DGS3200-L2MGMT-MIB
The Structure of Layer 2 Network Management Information.
Main OID:
swL2MgmtMIB.1.3.6.1.4.1.171.11.101.1.2
272
Objects
Active
Status
4
Dependencies
Imported Objects
Objects
272 total| Object Name |
|---|
swL2MgmtMIBThe Structure of Layer 2 Network Management Information. MODULE-IDENTITY .1.3.6.1.4.1.171.11.101.1.2 |
swL2DevMgmt OBJECT IDENTIFIER .1.3.6.1.4.1.171.11.101.1.2.1 |
swL2DevInfo OBJECT IDENTIFIER .1.3.6.1.4.1.171.11.101.1.2.1.1 |
swDevInfoTotalNumOfPortThe number of ports within this switch. This value is the sum of the ports within this switch.ro INTEGER .1.3.6.1.4.1.171.11.101.1.2.1.1.1 |
swDevInfoNumOfPortInUseThe number of ports in this switch connected to the segment or the end stations.ro INTEGER .1.3.6.1.4.1.171.11.101.1.2.1.1.2 |
swDevInfoFrontPanelLedStatusThis object is a set of system LED indications. The first four octets are defined as system LED. The first two octets are currently unused and must be set to zero. The third octet indicates the power LED. The fourth octet indicates the console LED. The fifth LED is RPS (Redundancy Power Supply) LED. The other octets are the logical port LED. Every two bytes are presented to a port. The first byte is presented as the Link/Activity LED. The second byte is presented as the Speed LED. System LED: 01 = fail/error/non existence. 02 = work normal Link/Activity LED : The most significant bit is used for blink/solid: 8 = The LED blinks. The second most significant bit is used for link status: 1 = link fail. 2 = link pass. Speed LED : 01 = 10Mbps. 02 = 100Mbps. 03 = 1000Mbps. The four remaining bits are currently unused and must be 0.ro OCTET STRING .1.3.6.1.4.1.171.11.101.1.2.1.1.4 |
swL2DevCtrl OBJECT IDENTIFIER .1.3.6.1.4.1.171.11.101.1.2.1.2 |
swL2DevCtrlStpStateThis object can enable or disable the spanning tree algorithm during the runtime of the system.rw Enumeration .1.3.6.1.4.1.171.11.101.1.2.1.2.1 |
swL2DevCtrlIGMPSnoopingThis object indicates if the layer 2 Internet Group Management Protocol (IGMP) capture function is enabled or disabled.rw Enumeration .1.3.6.1.4.1.171.11.101.1.2.1.2.2 |
swL2DevCtrlRmonStateThis object can enable or disable RMON.rw Enumeration .1.3.6.1.4.1.171.11.101.1.2.1.2.4 |
swL2DevCtrlSnmpTrapStateThis object controls the SNMP trap status.rw Enumeration .1.3.6.1.4.1.171.11.101.1.2.1.2.5 |
swL2DevCtrlCleanAllStatisticCounterWhen the object is set to active, all statistical counters will be cleared. If set to normal, no action.rw Enumeration .1.3.6.1.4.1.171.11.101.1.2.1.2.6 |
swL2DevCtrlVlanIdOfFDBTblIndicates the VLAN ID to which the Dot1dTpFdbTable belongs; The default value is DEFAULT-VLAN-ID of the system.rw VlanId .1.3.6.1.4.1.171.11.101.1.2.1.2.7 |
swL2MACNotifyStateThis object can enable or disable MAC Notification.rw Enumeration .1.3.6.1.4.1.171.11.101.1.2.1.2.8 |
swL2MACNotifyHistorySizeThis object indicates the history size of MAC addresses in the MAC Address table. The default value is 1 .rw INTEGER .1.3.6.1.4.1.171.11.101.1.2.1.2.9 |
swL2MACNotifyIntervalThis object indicates the time interval, in seconds, which will trigger MAC notification messages.rw INTEGER .1.3.6.1.4.1.171.11.101.1.2.1.2.10 |
swL2DevCtrlTelnet OBJECT IDENTIFIER .1.3.6.1.4.1.171.11.101.1.2.1.2.14 |
swL2DevCtrlTelnetStateThis object controls the Telnet status.rw Enumeration .1.3.6.1.4.1.171.11.101.1.2.1.2.14.1 |
swL2DevCtrlTelnetTcpPortThis object designates TCP ports. When Telnet is disabled, this object is not accessible.rw INTEGER .1.3.6.1.4.1.171.11.101.1.2.1.2.14.2 |
swL2DevCtrlManagementVlanIdThis object controls which previously created VLANs are included in the System IP Interface.rw VlanId .1.3.6.1.4.1.171.11.101.1.2.1.2.16 |
swL2DevCtrlWeb OBJECT IDENTIFIER .1.3.6.1.4.1.171.11.101.1.2.1.2.17 |
swL2DevCtrlWebStateThis object controls the Web status.rw Enumeration .1.3.6.1.4.1.171.11.101.1.2.1.2.17.1 |
swL2DevCtrlWebTcpPortThis object designates TCP ports. When Web is disabled, this object is not accessible.rw INTEGER .1.3.6.1.4.1.171.11.101.1.2.1.2.17.2 |
swL2DevCtrlLLDPStateSpecifies the state of the LLDP function. When this function is enabled, the switch can start to transmit LLDP packets and receive and process the LLDP packets. The specific function of each port will depend on the per port LLDP setting. For the advertisement of LLDP packets, the switch announces the information to its neighbor through ports. For the receiving of LLDP packets, the switch will learn the information from the LLDP packets advertised from the neighbor in the neighbor table.rw Enumeration .1.3.6.1.4.1.171.11.101.1.2.1.2.18 |
swL2DevCtrlLLDPForwardMessageStateWhen lldp is disabled and lldp forward-message is enabled, the received LLDP Data Unit packets will be forwarded.rw Enumeration .1.3.6.1.4.1.171.11.101.1.2.1.2.19 |
swL2DevCtrlIpAutoconfigThis object controls the IP auto configuration state.rw Enumeration .1.3.6.1.4.1.171.11.101.1.2.1.2.20 |
swL2DevCtrlCFM OBJECT IDENTIFIER .1.3.6.1.4.1.171.11.101.1.2.1.2.21 |
swL2DevCtrlCFMStateThis object indicates the CFM global state.rw Enumeration .1.3.6.1.4.1.171.11.101.1.2.1.2.21.1 |
swL2DevCtrlCFMPortTableA table containing the CFM state of specified ports. SEQUENCE OF SwL2DevCtrlCFMPortEntry .1.3.6.1.4.1.171.11.101.1.2.1.2.21.2 |
swL2DevCtrlCFMPortEntryThe entry of the CFM state on specified ports. SwL2DevCtrlCFMPortEntry .1.3.6.1.4.1.171.11.101.1.2.1.2.21.2.1 |
swL2DevCtrlCFMPortIndexThis object indicates the port number. INTEGER .1.3.6.1.4.1.171.11.101.1.2.1.2.21.2.1.1 |
swL2DevCtrlCFMPortStateThis object indicates the CFM state by port.rw Enumeration .1.3.6.1.4.1.171.11.101.1.2.1.2.21.2.1.2 |
swL2DevCtrlVLANTrunkStateThis indicates the global state of the VLAN trunking feature of the device.rw Enumeration .1.3.6.1.4.1.171.11.101.1.2.1.2.22 |
