DES3828P-SWL3MGMT-MIB
The Structure of Layer 3 Network Management Information for the proprietary enterprise.
Main OID:
swL3MgmtMIB.1.3.6.1.4.1.171.11.69.3.3
181
Objects
Active
Status
5
Dependencies
Imported Objects
Objects
181 total| Object Name |
|---|
swL3MgmtMIBThe Structure of Layer 3 Network Management Information for the
proprietary enterprise. MODULE-IDENTITY .1.3.6.1.4.1.171.11.69.3.3 |
swL3DevMgmt OBJECT IDENTIFIER .1.3.6.1.4.1.171.11.69.3.3.1 |
swL3DevCtrl OBJECT IDENTIFIER .1.3.6.1.4.1.171.11.69.3.3.1.1 |
swL3DevCtrlRIPStateThis object indicates if the Routing Information Protocol (RIP)
version 2 function is enabled or disabled.rw Enumeration .1.3.6.1.4.1.171.11.69.3.3.1.1.1 |
swL3DevCtrlOSPFStateThis object indicates if the OSPF protocol is enabled or disabled.rw Enumeration .1.3.6.1.4.1.171.11.69.3.3.1.1.2 |
swL3DevCtrlDVMRPStateThis object indicates if the DVMRP protocol is enabled or disabled.rw Enumeration .1.3.6.1.4.1.171.11.69.3.3.1.1.3 |
swL3DevCtrlPIMStateThis object indicates if the PIM protocol is enabled or disabled.rw Enumeration .1.3.6.1.4.1.171.11.69.3.3.1.1.4 |
swL3DevCtrlVRRPStateThis object indicates if the VRRP protocol is enabled or disabled.rw Enumeration .1.3.6.1.4.1.171.11.69.3.3.1.1.5 |
swL3DevCtrlOSPFECMPStateThis object indicates if the ECMP for OSPF protocol is enabled or disabled.rw Enumeration .1.3.6.1.4.1.171.11.69.3.3.1.1.8 |
swL3IpMgmt OBJECT IDENTIFIER .1.3.6.1.4.1.171.11.69.3.3.2 |
swL3IpCtrlMgmt OBJECT IDENTIFIER .1.3.6.1.4.1.171.11.69.3.3.2.1 |
swL3IpCtrlTableThis table contains the IP interface information. SEQUENCE OF SwL3IpCtrlEntry .1.3.6.1.4.1.171.11.69.3.3.2.1.1 |
swL3IpCtrlEntryA list of information about a specific IP interface. SwL3IpCtrlEntry .1.3.6.1.4.1.171.11.69.3.3.2.1.1.1 |
swL3IpCtrlIpAddrThe IP address of the interface. This object can only contain the
value of the unicast IP address. IpAddress .1.3.6.1.4.1.171.11.69.3.3.2.1.1.1.1 |
swL3IpCtrlIfIndexThis object uniquely identifies the IP interface number in the
swL3IpCtrlTable.ro INTEGER .1.3.6.1.4.1.171.11.69.3.3.2.1.1.1.2 |
swL3IpCtrlInterfaceNameThis object indicates the name of the IP interface.rw DisplayString .1.3.6.1.4.1.171.11.69.3.3.2.1.1.1.3 |
swL3IpCtrlIpSubnetMaskThe IP net mask for this interface.rw IpAddress .1.3.6.1.4.1.171.11.69.3.3.2.1.1.1.4 |
swL3IpCtrlVlanNameThis object indicates the IP control entry's VLAN name. The
VLAN name in each entry must be unique in the IP Control Table.rw DisplayString .1.3.6.1.4.1.171.11.69.3.3.2.1.1.1.5 |
swL3IpCtrlModeThis object indicates the IP operation mode.
other (1) - This entry is currently in use but the conditions
under which it will remain so are different from each of the
following values.
manual (2) - The IP address will be set manually.
bootp (3) - The IP address will be set automatically from the BOOTP
server.
