DOCS-QOS-MIB
This is the management information for Quality Of Service (QOS) for DOCSIS 1.1.
Main OID:
docsQosMIB.1.3.6.1.2.1.10.127.7
182
Objects
Active
Status
6
Dependencies
Imported Objects
Objects
182 total| Object Name |
|---|
docsQosMIBThis is the management information for
Quality Of Service (QOS) for DOCSIS 1.1. MODULE-IDENTITY .1.3.6.1.2.1.10.127.7 |
docsQosMIBObjects OBJECT IDENTIFIER .1.3.6.1.2.1.10.127.7.1 |
docsQosPktClassTableThis table describes the packet classification
configured on the CM or CMTS.
The model is that a packet either received
as input from an interface or transmitted
for output on an interface may be compared
against an ordered list of rules pertaining to
the packet contents. Each rule is a row of this
table. A matching rule provides a service flow
id to to which the packet is classified.
All rules need to match for a packet to match
a classifier.
The objects in this row correspond to a set of
Classifier Encoding parameters in a DOCSIS
MAC management message. The docsQosPktClassBitMap
indicates which particular parameters were present
in the classifier as signalled in the DOCSIS message.
If the referenced parameter was not present
in the signalled DOCSIS 1.1 Classifier, the
corresponding object in this row reports a
value as specified in the DESCRIPTION section. SEQUENCE OF DocsQosPktClassEntry .1.3.6.1.2.1.10.127.7.1.1 |
docsQosPktClassEntryAn entry in this table provides a single packet
classifier rule. The index ifIndex is an ifType
of docsCableMaclayer(127). DocsQosPktClassEntry .1.3.6.1.2.1.10.127.7.1.1.1 |
docsQosPktClassIdIndex assigned to packet classifier entry by
the CMTS which is unique per service flow. Integer32 .1.3.6.1.2.1.10.127.7.1.1.1.1 |
docsQosPktClassDirectionIndicates the direction to which the classifier
is applied.ro IfDirection .1.3.6.1.2.1.10.127.7.1.1.1.2 |
docsQosPktClassPriorityThe value specifies the order of evaluation
of the classifiers.
The higher the value the higher the priority.
The value of 0 is used as default in
provisioned service flows classifiers.
The default value of 64 is used for dynamic
service flow classifiers.
If the referenced parameter is not present
in a classifier, this object reports the default value
as defined above.ro Integer32 .1.3.6.1.2.1.10.127.7.1.1.1.3 |
docsQosPktClassIpTosLowThe low value of a range of TOS byte values.
If the referenced parameter is not present
in a classifier, this object reports the value of 0.ro OCTET STRING .1.3.6.1.2.1.10.127.7.1.1.1.4 |
docsQosPktClassIpTosHighThe 8-bit high value of a range of TOS byte
values.
If the referenced parameter is not present
in a classifier, this object reports the value of 0.ro OCTET STRING .1.3.6.1.2.1.10.127.7.1.1.1.5 |
docsQosPktClassIpTosMaskThe mask value is bitwise ANDed with TOS byte
in an IP packet and this value is used check
range checking of TosLow and TosHigh.
If the referenced parameter is not present
in a classifier, this object reports the value of 0.ro OCTET STRING .1.3.6.1.2.1.10.127.7.1.1.1.6 |
docsQosPktClassIpProtocolThis object indicates the value of the IP
Protocol field required for IP packets to match
this rule.
The value 256 matches traffic with any IP Protocol
value. The value 257 by convention matches both TCP
and UDP.
If the referenced parameter is not present
in a classifier, this object reports the value of 258.ro Integer32 .1.3.6.1.2.1.10.127.7.1.1.1.7 |
docsQosPktClassIpSourceAddrThis object is deprecated in favor of the
object pair docsQosPktClassInetSourceAddrType
and docsQosPktClassInetSourceAddr. Agents that
choose to implement this object MUST report
an address that matches docsQosPktClassInetSourceAddr
object as long as docsQosPktClassInetSourceAddrType is
ipv4(1). Otherwise, the value of this object shall be
0.0.0.0.rodeprecated IpAddress .1.3.6.1.2.1.10.127.7.1.1.1.8 |
docsQosPktClassIpSourceMaskThis object is deprecated in favor of the
object pair docsQosPktClassInetSourceMaskType
and docsQosPktClassInetSourceMask. Agents that
choose to implement this object MUST report
an address that matches docsQosPktClassInetSourceMask
object as long as docsQosPktClassInetSourceMaskType is
ipv4(1). Otherwise, the value of this object shall be
255.255.255.255.
SNMP mangers should note that agent implementation
of previous versions of this MIB report 0.0.0.0 as the
value when the reference parameter is not present,
rather than 255.255.255.255.rodeprecated IpAddress .1.3.6.1.2.1.10.127.7.1.1.1.9 |
docsQosPktClassIpDestAddrThis object is deprecated in favor of the
object pair docsQosPktClassInetDestAddrType
and docsQosPktClassInetDestAddr. Agents that
choose to implement this object MUST report
an address that matches docsQosPktClassInetDestAddr
object as long as docsQosPktClassInetDestAddrType is
ipv4(1). Otherwise, the value of this object shall be
0.0.0.0.rodeprecated IpAddress .1.3.6.1.2.1.10.127.7.1.1.1.10 |
docsQosPktClassIpDestMaskThis object is deprecated in favor of the
object pair docsQosPktClassInetDestMaskType
and docsQosPktClassInetDestMask. Agents that
choose to implement this object MUST report
an address that matches docsQosPktClassInetDestMask
object as long as docsQosPktClassInetDestMaskType is
ipv4(1). Otherwise, the value of this object shall be
255.255.255.255.
SNMP mangers should note that agent implementation
of previous versions of this MIB report 0.0.0.0 as the
value when the reference parameter is not present,
rather than 255.255.255.255.rodeprecated IpAddress .1.3.6.1.2.1.10.127.7.1.1.1.11 |
docsQosPktClassSourcePortStartThis object specifies the low end inclusive
range of TCP/UDP source port numbers to which
a packet is compared. This object is irrelevant
for non-TCP/UDP IP packets.
If the referenced parameter is not present
in a classifier, this object reports the value of 0.ro Integer32 .1.3.6.1.2.1.10.127.7.1.1.1.12 |
docsQosPktClassSourcePortEndThis object specifies the high end inclusive
range of TCP/UDP source port numbers to which
a packet is compared. This object is irrelevant
for non-TCP/UDP IP packets.
If the referenced parameter is not present
in a classifier, this object reports the value of
65535.ro Integer32 .1.3.6.1.2.1.10.127.7.1.1.1.13 |
docsQosPktClassDestPortStartThis object specifies the low end inclusive
range of TCP/UDP destination port numbers to
which a packet is compared.
If the referenced parameter is not present
in a classifier, this object reports the value of 0.ro Integer32 .1.3.6.1.2.1.10.127.7.1.1.1.14 |
docsQosPktClassDestPortEndThis object specifies the high end inclusive
range of TCP/UDP destination port numbers to which
a packet is compared.
If the referenced parameter is not present
in a classifier, this object reports the value of
65535.ro Integer32 .1.3.6.1.2.1.10.127.7.1.1.1.15 |
docsQosPktClassDestMacAddrAn Ethernet packet matches an entry when its
destination MAC address bitwise ANDed with
docsQosPktClassDestMacMask equals the value of
docsQosPktClassDestMacAddr.