swL2DevAlarm OBJECT IDENTIFIER .1.3.6.1.4.1.171.11.101.1.2.1.3 |
swL2DevAlarmNewRootWhen the device has become the new root of the Spanning Tree, this object decides whether to send a new root trap.rw Enumeration .1.3.6.1.4.1.171.11.101.1.2.1.3.1 |
swL2DevAlarmTopologyChangeThis object determines whether or not to send a trap message when the switch topology changes. If the object is enabled(3), the topologyChange trap is sent by the device when any of its configured ports transitions from the Learning state to the Forwarding state, or from the Forwarding state to the Blocking state. For the same port transition, the device does not send the trap if this object value is disabled or other.rw Enumeration .1.3.6.1.4.1.171.11.101.1.2.1.3.2 |
swL2DevAlarmLinkChangeThis object determines whether or not to send a trap message when the link was changed. If the object is enabled(3), the Link Change trap is sent by the device when any of its ports link change. The device does not send the trap if this object value is disabled or other.rw Enumeration .1.3.6.1.4.1.171.11.101.1.2.1.3.3 |
swL2VLANMgmt OBJECT IDENTIFIER .1.3.6.1.4.1.171.11.101.1.2.2 |
swL2VlanStaticTableA table containing static configuration information for each VLAN configured into the device by (local or network) management. All entries are permanent and will be restored after the device is reset. SEQUENCE OF SwL2VlanStaticEntry .1.3.6.1.4.1.171.11.101.1.2.2.1 |
swL2VlanStaticEntryStatic information for a VLAN configured into the device by (local or network) management. SwL2VlanStaticEntry .1.3.6.1.4.1.171.11.101.1.2.2.1.1 |
swL2VlanIndexThe VLAN-ID or other identifier referring to this VLAN. VlanId .1.3.6.1.4.1.171.11.101.1.2.2.1.1.1 |
swL2VLANAdvertisementThis object indicates if the advertisement is active or not.rw Enumeration .1.3.6.1.4.1.171.11.101.1.2.2.1.1.2 |
swL2PVIDAutoAssignmentStateThis object controls the PVID auto assigment state. If 'Auto-assign PVID' is disabled, PVID only be changed by PVID configuration (user changes explicitly). The VLAN configuration will not automatically change PVID. If 'Auto-assign PVID' is enabled, PVID will be possibly changed by PVID or VLAN configuration. When user configures a port to VLAN X's untagged membership, this port's PVID will be updated with VLAN X. In the form of VLAN list command, PVID is updated with last item of VLAN list. When user removes a port from the untagged membership of the PVID's VLAN, the port's PVID will be assigned with 'default VLAN'.rw Enumeration .1.3.6.1.4.1.171.11.101.1.2.2.2 |
swL2VlanPortInfoTableA table containing vlan and port role information of each port. SEQUENCE OF SwL2VlanPortInfoEntry .1.3.6.1.4.1.171.11.101.1.2.2.3 |
swL2VlanPortInfoEntryThe table entry of vlan port information. SwL2VlanPortInfoEntry .1.3.6.1.4.1.171.11.101.1.2.2.3.1 |
swL2VlanPortInfoPortIndexThe port index.ro INTEGER .1.3.6.1.4.1.171.11.101.1.2.2.3.1.1 |
swL2VlanPortInfoVidThe VLAN-ID assigned to a special portro INTEGER .1.3.6.1.4.1.171.11.101.1.2.2.3.1.2 |
swL2VlanPortInfoPortRoleThe port role of a special port.when none,it means this port is not belong to the vlan.ro Enumeration .1.3.6.1.4.1.171.11.101.1.2.2.3.1.3 |
swL2PortMgmt OBJECT IDENTIFIER .1.3.6.1.4.1.171.11.101.1.2.3 |
swL2PortInfoTableA table that contains information about every port. SEQUENCE OF SwL2PortInfoEntry .1.3.6.1.4.1.171.11.101.1.2.3.1 |
swL2PortInfoEntryA list of information for each port of the device. SwL2PortInfoEntry .1.3.6.1.4.1.171.11.101.1.2.3.1.1 |
swL2PortInfoPortIndexThis object indicates the module's port number.(1..Max port number in the module)ro INTEGER .1.3.6.1.4.1.171.11.101.1.2.3.1.1.1 |
swL2PortInfoMediumTypeIndicates medium type of the port number.ro Enumeration .1.3.6.1.4.1.171.11.101.1.2.3.1.1.2 |
swL2PortInfoUnitIDIndicates ID of the unit in the systemro INTEGER .1.3.6.1.4.1.171.11.101.1.2.3.1.1.3 |
swL2PortInfoTypeThis object indicates the connector type of this port.ro Enumeration .1.3.6.1.4.1.171.11.101.1.2.3.1.1.4 |
swL2PortInfoLinkStatusThis object indicates the port link status.ro Enumeration .1.3.6.1.4.1.171.11.101.1.2.3.1.1.5 |
swL2PortInfoNwayStatusThis object indicates the port speed and duplex mode.ro Enumeration .1.3.6.1.4.1.171.11.101.1.2.3.1.1.6 |
swL2PortInfoErrorDisabledThis object indicates the blocking type of this port.ro Enumeration .1.3.6.1.4.1.171.11.101.1.2.3.1.1.8 |
swL2PortCtrlTableA table that contains control information about every port. SEQUENCE OF SwL2PortCtrlEntry .1.3.6.1.4.1.171.11.101.1.2.3.2 |
swL2PortCtrlEntryA list of control information for each port of the device. SwL2PortCtrlEntry .1.3.6.1.4.1.171.11.101.1.2.3.2.1 |
swL2PortCtrlPortIndexThis object indicates the module's port number.(1..Max port number in the module)ro INTEGER .1.3.6.1.4.1.171.11.101.1.2.3.2.1.1 |
swL2PortCtrlMediumTypeIndicates medium type of the port number.ro Enumeration .1.3.6.1.4.1.171.11.101.1.2.3.2.1.2 |
swL2PortCtrlUnitIndexIndicates ID of the unit in the devicero INTEGER .1.3.6.1.4.1.171.11.101.1.2.3.2.1.3 |
swL2PortCtrlAdminStateThis object decides if the port is enabled or disabled.rw Enumeration .1.3.6.1.4.1.171.11.101.1.2.3.2.1.4 |
swL2PortCtrlNwayStateChose the port speed, duplex mode, and N-Way function mode.rw Enumeration .1.3.6.1.4.1.171.11.101.1.2.3.2.1.5 |
swL2PortCtrlFlowCtrlStateThe flow control mechanism is different between full duplex mode and half duplex mode. For half duplex mode, the jamming signal is asserted. For full duplex mode, IEEE 802.3x flow control function sends PAUSE frames and receives PAUSE frames.rw Enumeration .1.3.6.1.4.1.171.11.101.1.2.3.2.1.6 |
swL2PortCtrlLearningStateThis object decides if the port is locked or not.rw Enumeration .1.3.6.1.4.1.171.11.101.1.2.3.2.1.7 |
