DGS-3420-28PC-L2MGMT-MIB
The Structure of Layer 2 Network Management Information.
Main OID:
swL2MgmtMIB.dlink-Dgs3420Proj-Dgs3420-28PC.2
138
Objects
Active
Status
7
Dependencies
Imported Objects
Objects
138 total| Object Name |
|---|
swL2MgmtMIBThe Structure of Layer 2 Network Management Information. MODULE-IDENTITY .dlink-Dgs3420Proj-Dgs3420-28PC.2 |
swL2DevMgmt OBJECT IDENTIFIER .dlink-Dgs3420Proj-Dgs3420-28PC.2.1 |
swL2DevInfo OBJECT IDENTIFIER .dlink-Dgs3420Proj-Dgs3420-28PC.2.1.1 |
swDevInfoTotalNumOfPortThe number of ports within this switch. This value is the sum
of the ports within this switch.ro INTEGER .dlink-Dgs3420Proj-Dgs3420-28PC.2.1.1.1 |
swDevInfoNumOfPortInUseThe number of ports in this switch connected to the segment or
the end stations.ro INTEGER .dlink-Dgs3420Proj-Dgs3420-28PC.2.1.1.2 |
swL2DevCtrl OBJECT IDENTIFIER .dlink-Dgs3420Proj-Dgs3420-28PC.2.1.2 |
swL2DevCtrlSnmpTrapStateThis object controls the SNMP trap status.rw Enumeration .dlink-Dgs3420Proj-Dgs3420-28PC.2.1.2.5 |
swL2DevCtrlCleanAllStatisticCounterWhen the object is set to active, all statistical counters will
be cleared. If set to normal, no action will occur.rw Enumeration .dlink-Dgs3420Proj-Dgs3420-28PC.2.1.2.6 |
swL2DevCtrlVlanIdOfFDBTblIndicates the VLAN ID to which the Dot1dTpFdbTable belongs;
The default value is the DEFAULT_VLAN_ID of the system.rw VlanId .dlink-Dgs3420Proj-Dgs3420-28PC.2.1.2.7 |
swL2MACNotifyStateThis object can enable or disable MAC Notification.rw Enumeration .dlink-Dgs3420Proj-Dgs3420-28PC.2.1.2.8 |
swL2MACNotifyHistorySizeThis object indicates the history size of MAC addresses in the MAC Address table.
The default value is 1.rw INTEGER .dlink-Dgs3420Proj-Dgs3420-28PC.2.1.2.9 |
swL2MACNotifyIntervalThis object indicates the time interval, in seconds, that will trigger
MAC notification messages.rw INTEGER .dlink-Dgs3420Proj-Dgs3420-28PC.2.1.2.10 |
swL2DevCtrlAsymVlanStateThis object enables or disables asymmetric VLANs
during the runtime of the system.rw Enumeration .dlink-Dgs3420Proj-Dgs3420-28PC.2.1.2.13 |
swL2DevCtrlTelnet OBJECT IDENTIFIER .dlink-Dgs3420Proj-Dgs3420-28PC.2.1.2.14 |
swL2DevCtrlTelnetStateThis object controls the Telnet status.rw Enumeration .dlink-Dgs3420Proj-Dgs3420-28PC.2.1.2.14.1 |
swL2DevCtrlTelnetTcpPortThis object designates TCP ports.
When Telnet is disabled, this object is not accessible.rw INTEGER .dlink-Dgs3420Proj-Dgs3420-28PC.2.1.2.14.2 |
swL2DevCtrlManagementVlanIdThis object controls which previously created VLANs are included
in the System IP Interface.rw VlanId .dlink-Dgs3420Proj-Dgs3420-28PC.2.1.2.16 |
swL2DevCtrlWeb OBJECT IDENTIFIER .dlink-Dgs3420Proj-Dgs3420-28PC.2.1.2.17 |
swL2DevCtrlWebStateThis object controls the Web status.rw Enumeration .dlink-Dgs3420Proj-Dgs3420-28PC.2.1.2.17.1 |
swL2DevCtrlWebTcpPortThis object designates TCP ports.
When Web is disabled, this object is not accessible.rw INTEGER .dlink-Dgs3420Proj-Dgs3420-28PC.2.1.2.17.2 |
swL2DevCtrlLLDPStateSpecifies the state of the LLDP function.