dhcp (4) - The IP address will be set automatically from the DHCP
server.rw Enumeration .1.3.6.1.4.1.171.11.69.3.3.2.1.1.1.6 |
swL3IpCtrlSecondaryWhen this is true (1) the IP address is the secondary IP. When
false (2), the IP address is the primary IP.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.171.11.69.3.3.2.1.1.1.7 |
swL3IpCtrlStateThis variable displays the status of the entry. The status used
for creating, modifying, and deleting instances of objects is
in this table.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.171.11.69.3.3.2.1.1.1.8 |
swL3IpCtrlOperStateThe current operational state of the IP interface.ro Enumeration .1.3.6.1.4.1.171.11.69.3.3.2.1.1.1.9 |
swL3IpCtrlProxyARPStateThis object indicates if the Proxy ARP function is enabled or
disabled.rw Enumeration .1.3.6.1.4.1.171.11.69.3.3.2.1.1.1.10 |
swL3VirtualIpCtrlTableThis table contains the virtual IP interface information. SEQUENCE OF SwL3VirtualIpCtrlEntry .1.3.6.1.4.1.171.11.69.3.3.2.1.2 |
swL3VirtualIpCtrlEntryA list of information about a specific virtual IP interface. SwL3VirtualIpCtrlEntry .1.3.6.1.4.1.171.11.69.3.3.2.1.2.1 |
swL3VirtualIpCtrlInterfaceNameThis object indicates the name of the virtual IP interface. DisplayString .1.3.6.1.4.1.171.11.69.3.3.2.1.2.1.1 |
swL3VirtualIpCtrlIfIndexThis object uniquely identifies the virtual IP interface number in the
swL3VirtualIpCtrlEntry.ro INTEGER .1.3.6.1.4.1.171.11.69.3.3.2.1.2.1.2 |
swL3VirtualIpCtrlIpAddrThe virtual IP address of the interface. This object can only take the
value of the unicast IP address.rw IpAddress .1.3.6.1.4.1.171.11.69.3.3.2.1.2.1.3 |
swL3VirtualIpCtrlIpSubnetMaskThe net mask for this interface.ro IpAddress .1.3.6.1.4.1.171.11.69.3.3.2.1.2.1.4 |
swL3VirtualIpCtrlOperStateThe current operational state of the virtual IP interface.ro Enumeration .1.3.6.1.4.1.171.11.69.3.3.2.1.2.1.5 |
swL3VirtualIpCtrlStateThis variable displays the status of the entry. The status used
for creating, modifying, and deleting instances of the objects
in this table.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.171.11.69.3.3.2.1.2.1.9 |
swL3IpFdbMgmt OBJECT IDENTIFIER .1.3.6.1.4.1.171.11.69.3.3.2.2 |
swL3IpFdbInfoTableA table that contains forwarding and/or filtering information.
This information is used by the switch to determine how to
propagate the received IP packets. SEQUENCE OF SwL3IpFdbInfoEntry .1.3.6.1.4.1.171.11.69.3.3.2.2.1 |
swL3IpFdbInfoEntryInformation about a specific IP address for which the bridge
has some forwarding and/or filtering information. SwL3IpFdbInfoEntry .1.3.6.1.4.1.171.11.69.3.3.2.2.1.1 |
swL3IpFdbInfoIpAddrAn IP address for which the switch has forwarding and/or filtering
information.ro IpAddress .1.3.6.1.4.1.171.11.69.3.3.2.2.1.1.1 |
swL3IpFdbInfoIpSubnetMaskAn IP net mask for this interface for which the switch has
forwarding and/or filtering information.ro IpAddress .1.3.6.1.4.1.171.11.69.3.3.2.2.1.1.2 |
swL3IpFdbInfoPortEither the value '0', or the port number of the packet that has an
IP address equal to the value of the corresponding instance of
swL3IpFdbInfoIpAddr that has been seen. A value of '0' indicates that the
port number has not been learned, but that the switch does have some
forwarding/filtering information about this address.ro INTEGER .1.3.6.1.4.1.171.11.69.3.3.2.2.1.1.3 |
swL3IpFdbInfoTypeThe status of this entry.ro Enumeration .1.3.6.1.4.1.171.11.69.3.3.2.2.1.1.4 |
swL3IpArpAgingTimeThe timeout period in minutes for aging out dynamically learned
ARP information.rw INTEGER .1.3.6.1.4.1.171.11.69.3.3.2.4 |
swL3IpStaticRouteTableThis entity's IP static routing table. SEQUENCE OF SwL3IpStaticRouteEntry .1.3.6.1.4.1.171.11.69.3.3.2.5 |
swL3IpStaticRouteEntryA particular route to a particular destination, under a particular policy.
Once an entry is built, it shouldn't be modified. That is, it just supports a
create or delete action. SwL3IpStaticRouteEntry .1.3.6.1.4.1.171.11.69.3.3.2.5.1 |
swL3IpStaticRouteDestThe destination IP address of this route.
This object will not take a Multicast (Class D)
address value.
Any assignment (implicit or otherwise) of an
instance of this object with a value of x must
be rejected if the bitwise logical-AND of x with
the value of the corresponding instance of the
swL3IpStaticRouteMask object is not equal to x.ro IpAddress .1.3.6.1.4.1.171.11.69.3.3.2.5.1.1 |
swL3IpStaticRouteMaskIndicates that the mask is to be logical-ANDed with
the destination address before being compared to
the value in the swL3IpStaticRouteDest field.
For those systems that do not support arbitrary
subnet masks, an agent constructs the value of
the swL3IpStaticRouteMask by referring to the IP
Address Class.
Any assignment (implicit or otherwise) of an
instance of this object to the value x must be
rejected if the bitwise logical-AND of x with
the value of the corresponding instance of the
swL3IpStaticRouteDest object is not equal to
swL3IpStaticRouteDest.ro IpAddress .1.3.6.1.4.1.171.11.69.3.3.2.5.1.2 |
swL3IpStaticRouteBkupStateThe routing state for this route. The value should be
primary (1) or backup (2).ro Enumeration .1.3.6.1.4.1.171.11.69.3.3.2.5.1.3 |
swL3IpStaticRouteNextHopOn remote routes, the address of the next system
route; Otherwise, 0.0.0.0.rw IpAddress .1.3.6.1.4.1.171.11.69.3.3.2.5.1.4 |
swL3IpStaticRouteMetricThe routing metric for this route.rw INTEGER .1.3.6.1.4.1.171.11.69.3.3.2.5.1.5 |
swL3IpStaticRouteStatusThis object indicates the status of this entry.
other (1) - This entry is currently in use but the conditions
under which it will remain so are different from each of
the following values.
invalid (2) - If this value is written to the object, the
corresponding entry will be removed from the table.