swL2PortCtrlMACNotifyStateThis object sets each port's MAC notification state.rw Enumeration .1.3.6.1.4.1.171.11.101.1.2.3.2.1.8 |
swL2PortCtrlJumboFrameThis object configures the switch's jumbo frame settings.rw Enumeration .1.3.6.1.4.1.171.11.101.1.2.3.3 |
swL2PortCtrlJumboFrameMaxSizeThis object describes how many bytes the max jumbo frame is.ro INTEGER .1.3.6.1.4.1.171.11.101.1.2.3.4 |
swL2PortCounterCtrlTableA table that used to clear counter information about every port. SEQUENCE OF SwL2PortCounterCtrlEntry .1.3.6.1.4.1.171.11.101.1.2.3.6 |
swL2PortCounterCtrlEntryA list of entry used to clear counter information for each port of the device. SwL2PortCounterCtrlEntry .1.3.6.1.4.1.171.11.101.1.2.3.6.1 |
swL2PortCounterCtrlPortIndexThis object indicates the module's port number.(1..Max port number in the module)ro INTEGER .1.3.6.1.4.1.171.11.101.1.2.3.6.1.1 |
swL2PortCounterClearCtrlThis object indicates if to clear the counters for each port of the device or not.rw Enumeration .1.3.6.1.4.1.171.11.101.1.2.3.6.1.2 |
swL2PortErrTableA table that contains error information for each port. SEQUENCE OF SwL2PortErrEntry .1.3.6.1.4.1.171.11.101.1.2.3.7 |
swL2PortErrEntryA list of information regarding port errors on the device. SwL2PortErrEntry .1.3.6.1.4.1.171.11.101.1.2.3.7.1 |
swL2PortErrPortIndexThis object indicates the module's port number.(1..Max port number in the module).ro INTEGER .1.3.6.1.4.1.171.11.101.1.2.3.7.1.1 |
swL2PortErrPortStateThis object indicates the port state is enabled or disabled.ro Enumeration .1.3.6.1.4.1.171.11.101.1.2.3.7.1.2 |
swL2PortErrPortConnStatusThis object indicates whether the PortStatus is err-disabled or not.ro Enumeration .1.3.6.1.4.1.171.11.101.1.2.3.7.1.3 |
swL2PortErrPortReasonThis object describes if the reason for the port error is STP LBD or Storm control.ro Enumeration .1.3.6.1.4.1.171.11.101.1.2.3.7.1.4 |
swL2LimitedMulticastMgmt OBJECT IDENTIFIER .1.3.6.1.4.1.171.11.101.1.2.5 |
swL2MulticastFilterProfileTableA table that contains information about multicast filter address. SEQUENCE OF SwL2MulticastFilterProfileEntry .1.3.6.1.4.1.171.11.101.1.2.5.1 |
swL2MulticastFilterProfileEntryA list of multicast filter address information for each profile ID. SwL2MulticastFilterProfileEntry .1.3.6.1.4.1.171.11.101.1.2.5.1.1 |
swL2MulticastFilterProfileIndexIndicates index for each profile.ro INTEGER .1.3.6.1.4.1.171.11.101.1.2.5.1.1.1 |
swL2MulticastFilterProfileNameSpecifies a profile name for each multicast filter profile.rw DisplayString .1.3.6.1.4.1.171.11.101.1.2.5.1.1.2 |
swL2MulticastFilterStatusThis object indicates the status of this entry.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.171.11.101.1.2.5.1.1.3 |
swL2MulticastFilterProfileAddressTableA table that contains information about multicast filter address. SEQUENCE OF SwL2MulticastFilterProfileAddressEntry .1.3.6.1.4.1.171.11.101.1.2.5.2 |
swL2MulticastFilterProfileAddressEntryA list of multicast filter address information for each profile ID. SwL2MulticastFilterProfileAddressEntry .1.3.6.1.4.1.171.11.101.1.2.5.2.1 |
swL2MulticastFilterProfileIdIndexIndicates index for each profile.ro INTEGER .1.3.6.1.4.1.171.11.101.1.2.5.2.1.1 |
swL2MulticastFilterFromIpSpecifies the head IP address of a multicast address range which will be binded to a multicast filter profile.ro IpAddress .1.3.6.1.4.1.171.11.101.1.2.5.2.1.2 |
swL2MulticastFilterToIpSpecifies the tail IP address of a multicast address range which will be binded to a multicast filter profile.ro IpAddress .1.3.6.1.4.1.171.11.101.1.2.5.2.1.3 |
swL2MulticastFilterAddressStateThis object indicates the status of this entry. Setting value to createAndGo(4) will add the multicast address list specified in swL2MulticastFilterFromIp and swL2MulticastFilterToIp to multicast filter profile. Setting value to destroy(6) will remove the multicast address list specified in swL2MulticastFilterFromIp and swL2MulticastFilterToIp from multicast filter profile.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.171.11.101.1.2.5.2.1.4 |
swL2LimitedMulticastFilterPortTableA table that used to bind port to profile id. SEQUENCE OF SwL2LimitedMulticastFilterPortEntry .1.3.6.1.4.1.171.11.101.1.2.5.3 |
swL2LimitedMulticastFilterPortEntryA list of information that used to bind port to profile id. SwL2LimitedMulticastFilterPortEntry .1.3.6.1.4.1.171.11.101.1.2.5.3.1 |
swL2LimitedMulticastFilterPortIndexSpecifies port as an index.ro INTEGER .1.3.6.1.4.1.171.11.101.1.2.5.3.1.1 |
swL2LimitedMulticastFilterPortAccessThis object indicates the access status for each port.rw Enumeration .1.3.6.1.4.1.171.11.101.1.2.5.3.1.2 |
swL2LimitedMulticastFilterPortProfileIDThis object specifies a profile ID list for each port.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.171.11.101.1.2.5.3.1.3 |
swL2LimitedMulticastFilterPortProfileStatusControls the multicast filter profile list which bind to each port. When set add(2), multicast filter profile ID list which specifies in swL2LimitedMulticastFilterPortProfileID will be bound to the port. When set delete(3), multicast filter profile ID list which specifies in swL2LimitedMulticastFilterPortProfileID will be unbound from the port. The attribute value reverts to 'other' once the action has been done.rw Enumeration .1.3.6.1.4.1.171.11.101.1.2.5.3.1.4 |
swL2MulticastFilterPortMaxGroupTableA table that contains information about max group number based on port. SEQUENCE OF SwL2MulticastFilterPortMaxGroupEntry .1.3.6.1.4.1.171.11.101.1.2.5.4 |
swL2MulticastFilterPortMaxGroupEntryA list of max group number information for each port. SwL2MulticastFilterPortMaxGroupEntry .1.3.6.1.4.1.171.11.101.1.2.5.4.1 |
