DLINKPRIME-CABLE-DIAG-MIB
AI MIB Summary
The DLINKPRIME-CABLE-DIAG-MIB enables monitoring of physical layer connectivity status and diagnostic parameters for attached coaxial cables on D-Link Prime cable modems. It provides specific metrics for cable signal integrity, including attenuation levels, noise margins, and link state validation to facilitate fault isolation in DOCSIS-based access networks.
The MIB module for determining the status of the cables attached to the device.
Main OID:
dlinkPrimeCableDiagMIB.dlinkPrimeCommon.1
15
Objects
Active
Status
5
Dependencies
Imported Objects
Objects
15 total| Object Name |
|---|
dlinkPrimeCableDiagMIBThe MIB module for determining the status of
the cables attached to the device. MODULE-IDENTITY .dlinkPrimeCommon.1 |
dpCableDiagNotifications OBJECT IDENTIFIER .dlinkPrimeCommon.1.0 |
dpCableDiagObjects OBJECT IDENTIFIER .dlinkPrimeCommon.1.1 |
dpCableDiagIfTableA table contains a list of information about test on the device's
interfaces. Note that entries will exist in this table when the
corresponding interface is capable to run test. SEQUENCE OF DpCableDiagIfEntry .dlinkPrimeCommon.1.1.1 |
dpCableDiagIfEntryAn entry in the dpCableDiagIfTable, contains the
testing controls on an interface. DpCableDiagIfEntry .dlinkPrimeCommon.1.1.1.1 |
dpCableDiagIfActionThis object control the action to be executed on the interface.
noOp(1) - No action is taken if this object is set to 'noOp'.
When read, the value 'noOp' is returned.
test(2) - Start the test on the interface.
clear(3) - Clear all the test results on the interface.
The value of the following objects of the entry will
become 'other'.
The value of the following objects of the entry will
become -1 (unavailable)
The value of dpCableDiagResultStatus of the entry will
become 'notRun'.rw Enumeration .dlinkPrimeCommon.1.1.1.1.1 |
dpCableDiagResultTableA table contains a list of interface's cable situation.
Note that entries will exist in this table when the
corresponding interface is a copper Ethernet port. SEQUENCE OF DpCableDiagResultEntry .dlinkPrimeCommon.1.1.2 |
dpCableDiagResultEntryAn entry in dpCableDiagResultTable contains cable situation
of an interface. DpCableDiagResultEntry .dlinkPrimeCommon.1.1.2.1 |
dpCableDiagResultCableStatusThe status of a pair of the cable.
no_result(0) - The cable have not do cable daig or result have
been clear.
ok(1) - The pair or cable has no error.
noCable(2) - The port does not have any cable connection to the
remote partner.
open(3) - The cable in the error pair does not have a connection
at the specified position.
short(4) - The cable in the error pair has a short problem at the
specified position.
openOrShort(5) - The PHY has no capability to distinguish between
open and short state.
crosstalk(6)- The cable in the error pair has a crosstalk problem
at the specified position.ro Enumeration .dlinkPrimeCommon.1.1.2.1.1 |
dpCableDiagResultCableLengthThis object indicates the approximate length or length to the failure of
the cable. This value is in meter units.
The special value of -1 indicates the length is unavailable.ro Integer32 UNITS "meters" .dlinkPrimeCommon.1.1.2.1.2 |
dpCableDiagLinkStatusThe current link operational state of the interface.ro Enumeration .dlinkPrimeCommon.1.1.2.1.3 |
dpCableDiagInterfaceTypeThe current port type of the interface.ro Enumeration .dlinkPrimeCommon.1.1.2.1.4 |
dpCableDiagConformance OBJECT IDENTIFIER .dlinkPrimeCommon.1.2 |
dpCableDiagCompliances OBJECT IDENTIFIER .dlinkPrimeCommon.1.2.1 |
dpCableDiagGroups OBJECT IDENTIFIER .dlinkPrimeCommon.1.2.1.2 |