DES3550-L2MGMT-MIB
The Structure of Layer 2 Network Management Information for the proprietary enterprise.
Main OID:
swL2MgmtMIB.1.3.6.1.4.1.171.11.64.2.2
295
Objects
Active
Status
5
Dependencies
Imported Objects
Objects
295 total| Object Name |
|---|
swL2MgmtMIBThe Structure of Layer 2 Network Management Information for the
proprietary enterprise. MODULE-IDENTITY .1.3.6.1.4.1.171.11.64.2.2 |
swL2DevMgmt OBJECT IDENTIFIER .1.3.6.1.4.1.171.11.64.2.2.1 |
swL2DevInfo OBJECT IDENTIFIER .1.3.6.1.4.1.171.11.64.2.2.1.1 |
swDevInfoSystemUpTimeThe value of sysUpTime at the time the switch entered its
current operational state. If the current state was entered
prior to the last re-initialization, then this object contains
a zero value. This value is in the units of seconds.ro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.171.11.64.2.2.1.1.1 |
swDevInfoTotalNumOfPortThe number of ports within this switch. This value is the sum
of the ports within this switch.ro INTEGER .1.3.6.1.4.1.171.11.64.2.2.1.1.2 |
swDevInfoNumOfPortInUseThe number of ports in this switch connected to the segment or
the end stations.ro INTEGER .1.3.6.1.4.1.171.11.64.2.2.1.1.3 |
swDevInfoConsoleInUseThe usage indication of the console system.ro Enumeration .1.3.6.1.4.1.171.11.64.2.2.1.1.4 |
swDevInfoModuleTypeThis object indicates the module type of this port.ro OCTET STRING .1.3.6.1.4.1.171.11.64.2.2.1.1.5 |
swDevInfoPowerTableA list of the temperature. SEQUENCE OF SwDevInfoPowerEntry .1.3.6.1.4.1.171.11.64.2.2.1.1.8 |
swDevInfoPowerEntryAn entry for Power information. SwDevInfoPowerEntry .1.3.6.1.4.1.171.11.64.2.2.1.1.8.1 |
swDevInfoPowerUnitIndexIndicates the ID of the unit in the Systemro INTEGER .1.3.6.1.4.1.171.11.64.2.2.1.1.8.1.1 |
swDevInfoPowerIDIndicates ID of the powerro INTEGER .1.3.6.1.4.1.171.11.64.2.2.1.1.8.1.2 |
swDevInfoPowerStatusIndicates status of the powerro Enumeration .1.3.6.1.4.1.171.11.64.2.2.1.1.8.1.3 |
swL2DevCtrl OBJECT IDENTIFIER .1.3.6.1.4.1.171.11.64.2.2.1.2 |
swL2DevCtrlStpStateThis object can enable or disable the spanning tree algorithm
during the runtime of the system.rw Enumeration .1.3.6.1.4.1.171.11.64.2.2.1.2.1 |
swL2DevCtrlIGMPSnoopingThis object indicates if the layer 2 Internet Group Management
Protocol (IGMP) capture function has been enabled or disabled.rw Enumeration .1.3.6.1.4.1.171.11.64.2.2.1.2.2 |
swL2DevCtrlRmonStateThis object can be enable or disable RMON.rw Enumeration .1.3.6.1.4.1.171.11.64.2.2.1.2.3 |
swL2DevCtrlCleanAllStatisticCounterIf the object is set to active, all the statistic counters will
be cleared. If set to normal, do nothing.rw Enumeration .1.3.6.1.4.1.171.11.64.2.2.1.2.8 |
swL2DevCtrlVlanIdOfFDBTblIndicates the VLAN ID which the Dot1dTpFdbTable belongs to ;
The default value is the DEFAULT_VLAN_ID of the system.rw VlanId .1.3.6.1.4.1.171.11.64.2.2.1.2.9 |
swL2MACNotifyStateThis object can enable or disable MAC Notification.rw Enumeration .1.3.6.1.4.1.171.11.64.2.2.1.2.10 |
swL2MACNotifyHistorySizeThis object indicates the history size of variation MAC in the address table.