swL2MulticastFilterPortMaxGroupPortIndexSpecifies port number as table index.ro INTEGER .1.3.6.1.4.1.171.11.101.1.2.5.4.1.1 |
swL2MulticastFilterPortMaxGroupSpecifies maximum multicast filter group numbers for each port. Default value is 256.rw INTEGER .1.3.6.1.4.1.171.11.101.1.2.5.4.1.2 |
swL2QOSMgmt OBJECT IDENTIFIER .1.3.6.1.4.1.171.11.101.1.2.6 |
swL2QOSBandwidthControlTable. SEQUENCE OF SwL2QOSBandwidthControlEntry .1.3.6.1.4.1.171.11.101.1.2.6.1 |
swL2QOSBandwidthControlEntryA list of information contained in the swL2QOSBandwidthControlTable. SwL2QOSBandwidthControlEntry .1.3.6.1.4.1.171.11.101.1.2.6.1.1 |
swL2QOSBandwidthPortIndexIndicates the port .ro INTEGER .1.3.6.1.4.1.171.11.101.1.2.6.1.1.1 |
swL2QOSBandwidthRxRateIndicates RX Rate(64Kbit/sec) of the specified port. Value 1024001 means no limit.rw INTEGER .1.3.6.1.4.1.171.11.101.1.2.6.1.1.2 |
swL2QOSBandwidthTxRateIndicates TX Rate(64Kbit/sec) of the specified port. Value 1024001 means no limit.rw INTEGER .1.3.6.1.4.1.171.11.101.1.2.6.1.1.3 |
swL2QOSBandwidthRadiusRxRateThe RxRate value comes from RADIUS server, If an 802.1X port is authenticated, this value will overwrites the locally configured RxRate.ro INTEGER .1.3.6.1.4.1.171.11.101.1.2.6.1.1.4 |
swL2QOSBandwidthRadiusTxRateThe TxRate value comes from RADIUS server, If an 802.1X port is authenticated, this value will overwrites the locally configured TxRate.ro INTEGER .1.3.6.1.4.1.171.11.101.1.2.6.1.1.5 |
swL2QOSSchedulingTable. SEQUENCE OF SwL2QOSSchedulingEntry .1.3.6.1.4.1.171.11.101.1.2.6.2 |
swL2QOSSchedulingEntryA list of information contained in the swL2QOSSchedulingTable. SwL2QOSSchedulingEntry .1.3.6.1.4.1.171.11.101.1.2.6.2.1 |
swL2QOSSchedulingClassIndexIndicates the hardware queue number.ro INTEGER .1.3.6.1.4.1.171.11.101.1.2.6.2.1.1 |
swL2QOSSchedulingMaxPktsIndicates the maximum number of packets the hardware priority queue will be allowed to transmit before allowing the next lowest priority queue to transmit its packets. a value between 0 and 15 can be specified.rw INTEGER .1.3.6.1.4.1.171.11.101.1.2.6.2.1.2 |
swL2QOSSchedulingMechanismIndicates the mechanism of QoS scheduling.ro Enumeration .1.3.6.1.4.1.171.11.101.1.2.6.2.1.3 |
swL2QOS8021pUserPriorityTable. SEQUENCE OF SwL2QOS8021pUserPriorityEntry .1.3.6.1.4.1.171.11.101.1.2.6.3 |
swL2QOS8021pUserPriorityEntryA list of information contained in the swL2QOS8021pUserPriorityTable. SwL2QOS8021pUserPriorityEntry .1.3.6.1.4.1.171.11.101.1.2.6.3.1 |
swL2QOS8021pUserPriorityIndexThe 802.1p user priority .ro INTEGER .1.3.6.1.4.1.171.11.101.1.2.6.3.1.1 |
swL2QOS8021pUserPriorityClassThe number of the switch's hardware priority queue. The switch has seven hardware priority queues available. They are numbered between 0 (the lowest priority) and 6 (the highest priority).rw INTEGER .1.3.6.1.4.1.171.11.101.1.2.6.3.1.2 |
swL2QOS8021pDefaultPriorityTable. SEQUENCE OF SwL2QOS8021pDefaultPriorityEntry .1.3.6.1.4.1.171.11.101.1.2.6.4 |
swL2QOS8021pDefaultPriorityEntryA list of information contained in the swL2QOS8021pDefaultPriorityTable. SwL2QOS8021pDefaultPriorityEntry .1.3.6.1.4.1.171.11.101.1.2.6.4.1 |
swL2QOS8021pDefaultPriorityIndexIndicates the port number .ro INTEGER .1.3.6.1.4.1.171.11.101.1.2.6.4.1.1 |
swL2QOS8021pDefaultPriorityThe priority value to assign to untagged packets received by the switch ports on the switch..rw INTEGER .1.3.6.1.4.1.171.11.101.1.2.6.4.1.2 |
swL2QOS8021pRadiusPriorityThe value of 802.1p comes from RADIUS server. If an 802.1X port is authenticated, this value will overwrite the local configured value.ro INTEGER .1.3.6.1.4.1.171.11.101.1.2.6.4.1.3 |
swL2QOSSchedulingMechanismCtrlThis object controls QoS scheduling Mechanism.rw Enumeration .1.3.6.1.4.1.171.11.101.1.2.6.5 |
swL2PortSecurityMgmt OBJECT IDENTIFIER .1.3.6.1.4.1.171.11.101.1.2.7 |
swL2PortSecurityControlTableA port security feature which controls the address leaning capability and traffic forwarding decisions. Each port can be enabled or disabled for this function. When it is enabled and a number is given said N, which allows N addresses to be learned on this port, the first N learned addresses are locked at this port as static entries. When the learned addresses number reaches N, any incoming packet without learned source addresses are discarded (e.g. dropped) and no more new addresses can be learned on this port. SEQUENCE OF SwL2PortSecurityControlEntry .1.3.6.1.4.1.171.11.101.1.2.7.1 |
swL2PortSecurityControlEntryA list of information contained in the swL2PortSecurityControlTable. SwL2PortSecurityControlEntry .1.3.6.1.4.1.171.11.101.1.2.7.1.1 |
swL2PortSecurityPortIndexIndicates the secured port to lock address learning.ro INTEGER .1.3.6.1.4.1.171.11.101.1.2.7.1.1.1 |
swL2PortSecurityMaxLernAddrIndicates allowable number of addresses to be learned on this port.rw INTEGER .1.3.6.1.4.1.171.11.101.1.2.7.1.1.2 |
swL2PortSecurityModeIndicates the mode of locking address. In deleteOnTimeout(3) mode - the locked addresses can be aged out after the aging timer expires. In this mode, when the locked address is aged out, the number of addresses that can be learned has to be increased by one. In deleteOnReset(4) mode - Locked addresses never age out unless the system restarts which will prevent port movement or intrusion.rw Enumeration .1.3.6.1.4.1.171.11.101.1.2.7.1.1.3 |
swL2PortSecurityAdmStateIndicates administration state of locking address.rw Enumeration .1.3.6.1.4.1.171.11.101.1.2.7.1.1.4 |
swL2PortSecurityEntryClearCtrlUsed to clear port security entries by port. Setting this value to 'start' will execute the clear action, Once cleared, the value returns to 'other'.rw Enumeration .1.3.6.1.4.1.171.11.101.1.2.7.1.1.5 |
swL2PortSecurityDelCtrl OBJECT IDENTIFIER .1.3.6.1.4.1.171.11.101.1.2.7.2 |