If the referenced parameter is not present
in a classifier, this object reports the value of
'000000000000'H.ro MacAddress (SNMPv2-TC) .1.3.6.1.2.1.10.127.7.1.1.1.16 |
docsQosPktClassDestMacMaskAn Ethernet packet matches an entry when its
destination MAC address bitwise ANDed with
docsQosPktClassDestMacMask equals the value of
docsQosPktClassDestMacAddr.
If the referenced parameter is not present
in a classifier, this object reports the value of
'000000000000'H.ro MacAddress (SNMPv2-TC) .1.3.6.1.2.1.10.127.7.1.1.1.17 |
docsQosPktClassSourceMacAddrAn Ethernet packet matches this entry when its
source MAC address equals the value of
this object.
If the referenced parameter is not present
in a classifier, this object reports the value of
'FFFFFFFFFFFF'H.ro MacAddress (SNMPv2-TC) .1.3.6.1.2.1.10.127.7.1.1.1.18 |
docsQosPktClassEnetProtocolTypeThis object indicates the format of the layer 3
protocol id in the Ethernet packet. A value of
none(0) means that the rule does not use the
layer 3 protocol type as a matching criteria.
A value of ethertype(1) means that the rule
applies only to frames which contains an
EtherType value. Ethertype values are contained
in packets using the Dec-Intel-Xerox (DIX)
encapsulation or the RFC1042 Sub-Network Access
Protocol (SNAP) encapsulation formats.
A value of dsap(2) means that the rule applies
only to frames using the IEEE802.3
encapsulation format with a Destination Service
Access Point (DSAP) other
than 0xAA (which is reserved for SNAP).
A value of mac(3) means that the rule applies
only to MAC management messages for MAC management
messages.
A value of all(4) means that the rule matches
all Ethernet packets.
If the Ethernet frame contains an 802.1P/Q Tag
header (i.e. EtherType 0x8100), this object
applies to the embedded EtherType field within
the 802.1P/Q header.
If the referenced parameter is not present
in a classifier, this object reports the value of 0.ro Enumeration .1.3.6.1.2.1.10.127.7.1.1.1.19 |
docsQosPktClassEnetProtocolIf docsQosEthPktClassProtocolType is none(0),
this object is ignored when considering whether
a packet matches the current rule.
If dosQosPktClassEnetProtocolType is ethertype(1),
this object gives the 16-bit value of the
EtherType that the packet must match in order to
match the rule.
If docsQosPktClassEnetProtocolType is dsap(2), the
lower 8 bits of this object's value must match the
DSAP byte of the packet in order to match the
rule.
If docsQosPktClassEnetProtocolType is mac(3), the
lower 8 bits of this object value represent a
lower bound (inclusive) of MAC management message
type codes matched, and the upper 8 bits of this
object value represent the upper bound (inclusive)
of matched MAC message type codes. Certain
message type codes are excluded from matching, as
specified in the reference.
If the Ethernet frame contains an 802.1P/Q Tag header
(i.e. EtherType 0x8100), this object applies to the
embedded EtherType field within the 802.1P/Q header.
If the referenced parameter is not present in the
classifier, the value of this object is reported as 0.ro Integer32 .1.3.6.1.2.1.10.127.7.1.1.1.20 |
docsQosPktClassUserPriAppliesThis object is obsolete.roobsolete TruthValue (SNMPv2-TC) .1.3.6.1.2.1.10.127.7.1.1.1.21 |
docsQosPktClassUserPriLowThis object applies only to Ethernet frames
using the 802.1P/Q tag header (indicated with
EtherType 0x8100). Such frames include a 16-bit
Tag that contains a 3 bit Priority field and
a 12 bit VLAN number.
Tagged Ethernet packets must have a 3-bit
Priority field within the range of
docsQosPktClassPriLow and docsQosPktClassPriHigh in
order to match this rule.
If the referenced parameter is not present in the
classifier, the value of this object is reported as 0.ro Integer32 .1.3.6.1.2.1.10.127.7.1.1.1.22 |
docsQosPktClassUserPriHighThis object applies only to Ethernet frames
using the 802.1P/Qtag header (indicated with
EtherType 0x8100). Such frames include a 16-bit
Tag that contains a 3 bit Priority field and
a 12 bit VLAN number.
Tagged Ethernet packets must have a 3-bit
Priority field within the range of
docsQosPktClassPriLow and
docsQosPktClassPriHigh in order to match this
rule.
If the referenced parameter is not present in the
classifier, the value of this object is reported
as 7.ro Integer32 .1.3.6.1.2.1.10.127.7.1.1.1.23 |
docsQosPktClassVlanIdThis object applies only to Ethernet frames
using the 802.1P/Q tag header.
If this object's value is nonzero, tagged
packets must have a VLAN Identifier that matches
the value in order to match the rule.
Only the least significant 12 bits of this object's
value are valid.
If the referenced parameter is not present in the
classifier, the value of this object is reported
as 0.ro Integer32 .1.3.6.1.2.1.10.127.7.1.1.1.24 |
docsQosPktClassStateThis object indicates whether or not the classifier
is enabled to classify packets to a Service Flow.
If the referenced parameter is not present in the
classifier, the value of this object is reported
as active(1).ro Enumeration .1.3.6.1.2.1.10.127.7.1.1.1.25 |
docsQosPktClassPktsThis object counts the number of packets that have
been classified using this entry.ro Counter32 .1.3.6.1.2.1.10.127.7.1.1.1.26 |
docsQosPktClassBitMapThis object indicates which parameter encodings were
actually present in the DOCSIS packet classifier
encoding signaled in the DOCSIS message that
created or modified the classifier. Note that
Dynamic Service Change messages have replace
semantics, so that all non-default parameters must
be present whether the classifier is being created
or changed.
A bit of of this object is set to 1 if the parameter
indicated by the comment was present in the classifier
encoding, and 0 otherwise.
Note that BITS are encoded most significant bit
first, so that if e.g. bits 6 and 7 are set, this object
is encoded as the octet string '030000'H.ro Bits .1.3.6.1.2.1.10.127.7.1.1.1.27 |
docsQosPktClassInetSourceAddrTypeThe type of the internet address for
docsQosPktClassInetSourceAddr. This type must be
the same as the docsQosPktClassInetSourceMaskType.
If the referenced parameter is not present
in a classifier, this object reports the value of
ipv4(1).ro InetAddressType (INET-ADDRESS-MIB) .1.3.6.1.2.1.10.127.7.1.1.1.28 |
docsQosPktClassInetSourceAddrThis object specifies the value of the IP
Source Address required for packets to match
this rule. An IP packet matches the rule when
the packet ip source address bitwise ANDed
with the docsQosPktClassInetSourceMask value
equals the docsQosPktClassInetSourceAddr value.
If the referenced parameter is not present
in a classifier, this object reports the value of
'00000000'H.ro InetAddress (INET-ADDRESS-MIB) .1.3.6.1.2.1.10.127.7.1.1.1.29 |
docsQosPktClassInetSourceMaskTypeThe type of the internet address for
docsQosPktClassInetSourceMask. This type must be
the same as the docsQosPktClassInetSourceAddrType.
