DES3810-28-L2MGMT-MIB
The Structure of Layer 2 Network Management Information.
Main OID:
swL2MgmtMIB.1.3.6.1.4.1.171.11.114.1.1.2
131
Objects
Active
Status
5
Dependencies
Imported Objects
Objects
131 total| Object Name |
|---|
swL2MgmtMIBThe Structure of Layer 2 Network Management Information. MODULE-IDENTITY .1.3.6.1.4.1.171.11.114.1.1.2 |
swL2DevMgmt OBJECT IDENTIFIER .1.3.6.1.4.1.171.11.114.1.1.2.1 |
swL2DevInfo OBJECT IDENTIFIER .1.3.6.1.4.1.171.11.114.1.1.2.1.1 |
swDevInfoTotalNumOfPortThe number of ports within this switch. This value is the sum of the ports within this switch.ro INTEGER .1.3.6.1.4.1.171.11.114.1.1.2.1.1.1 |
swDevInfoNumOfPortInUseThe number of ports in this switch connected to the segment or the end stations.ro INTEGER .1.3.6.1.4.1.171.11.114.1.1.2.1.1.2 |
swDevInfoFrontPanelLedStatusThis object is a set of system LED indications. The first six octets are defined as system LED. The first two octets are currently unused and must be set to zero. The third octet indicates the power LED. The fourth octet indicates the console LED. The fifth LED is RPS (Redundancy Power Supply) LED. The sixth LED is Master(Stacking Master Device) LED. For the byte range form 7 to 8, it reflect the MGMT port. Every two bytes are presented to a port. For the byte range from 9 to 56, it reflect the 1~24FE ports. Every two bytes are presented to a port. For the byte range from 57 to 64, it reflect the 25~26GE Combol ports. Every four bytes are presented to a port. The byte range from 57 to 60, it reflect copper ports. The byte range from 61 to 64, it reflect fiber ports. For the byte range from 65 to 72, it reflect the 27~28GE Combol ports. Every four bytes are presented to a port. The byte range from 65 to 68, it reflect copper ports. The byte range from 69 to 72, it reflect fiber ports. Every two bytes are presented to a port. The first byte is presented as the Link/Activity LED. The second byte is presented as the Speed LED. Power LED: 01 = fail/error/non existence 02 = work normal Console LED: 01 = Console LED OFF 02 = Console LED ON RPS LED: 01 = RPS LED OFF 02 = RPS LED ON Master LED: 01 = Master LED OFF 02 = Master LED ON Link/Activity LED : The most significant bit is used for blink/solid: 8 = The LED blinks. The second most significant bit is used for link status: 1 = link fail. 2 = link pass. Speed LED : 01 = 10Mbps. 02 = 100Mbps. 03 = 1000Mbps. The remaining bytes are currently unused and must be 0.ro OCTET STRING .1.3.6.1.4.1.171.11.114.1.1.2.1.1.4 |
swL2DevCtrl OBJECT IDENTIFIER .1.3.6.1.4.1.171.11.114.1.1.2.1.2 |
swL2DevCtrlSnmpTrapStateThis object controls the SNMP trap status.rw Enumeration .1.3.6.1.4.1.171.11.114.1.1.2.1.2.5 |
swL2DevCtrlCleanAllStatisticCounterWhen the object is set to active, all statistical counters will be cleared. If set to normal, no action.rw Enumeration .1.3.6.1.4.1.171.11.114.1.1.2.1.2.6 |
swL2DevCtrlVlanIdOfFDBTblIndicates the VLAN ID to which the Dot1dTpFdbTable belongs; The default value is DEFAULT-VLAN-ID of the system.rw VlanId .1.3.6.1.4.1.171.11.114.1.1.2.1.2.7 |
swL2MACNotifyStateThis object can enable or disable MAC Notification.rw Enumeration .1.3.6.1.4.1.171.11.114.1.1.2.1.2.8 |