When this function is enabled, the switch can start to transmit
LLDP packets and receive and process the LLDP packets.
The specific function of each port will depend on the per port
LLDP setting.
For the advertisement of LLDP packets, the switch announces the
information to its neighbor through ports. For receiving
LLDP packets, the switch will learn the information from the LLDP
packets advertised from the neighbor in the neighbor table.rw Enumeration .dlink-Dgs3420Proj-Dgs3420-28PC.2.1.2.18 |
swL2DevCtrlLLDPForwardMessageStateWhen lldp is disabled and lldp forward_message's are enabled, the
LLDP Data Unit packets received by the switch will be forwarded.rw Enumeration .dlink-Dgs3420Proj-Dgs3420-28PC.2.1.2.19 |
swL2DevCtrlIpAutoconfigThis object controls the IP auto configuration state.rw Enumeration .dlink-Dgs3420Proj-Dgs3420-28PC.2.1.2.20 |
swL2DevCtrlCFM OBJECT IDENTIFIER .dlink-Dgs3420Proj-Dgs3420-28PC.2.1.2.21 |
swL2DevCtrlCFMStateThis object indicates the CFM global state.rw Enumeration .dlink-Dgs3420Proj-Dgs3420-28PC.2.1.2.21.1 |
swL2DevCtrlCFMPortTableA table containing the CFM state of specified ports. SEQUENCE OF SwL2DevCtrlCFMPortEntry .dlink-Dgs3420Proj-Dgs3420-28PC.2.1.2.21.2 |
swL2DevCtrlCFMPortEntryThe entry of the CFM state on specified ports. SwL2DevCtrlCFMPortEntry .dlink-Dgs3420Proj-Dgs3420-28PC.2.1.2.21.2.1 |
swL2DevCtrlCFMPortIndexThis object indicates the port number. INTEGER .dlink-Dgs3420Proj-Dgs3420-28PC.2.1.2.21.2.1.1 |
swL2DevCtrlCFMPortStateThis object indicates the CFM state by port.rw Enumeration .dlink-Dgs3420Proj-Dgs3420-28PC.2.1.2.21.2.1.2 |
swL2DevCtrlCFMMaTableA table containing the CFM mode of specified MAs. SEQUENCE OF SwL2DevCtrlCFMMaEntry .dlink-Dgs3420Proj-Dgs3420-28PC.2.1.2.21.3 |
swL2DevCtrlCFMMaEntryThe entry of the CFM mode on specified MAs. SwL2DevCtrlCFMMaEntry .dlink-Dgs3420Proj-Dgs3420-28PC.2.1.2.21.3.1 |
swL2DevCtrlCFMMaModeThis object indicates the CFM mode by MA.rw Enumeration .dlink-Dgs3420Proj-Dgs3420-28PC.2.1.2.21.3.1.1 |
swL2DevCtrlCFMMepTableA table containing the CFM mode of specified MEPs. SEQUENCE OF SwL2DevCtrlCFMMepEntry .dlink-Dgs3420Proj-Dgs3420-28PC.2.1.2.21.4 |
swL2DevCtrlCFMMepEntryThe entry of the CFM mode on specified MEPs. SwL2DevCtrlCFMMepEntry .dlink-Dgs3420Proj-Dgs3420-28PC.2.1.2.21.4.1 |
swL2DevCtrlCFMMepModeThis object indicates the CFM mode by MEP.ro Enumeration .dlink-Dgs3420Proj-Dgs3420-28PC.2.1.2.21.4.1.1 |
swL2DevCtrlVLANTrunkStateThis indicates the global state of the VLAN trunking feature of the device.rw Enumeration .dlink-Dgs3420Proj-Dgs3420-28PC.2.1.2.22 |
swL2DevAlarm OBJECT IDENTIFIER .dlink-Dgs3420Proj-Dgs3420-28PC.2.1.3 |
swL2DevAlarmNewRootWhen the device has become the new root of the Spanning Tree,
this object decides whether to send a new root trap.rw Enumeration .dlink-Dgs3420Proj-Dgs3420-28PC.2.1.3.1 |
swL2DevAlarmTopologyChangeThis object determines whether or not to send a trap message when
the switch topology changes. If the object is enabled (3), the Topology Change
trap is sent by the device when any of its configured ports transition from