If the referenced parameter is not present
in a classifier, this object reports the value of
ipv4(1).ro InetAddressType (INET-ADDRESS-MIB) .1.3.6.1.2.1.10.127.7.1.1.1.30 |
docsQosPktClassInetSourceMaskThis object specifies which bits of a packet's
IP Source Address that are compared to match
this rule.
An IP packet matches the rule when the packet
source address bitwise ANDed with the
docsQosPktClassInetSourceMask value equals the
docsQosIpPktClassInetSourceAddr value.
If the referenced parameter is not present
in a classifier, this object reports the value of
'FFFFFFFF'H.ro InetAddress (INET-ADDRESS-MIB) .1.3.6.1.2.1.10.127.7.1.1.1.31 |
docsQosPktClassInetDestAddrTypeThe type of the internet address for
docsQosPktClassInetDestAddr. This type must be
the same as the docsQosPktClassInetDestMaskType.
If the referenced parameter is not present
in a classifier, this object reports the value of
ipv4(1).ro InetAddressType (INET-ADDRESS-MIB) .1.3.6.1.2.1.10.127.7.1.1.1.32 |
docsQosPktClassInetDestAddrThis object specifies the value of the IP
Destination Address required for packets to match
this rule. An IP packet matches the rule when
the packet ip destination address
bitwise ANDed with the
docsQosPktClassInetDestMask value
equals the docsQosPktClassInetDestAddr value.
If the referenced parameter is not present
in a classifier, this object reports the value of
'00000000'H.ro InetAddress (INET-ADDRESS-MIB) .1.3.6.1.2.1.10.127.7.1.1.1.33 |
docsQosPktClassInetDestMaskTypeThe type of the internet address for
docsQosPktClassInetDestMask. This type must be
the same as the docsQosPktClassInetDestAddrType.
If the referenced parameter is not present
in a classifier, this object reports the value of
ipv4(1).ro InetAddressType (INET-ADDRESS-MIB) .1.3.6.1.2.1.10.127.7.1.1.1.34 |
docsQosPktClassInetDestMaskThis object specifies which bits of a packet's
IP Destination Address that are compared to
match this rule.
An IP packet matches the rule when the packet
destination address bitwise ANDed with the
docsQosPktClassInetDestMask value equals the
docsQosIpPktClassInetDestAddr value.
If the referenced parameter is not present
in a classifier, this object reports the value of
'FFFFFFFF'H.ro InetAddress (INET-ADDRESS-MIB) .1.3.6.1.2.1.10.127.7.1.1.1.35 |
docsQosParamSetTableThis table describes the set of DOCSIS 1.1 QOS
parameters defined in a managed device.
The ifIndex index specifies a DOCSIS MAC Domain.
The docsQosServiceFlowId index specifies a particular
Service Flow.
The docsQosParamSetType index indicates whether
the active, admitted, or provisioned QOS Parameter
Set is being described by the row.
Only the QOS Parameter Sets of Docsis 1.1 service
flows are represented in this table. Docsis 1.0
QOS service profiles are not represented in this
table.
Each row corresponds to a DOCSIS QOS Parameter Set
as signaled via DOCSIS MAC management messages.
Each object in the row corresponds to one or
part of one DOCSIS 1.1 Service Flow Encoding.
The docsQosParamSetBitMap object in the row indicates
which particular parameters were signalled in
the original registration or dynamic service
request message that created the QOS Parameter Set.
In many cases, even if a QOS Parameter Set parameter
was not signalled, the DOCSIS specification calls
for a default value to be used. That default value
is reported as the value of the corresponding object
in this row.
Many objects are not applicable depending on
the service flow direction or upstream scheduling
type. The object value reported in this case
is specified in the DESCRIPTION clause. SEQUENCE OF DocsQosParamSetEntry .1.3.6.1.2.1.10.127.7.1.2 |
docsQosParamSetEntryA unique set of QOS parameters. DocsQosParamSetEntry .1.3.6.1.2.1.10.127.7.1.2.1 |
docsQosParamSetServiceClassNameRefers to the Service Class Name that the
parameter set values were derived.
If the referenced parameter is not present in the
corresponding DOCSIS QOS Parameter Set, the default
value of this object is a zero length string.ro DisplayString (SNMPv2-TC) .1.3.6.1.2.1.10.127.7.1.2.1.4 |
docsQosParamSetPriorityThe relative priority of a service flow.
Higher numbers indicate higher priority.
This priority should only be used to differentiate
service flow with identical parameter sets.
If the referenced parameter is not present in the
corresponding DOCSIS QOS Parameter Set, the default
value of this object is 0. If the parameter is
not applicable, the reported value is 0.ro Integer32 .1.3.6.1.2.1.10.127.7.1.2.1.5 |
docsQosParamSetMaxTrafficRateMaximum sustained traffic rate allowed for this
service flow in bits/sec. Must count all MAC frame
data PDU from the bytes following the MAC header HCS to
the end of the CRC. The number of bytes
forwarded is limited during any time interval.
The value 0 means no maximum traffic rate is
enforced. This object applies to both upstream and
downstream service flows.
If the referenced parameter is not present in the
corresponding DOCSIS QOS Parameter Set, the default
value of this object is 0. If the parameter is
not applicable, it is reported as 0.ro BitRate .1.3.6.1.2.1.10.127.7.1.2.1.6 |
docsQosParamSetMaxTrafficBurstSpecifies the token bucket size in bytes
for this parameter set. The value is calculated
from the byte following the MAC header HCS to
the end of the CRC. This object is applied in
conjunction with docsQosParamSetMaxTrafficRate to
calculate maximum sustained traffic rate.
If the referenced parameter is not present in the
corresponding DOCSIS QOS Parameter Set, the default
value of this object for scheduling types
bestEffort (2), nonRealTimePollingService(3),
and realTimePollingService(4) is 1522.
If this parameter is not applicable, it is reported
as 0.ro Unsigned32 .1.3.6.1.2.1.10.127.7.1.2.1.7 |
docsQosParamSetMinReservedRateSpecifies the guaranteed minimum rate in
bits/sec for this parameter set. The value is
calculated from the byte following the MAC
header HCS to the end of the CRC. The default
value of 0 has the meaning that no bandwidth
is reserved.
If the referenced parameter is not present in the
corresponding DOCSIS QOS Parameter Set, the default
value of this object is 0. If the parameter
is not applicable, it is reported as 0.ro BitRate .1.3.6.1.2.1.10.127.7.1.2.1.8 |
docsQosParamSetMinReservedPktSpecifies an assumed minimum packet size in
bytes for which the docsQosParamSetMinReservedRate
will be provided. The value is calculated from
the byte following the MAC header HCS to the
end of the CRC.
If the referenced parameter is omitted from a
DOCSIS QOS parameter set, the default value is
CMTS implementation dependent. In this case, the
CMTS reports the default value it is using and the
CM reports a value of 0. If the referenced
parameter is not applicable to the direction or
scheduling type of the service flow, both CMTS and
CM report this object's value as 0.ro Integer32 .1.3.6.1.2.1.10.127.7.1.2.1.9 |
docsQosParamSetActiveTimeoutSpecifies the maximum duration in seconds that
resources remain unused on an active service
flow before CMTS signals that both active and
admitted parameters set are null.
The default value of 0 signifies an
infinite amount of time.
