DOCS-IETF-RFI-MIB
This is the MIB Module for DOCSIS 2.0 compliant Radio Frequency (RF) interfaces in Cable Modems (CM) and Cable Modem Termination Systems (CMTS).
Main OID:
docsIfMib.1.3.6.1.2.1.10.127
232
Objects
Active
Status
6
Dependencies
Imported Objects
Objects
232 total| Object Name |
|---|
docsIfMibThis is the MIB Module for DOCSIS 2.0 compliant Radio Frequency (RF) interfaces in Cable Modems (CM) and Cable Modem Termination Systems (CMTS). MODULE-IDENTITY .1.3.6.1.2.1.10.127 |
docsIfMibObjects OBJECT IDENTIFIER .1.3.6.1.2.1.10.127.1 |
docsIfBaseObjects OBJECT IDENTIFIER .1.3.6.1.2.1.10.127.1.1 |
docsIfDownstreamChannelTableThis table describes the attributes of downstream channels (frequency bands). SEQUENCE OF DocsIfDownstreamChannelEntry .1.3.6.1.2.1.10.127.1.1.1 |
docsIfDownstreamChannelEntryAn entry provides a list of attributes for a single Downstream channel. An entry in this table exists for each ifEntry with an ifType of docsCableDownstream(128). DocsIfDownstreamChannelEntry .1.3.6.1.2.1.10.127.1.1.1.1 |
docsIfDownChannelIdThe Cable Modem Termination System (CMTS) identification of the downstream channel within this particular MAC interface. If the interface is down, the object returns the most current value. If the downstream channel ID is unknown, this object returns a value of 0.ro Integer32 .1.3.6.1.2.1.10.127.1.1.1.1.1 |
docsIfDownChannelFrequencyThe center of the downstream frequency associated with this channel. This object will return the current tuner frequency. If a CMTS provides IF output, this object will return 0, unless this CMTS is in control of the final downstream RF frequency. See the associated compliance object for a description of valid frequencies that may be written to this object.rw Integer32 .1.3.6.1.2.1.10.127.1.1.1.1.2 |
docsIfDownChannelWidthThe bandwidth of this downstream channel. Most implementations are expected to support a channel width of 6 MHz (North America) and/or 8 MHz (Europe). See the associated compliance object for a description of the valid channel widths for this object.rw Integer32 .1.3.6.1.2.1.10.127.1.1.1.1.3 |
docsIfDownChannelModulationThe modulation type associated with this downstream channel. If the interface is down, this object either returns the configured value (CMTS), the most current value (CM), or the value of unknown(1). See the associated conformance object for write conditions and limitations. See the reference for specifics on the modulation profiles implied by qam64 and qam256.rw Enumeration .1.3.6.1.2.1.10.127.1.1.1.1.4 |
docsIfDownChannelInterleaveThe Forward Error Correction (FEC) interleaving used for this downstream channel. Values are defined as follows: taps8Increment16(3): protection 5.9/4.1 usec, latency .22/.15 msec taps16Increment8(4): protection 12/8.2 usec, latency .48/.33 msec taps32Increment4(5): protection 24/16 usec, latency .98/.68 msec taps64Increment2(6): protection 47/33 usec, latency 2/1.4 msec taps128Increment1(7): protection 95/66 usec, latency 4/2.8 msec taps12increment17(8): protection 18/14 usec, latency 0.43/0.32 msec taps12increment17 is implemented in conformance with EuroDOCSIS document 'Adapted MIB-definitions - and a clarification for MPEG-related issues - for EuroDOCSIS cable modem systems' by tComLabs and should only be used for a EuroDOCSIS MAC interface. If the interface is down, this object either returns the configured value (CMTS), the most current value (CM), or the value of unknown(1). The value of other(2) is returned if the interleave is known but not defined in the above list. See the associated conformance object for write conditions and limitations. See the reference for the FEC configuration described by the setting of this object.rw Enumeration .1.3.6.1.2.1.10.127.1.1.1.1.5 |
docsIfDownChannelPowerAt the CMTS, the operational transmit power. At the CM, the received power level. If the interface is down, this object either returns the configured value (CMTS), the most current value (CM) or the value of 0. See the associated conformance object for write conditions and limitations. See the reference for recommended and required power levels.rw TenthdBmV UNITS "dBmV" .1.3.6.1.2.1.10.127.1.1.1.1.6 |
docsIfDownChannelAnnexThe value of this object indicates the conformance of the implementation to important regional cable standards. annexA : Annex A from ITU-J83 is used. annexB : Annex B from ITU-J83 is used. annexC : Annex C from ITU-J83 is used. AnnexB is used for DOCSIS implementationsro Enumeration .1.3.6.1.2.1.10.127.1.1.1.1.7 |
docsIfUpstreamChannelTableThis table describes the attributes of attached upstream channels. SEQUENCE OF DocsIfUpstreamChannelEntry .1.3.6.1.2.1.10.127.1.1.2 |
docsIfUpstreamChannelEntryList of attributes for a single upstream channel. For Docsis 2.0 CMTSs, an entry in this table exists for each ifEntry with an ifType of docsCableUpstreamChannel (205). For Docsis 1.x CM/CMTSs and Docsis 2.0 CMs, an entry in this table exists for each ifEntry with an ifType of docsCableUpstreamInterface (129). DocsIfUpstreamChannelEntry .1.3.6.1.2.1.10.127.1.1.2.1 |
docsIfUpChannelIdThe CMTS identification of the upstream channel.ro Integer32 .1.3.6.1.2.1.10.127.1.1.2.1.1 |
docsIfUpChannelFrequencyThe center of the frequency band associated with this upstream interface. This object returns 0 if the frequency is undefined or unknown. Minimum permitted upstream frequency is 5,000,000 Hz for current technology. See the associated conformance object for write conditions and limitations.rw Integer32 .1.3.6.1.2.1.10.127.1.1.2.1.2 |
docsIfUpChannelWidthThe bandwidth of this upstream interface. This object returns 0 if the interface width is undefined or unknown. Minimum permitted interface width is 200,000 Hz currently. See the associated conformance object for write conditions and limitations.rw Integer32 .1.3.6.1.2.1.10.127.1.1.2.1.3 |
docsIfUpChannelModulationProfileAn entry identical to the docsIfModIndex in the docsIfCmtsModulationTable that describes this channel. This channel is further instantiated there by a grouping of interval usage codes which together fully describe the channel modulation. This object returns 0 if the docsIfCmtsModulationTable entry does not exist or docsIfCmtsModulationTable is empty. See the associated conformance object for write conditions and limitations.rw Unsigned32 .1.3.6.1.2.1.10.127.1.1.2.1.4 |
docsIfUpChannelSlotSizeApplicable to TDMA and ATDMA channel types only. The number of 6.25 microsecond ticks in each upstream mini-slot. Returns zero if the value is undefined, unknown or in case of an SCDMA channel. See the associated conformance object for write conditions and limitations.rw Unsigned32 .1.3.6.1.2.1.10.127.1.1.2.1.5 |
docsIfUpChannelTxTimingOffsetAt the CM, a measure of the current round trip time obtained from the ranging offset (initial ranging offset + ranging offset adjustments). At the CMTS, the maximum of timing offset, among all the CMs that are/were present on the channel, taking into account all ( initial + periodic ) timing offset corrections that were sent for each of the CMs. Generally, these measurements are positive, but if the measurements are negative, the value of this object is zero. Used for timing of CM upstream transmissions to ensure synchronized arrivals at the CMTS. Units are in terms of (6.25 microseconds/64).ro Unsigned32 .1.3.6.1.2.1.10.127.1.1.2.1.6 |
docsIfUpChannelRangingBackoffStartThe initial random backoff window to use when retrying Ranging Requests. Expressed as a power of 2. A value of 16 at the CMTS indicates that a proprietary adaptive retry mechanism is to be used. See the associated conformance object for write conditions and limitations.rw Integer32 .1.3.6.1.2.1.10.127.1.1.2.1.7 |
docsIfUpChannelRangingBackoffEndThe final random backoff window to use when retrying Ranging Requests. Expressed as a power of 2. A value of 16 at the CMTS indicates that a proprietary adaptive retry mechanism is to be used. See the associated conformance object for write conditions and limitations.rw Integer32 .1.3.6.1.2.1.10.127.1.1.2.1.8 |
docsIfUpChannelTxBackoffStartThe initial random backoff window to use when retrying transmissions. Expressed as a power of 2. A value of 16 at the CMTS indicates that a proprietary adaptive retry mechanism is to be used. See the associated conformance object for write conditions and limitations.rw Integer32 .1.3.6.1.2.1.10.127.1.1.2.1.9 |
docsIfUpChannelTxBackoffEndThe final random backoff window to use when retrying transmissions. Expressed as a power of 2. A value of 16 at the CMTS indicates that a proprietary adaptive retry mechanism is to be used. See the associated conformance object for write conditions and limitations.rw Integer32 .1.3.6.1.2.1.10.127.1.1.2.1.10 |
docsIfUpChannelScdmaActiveCodesApplicable for SCDMA channel types only. Number of active codes. Returns zero for Non-SCDMA channel types. Note that legal values from 64..128 MUST be non-prime.rw Unsigned32 (0 | 64..128) .1.3.6.1.2.1.10.127.1.1.2.1.11 |