the Learning state to the Forwarding state, or from the Forwarding state to
the Blocking state. For the same port transition, the device does not send the
trap if this object value is disabled or in another state.rw Enumeration .dlink-Dgs3420Proj-Dgs3420-28PC.2.1.3.2 |
swL2DevAlarmLinkChangeThis object determines whether or not to send a trap message when the link
changes. If the object is enabled (3), the Link Change trap is sent by
the device when any of its port links change. The device does not send the
trap if this object value is disabled or in another state.rw Enumeration .dlink-Dgs3420Proj-Dgs3420-28PC.2.1.3.3 |
swL2VLANMgmt OBJECT IDENTIFIER .dlink-Dgs3420Proj-Dgs3420-28PC.2.2 |
swL2VlanStaticTableA table containing static configuration information for
each VLAN configured into the device by (local or
network) management. All entries are permanent and will
be restored after the device is reset. SEQUENCE OF SwL2VlanStaticEntry .dlink-Dgs3420Proj-Dgs3420-28PC.2.2.1 |
swL2VlanStaticEntryStatic information for a VLAN configured into this
device by (local or network) management. SwL2VlanStaticEntry .dlink-Dgs3420Proj-Dgs3420-28PC.2.2.1.1 |
swL2VlanIndexThe VLAN-ID or other identifier referring to this VLAN. VlanId .dlink-Dgs3420Proj-Dgs3420-28PC.2.2.1.1.1 |
swL2VLANAdvertisementThis object indicates if the advertisement is active or not.rw Enumeration .dlink-Dgs3420Proj-Dgs3420-28PC.2.2.1.1.2 |
swL2PVIDAutoAssignmentStateThis object controls the PVID auto assignment state.
If 'Auto-assign PVID' is disabled, the PVID can only be changed
by PVID configuration (user changes explicitly). The VLAN
configuration will not automatically change the PVID.
If 'Auto-assign PVID' is enabled, the PVID will be changed by PVID or VLAN configuration. When a user configures
a port to VLAN X's untagged membership, this port's PVID
will be updated with VLAN X. Using the VLAN list command,
PVID is updated as the last item of the VLAN list. When a user removes
a port from the untagged membership of the PVID's VLAN, the
port's PVID will be assigned 'default VLAN'.rw Enumeration .dlink-Dgs3420Proj-Dgs3420-28PC.2.2.2 |
swL2VlanPortInfoTableA table containing the VLAN and port role information of each port. SEQUENCE OF SwL2VlanPortInfoEntry .dlink-Dgs3420Proj-Dgs3420-28PC.2.2.3 |
swL2VlanPortInfoEntryThe table entry of VLAN port information. SwL2VlanPortInfoEntry .dlink-Dgs3420Proj-Dgs3420-28PC.2.2.3.1 |
swL2VlanPortInfoPortIndexThe port index.ro INTEGER .dlink-Dgs3420Proj-Dgs3420-28PC.2.2.3.1.1 |
swL2VlanPortInfoVidThe VLAN ID assigned to a special portro VlanId .dlink-Dgs3420Proj-Dgs3420-28PC.2.2.3.1.2 |
swL2VlanPortInfoPortRoleThe port role of a special port. When the role is 'other', it means this port does not belong to the VLAN.ro Enumeration .dlink-Dgs3420Proj-Dgs3420-28PC.2.2.3.1.3 |
swL2NniGvrpBpduAddressSpecifies the GVRP's BPDU MAC address of the NNI port with Q-in-Q status.rw Enumeration .dlink-Dgs3420Proj-Dgs3420-28PC.2.2.6 |
swL2PortMgmt OBJECT IDENTIFIER .dlink-Dgs3420Proj-Dgs3420-28PC.2.3 |