swL2PortSecurityDelVlanNameIndicates VLAN name.rw DisplayString .1.3.6.1.4.1.171.11.101.1.2.7.2.1 |
swL2PortSecurityDelPortIndicates the port.rw INTEGER .1.3.6.1.4.1.171.11.101.1.2.7.2.2 |
swL2PortSecurityDelMacAddressSpecifies a MAC address.rw MacAddress (SNMPv2-TC) .1.3.6.1.4.1.171.11.101.1.2.7.2.3 |
swL2PortSecurityDelActivity.rw Enumeration .1.3.6.1.4.1.171.11.101.1.2.7.2.4 |
swL2PortSecurityTrapLogStateWhen enabled(2),whenever there's a new MAC address that violates the pre-defined port security configuration, traps will be sent out and the relevant information will be logged into the system.rw Enumeration .1.3.6.1.4.1.171.11.101.1.2.7.3 |
swL2DhcpRelayMgmt OBJECT IDENTIFIER .1.3.6.1.4.1.171.11.101.1.2.8 |
swL2DhcpRelayStateThis object indicates if the DHCP relay function is enabled or disabled.rw Enumeration .1.3.6.1.4.1.171.11.101.1.2.8.1 |
swL2DhcpRelayHopCountThis object indicates the maximum number of router hops that DHCP packets can cross.rw INTEGER .1.3.6.1.4.1.171.11.101.1.2.8.2 |
swL2DhcpRelayTimeThresholdThis object indicates the minimum time in seconds within which the switch must relay the DHCP request. If this time is exceeded, the switch will drop the DHCP packet.rw INTEGER .1.3.6.1.4.1.171.11.101.1.2.8.3 |
swL2DhcpRelayOption82StateThis object indicates if the DHCP relay agent information option 82 function is enabled or disabled.rw Enumeration .1.3.6.1.4.1.171.11.101.1.2.8.4 |
swL2DhcpRelayOption82CheckThis object indicates if the checking mechanism of DHCP relay agent information option 82 is enabled or disabled.rw Enumeration .1.3.6.1.4.1.171.11.101.1.2.8.5 |
swL2DhcpRelayOption82PolicyThis object indicates the reforwarding policy of DHCP relay agent information option 82. replace(1) - replace the exiting option 82 field in messages. drop(2) - discard messages with existing option 82 field. keep(3) - retain the existing option 82 field messages.rw Enumeration .1.3.6.1.4.1.171.11.101.1.2.8.6 |
swL2DhcpRelayCtrlTableThis table specifies the IP address as a destination to forward (relay) DHCP packets to. SEQUENCE OF SwL2DhcpRelayCtrlEntry .1.3.6.1.4.1.171.11.101.1.2.8.7 |
swL2DhcpRelayCtrlEntryA list of information that specifies the IP address as a destination to forward (relay) DHCP packets to. SwL2DhcpRelayCtrlEntry .1.3.6.1.4.1.171.11.101.1.2.8.7.1 |
swL2DhcpRelayCtrlInterfaceNameThe name of the IP interface.ro DisplayString .1.3.6.1.4.1.171.11.101.1.2.8.7.1.1 |
swL2DhcpRelayCtrlServerThe DHCP server IP address.ro IpAddress .1.3.6.1.4.1.171.11.101.1.2.8.7.1.2 |
swL2DhcpRelayCtrlStateThis object indicates the status of this entry. other(1) - this entry is currently in use but the conditions under which it will remain so are different from each of the following values. invalid(2) - writing this value to the object, and then the corresponding entry will be removed from the table. valid(3) - this entry resides in the table.rw Enumeration .1.3.6.1.4.1.171.11.101.1.2.8.7.1.3 |
swL2TrunkMgmt OBJECT IDENTIFIER .1.3.6.1.4.1.171.11.101.1.2.9 |
swL2TrunkMaxSupportedEntriesMaximum number of entries in the trunk configuration table (swL2TrunkCtrlTable).ro INTEGER .1.3.6.1.4.1.171.11.101.1.2.9.1 |
swL2TrunkCurrentNumEntriesCurrent active number of entries in the trunk configuration table.ro INTEGER .1.3.6.1.4.1.171.11.101.1.2.9.2 |
swL2TrunkCtrlTableThis table specifies which ports group a set of ports(up to 8) into a single logical link. SEQUENCE OF SwL2TrunkCtrlEntry .1.3.6.1.4.1.171.11.101.1.2.9.3 |
swL2TrunkCtrlEntryA list of information that specifies which ports group a set of ports(up to 8) into a single logical link. SwL2TrunkCtrlEntry .1.3.6.1.4.1.171.11.101.1.2.9.3.1 |
swL2TrunkIndexThe index number of the logical port trunk group. The trunk group number depends on the existence of unit and module.ro INTEGER .1.3.6.1.4.1.171.11.101.1.2.9.3.1.1 |
swL2TrunkMasterPortThe object indicates the master port number of the port trunk entry. When using Port Trunk, you cannot configure the other ports of the group except the master port. Their configuration must be same as the master port (e.g. speed, duplex, enabled/disabled, flow control, and so on).rw INTEGER .1.3.6.1.4.1.171.11.101.1.2.9.3.1.3 |
swL2TrunkMemberIndicates the number of ports included in this Trunk group. The trunk port number depends on the existence of the module. The maximum number of ports is 8 for one trunk group.rw PortList .1.3.6.1.4.1.171.11.101.1.2.9.3.1.4 |
swL2TrunkTypeThis object indicates the type of trunk group. static : is static trunk group lacp : is LACP trunk group .rw Enumeration .1.3.6.1.4.1.171.11.101.1.2.9.3.1.6 |
swL2TrunkStateThis object indicates the status of this entry.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.171.11.101.1.2.9.3.1.7 |
swL2TrunkActivePortThe object indicates the active port of a special trunk group.ro PortList .1.3.6.1.4.1.171.11.101.1.2.9.3.1.8 |
swL2TrunkAlgorithmThis object configures to part of the packet examined by the switch when selecting the egress port for transmitting load-sharing data.rw Enumeration .1.3.6.1.4.1.171.11.101.1.2.9.4 |
swL2TrunkLACPPortTableThis table specifies which ports group a set of ports(up to 8) into a single logical link. SEQUENCE OF SwL2TrunkLACPPortEntry .1.3.6.1.4.1.171.11.101.1.2.9.5 |
swL2TrunkLACPPortEntryA list of information specifies which ports group a set of ports(up to 8) into a single logical link. SwL2TrunkLACPPortEntry .1.3.6.1.4.1.171.11.101.1.2.9.5.1 |
swL2TrunkLACPPortIndexThe index of logical port LACP.ro INTEGER .1.3.6.1.4.1.171.11.101.1.2.9.5.1.1 |
swL2TrunkLACPPortStateThe state of logical port LACP.rw Enumeration .1.3.6.1.4.1.171.11.101.1.2.9.5.1.2 |
swL2TrunkVLANTableThis table is used to manage the VLAN trunking feature of the device. SEQUENCE OF SwL2TrunkVLANEntry .1.3.6.1.4.1.171.11.101.1.2.9.6 |