docsIfUpChannelScdmaCodesPerSlotApplicable for SCDMA channel types only. The number of SCDMA codes per mini-slot. Returns zero if the value is undefined, unknown or in case of a TDMA or ATDMA channel.rw Integer32(0 | 2..32) .1.3.6.1.2.1.10.127.1.1.2.1.12 |
docsIfUpChannelScdmaFrameSizeApplicable for SCDMA channel types only. SCDMA Frame size in units of spreading intervals. This value returns zero for non SCDMA Profiles.rw Unsigned32 .1.3.6.1.2.1.10.127.1.1.2.1.13 |
docsIfUpChannelScdmaHoppingSeedApplicable for SCDMA channel types only. 15 bit seed used for code hopping sequence initialization. Returns zero for non-SCDMA channel types.rw Unsigned32 .1.3.6.1.2.1.10.127.1.1.2.1.14 |
docsIfUpChannelTypeDefines the Upstream channel type. Given the channel type, other channel attributes can be checked for value validity at the time of entry creation and update.rw DocsisUpstreamType .1.3.6.1.2.1.10.127.1.1.2.1.15 |
docsIfUpChannelCloneFromIntended for use when a temporary inactive upstream table row is created for the purpose of manipulating SCDMA parameters for an active row. Refer to the descriptions of docsIfUpChannelStatus and docsIfUpChannelUpdate for details of this procedure. This object contains the ifIndex value of the active upstream row whose SCDMA parameters are to be adjusted. Although this object was created to facilitate SCDMA parameter adjustment, it may also be used at the vendor's discretion for non-SCDMA parameter adjustment. This object must contain a value of zero for active upstream rows.rw InterfaceIndexOrZero (IF-MIB) .1.3.6.1.2.1.10.127.1.1.2.1.16 |
docsIfUpChannelUpdateUsed to perform the transfer of adjusted SCDMA parameters from the temporary upstream row to the active upstream row indicated by the docsIfUpChannelCloneFrom object. The transfer is initiated through an SNMP SET of TRUE to this object. The SNMP SET will fail with a GEN_ERROR (snmpv1) or COMMIT_FAILED_ERROR (snmpv2c/v3) if the adjusted SCDMA parameter values are not compatible with each other. Although this object was created to facilitate SCDMA parameter adjustment, it may also be used at the vendor's discretion for non-SCDMA parameter adjustment. An SNMP GET of this object always returns FALSE.rw TruthValue (SNMPv2-TC) .1.3.6.1.2.1.10.127.1.1.2.1.17 |
docsIfUpChannelStatusThis object is generally intended to be used for the creation of a temporary inactive upstream row for the purpose of adjusting the SCDMA channel parameters of an active upstream row. The recommended procedure is: 1) Create an inactive row through an SNMP SET using createAndWait(5). Use an ifIndex value outside the operational range of the system. 2) Set the docsIfUpChannelCloneFrom field to the ifIndex value of the active row whose SCDMA parameters require adjustment. 3) Adjust the SCDMA parameter values using the new temporary inactive row. 4) Update the active row by setting object docsIfUpChannelUpdate to TRUE. This SET will fail if the adjusted SCDMA parameters are not compatible with each other. 5) Delete the temporary row through an SNMP SET using DELETE. The following restrictions apply to this object: 1) This object must contain a value of active(1) for active rows. 2) Temporary inactive rows must be created using createAndWait(5). 3) The only possible status change of a row created using createAndWait(5) (ie notInService(2)) is to destroy(6). These temporary rows must never become active. 4) A status transition from active (1) to destroy (6) is not permitted. Entries with docsIfUpChannelStatus set to active(1) are logically linked to a physical interface, not temporarily created to clone parameters. The Interface MIB [RFC2863] ifAdminStatus should be used to take an Upstream Channel offline. Although this object was created to facilitate SCDMA parameter adjustment, it may also be used at the vendor's discretion for non-SCDMA parameter adjustment.rw RowStatus (SNMPv2-TC) .1.3.6.1.2.1.10.127.1.1.2.1.18 |
docsIfUpChannelPreEqEnableAt the CMTS, used to enable or disable pre-equalization on the upstream channel represented by this table instance. At the CM, this object is read-only and reflects the status of pre-equalization as represented in the RNG-RSP.rw TruthValue (SNMPv2-TC) .1.3.6.1.2.1.10.127.1.1.2.1.19 |
docsIfQosProfileTableDescribes the attributes for each class of service. SEQUENCE OF DocsIfQosProfileEntry .1.3.6.1.2.1.10.127.1.1.3 |
docsIfQosProfileEntryDescribes the attributes for a single class of service. If implemented as read-create in the Cable Modem Termination System, creation of entries in this table is controlled by the value of docsIfCmtsQosProfilePermissions. If implemented as read-only, entries are created based on information in REG-REQ MAC messages received from Cable Modems (Cable Modem Termination System implementation), or based on information extracted from the TFTP option file (Cable Modem implementation). In the Cable Modem Termination system, read-only entries are removed if no longer referenced by docsIfCmtsServiceTable. An entry in this table must not be removed while it is referenced by an entry in docsIfCmServiceTable (Cable Modem) or docsIfCmtsServiceTable (Cable Modem Termination System). An entry in this table should not be changeable while it is referenced by an entry in docsIfCmtsServiceTable. If this table is created automatically, there should only be a single entry for each Class of Service. Multiple entries with the same Class of Service parameters are not recommended. DocsIfQosProfileEntry .1.3.6.1.2.1.10.127.1.1.3.1 |
docsIfQosProfIndexThe index value that uniquely identifies an entry in the docsIfQosProfileTable. Integer32 .1.3.6.1.2.1.10.127.1.1.3.1.1 |
docsIfQosProfPriorityA relative priority assigned to this service when allocating bandwidth. Zero indicates lowest priority and seven indicates highest priority. Interpretation of priority is device-specific. MUST NOT be changed while this row is active.rw Integer32 .1.3.6.1.2.1.10.127.1.1.3.1.2 |
docsIfQosProfMaxUpBandwidthThe maximum upstream bandwidth, in bits per second, allowed for a service with this service class. Zero if there is no restriction of upstream bandwidth. MUST NOT be changed while this row is active.rw Integer32 .1.3.6.1.2.1.10.127.1.1.3.1.3 |
docsIfQosProfGuarUpBandwidthMinimum guaranteed upstream bandwidth, in bits per second, allowed for a service with this service class. MUST NOT be changed while this row is active.rw Integer32 .1.3.6.1.2.1.10.127.1.1.3.1.4 |
docsIfQosProfMaxDownBandwidthThe maximum downstream bandwidth, in bits per second, allowed for a service with this service class. Zero if there is no restriction of downstream bandwidth. MUST NOT be changed while this row is active.rw Integer32 .1.3.6.1.2.1.10.127.1.1.3.1.5 |
docsIfQosProfMaxTxBurstThe maximum number of mini-slots that may be requested for a single upstream transmission. A value of zero means there is no limit. MUST NOT be changed while this row is active. This object has been deprecated and replaced by docsIfQosProfMaxTransmitBurst, to fix a mismatch of the units and value range with respect to the DOCSIS Maximum Upstream Channel Transmit Burst Configuration Setting.rwdeprecated Integer32 .1.3.6.1.2.1.10.127.1.1.3.1.6 |
docsIfQosProfBaselinePrivacyIndicates whether Baseline Privacy is enabled for this service class. MUST NOT be changed while this row is active.rw TruthValue (SNMPv2-TC) .1.3.6.1.2.1.10.127.1.1.3.1.7 |
docsIfQosProfStatusThis is object is to used to create or delete rows in this table. This object MUST NOT be changed from active while the row is referenced by the any entry in either docsIfCmServiceTable (on the CM), or the docsIfCmtsServiceTable (on the CMTS).rw RowStatus (SNMPv2-TC) .1.3.6.1.2.1.10.127.1.1.3.1.8 |
docsIfQosProfMaxTransmitBurstThe maximum number of bytes that may be requested for a single upstream transmission. A value of zero means there is no limit. Note: This value does not include any physical layer overhead. MUST NOT be changed while this row is active.rw Integer32 .1.3.6.1.2.1.10.127.1.1.3.1.9 |
docsIfSignalQualityTableAt the CM, describes the PHY signal quality of downstream channels. At the CMTS, describes the PHY signal quality of upstream channels. At the CMTS, this table may exclude contention intervals. SEQUENCE OF DocsIfSignalQualityEntry .1.3.6.1.2.1.10.127.1.1.4 |
docsIfSignalQualityEntryAt the CM, describes the PHY characteristics of a downstream channel. At the CMTS, describes the PHY signal quality of an upstream channel. An entry in this table exists for each ifEntry with an ifType of docsCableDownstream(128) for Cable Modems. For Docsis 1.1 Cable Modem Termination Systems, an entry exists for each ifEntry with an ifType of docsCableUpstream (129). For Docsis 2.0 Cable Modem Termination Systems, an entry exists for each ifEntry with an ifType of docsCableUpstreamChannel (205). DocsIfSignalQualityEntry .1.3.6.1.2.1.10.127.1.1.4.1 |