swL2PortInfoTableA table that contains information about every port. SEQUENCE OF SwL2PortInfoEntry .dlink-Dgs3420Proj-Dgs3420-28PC.2.3.1 |
swL2PortInfoEntryA list of information for each port of the device. SwL2PortInfoEntry .dlink-Dgs3420Proj-Dgs3420-28PC.2.3.1.1 |
swL2PortInfoPortIndexThis object indicates the module's port number.(1..Max port
number in the module)ro INTEGER .dlink-Dgs3420Proj-Dgs3420-28PC.2.3.1.1.1 |
swL2PortInfoMediumTypeIndicates the medium type of the port number.ro Enumeration .dlink-Dgs3420Proj-Dgs3420-28PC.2.3.1.1.2 |
swL2PortInfoUnitIDIndicates the ID of the unit in the system.ro INTEGER .dlink-Dgs3420Proj-Dgs3420-28PC.2.3.1.1.3 |
swL2PortInfoTypeThis object indicates the connector type of this port.ro Enumeration .dlink-Dgs3420Proj-Dgs3420-28PC.2.3.1.1.4 |
swL2PortInfoLinkStatusThis object indicates the port link status.ro Enumeration .dlink-Dgs3420Proj-Dgs3420-28PC.2.3.1.1.5 |
swL2PortInfoNwayStatusThis object indicates the port speed and duplex mode.ro Enumeration .dlink-Dgs3420Proj-Dgs3420-28PC.2.3.1.1.6 |
swL2PortInfoErrorDisabledThis object indicates the blocking type of this port.ro Enumeration .dlink-Dgs3420Proj-Dgs3420-28PC.2.3.1.1.8 |
swL2PortCtrlTableA table that contains control information about every port. SEQUENCE OF SwL2PortCtrlEntry .dlink-Dgs3420Proj-Dgs3420-28PC.2.3.2 |
swL2PortCtrlEntryA list of control information for each port on the device. SwL2PortCtrlEntry .dlink-Dgs3420Proj-Dgs3420-28PC.2.3.2.1 |
swL2PortCtrlPortIndexThis object indicates the module's port number.(1..Max port
number in the module)ro INTEGER .dlink-Dgs3420Proj-Dgs3420-28PC.2.3.2.1.1 |
swL2PortCtrlMediumTypeIndicates the medium type of the port number.ro Enumeration .dlink-Dgs3420Proj-Dgs3420-28PC.2.3.2.1.2 |
swL2PortCtrlUnitIndexIndicates the ID of the unit in the devicero INTEGER .dlink-Dgs3420Proj-Dgs3420-28PC.2.3.2.1.3 |
swL2PortCtrlAdminStateThis object decides if the port is enabled or disabled.rw Enumeration .dlink-Dgs3420Proj-Dgs3420-28PC.2.3.2.1.4 |
swL2PortCtrlNwayStateChose the port speed, duplex mode, and N-Way function mode.rw Enumeration .dlink-Dgs3420Proj-Dgs3420-28PC.2.3.2.1.5 |
swL2PortCtrlFlowCtrlStateThe flow control mechanism is different between full duplex
mode and half duplex mode. For half duplex mode, the jamming
signal is asserted. For full duplex mode, the IEEE 802.3x flow
control function sends PAUSE frames and receives PAUSE frames.rw Enumeration .dlink-Dgs3420Proj-Dgs3420-28PC.2.3.2.1.6 |
swL2PortCtrlLearningStateThis object decides if the port is locked or not.rw Enumeration .dlink-Dgs3420Proj-Dgs3420-28PC.2.3.2.1.7 |
swL2PortCtrlMACNotifyStateThis object sets each port's MAC notification state.rw Enumeration .dlink-Dgs3420Proj-Dgs3420-28PC.2.3.2.1.8 |
swL2PortCtrlMDIXStateThis object configures the MDIX setting of the port.rw Enumeration .dlink-Dgs3420Proj-Dgs3420-28PC.2.3.2.1.10 |
swL2PortCtrlJumboFrameThis object configures the switch's jumbo frame settings.rw Enumeration .dlink-Dgs3420Proj-Dgs3420-28PC.2.3.3 |
swL2PortCtrlJumboFrameMaxSizeThis object describes how many bytes the max jumbo frame is.ro INTEGER .dlink-Dgs3420Proj-Dgs3420-28PC.2.3.4 |