If the referenced parameter is not present in the
corresponding DOCSIS QOS Parameter Set, the default
value of this object is 0.ro Integer32 .1.3.6.1.2.1.10.127.7.1.2.1.10 |
docsQosParamSetAdmittedTimeoutSpecifies the maximum duration in seconds that
resources remain in admitted state before
resources must be released.
The value of 0 signifies an infinite amount
of time.
If the referenced parameter is not present in the
corresponding DOCSIS QOS Parameter Set, the
default value of this object is 200.ro Integer32 .1.3.6.1.2.1.10.127.7.1.2.1.11 |
docsQosParamSetMaxConcatBurstSpecifies the maximum concatenated burst in
bytes which an upstream service flow is allowed.
The value is calculated from the FC byte of the
Concatenation MAC Header to the last CRC byte in
of the last concatenated MAC frame, inclusive.
The value of 0 specifies no maximum burst.
If the referenced parameter is not present in the
corresponding DOCSIS QOS Parameter Set, the default
value of this object is 0. If the parameter is
not applicable, this object's value is reported
as 0.ro Integer32 .1.3.6.1.2.1.10.127.7.1.2.1.12 |
docsQosParamSetSchedulingTypeSpecifies the upstream scheduling service used for
upstream service flow.
If the referenced parameter is not present in the
corresponding DOCSIS QOS Parameter Set of an
upstream service flow, the default value of this
object is bestEffort(2). For QOS parameter sets of
downstream service flows, this object's value is
reported as undefined(1).ro SchedulingType .1.3.6.1.2.1.10.127.7.1.2.1.13 |
docsQosParamSetNomPollIntervalSpecifies the nominal interval in microseconds
between successive unicast request
opportunities on an upstream service flow.
This object applies only to upstream service flows
with schedulingType of value
nonRealTimePollingService(3),
realTimePollingService(4), and
unsolictedGrantServiceWithAD(5). The parameter is
mandatory for realTimePollingService(4). If the
parameter is omitted with
nonRealTimePollingService(3), the CMTS uses an
implementation dependent value. If the parameter
is omitted with unsolictedGrantServiceWithAD(5),
the CMTS uses as a default value the value of the
Nominal Grant Interval parameter. In all cases,
the CMTS reports the value it is using when the
parameter is applicable. The CM reports the
signaled parameter value if it was signaled,
and 0 otherwise.
If the referenced parameter is not applicable to
the direction or scheduling type of the
corresponding DOCSIS QOS Parameter Set, both
CMTS and CM report this object's value as 0.ro Unsigned32 UNITS "microseconds" .1.3.6.1.2.1.10.127.7.1.2.1.15 |
docsQosParamSetTolPollJitterSpecifies the maximum amount of time in
microseconds that the unicast request interval
may be delayed from the nominal periodic
schedule on an upstream service flow.
This parameter is applicable only to upstream
service flows with a Schedulingtype of
realTimePollingService(4) or
unsolictedGrantServiceWithAD(5).
If the referenced parameter is applicable but not
present in the corresponding DOCSIS QOS Parameter
Set, the CMTS uses an implementation dependent
value and reports the value it is using.
The CM reports a value of 0 in this case.
If the parameter is not applicable to the
direction or upstream scheduling type of the
service flow, both CMTS and CM report this
object's value as 0.ro Unsigned32 UNITS "microseconds" .1.3.6.1.2.1.10.127.7.1.2.1.16 |
docsQosParamSetUnsolicitGrantSizeSpecifies the unsolicited grant size in bytes.
The grant size includes the entire MAC frame
data PDU from the Frame Control byte to end of
the MAC frame.
The referenced parameter is applicable only
for upstream flows with a SchedulingType of
of unsolicitedGrantServicewithAD(5) or
unsolicitedGrantService(6), and is mandatory
when applicable. Both CMTS and CM report
the signaled value of the parameter in this
case.
If the referenced parameter is not applicable to
the direction or scheduling type of the
corresponding DOCSIS QOS Parameter Set, both
CMTS and CM report this object's value as 0.ro Integer32 .1.3.6.1.2.1.10.127.7.1.2.1.17 |
docsQosParamSetNomGrantIntervalSpecifies the nominal interval in microseconds
between successive data grant opportunities
on an upstream service flow.
The referenced parameter is applicable only
for upstream flows with a SchedulingType of
of unsolicitedGrantServicewithAD(5) or
unsolicitedGrantService(6), and is mandatory
when applicable. Both CMTS and CM report the
signaled value of the parameter in this case.
If the referenced parameter is not applicable to
the direction or scheduling type of the
corresponding DOCSIS QOS Parameter Set, both
CMTS and CM report this object's value as 0.ro Unsigned32 UNITS "microseconds" .1.3.6.1.2.1.10.127.7.1.2.1.18 |
docsQosParamSetTolGrantJitterSpecifies the maximum amount of time in
microseconds that the transmission opportunities
may be delayed from the nominal periodic schedule.
The referenced parameter is applicable only
for upstream flows with a SchedulingType of
of unsolicitedGrantServicewithAD(5) or
unsolicitedGrantService(6), and is mandatory
when applicable. Both CMTS and CM report the
signaled value of the parameter in this case.
If the referenced parameter is not applicable to
the direction or scheduling type of the
corresponding DOCSIS QOS Parameter Set, both
CMTS and CM report this object's value as 0.ro Unsigned32 UNITS "microseconds" .1.3.6.1.2.1.10.127.7.1.2.1.19 |
docsQosParamSetGrantsPerIntervalSpecifies the number of data grants per Nominal
Grant Interval
(docsQosParamSetNomGrantInterval).
The referenced parameter is applicable only
for upstream flows with a SchedulingType of
of unsolicitedGrantServicewithAD(5) or
unsolicitedGrantService(6), and is mandatory
when applicable. Both CMTS and CM report the
signaled value of the parameter in this case.
If the referenced parameter is not applicable to
the direction or scheduling type of the
corresponding DOCSIS QOS Parameter Set, both
CMTS and CM report this object's value as 0.ro Integer32 .1.3.6.1.2.1.10.127.7.1.2.1.20 |
docsQosParamSetTosAndMaskSpecifies the AND mask for IP TOS byte for overwriting
IP packets TOS value. The IP packets TOS byte is
bitwise ANDed with docsQosParamSetTosAndMask and
result is bitwise ORed with docsQosParamSetTosORMask
and result is written to IP packet TOS byte.
A value of 'FF'H for docsQosParamSetTosAndMask and
a value of '00'H for docsQosParamSetTosOrMask means
that IP Packet TOS byte is not overwritten.
Even though the this object is only enforced by the
Cable Modem Termination System (CMTS),
Cable Modems must report the value as signaled in
the referenced parameter.
This combination is reported if the referenced
parameter is not present in a QOS Parameter Set.ro OCTET STRING .1.3.6.1.2.1.10.127.7.1.2.1.21 |
docsQosParamSetTosOrMaskSpecifies the OR mask for IP TOS byte.
See the description of docsQosParamSetTosAndMask
for further details.ro OCTET STRING .1.3.6.1.2.1.10.127.7.1.2.1.22 |
docsQosParamSetMaxLatencySpecifies the maximum latency between the
reception of a packet by the CMTS on its NSI
and the forwarding of the packet to the RF
interface. A value of 0 signifies no maximum
latency enforced. This object only applies to
downstream service flows.