docsIfSigQIncludesContentiontrue(1) if this CMTS includes contention intervals in the counters in this table. Always false(2) for CMs.ro TruthValue (SNMPv2-TC) .1.3.6.1.2.1.10.127.1.1.4.1.1 |
docsIfSigQUnerroredsCodewords received on this channel without error. This includes all codewords, whether or not they were part of frames destined for this device.ro Counter32 .1.3.6.1.2.1.10.127.1.1.4.1.2 |
docsIfSigQCorrectedsCodewords received on this channel with correctable errors. This includes all codewords, whether or not they were part of frames destined for this device.ro Counter32 .1.3.6.1.2.1.10.127.1.1.4.1.3 |
docsIfSigQUncorrectablesCodewords received on this channel with uncorrectable errors. This includes all codewords, whether or not they were part of frames destined for this device.ro Counter32 .1.3.6.1.2.1.10.127.1.1.4.1.4 |
docsIfSigQSignalNoiseSignal/Noise ratio as perceived for this channel. At the CM, describes the Signal/Noise of the downstream channel. At the CMTS, describes the average Signal/Noise of the upstream channel.ro TenthdB UNITS "dB" .1.3.6.1.2.1.10.127.1.1.4.1.5 |
docsIfSigQMicroreflectionsTotal microreflections including in-channel response as perceived on this interface, measured in dBc below the signal level. This object is not assumed to return an absolutely accurate value, but should give a rough indication of microreflections received on this interface. It is up to the implementer to provide information as accurate as possible.ro Integer32 .1.3.6.1.2.1.10.127.1.1.4.1.6 |
docsIfSigQEqualizationDataAt the CM, returns the equalization data for the downstream channel. At the CMTS, returns the average equalization data for the upstream channel. Returns an empty string if the value is unknown or if there is no equalization data available or defined.ro OCTET STRING .1.3.6.1.2.1.10.127.1.1.4.1.7 |
docsIfSigQExtUnerroredsCodewords received on this channel without error. This includes all codewords, whether or not they were part of frames destined for this device. This is the 64 bit version of docsIfSigQUnerroreds.ro Counter64 .1.3.6.1.2.1.10.127.1.1.4.1.8 |
docsIfSigQExtCorrectedsCodewords received on this channel with correctable errors. This includes all codewords, whether or not they were part of frames destined for this device. This is the 64 bit version of docsIfSigQCorrecteds.ro Counter64 .1.3.6.1.2.1.10.127.1.1.4.1.9 |
docsIfSigQExtUncorrectablesCodewords received on this channel with uncorrectable errors. This includes all codewords, whether or not they were part of frames destined for this device. This is the 64 bit version of docsIfSigQUncorrectables.ro Counter64 .1.3.6.1.2.1.10.127.1.1.4.1.10 |
docsIfDocsisBaseCapabilityIndication of the DOCSIS capability of the device. This object mirrors docsIfDocsisCapability from the DocsIfExt mib.ro DocsisVersion .1.3.6.1.2.1.10.127.1.1.5 |
docsIfCmObjects OBJECT IDENTIFIER .1.3.6.1.2.1.10.127.1.2 |
docsIfCmMacTableDescribes the attributes of each CM MAC interface, extending the information available from ifEntry. SEQUENCE OF DocsIfCmMacEntry .1.3.6.1.2.1.10.127.1.2.1 |
docsIfCmMacEntryAn entry containing objects describing attributes of each MAC entry, extending the information in ifEntry. An entry in this table exists for each ifEntry with an ifType of docsCableMaclayer(127). DocsIfCmMacEntry .1.3.6.1.2.1.10.127.1.2.1.1 |
docsIfCmCmtsAddressIdentifies the CMTS that is believed to control this MAC domain. At the CM, this will be the source address from SYNC, MAP, and other MAC-layer messages. If the CMTS is unknown, returns 00-00-00-00-00-00.ro MacAddress (SNMPv2-TC) .1.3.6.1.2.1.10.127.1.2.1.1.1 |
docsIfCmCapabilitiesIdentifies the capabilities of the MAC implementation at this interface. Note that packet transmission is always supported. Therefore, there is no specific bit required to explicitly indicate this capability. Note that BITS objects are encoded most significant bit first. For example, if bit 1 is set, the value of this object is the octet string '40'H.ro Bits .1.3.6.1.2.1.10.127.1.2.1.1.2 |
docsIfCmRangingRespTimeoutWaiting time for a Ranging Response packet.rwobsolete TimeTicks (SNMPv2-SMI) .1.3.6.1.2.1.10.127.1.2.1.1.3 |
docsIfCmRangingTimeoutWaiting time for a Ranging Response packet.rw TimeInterval (SNMPv2-TC) .1.3.6.1.2.1.10.127.1.2.1.1.4 |
docsIfCmStatusTableThis table maintains a number of status objects and counters for Cable Modems. SEQUENCE OF DocsIfCmStatusEntry .1.3.6.1.2.1.10.127.1.2.2 |
docsIfCmStatusEntryA set of status objects and counters for a single MAC layer instance in a Cable Modem. An entry in this table exists for each ifEntry with an ifType of docsCableMaclayer(127). DocsIfCmStatusEntry .1.3.6.1.2.1.10.127.1.2.2.1 |
docsIfCmStatusValueCurrent Cable Modem connectivity state, as specified in the RF Interface Specification. Interpretations for state values 1-12 are clearly outlined in the SP-RFI reference given below. As stated in the description for object docsIfCmtsCmStatusValue, accessDenied(13)indicates the CMTS has sent a Registration Aborted message to the CM.ro Enumeration .1.3.6.1.2.1.10.127.1.2.2.1.1 |
docsIfCmStatusCodeStatus code for this Cable Modem as defined in the OSSI Specification. The status code consists of a single character indicating error groups, followed by a two- or three-digit number indicating the status condition, followed by a decimal.ro OCTET STRING .1.3.6.1.2.1.10.127.1.2.2.1.2 |
docsIfCmStatusTxPowerThe operational transmit power for the attached upstream channel.ro TenthdBmV UNITS "dBmV" .1.3.6.1.2.1.10.127.1.2.2.1.3 |
docsIfCmStatusResetsNumber of times the CM reset or initialized this interface.ro Counter32 .1.3.6.1.2.1.10.127.1.2.2.1.4 |
docsIfCmStatusLostSyncsNumber of times the CM lost synchronization with the downstream channel.ro Counter32 .1.3.6.1.2.1.10.127.1.2.2.1.5 |
docsIfCmStatusInvalidMapsNumber of times the CM received invalid MAP messages.ro Counter32 .1.3.6.1.2.1.10.127.1.2.2.1.6 |
docsIfCmStatusInvalidUcdsNumber of times the CM received invalid UCD messages.ro Counter32 .1.3.6.1.2.1.10.127.1.2.2.1.7 |
docsIfCmStatusInvalidRangingResponsesNumber of times the CM received invalid ranging response messages.ro Counter32 .1.3.6.1.2.1.10.127.1.2.2.1.8 |
docsIfCmStatusInvalidRegistrationResponsesNumber of times the CM received invalid registration response messages.ro Counter32 .1.3.6.1.2.1.10.127.1.2.2.1.9 |
docsIfCmStatusT1TimeoutsNumber of times counter T1 expired in the CM.ro Counter32 .1.3.6.1.2.1.10.127.1.2.2.1.10 |
docsIfCmStatusT2TimeoutsNumber of times counter T2 expired in the CM.ro Counter32 .1.3.6.1.2.1.10.127.1.2.2.1.11 |
docsIfCmStatusT3TimeoutsNumber of times counter T3 expired in the CM.ro Counter32 .1.3.6.1.2.1.10.127.1.2.2.1.12 |
docsIfCmStatusT4TimeoutsNumber of times counter T4 expired in the CM.ro Counter32 .1.3.6.1.2.1.10.127.1.2.2.1.13 |
docsIfCmStatusRangingAbortedsNumber of times the ranging process was aborted by the CMTS.ro Counter32 .1.3.6.1.2.1.10.127.1.2.2.1.14 |
docsIfCmStatusDocsisOperModeIndication whether the device has registered using 1.0 Class of Service or 1.1 Quality of Service. An unregistered CM should indicate 1.1 QOS for a docsIfDocsisBaseCapability value of Docsis 1.1/2.0. An unregistered CM should indicate 1.0 COS for a docsIfDocsisBaseCapability value of Docsis 1.0. This object mirrors docsIfCmDocsisOperMode from the docsIfExt mib.ro DocsisQosVersion .1.3.6.1.2.1.10.127.1.2.2.1.15 |
docsIfCmStatusModulationTypeIndicates modulation type status currently used by the CM. Since this object specifically identifies PHY mode, the shared upstream channel type is not permitted.ro DocsisUpstreamTypeStatus .1.3.6.1.2.1.10.127.1.2.2.1.16 |
docsIfCmStatusEqualizationDataPre-equalization data for this CM after convolution with data indicated in the RNG-RSP. Returns an empty string if the value is unknown or if there is no equalization data available or defined. The value should be formatted as defined in the following REFERENCE.ro OCTET STRING .1.3.6.1.2.1.10.127.1.2.2.1.17 |
docsIfCmServiceTableDescribes the attributes of each upstream service queue on a CM. SEQUENCE OF DocsIfCmServiceEntry .1.3.6.1.2.1.10.127.1.2.3 |
docsIfCmServiceEntryDescribes the attributes of an upstream bandwidth service queue. An entry in this table exists for each Service ID. The primary index is an ifIndex with an ifType of docsCableMaclayer(127). DocsIfCmServiceEntry .1.3.6.1.2.1.10.127.1.2.3.1 |
docsIfCmServiceIdIdentifies a service queue for upstream bandwidth. The attributes of this service queue are shared between the CM and the CMTS. The CMTS allocates upstream bandwidth to this service queue based on requests from the CM and on the class of service associated with this queue. Integer32 .1.3.6.1.2.1.10.127.1.2.3.1.1 |
docsIfCmServiceQosProfileThe index in docsIfQosProfileTable describing the quality of service attributes associated with this particular service. If no associated entry in docsIfQosProfileTable exists, this object returns a value of zero.ro Integer32 .1.3.6.1.2.1.10.127.1.2.3.1.2 |