The default value is 1 .rw INTEGER .1.3.6.1.4.1.171.11.64.2.2.1.2.11 |
swL2MACNotifyIntervalThis object indicates the time interval in seconds for triggering the MAC notify message.rw INTEGER .1.3.6.1.4.1.171.11.64.2.2.1.2.12 |
swL2DevCtrlAsymVlanStateThis object can enable or disable asymmetric VLANs
during the runtime of the system.rw Enumeration .1.3.6.1.4.1.171.11.64.2.2.1.2.13 |
swL2DevCtrlManagementVlanIdThis object controls which Vlan includes system ip
and that the Vlan should have been created.rw VlanId .1.3.6.1.4.1.171.11.64.2.2.1.2.14 |
swL2DevCtrlTelnet OBJECT IDENTIFIER .1.3.6.1.4.1.171.11.64.2.2.1.2.15 |
swL2DevCtrlTelnetStateThis object controls the Telnet status.rw Enumeration .1.3.6.1.4.1.171.11.64.2.2.1.2.15.1 |
swL2DevCtrlTelnetTcpPortThis object can designate a TCP port.
When Telnet is disabled this object isn't accessible.rw INTEGER .1.3.6.1.4.1.171.11.64.2.2.1.2.15.2 |
swL2DevCtrlLLDPStateSpecifies the state of the LLDP function.
When this function is enabled, the switch can start to transmit
LLDP packets and receive and process the LLDP packets.
The specific function of each port will depend on the per port
LLDP setting.
For the advertisement of LLDP packets, the switch announces the
information to its neighbor through ports. For the receiving of
LLDP packets, the switch will learn the information from the LLDP
packets advertised from the neighbor in the neighbor table.rw Enumeration .1.3.6.1.4.1.171.11.64.2.2.1.2.16 |
swL2DevCtrlWeb OBJECT IDENTIFIER .1.3.6.1.4.1.171.11.64.2.2.1.2.17 |
swL2DevCtrlWebStateThis object controls Web status.rw Enumeration .1.3.6.1.4.1.171.11.64.2.2.1.2.17.1 |
swL2DevCtrlWebTcpPortThis object can designate a TCP port.
When Web is disabled this object isn't accessible.rw INTEGER .1.3.6.1.4.1.171.11.64.2.2.1.2.17.2 |
swL2DevCtrlLLDPForwardMessageStateWhen lldp is disabled and lldp forward_message is enabled, the
received LLDP Data Unit packets will be forwarded.rw Enumeration .1.3.6.1.4.1.171.11.64.2.2.1.2.18 |
swL2DevAlarm OBJECT IDENTIFIER .1.3.6.1.4.1.171.11.64.2.2.1.3 |
swL2DevAlarmNewRootWhen the device has become the new root of Spanning Tree,
this object decides whether to send a new root trap.rw Enumeration .1.3.6.1.4.1.171.11.64.2.2.1.3.1 |
swL2DevAlarmTopologyChangeThis object determines whether to send a trap or not when the switch
topology has changed. If the object is enabled(3),
the topology change trap is sent by the device when any of its
configured ports transition from the Learning state to the
Forwarding state, or from the Forwarding state to the Blocking
state. For the same port transition, the device doesn't send the
trap if this object value is set to disabled or other.rw Enumeration .1.3.6.1.4.1.171.11.64.2.2.1.3.2 |
swL2DevAlarmLinkChangeThis object determines whether to send a trap or not when the link
has changed. If the object is enabled (3), the Link Change
trap is sent by the device when any of its port links change.