swL2TrunkVLANEntryThis object is used to configure the VLAN trunking settings for each port. SwL2TrunkVLANEntry .1.3.6.1.4.1.171.11.101.1.2.9.6.1 |
swL2TrunkVLANPortThis object indicates the port being configured.ro INTEGER .1.3.6.1.4.1.171.11.101.1.2.9.6.1.1 |
swL2TrunkVLANStateThe state of the logical port LACP.rw Enumeration .1.3.6.1.4.1.171.11.101.1.2.9.6.1.2 |
swL2MirrorMgmt OBJECT IDENTIFIER .1.3.6.1.4.1.171.11.101.1.2.10 |
swL2MirrorLogicTargetPortThis object indicates which switch port will sniff another port. A trunk port member cannot be configured as a target snooping port. The port number is the sequential (logical) number which is also applied to the bridge MIB, etc.rw INTEGER .1.3.6.1.4.1.171.11.101.1.2.10.1 |
swL2MirrorPortSourceIngressThis represents the port where ingress packets will be sniffed.rw PortList .1.3.6.1.4.1.171.11.101.1.2.10.2 |
swL2MirrorPortSourceEgressThis represents the port where egress packets will be sniffed.rw PortList .1.3.6.1.4.1.171.11.101.1.2.10.3 |
swL2MirrorPortStateThis object indicates the port mirroring state. other(1) - this entry is currently in use but the conditions under which it will remain so are different from each of the following values. disabled(2) - After writing this value to the object, the corresponding entry will be removed from the table. enabled(3) - This entry resides in the table.rw Enumeration .1.3.6.1.4.1.171.11.101.1.2.10.4 |
swL2IGMPMgmt OBJECT IDENTIFIER .1.3.6.1.4.1.171.11.101.1.2.11 |
swL2IGMPMaxSupportedVlansMaximum number of VLANs in the layer 2 IGMP control table (swL2IGMPCtrlTable).ro INTEGER .1.3.6.1.4.1.171.11.101.1.2.11.1 |
swL2IGMPMaxIpGroupNumPerVlanMaximum number of multicast IP groups per VLAN in the layer 2 IGMP information table(swL2IGMPQueryInfoTable).ro INTEGER .1.3.6.1.4.1.171.11.101.1.2.11.2 |
swL2IGMPCtrlTableThe table controls the VLAN's IGMP function. Its scale depends on the current VLAN state (swL2VlanInfoStatus). If the VLAN is disabled, there is only one entry in the table, with an index of 1. If the VLAN is in Port-Base or 802.1q mode, the maximum number of entries can be 12, with an index range from 1 to 12. SEQUENCE OF SwL2IGMPCtrlEntry .1.3.6.1.4.1.171.11.101.1.2.11.3 |
swL2IGMPCtrlEntryThe entry in IGMP control table (swL2IGMPCtrlTable). The entry is effective only when IGMP capture switch (swL2DevCtrlIGMPSnooping) is enabled. SwL2IGMPCtrlEntry .1.3.6.1.4.1.171.11.101.1.2.11.3.1 |
swL2IGMPCtrlVidThis object indicates the IGMP control entry's VLAN ID. If the VLAN is disabled, the VID is always 0 and cannot be changed by management users. If the VLAN is in Port-Base mode, the VID is arranged from 1 to 12, in a fixed form. If the VLAN is in 802.1q mode, the VID setting can be changed from 1 to 4094 by the management user, and the VID in each entry must be unique within the IGMP Control Table.ro INTEGER .1.3.6.1.4.1.171.11.101.1.2.11.3.1.1 |
swL2IGMPQueryIntervalThe frequency at which IGMP Host-Query packets are transmitted on this switch.rw INTEGER .1.3.6.1.4.1.171.11.101.1.2.11.3.1.2 |
swL2IGMPMaxResponseTimeThe maximum query response time on this switch.rw INTEGER .1.3.6.1.4.1.171.11.101.1.2.11.3.1.3 |
swL2IGMPRobustnessThe Robustness Variable allows tuning for the expected packet loss on a subnet. If a subnet is expected to be lossy, the Robustness Variable may be increased. IGMP is robust to (Robustness Variable-1) packet losses.rw INTEGER .1.3.6.1.4.1.171.11.101.1.2.11.3.1.4 |
swL2IGMPLastMemberQueryIntervalThe Last Member Query Interval is the Max Response Time inserted into Group-Specific Queries sent in response to Leave Group messages, and is also the amount of time between Group-Specific Query messages.rw INTEGER .1.3.6.1.4.1.171.11.101.1.2.11.3.1.5 |
swL2IGMPHostTimeoutThe timer value for sending IGMP query packets when none were sent by the host on the LAN. The timer works on a per-VLAN basis. Our device will be activated to send the query messages if the timer expires. Please reference RFC2236-1997.rw INTEGER .1.3.6.1.4.1.171.11.101.1.2.11.3.1.6 |
swL2IGMPRouteTimeoutThe Router Timeout is how long a host must wait after hearing a Query before it may send any IGMPv2 messages.rw INTEGER .1.3.6.1.4.1.171.11.101.1.2.11.3.1.7 |
swL2IGMPLeaveTimerWhen a querier receives a Leave Group message for a group that has group members on the reception interface, it sends Group-Specific Queries every swL2IGMPLeaveTimer to the group being left.rw INTEGER .1.3.6.1.4.1.171.11.101.1.2.11.3.1.8 |
swL2IGMPQueryStateThis object decides if the IGMP query is enabled or disabled.rw Enumeration .1.3.6.1.4.1.171.11.101.1.2.11.3.1.9 |
swL2IGMPCurrentStateThis object indicates the current IGMP query state.ro Enumeration .1.3.6.1.4.1.171.11.101.1.2.11.3.1.10 |
swL2IGMPCtrlStateThis object indicates the status of this entry. other(1) - this entry is currently in use but the conditions under which it will remain so are different from each of the following values. disable(2) - IGMP function is disabled for this entry. enable(3) - IGMP function is enabled for this entry.rw Enumeration .1.3.6.1.4.1.171.11.101.1.2.11.3.1.11 |
swL2IGMPFastLeaveStateThis object indicates the fast-leave status of this entry. other(1) - this entry is currently in use but the conditions under which it will remain so are different from each of the following values. disable(2) - IGMP fast-leave function is disabled for this entry. enable(3) - IGMP fast-leave function is enabled for this entry.rw Enumeration .1.3.6.1.4.1.171.11.101.1.2.11.3.1.12 |
swL2IGMPQueryVersionConfigure the IGMP version of query packet which will be sent by router.rw INTEGER .1.3.6.1.4.1.171.11.101.1.2.11.3.1.13 |