docsIfCmServiceTxSlotsImmedThe number of upstream mini-slots which have been used to transmit data PDUs in immediate (contention) mode. This includes only those PDUs that are presumed to have arrived at the headend (i.e., those which were explicitly acknowledged.) It does not include retransmission attempts or mini-slots used by Requests.ro Counter32 .1.3.6.1.2.1.10.127.1.2.3.1.3 |
docsIfCmServiceTxSlotsDedThe number of upstream mini-slots which have been used to transmit data PDUs in dedicated mode (i.e., as a result of a unicast Data Grant).ro Counter32 .1.3.6.1.2.1.10.127.1.2.3.1.4 |
docsIfCmServiceTxRetriesThe number of attempts to transmit data PDUs containing requests for acknowledgment that did not result in acknowledgment.ro Counter32 .1.3.6.1.2.1.10.127.1.2.3.1.5 |
docsIfCmServiceTxExceededsThe number of data PDUs transmission failures due to excessive retries without acknowledgment.ro Counter32 .1.3.6.1.2.1.10.127.1.2.3.1.6 |
docsIfCmServiceRqRetriesThe number of attempts to transmit bandwidth requests which did not result in acknowledgment.ro Counter32 .1.3.6.1.2.1.10.127.1.2.3.1.7 |
docsIfCmServiceRqExceededsThe number of requests for bandwidth which failed due to excessive retries without acknowledgment.ro Counter32 .1.3.6.1.2.1.10.127.1.2.3.1.8 |
docsIfCmServiceExtTxSlotsImmedThe number of upstream mini-slots which have been used to transmit data PDUs in immediate (contention) mode. This includes only those PDUs that are presumed to have arrived at the headend (i.e., those which were explicitly acknowledged.) It does not include retransmission attempts or mini-slots used by Requests.ro Counter64 .1.3.6.1.2.1.10.127.1.2.3.1.9 |
docsIfCmServiceExtTxSlotsDedThe number of upstream mini-slots which have been used to transmit data PDUs in dedicated mode (i.e., as a result of a unicast Data Grant).ro Counter64 .1.3.6.1.2.1.10.127.1.2.3.1.10 |
docsIfCmtsObjects OBJECT IDENTIFIER .1.3.6.1.2.1.10.127.1.3 |
docsIfCmtsMacTableDescribes the attributes of each CMTS MAC interface, extending the information available from ifEntry. Mandatory for all CMTS devices. SEQUENCE OF DocsIfCmtsMacEntry .1.3.6.1.2.1.10.127.1.3.1 |
docsIfCmtsMacEntryAn entry containing objects describing attributes of each MAC entry, extending the information in ifEntry. An entry in this table exists for each ifEntry with an ifType of docsCableMaclayer(127). DocsIfCmtsMacEntry .1.3.6.1.2.1.10.127.1.3.1.1 |
docsIfCmtsCapabilitiesIdentifies the capabilities of the CMTS MAC implementation at this interface. Note that packet transmission is always supported. Therefore, there is no specific bit required to explicitly indicate this capability. Note that BITS objects are encoded most significant bit first. For example, if bit 1 is set, the value of this object is the octet string '40'H.ro Bits .1.3.6.1.2.1.10.127.1.3.1.1.1 |
docsIfCmtsSyncIntervalThe interval between CMTS transmission of successive SYNC messages at this interface.rw Integer32 .1.3.6.1.2.1.10.127.1.3.1.1.2 |
docsIfCmtsUcdIntervalThe interval between CMTS transmission of successive Upstream Channel Descriptor messages for each upstream channel at this interface.rw Integer32 .1.3.6.1.2.1.10.127.1.3.1.1.3 |
docsIfCmtsMaxServiceIdsThe maximum number of service IDs that may be simultaneously active.ro Integer32 .1.3.6.1.2.1.10.127.1.3.1.1.4 |
docsIfCmtsInsertionIntervalThe amount of time to elapse between each broadcast station maintenance grant. Broadcast station maintenance grants are used to allow new cable modems to join the network. Zero indicates that a vendor-specific algorithm is used instead of a fixed time. Maximum amount of time permitted by the specification is 2 seconds.rwobsolete TimeTicks (SNMPv2-SMI) .1.3.6.1.2.1.10.127.1.3.1.1.5 |
docsIfCmtsInvitedRangingAttemptsThe maximum number of attempts to make on invitations for ranging requests. A value of zero means the system should attempt to range forever.rw Integer32 .1.3.6.1.2.1.10.127.1.3.1.1.6 |
docsIfCmtsInsertIntervalThe amount of time to elapse between each broadcast station maintenance grant. Broadcast station maintenance grants are used to allow new cable modems to join the network. Zero indicates that a vendor-specific algorithm is used instead of a fixed time. Maximum amount of time permitted by the specification is 2 seconds.rw TimeInterval (SNMPv2-TC) .1.3.6.1.2.1.10.127.1.3.1.1.7 |
docsIfCmtsStatusTableFor the MAC layer, this group maintains a number of status objects and counters. SEQUENCE OF DocsIfCmtsStatusEntry .1.3.6.1.2.1.10.127.1.3.2 |
docsIfCmtsStatusEntryStatus entry for a single MAC layer. An entry in this table exists for each ifEntry with an ifType of docsCableMaclayer(127). DocsIfCmtsStatusEntry .1.3.6.1.2.1.10.127.1.3.2.1 |
docsIfCmtsStatusInvalidRangeReqsThis object counts invalid RNG-REQ messages received on this interface.ro Counter32 .1.3.6.1.2.1.10.127.1.3.2.1.1 |
docsIfCmtsStatusRangingAbortedsThis object counts ranging attempts that were explicitly aborted by the CMTS.ro Counter32 .1.3.6.1.2.1.10.127.1.3.2.1.2 |
docsIfCmtsStatusInvalidRegReqsThis object counts invalid REG-REQ messages received on this interface. That is, syntax, out of range parameters, or erroneous requests.ro Counter32 .1.3.6.1.2.1.10.127.1.3.2.1.3 |
docsIfCmtsStatusFailedRegReqsThis object counts failed registration attempts. Included are docsIfCmtsStatusInvalidRegReqs, authentication and class of service failures.ro Counter32 .1.3.6.1.2.1.10.127.1.3.2.1.4 |
docsIfCmtsStatusInvalidDataReqsThis object counts invalid data request messages received on this interface.ro Counter32 .1.3.6.1.2.1.10.127.1.3.2.1.5 |
docsIfCmtsStatusT5TimeoutsThis object counts the number of times counter T5 expired on this interface.ro Counter32 .1.3.6.1.2.1.10.127.1.3.2.1.6 |
docsIfCmtsCmStatusTableA set of objects in the CMTS, maintained for each Cable Modem connected to this CMTS. SEQUENCE OF DocsIfCmtsCmStatusEntry .1.3.6.1.2.1.10.127.1.3.3 |
docsIfCmtsCmStatusEntryStatus information for a single Cable Modem. An entry in this table exists for each Cable Modem that is connected to the CMTS implementing this table. DocsIfCmtsCmStatusEntry .1.3.6.1.2.1.10.127.1.3.3.1 |
docsIfCmtsCmStatusIndexIndex value to uniquely identify an entry in this table. For an individual Cable Modem, this index value should not change during CMTS uptime. Integer32 .1.3.6.1.2.1.10.127.1.3.3.1.1 |
docsIfCmtsCmStatusMacAddressMAC address of this Cable Modem. If the Cable Modem has multiple MAC addresses, this is the MAC address associated with the Cable interface.ro MacAddress (SNMPv2-TC) .1.3.6.1.2.1.10.127.1.3.3.1.2 |
docsIfCmtsCmStatusIpAddressIP address of this Cable Modem. If the Cable Modem has no IP address assigned, or the IP address is unknown, this object returns a value of 0.0.0.0. If the Cable Modem has multiple IP addresses, this object returns the IP address associated with the Cable interface. This object has been deprecated and replaced by docsIfCmtsCmStatusInetAddressType and docsIfCmtsCmStatusInetAddress, to enable IPv6 addressing in the future.rodeprecated IpAddress .1.3.6.1.2.1.10.127.1.3.3.1.3 |
docsIfCmtsCmStatusDownChannelIfIndexIfIndex of the downstream channel this CM is connected to. If the downstream channel is unknown, this object returns a value of zero.ro InterfaceIndexOrZero (IF-MIB) .1.3.6.1.2.1.10.127.1.3.3.1.4 |
docsIfCmtsCmStatusUpChannelIfIndexIfIndex of the upstream channel this CM is connected to. If the upstream channel is unknown, this object returns a value of zero.ro InterfaceIndexOrZero (IF-MIB) .1.3.6.1.2.1.10.127.1.3.3.1.5 |
docsIfCmtsCmStatusRxPowerThe receive power as perceived for upstream data from this Cable Modem. If the receive power is unknown, this object returns a value of zero.ro TenthdBmV UNITS "dBmV" .1.3.6.1.2.1.10.127.1.3.3.1.6 |
docsIfCmtsCmStatusTimingOffsetA measure of the current round trip time for this CM. Used for timing of CM upstream transmissions to ensure synchronized arrivals at the CMTS. Units are in terms of 6.25 microseconds/(64*256). Returns zero if the value is unknown.ro Unsigned32 .1.3.6.1.2.1.10.127.1.3.3.1.7 |
docsIfCmtsCmStatusEqualizationDataEqualization data for this CM. Returns an empty string if the value is unknown or if there is no equalization data available or defined.ro OCTET STRING .1.3.6.1.2.1.10.127.1.3.3.1.8 |
docsIfCmtsCmStatusValueCurrent Cable Modem connectivity state, as specified in the RF Interface Specification. Returned status information is the CM status as assumed by the CMTS, and indicates the following events: other(1) Any state other than below. ranging(2) The CMTS has received an Initial Ranging Request message from the CM, and the ranging process is not yet complete. rangingAborted(3) The CMTS has sent a Ranging Abort message to the CM. rangingComplete(4) The CMTS has sent a Ranging Complete message to the CM. ipComplete(5) The CMTS has received a DHCP reply message and forwarded it to the CM. registrationComplete(6) The CMTS has sent a Registration Response message to the CM. accessDenied(7) The CMTS has sent a Registration Aborted message to the CM. operational(8) If Baseline Privacy is enabled for the CM, the CMTS has completed Baseline Privacy initialization. If Baseline Privacy is not enabled, equivalent to registrationComplete. The CMTS only needs to report states it is able to detect.ro Enumeration .1.3.6.1.2.1.10.127.1.3.3.1.9 |