The device doesn't send the trap if this object value is set to
disabled or other.rw Enumeration .1.3.6.1.4.1.171.11.64.2.2.1.3.3 |
swL2VlanMgmt OBJECT IDENTIFIER .1.3.6.1.4.1.171.11.64.2.2.3 |
swL2VlanAdvertisementTableA table containing the advertisement state for each
VLAN configured into the device by (local or
network) management. SEQUENCE OF SwL2VlanAdvertisementEntry .1.3.6.1.4.1.171.11.64.2.2.3.1 |
swL2VlanAdvertisementEntryAdvertisement state for each VLAN configured
in the device. SwL2VlanAdvertisementEntry .1.3.6.1.4.1.171.11.64.2.2.3.1.1 |
swL2VlanIndexThe VLAN-ID or other identifier referring to this VLAN.ro INTEGER .1.3.6.1.4.1.171.11.64.2.2.3.1.1.1 |
swL2VlanNameAn administratively assigned string, which may be used
to identify the VLAN.ro DisplayString .1.3.6.1.4.1.171.11.64.2.2.3.1.1.2 |
swL2VlanAdvertiseStateThis object indicates the advertised status of this VLAN entry.rw Enumeration .1.3.6.1.4.1.171.11.64.2.2.3.1.1.3 |
swL2PortMgmt OBJECT IDENTIFIER .1.3.6.1.4.1.171.11.64.2.2.4 |
swL2PortInfoTableA table that contains information about every port.obsolete SEQUENCE OF SwL2PortInfoEntry .1.3.6.1.4.1.171.11.64.2.2.4.1 |
swL2PortInfoEntryA list of information for each port of the device.obsolete SwL2PortInfoEntry .1.3.6.1.4.1.171.11.64.2.2.4.1.1 |
swL2PortInfoPortIndexThis object indicates the module's port number.(1..Max port
number in the module).roobsolete INTEGER .1.3.6.1.4.1.171.11.64.2.2.4.1.1.1 |
swL2PortInfoUnitIndexIndicates ID of the unit in the deviceroobsolete INTEGER .1.3.6.1.4.1.171.11.64.2.2.4.1.1.2 |
swL2PortInfoTypeThis object indicates the connector type of this port.roobsolete Enumeration .1.3.6.1.4.1.171.11.64.2.2.4.1.1.3 |
swL2PortInfoLinkStatusThis object indicates the port link status.roobsolete Enumeration .1.3.6.1.4.1.171.11.64.2.2.4.1.1.4 |
swL2PortInfoNwayStatusThis object indicates the port speed and duplex mode.roobsolete Enumeration .1.3.6.1.4.1.171.11.64.2.2.4.1.1.5 |
swL2PortInfoModuleTypeThis object indicates the module type of this port.roobsolete Enumeration .1.3.6.1.4.1.171.11.64.2.2.4.1.1.6 |
swL2PortInfoErrorDisabledThis object indicates the blocking type of this port.roobsolete Enumeration .1.3.6.1.4.1.171.11.64.2.2.4.1.1.7 |
swL2PortCtrlTableA table that contains control information about every port.obsolete SEQUENCE OF SwL2PortCtrlEntry .1.3.6.1.4.1.171.11.64.2.2.4.2 |
swL2PortCtrlEntryA list of control information for each port of the device.obsolete SwL2PortCtrlEntry .1.3.6.1.4.1.171.11.64.2.2.4.2.1 |
swL2PortCtrlPortIndexThis object indicates the module's port number.(1..Max port
number in the module)roobsolete INTEGER .1.3.6.1.4.1.171.11.64.2.2.4.2.1.1 |
swL2PortCtrlUnitIndexIndicates the ID of the unit in the deviceroobsolete INTEGER .1.3.6.1.4.1.171.11.64.2.2.4.2.1.2 |
swL2PortCtrlAdminStateThis object decides whether the port is enabled or disabled.rwobsolete Enumeration .1.3.6.1.4.1.171.11.64.2.2.4.2.1.3 |
swL2PortCtrlNwayStateChoose the port speed, duplex mode, and N-Way function mode.rwobsolete Enumeration .1.3.6.1.4.1.171.11.64.2.2.4.2.1.4 |
swL2PortCtrlFlowCtrlStateThe flow control mechanism is different between full duplex
mode and half duplex mode. For half duplex mode, the jamming
signal is asserted. For full duplex mode, IEEE 802.3x flow
control function sends PAUSE frames and receives PAUSE frames.rwobsolete Enumeration .1.3.6.1.4.1.171.11.64.2.2.4.2.1.5 |
swL2PortCtrlLockStateThis object decides whether the port is locked or not.rwobsolete Enumeration .1.3.6.1.4.1.171.11.64.2.2.4.2.1.6 |
swL2PortCtrlMACNotifyStateThis object decides whether MAC notification is enabled or not.rwobsolete Enumeration .1.3.6.1.4.1.171.11.64.2.2.4.2.1.7 |
swL2PortCtrlMulticastfilterThis object decides the multicast packet filtering mode on this port .rwobsolete Enumeration .1.3.6.1.4.1.171.11.64.2.2.4.2.1.8 |