Valid (3) - This entry will reside in the table.rw Enumeration .1.3.6.1.4.1.171.11.69.3.3.2.5.1.6 |
swL3RelayMgmt OBJECT IDENTIFIER .1.3.6.1.4.1.171.11.69.3.3.3 |
swL3RelayBootpMgmt OBJECT IDENTIFIER .1.3.6.1.4.1.171.11.69.3.3.3.1 |
swL3RelayBootpStateThis object indicates if the BOOTP Relay function is enabled
or disabled.rw Enumeration .1.3.6.1.4.1.171.11.69.3.3.3.1.1 |
swL3RelayBootpHopCountThis object indicates the maximum number of router hops that
the BOOTP packets can cross.rw INTEGER .1.3.6.1.4.1.171.11.69.3.3.3.1.2 |
swL3RelayBootpTimeThresholdThis object indicates the minimum time in seconds within which
the switch must relay the BOOTP request. If this time is
exceeded, the switch will drop the BOOTP packet.rw INTEGER .1.3.6.1.4.1.171.11.69.3.3.3.1.3 |
swL3RelayBootpOption82StateThis object indicates if the DHCP relay agent information
option 82 function is enabled or disabled.rw Enumeration .1.3.6.1.4.1.171.11.69.3.3.3.1.4 |
swL3RelayBootpOption82CheckThis object indicates if the checking mechanism of DHCP
relay agent information option 82 is enabled or disabled.rw Enumeration .1.3.6.1.4.1.171.11.69.3.3.3.1.5 |
swL3RelayBootpOption82PolicyThis object indicates the reforwarding policy of DHCP relay agent
information option 82.
replace (1) - Replace the existing option 82 field in messages.
drop (2) - Discard messages with the existing option 82 field.
keep (3) - Retain the existing option 82 field in messages.rw Enumeration .1.3.6.1.4.1.171.11.69.3.3.3.1.6 |
swL3RelayBootpCtrlTableThis table specifies the IP address as a destination to forward
(relay) BOOTP packets to. SEQUENCE OF SwL3RelayBootpCtrlEntry .1.3.6.1.4.1.171.11.69.3.3.3.1.7 |
swL3RelayBootpCtrlEntryA list of information that specifies the IP address of a destination
to forward (relay) BOOTP packets to. SwL3RelayBootpCtrlEntry .1.3.6.1.4.1.171.11.69.3.3.3.1.7.1 |
swL3RelayBootpCtrlInterfaceNameThe name of the IP interface.ro DisplayString .1.3.6.1.4.1.171.11.69.3.3.3.1.7.1.1 |
swL3RelayBootpCtrlServerThe BOOTP server IP address.ro IpAddress .1.3.6.1.4.1.171.11.69.3.3.3.1.7.1.2 |
swL3RelayBootpCtrlStateThis object indicates the status of this entry.
other (1) - This entry is currently in use but the conditions
under which it will remain so are different from each of
the following values.
invalid (2) - If this value is written to the object, the
corresponding entry will be removed from the table.
valid (3) - This entry will reside in the table.rw Enumeration .1.3.6.1.4.1.171.11.69.3.3.3.1.7.1.3 |
swL3RelayDnsMgmt OBJECT IDENTIFIER .1.3.6.1.4.1.171.11.69.3.3.3.2 |
swL3RelayDnsStateThis object indicates if the DNS Relay function is enabled
or disabled.rw Enumeration .1.3.6.1.4.1.171.11.69.3.3.3.2.1 |
swL3RelayDnsPrimaryServerThis object indicates the address of the primary DNS server.rw IpAddress .1.3.6.1.4.1.171.11.69.3.3.3.2.2 |
swL3RelayDnsSecondaryServerThis object indicates the address of the secondary DNS server.rw IpAddress .1.3.6.1.4.1.171.11.69.3.3.3.2.3 |
swL3RelayDnsCacheStateThis object indicates if the DNS Relay cache is enabled or
disabled.rw Enumeration .1.3.6.1.4.1.171.11.69.3.3.3.2.4 |
swL3RelayDnsStaticTableStateThis object indicates if the DNS Relay static table is
enabled or disabled.rw Enumeration .1.3.6.1.4.1.171.11.69.3.3.3.2.5 |
swL3RelayDnsCtrlTableThis table display the current DNS relay static table. SEQUENCE OF SwL3RelayDnsCtrlEntry .1.3.6.1.4.1.171.11.69.3.3.3.2.6 |
swL3RelayDnsCtrlEntryA list of information displaying the current DNS relay
static table. SwL3RelayDnsCtrlEntry .1.3.6.1.4.1.171.11.69.3.3.3.2.6.1 |
swL3RelayDnsCtrlDomainNameThe domain name of this entry.ro DisplayString .1.3.6.1.4.1.171.11.69.3.3.3.2.6.1.1 |
swL3RelayDnsCtrlIpAddrThe IP address of this entry.ro IpAddress .1.3.6.1.4.1.171.11.69.3.3.3.2.6.1.2 |
swL3RelayDnsCtrlStateThis object indicates the status of this entry.
