DLINKSW-CABLE-DIAG-MIB
AI MIB Summary
The DLINKSW-CABLE-DIAG-MIB enables D-Link switch management systems to monitor physical layer cable integrity and link status via SNMP, specifically tracking diagnostic parameters such as cable length, attenuation, and fault detection for attached copper or fiber interfaces.
The MIB module for determining the status of the cables attached to the device.
Main OID:
dlinkSwCableDiagMIB.1.3.6.1.4.1.171.14.58
22
Objects
Active
Status
5
Dependencies
Imported Objects
Objects
22 total| Object Name |
|---|
dlinkSwCableDiagMIBThe MIB module for determining the status of the cables attached to the device. MODULE-IDENTITY .1.3.6.1.4.1.171.14.58 |
dCableDiagNotifications OBJECT IDENTIFIER .1.3.6.1.4.1.171.14.58.0 |
dCableDiagObjects OBJECT IDENTIFIER .1.3.6.1.4.1.171.14.58.1 |
dCableDiagIfTableA table contains a list of information about test on the device's interfaces. Note that entries will exist in this table when the corresponding interface is capable to run test. SEQUENCE OF DCableDiagIfEntry .1.3.6.1.4.1.171.14.58.1.1 |
dCableDiagIfEntryAn entry in the dCableDiagIfTable, contains the testing controls on an interface. DCableDiagIfEntry .1.3.6.1.4.1.171.14.58.1.1.1 |
dCableDiagIfActionThis object control the action to be executed on the interface. noOp(1) - No action is taken if this object is set to 'noOp'. When read, the value 'noOp' is returned. test(2) - Start the test on the interface. clear(3) - Clear all the test results on the interface. The value of the following objects of the entry will become 'other'. -- dCableDiagResultPair1Status -- dCableDiagResultPair2Status -- dCableDiagResultPair3Status -- dCableDiagResultPair4Status The value of the following objects of the entry will become -1 (unavailable) -- dCableDiagResultPair1Length -- dCableDiagResultPair2Length -- dCableDiagResultPair3Length -- dCableDiagResultPair4Length The value of dCableDiagResultStatus of the entry will become 'notRun'.rw Enumeration .1.3.6.1.4.1.171.14.58.1.1.1.1 |
dCableDiagResultTableA table contains a list of interface's cable situation. Note that entries will exist in this table when the corresponding interface is a copper Ethernet port. SEQUENCE OF DCableDiagResultEntry .1.3.6.1.4.1.171.14.58.1.2 |
dCableDiagResultEntryAn entry in dCableDiagResultTable contains cable situation of an interface. DCableDiagResultEntry .1.3.6.1.4.1.171.14.58.1.2.1 |
dCableDiagResultPair1StatusThis object indicates the status of pair 1 of the cable.ro DlinkCableDiagStatus .1.3.6.1.4.1.171.14.58.1.2.1.1 |
dCableDiagResultPair2StatusThis object indicates the status of pair 2 of the cable.ro DlinkCableDiagStatus .1.3.6.1.4.1.171.14.58.1.2.1.2 |
dCableDiagResultPair3StatusThis object indicates the status of pair 3 of the cable.ro DlinkCableDiagStatus .1.3.6.1.4.1.171.14.58.1.2.1.3 |
dCableDiagResultPair4StatusThis object indicates the status of pair 4 of the cable.ro DlinkCableDiagStatus .1.3.6.1.4.1.171.14.58.1.2.1.4 |
dCableDiagResultPair1LengthThis object indicates the approximate length or length to the failure of pair 1 of the cable. This value is in meter units. The special value of -1 indicates the length is unavailable.ro Integer32 UNITS "meters" .1.3.6.1.4.1.171.14.58.1.2.1.5 |
dCableDiagResultPair2LengthThis object indicates the approximate length or length to the failure of pair 2 of the cable. This value is in meter units. The special value of -1 indicates the length is unavailable.ro Integer32 UNITS "meters" .1.3.6.1.4.1.171.14.58.1.2.1.6 |
dCableDiagResultPair3LengthThis object indicates the approximate length or length to the failure of pair 3 of the cable. This value is in meter units. The special value of -1 indicates the length is unavailable.ro Integer32 UNITS "meters" .1.3.6.1.4.1.171.14.58.1.2.1.7 |
dCableDiagResultPair4LengthThis object indicates the approximate length or length to the failure of pair 4 of the cable. This value is in meter units. The special value of -1 indicates the length is unavailable.ro Integer32 UNITS "meters" .1.3.6.1.4.1.171.14.58.1.2.1.8 |
dCableDiagResultStatusIndicates the status of cable diagnostics on the interface. notRun(0) - the cable diagnostics has never been run for this interface or the previous result is cleared. processing(1) - the cable diagnostics is currently running on the interface. lastTestOk(2) - the last cable diagnostics was performed successfully on the interface. lastTestFailed(3) - the last cable diagnostics failed on the interface.ro Enumeration .1.3.6.1.4.1.171.14.58.1.2.1.9 |
dCableDiagConformance OBJECT IDENTIFIER .1.3.6.1.4.1.171.14.58.2 |
dCableDiagCompliances OBJECT IDENTIFIER .1.3.6.1.4.1.171.14.58.2.1 |
dCableDiagComplianceThe compliance statement for entities which implement the DLINKSW-CABLE-DIAG-MIB. Unknown .1.3.6.1.4.1.171.14.58.2.1.1 |
dCableDiagGroups OBJECT IDENTIFIER .1.3.6.1.4.1.171.14.58.2.1.2 |
dCableDiagBasicGroupThis group contains the collection of objects related to configuration and information of fundamental cable diagnostics feature. Unknown .1.3.6.1.4.1.171.14.58.2.1.2.1 |