docsIfCmtsCmStatusUnerroredsCodewords received without error from this Cable Modem.ro Counter32 .1.3.6.1.2.1.10.127.1.3.3.1.10 |
docsIfCmtsCmStatusCorrectedsCodewords received with correctable errors from this Cable Modem.ro Counter32 .1.3.6.1.2.1.10.127.1.3.3.1.11 |
docsIfCmtsCmStatusUncorrectablesCodewords received with uncorrectable errors from this Cable Modem.ro Counter32 .1.3.6.1.2.1.10.127.1.3.3.1.12 |
docsIfCmtsCmStatusSignalNoiseSignal/Noise ratio as perceived for upstream data from this Cable Modem. If the Signal/Noise is unknown, this object returns a value of zero.ro TenthdB UNITS "dB" .1.3.6.1.2.1.10.127.1.3.3.1.13 |
docsIfCmtsCmStatusMicroreflectionsTotal microreflections including in-channel response as perceived on this interface, measured in dBc below the signal level. This object is not assumed to return an absolutely accurate value, but should give a rough indication of microreflections received on this interface. It is up to the implementer to provide information as accurate as possible.ro Integer32 .1.3.6.1.2.1.10.127.1.3.3.1.14 |
docsIfCmtsCmStatusExtUnerroredsCodewords received without error from this Cable Modem.ro Counter64 .1.3.6.1.2.1.10.127.1.3.3.1.15 |
docsIfCmtsCmStatusExtCorrectedsCodewords received with correctable errors from this Cable Modem.ro Counter64 .1.3.6.1.2.1.10.127.1.3.3.1.16 |
docsIfCmtsCmStatusExtUncorrectablesCodewords received with uncorrectable errors from this Cable Modem.ro Counter64 .1.3.6.1.2.1.10.127.1.3.3.1.17 |
docsIfCmtsCmStatusDocsisRegModeIndication whether the CM has registered using 1.0 Class of Service or 1.1 Quality of Service. This object mirrors docsIfCmtsCmStatusDocsisMode from the docsIfExt mib.ro DocsisQosVersion .1.3.6.1.2.1.10.127.1.3.3.1.18 |
docsIfCmtsCmStatusModulationTypeIndicates modulation type currently used by the CM. Since this object specifically identifies PHY mode, the shared type is not permitted. If the upstream channel is unknown, this object returns a value of zero.ro DocsisUpstreamTypeStatus .1.3.6.1.2.1.10.127.1.3.3.1.19 |
docsIfCmtsCmStatusInetAddressTypeThe type of internet address of docsIfCmtsCmStatusInetAddress. If the cable modem Internet address is unassigned or unknown, then the value of this object is unknown(0).ro InetAddressType (INET-ADDRESS-MIB) .1.3.6.1.2.1.10.127.1.3.3.1.20 |
docsIfCmtsCmStatusInetAddressInternet address of this Cable Modem. If the Cable Modem has no Internet address assigned, or the Internet address is unknown, the value of this object is the empty string. If the Cable Modem has multiple Internet addresses, this object returns the Internet address associated with the Cable (i.e. RF MAC) interface.ro InetAddress (INET-ADDRESS-MIB) .1.3.6.1.2.1.10.127.1.3.3.1.21 |
docsIfCmtsServiceTableDescribes the attributes of upstream service queues in a Cable Modem Termination System. SEQUENCE OF DocsIfCmtsServiceEntry .1.3.6.1.2.1.10.127.1.3.4 |
docsIfCmtsServiceEntryDescribes the attributes of a single upstream bandwidth service queue. Entries in this table exist for each ifEntry with an ifType of docsCableMaclayer(127), and for each service queue (Service ID) within this MAC layer. Entries in this table are created with the creation of individual Service IDs by the MAC layer and removed when a Service ID is removed. DocsIfCmtsServiceEntry .1.3.6.1.2.1.10.127.1.3.4.1 |
docsIfCmtsServiceIdIdentifies a service queue for upstream bandwidth. The attributes of this service queue are shared between the Cable Modem and the Cable Modem Termination System. The CMTS allocates upstream bandwidth to this service queue based on requests from the CM and on the class of service associated with this queue. Integer32 .1.3.6.1.2.1.10.127.1.3.4.1.1 |
docsIfCmtsServiceCmStatusIndexPointer to an entry in docsIfCmtsCmStatusTable identifying the Cable Modem using this Service Queue. If multiple Cable Modems are using this Service Queue, the value of this object is zero. This object has been deprecated and replaced by docsIfCmtsServiceNewCmStatusIndex, to fix a mismatch of the value range with respect to docsIfCmtsCmStatusIndex (1..2147483647).rodeprecated Integer32 .1.3.6.1.2.1.10.127.1.3.4.1.2 |
docsIfCmtsServiceAdminStatusAllows a service class for a particular modem to be suppressed, (re-)enabled, or deleted altogether.rw Enumeration .1.3.6.1.2.1.10.127.1.3.4.1.3 |
docsIfCmtsServiceQosProfileThe index in docsIfQosProfileTable describing the quality of service attributes associated with this particular service. If no associated docsIfQosProfileTable entry exists, this object returns a value of zero.ro Integer32 .1.3.6.1.2.1.10.127.1.3.4.1.4 |
docsIfCmtsServiceCreateTimeThe value of sysUpTime when this entry was created.ro TimeStamp (SNMPv2-TC) .1.3.6.1.2.1.10.127.1.3.4.1.5 |
docsIfCmtsServiceInOctetsThe cumulative number of Packet Data octets received on this Service ID. The count does not include the size of the Cable MAC headerro Counter32 .1.3.6.1.2.1.10.127.1.3.4.1.6 |
docsIfCmtsServiceInPacketsThe cumulative number of Packet Data packets received on this Service ID.ro Counter32 .1.3.6.1.2.1.10.127.1.3.4.1.7 |
docsIfCmtsServiceNewCmStatusIndexPointer (via docsIfCmtsCmStatusIndex) to an entry in docsIfCmtsCmStatusTable identifying the Cable Modem using this Service Queue. If multiple Cable Modems are using this Service Queue, the value of this object is zero.ro Integer32 .1.3.6.1.2.1.10.127.1.3.4.1.8 |
docsIfCmtsModulationTableDescribes a modulation profile associated with one or more upstream channels. SEQUENCE OF DocsIfCmtsModulationEntry .1.3.6.1.2.1.10.127.1.3.5 |
docsIfCmtsModulationEntryDescribes a modulation profile for an Interval Usage Code for one or more upstream channels. Entries in this table are created by the operator. Initial default entries may be created at system initialization time. No individual objects have to be specified in order to create an entry in this table. Note that some objects do not have DEFVALs, but do have calculated defaults and need not be specified during row creation. There is no restriction on the changing of values in this table while their associated rows are active. DocsIfCmtsModulationEntry .1.3.6.1.2.1.10.127.1.3.5.1 |
docsIfCmtsModIndexAn index into the Channel Modulation table representing a group of Interval Usage Codes, all associated with the same channel. Integer32 .1.3.6.1.2.1.10.127.1.3.5.1.1 |
docsIfCmtsModIntervalUsageCodeAn index into the Channel Modulation table which, when grouped with other Interval Usage Codes, fully instantiate all modulation sets for a given upstream channel. Enumeration .1.3.6.1.2.1.10.127.1.3.5.1.2 |
docsIfCmtsModControlControls and reflects the status of rows in this table.rw RowStatus (SNMPv2-TC) .1.3.6.1.2.1.10.127.1.3.5.1.3 |
docsIfCmtsModTypeThe modulation type used on this channel. Returns other(1) if the modulation type is neither qpsk, qam16, qam8, qam32, qam64 or qam128. Type qam128 is used for SCDMA channels only. See the reference for the modulation profiles implied by different modulation types.rw Enumeration .1.3.6.1.2.1.10.127.1.3.5.1.4 |
docsIfCmtsModPreambleLenThe preamble length for this modulation profile in bits. Default value is the minimum needed by the implementation at the CMTS for the given modulation profile.rw Integer32 .1.3.6.1.2.1.10.127.1.3.5.1.5 |
docsIfCmtsModDifferentialEncodingSpecifies whether or not differential encoding is used on this channel.rw TruthValue (SNMPv2-TC) .1.3.6.1.2.1.10.127.1.3.5.1.6 |
docsIfCmtsModFECErrorCorrectionThe number of correctable errored bytes (t) used in forward error correction code. The value of 0 indicates no correction is employed. The number of check bytes appended will be twice this value.rw Integer32 .1.3.6.1.2.1.10.127.1.3.5.1.7 |
docsIfCmtsModFECCodewordLengthThe number of data bytes (k) in the forward error correction codeword. This object is not used if docsIfCmtsModFECErrorCorrection is zero.rw Integer32 .1.3.6.1.2.1.10.127.1.3.5.1.8 |
docsIfCmtsModScramblerSeedThe 15 bit seed value for the scrambler polynomial.rw Integer32 .1.3.6.1.2.1.10.127.1.3.5.1.9 |
docsIfCmtsModMaxBurstSizeThe maximum number of mini-slots that can be transmitted during this channel's burst time. Returns zero if the burst length is bounded by the allocation MAP rather than this profile. Default value is 0 except for shortData, where it is 8.rw Integer32 .1.3.6.1.2.1.10.127.1.3.5.1.10 |
docsIfCmtsModGuardTimeSizeThe number of symbol-times which must follow the end of this channel's burst. Default value is the minimum time needed by the implementation for this modulation profile.ro Unsigned32 .1.3.6.1.2.1.10.127.1.3.5.1.11 |
docsIfCmtsModLastCodewordShortenedIndicates if the last FEC codeword is truncated.rw TruthValue (SNMPv2-TC) .1.3.6.1.2.1.10.127.1.3.5.1.12 |