swL2PortCtrlMdixStateThis object decides the MDIX mode on this port.rwobsolete Enumeration .1.3.6.1.4.1.171.11.64.2.2.4.2.1.11 |
swL2PortInformationTableA table that contains information about every port. SEQUENCE OF SwL2PortInformationEntry .1.3.6.1.4.1.171.11.64.2.2.4.4 |
swL2PortInformationEntryA list of information for each port of the device. SwL2PortInformationEntry .1.3.6.1.4.1.171.11.64.2.2.4.4.1 |
swL2PortInformationPortIndexThis object indicates the module's port number.(1..Max port
number in the module)ro INTEGER .1.3.6.1.4.1.171.11.64.2.2.4.4.1.1 |
swL2PortInformationMediumTypeIndicates medium type of the port number.ro Enumeration .1.3.6.1.4.1.171.11.64.2.2.4.4.1.2 |
swL2PortInformationUnitIDIndicates ID of the unit in the systemro INTEGER .1.3.6.1.4.1.171.11.64.2.2.4.4.1.3 |
swL2PortInformationTypeThis object indicates the connector type of this port.ro Enumeration .1.3.6.1.4.1.171.11.64.2.2.4.4.1.4 |
swL2PortInformationLinkStatusThis object indicates the port link status.ro Enumeration .1.3.6.1.4.1.171.11.64.2.2.4.4.1.5 |
swL2PortInformationNwayStatusThis object indicates the port speed and duplex mode.ro Enumeration .1.3.6.1.4.1.171.11.64.2.2.4.4.1.6 |
swL2PortInformationModuleTypeThis object indicates the module type of this port.ro Enumeration .1.3.6.1.4.1.171.11.64.2.2.4.4.1.7 |
swL2PortInformationErrorDisabledThis object indicates the blocking type of this port.ro Enumeration .1.3.6.1.4.1.171.11.64.2.2.4.4.1.8 |
swL2PortControlTableA table that contains control information about every port. SEQUENCE OF SwL2PortControlEntry .1.3.6.1.4.1.171.11.64.2.2.4.5 |
swL2PortControlEntryA list of control information for each port of the device. SwL2PortControlEntry .1.3.6.1.4.1.171.11.64.2.2.4.5.1 |
swL2PortControlPortIndexThis object indicates the module's port number.(1..Max port
number in the module)ro INTEGER .1.3.6.1.4.1.171.11.64.2.2.4.5.1.1 |
swL2PortControlMediumTypeIndicates the medium type of the port number.ro Enumeration .1.3.6.1.4.1.171.11.64.2.2.4.5.1.2 |
swL2PortControlUnitIndexIndicates ID of the unit in the devicero INTEGER .1.3.6.1.4.1.171.11.64.2.2.4.5.1.3 |
swL2PortControlAdminStateThis object decides if the port is enabled or disabled.rw Enumeration .1.3.6.1.4.1.171.11.64.2.2.4.5.1.4 |
swL2PortControlNwayStateChoose the port speed, duplex mode, and N-Way function mode.rw Enumeration .1.3.6.1.4.1.171.11.64.2.2.4.5.1.5 |
swL2PortControlFlowCtrlStateThe flow control mechanism is different between full duplex
mode and half duplex mode. For half duplex mode, the jamming
signal is asserted. For full duplex mode, the IEEE 802.3x flow
control function sends PAUSE frames and receives PAUSE frames.rw Enumeration .1.3.6.1.4.1.171.11.64.2.2.4.5.1.6 |
swL2PortControlLockStateThis object decides whether the port is locked or not.rwobsolete Enumeration .1.3.6.1.4.1.171.11.64.2.2.4.5.1.7 |
swL2PortControlMACNotifyStateThis object sets each port's MAC notification state.rw Enumeration .1.3.6.1.4.1.171.11.64.2.2.4.5.1.8 |
swL2PortControlMulticastfilterThis object controls the multicast port filtering mode for a specified port.rw Enumeration .1.3.6.1.4.1.171.11.64.2.2.4.5.1.9 |
swL2PortControlMdixStateThis object decides the MDIX mode on this port.rw Enumeration .1.3.6.1.4.1.171.11.64.2.2.4.5.1.11 |
swL2LimitedMulticastMgmt OBJECT IDENTIFIER .1.3.6.1.4.1.171.11.64.2.2.5 |
swL2MulticastRangeTable. SEQUENCE OF SwL2MulticastRangeEntry .1.3.6.1.4.1.171.11.64.2.2.5.1 |
swL2MulticastRangeEntryA list of information contained in swL2MulticastRangeTable. SwL2MulticastRangeEntry .1.3.6.1.4.1.171.11.64.2.2.5.1.1 |
swL2MulticastRangeNameThis object specifies the multicast range name.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.171.11.64.2.2.5.1.1.1 |