other (1) - This entry is currently in use but the conditions
under which it will remain so are different from each of
the following values.
invalid (2) - If this value is written to the object, the
corresponding entry will be removed from the table.
valid (3) - This entry will reside in the table.rw Enumeration .1.3.6.1.4.1.171.11.69.3.3.3.2.6.1.3 |
swL3Md5TableThis table display the current MD5 key table. SEQUENCE OF SwL3Md5Entry .1.3.6.1.4.1.171.11.69.3.3.4 |
swL3Md5EntryA list of information displaying the current MD5 key table. SwL3Md5Entry .1.3.6.1.4.1.171.11.69.3.3.4.1 |
swL3Md5KeyIdThe MD5 key ID.ro INTEGER .1.3.6.1.4.1.171.11.69.3.3.4.1.1 |
swL3Md5KeyAn MD5 password of up to 16 bytes.rw DisplayString .1.3.6.1.4.1.171.11.69.3.3.4.1.2 |
swL3Md5RowStatusThis object indicates the status of this entry.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.171.11.69.3.3.4.1.3 |
swL3RouteRedistriTableRoute redistribution allows routers on the network that are
running different routing protocols to exchange routing
information. This is accomplished by comparing the routes stored
in the various routers routing tables and assigning appropriate
metrics. This information is then exchanged among the various
routers according to the individual routers current routing
protocol. SEQUENCE OF SwL3RouteRedistriEntry .1.3.6.1.4.1.171.11.69.3.3.5 |
swL3RouteRedistriEntryA list of information displaying the route redistribution table. SwL3RouteRedistriEntry .1.3.6.1.4.1.171.11.69.3.3.5.1 |
swL3RouteRedistriSrcProtocolAllows the selection of the protocol for the source device.ro Enumeration .1.3.6.1.4.1.171.11.69.3.3.5.1.1 |
swL3RouteRedistriDstProtocolAllows the selection of the protocol for the destination device.ro Enumeration .1.3.6.1.4.1.171.11.69.3.3.5.1.2 |
swL3RouteRedistriTypeAllows the selection of one of the methods for calculating
the metric value.rw Enumeration .1.3.6.1.4.1.171.11.69.3.3.5.1.3 |
swL3RouteRedistriMetricAllows the entry of an OSPF interface cost. This is analogous
to a Hop Count in the RIP routing protocol. The value '0'
indicates the default value.rw INTEGER .1.3.6.1.4.1.171.11.69.3.3.5.1.4 |
swL3RouteRedistriRowStatusThis object indicates the status of this entry.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.171.11.69.3.3.5.1.5 |
swL3OspfHostTableThe list of hosts and their metrics that the router will
advertise as host routes. SEQUENCE OF SwL3OspfHostEntry .1.3.6.1.4.1.171.11.69.3.3.6 |
swL3OspfHostEntryA metric to be advertised, for a given type of service, when a
given host is reachable. SwL3OspfHostEntry .1.3.6.1.4.1.171.11.69.3.3.6.1 |
swL3OspfHostIpAddressThe IP address of the host.ro IpAddress .1.3.6.1.4.1.171.11.69.3.3.6.1.1 |
swL3OspfHostTOSThe Type of Service for the route being configured.ro TOSType (OSPF-MIB) .1.3.6.1.4.1.171.11.69.3.3.6.1.2 |
swL3OspfHostMetricThe metric to be advertised.rw Metric (OSPF-MIB) .1.3.6.1.4.1.171.11.69.3.3.6.1.3 |
swL3OspfHostAreaIDThe area of the host entry to be found within. By default, this is the
area that a subsuming OSPF interface is in, or 0.0.0.0rw AreaID (OSPF-MIB) .1.3.6.1.4.1.171.11.69.3.3.6.1.4 |
swL3OspfHostStatusThis variable displays the status of the entry. Setting it to
'invalid' has the effect of rendering it inoperative. The internal
effect (row removal) is implementation dependent.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.171.11.69.3.3.6.1.5 |
swL3ospfVirtIfTableInformation about this router's virtual inter-
faces. SEQUENCE OF SwL3OspfVirtIfEntry .1.3.6.1.4.1.171.11.69.3.3.7 |
swL3ospfVirtIfEntryInformation about a single virtual interface. SwL3OspfVirtIfEntry .1.3.6.1.4.1.171.11.69.3.3.7.1 |
swL3ospfVirtIfAreaIdThe transit area that the virtual link
traverses. By definition, this is not 0.0.0.0ro AreaID (OSPF-MIB) .1.3.6.1.4.1.171.11.69.3.3.7.1.1 |
swL3ospfVirtIfNeighborThe router ID of the virtual neighbor.ro RouterID (OSPF-MIB) .1.3.6.1.4.1.171.11.69.3.3.7.1.2 |
swL3ospfVirtIfTransitDelayThe estimated number of seconds it takes to
transmit a link-state update packet over this
interface.rw UpToMaxAge (OSPF-MIB) .1.3.6.1.4.1.171.11.69.3.3.7.1.3 |
swL3ospfVirtIfRetransIntervalThe number of seconds between link-state
advertisement retransmissions for
adjacencies belonging to this interface. This
value is also used when retransmitting database
description and link-state request packets.