docsIfCmtsModScramblerIndicates if the scrambler is employed.rw TruthValue (SNMPv2-TC) .1.3.6.1.2.1.10.127.1.3.5.1.13 |
docsIfCmtsModByteInterleaverDepthATDMA Byte Interleaver Depth (Ir). This object returns 1 for non ATDMA profiles.rw Unsigned32 .1.3.6.1.2.1.10.127.1.3.5.1.14 |
docsIfCmtsModByteInterleaverBlockSizeATDMA Byte Interleaver Block size (Br). This object returns zero for non ATDMA profilesrw Unsigned32 .1.3.6.1.2.1.10.127.1.3.5.1.15 |
docsIfCmtsModPreambleTypePreamble type for DOCSIS 2.0 burstsrw Enumeration .1.3.6.1.2.1.10.127.1.3.5.1.16 |
docsIfCmtsModTcmErrorCorrectionOnTrellis Code Modulation (TCM) On/Off. This value returns false for non S-CDMA profiles.rw TruthValue (SNMPv2-TC) .1.3.6.1.2.1.10.127.1.3.5.1.17 |
docsIfCmtsModScdmaInterleaverStepSizeS-CDMA Interleaver step size. This value returns zero for non S-CDMA profiles.rw Unsigned32 (0 | 1..32) .1.3.6.1.2.1.10.127.1.3.5.1.18 |
docsIfCmtsModScdmaSpreaderEnableS-CDMA spreader. This value returns false for non S-CDMA profiles. Default value for IUC 3 and 4 is OFF, for all other IUCs it is ON.rw TruthValue (SNMPv2-TC) .1.3.6.1.2.1.10.127.1.3.5.1.19 |
docsIfCmtsModScdmaSubframeCodesS-CDMA sub-frame size. This value returns zero for non S-CDMA profiles.rw Unsigned32 (0 | 1..128) .1.3.6.1.2.1.10.127.1.3.5.1.20 |
docsIfCmtsModChannelTypeDescribes the modulation channel type for this modulation entry.rw DocsisUpstreamType .1.3.6.1.2.1.10.127.1.3.5.1.21 |
docsIfCmtsQosProfilePermissionsThis object specifies permitted methods of creating entries in docsIfQosProfileTable. CreateByManagement(0) is set if entries can be created using SNMP. UpdateByManagement(1) is set if updating entries using SNMP is permitted. CreateByModems(2) is set if entries can be created based on information in REG-REQ MAC messages received from Cable Modems. Information in this object is only applicable if docsIfQosProfileTable is implemented as read-create. Otherwise, this object is implemented as read-only and returns CreateByModems(2). Either CreateByManagement(0) or CreateByModems(1) must be set when writing to this object. Note that BITS objects are encoded most significant bit first. For example, if bit 2 is set, the value of this object is the octet string '20'H.rw Bits .1.3.6.1.2.1.10.127.1.3.6 |
docsIfCmtsMacToCmTableThis is a table to provide a quick access index into the docsIfCmtsCmStatusTable. There is exactly one row in this table for each row in the docsIfCmtsCmStatusTable. In general, the management station should use this table only to get a pointer into the docsIfCmtsCmStatusTable (which corresponds to the CM's RF interface MAC address), and should not iterate (e.g. GetNext through) this table. SEQUENCE OF DocsIfCmtsMacToCmEntry .1.3.6.1.2.1.10.127.1.3.7 |
docsIfCmtsMacToCmEntryA row in the docsIfCmtsMacToCmTable. An entry in this table exists for each Cable Modem that is connected to the CMTS implementing this table. DocsIfCmtsMacToCmEntry .1.3.6.1.2.1.10.127.1.3.7.1 |
docsIfCmtsCmMacThe RF side MAC address for the referenced CM. (E.g. the interface on the CM that has docsCableMacLayer(127) as its ifType. MacAddress (SNMPv2-TC) .1.3.6.1.2.1.10.127.1.3.7.1.1 |
docsIfCmtsCmPtrAn row index into docsIfCmtsCmStatusTable. When queried with the correct instance value (e.g. a CM's MAC address), returns the index in docsIfCmtsCmStatusTable which represents that CM.ro Integer32 .1.3.6.1.2.1.10.127.1.3.7.1.2 |
docsIfCmtsChannelUtilizationIntervalThe time interval in seconds over which the channel utilization index is calculated. All upstream/downstream channels use the same docsIfCmtsChannelUtilizationInterval. Setting a value of zero disables utilization reporting. A channel utilization index is calculated over a fixed window applying to the most recent docsIfCmtsChannelUtilizationInterval. It would therefore be prudent to use a relatively short docsIfCmtsChannelUtilizationInterval.rw Integer32 .1.3.6.1.2.1.10.127.1.3.8 |
docsIfCmtsChannelUtilizationTableReports utilization statistics for attached upstream and downstream physical channels. SEQUENCE OF DocsIfCmtsChannelUtilizationEntry .1.3.6.1.2.1.10.127.1.3.9 |
docsIfCmtsChannelUtilizationEntryUtilization statistics for a single upstream or downstream physical channel. An entry exists in this table for each ifEntry with an ifType equal to docsCableDownstreamInterface (128) or docsCableUpstreamInterface (129). DocsIfCmtsChannelUtilizationEntry .1.3.6.1.2.1.10.127.1.3.9.1 |
docsIfCmtsChannelUtIfTypeThe secondary index into this table. Indicates the IANA interface type associated with this physical channel. Only docsCableDownstreamInterface (128) and docsCableUpstreamInterface (129) are valid. IANAifType (IANAifType-MIB) .1.3.6.1.2.1.10.127.1.3.9.1.1 |
docsIfCmtsChannelUtIdThe tertiary index into this table. Indicates the CMTS identifier for this physical channel. Integer32 .1.3.6.1.2.1.10.127.1.3.9.1.2 |
docsIfCmtsChannelUtUtilizationThe calculated and truncated utilization index for this physical upstream or downstream channel, accurate as of the most recent docsIfCmtsChannelUtilizationInterval. Upstream Channel Utilization Index: The upstream channel utilization index is expressed as a percentage of minislots utilized on the physical channel, regardless of burst type. For an Initial Maintenance region, the minislots for the complete region are considered utilized if the CMTS received an upstream burst within the region from any CM on the physical channel. For contention REQ and REQ/DATA regions, the minislots for a transmission opportunity within the region are considered utilized if the CMTS received an upstream burst within the opportunity from any CM on the physical channel. For all other regions, utilized minislots are those in which the CMTS granted bandwidth to any unicast SID on the physical channel. For an upstream interface that has multiple logical upstream channels enabled, the utilization index is a weighted sum of utilization indices for the logical channels. The weight for each utilization index is the percentage of upstream minislots allocated for the corresponding logical channel. Example: If 75% of bandwidth is allocated to the first logical channel and 25% to the second, and the utilization indices for each are 60 and 40 respectively, the utilization index for the upstream physical channel is (60 * 0.75) + (40 * 0.25) = 55. This figure applies to the most recent utilization interval. Downstream Channel Utilization Index: The downstream channel utilization index is a percentage expressing the ratio between bytes used to transmit data versus the total number of bytes transmitted in the raw bandwidth of the MPEG channel. As with the upstream utilization index, the calculated value represents the most recent utilization interval. Formula: Downstream utilization index = (100 * (data bytes / raw bytes)) = (100 * ((raw bytes - stuffed bytes) / raw bytes)) Definitions: Data bytes: Number of bytes transmitted as data in the docsIfCmtsChannelUtilizationInterval. Identical to docsIfCmtsDownChannelCtrUsed Bytes measured over the utilization interval. Stuffed bytes: Number of filler bytes transmitted as non-data in the DocsIfCmtsChannelUtilizationInterval. Raw bandwidth: Total number of bytes available for transmitting data, not including bytes used for headers and other overhead. Raw bytes: (raw bandwidth * docsIfCmtsChannelUtilizationInterval). Identical to docsIfCmtsDownChannelCtrTotal Bytes measured over the utilization interval.ro Integer32 .1.3.6.1.2.1.10.127.1.3.9.1.3 |
docsIfCmtsDownChannelCounterTableThis table is implemented at the CMTS to collect downstream channel statistics for utilization calculations. SEQUENCE OF DocsIfCmtsDownChannelCounterEntry .1.3.6.1.2.1.10.127.1.3.10 |
docsIfCmtsDownChannelCounterEntryAn entry provides a list of traffic counters for a single downstream channel. An entry in this table exists for each ifEntry with an ifType of docsCableDownstream(128). DocsIfCmtsDownChannelCounterEntry .1.3.6.1.2.1.10.127.1.3.10.1 |
docsIfCmtsDownChnlCtrIdThe Cable Modem Termination System (CMTS) identification of the downstream channel within this particular MAC interface. If the interface is down, the object returns the most current value. If the downstream channel ID is unknown, this object returns a value of 0.ro Integer32 .1.3.6.1.2.1.10.127.1.3.10.1.1 |
docsIfCmtsDownChnlCtrTotalBytesAt the CMTS, the total number of bytes in the Payload portion of MPEG Packets (ie. not including MPEG header or pointer_field) transported by this downstream channel since CMTS initialization. This is the 32 bit version of docsIfCmtsDownChnlCtrExtTotalBytes, included to provide back compatibility with SNMPv1 managers.ro Counter32 .1.3.6.1.2.1.10.127.1.3.10.1.2 |