If the referenced parameter is not present in the
corresponding downstream DOCSIS QOS Parameter Set,
the default value is 0. This parameter is
not applicable to upstream DOCSIS QOS Parameter Sets,
and its value is reported as 0 in this case.ro Unsigned32 UNITS "microseconds" .1.3.6.1.2.1.10.127.7.1.2.1.23 |
docsQosParamSetTypeDefines the type of the QOS parameter set defined
by this row. active(1) indicates the Active QOS
parameter set, describing the service currently
being provided by the Docsis MAC domain to the
service flow. admitted(2) indicates the Admitted
QOS Parameter Set, describing services reserved by
by the Docsis MAC domain for use by the service flow.
provisioned (3) describes the QOS Parameter Set
defined in the DOCSIS CM Configuration file for
the service flow. Enumeration .1.3.6.1.2.1.10.127.7.1.2.1.24 |
docsQosParamSetRequestPolicyOctSpecifies which transmit interval opportunities
the CM omits for upstream transmission requests and
packet transmissions. This object takes its
default value for downstream service flows.
Unless otherwise indicated, a bit value of 1 means
that a CM must *not* use that opportunity for
upstream transmission.
Calling bit 0 the least significant bit of the
least significant (4th) octet, and increasing
bit number with significance, the bit definitions
are as defined below:
broadcastReqOpp(0):
all CMs broadcast request opportunities
priorityReqMulticastReq(1):
priority request multicast request opportunities
reqDataForReq(2):
request/data opportunities for requests
reqDataForData(3):
request/data opportunities for data
piggybackReqWithData(4):
piggyback requests with data
concatenateData(5):
concatenate data
fragmentData(6):
fragment data
suppresspayloadheaders(7):
suppress payload headers
dropPktsExceedUGSize(8):
A value of 1 mean that service flow must drop
packet that do not fit in the Unsolicited
Grant size
If the referenced parameter is not present in
a QOS Parameter Set, the value of this object is
reported as '00000000'H.ro OCTET STRING .1.3.6.1.2.1.10.127.7.1.2.1.25 |
docsQosParamSetBitMapThis object indicates the set of QOS Parameter
Set parameters actually signaled in the
DOCSIS registration or dynamic service request
message that created or modified the QOS Parameter Set.
A bit is set to 1 when the parameter described
by the indicated reference section is present
in the original request.
Note that when Service Class names are expanded,
the registration or dynamic response message may
contain parameters as expanded by the CMTS based
on a stored service class. These expanded
parameters are *not* indicated by a 1 bit in this
object.
Note that even though some QOS Parameter Set
parameters may not be signalled in a message
(so that the paramater's bit in this object is 0)
the DOCSIS specification calls for default
values to be used. These default values are
reported as the corresponding object's value in
the row.
Note that BITS objects are encoded most
significant bit first. For example, if bits
1 and 16 are set, the value of this object
is the octet string '400080'H.ro Bits .1.3.6.1.2.1.10.127.7.1.2.1.26 |
docsQosServiceFlowTableThis table describes the set of Docsis-QOS
Service Flows in a managed device. SEQUENCE OF DocsQosServiceFlowEntry .1.3.6.1.2.1.10.127.7.1.3 |
docsQosServiceFlowEntryDescribes a service flow.
An entry in the table exists for each
Service Flow ID. The ifIndex is an
ifType of docsCableMaclayer(127). DocsQosServiceFlowEntry .1.3.6.1.2.1.10.127.7.1.3.1 |
docsQosServiceFlowIdAn index assigned to a service flow by CMTS. Unsigned32 .1.3.6.1.2.1.10.127.7.1.3.1.1 |
docsQosServiceFlowProvisionedParamSetIndexThis object is obsolete.roobsolete Unsigned32 .1.3.6.1.2.1.10.127.7.1.3.1.3 |
docsQosServiceFlowAdmittedParamSetIndexThis object is obsolete.roobsolete Unsigned32 .1.3.6.1.2.1.10.127.7.1.3.1.4 |
docsQosServiceFlowActiveParamSetIndexThis object is obsolete.roobsolete Unsigned32 .1.3.6.1.2.1.10.127.7.1.3.1.5 |
docsQosServiceFlowSIDService Identifier (SID) assigned to an
admitted or active service flow. This object
reports a value of 0 if a Service Id is not
associated with the service flow. Only active
or admitted upstream service flows will have a
Service Id (SID).ro Unsigned32 .1.3.6.1.2.1.10.127.7.1.3.1.6 |
docsQosServiceFlowDirectionThe direction of the service flow.ro IfDirection .1.3.6.1.2.1.10.127.7.1.3.1.7 |
docsQosServiceFlowPrimaryObject reflects whether service flow is the primary
or a secondary service flow.
A primary service flow is the default service flow
for otherwise unclassified traffic and all MAC
messages.ro TruthValue (SNMPv2-TC) .1.3.6.1.2.1.10.127.7.1.3.1.8 |
docsQosServiceFlowActiveTimeoutThis object is obsolete.roobsolete Integer32 .1.3.6.1.2.1.10.127.7.1.3.1.9 |
docsQosServiceFlowAdmittedTimeoutThis object is obsolete.roobsolete Integer32 .1.3.6.1.2.1.10.127.7.1.3.1.10 |
docsQosServiceFlowSchedulingTypeThis object is obsolete.roobsolete SchedulingType .1.3.6.1.2.1.10.127.7.1.3.1.11 |
docsQosServiceFlowRequestPolicyThis object is obsolete.roobsolete OCTET STRING .1.3.6.1.2.1.10.127.7.1.3.1.12 |
docsQosServiceFlowTosAndMaskThis object is obsolete.roobsolete OCTET STRING .1.3.6.1.2.1.10.127.7.1.3.1.13 |
docsQosServiceFlowTosOrMaskThis object is obsolete.roobsolete OCTET STRING .1.3.6.1.2.1.10.127.7.1.3.1.14 |
docsQosServiceFlowStatsTableThis table describes statistics associated with the
Service Flows in a managed device. SEQUENCE OF DocsQosServiceFlowStatsEntry .1.3.6.1.2.1.10.127.7.1.4 |
docsQosServiceFlowStatsEntryDescribes a set of service flow statistics.
An entry in the table exists for each
Service Flow ID. The ifIndex is an
ifType of docsCableMaclayer(127). DocsQosServiceFlowStatsEntry .1.3.6.1.2.1.10.127.7.1.4.1 |
docsQosServiceFlowPktsThe number of Packet Data PDUs classified to this
service flow. This object does not count MAC-specific
management messages.