swL2MACNotifyHistorySizeThis object indicates the history size of MAC addresses in the MAC Address table. The default value is 1 .rw INTEGER .1.3.6.1.4.1.171.11.114.1.1.2.1.2.9 |
swL2MACNotifyIntervalThis object indicates the time interval, in seconds, which will trigger MAC notification messages.rw INTEGER .1.3.6.1.4.1.171.11.114.1.1.2.1.2.10 |
swL2DevCtrlTelnet OBJECT IDENTIFIER .1.3.6.1.4.1.171.11.114.1.1.2.1.2.14 |
swL2DevCtrlTelnetStateThis object controls the Telnet status.rw Enumeration .1.3.6.1.4.1.171.11.114.1.1.2.1.2.14.1 |
swL2DevCtrlTelnetTcpPortThis object designates TCP ports. When Telnet is disabled, this object is not accessible.rw INTEGER .1.3.6.1.4.1.171.11.114.1.1.2.1.2.14.2 |
swL2DevCtrlManagementVlanIdThis object controls which previously created VLANs are included in the System IP Interface.rw VlanId .1.3.6.1.4.1.171.11.114.1.1.2.1.2.16 |
swL2DevCtrlWeb OBJECT IDENTIFIER .1.3.6.1.4.1.171.11.114.1.1.2.1.2.17 |
swL2DevCtrlWebStateThis object controls the Web status.rw Enumeration .1.3.6.1.4.1.171.11.114.1.1.2.1.2.17.1 |
swL2DevCtrlWebTcpPortThis object designates TCP ports. When Web is disabled, this object is not accessible.rw INTEGER .1.3.6.1.4.1.171.11.114.1.1.2.1.2.17.2 |
swL2DevCtrlLLDPStateSpecifies the state of the LLDP function. When this function is enabled, the switch can start to transmit LLDP packets and receive and process the LLDP packets. The specific function of each port will depend on the per port LLDP setting. For the advertisement of LLDP packets, the switch announces the information to its neighbor through ports. For the receiving of LLDP packets, the switch will learn the information from the LLDP packets advertised from the neighbor in the neighbor table.rw Enumeration .1.3.6.1.4.1.171.11.114.1.1.2.1.2.18 |
swL2DevCtrlLLDPForwardMessageStateWhen lldp is disabled and lldp forward-message is enabled, the received LLDP Data Unit packets will be forwarded.rw Enumeration .1.3.6.1.4.1.171.11.114.1.1.2.1.2.19 |
swL2DevCtrlIpAutoconfigThis object controls the IP auto configuration state.rw Enumeration .1.3.6.1.4.1.171.11.114.1.1.2.1.2.20 |
swL2DevCtrlCFM OBJECT IDENTIFIER .1.3.6.1.4.1.171.11.114.1.1.2.1.2.21 |
swL2DevCtrlCFMStateThis object indicates the CFM global state.rw Enumeration .1.3.6.1.4.1.171.11.114.1.1.2.1.2.21.1 |
swL2DevCtrlCFMPortTableA table containing CFM state of speicified ports. SEQUENCE OF SwL2DevCtrlCFMPortEntry .1.3.6.1.4.1.171.11.114.1.1.2.1.2.21.2 |
swL2DevCtrlCFMPortEntryThe entry of CFM state on speicified ports. SwL2DevCtrlCFMPortEntry .1.3.6.1.4.1.171.11.114.1.1.2.1.2.21.2.1 |
swL2DevCtrlCFMPortIndexThis object indicates the port-num. INTEGER .1.3.6.1.4.1.171.11.114.1.1.2.1.2.21.2.1.1 |
swL2DevCtrlCFMPortStateThis object indicates the CFM state on per-port.rw Enumeration .1.3.6.1.4.1.171.11.114.1.1.2.1.2.21.2.1.2 |
swL2DevCtrlVLANTrunkStateThis indicates the global state of the VLAN trunking feature of the device.rw Enumeration .1.3.6.1.4.1.171.11.114.1.1.2.1.2.22 |
swL2DevAlarm OBJECT IDENTIFIER .1.3.6.1.4.1.171.11.114.1.1.2.1.3 |