docsIfCmtsDownChnlCtrUsedBytesAt the CMTS, the total number of DOCSIS data bytes transported by this downstream channel since CMTS initialization. The number of data bytes is defined as the total number of bytes transported in DOCSIS payloads minus the number of stuff bytes transported in DOCSIS payloads. This is the 32 bit version of docsIfCmtsDownChnlCtrExtUsedBytes, included to provide back compatibility with SNMPv1 managers.ro Counter32 .1.3.6.1.2.1.10.127.1.3.10.1.3 |
docsIfCmtsDownChnlCtrExtTotalBytesAt the CMTS, the total number of bytes in the Payload portion of MPEG Packets (ie. not including MPEG header or pointer_field) transported by this downstream channel since CMTS initialization. This is the 64 bit version of docsIfCmtsDownChnlCtrTotalBytes, and will not be accessible to SNMPv1 managers.ro Counter64 .1.3.6.1.2.1.10.127.1.3.10.1.4 |
docsIfCmtsDownChnlCtrExtUsedBytesAt the CMTS, the total number of DOCSIS data bytes transported by this downstream channel since CMTS initialization. The number of data bytes is defined as the total number of bytes transported in DOCSIS payloads minus the number of stuff bytes transported in DOCSIS payloads. This is the 64 bit version of docsIfCmtsDownChnlCtrUsedBytes, and will not be accessible to SNMPv1 managers.ro Counter64 .1.3.6.1.2.1.10.127.1.3.10.1.5 |
docsIfCmtsUpChannelCounterTableThis table is implemented at the CMTS to provide upstream channel statistics appropriate for channel utilization calculations. SEQUENCE OF DocsIfCmtsUpChannelCounterEntry .1.3.6.1.2.1.10.127.1.3.11 |
docsIfCmtsUpChannelCounterEntryList of traffic statistics for a single upstream channel. For Docsis 2.0 CMTSs, an entry in this table exists for each ifEntry with an ifType of docsCableUpstreamChannel (205). For Docsis 1.x CMTSs, an entry in this table exists for each ifEntry with an ifType of docsCableUpstreamInterface (129). DocsIfCmtsUpChannelCounterEntry .1.3.6.1.2.1.10.127.1.3.11.1 |
docsIfCmtsUpChnlCtrIdThe CMTS identification of the upstream channel.ro Integer32 .1.3.6.1.2.1.10.127.1.3.11.1.1 |
docsIfCmtsUpChnlCtrTotalMslotsCurrent count, from CMTS initialization, of all minislots defined for this upstream logical channel. This count includes all IUCs and SIDs, even those allocated to the NULL SID for a 2.0 logical channel which is inactive. This is the 32 bit version of docsIfCmtsUpChnlCtrExtTotalMslots and is included for back compatibility with SNMPv1 managers. Support for this object is mandatory.ro Counter32 .1.3.6.1.2.1.10.127.1.3.11.1.2 |
docsIfCmtsUpChnlCtrUcastGrantedMslotsCurrent count, from CMTS initialization, of unicast granted minislots on the upstream logical channel, regardless of burst type. Unicast granted minislots are those in which the CMTS assigned bandwidth to any unicast SID on the logical channel. This is the 32 bit version of docsIfCmtsUpChnlCtrExtUcastGrantedMslots, and is included for back compatibility with SNMPv1 managers. Support for this object is mandatory.ro Counter32 .1.3.6.1.2.1.10.127.1.3.11.1.3 |
docsIfCmtsUpChnlCtrTotalCntnMslotsCurrent count, from CMTS initialization, of contention minislots defined for this upstream logical channel. This count includes all minislots assigned to a broadcast or multicast SID on the logical channel. This is the 32 bit version of docsIfCmtsUpChnlCtrExtTotalCntnMslots, and is included for back compatibility with SNMPv1 managers. Support for this object is mandatory.ro Counter32 .1.3.6.1.2.1.10.127.1.3.11.1.4 |
docsIfCmtsUpChnlCtrUsedCntnMslotsCurrent count, from CMTS initialization, of contention minislots utilized on the upstream logical channel. For contention regions, utilized minislots are those in which the CMTS correctly received an upstream burst from any CM on the upstream logical channel. This is the 32 bit version of docsIfCmtsUpChnlCtrExtUsedCntnMslots, and is included for back compatibility with SNMPv1 managers. Support for this object is mandatory.ro Counter32 .1.3.6.1.2.1.10.127.1.3.11.1.5 |
docsIfCmtsUpChnlCtrExtTotalMslotsCurrent count, from CMTS initialization, of all minislots defined for this upstream logical channel. This count includes all IUCs and SIDs, even those allocated to the NULL SID for a 2.0 logical channel which is inactive. This is the 64 bit version of docsIfCmtsUpChnlCtrTotalMslots, and will not be accessible to SNMPv1 managers. Support for this object is mandatory.ro Counter64 .1.3.6.1.2.1.10.127.1.3.11.1.6 |
docsIfCmtsUpChnlCtrExtUcastGrantedMslotsCurrent count, from CMTS initialization, of unicast granted minislots on the upstream logical channel, regardless of burst type. Unicast granted minislots are those in which the CMTS assigned bandwidth to any unicast SID on the logical channel. This is the 64 bit version of docsIfCmtsUpChnlCtrUcastGrantedMslots, and will not be accessible to SNMPv1 managers. Support for this object is mandatory.ro Counter64 .1.3.6.1.2.1.10.127.1.3.11.1.7 |
docsIfCmtsUpChnlCtrExtTotalCntnMslotsCurrent count, from CMTS initialization, of contention minislots defined for this upstream logical channel. This count includes all minislots assigned to a broadcast or multicast SID on the logical channel. This is the 64 bit version of docsIfCmtsUpChnlCtrTotalCntnMslots, and will not be accessible to SNMPv1 managers. Support for this object is mandatory.ro Counter64 .1.3.6.1.2.1.10.127.1.3.11.1.8 |
docsIfCmtsUpChnlCtrExtUsedCntnMslotsCurrent count, from CMTS initialization, of contention minislots utilized on the upstream logical channel. For contention regions, utilized minislots are those in which the CMTS correctly received an upstream burst from any CM on the upstream logical channel. This is the 64 bit version of docsIfCmtsUpChnlCtrUsedCntnMslots, and will not be accessible to SNMPv1 managers. Support for this object is mandatory.ro Counter64 .1.3.6.1.2.1.10.127.1.3.11.1.9 |
docsIfCmtsUpChnlCtrCollCntnMslotsCurrent count, from CMTS initialization, of contention minislots subjected to collisions on the upstream logical channel. For contention regions, these are the minislots applicable to bursts that the CMTS detected, but could not correctly receive. This is the 32 bit version of docsIfCmtsUpChnlCtrExtCollCntnMslots, and is included for back compatibility with SNMPv1 managers. Support for this object is optional. If the object is not supported, a value of zero is returned.ro Counter32 .1.3.6.1.2.1.10.127.1.3.11.1.10 |
docsIfCmtsUpChnlCtrTotalCntnReqMslotsCurrent count, from CMTS initialization, of contention request minislots defined for this upstream logical channel. This count includes all minislots for IUC1 assigned to a broadcast or multicast SID on the logical channel. This is the 32 bit version of docsIfCmtsUpChnlCtrExtTotalCntnReqMslots, and is included for back compatibility with SNMPv1 managers. Support for this object is optional. If the object is not supported, a value of zero is returned.ro Counter32 .1.3.6.1.2.1.10.127.1.3.11.1.11 |
docsIfCmtsUpChnlCtrUsedCntnReqMslotsCurrent count, from CMTS initialization, of contention request minislots utilized on this upstream logical channel. This count includes all contention minislots for IUC1 applicable to bursts that the CMTS correctly received. This is the 32 bit version of docsIfCmtsUpChnlCtrExtUsedCntnReqMslots, and is included for back compatibility with SNMPv1 managers. Support for this object is optional. If the object is not supported, a value of zero is returned.ro Counter32 .1.3.6.1.2.1.10.127.1.3.11.1.12 |
docsIfCmtsUpChnlCtrCollCntnReqMslotsCurrent count, from CMTS initialization, of contention request minislots subjected to collisions on this upstream logical channel. This includes all contention minislots for IUC1 applicable to bursts that the CMTS detected, but could not correctly receive. This is the 32 bit version of docsIfCmtsUpChnlCtrExtCollCntnReqMslots, and is included for back compatibility with SNMPv1 managers. Support for this object is optional. If the object is not supported, a value of zero is returned.ro Counter32 .1.3.6.1.2.1.10.127.1.3.11.1.13 |
docsIfCmtsUpChnlCtrTotalCntnReqDataMslotsCurrent count, from CMTS initialization, of contention request data minislots defined for this upstream logical channel. This count includes all minislots for IUC2 assigned to a broadcast or multicast SID on the logical channel. This is the 32 bit version of docsIfCmtsUpChnlCtrExtTotalCntnReqDataMslots, and is included for back compatibility with SNMPv1 managers. Support for this object is optional. If the object is not supported, a value of zero is returned.ro Counter32 .1.3.6.1.2.1.10.127.1.3.11.1.14 |
docsIfCmtsUpChnlCtrUsedCntnReqDataMslotsCurrent count, from CMTS initialization, of contention request data minislots utilized on this upstream logical channel. This includes all contention minislots for IUC2 applicable to bursts that the CMTS correctly received. This is the 32 bit version of docsIfCmtsUpChnlCtrExtUsedCntnReqDataMslots, and is included for back compatibility with SNMPv1 managers. Support for this object is optional. If the object is not supported, a value of zero is returned.ro Counter32 .1.3.6.1.2.1.10.127.1.3.11.1.15 |