swL2PortCounterCtrlTableA table that is used to clear counter information about every port. SEQUENCE OF SwL2PortCounterCtrlEntry .dlink-Dgs3420Proj-Dgs3420-28PC.2.3.6 |
swL2PortCounterCtrlEntryA list of entries used to clear the counter information for each port of the device. SwL2PortCounterCtrlEntry .dlink-Dgs3420Proj-Dgs3420-28PC.2.3.6.1 |
swL2PortCounterCtrlPortIndexThis object indicates the module's port number.(1..Max port
number in the module)ro INTEGER .dlink-Dgs3420Proj-Dgs3420-28PC.2.3.6.1.1 |
swL2PortCounterClearCtrlThis object indicates whether to clear the counters for each port of the device or not.rw Enumeration .dlink-Dgs3420Proj-Dgs3420-28PC.2.3.6.1.2 |
swL2PortJumboFrameCtrlTableA table that contains information for each port's jumbo frame information. SEQUENCE OF SwL2PortJumboFrameCtrlEntry .dlink-Dgs3420Proj-Dgs3420-28PC.2.3.10 |
swL2PortJumboFrameCtrlEntryA list of information for each port's jumbo frame of the device. SwL2PortJumboFrameCtrlEntry .dlink-Dgs3420Proj-Dgs3420-28PC.2.3.10.1 |
swL2PortJumboFrameCtrlPortIndexThis object indicates the module's port number.(1..Max port number in the module)ro INTEGER .dlink-Dgs3420Proj-Dgs3420-28PC.2.3.10.1.1 |
swL2PortJumboFrameCtrlPortStateThis object indicates if the port's jumbo frame is enabled or disabled.rw Enumeration .dlink-Dgs3420Proj-Dgs3420-28PC.2.3.10.1.2 |
swL2TrunkMgmt OBJECT IDENTIFIER .dlink-Dgs3420Proj-Dgs3420-28PC.2.9 |
swL2TrunkMaxSupportedEntriesMaximum number of entries in the trunk configuration table
(swL2TrunkCtrlTable).ro INTEGER .dlink-Dgs3420Proj-Dgs3420-28PC.2.9.1 |
swL2TrunkCurrentNumEntriesCurrent active number of entries in the trunk configuration
table.ro INTEGER .dlink-Dgs3420Proj-Dgs3420-28PC.2.9.2 |
swL2TrunkCtrlTableThis table specifies information about the logical port trunk groups. SEQUENCE OF SwL2TrunkCtrlEntry .dlink-Dgs3420Proj-Dgs3420-28PC.2.9.3 |
swL2TrunkCtrlEntryA list of information about each logical port trunk group. SwL2TrunkCtrlEntry .dlink-Dgs3420Proj-Dgs3420-28PC.2.9.3.1 |
swL2TrunkIndexThe index number of the logical port trunk group. The trunk group
number depends on the existence of unit and module.ro INTEGER .dlink-Dgs3420Proj-Dgs3420-28PC.2.9.3.1.1 |
swL2TrunkMasterPortThis object indicates the master port number of the port trunk
entry. When using Port Trunking, you cannot configure the other
ports of the group except the master port.
Their configuration must be the same as the master port (e.g. speed,
duplex, enabled/disabled, flow control, and so on).rw INTEGER .dlink-Dgs3420Proj-Dgs3420-28PC.2.9.3.1.3 |
swL2TrunkMemberIndicates the number of ports included in this Trunk group.
The trunk port number depends on the existence of the module.
The maximum number of ports is 8 for one trunk group.rw PortList .dlink-Dgs3420Proj-Dgs3420-28PC.2.9.3.1.4 |
swL2TrunkFloodingPortThe object indicates the flooding port number of the port trunk
entry. The first port of the Trunk group is implicitly configured to
be the flooding port.ro INTEGER .dlink-Dgs3420Proj-Dgs3420-28PC.2.9.3.1.5 |
swL2TrunkTypeThis object indicates the type of trunk group.