swL2MulticastRangeFromIpThis object specifies the start IP address for this range.rw IpAddress .1.3.6.1.4.1.171.11.64.2.2.5.1.1.2 |
swL2MulticastRangeToIpThis object specifies the end IP address for this range.rw IpAddress .1.3.6.1.4.1.171.11.64.2.2.5.1.1.3 |
swL2MulticastRangeRowStatusThis object indicates the status of this entry.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.171.11.64.2.2.5.1.1.4 |
swL2LimitedMulticastPortInfo OBJECT IDENTIFIER .1.3.6.1.4.1.171.11.64.2.2.5.2 |
swL2LimitedMulticastStatusTable. SEQUENCE OF SwL2LimitedMulticastStatusEntry .1.3.6.1.4.1.171.11.64.2.2.5.2.1 |
swL2LimitedMulticastStatusEntryA list of information contained in swL2LimitedMulticastStatusTable. SwL2LimitedMulticastStatusEntry .1.3.6.1.4.1.171.11.64.2.2.5.2.1.1 |
swL2LimitedMulticastPortThis object indicates the port.ro INTEGER .1.3.6.1.4.1.171.11.64.2.2.5.2.1.1.1 |
swL2LimitedMulticastAccessThis object indicates the access type.rw Enumeration .1.3.6.1.4.1.171.11.64.2.2.5.2.1.1.2 |
swL2LimitedMulticastStateThis object indicates the state for this port.rw Enumeration .1.3.6.1.4.1.171.11.64.2.2.5.2.1.1.3 |
swL2LimitedMulticastRangeTable. SEQUENCE OF SwL2LimitedMulticastRangeEntry .1.3.6.1.4.1.171.11.64.2.2.5.2.2 |
swL2LimitedMulticastRangeEntryA list of information contained in swL2LimitedMulticastRangeTable. SwL2LimitedMulticastRangeEntry .1.3.6.1.4.1.171.11.64.2.2.5.2.2.1 |
swL2LimitedMulticastIDThis object indicates the range ID.ro INTEGER .1.3.6.1.4.1.171.11.64.2.2.5.2.2.1.1 |
swL2LimitedMulticastRangeNamerw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.171.11.64.2.2.5.2.2.1.2 |
swL2LimitedMulticastFromIpThis object specifies the start IP address of the
range on this port.ro IpAddress .1.3.6.1.4.1.171.11.64.2.2.5.2.2.1.3 |
swL2LimitedMulticastToIpThis object specifies the end IP address of the
range on this port.ro IpAddress .1.3.6.1.4.1.171.11.64.2.2.5.2.2.1.4 |
swL2LimitedMulticastRowStatusThis object indicates the status of this entry.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.171.11.64.2.2.5.2.2.1.5 |
swL2QOSMgmt OBJECT IDENTIFIER .1.3.6.1.4.1.171.11.64.2.2.6 |
swL2QOSBandwidthControlTable. SEQUENCE OF SwL2QOSBandwidthControlEntry .1.3.6.1.4.1.171.11.64.2.2.6.1 |
swL2QOSBandwidthControlEntryA list of information contained in swL2QOSBandwidthControlTable. SwL2QOSBandwidthControlEntry .1.3.6.1.4.1.171.11.64.2.2.6.1.1 |
swL2QOSBandwidthPortIndexIndicates the port.ro INTEGER .1.3.6.1.4.1.171.11.64.2.2.6.1.1.1 |
swL2QOSBandwidthRxRateIndicates the RX Rate(Mbit/sec) of the specifed port. Value 0 means no limit.rw INTEGER .1.3.6.1.4.1.171.11.64.2.2.6.1.1.2 |
swL2QOSBandwidthTxRateIndicates the TX Rate(Mbit/sec) of the specifed port. Value 0 means no limit.rw INTEGER .1.3.6.1.4.1.171.11.64.2.2.6.1.1.3 |
swL2QOSBandwidthRadiusRxRateThe Rx Rate value comes from the RADIUS server,
If an 802.1X port is authenticated, this value
will overwrite the locally configured Rx Rate.ro INTEGER .1.3.6.1.4.1.171.11.64.2.2.6.1.1.4 |
swL2QOSBandwidthRadiusTxRateThe Tx Rate value comes from the RADIUS server,
If an 802.1X port is authenticated, this value
will overwrite the locally configured Tx Rate.ro INTEGER .1.3.6.1.4.1.171.11.64.2.2.6.1.1.5 |
swL2QOSSchedulingTable. SEQUENCE OF SwL2QOSSchedulingEntry .1.3.6.1.4.1.171.11.64.2.2.6.2 |
swL2QOSSchedulingEntryA list of information contained in swL2QOSSchedulingTable. SwL2QOSSchedulingEntry .1.3.6.1.4.1.171.11.64.2.2.6.2.1 |
swL2QOSSchedulingClassIndexIndicates the hardware queue number.ro INTEGER .1.3.6.1.4.1.171.11.64.2.2.6.2.1.1 |
swL2QOSSchedulingMaxPktsIndicates the maximum number of packets the hardware priority queue will be allowed
to transmit before allowing the next lowest priority queue to transmit its packets.