docsIfCmtsUpChnlCtrCollCntnReqDataMslotsCurrent count, from CMTS initialization, of contention request data minislots subjected to collisions on this upstream logical channel. This includes all contention minislots for IUC2 applicable to bursts that the CMTS detected, but could not correctly receive. This is the 32 bit version of docsIfCmtsUpChnlCtrExtCollCntnReqDataMslots, and is included for back compatibility with SNMPv1 managers. Support for this object is optional. If the object is not supported, a value of zero is returned.ro Counter32 .1.3.6.1.2.1.10.127.1.3.11.1.16 |
docsIfCmtsUpChnlCtrTotalCntnInitMaintMslotsCurrent count, from CMTS initialization, of contention initial maintenance minislots defined for this upstream logical channel. This includes all minislots for IUC3 assigned to a broadcast or multicast SID on the logical channel. This is the 32 bit version of docsIfCmtsUpChnlCtrExtTotalCntnInitMaintMslots, and is included for back compatibility with SNMPv1 managers. Support for this object is optional. If the object is not supported, a value of zero is returned.ro Counter32 .1.3.6.1.2.1.10.127.1.3.11.1.17 |
docsIfCmtsUpChnlCtrUsedCntnInitMaintMslotsCurrent count, from CMTS initialization, of contention initial maintenance minislots utilized on this upstream logical channel. This includes all contention minislots for IUC3 applicable to bursts that the CMTS correctly received. This is the 32 bit version of docsIfCmtsUpChnlCtrExtUsedCntnInitMaintMslots, and is included for back compatibility with SNMPv1 managers. Support for this object is optional. If the object is not supported, a value of zero is returned.ro Counter32 .1.3.6.1.2.1.10.127.1.3.11.1.18 |
docsIfCmtsUpChnlCtrCollCntnInitMaintMslotsCurrent count, from CMTS initialization, of contention initial maintenance minislots subjected to collisions on this upstream logical channel. This includes all contention minislots for IUC3 applicable to bursts that the CMTS detected, but could not correctly receive. This is the 32 bit version of docsIfCmtsUpChnlCtrExtCollCntnInitMaintMslots, and is included for back compatibility with SNMPv1 managers. Support for this object is optional. If the object is not supported, a value of zero is returned.ro Counter32 .1.3.6.1.2.1.10.127.1.3.11.1.19 |
docsIfCmtsUpChnlCtrExtCollCntnMslotsCurrent count, from CMTS initialization, of collision contention minislots on the upstream logical channel. For contention regions, these are the minislots applicable to bursts that the CMTS detected, but could not correctly receive. This is the 64 bit version of docsIfCmtsUpChnlCtrCollCntnMslots, and will not be accessible to SNMPv1 managers. Support for this object is optional. If the object is not supported, a value of zero is returned.ro Counter64 .1.3.6.1.2.1.10.127.1.3.11.1.20 |
docsIfCmtsUpChnlCtrExtTotalCntnReqMslotsCurrent count, from CMTS initialization, of contention request minislots defined for this upstream logical channel. This count includes all minislots for IUC1 assigned to a broadcast or multicast SID on the logical channel. This is the 64 bit version of docsIfCmtsUpChnlCtrTotalCntnReqMslots, and will not be accessible to SNMPv1 managers. Support for this object is optional. If the object is not supported, a value of zero is returned.ro Counter64 .1.3.6.1.2.1.10.127.1.3.11.1.21 |
docsIfCmtsUpChnlCtrExtUsedCntnReqMslotsCurrent count, from CMTS initialization, of contention request minislots utilized on this upstream logical channel. This count includes all contention minislots for IUC1 applicable to bursts that the CMTS correctly received. This is the 64 bit version of docsIfCmtsUpChnlCtrUsedCntnReqMslots, and will not be accessible to SNMPv1 managers. Support for this object is optional. If the object is not supported, a value of zero is returned.ro Counter64 .1.3.6.1.2.1.10.127.1.3.11.1.22 |
docsIfCmtsUpChnlCtrExtCollCntnReqMslotsCurrent count, from CMTS initialization, of contention request minislots subjected to collisions on this upstream logical channel. This includes all contention minislots for IUC1 applicable to bursts that the CMTS detected, but could not correctly receive. This is the 64 bit version of docsIfCmtsUpChnlCtrCollCntnReqMslots, and will not be accessible to SNMPv1 managers. Support for this object is optional. If the object is not supported, a value of zero is returned.ro Counter64 .1.3.6.1.2.1.10.127.1.3.11.1.23 |
docsIfCmtsUpChnlCtrExtTotalCntnReqDataMslotsCurrent count, from CMTS initialization, of contention request data minislots defined for this upstream logical channel. This count includes all minislots for IUC2 assigned to a broadcast or multicast SID on the logical channel. This is the 64 bit version of docsIfCmtsUpChnlCtrTotalCntnReqDataMslots, and will not be accessible to SNMPv1 managers. Support for this object is optional. If the object is not supported, a value of zero is returned.ro Counter64 .1.3.6.1.2.1.10.127.1.3.11.1.24 |
docsIfCmtsUpChnlCtrExtUsedCntnReqDataMslotsCurrent count, from CMTS initialization, of contention request data minislots utilized on this upstream logical channel. This includes all contention minislots for IUC2 applicable to bursts that the CMTS correctly received. This is the 64 bit version of docsIfCmtsUpChnlCtrUsedCntnReqDataMslots, and will not be accessible to SNMPv1 managers. Support for this object is optional. If the object is not supported, a value of zero is returned.ro Counter64 .1.3.6.1.2.1.10.127.1.3.11.1.25 |
docsIfCmtsUpChnlCtrExtCollCntnReqDataMslotsCurrent count, from CMTS initialization, of contention request data minislots subjected to collisions on this upstream logical channel. This includes all contention minislots for IUC2 applicable to bursts that the CMTS detected, but could not correctly receive. This is the 64 bit version of docsIfCmtsUpChnlCtrCollCntnReqDataMslots, and will not be accessible to SNMPv1 managers. Support for this object is optional. If the object is not supported, a value of zero is returned.ro Counter64 .1.3.6.1.2.1.10.127.1.3.11.1.26 |
docsIfCmtsUpChnlCtrExtTotalCntnInitMaintMslotsCurrent count, from CMTS initialization, of initial maintenance minislots defined for this upstream logical channel. This count includes all minislots for IUC3 assigned to a broadcast or multicast SID on the logical channel. This is the 64 bit version of docsIfCmtsUpChnlCtrTotalCntnInitMaintMslots, and will not be accessible to SNMPv1 managers. Support for this object is optional. If the object is not supported, a value of zero is returned.ro Counter64 .1.3.6.1.2.1.10.127.1.3.11.1.27 |
docsIfCmtsUpChnlCtrExtUsedCntnInitMaintMslotsCurrent count, from CMTS initialization, of initial maintenance minislots utilized on this upstream logical channel. This includes all contention minislots for IUC3 applicable to bursts that the CMTS correctly received. This is the 64 bit version of docsIfCmtsUpChnlCtrUsedCntnInitMaintMslots, and will not be accessible to SNMPv1 managers. Support for this object is optional. If the object is not supported, a value of zero is returned.ro Counter64 .1.3.6.1.2.1.10.127.1.3.11.1.28 |
docsIfCmtsUpChnlCtrExtCollCntnInitMaintMslotsCurrent count, from CMTS initialization, of contention initial maintenance minislots subjected to collisions on this upstream logical channel. This includes all contention minislots for IUC3 applicable to bursts that the CMTS detected, but could not correctly receive. This is the 64 bit version of docsIfCmtsUpChnlCtrCollCntnInitMaintMslots, and will not be accessible to SNMPv1 managers. Support for this object is optional. If the object is not supported, a value of zero is returned.ro Counter64 .1.3.6.1.2.1.10.127.1.3.11.1.29 |
docsIfNotification OBJECT IDENTIFIER .1.3.6.1.2.1.10.127.2 |
docsIfConformance OBJECT IDENTIFIER .1.3.6.1.2.1.10.127.3 |
docsIfCompliances OBJECT IDENTIFIER .1.3.6.1.2.1.10.127.3.1 |
docsIfBasicComplianceThe compliance statement for devices that implement MCNS/DOCSIS compliant Radio Frequency Interfaces. Unknown .1.3.6.1.2.1.10.127.3.1.1 |
docsIfGroups OBJECT IDENTIFIER .1.3.6.1.2.1.10.127.3.2 |
docsIfBasicGroupGroup of objects implemented in both Cable Modems and Cable Modem Termination Systems. Unknown .1.3.6.1.2.1.10.127.3.2.1 |
docsIfCmGroupGroup of objects implemented in Cable Modems. Unknown .1.3.6.1.2.1.10.127.3.2.2 |
docsIfCmtsGroupGroup of objects implemented in Cable Modem Termination Systems. Unknown .1.3.6.1.2.1.10.127.3.2.3 |
docsIfCompliancesV2 OBJECT IDENTIFIER .1.3.6.1.2.1.10.127.3.3 |
docsIfBasicComplianceV2The compliance statement for devices that implement MCNS/DOCSIS compliant Radio Frequency Interfaces. Unknown .1.3.6.1.2.1.10.127.3.3.1 |
docsIfGroupsV2 OBJECT IDENTIFIER .1.3.6.1.2.1.10.127.3.4 |
docsIfBasicGroupV2Group of objects implemented in both Cable Modems and Cable Modem Termination Systems. Unknown .1.3.6.1.2.1.10.127.3.4.1 |
docsIfCmGroupV2Group of objects implemented in Cable Modems. Unknown .1.3.6.1.2.1.10.127.3.4.2 |
docsIfCmtsGroupV2Group of objects implemented in Cable Modem Termination Systems. Unknown .1.3.6.1.2.1.10.127.3.4.3 |