This value should be well over the expected
round-trip time.rw UpToMaxAge (OSPF-MIB) .1.3.6.1.4.1.171.11.69.3.3.7.1.4 |
swL3ospfVirtIfHelloIntervalThe length of time, in seconds, between the
hello packets that the router sends on the
interface. This value must be the same for
the virtual neighbor.rw HelloRange (OSPF-MIB) .1.3.6.1.4.1.171.11.69.3.3.7.1.5 |
swL3ospfVirtIfRtrDeadIntervalThe number of seconds that a router's hello
packets have not been seen before it's neigh-
bors declare the router down. This should be
some multiple of the hello interval. This
value must be the same for the virtual neigh-
bor.rw PositiveInteger (OSPF-MIB) .1.3.6.1.4.1.171.11.69.3.3.7.1.6 |
swL3ospfVirtIfStateOSPF virtual interface states.ro Enumeration .1.3.6.1.4.1.171.11.69.3.3.7.1.7 |
swL3ospfVirtIfEventsThe number of state changes or error events on
this virtual linkro Counter32 .1.3.6.1.4.1.171.11.69.3.3.7.1.8 |
swL3ospfVirtIfAuthTypeThe authentication type specified for a virtu-
al interface. Additional authentication types
may be assigned locally.rw INTEGER .1.3.6.1.4.1.171.11.69.3.3.7.1.9 |
swL3ospfVirtIfAuthKeyIf authentication type is simplePassword, the
device will left adjust and zero fill to 8 oc-
tets.
Note that unauthenticated interfaces need no
authentication key, and simple password authen-
tication cannot use a key of more than 8 oc-
tets. Larger keys are useful only with authen-
tication mechanisms not specified in this docu-
ment.rw OCTET STRING .1.3.6.1.4.1.171.11.69.3.3.7.1.10 |
swL3ospfVirtIfAuthKeyIDThe MD5 key ID.rw INTEGER .1.3.6.1.4.1.171.11.69.3.3.7.1.11 |
swL3ospfVirtIfStatusThis variable displays the status of the en-
try. Setting it to 'invalid' has the effect of
rendering it inoperative. The internal effect
(row removal) is implementation dependent.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.171.11.69.3.3.7.1.12 |
swL3ospfIfTableThe OSPF Interface Table describes the inter-
faces from the viewpoint of OSPF. SEQUENCE OF SwL3OspfIfEntry .1.3.6.1.4.1.171.11.69.3.3.8 |
swL3ospfIfEntryThe OSPF interface entry describes one inter-
face from the viewpoint of OSPF. SwL3OspfIfEntry .1.3.6.1.4.1.171.11.69.3.3.8.1 |
swL3ospfIfIpAddressThe IP address of this OSPF interface.ro IpAddress .1.3.6.1.4.1.171.11.69.3.3.8.1.1 |
swL3ospfAddressLessIfFor the purpose of easing the instancing of
addressed and addressless interfaces; This
variable takes the value 0 on interfaces with
IP addresses and the corresponding value of
ifIndex for interfaces having no IP address.ro Integer32 .1.3.6.1.4.1.171.11.69.3.3.8.1.2 |
swL3ospfIfAreaIdA 32-bit integer uniquely identifying the area
to which the interface connects. Area ID
0.0.0.0 is used for the OSPF backbone.rw AreaID (OSPF-MIB) .1.3.6.1.4.1.171.11.69.3.3.8.1.3 |
swL3ospfIfTypeThe OSPF interface type.
By way of default, this field may be intuited
from the corresponding value of ifType. Broad-
cast LANs, such as Ethernet and IEEE 802.5,
take the value 'broadcast', X.25 and similar
technologies take the value 'nbma' and links
that are definitively point-to-point take the
value 'pointToPoint'.rw Enumeration .1.3.6.1.4.1.171.11.69.3.3.8.1.4 |
swL3ospfIfAdminStatThe OSPF interface's administrative status.
