DGS3224-SWL3MGMT-MIB
The Structure of Layer 3 Network Management Information for the proprietary enterprise.
Main OID:
swL3MgmtMIB.1.3.6.1.4.1.171.11.101.3.3
45
Objects
Active
Status
4
Dependencies
Imported Objects
Objects
45 total| Object Name |
|---|
swL3MgmtMIBThe Structure of Layer 3 Network Management Information for the proprietary enterprise. MODULE-IDENTITY .1.3.6.1.4.1.171.11.101.3.3 |
swL3IpMgmt OBJECT IDENTIFIER .1.3.6.1.4.1.171.11.101.3.3.2 |
swL3IpCtrlMgmt OBJECT IDENTIFIER .1.3.6.1.4.1.171.11.101.3.3.2.1 |
swL3IpCtrlTableThis table contains IP interface information. SEQUENCE OF SwL3IpCtrlEntry .1.3.6.1.4.1.171.11.101.3.3.2.1.3 |
swL3IpCtrlEntryA list of information about a specific IP interface. SwL3IpCtrlEntry .1.3.6.1.4.1.171.11.101.3.3.2.1.3.1 |
swL3IpCtrlInterfaceNameThis object indicates the name of the IP interface.ro DisplayString .1.3.6.1.4.1.171.11.101.3.3.2.1.3.1.1 |
swL3IpCtrlIfIndexThis object uniquely identifies the IP interface number in the swL3IpCtrlTable.ro INTEGER .1.3.6.1.4.1.171.11.101.3.3.2.1.3.1.2 |
swL3IpCtrlIpAddrThe IP address of the interface. This object only can take the value of the unicast IP address.rw IpAddress .1.3.6.1.4.1.171.11.101.3.3.2.1.3.1.3 |
swL3IpCtrlIpSubnetMaskThe IP net mask for this interface.rw IpAddress .1.3.6.1.4.1.171.11.101.3.3.2.1.3.1.4 |
swL3IpCtrlVlanNameThis object indicates the IP control entry's VLAN name. The VLAN name in each entry must be unique in the IP Control Table.rw DisplayString .1.3.6.1.4.1.171.11.101.3.3.2.1.3.1.5 |
swL3IpCtrlModeThis object indicates the IP operation mode. other(1) - This entry is currently in use but the conditions under which it will remain are determined by each of the following values. bootp(3) - The IP address will be set automatically from a BOOTP server. dhcp(4) - The IP address will be set automatically from a DHCP server.rw Enumeration .1.3.6.1.4.1.171.11.101.3.3.2.1.3.1.8 |
swL3IpCtrlAdminStateThe state of the IP interface.rw Enumeration .1.3.6.1.4.1.171.11.101.3.3.2.1.3.1.9 |
swL3IpCtrlIpv6LinkLocalAddressThe IPv6 link local address for this interface.ro Ipv6Address .1.3.6.1.4.1.171.11.101.3.3.2.1.3.1.14 |
swL3IpCtrlIpv6LinkLocalPrefixLenThe IPv6 prefix length for this IPv6 link local address.ro INTEGER .1.3.6.1.4.1.171.11.101.3.3.2.1.3.1.15 |
swL3IpCtrlStateThis variable displays the status of the entry. The status is used for creating, modifying, and deleting instances of the objects in this table.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.171.11.101.3.3.2.1.3.1.16 |
swL3IpCtrlIpv6LinkLocalAutoStateThe state of the IPv6 link local auto.rw Enumeration .1.3.6.1.4.1.171.11.101.3.3.2.1.3.1.17 |
swL3IpCtrlDhcpv6ClientStateThe object indicates the state of the DHCPv6 client.rw Enumeration .1.3.6.1.4.1.171.11.101.3.3.2.1.3.1.20 |
swL3IpCtrlIpDhcpOption12StateEnable or disable insertion of option 12 in the DHCPDISCOVER and DHCPREQUEST message.rw Enumeration .1.3.6.1.4.1.171.11.101.3.3.2.1.3.1.22 |
swL3IpCtrlIpDhcpOption12HostNameSpecify the host name to be inserted in the DHCPDISCOVER and DHCPREQUEST message. The specified host name must start with a letter, end with a letter or digit, and have only letters, digits, and hyphen as interior characters; the maximal length is 63. By default, the host name is empty. When set an empty host name, means to clear the host name setting and use the default value to encode option 12.rw DisplayString .1.3.6.1.4.1.171.11.101.3.3.2.1.3.1.23 |
swL3Ipv6CtrlTableThis table contains IPv6 information of an IP interface. SEQUENCE OF SwL3Ipv6CtrlEntry .1.3.6.1.4.1.171.11.101.3.3.2.1.4 |
swL3Ipv6CtrlEntryA list of IPv6 information about a specific IP interface. SwL3Ipv6CtrlEntry .1.3.6.1.4.1.171.11.101.3.3.2.1.4.1 |
swL3Ipv6CtrlInterfaceNameThis object indicates the name of the IP interface.ro DisplayString .1.3.6.1.4.1.171.11.101.3.3.2.1.4.1.1 |
swL3Ipv6CtrlMaxReassmblySizeMaximum Reassembly Size of the IP interface.ro INTEGER .1.3.6.1.4.1.171.11.101.3.3.2.1.4.1.2 |
swL3Ipv6CtrlNsRetransTimerNeighbor solicitation's retransmit timer. The unit is set in milliseconds.rw Unsigned32 .1.3.6.1.4.1.171.11.101.3.3.2.1.4.1.3 |
swL3Ipv6CtrlRaStateNeighbor solicited state.rw Enumeration .1.3.6.1.4.1.171.11.101.3.3.2.1.4.1.5 |