swL2IGMPQueryInfoTableThe table contains the number current IGMP query packets which are captured by this device, as well as the IGMP query packets sent by the device. SEQUENCE OF SwL2IGMPQueryInfoEntry .1.3.6.1.4.1.171.11.101.1.2.11.4 |
swL2IGMPQueryInfoEntryInformation about current IGMP query information, provided that swL2DevCtrlIGMPSnooping and swL2IGMPCtrState of the associated VLAN entry are all enabled. SwL2IGMPQueryInfoEntry .1.3.6.1.4.1.171.11.101.1.2.11.4.1 |
swL2IGMPInfoVidThis object indicates the VID of associated IGMP info table entry. It follows swL2IGMPCtrlVid in the associated entry of IGMP control table (swL2IGMPCtrlTable).ro INTEGER .1.3.6.1.4.1.171.11.101.1.2.11.4.1.1 |
swL2IGMPInfoQueryCountThis object indicates the number of query packets received since the IGMP function was enabled, on a per-VLAN basis.ro INTEGER .1.3.6.1.4.1.171.11.101.1.2.11.4.1.2 |
swL2IGMPInfoTxQueryCountThis object indicates the send count of IGMP query messages, in per-VLAN basis. In case of IGMP timer expiration, the switch sends IGMP query packets to related VLAN member ports and increment this object by 1.ro INTEGER .1.3.6.1.4.1.171.11.101.1.2.11.4.1.3 |
swL2IGMPRouterPortTableThe information of the router port table. SEQUENCE OF SwL2IGMPRouterPortEntry .1.3.6.1.4.1.171.11.101.1.2.11.6 |
swL2IGMPRouterPortEntryThe entry of swL2IGMPRouterPortTable. SwL2IGMPRouterPortEntry .1.3.6.1.4.1.171.11.101.1.2.11.6.1 |
swL2IGMPRouterPortVlanidThis object indicates the VLAN ID of the router port entry.ro INTEGER .1.3.6.1.4.1.171.11.101.1.2.11.6.1.1 |
swL2IGMPRouterPortVlanNameThis object indicates the VLAN name of the router port entry.ro DisplayString .1.3.6.1.4.1.171.11.101.1.2.11.6.1.2 |
swL2IGMPRouterPortStaticPortListThis object indicates the static portlist of the router port entry.rw PortList .1.3.6.1.4.1.171.11.101.1.2.11.6.1.3 |
swL2IGMPRouterPortDynamicPortListThis object indicates the dynamic portlist of the router port entry.ro PortList .1.3.6.1.4.1.171.11.101.1.2.11.6.1.4 |
swL2IGMPRouterPortForbiddenPortListThis object indicates the forbidden portlist of the router port entry.rw PortList .1.3.6.1.4.1.171.11.101.1.2.11.6.1.5 |
swIGMPSnoopingGroupTableThe table contains the current IGMP snooping group information captured by the device. SEQUENCE OF SwIGMPSnoopingGroupEntry .1.3.6.1.4.1.171.11.101.1.2.11.11 |
swIGMPSnoopingGroupEntryInformation about the current IGMP snooping group information which has been captured by the device. SwIGMPSnoopingGroupEntry .1.3.6.1.4.1.171.11.101.1.2.11.11.1 |
swIGMPSnoopingGroupVidThis object indicates the VID of the individual IGMP snooping group table entry.ro INTEGER .1.3.6.1.4.1.171.11.101.1.2.11.11.1.1 |
swIGMPSnoopingGroupGroupAddrThis object identifies the group IP address which has been captured from the IGMP packet, on a per-VLAN basis.ro IpAddress .1.3.6.1.4.1.171.11.101.1.2.11.11.1.2 |
swIGMPSnoopingGroupSourceAddrThis object identifies the source addresses.ro IpAddress .1.3.6.1.4.1.171.11.101.1.2.11.11.1.3 |
swIGMPSnoopingGroupIncludePortMapThis object indicates the port list under INCLUDE mode.ro PortList .1.3.6.1.4.1.171.11.101.1.2.11.11.1.4 |
swIGMPSnoopingGroupExcludePortMapThis object indicates the port list under EXCLUDE mode.ro PortList .1.3.6.1.4.1.171.11.101.1.2.11.11.1.5 |
swIGMPSnoopingGroupReportCountThis object indicates how many report packets were received by our device corresponding with this entry that has the IGMP function enabled, on a per-group basis.ro INTEGER .1.3.6.1.4.1.171.11.101.1.2.11.11.1.6 |
swIGMPSnoopingGroupUpTimeThis object indicates how long since the group was detected.ro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.171.11.101.1.2.11.11.1.7 |
swIGMPSnoopingGroupExpiryTimeThis object indicates the time left before this group will be aged out.ro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.171.11.101.1.2.11.11.1.8 |
swIGMPSnoopingGroupRouterPortsThis object indicates the port number of the router ports.ro PortList .1.3.6.1.4.1.171.11.101.1.2.11.11.1.9 |
swL2IGMPDynIpMultMgmt OBJECT IDENTIFIER .1.3.6.1.4.1.171.11.101.1.2.11.12 |
swL2IGMPDynIPMultMaxEntryThis object specifies the maximum number of entries which can be learned by dynamic IP multicastrw INTEGER .1.3.6.1.4.1.171.11.101.1.2.11.12.1 |
swL2IGMPDynIPMultCtrlTableThis table is used to manage the IGMP dynamic IP multicast. SEQUENCE OF SwL2IGMPDynIPMultCtrlEntry .1.3.6.1.4.1.171.11.101.1.2.11.12.3 |
swL2IGMPDynIPMultCtrlEntryA list of manageable entities for IGMP dynamic IP multicast. SwL2IGMPDynIPMultCtrlEntry .1.3.6.1.4.1.171.11.101.1.2.11.12.3.1 |
swL2IGMPDynIPMultVlanStateThis object is used to disable or enable the dynamic IP multicast feature in this VLAN.rw Enumeration .1.3.6.1.4.1.171.11.101.1.2.11.12.3.1.1 |
swL2IGMPDynIPMultVlanAgeThis object is used to enable or disable aging on the dynamic IP multicast entry in this VLAN.rw Enumeration .1.3.6.1.4.1.171.11.101.1.2.11.12.3.1.2 |
swL2IGMPAccessAuthTableThis table is used to manage the IGMP Access Authentication configurations of the device. SEQUENCE OF SwL2IGMPAccessAuthEntry .1.3.6.1.4.1.171.11.101.1.2.11.20 |
swL2IGMPAccessAuthEntryA list of manageable entities for IGMP Access Authentication. The configuration is done per port. SwL2IGMPAccessAuthEntry .1.3.6.1.4.1.171.11.101.1.2.11.20.1 |
swL2IGMPAccessAuthPortThe index of the swL2IGMPAccessAuthTable. This object corresponds to the port being configured.ro INTEGER .1.3.6.1.4.1.171.11.101.1.2.11.20.1.1 |
swL2IGMPAccessAuthStateThis object denotes the status of IGMP Access Authentication of the port.rw Enumeration .1.3.6.1.4.1.171.11.101.1.2.11.20.1.2 |
swL2TrafficSegMgmt OBJECT IDENTIFIER .1.3.6.1.4.1.171.11.101.1.2.14 |
swL2TrafficSegTableThis table specifies that the port can just forward traffic to the specific port list. SEQUENCE OF SwL2TrafficSegEntry .1.3.6.1.4.1.171.11.101.1.2.14.1 |