swL2DevAlarmNewRootWhen the device has become the new root of the Spanning Tree, this object decides whether to send a new root trap.rw Enumeration .1.3.6.1.4.1.171.11.114.1.1.2.1.3.1 |
swL2DevAlarmTopologyChangeThis object determines whether or not to send a trap message when the switch topology changes. If the object is enabled(3), the topologyChange trap is sent by the device when any of its configured ports transitions from the Learning state to the Forwarding state, or from the Forwarding state to the Blocking state. For the same port transition, the device does not send the trap if this object value is disabled or other.rw Enumeration .1.3.6.1.4.1.171.11.114.1.1.2.1.3.2 |
swL2DevAlarmLinkChangeThis object determines whether or not to send a trap message when the link was changed. If the object is enabled(3), the Link Change trap is sent by the device when any of its ports link change. The device does not send the trap if this object value is disabled or other.rw Enumeration .1.3.6.1.4.1.171.11.114.1.1.2.1.3.3 |
swL2VLANMgmt OBJECT IDENTIFIER .1.3.6.1.4.1.171.11.114.1.1.2.2 |
swL2VlanStaticTableA table containing static configuration information for each VLAN configured into the device by (local or network) management. All entries are permanent and will be restored after the device is reset. SEQUENCE OF SwL2VlanStaticEntry .1.3.6.1.4.1.171.11.114.1.1.2.2.1 |
swL2VlanStaticEntryStatic information for a VLAN configured into the device by (local or network) management. SwL2VlanStaticEntry .1.3.6.1.4.1.171.11.114.1.1.2.2.1.1 |
swL2VlanIndexThe VLAN-ID or other identifier referring to this VLAN. VlanId .1.3.6.1.4.1.171.11.114.1.1.2.2.1.1.1 |
swL2VLANAdvertisementThis object indicates if the advertisement is active or not.rw Enumeration .1.3.6.1.4.1.171.11.114.1.1.2.2.1.1.2 |
swL2PVIDAutoAssignmentStateThis object controls the PVID auto assigment state. If 'Auto-assign PVID' is disabled, PVID can only be changed by PVID configuration (user changes explicitly). The VLAN configuration will not automatically change the PVID. If 'Auto-assign PVID' is enabled, the PVID will be changed by PVID or VLAN configuration. When a user configures a port to VLAN X's untagged membership, this port's PVID will be updated with VLAN X. Using the VLAN list command, PVID is updated as the last item of the VLAN list. When a user removes a port from the untagged membership of the PVID's VLAN, the port's PVID will be assigned 'default VLAN'.rw Enumeration .1.3.6.1.4.1.171.11.114.1.1.2.2.2 |
swL2VlanPortInfoTableA table containing vlan and port role information of each port. SEQUENCE OF SwL2VlanPortInfoEntry .1.3.6.1.4.1.171.11.114.1.1.2.2.3 |
swL2VlanPortInfoEntryThe table entry of vlan port information. SwL2VlanPortInfoEntry .1.3.6.1.4.1.171.11.114.1.1.2.2.3.1 |
swL2VlanPortInfoPortIndexThe port index.ro INTEGER .1.3.6.1.4.1.171.11.114.1.1.2.2.3.1.1 |
swL2VlanPortInfoVidThe VLAN-ID assigned to a special portro INTEGER .1.3.6.1.4.1.171.11.114.1.1.2.2.3.1.2 |
swL2VlanPortInfoPortRoleThe port role of a special port.when none,it means this port is not belong to the vlan.ro Enumeration .1.3.6.1.4.1.171.11.114.1.1.2.2.3.1.3 |