CMs not classifying downstream packets may report
this object's value as 0.ro Counter32 .1.3.6.1.2.1.10.127.7.1.4.1.1 |
docsQosServiceFlowOctetsThe number of octets transmitted on the Docsis RF network
from the byte after the MAC header HCS to the end
of the CRC for all packets counted in the
docsQosServiceFlowPkts object for this row. Note that
this counts the octets after payload header suppression
has been applied. CMs not classifying to a downstream
service flow may report this object's value as 0 for that
flow.ro Counter32 .1.3.6.1.2.1.10.127.7.1.4.1.2 |
docsQosServiceFlowTimeCreatedThe value of sysUpTime when the service flow
was created.ro TimeStamp (SNMPv2-TC) .1.3.6.1.2.1.10.127.7.1.4.1.3 |
docsQosServiceFlowTimeActiveThe total time that service flow has been active.ro Counter32 UNITS "seconds" .1.3.6.1.2.1.10.127.7.1.4.1.4 |
docsQosServiceFlowPHSUnknownsThe number of packets received on the service flow
with an unknown payload header suppression index.ro Counter32 .1.3.6.1.2.1.10.127.7.1.4.1.5 |
docsQosServiceFlowPolicedDropPktsThe number of packets dropped due to policing of
the service flow, especially to limit the maximum
rate of the flow.ro Counter32 .1.3.6.1.2.1.10.127.7.1.4.1.6 |
docsQosServiceFlowPolicedDelayPktsThe number of packet delayed due to policing of
the service flow, especially to limit the maximum
rate of the flow.ro Counter32 .1.3.6.1.2.1.10.127.7.1.4.1.7 |
docsQosUpstreamStatsTableThis table describes statistics associated with
upstream service flows. All counted frames must
be received without an FCS error. SEQUENCE OF DocsQosUpstreamStatsEntry .1.3.6.1.2.1.10.127.7.1.5 |
docsQosUpstreamStatsEntryDescribes a set of upstream service flow statistics.
An entry in the table exists for each
upstream Service Flow in a managed device.
The ifIndex is an ifType of docsCableMaclayer(127). DocsQosUpstreamStatsEntry .1.3.6.1.2.1.10.127.7.1.5.1 |
docsQosSIDIdentifies a service id for an admitted or active
upstream service flow. Integer32 .1.3.6.1.2.1.10.127.7.1.5.1.1 |
docsQosUpstreamFragmentsThe number of fragmentation headers received on an
upstream service flow, regardless of whether
the fragment was correctly reassembled into a
valid packet.ro Counter32 .1.3.6.1.2.1.10.127.7.1.5.1.2 |
docsQosUpstreamFragDiscardsThe number of upstream fragments discarded and not
assembled into a valid upstream packet.ro Counter32 .1.3.6.1.2.1.10.127.7.1.5.1.3 |
docsQosUpstreamConcatBurstsThe number of concatenation headers received on an
upstream service flow.ro Counter32 .1.3.6.1.2.1.10.127.7.1.5.1.4 |
docsQosDynamicServiceStatsTableThis table describes statistics associated with the
Dynamic Service Flows in a managed device. SEQUENCE OF DocsQosDynamicServiceStatsEntry .1.3.6.1.2.1.10.127.7.1.6 |
docsQosDynamicServiceStatsEntryDescribes a set of dynamic service flow statistics.
Two entries exist for each Docsis mac layer
interface for the upstream and downstream direction.
On the CMTS, the downstream direction row indicates
messages transmitted or transactions originated
by the CMTS. The upstream direction row indicates
messages received or transaction originated by the
CM. On the CM, the downstream direction row
indicates messages received or transactions
originated by the CMTS. The upstream direction
row indicates messages transmitted by the CM or
transactions originated by the CM.
The ifIndex is an ifType of docsCableMaclayer(127). DocsQosDynamicServiceStatsEntry .1.3.6.1.2.1.10.127.7.1.6.1 |
docsQosIfDirectionThe direction of interface. IfDirection .1.3.6.1.2.1.10.127.7.1.6.1.1 |
docsQosDSAReqsThe number of Dynamic Service Addition Requests,
including retries.ro Counter32 .1.3.6.1.2.1.10.127.7.1.6.1.2 |
docsQosDSARspsThe number of Dynamic Service Addition Responses,
including retries.ro Counter32 .1.3.6.1.2.1.10.127.7.1.6.1.3 |
docsQosDSAAcksThe number of Dynamic Service Addition Acknowledgements,
including retries.ro Counter32 .1.3.6.1.2.1.10.127.7.1.6.1.4 |
docsQosDSCReqsThe number of Dynamic Service Change Requests,
including retries.ro Counter32 .1.3.6.1.2.1.10.127.7.1.6.1.5 |
docsQosDSCRspsThe number of Dynamic Service Change Responses,
including retries.ro Counter32 .1.3.6.1.2.1.10.127.7.1.6.1.6 |
docsQosDSCAcksThe number of Dynamic Service Change Acknowledgements,
including retries.ro Counter32 .1.3.6.1.2.1.10.127.7.1.6.1.7 |
docsQosDSDReqsThe number of Dynamic Service Delete Requests,
including retries.ro Counter32 .1.3.6.1.2.1.10.127.7.1.6.1.8 |
docsQosDSDRspsThe number of Dynamic Service Delete Responses,
including retries.ro Counter32 .1.3.6.1.2.1.10.127.7.1.6.1.9 |
docsQosDynamicAddsThe number of successful Dynamic Service Addition
transactions.ro Counter32 .1.3.6.1.2.1.10.127.7.1.6.1.10 |
docsQosDynamicAddFailsThe number of failed Dynamic Service Addition
transactions.ro Counter32 .1.3.6.1.2.1.10.127.7.1.6.1.11 |
docsQosDynamicChangesThe number of successful Dynamic Service Change
transactions.ro Counter32 .1.3.6.1.2.1.10.127.7.1.6.1.12 |
docsQosDynamicChangeFailsThe number of failed Dynamic Service Change
transactions.ro Counter32 .1.3.6.1.2.1.10.127.7.1.6.1.13 |
docsQosDynamicDeletesThe number of successful Dynamic Service Delete
transactions.ro Counter32 .1.3.6.1.2.1.10.127.7.1.6.1.14 |
docsQosDynamicDeleteFailsThe number of failed Dynamic Service Delete
transactions.ro Counter32 .1.3.6.1.2.1.10.127.7.1.6.1.15 |
docsQosDCCReqsThe number of Dynamic Channel Change Request messages
traversing an interface. This count is nonzero only on
downstream direction rows. This count should
include number of retries.ro Counter32 .1.3.6.1.2.1.10.127.7.1.6.1.16 |
docsQosDCCRspsThe number of Dynamic Channel Change Response messages
traversing an interface. This count is nonzero
only on upstream direction rows. This count should
include number of retries.ro Counter32 .1.3.6.1.2.1.10.127.7.1.6.1.17 |
docsQosDCCAcksThe number of Dynamic Channel Change Acknowledgement
messages traversing an interface. This count
is nonzero only on downstream direction rows.