a value between 0 and 255 can be specified.rw INTEGER .1.3.6.1.4.1.171.11.64.2.2.6.2.1.2 |
swL2QOSSchedulingMaxLatencyIndicates the maximum amount of time the hardware priority queue will be allowed
to transmit packets before allowing the next lowest priority queue to begin transmitting
its packets. A value between 0 and 255 can be specified- with this value multiplied
by 16 ms to arrive at the total allowed time for queue to transmit packets.
For example, a value of 3 specifies 3*16=48 ms. The queue will continue transmitting
the last packet until it is finished when the max_latency timer expires.rw INTEGER .1.3.6.1.4.1.171.11.64.2.2.6.2.1.3 |
swL2QOS8021pUserPriorityTable. SEQUENCE OF SwL2QOS8021pUserPriorityEntry .1.3.6.1.4.1.171.11.64.2.2.6.3 |
swL2QOS8021pUserPriorityEntryA list of information contained in swL2QOS8021pUserPriorityTable. SwL2QOS8021pUserPriorityEntry .1.3.6.1.4.1.171.11.64.2.2.6.3.1 |
swL2QOS8021pUserPriorityIndexThe 802.1p user priority .ro INTEGER .1.3.6.1.4.1.171.11.64.2.2.6.3.1.1 |
swL2QOS8021pUserPriorityClassThe number of the switch's hardware priority queue. The switch has four hardware
priority queues available. They are numbered between 0 (the lowest priority)
and 3 (the highest priority).rw INTEGER .1.3.6.1.4.1.171.11.64.2.2.6.3.1.2 |
swL2QOS8021pDefaultPriorityTable. SEQUENCE OF SwL2QOS8021pDefaultPriorityEntry .1.3.6.1.4.1.171.11.64.2.2.6.4 |
swL2QOS8021pDefaultPriorityEntryA list of information contained in swL2QOS8021pDefaultPriorityTable. SwL2QOS8021pDefaultPriorityEntry .1.3.6.1.4.1.171.11.64.2.2.6.4.1 |
swL2QOS8021pDefaultPriorityIndexIndicates the port number.ro INTEGER .1.3.6.1.4.1.171.11.64.2.2.6.4.1.1 |
swL2QOS8021pDefaultPriorityThe priority value to assign to untagged packets received by the
switch ports on the switch.rw INTEGER .1.3.6.1.4.1.171.11.64.2.2.6.4.1.2 |
swL2QOS8021pRadiusPriorityIndicates the value of 802.1p comes from RADIUS server.
If an 802.1X port is authenticated,
this value will overwrite the local configured value.ro INTEGER .1.3.6.1.4.1.171.11.64.2.2.6.4.1.3 |
swL2IpMacBindingMgmt OBJECT IDENTIFIER .1.3.6.1.4.1.171.11.64.2.2.7 |
swL2IpMacBindingPortTableThe table specifies the port's ip-mac binding function. SEQUENCE OF SwL2IpMacBindingPortEntry .1.3.6.1.4.1.171.11.64.2.2.7.1 |
swL2IpMacBindingPortEntryA list of information about the port's ip-mac binding function. SwL2IpMacBindingPortEntry .1.3.6.1.4.1.171.11.64.2.2.7.1.1 |
swL2IpMacBindingPortIndexThis object indicates the module's port number.(1..Max port
number in the module).ro INTEGER .1.3.6.1.4.1.171.11.64.2.2.7.1.1.1 |
swL2IpMacBindingPortStateThis object enables (strict or loose mode)/disables IP-MAC binding
on the specified port.
Note:
enable-strict (2): SW learning
enable-loose (4) : HW learningrw Enumeration .1.3.6.1.4.1.171.11.64.2.2.7.1.1.2 |
swL2IpMacBindingPortAllowZeroIpThis object enables/disables the allow zero IP status on the specified port.rw Enumeration .1.3.6.1.4.1.171.11.64.2.2.7.1.1.3 |
swL2IpMacBindingPortForwardDhcpPktThis object can be set to forward or not forward DHCP packets on the specified port.rw Enumeration .1.3.6.1.4.1.171.11.64.2.2.7.1.1.4 |
swL2IpMacBindingPortDHCPSnoopMaxEntryThis object indicates the max entry created by DHCP packets on the
specified port.