The value formed on the interface, and the in-
terface will be advertised as an internal route
to some areas. The value 'disabled' denotes
that the interface is external to OSPF.rw Status (OSPF-MIB) .1.3.6.1.4.1.171.11.69.3.3.8.1.5 |
swL3ospfIfRtrPriorityThe priority of this interface. Used in
multi-access networks, this field is used by
the designated router election algorithm. The
value 0 signifies that the router is not eligi-
ble to become the designated router on this
particular network. In the event of a tie in
this value, routers will use their router ID as
a tie breaker.rw DesignatedRouterPriority (OSPF-MIB) .1.3.6.1.4.1.171.11.69.3.3.8.1.6 |
swL3ospfIfTransitDelayThe estimated number of seconds it takes to
transmit a link state update packet over this
interface.rw UpToMaxAge (OSPF-MIB) .1.3.6.1.4.1.171.11.69.3.3.8.1.7 |
swL3ospfIfRetransIntervalThe number of seconds between link-state ad-
vertisement retransmissions, for adjacencies
belonging to this interface. This value is
also used when retransmitting database descrip-
tion and link-state request packets.rw UpToMaxAge (OSPF-MIB) .1.3.6.1.4.1.171.11.69.3.3.8.1.8 |
swL3ospfIfHelloIntervalThe length of time, in seconds, between the
hello packets that the router sends on the in-
terface. This value must be the same for all
routers attached to a common network.rw HelloRange (OSPF-MIB) .1.3.6.1.4.1.171.11.69.3.3.8.1.9 |
swL3ospfIfRtrDeadIntervalThe number of seconds that a router's Hello
packets have not been seen before it's neigh-
bors declare the router down. This should be
some multiple of the hello interval. This
value must be the same for all routers attached
to a common network.rw PositiveInteger (OSPF-MIB) .1.3.6.1.4.1.171.11.69.3.3.8.1.10 |
swL3ospfIfPollIntervalThe larger time interval, in seconds, between
the hello packets sent to an inactive non-
broadcast multi-access neighbor.rw PositiveInteger (OSPF-MIB) .1.3.6.1.4.1.171.11.69.3.3.8.1.11 |
swL3ospfIfStateThe OSPF interface state.ro Enumeration .1.3.6.1.4.1.171.11.69.3.3.8.1.12 |
swL3ospfIfDesignatedRouterThe IP address of the designated router.ro IpAddress .1.3.6.1.4.1.171.11.69.3.3.8.1.13 |
swL3ospfIfBackupDesignatedRouterThe IP address of the backup designated
router.ro IpAddress .1.3.6.1.4.1.171.11.69.3.3.8.1.14 |
swL3ospfIfEventsThe number of times this OSPF interface has
changed its state, or when an error has occurred.ro Counter32 .1.3.6.1.4.1.171.11.69.3.3.8.1.15 |
swL3ospfIfMulticastForwardingThe way multicasts should be forwarded on
this interface; not forwarded, forwarded
as data link multicasts, or forwarded as data link
unicasts. Data link multicasting is not meaning-
ful on point-to-point and NBMA interfaces, and
setting ospfMulticastForwarding to 0 effective-
ly disables all multicast forwarding.rw Enumeration .1.3.6.1.4.1.171.11.69.3.3.8.1.16 |
swL3ospfIfDemandIndicates whether Demand OSPF procedures (hel-
lo supression to FULL neighbors and setting the
DoNotAge flag on proogated LSAs) should be per-
formed on this interface.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.171.11.69.3.3.8.1.17 |
swL3ospfIfAuthTypeThe authentication type specified for an in-
terface. Additional authentication types may
be assigned locally.rw INTEGER .1.3.6.1.4.1.171.11.69.3.3.8.1.18 |
swL3ospfIfAuthKeyThe Authentication Key. If the Area's Author-
ization Type is simplePassword, and the key
length is shorter than 8 octets, the agent will
left adjust and zero fill to 8 octets.
Note that unauthenticated interfaces need no
authentication key, and simple password authen-
tication cannot use a key of more than 8 oc-
tets. Larger keys are useful only with authen-
tication mechanisms not specified in this docu-
ment.
When read, ospfIfAuthKey will always return a
zero length Octet String.rw OCTET STRING .1.3.6.1.4.1.171.11.69.3.3.8.1.19 |
swL3ospfIfAuthKeyIDThe MD5 key ID.rw INTEGER .1.3.6.1.4.1.171.11.69.3.3.8.1.20 |
swL3ospfIfStatusThis variable displays the status of the entry.
Setting it to 'invalid' has the effect of
rendering it inoperative. The internal effect
(row removal) is implementation dependent.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.171.11.69.3.3.8.1.21 |
swL3RoutePreference OBJECT IDENTIFIER .1.3.6.1.4.1.171.11.69.3.3.9 |
swL3RoutePreferenceRIPUsed to configure the RIP route preference.rw INTEGER .1.3.6.1.4.1.171.11.69.3.3.9.1 |
swL3RoutePreferenceOSPFIntraUsed to configure the OSPF intra route preference.rw INTEGER .1.3.6.1.4.1.171.11.69.3.3.9.2 |
swL3RoutePreferenceStaticUsed to configure the static route preference.rw INTEGER .1.3.6.1.4.1.171.11.69.3.3.9.3 |
swL3RoutePreferenceLocalUsed to read the local route preference.ro INTEGER .1.3.6.1.4.1.171.11.69.3.3.9.4 |
swL3RoutePreferenceOSPFInterUsed to configure the OSPF inter route preference.rw INTEGER .1.3.6.1.4.1.171.11.69.3.3.9.5 |
swL3RoutePreferenceOSPFExtT1Used to configure the OSPF ExtT1 route preference.rw INTEGER .1.3.6.1.4.1.171.11.69.3.3.9.6 |
swL3RoutePreferenceOSPFExtT2Used to configure the OSPF ExtT2 route preference.rw INTEGER .1.3.6.1.4.1.171.11.69.3.3.9.7 |
swL3PimMgmt OBJECT IDENTIFIER .1.3.6.1.4.1.171.11.69.3.3.11 |
swL3PimCbsrInfoMgmt OBJECT IDENTIFIER .1.3.6.1.4.1.171.11.69.3.3.11.1 |
swL3pimCbsrBootStrapPeriodAt the elected BSR, this is the interval between originating bootstrap
messages, and should be equal to 60 seconds.rw Integer32 .1.3.6.1.4.1.171.11.69.3.3.11.1.1 |
swL3pimCbsrHashMaskLenThe length (in bits) of the mask to use in the hash function.