This count should include number of retries.ro Counter32 .1.3.6.1.2.1.10.127.7.1.6.1.18 |
docsQosDCCsThe number of successful Dynamic Channel Change
transactions. This count is nonzero only on downstream
direction rows.ro Counter32 .1.3.6.1.2.1.10.127.7.1.6.1.19 |
docsQosDCCFailsThe number of failed Dynamic Channel Change
transactions. This count is nonzero only on
downstream direction rows.ro Counter32 .1.3.6.1.2.1.10.127.7.1.6.1.20 |
docsQosDCCRspDepartsThe number of Dynamic Channel Change Response (depart)
messages traversing an interface. This count is only counted
on upstream direction rows.ro Counter32 .1.3.6.1.2.1.10.127.7.1.6.1.21 |
docsQosDCCRspArrivesThe number of Dynamic Channel Change Response (arrive)
messages traversing an interface. This count is only counted on
upstream direction rows. This count should include number of retries.ro Counter32 .1.3.6.1.2.1.10.127.7.1.6.1.22 |
docsQosServiceFlowLogTableThis table contains a log of the disconnected
Service Flows in a managed device. SEQUENCE OF DocsQosServiceFlowLogEntry .1.3.6.1.2.1.10.127.7.1.7 |
docsQosServiceFlowLogEntryThe information regarding a single disconnected
service flow. DocsQosServiceFlowLogEntry .1.3.6.1.2.1.10.127.7.1.7.1 |
docsQosServiceFlowLogIndexUnique index for a logged service flow. Unsigned32 .1.3.6.1.2.1.10.127.7.1.7.1.1 |
docsQosServiceFlowLogIfIndexThe ifIndex of ifType docsCableMaclayer(127)
on the CMTS where the service flow was present.ro InterfaceIndex (IF-MIB) .1.3.6.1.2.1.10.127.7.1.7.1.2 |
docsQosServiceFlowLogSFIDThe index assigned to the service flow by the CMTS.ro Unsigned32 .1.3.6.1.2.1.10.127.7.1.7.1.3 |
docsQosServiceFlowLogCmMacThe MAC address for the cable modem associated with
the service flow.ro MacAddress (SNMPv2-TC) .1.3.6.1.2.1.10.127.7.1.7.1.4 |
docsQosServiceFlowLogPktsThe number of packets counted on this service flow
after payload header suppression.ro Counter32 .1.3.6.1.2.1.10.127.7.1.7.1.5 |
docsQosServiceFlowLogOctetsThe number of octets counted on this service flow
after payload header suppression.ro Counter32 .1.3.6.1.2.1.10.127.7.1.7.1.6 |
docsQosServiceFlowLogTimeDeletedThe value of sysUpTime when the service flow
was deleted.ro TimeStamp (SNMPv2-TC) .1.3.6.1.2.1.10.127.7.1.7.1.7 |
docsQosServiceFlowLogTimeCreatedThe value of sysUpTime when the service flow
was created.ro TimeStamp (SNMPv2-TC) .1.3.6.1.2.1.10.127.7.1.7.1.8 |
docsQosServiceFlowLogTimeActiveThe total time that service flow was active.ro Counter32 UNITS "seconds" .1.3.6.1.2.1.10.127.7.1.7.1.9 |
docsQosServiceFlowLogDirectionThe value of docsQosServiceFlowDirection
for the service flow.ro IfDirection .1.3.6.1.2.1.10.127.7.1.7.1.11 |
docsQosServiceFlowLogPrimaryThe value of docsQosServiceFlowPrimary for the
service flow.ro TruthValue (SNMPv2-TC) .1.3.6.1.2.1.10.127.7.1.7.1.12 |
docsQosServiceFlowLogServiceClassNameThe value of docsQosParamSetServiceClassName for
the provisioned QOS Parameter Set of the
service flow.ro DisplayString (SNMPv2-TC) .1.3.6.1.2.1.10.127.7.1.7.1.13 |
docsQosServiceFlowLogPolicedDropPktsThe final value of docsQosServiceFlowPolicedDropPkts
for the service flow.ro Counter32 .1.3.6.1.2.1.10.127.7.1.7.1.14 |
docsQosServiceFlowLogPolicedDelayPktsThe final value of docsQosServiceFlowPolicedDelayPkts
for the service flow.ro Counter32 .1.3.6.1.2.1.10.127.7.1.7.1.15 |
docsQosServiceFlowLogControlSetting this object to the value destroy(6) removes
this entry from the table.
Reading this object return the value active(1).rw Enumeration .1.3.6.1.2.1.10.127.7.1.7.1.16 |
docsQosServiceClassTableThis table describes the set of Docsis-QOS
Service Classes in a CMTS. SEQUENCE OF DocsQosServiceClassEntry .1.3.6.1.2.1.10.127.7.1.8 |
docsQosServiceClassEntryA provisioned service class on a CMTS.
Each entry defines a template for certain
DOCSIS QOS Parameter Set values. When a CM
creates or modifies an Admitted QOS Parameter Set for a
Service Flow, it may reference a Service Class
Name instead of providing explicit QOS Parameter
Set values. In this case, the CMTS populates
the QOS Parameter Set with the applicable
corresponding values from the named Service Class.
Subsequent changes to a Service Class row do *not*
affect the QOS Parameter Set values of any service flows
already admitted.
A service class template applies to only
a single direction, as indicated in the
docsQosServiceClassDirection object. DocsQosServiceClassEntry .1.3.6.1.2.1.10.127.7.1.8.1 |
docsQosServiceClassNameService Class Name. DOCSIS specifies that the
maximum size is 15 printable ASCII characters with
a terminating zero. The terminating zero is not
represented in this DisplayString syntax object. DisplayString .1.3.6.1.2.1.10.127.7.1.8.1.1 |
docsQosServiceClassParamSetIndexThis object is obsolete.rwobsolete Unsigned32 .1.3.6.1.2.1.10.127.7.1.8.1.2 |
docsQosServiceClassStatusUsed to create or delete rows in this table.rw RowStatus (SNMPv2-TC) .1.3.6.1.2.1.10.127.7.1.8.1.3 |
docsQosServiceClassPriorityTemplate for docsQosParamSetPriority.rw Integer32 .1.3.6.1.2.1.10.127.7.1.8.1.4 |
docsQosServiceClassMaxTrafficRateTemplate for docsQosParamSetMaxTrafficRate.rw BitRate .1.3.6.1.2.1.10.127.7.1.8.1.5 |
docsQosServiceClassMaxTrafficBurstTemplate for docsQosParamSetMaxTrafficBurst.rw Unsigned32 .1.3.6.1.2.1.10.127.7.1.8.1.6 |
docsQosServiceClassMinReservedRateTemplate for docsQosParamSEtMinReservedRate.rw BitRate .1.3.6.1.2.1.10.127.7.1.8.1.7 |
docsQosServiceClassMinReservedPktTemplate for docsQosParamSetMinReservedPkt.rw Integer32 .1.3.6.1.2.1.10.127.7.1.8.1.8 |
docsQosServiceClassMaxConcatBurstTemplate for docsQosParamSetMaxConcatBurst.rw Integer32 .1.3.6.1.2.1.10.127.7.1.8.1.9 |
docsQosServiceClassNomPollIntervalTemplate for docsQosParamSetNomPollInterval.rw Unsigned32 UNITS "microseconds" .1.3.6.1.2.1.10.127.7.1.8.1.10 |
docsQosServiceClassTolPollJitterTemplate for docsQosParamSetTolPollJitter.rw Unsigned32 UNITS "microseconds" .1.3.6.1.2.1.10.127.7.1.8.1.11 |
docsQosServiceClassUnsolicitGrantSizeTemplate for docsQosParamSetUnsolicitGrantSize.rw Integer32 .1.3.6.1.2.1.10.127.7.1.8.1.12 |
docsQosServiceClassNomGrantIntervalTemplate for docsQosParamSetNomGrantInterval.rw Unsigned32 UNITS "microseconds" .1.3.6.1.2.1.10.127.7.1.8.1.13 |
docsQosServiceClassTolGrantJitterTemplate for docsQosParamSetTolGrantJitter.rw Unsigned32 UNITS "microseconds" .1.3.6.1.2.1.10.127.7.1.8.1.14 |
docsQosServiceClassGrantsPerIntervalTemplate for docsQosParamSetGrantsPerInterval.rw Integer32 .1.3.6.1.2.1.10.127.7.1.8.1.15 |
docsQosServiceClassMaxLatencyTemplate for docsQosParamSetClassMaxLatency.rw Unsigned32 UNITS "microseconds" .1.3.6.1.2.1.10.127.7.1.8.1.16 |
docsQosServiceClassActiveTimeoutTemplate for docsQosParamSetActiveTimeout.rw Integer32 .1.3.6.1.2.1.10.127.7.1.8.1.17 |
docsQosServiceClassAdmittedTimeoutTemplate for docsQosParamSetAdmittedTimeout.rw Integer32 .1.3.6.1.2.1.10.127.7.1.8.1.18 |
docsQosServiceClassSchedulingTypeTemplate for docsQosParamSetSchedulingType.rw SchedulingType .1.3.6.1.2.1.10.127.7.1.8.1.19 |
docsQosServiceClassRequestPolicyTemplate for docsQosParamSetRequestPolicyOct.rw OCTET STRING .1.3.6.1.2.1.10.127.7.1.8.1.20 |
docsQosServiceClassTosAndMaskTemplate for docsQosParamSetTosAndMask.rw OCTET STRING .1.3.6.1.2.1.10.127.7.1.8.1.21 |
docsQosServiceClassTosOrMaskTemplate for docsQosParamSetTosOrMask.rw OCTET STRING .1.3.6.1.2.1.10.127.7.1.8.1.22 |
docsQosServiceClassDirectionSpecifies whether the service class template
applies to upstream or downstream service flows.rw IfDirection .1.3.6.1.2.1.10.127.7.1.8.1.23 |
docsQosServiceClassPolicyTableThis table describes the set of Docsis-QOS
Service Class Policies.