swL2NniGvrpBpduAddressSpecifies the GVRP's BPDU MAC address of NNI port In Q-in-Q status.rw Enumeration .1.3.6.1.4.1.171.11.114.1.1.2.2.7 |
swL2PortMgmt OBJECT IDENTIFIER .1.3.6.1.4.1.171.11.114.1.1.2.3 |
swL2PortInfoTableA table that contains information about every port. SEQUENCE OF SwL2PortInfoEntry .1.3.6.1.4.1.171.11.114.1.1.2.3.1 |
swL2PortInfoEntryA list of information for each port of the device. SwL2PortInfoEntry .1.3.6.1.4.1.171.11.114.1.1.2.3.1.1 |
swL2PortInfoPortIndexThis object indicates the module's port number.(1..Max port number in the module)ro INTEGER .1.3.6.1.4.1.171.11.114.1.1.2.3.1.1.1 |
swL2PortInfoMediumTypeIndicates medium type of the port number.ro Enumeration .1.3.6.1.4.1.171.11.114.1.1.2.3.1.1.2 |
swL2PortInfoUnitIDIndicates ID of the unit in the systemro INTEGER .1.3.6.1.4.1.171.11.114.1.1.2.3.1.1.3 |
swL2PortInfoTypeThis object indicates the connector type of this port.ro Enumeration .1.3.6.1.4.1.171.11.114.1.1.2.3.1.1.4 |
swL2PortInfoLinkStatusThis object indicates the port link status.ro Enumeration .1.3.6.1.4.1.171.11.114.1.1.2.3.1.1.5 |
swL2PortInfoNwayStatusThis object indicates the port speed and duplex mode.ro Enumeration .1.3.6.1.4.1.171.11.114.1.1.2.3.1.1.6 |
swL2PortInfoErrorDisabledThis object indicates the blocking type of this port.ro Enumeration .1.3.6.1.4.1.171.11.114.1.1.2.3.1.1.8 |
swL2PortCtrlTableA table that contains control information about every port. SEQUENCE OF SwL2PortCtrlEntry .1.3.6.1.4.1.171.11.114.1.1.2.3.2 |
swL2PortCtrlEntryA list of control information for each port of the device. SwL2PortCtrlEntry .1.3.6.1.4.1.171.11.114.1.1.2.3.2.1 |
swL2PortCtrlPortIndexThis object indicates the module's port number.(1..Max port number in the module)ro INTEGER .1.3.6.1.4.1.171.11.114.1.1.2.3.2.1.1 |
swL2PortCtrlMediumTypeIndicates medium type of the port number.ro Enumeration .1.3.6.1.4.1.171.11.114.1.1.2.3.2.1.2 |
swL2PortCtrlUnitIndexIndicates ID of the unit in the devicero INTEGER .1.3.6.1.4.1.171.11.114.1.1.2.3.2.1.3 |
swL2PortCtrlAdminStateThis object decides if the port is enabled or disabled.rw Enumeration .1.3.6.1.4.1.171.11.114.1.1.2.3.2.1.4 |
swL2PortCtrlNwayStateChose the port speed, duplex mode, and N-Way function mode.rw Enumeration .1.3.6.1.4.1.171.11.114.1.1.2.3.2.1.5 |
swL2PortCtrlFlowCtrlStateThe flow control mechanism is different between full duplex mode and half duplex mode. For half duplex mode, the jamming signal is asserted. For full duplex mode, IEEE 802.3x flow control function sends PAUSE frames and receives PAUSE frames.rw Enumeration .1.3.6.1.4.1.171.11.114.1.1.2.3.2.1.6 |
swL2PortCtrlLearningStateThis object decides if the port is locked or not.rw Enumeration .1.3.6.1.4.1.171.11.114.1.1.2.3.2.1.7 |
swL2PortCtrlMACNotifyStateThis object sets each port's MAC notification state.rw Enumeration .1.3.6.1.4.1.171.11.114.1.1.2.3.2.1.8 |
swL2PortCtrlMDIXStateThis object configures the MDIX setting of the port.rw Enumeration .1.3.6.1.4.1.171.11.114.1.1.2.3.2.1.10 |
swL2PortCtrlJumboFrameThis object configures the switch's jumbo frame settings.rw Enumeration .1.3.6.1.4.1.171.11.114.1.1.2.3.3 |