For IPv4 we recommend a value of 30. For IPv6 we recommand a value of 126.rw Integer32 .1.3.6.1.4.1.171.11.69.3.3.11.1.2 |
swL3pimCbsrTableThe PIM CBSR Table contains the CBSR related information, like
interface and priority. SEQUENCE OF SwL3pimCbsrEntry .1.3.6.1.4.1.171.11.69.3.3.11.1.3 |
swL3pimCbsrEntryAn entry in the PIM CBSR Table. SwL3pimCbsrEntry .1.3.6.1.4.1.171.11.69.3.3.11.1.3.1 |
swL3pimCbsrInterfaceThe ifIndex value of this PIM interface. InterfaceIndex (IF-MIB) .1.3.6.1.4.1.171.11.69.3.3.11.1.3.1.1 |
swL3pimCbsrPriorityThe preference value for the local interface as a candidate
bootstrap router. The value of -1 is used to indicate that
the local interface is not a candidate BSR interface.rw Integer32 (-1..255) .1.3.6.1.4.1.171.11.69.3.3.11.1.3.1.2 |
swL3pimCandidateRPMgmt OBJECT IDENTIFIER .1.3.6.1.4.1.171.11.69.3.3.11.2 |
swL3pimCandidateRPHoldtimeFor C-RPs, this is the holdtime specified in the C-RP-Adv message,
and is used by the BSR to time out RPs. This should be set to 2.5 *
[C-RP-Adv-Period]. Default: 150 seconds.rw Integer32 .1.3.6.1.4.1.171.11.69.3.3.11.2.1 |
swL3pimCandidateRPPriorityThe 'priority' of the included RP, for the corresponding Encoded-Group
Address (if any). The highest priority is '0' (i.e. the lower the value of the
'Priority' field, the higher the priority). This field is stored at the BSR
upon receipt, along with the RP address and corresponding Encoded-Group Address.rw Integer32 .1.3.6.1.4.1.171.11.69.3.3.11.2.2 |
swL3pimCandidateRPWildcardPrefixCntThe number of encoded group addresses included in the message; indicating
the group prefixes for which the C-RP is advertising. A Prefix-Cnt of '0'
implies a prefix of 224.0.0.0 with a mask length of 4; i.e. all multicast
groups. If the C-RP is not configured with Group-prefix information, the
C-RP puts a default value of '0' in this field.rw Integer32 .1.3.6.1.4.1.171.11.69.3.3.11.2.3 |
swL3pimSptMgmt OBJECT IDENTIFIER .1.3.6.1.4.1.171.11.69.3.3.11.3 |
swL3pimLastHopSptThresholdSpecifies a last hop router threshold.rw DisplayString .1.3.6.1.4.1.171.11.69.3.3.11.3.1 |
swL3pimRPSptThresholdSpecifies an RP threshold.rw DisplayString .1.3.6.1.4.1.171.11.69.3.3.11.3.2 |
swL3pimRegChksumIncDataTableThe PIM Register Checksum Including Data Table contains the PIM
register checksum including data information, like RP address and
state. SEQUENCE OF SwL3pimRegChksumIncDataEntry .1.3.6.1.4.1.171.11.69.3.3.11.4 |
swL3pimRegChksumIncDataEntryAn entry in the PIM Register Checksum Including the Data Table. SwL3pimRegChksumIncDataEntry .1.3.6.1.4.1.171.11.69.3.3.11.4.1 |
swL3SwL3pimRegChksumIncDataRpAddrSpecifies the RP address. IpAddress .1.3.6.1.4.1.171.11.69.3.3.11.4.1.1 |
swL3SwL3pimRegChksumIncDataStateThe state of register checksum including the data for RPs.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.171.11.69.3.3.11.4.1.2 |
swL3PimInfoMgmt OBJECT IDENTIFIER .1.3.6.1.4.1.171.11.69.3.3.11.5 |
swL3pimRegisterProbeTimeWhen null registers are used, this is the time between sending a null
register and the register-suppression-timer expiring unless it is restarted
by receiving a register-stop. Thus, a null register would be sent when the
register-suppression-timer reaches this value. Default: 5 seconds.rw Integer32 .1.3.6.1.4.1.171.11.69.3.3.11.5.1 |
swL3pimRegisterSuppressionTimeThis is the mean interval between receiving a register-stop and allowing
registers to be sent again. A lower value means more frequent register bursts
at RP, while a higher value means longer join latency for the new receiver.
