6.1.4.1.251.1.1.43.3.1.3 |
audCommModeVH320 Audio Common Coding Modero Enumeration .1.3.6.1.4.1.251.1.1.43.3.1.4 |
audBitRateVH320 Audio Bit Rate (bps)ro INTEGER .1.3.6.1.4.1.251.1.1.43.3.1.5 |
audMuteInReqVH320 Audio Mute Input Requestrw Enumeration .1.3.6.1.4.1.251.1.1.43.3.1.6 |
audMuteOutReqVH320 Audio Mute Output Requestrw Enumeration .1.3.6.1.4.1.251.1.1.43.3.1.7 |
audMuteOutStatVH320 Audio Mute Output Statusro Enumeration .1.3.6.1.4.1.251.1.1.43.3.1.8 |
audLpbkVH320 Audio Loopback Requestrw Enumeration .1.3.6.1.4.1.251.1.1.43.3.1.9 |
audInVolVH320 Audio Input Volumerw INTEGER .1.3.6.1.4.1.251.1.1.43.3.1.10 |
audOutVolVH320 Audio Output Volumerw INTEGER .1.3.6.1.4.1.251.1.1.43.3.1.11 |
audInDelayVH320 Audio Input Delay Request (ms)rw INTEGER .1.3.6.1.4.1.251.1.1.43.3.1.12 |
audOutDelayVH320 Audio Output Delay Status (ms)rw INTEGER .1.3.6.1.4.1.251.1.1.43.3.1.13 |
audFaultReasonVH320 Audio Fault Reasonro Enumeration .1.3.6.1.4.1.251.1.1.43.3.1.14 |
dataTable SEQUENCE OF DataEntry .1.3.6.1.4.1.251.1.1.43.4 |
dataEntry DataEntry .1.3.6.1.4.1.251.1.1.43.4.1 |
dataIndexVH320 Codec Indexro INTEGER .1.3.6.1.4.1.251.1.1.43.4.1.1 |
dataChnlTypeData Channel Typerw Enumeration .1.3.6.1.4.1.251.1.1.43.4.1.2 |
dataPortSpeedData Port Speed (bps)rw Enumeration .1.3.6.1.4.1.251.1.1.43.4.1.3 |
dataPortProtData Port Protocolrw Enumeration .1.3.6.1.4.1.251.1.1.43.4.1.4 |
dataHDLCcheckHDLC Check CRCrw Enumeration .1.3.6.1.4.1.251.1.1.43.4.1.5 |
dataChnlStatData Channel Statusro Enumeration .1.3.6.1.4.1.251.1.1.43.4.1.6 |
dataBytesRcvdData Channel Bytes Receivedro Counter .1.3.6.1.4.1.251.1.1.43.4.1.7 |
dataBytesSentData Channel Bytes Sentro Counter .1.3.6.1.4.1.251.1.1.43.4.1.8 |
dataResetStatData Channel Reset Statisticsrw Enumeration .1.3.6.1.4.1.251.1.1.43.4.1.9 |
vhmgmt OBJECT IDENTIFIER .1.3.6.1.4.1.251.1.1.44 |
mgmtTable SEQUENCE OF MgmtEntry .1.3.6.1.4.1.251.1.1.44.1 |
mgmtEntry MgmtEntry .1.3.6.1.4.1.251.1.1.44.1.1 |
mgmtIndexVH320 Management Port Indexro INTEGER .1.3.6.1.4.1.251.1.1.44.1.1.1 |
mgmtDescrVH320 Management Port Descriptorro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.251.1.1.44.1.1.2 |
mgmtPortProtManagement Port Protocolrw Enumeration .1.3.6.1.4.1.251.1.1.44.1.1.3 |
mgmtPortSpeedManagement Port Speed (bps)rw Enumeration .1.3.6.1.4.1.251.1.1.44.1.1.4 |
mgmtPortAddressManagement Port Addressrw IpAddress .1.3.6.1.4.1.251.1.1.44.1.1.5 |
mgmtAddressMaskManagement Port Address Maskrw IpAddress .1.3.6.1.4.1.251.1.1.44.1.1.6 |
mgmtRemoteAddressManagement Remote Addressrw IpAddress .1.3.6.1.4.1.251.1.1.44.1.1.7 |
mgmtPortStatManagement Port Statusro Enumeration .1.3.6.1.4.1.251.1.1.44.1.1.8 |
mgmtBytesRcvdManagement Bytes Receivedro Counter .1.3.6.1.4.1.251.1.1.44.1.1.9 |
mgmtBytesSentManagement Bytes Sentro Counter .1.3.6.1.4.1.251.1.1.44.1.1.10 |
mgmtResetStatManagement Reset Statisticsrw Enumeration .1.3.6.1.4.1.251.1.1.44.1.1.11 |