swL2PortCtrlJumboFrameMaxSizeThis object describes how many bytes the max jumbo frame is.ro INTEGER .1.3.6.1.4.1.171.11.114.1.1.2.3.4 |
swL2PortCounterCtrlTableA table that used to clear counter information about every port. SEQUENCE OF SwL2PortCounterCtrlEntry .1.3.6.1.4.1.171.11.114.1.1.2.3.6 |
swL2PortCounterCtrlEntryA list of entry used to clear counter information for each port of the device. SwL2PortCounterCtrlEntry .1.3.6.1.4.1.171.11.114.1.1.2.3.6.1 |
swL2PortCounterCtrlPortIndexThis object indicates the module's port number.(1..Max port number in the module)ro INTEGER .1.3.6.1.4.1.171.11.114.1.1.2.3.6.1.1 |
swL2PortCounterClearCtrlThis object indicates if to clear the counters for each port of the device or not.rw Enumeration .1.3.6.1.4.1.171.11.114.1.1.2.3.6.1.2 |
swL2PortErrTableA table that contains error information for each port. SEQUENCE OF SwL2PortErrEntry .1.3.6.1.4.1.171.11.114.1.1.2.3.7 |
swL2PortErrEntryA list of information regarding port errors on the device. SwL2PortErrEntry .1.3.6.1.4.1.171.11.114.1.1.2.3.7.1 |
swL2PortErrPortIndexThis object indicates the module's port number.(1..Max port number in the module).ro INTEGER .1.3.6.1.4.1.171.11.114.1.1.2.3.7.1.1 |
swL2PortErrPortStateThis object indicates the port state is enabled or disabled.ro Enumeration .1.3.6.1.4.1.171.11.114.1.1.2.3.7.1.2 |
swL2PortErrPortConnStatusThis object indicates whether the PortStatus is err-disabled or not.ro Enumeration .1.3.6.1.4.1.171.11.114.1.1.2.3.7.1.3 |
swL2PortErrPortReasonThis object describes if the reason for the port error is STP LBD or Storm control.ro Enumeration .1.3.6.1.4.1.171.11.114.1.1.2.3.7.1.4 |
swL2DhcpRelayMgmt OBJECT IDENTIFIER .1.3.6.1.4.1.171.11.114.1.1.2.8 |
swL2TrunkMgmt OBJECT IDENTIFIER .1.3.6.1.4.1.171.11.114.1.1.2.9 |
swL2TrunkMaxSupportedEntriesMaximum number of entries in the trunk configuration table (swL2TrunkCtrlTable).ro INTEGER .1.3.6.1.4.1.171.11.114.1.1.2.9.1 |
swL2TrunkCurrentNumEntriesCurrent active number of entries in the trunk configuration table.ro INTEGER .1.3.6.1.4.1.171.11.114.1.1.2.9.2 |
swL2TrunkCtrlTableThis table specifies which ports group a set of ports(up to 8) into a single logical link. SEQUENCE OF SwL2TrunkCtrlEntry .1.3.6.1.4.1.171.11.114.1.1.2.9.3 |
swL2TrunkCtrlEntryA list of information that specifies which ports group a set of ports(up to 8) into a single logical link. SwL2TrunkCtrlEntry .1.3.6.1.4.1.171.11.114.1.1.2.9.3.1 |
swL2TrunkIndexThe index number of the logical port trunk group. The trunk group number depends on the existence of unit and module.ro INTEGER .1.3.6.1.4.1.171.11.114.1.1.2.9.3.1.1 |
swL2TrunkMasterPortThe object indicates the master port number of the port trunk entry. When using Port Trunk, you cannot configure the other ports of the group except the master port. Their configuration must be same as the master port (e.g. speed, duplex, enabled/disabled, flow control, and so on).rw INTEGER .1.3.6.1.4.1.171.11.114.1.1.2.9.3.1.3 |
swL2TrunkMemberIndicates the number of ports included in this Trunk group. The trunk port number depends on the existence of the module. The maximum number of ports is 8 for one trunk group.rw PortList .1.3.6.1.4.1.171.11.114.1.1.2.9.3.1.4 |