Note:
When 0 is set on the specified port, the max entry created by DHCP packets
is no limitrw INTEGER .1.3.6.1.4.1.171.11.64.2.2.7.1.1.5 |
swL2IpMacBindingPortDHCPSnoopEntryClearActionWhen set to start(2), the address binding entries learned
for the specified ports will be cleared.
When get, it always returns other (1).rw Enumeration .1.3.6.1.4.1.171.11.64.2.2.7.1.1.6 |
swL2IpMacBindingTableThis table specifies IP-MAC binding information. SEQUENCE OF SwL2IpMacBindingEntry .1.3.6.1.4.1.171.11.64.2.2.7.2 |
swL2IpMacBindingEntryIP-MAC binding entry used to add\delete\configure the address
pair to the switch's authorized user database. SwL2IpMacBindingEntry .1.3.6.1.4.1.171.11.64.2.2.7.2.1 |
swL2IpMacBindingIpIndexThe IP address of the IP-MAC binding.ro IpAddress .1.3.6.1.4.1.171.11.64.2.2.7.2.1.1 |
swL2IpMacBindingMacThe MAC address of the IP-MAC binding.rw MacAddress (SNMPv2-TC) .1.3.6.1.4.1.171.11.64.2.2.7.2.1.2 |
swL2IpMacBindingStatusThe status of this entry.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.171.11.64.2.2.7.2.1.3 |
swL2IpMacBindingPortsThe port members of this entry.rw PortList .1.3.6.1.4.1.171.11.64.2.2.7.2.1.4 |
swL2IpMacBindingActionThe action of this entry.ro Enumeration .1.3.6.1.4.1.171.11.64.2.2.7.2.1.5 |
swL2IpMacBindingModeThe mode of this entry.
arp: This entry is specified as an ARP mode entry, and this
entry will not be added as an access entry. If this
object is not specified, the mode defaults to ARP mode.
If the system is in ARP mode, the ARP mode entries and
ACL mode entries will be effective. If the system is in
ACL mode, only the ACL mode entries will be active.
acl: This entry is specified as an ACL mode entry. If the
user enables the ACL mode, this entry will be added as
an access entry.
auto: This mode cannot be configured, and when the auto mode
is employed, it means this entry is to be learned by DHCP
snooping.rw Enumeration .1.3.6.1.4.1.171.11.64.2.2.7.2.1.6 |
swL2IpMacBindingBlockedTableThe table specifies information of MAC addresses which were blocked. SEQUENCE OF SwL2IpMacBindingBlockedEntry .1.3.6.1.4.1.171.11.64.2.2.7.3 |
swL2IpMacBindingBlockedEntryThe entry can not create/configure. It can only delete. SwL2IpMacBindingBlockedEntry .1.3.6.1.4.1.171.11.64.2.2.7.3.1 |
swL2IpMacBindingBlockedVIDThe object specifies the VLAN ID.ro VlanIndex .1.3.6.1.4.1.171.11.64.2.2.7.3.1.1 |
swL2IpMacBindingBlockedMacThe MAC address which was blocked.ro MacAddress (SNMPv2-TC) .1.3.6.1.4.1.171.11.64.2.2.7.3.1.2 |
swL2IpMacBindingBlockedVlanNameThis object specifies the VLAN name.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.171.11.64.2.2.7.3.1.3 |
swL2IpMacBindingBlockedPortThe port with which the MAC is associated.ro INTEGER .1.3.6.1.4.1.171.11.64.2.2.7.3.1.4 |
swL2IpMacBindingBlockedTypeThe value is always blockByAddrBind. This entry will be deleted by setting the value to delete(3).rw Enumeration .1.3.6.1.4.1.171.11.64.2.2.7.3.1.5 |
swL2IpMacBindingAllPortStateThis object enables/disables IP-MAC binding on all ports of the system.
This action is only applicable when users have write privileges,
and can only be viewed when users have read privileges.
Note:
enable-strict (2): This means strict mode (SW learning). All packets are sent
to the CPU. If the user chooses, the port will check ARP packets
and IP packets by IP-MAC-PORT Binding entries. If the MAC
address can be found or not found by the entry, the MAC will
be set as dynamic learned or it will set as blocked, respectively. Other
packets will be sent to the CPU and dropped.
enable-loose (4) : This means loose mode (HW learning): Only ARP packets and IP
broadcast packets will be sent to the CPU. If the user chooses ,
the port will learn the MAC address on non-ARP and non-IP
broadcast packets directly, so these packets will be bypassed.