Default: 60 seconds.rw Integer32 .1.3.6.1.4.1.171.11.69.3.3.11.5.2 |
swL3pimInfoTableThe PIM Information Table contains PIM related information, like
DR priority. SEQUENCE OF SwL3pimInfoEntry .1.3.6.1.4.1.171.11.69.3.3.11.5.3 |
swL3pimInfoEntryAn entry in the PIM Information Table. SwL3pimInfoEntry .1.3.6.1.4.1.171.11.69.3.3.11.5.3.1 |
swL3pimInterfaceThe ifIndex value of this PIM interface. InterfaceIndex (IF-MIB) .1.3.6.1.4.1.171.11.69.3.3.11.5.3.1.1 |
swL3pimDRPriorityThe DR Priority is a 32-bit unsigned number and the numerically larger
priority is always prefered. A router's idea of the current DR on an interface
can change when a PIM hello message is received, when a neighbor times out,
or when a router's own DR priority changes.rw Unsigned32 .1.3.6.1.4.1.171.11.69.3.3.11.5.3.1.2 |
swL3pimStaticRPTableThe PIM Static RP Table contains the PIM static RP related information,
like group address, group mask, RP address and RP row status. SEQUENCE OF SwL3pimStaticRPEntry .1.3.6.1.4.1.171.11.69.3.3.11.6 |
swL3pimStaticRPEntryAn entry in the PIM Static RP Table. SwL3pimStaticRPEntry .1.3.6.1.4.1.171.11.69.3.3.11.6.1 |
swL3pimStaticRPGroupAddressThe IP multicast group address which, when combined with
swL3pimStaticRPGroupMask, identifies a group prefix for which
the local router will advertise itself as a static RP. IpAddress .1.3.6.1.4.1.171.11.69.3.3.11.6.1.1 |
swL3pimStaticRPGroupMaskThe multicast group address mask which, when combined with
swL3pimStaticRPGroupAddress, identifies a group prefix for which
the local router will advertise itself as a static RP. IpAddress .1.3.6.1.4.1.171.11.69.3.3.11.6.1.2 |
swL3pimStaticRPAddressThe (unicast) address of the interface which will be
advertised as a static RP. IpAddress .1.3.6.1.4.1.171.11.69.3.3.11.6.1.3 |
swL3pimStaticRPRowStatusThe status of this row. New entries may be
created or old entries deleted from this table.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.171.11.69.3.3.11.6.1.4 |
swL3pimActiveRPTableThe PIM Active RP Table contains the PIM active RP
related information, like group address, RP address. SEQUENCE OF SwL3pimActiveRPEntry .1.3.6.1.4.1.171.11.69.3.3.11.7 |
swL3pimActiveRPEntryAn entry (conceptual row) in the swL3pimActiveRPTable. SwL3pimActiveRPEntry .1.3.6.1.4.1.171.11.69.3.3.11.7.1 |
swL3pimActiveRPGroupAddressThe IP multicast group address for which this entry contains
information about the Active-RP. IpAddress .1.3.6.1.4.1.171.11.69.3.3.11.7.1.1 |
swL3pimActiveRPSourceIPAddressThe IP address for which this entry contains information about the
source of multicast data. IpAddress .1.3.6.1.4.1.171.11.69.3.3.11.7.1.2 |
swL3pimActiveRPSourceIPMaskThe IP mask for which this entry contains information about
the source of multicast data. IpAddress .1.3.6.1.4.1.171.11.69.3.3.11.7.1.3 |
swL3pimActiveRPAddressThe IP address of the Active-RP.ro IpAddress .1.3.6.1.4.1.171.11.69.3.3.11.7.1.4 |
swL3OspfDefaultInfoOriginate OBJECT IDENTIFIER .1.3.6.1.4.1.171.11.69.3.3.12 |
swL3OspfDefaultInfoOriginateStateThis object indicates if the Default Info Originate is
enabled or disabled.rw Status (OSPF-MIB) .1.3.6.1.4.1.171.11.69.3.3.12.1 |
swL3OspfDefaultInfoOriginateAlwaysThis object indicates if the always parameter is
enabled or disabled.
If 'swL3OspfDefaultInfoOriginateState' is disabled, this
object returns to the default setting.rw Status (OSPF-MIB) .1.3.6.1.4.1.171.11.69.3.3.12.2 |
swL3OspfDefaultInfoOriginateMettypeThis object indicates the type of AS external route.
If 'swL3OspfDefaultInfoOriginateState' is disabled, this
object returns to the default setting.rw Enumeration .1.3.6.1.4.1.171.11.69.3.3.12.3 |
swL3OspfDefaultInfoOriginateMetricThis object indicates the cost of a default route to
be advertised in OSPF. The range is 0 to 16777214.rw INTEGER .1.3.6.1.4.1.171.11.69.3.3.12.4 |
swL3TraceRouteMgmt OBJECT IDENTIFIER .1.3.6.1.4.1.171.11.69.3.3.13 |
swL3TraceRouteCtrl OBJECT IDENTIFIER .1.3.6.1.4.1.171.11.69.3.3.13.1 |
swL3TraceRoutePKTToCPUStateThis object indicates to control whether to capture
IP packet with zero TTL to CPU.rw Enumeration .1.3.6.1.4.1.171.11.69.3.3.13.1.1 |