swL2TrunkFloodingPortThe object indicates the flooding port number of the port trunk entry. The first port of the Trunk group is implicitly configured to be the flooding port.ro INTEGER .1.3.6.1.4.1.171.11.114.1.1.2.9.3.1.5 |
swL2TrunkTypeThis object indicates the type of trunk group. static : is static trunk group lacp : is LACP trunk group .rw Enumeration .1.3.6.1.4.1.171.11.114.1.1.2.9.3.1.6 |
swL2TrunkStateThis object indicates the status of this entry.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.171.11.114.1.1.2.9.3.1.7 |
swL2TrunkAlgorithmThis object configures to part of the packet examined by the switch when selecting the egress port for transmitting load-sharing data.rw Enumeration .1.3.6.1.4.1.171.11.114.1.1.2.9.4 |
swL2TrunkLACPPortTableThis table specifies which ports group a set of ports(up to 8) into a single logical link. SEQUENCE OF SwL2TrunkLACPPortEntry .1.3.6.1.4.1.171.11.114.1.1.2.9.5 |
swL2TrunkLACPPortEntryA list of information specifies which ports group a set of ports(up to 8) into a single logical link. SwL2TrunkLACPPortEntry .1.3.6.1.4.1.171.11.114.1.1.2.9.5.1 |
swL2TrunkLACPPortIndexThe index of logical port LACP.ro INTEGER .1.3.6.1.4.1.171.11.114.1.1.2.9.5.1.1 |
swL2TrunkLACPPortStateThe state of logical port LACP.rw Enumeration .1.3.6.1.4.1.171.11.114.1.1.2.9.5.1.2 |
swL2TrunkVLANTableThis table is used to manage the VLAN trunking feature of the device. SEQUENCE OF SwL2TrunkVLANEntry .1.3.6.1.4.1.171.11.114.1.1.2.9.6 |
swL2TrunkVLANEntryThis object is used to configure the VLAN trunking settings for each port. SwL2TrunkVLANEntry .1.3.6.1.4.1.171.11.114.1.1.2.9.6.1 |
swL2TrunkVLANPortThis object indicates the port being configured.ro INTEGER .1.3.6.1.4.1.171.11.114.1.1.2.9.6.1.1 |
swL2TrunkVLANStateThe state of the logical port LACP.rw Enumeration .1.3.6.1.4.1.171.11.114.1.1.2.9.6.1.2 |
swL2MirrorMgmt OBJECT IDENTIFIER .1.3.6.1.4.1.171.11.114.1.1.2.10 |
swL2MirrorLogicTargetPortThis object indicates which switch port will sniff another port. A trunk port member cannot be configured as a target snooping port. The port number is the sequential (logical) number which is also applied to the bridge MIB, etc.rw INTEGER .1.3.6.1.4.1.171.11.114.1.1.2.10.1 |
swL2MirrorPortSourceIngressThis represents the port where ingress packets will be sniffed.rw PortList .1.3.6.1.4.1.171.11.114.1.1.2.10.2 |
swL2MirrorPortSourceEgressThis represents the port where egress packets will be sniffed.rw PortList .1.3.6.1.4.1.171.11.114.1.1.2.10.3 |
swL2MirrorPortStateThis object indicates the port mirroring state. other(1) - this entry is currently in use but the conditions under which it will remain so are different from each of the following values. disabled(2) - After writing this value to the object, the corresponding entry will be removed from the table. enabled(3) - This entry resides in the table.rw Enumeration .1.3.6.1.4.1.171.11.114.1.1.2.10.4 |
swL2TrafficSegMgmt OBJECT IDENTIFIER .1.3.6.1.4.1.171.11.114.1.1.2.14 |
swL2TrafficSegTableThis table specifies that the port can just forward traffic to the specific port list. SEQUENCE OF SwL2TrafficSegEntry .1.3.6.1.4.1.171.11.114.1.1.2.14.1 |
