DLINK-3100-BRGMACSWITCH-MIB
The DLINK-3100-BRGMACSWITCH-MIB enables monitoring and management of MAC address table entries, forwarding statistics, and switching parameters on D-Link 3100 series bridge and switch devices via SNMP. It provides access to vendor-specific metrics for troubleshooting Layer 2 connectivity, analyzing traffic flows, and verifying port-based MAC learning states on D-Link hardware.
Imported Objects
Objects
12 total| Object Name |
|---|
rlBrgMacSwitchThis private MIB module defines Switching Parameters private MIBs. MODULE-IDENTITY .1.3.6.1.4.1.171.10.94.89.89.50 |
rlBrgMacSwVersionMIB's version, the current version is 2.ro INTEGER .1.3.6.1.4.1.171.10.94.89.89.50.1 |
rlBrgMacSwMaxTableNumberMaximum number of MAC Tables supported by the device.ro INTEGER .1.3.6.1.4.1.171.10.94.89.89.50.2 |
rlBrgMacSwDynamicTablesSpecifies whether the device supports port dynamic MAC tables.ro Enumeration .1.3.6.1.4.1.171.10.94.89.89.50.3 |
rlBrgMacSwOldEntryDeleteModeThe method used to delete old unused entries refresh_flag: The high level sets a flag when it adds or updates an entry, the Switch clears the flag each time, when it learns the station once more. aging_flag: The high level clears a flag when it adds or updates an entry, the Switch sets the flag each time, when it learns the station once more. aging_time: The high level defines a timeout, the Switch sends a message to the high level each time when the station doesn't send messages during interval between timeout and 2*timeout. Boundaries: The Switch doesn't support any mechanism, and the high level uses two boundaries: red and yellow. When the number of entries exceeds the red boundary, the high level deletes the oldest entries.ro Enumeration .1.3.6.1.4.1.171.10.94.89.89.50.5 |
rlBrgMacSwSpanningTreeSpecifies whether the device supports port the Spanning Tree Protocol.ro Enumeration .1.3.6.1.4.1.171.10.94.89.89.50.6 |
rlBrgMacSwKeyTypeSpecified the used MAC Address Table kye format: macOnly: One global MAC Address Table per device (leaky VLANs). tagAndMac: MAC Address Table per each VLAN (strick VLANs).ro Enumeration .1.3.6.1.4.1.171.10.94.89.89.50.7 |
rlBrgMacSwYellowBoundaryThe yellow boundary.rw INTEGER .1.3.6.1.4.1.171.10.94.89.89.50.8 |
rlBrgMacSwRedBoundaryThe yellow boundary.rw INTEGER .1.3.6.1.4.1.171.10.94.89.89.50.9 |
rlBrgMacSwTrapEnableThis variable indicates whether to create a SNMP trap if adding dynamic mac failed due to full hash chain.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.171.10.94.89.89.50.10 |
rlBrgMacSwOperTrapCountThis variable indicates the trap counter status (i.e. number of received MAC addresses since the last trap sent that haven't been inserted into the hash). It is relevant only when trap is enabled.ro INTEGER .1.3.6.1.4.1.171.10.94.89.89.50.11 |
rlBrgMacSwAdminTrapFrequencyThis variable indicates the minimal frequency (in seconds) of sending a trap. It is relevant only when trap is enabled.rw INTEGER (1 .. 86400) -- UNITS "seconds" .1.3.6.1.4.1.171.10.94.89.89.50.12 |
More MIBs from D-Link
Browse all D-LinkMIBs →SNMP MIB module
The DGS-1210-12TSME-BX MIB module provides management capabilities for the D-Link DES-1210-52ME switch, specifically enabling the monitoring and configuration of QinQ (802.1ad) VLAN encapsulation parameters, including inner tag insertion and drop counters for unmatched traffic. This module facilitates precise control over service provider bridging (SPB) operations by exposing metrics related to VLAN tag manipulation and packet discard events on the device's managed ports.
SNMP MIB module
Standard SNMP MIB module defining data structures for DGS-1210-28PME_AX.
Standard SNMP MIB module defining data structures for DGS-1210-28ME_AX.
Standard SNMP MIB module defining data structures for DGS-1210-20ME_AX.