swL3Ipv6CtrlRaMinRtrAdvIntervalThe minimum time allowed between sending unsolicited multicast Router Advertisements from the interface. The unit is set in seconds. It must be no less than 3 seconds and no greater than .75 * MaxRtrAdvInterval. Default value: 0.33 * MaxRtrAdvIntervalrw INTEGER .1.3.6.1.4.1.171.11.101.3.3.2.1.4.1.6 |
swL3Ipv6CtrlRaMaxRtrAdvIntervalThe maximum time allowed between sending unsolicited multicast Router Advertisements from the interface. The unit is set in seconds.rw INTEGER .1.3.6.1.4.1.171.11.101.3.3.2.1.4.1.7 |
swL3Ipv6CtrlRaLifeTimeIndicates the lifetime of the router as the default router.rw INTEGER .1.3.6.1.4.1.171.11.101.3.3.2.1.4.1.8 |
swL3Ipv6CtrlRaReachableTimeIndicates the amount of time that a node can consider a neighboring node reachable after receiving a reachability confirmation.rw INTEGER .1.3.6.1.4.1.171.11.101.3.3.2.1.4.1.9 |
swL3Ipv6CtrlRaRetransTimeIndicates the amount of time between retransmissions of neighbor solicited messages. The unit is set in millisecond.rw Unsigned32 .1.3.6.1.4.1.171.11.101.3.3.2.1.4.1.10 |
swL3Ipv6CtrlRaHopLimitIndicates the default value of the hop limit field in the IPv6 header for packets sent by hosts that receive this RA message.rw INTEGER .1.3.6.1.4.1.171.11.101.3.3.2.1.4.1.11 |
swL3Ipv6CtrlRaManagedFlagWhen enabled, it indicates that hosts receiving this RA must use a stateful address configuration protocol to obtain an address in the addition to the addresses derived from the stateless address configuration.rw Enumeration .1.3.6.1.4.1.171.11.101.3.3.2.1.4.1.12 |
swL3Ipv6CtrlRaOtherConfigFlagWhen enabled, it indicates that hosts receiving this RA must use a stateful address configuration protocol to obtain an on-link address configuration information.rw Enumeration .1.3.6.1.4.1.171.11.101.3.3.2.1.4.1.13 |
swL3Ipv6AddressCtrlTableThis table contains IPv6 address information for each IP interface. SEQUENCE OF SwL3Ipv6AddressCtrlEntry .1.3.6.1.4.1.171.11.101.3.3.2.1.5 |
swL3Ipv6AddressCtrlEntryA list of information about a specific IPv6 address. SwL3Ipv6AddressCtrlEntry .1.3.6.1.4.1.171.11.101.3.3.2.1.5.1 |
swL3Ipv6AddressCtrlInterfaceNameThis object indicates the name of the IP interface.ro DisplayString .1.3.6.1.4.1.171.11.101.3.3.2.1.5.1.1 |
swL3Ipv6AddressSpecify the IPv6 address.ro Ipv6Address .1.3.6.1.4.1.171.11.101.3.3.2.1.5.1.2 |
swL3Ipv6AddressCtrlPrefixLenIndicates the prefix length of this IPv6 address.ro INTEGER .1.3.6.1.4.1.171.11.101.3.3.2.1.5.1.3 |
swL3Ipv6AddressCtrlPreferredLifeTimeIndicates the number of seconds that an address, based on the specified prefix, using the stateless address configuration, remains in preferred state. For an infinite valid lifetime, the value can be set to 0xffffffff.rw Unsigned32 .1.3.6.1.4.1.171.11.101.3.3.2.1.5.1.4 |
swL3Ipv6AddressCtrlValidLifeTimeIndicates the number of seconds that an address, based on the specified prefix, using the stateless address configuration, remains valid. For an infinite valid lifetime, the value can be set to 0xffffffff.rw Unsigned32 .1.3.6.1.4.1.171.11.101.3.3.2.1.5.1.5 |
swL3Ipv6AddressCtrlOnLinkFlagWhen enabled, the address implied by the specified prefix is available on the link where the RA message is received.rw Enumeration .1.3.6.1.4.1.171.11.101.3.3.2.1.5.1.6 |
swL3Ipv6AddressCtrlAutonomousFlagWhen enabled, the specified prefix will be used to create an autonomous address configuration.rw Enumeration .1.3.6.1.4.1.171.11.101.3.3.2.1.5.1.7 |
swL3Ipv6AddressCtrlStateThis variable displays the status of the entry. The status is used for creating, modifying, and deleting instances of the objects in this table.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.171.11.101.3.3.2.1.5.1.8 |
swL3Ipv6AddressCtrlAddressTypeThis object indicates the type of the IPv6 address. manual(1): the IPv6 address is configured by user. dhcpv6(2): the IPv6 address is assigned by DHCPv6 server. stateless(3): the IPv6 address is assigned by router advertisement.ro Enumeration .1.3.6.1.4.1.171.11.101.3.3.2.1.5.1.9 |
swL3IpCtrlAllIpIfStateThis object indicates all interface function state of the device.rw Enumeration .1.3.6.1.4.1.171.11.101.3.3.2.1.7 |