swL2TrafficSegEntryA list of information which specifies the port with its traffic forwarding list. SwL2TrafficSegEntry .1.3.6.1.4.1.171.11.101.1.2.14.1.1 |
swL2TrafficSegPortThe port number of the logical port.ro INTEGER .1.3.6.1.4.1.171.11.101.1.2.14.1.1.1 |
swL2TrafficSegForwardPortsThe port list to which the specific port can forward traffic.rw PortList .1.3.6.1.4.1.171.11.101.1.2.14.1.1.2 |
swL2MulticastFilterMode OBJECT IDENTIFIER .1.3.6.1.4.1.171.11.101.1.2.17 |
swL2MulticastFilterModeVlanTableA table that contains information about VLAN multicast filter mode. SEQUENCE OF SwL2MulticastFilterModeVlanEntry .1.3.6.1.4.1.171.11.101.1.2.17.1 |
swL2MulticastFilterModeVlanEntryA list of multicast filter mode information for each VLAN. SwL2MulticastFilterModeVlanEntry .1.3.6.1.4.1.171.11.101.1.2.17.1.1 |
swL2MulticastFilterVidIndicates VID for each VLAN.ro INTEGER .1.3.6.1.4.1.171.11.101.1.2.17.1.1.1 |
swL2MulticastFilterVlanModeSpecifies multicast filter mode for each VLAN.rw Enumeration .1.3.6.1.4.1.171.11.101.1.2.17.1.1.2 |
swL2LoopDetectMgmt OBJECT IDENTIFIER .1.3.6.1.4.1.171.11.101.1.2.18 |
swL2LoopDetectCtrl OBJECT IDENTIFIER .1.3.6.1.4.1.171.11.101.1.2.18.1 |
swL2LoopDetectAdminStateThis object indicates the loopback detection status for the system.rw Enumeration .1.3.6.1.4.1.171.11.101.1.2.18.1.1 |
swL2LoopDetectIntervalThis object indicates the interval value, the range is from 1 to 32767 seconds.rw INTEGER .1.3.6.1.4.1.171.11.101.1.2.18.1.2 |
swL2LoopDetectRecoverTimeThis object indicates the recover time, the range is from 60 to 1000000. The value of 0 disables the recover function.rw INTEGER .1.3.6.1.4.1.171.11.101.1.2.18.1.3 |
swL2LoopDetectModeThis object indicates the loopback detection mode for the system.rw Enumeration .1.3.6.1.4.1.171.11.101.1.2.18.1.4 |
swL2LoopDetectTrapModeThis object indicates the loopback detection trap mode for the system.rw Enumeration .1.3.6.1.4.1.171.11.101.1.2.18.1.5 |
swL2LoopDetectPortMgmt OBJECT IDENTIFIER .1.3.6.1.4.1.171.11.101.1.2.18.2 |
swL2LoopDetectPortTableThe table specifies the loopback detection function specified by port. SEQUENCE OF SwL2LoopDetectPortEntry .1.3.6.1.4.1.171.11.101.1.2.18.2.1 |
swL2LoopDetectPortEntryThe table specifies the loopback detection function specified by port. SwL2LoopDetectPortEntry .1.3.6.1.4.1.171.11.101.1.2.18.2.1.1 |
swL2LoopDetectPortIndexThis object indicates the module's port number. The range is from 1 to the maximum port number specified in the modulero INTEGER .1.3.6.1.4.1.171.11.101.1.2.18.2.1.1.1 |
swL2LoopDetectPortStateThis object indicates the loopback detection function state on the port.rw Enumeration .1.3.6.1.4.1.171.11.101.1.2.18.2.1.1.2 |
swL2LoopDetectPortLoopVLANThis object indicates the VLAN list that has detected a loopback.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.171.11.101.1.2.18.2.1.1.3 |
swL2LoopDetectPortLoopStatusThis object indicates the port status.ro Enumeration .1.3.6.1.4.1.171.11.101.1.2.18.2.1.1.4 |
swL2DhcpLocalRelayMgmt OBJECT IDENTIFIER .1.3.6.1.4.1.171.11.101.1.2.24 |
swL2DhcpLocalRelayStateThis object indicates the status of the DHCP local relay function of the switch.rw Enumeration .1.3.6.1.4.1.171.11.101.1.2.24.1 |
swL2DhcpLocalRelayVLANTableThis table is used to manage the DHCP local relay status for each VLAN. SEQUENCE OF SwL2DhcpLocalRelayVLANEntry .1.3.6.1.4.1.171.11.101.1.2.24.2 |
swL2DhcpLocalRelayVLANEntryThis object lists the current VLANs in the switch and their corresponding DHCP local relay status. SwL2DhcpLocalRelayVLANEntry .1.3.6.1.4.1.171.11.101.1.2.24.2.1 |
swL2DhcpLocalRelayVLANIDThis object shows the VIDs of the current VLANS in the switch.ro INTEGER .1.3.6.1.4.1.171.11.101.1.2.24.2.1.1 |
swL2DhcpLocalRelayVLANStateThis object indicates the status of the DHCP relay function of the VLAN.rw Enumeration .1.3.6.1.4.1.171.11.101.1.2.24.2.1.2 |
swL2MgmtMIBTraps OBJECT IDENTIFIER .1.3.6.1.4.1.171.11.101.1.2.100 |
swL2Notify OBJECT IDENTIFIER .1.3.6.1.4.1.171.11.101.1.2.100.1 |
swL2NotifyMgmt OBJECT IDENTIFIER .1.3.6.1.4.1.171.11.101.1.2.100.1.1 |
swL2NotifyPrefix OBJECT IDENTIFIER .1.3.6.1.4.1.171.11.101.1.2.100.1.2 |
swL2NotifFirmware OBJECT IDENTIFIER .1.3.6.1.4.1.171.11.101.1.2.100.1.2.0 |
swL2macNotificationThis trap indicates the MAC addresses variation in address table . NOTIFICATION-TYPE .1.3.6.1.4.1.171.11.101.1.2.100.1.2.0.1 |
swL2PortSecurityViolationTrapWhen the port-security trap is enabled, new MAC addresses that violate the pre-defined port security configuration will trigger trap messages to be sent out. NOTIFICATION-TYPE .1.3.6.1.4.1.171.11.101.1.2.100.1.2.0.2 |
swL2PortLoopOccurredThe trap is sent when a Port loop occurs. NOTIFICATION-TYPE .1.3.6.1.4.1.171.11.101.1.2.100.1.2.0.3 |
swL2PortLoopRestartThe trap is sent when a Port loop restarts after the interval time. NOTIFICATION-TYPE .1.3.6.1.4.1.171.11.101.1.2.100.1.2.0.4 |
swL2VlanLoopOccurredThe trap is sent when a Port with a VID loop occurs. NOTIFICATION-TYPE .1.3.6.1.4.1.171.11.101.1.2.100.1.2.0.5 |
swL2VlanLoopRestartThe trap is sent when a Port with a VID loop restarts after the interval time. NOTIFICATION-TYPE .1.3.6.1.4.1.171.11.101.1.2.100.1.2.0.6 |
swl2NotificationBidings OBJECT IDENTIFIER .1.3.6.1.4.1.171.11.101.1.2.100.1.2.1 |
swL2macNotifyInfoThis object indicates the last time reboot information.ro OCTET STRING .1.3.6.1.4.1.171.11.101.1.2.100.1.2.1.1 |
swL2PortSecurityViolationMacThis object indicates the MAC address that violates the port security configuration.ro MacAddress (SNMPv2-TC) .1.3.6.1.4.1.171.11.101.1.2.100.1.2.1.2 |
swL2VlanLoopDetectVIDThis object indicates the VID that detected a loopback.ro INTEGER .1.3.6.1.4.1.171.11.101.1.2.100.1.2.1.3 |