swL2TrafficSegEntryA list of information which specifies the port with its traffic forwarding list. SwL2TrafficSegEntry .1.3.6.1.4.1.171.11.114.1.1.2.14.1.1 |
swL2TrafficSegPortThe port number of the logical port.ro INTEGER .1.3.6.1.4.1.171.11.114.1.1.2.14.1.1.1 |
swL2TrafficSegForwardPortsThe port list to which the specific port can forward traffic.rw PortList .1.3.6.1.4.1.171.11.114.1.1.2.14.1.1.2 |
swL2MulticastFilterMode OBJECT IDENTIFIER .1.3.6.1.4.1.171.11.114.1.1.2.17 |
swL2MulticastFilterModeVlanTableA table that contains information about VLAN multicast filter mode. SEQUENCE OF SwL2MulticastFilterModeVlanEntry .1.3.6.1.4.1.171.11.114.1.1.2.17.1 |
swL2MulticastFilterModeVlanEntryA list of multicast filter mode information for each VLAN. SwL2MulticastFilterModeVlanEntry .1.3.6.1.4.1.171.11.114.1.1.2.17.1.1 |
swL2MulticastFilterVidIndicates VID for each VLAN.ro INTEGER .1.3.6.1.4.1.171.11.114.1.1.2.17.1.1.1 |
swL2MulticastFilterVlanModeSpecifies multicast filter mode for each VLAN.rw Enumeration .1.3.6.1.4.1.171.11.114.1.1.2.17.1.1.2 |
swL2DhcpLocalRelayMgmt OBJECT IDENTIFIER .1.3.6.1.4.1.171.11.114.1.1.2.24 |
swL2DhcpLocalRelayStateThis object indicates the status of the DHCP local relay function of the switch.rw Enumeration .1.3.6.1.4.1.171.11.114.1.1.2.24.1 |
swL2DhcpLocalRelayVLANTableThis table is used to manage the DHCP local relay status for each VLAN. SEQUENCE OF SwL2DhcpLocalRelayVLANEntry .1.3.6.1.4.1.171.11.114.1.1.2.24.2 |
swL2DhcpLocalRelayVLANEntryThis object lists the current VLANs in the switch and their corresponding DHCP local relay status. SwL2DhcpLocalRelayVLANEntry .1.3.6.1.4.1.171.11.114.1.1.2.24.2.1 |
swL2DhcpLocalRelayVLANIDThis object shows the VIDs of the current VLANS in the switch.ro INTEGER .1.3.6.1.4.1.171.11.114.1.1.2.24.2.1.1 |
swL2DhcpLocalRelayVLANStateThis object indicates the status of the DHCP relay function of the VLAN.rw Enumeration .1.3.6.1.4.1.171.11.114.1.1.2.24.2.1.2 |
swL2MgmtMIBTraps OBJECT IDENTIFIER .1.3.6.1.4.1.171.11.114.1.1.2.100 |
swL2Notify OBJECT IDENTIFIER .1.3.6.1.4.1.171.11.114.1.1.2.100.1 |
swL2NotifyMgmt OBJECT IDENTIFIER .1.3.6.1.4.1.171.11.114.1.1.2.100.1.1 |
swL2NotifyPrefix OBJECT IDENTIFIER .1.3.6.1.4.1.171.11.114.1.1.2.100.1.2 |
swL2NotifFirmware OBJECT IDENTIFIER .1.3.6.1.4.1.171.11.114.1.1.2.100.1.2.0 |
swL2macNotificationThis trap indicates the MAC addresses variation in address table . NOTIFICATION-TYPE .1.3.6.1.4.1.171.11.114.1.1.2.100.1.2.0.1 |
swL2PortSecurityViolationTrapWhen the port-security trap is enabled, new MAC addresses that violate the pre-defined port security configuration will trigger trap messages to be sent out. NOTIFICATION-TYPE .1.3.6.1.4.1.171.11.114.1.1.2.100.1.2.0.2 |
swl2NotificationBidings OBJECT IDENTIFIER .1.3.6.1.4.1.171.11.114.1.1.2.100.1.2.1 |
swL2macNotifyInfoThis object indicates the last time reboot information.ro OCTET STRING .1.3.6.1.4.1.171.11.114.1.1.2.100.1.2.1.1 |
swL2PortSecurityViolationMacThis object indicates the MAC address that violates the port security configuration.ro MacAddress (SNMPv2-TC) .1.3.6.1.4.1.171.11.114.1.1.2.100.1.2.1.2 |