static: is a static trunk group
lacp: is a LACP trunk group.rw Enumeration .dlink-Dgs3420Proj-Dgs3420-28PC.2.9.3.1.6 |
swL2TrunkStateThis object indicates the status of this entry.rw RowStatus (SNMPv2-TC) .dlink-Dgs3420Proj-Dgs3420-28PC.2.9.3.1.7 |
swL2TrunkAlgorithmThis object configures part of the packet examined by the
switch when selecting the egress port for transmitting
load-sharing data.rw Enumeration .dlink-Dgs3420Proj-Dgs3420-28PC.2.9.4 |
swL2TrunkLACPPortTableThis table specifies which ports are grouped together (this can be up to 8 ports)
into a single logical link. SEQUENCE OF SwL2TrunkLACPPortEntry .dlink-Dgs3420Proj-Dgs3420-28PC.2.9.5 |
swL2TrunkLACPPortEntryA list of information specifying which ports are grouped together (this can be up to 8 ports)
into a single logical link. SwL2TrunkLACPPortEntry .dlink-Dgs3420Proj-Dgs3420-28PC.2.9.5.1 |
swL2TrunkLACPPortIndexThe index of logical port LACP.ro INTEGER .dlink-Dgs3420Proj-Dgs3420-28PC.2.9.5.1.1 |
swL2TrunkLACPPortStateThe state of a logical port LACP.rw Enumeration .dlink-Dgs3420Proj-Dgs3420-28PC.2.9.5.1.2 |
swL2TrunkVLANTableThis table is used to manage the VLAN trunking feature of the device. SEQUENCE OF SwL2TrunkVLANEntry .dlink-Dgs3420Proj-Dgs3420-28PC.2.9.6 |
swL2TrunkVLANEntryThis object is used to configure the VLAN trunking settings for each port. SwL2TrunkVLANEntry .dlink-Dgs3420Proj-Dgs3420-28PC.2.9.6.1 |
swL2TrunkVLANPortThis object indicates the port being configured.ro INTEGER .dlink-Dgs3420Proj-Dgs3420-28PC.2.9.6.1.1 |
swL2TrunkVLANStateThe state of the logical port VLAN trunk.rw Enumeration .dlink-Dgs3420Proj-Dgs3420-28PC.2.9.6.1.2 |
swL2MirrorMgmt OBJECT IDENTIFIER .dlink-Dgs3420Proj-Dgs3420-28PC.2.10 |
swL2MirrorLogicTargetPortThis object indicates which switch port will sniff another
port. A trunk port member cannot be configured as a target
snooping port. The port number is the sequential (logical)
number, which is also applied to the bridge MIB, etc.rw INTEGER .dlink-Dgs3420Proj-Dgs3420-28PC.2.10.1 |
swL2MirrorPortSourceIngressThis represents the port where ingress packets will be sniffed.rw PortList .dlink-Dgs3420Proj-Dgs3420-28PC.2.10.2 |
swL2MirrorPortSourceEgressThis represents the port where egress packets will be sniffed.rw PortList .dlink-Dgs3420Proj-Dgs3420-28PC.2.10.3 |
swL2MirrorPortStateThis object indicates the port mirroring state.
other (1) - this entry is currently in use but the conditions
under which it will remain so are different from each of the
following values.
disabled (2) - After writing this value to the object, the
corresponding entry will be removed from the table.
enabled (3) - This entry resides in the table.rw Enumeration .dlink-Dgs3420Proj-Dgs3420-28PC.2.10.4 |
swL2MirrorGroupTableThis table specifies information about the Mirror group configuration. SEQUENCE OF SwL2MirrorGroupEntry .dlink-Dgs3420Proj-Dgs3420-28PC.2.10.5 |
swL2MirrorGroupEntryA list of information about each Mirror group configuration. SwL2MirrorGroupEntry .dlink-Dgs3420Proj-Dgs3420-28PC.2.10.5.1 |
swL2MirrorGroupIDThis object indicates the mirror group.