This table is an adjunct to the
docsDevFilterPolicy table. Entries in
docsDevFilterPolicy table can point to
specific rows in this table.
This table permits mapping a packet to a service
class name of an active service flow so long as
a classifier does not exist at a higher
priority. SEQUENCE OF DocsQosServiceClassPolicyEntry .1.3.6.1.2.1.10.127.7.1.9 |
docsQosServiceClassPolicyEntryA service class name policy entry. DocsQosServiceClassPolicyEntry .1.3.6.1.2.1.10.127.7.1.9.1 |
docsQosServiceClassPolicyIndexIndex value to uniquely identify an entry in
this table. Integer32 .1.3.6.1.2.1.10.127.7.1.9.1.1 |
docsQosServiceClassPolicyNameService Class Name to identify the name of the
service class flow to which the packet should be
directed.rw DisplayString (SNMPv2-TC) .1.3.6.1.2.1.10.127.7.1.9.1.2 |
docsQosServiceClassPolicyRulePriorityService Class Policy rule priority for the
entry.rw Integer32 .1.3.6.1.2.1.10.127.7.1.9.1.3 |
docsQosServiceClassPolicyStatusUsed to create or delete rows in this table.
This object should not be deleted if it is
reference by an entry in docsDevFilterPolicy.
The reference should be deleted first.rw RowStatus (SNMPv2-TC) .1.3.6.1.2.1.10.127.7.1.9.1.4 |
docsQosPHSTableThis table describes set of payload header
suppression entries. SEQUENCE OF DocsQosPHSEntry .1.3.6.1.2.1.10.127.7.1.10 |
docsQosPHSEntryA payload header suppression entry.
The ifIndex is an ifType of docsCableMaclayer(127).
The index docsQosServiceFlowId selects one
service flow from the cable MAC layer interface.
The docsQosPktClassId index matches an
index of the docsQosPktClassTable. DocsQosPHSEntry .1.3.6.1.2.1.10.127.7.1.10.1 |
docsQosPHSFieldPayload header suppression field defines the
bytes of the header which must be
suppressed/restored by the sending/receiving
device.
The number of octets in this object should be
the same as the value of docsQosPHSSize.ro OCTET STRING .1.3.6.1.2.1.10.127.7.1.10.1.2 |
docsQosPHSMaskPayload header suppression mask defines the
bit mask which used in combination with the
docsQosPHSField defines which bytes in header
must be suppressed/restored by the sending or
receiving device.
Each bit of this bit mask corresponds to a byte
in the docsQosPHSField, with the least
significant bit corresponding to first byte of
the docsQosPHSField.
Each bit of the bit mask specifies whether of
not the corresponding byte should be suppressed
in the packet. A bit value of '1' indicates that
the byte should be suppressed by the sending
device and restored by the receiving device.
A bit value of '0' indicates that
the byte should not be suppressed by the sending
device or restored by the receiving device.
If the bit mask does not contain a bit for each
byte in the docsQosPHSField then the bit mask is
extended with bit values of '1' to be the
necessary length.ro OCTET STRING .1.3.6.1.2.1.10.127.7.1.10.1.3 |
docsQosPHSSizePayload header suppression size specifies the
number of bytes in the header to be suppressed
and restored.
The value of this object must match the number
of bytes in the docsQosPHSField.ro Integer32 .1.3.6.1.2.1.10.127.7.1.10.1.4 |
docsQosPHSVerifyPayload header suppression verification value of
'true' the sender must verify docsQosPHSField
is the same as what is contained in the packet
to be suppressed.ro TruthValue (SNMPv2-TC) .1.3.6.1.2.1.10.127.7.1.10.1.5 |
docsQosPHSClassifierIndexThis object is obsolete.roobsolete Integer32 .1.3.6.1.2.1.10.127.7.1.10.1.6 |
docsQosPHSIndexPayload header suppression index uniquely
references the PHS rule for a given service flow.ro Integer32 .1.3.6.1.2.1.10.127.7.1.10.1.7 |
docsQosCmtsMacToSrvFlowTableThis table provide for referencing the service flows
associated with a particular cable modem. This allows
for indexing into other docsQos tables that are
indexed by docsQosServiceFlowId and ifIndex. SEQUENCE OF DocsQosCmtsMacToSrvFlowEntry .1.3.6.1.2.1.10.127.7.1.11 |
docsQosCmtsMacToSrvFlowEntryAn entry is created by CMTS for each service flow
connected to this CMTS. DocsQosCmtsMacToSrvFlowEntry .1.3.6.1.2.1.10.127.7.1.11.1 |
docsQosCmtsCmMacThe MAC address for the referenced CM. MacAddress (SNMPv2-TC) .1.3.6.1.2.1.10.127.7.1.11.1.1 |
docsQosCmtsServiceFlowIdAn index assigned to a service flow by CMTS. Unsigned32 .1.3.6.1.2.1.10.127.7.1.11.1.2 |
docsQosCmtsIfIndexThe ifIndex of ifType docsCableMacLayter(127)
on the CMTS that is connected to the Cable Modem.ro InterfaceIndex (IF-MIB) .1.3.6.1.2.1.10.127.7.1.11.1.3 |
docsQosNotification OBJECT IDENTIFIER .1.3.6.1.2.1.10.127.7.2 |
docsQosConformance OBJECT IDENTIFIER .1.3.6.1.2.1.10.127.7.3 |
docsQosGroups OBJECT IDENTIFIER .1.3.6.1.2.1.10.127.7.3.1 |
docsQosCompliances OBJECT IDENTIFIER .1.3.6.1.2.1.10.127.7.3.2 |