The range of this object is (1..n),
the value of n depends on detail project. INTEGER .dlink-Dgs3420Proj-Dgs3420-28PC.2.10.5.1.1 |
swL2MirrorGroupRowStatusThis object manages this mirror group entry.rw RowStatus (SNMPv2-TC) .dlink-Dgs3420Proj-Dgs3420-28PC.2.10.5.1.2 |
swL2MirrorGroupStateThis object indicates the mirror group state.rw Enumeration .dlink-Dgs3420Proj-Dgs3420-28PC.2.10.5.1.3 |
swL2MirrorGroupLogicTargetPortThis object indicates the mirror group target port.rw INTEGER .dlink-Dgs3420Proj-Dgs3420-28PC.2.10.5.1.4 |
swL2MirrorGroupPortSourceIngressThis object indicates the mirror group ingress source ports.rw PortList .dlink-Dgs3420Proj-Dgs3420-28PC.2.10.5.1.5 |
swL2MirrorGroupPortSourceEngressThis object indicates the mirror group engress source ports.rw PortList .dlink-Dgs3420Proj-Dgs3420-28PC.2.10.5.1.6 |
swL2TrafficSegMgmt OBJECT IDENTIFIER .dlink-Dgs3420Proj-Dgs3420-28PC.2.14 |
swL2TrafficSegTableThis table specifies that the port can just forward traffic to the
specific port list. SEQUENCE OF SwL2TrafficSegEntry .dlink-Dgs3420Proj-Dgs3420-28PC.2.14.1 |
swL2TrafficSegEntryA list of information which specifies the port with its traffic
forwarding list. SwL2TrafficSegEntry .dlink-Dgs3420Proj-Dgs3420-28PC.2.14.1.1 |
swL2TrafficSegPortThe port number of the logical port.ro INTEGER .dlink-Dgs3420Proj-Dgs3420-28PC.2.14.1.1.1 |
swL2TrafficSegForwardPortsThe port list where a specific port can forward traffic.rw PortList .dlink-Dgs3420Proj-Dgs3420-28PC.2.14.1.1.2 |
swL2MulticastFilterMode OBJECT IDENTIFIER .dlink-Dgs3420Proj-Dgs3420-28PC.2.17 |
swL2MulticastFilterModeVlanTableA table that contains information about the VLAN multicast filter mode. SEQUENCE OF SwL2MulticastFilterModeVlanEntry .dlink-Dgs3420Proj-Dgs3420-28PC.2.17.1 |
swL2MulticastFilterModeVlanEntryA list of multicast filter mode information for each VLAN. SwL2MulticastFilterModeVlanEntry .dlink-Dgs3420Proj-Dgs3420-28PC.2.17.1.1 |
swL2MulticastFilterVidIndicates the VID for each VLAN.ro INTEGER .dlink-Dgs3420Proj-Dgs3420-28PC.2.17.1.1.1 |
swL2MulticastFilterVlanModeSpecifies the multicast filter mode for each VLAN.rw Enumeration .dlink-Dgs3420Proj-Dgs3420-28PC.2.17.1.1.2 |
swL2MgmtMIBTraps OBJECT IDENTIFIER .dlink-Dgs3420Proj-Dgs3420-28PC.2.100 |
swL2Notify OBJECT IDENTIFIER .dlink-Dgs3420Proj-Dgs3420-28PC.2.100.1 |
swL2NotifyMgmt OBJECT IDENTIFIER .dlink-Dgs3420Proj-Dgs3420-28PC.2.100.1.1 |
swL2macNotificationSeverityIndicates the level of macNotification detection.rw AgentNotifyLevel (DLINK-ID-REC-MIB) .dlink-Dgs3420Proj-Dgs3420-28PC.2.100.1.1.1 |
swL2PortSecurityViolationSeverityIndicates the level of PortSecurityViolation detection.rw AgentNotifyLevel (DLINK-ID-REC-MIB) .dlink-Dgs3420Proj-Dgs3420-28PC.2.100.1.1.2 |
swL2NotifyPrefix OBJECT IDENTIFIER .dlink-Dgs3420Proj-Dgs3420-28PC.2.100.1.2 |
swL2NotifFirmware OBJECT IDENTIFIER .dlink-Dgs3420Proj-Dgs3420-28PC.2.100.1.2.0 |
swL2macNotificationThis trap indicates the MAC address variations in the address table . NOTIFICATION-TYPE .dlink-Dgs3420Proj-Dgs3420-28PC.2.100.1.2.0.1 |
swL2PortSecurityViolationTrapWhen the port_security trap is enabled, new MAC addresses that violate
the pre-defined port security configuration will trigger trap messages
to be sent out. NOTIFICATION-TYPE .dlink-Dgs3420Proj-Dgs3420-28PC.2.100.1.2.0.2 |
swl2NotificationBidings OBJECT IDENTIFIER .dlink-Dgs3420Proj-Dgs3420-28PC.2.100.1.2.1 |
swL2macNotifyInfoThis object indicates information about the last time the system rebooted.ro OCTET STRING .dlink-Dgs3420Proj-Dgs3420-28PC.2.100.1.2.1.1 |
swL2PortSecurityViolationMacThis object indicates the MAC address that violated the port security configuration.ro MacAddress (SNMPv2-TC) .dlink-Dgs3420Proj-Dgs3420-28PC.2.100.1.2.1.2 |