But if the switch receives the ARP or IP broadcast packets and
Can not bypass the IP MAC Binding checking, the switch will set
this MAC address as blocked and all packets from this MAC
address will be dropped.rw Enumeration .1.3.6.1.4.1.171.11.64.2.2.7.4 |
swL2IpMacBindingTrapLogStatewhen set to enable(2),whenever there's a new MAC that violates the pre-defined
Ip Mac Binding configuration, the trap will be sent out and the relevant information
will be logged into the system.rw Enumeration .1.3.6.1.4.1.171.11.64.2.2.7.5 |
swL2IpMacBindingACLModewhen set to enable(2), the Ip Mac Binding will use acl moderw Enumeration .1.3.6.1.4.1.171.11.64.2.2.7.6 |
swL2IpMacBindingDHCPSnoopStateWhen the dhcp_snoop function is enabled, all address_binding
disabled ports will act as DHCP server ports (the switch will
learn IP addresses through DHCP server ports (by DHCP OFFER
and DHCP ACK packets)).
The auto-learned IP-MAC binding entry will be mapped to a specific
source port based on the MAC address learning function. This entry
will be created as an ACL-mode binding entry for this specific port.
Each entry is associated with a lease time. When the lease time
expires, the expired entry will be removed from this port. The
automatically learned binding entry can be moved from one port to
another port if the DHCP snooping function has learned that the MAC
address has moved to a different port.
Consider a case where DHCP snooping learns a binding entry, and the
same IP-MAC binding entry has been statically configured. Suppose
that the learned information is consistent with the statically
configured entry, then the automatically learned entry will not be
created. Suppose the entry is statically configured in ARP
mode, since the automatically learned entry will be created in ACL
mode, the entry will become ACL mode. Suppose the entry is
statically configured on one port and the entry is automatically
learned on another port, then both entries will exist.
When the dhcp_snoop function is disabled, all of the automatically
learned binding entries will be removed.rw Enumeration .1.3.6.1.4.1.171.11.64.2.2.7.7 |
swL2IpMacBindingDHCPSnoopEntryClearAllStateUsed to clear all entries created by DHCP packets.rw Enumeration .1.3.6.1.4.1.171.11.64.2.2.7.8 |
swL2IpMacBindingDHCPSnoopTableThe table specifies information regarding the DHCP snooping
function learning IP-MAC binding entries. SEQUENCE OF SwL2IpMacBindingDHCPSnoopEntry .1.3.6.1.4.1.171.11.64.2.2.7.9 |
swL2IpMacBindingDHCPSnoopEntryA list of information about the DHCP snooping learning
IP-MAC binding entry. SwL2IpMacBindingDHCPSnoopEntry .1.3.6.1.4.1.171.11.64.2.2.7.9.1 |
swL2IpMacBindingDHCPSnoopIpIndexThe IP address of this entry.ro IpAddress .1.3.6.1.4.1.171.11.64.2.2.7.9.1.1 |
swL2IpMacBindingDHCPSnoopMacThe MAC address of this entry.ro MacAddress (SNMPv2-TC) .1.3.6.1.4.1.171.11.64.2.2.7.9.1.2 |
swL2IpMacBindingDHCPSnoopLeaseTimeSpecifies the lease time of this entry.
When the lease time expires, this entry will be removed from
this port.ro INTEGER .1.3.6.1.4.1.171.11.64.2.2.7.9.1.3 |
swL2IpMacBindingDHCPSnoopPortSpecifies the port of this entry.ro INTEGER .1.3.6.1.4.1.171.11.64.2.2.7.9.1.4 |
swL2IpMacBindingDHCPSnoopStatusSpecifies the status (inactive or active) of this entry.ro Enumeration .1.3.6.1.4.1.171.11.64.2.2.7.9.1.5 |
swL2IpMacBindingPermitIPPoolTableThis table specifies the permitted IP pool of IP-MAC binding. SEQUENCE OF SwL2IpMacBindingPermitIPPoolEntry .1.3.6.1.4.1.171.11.64.2.2.7.10 |
swL2IpMacBindingPermitIPPoolEntryA list of information of each permitted IP pool entry. SwL2IpMacBindingPermitIPPoolEntry .1.3.6.1.4.1.171.11.64.2.2.7.10.1 |
swL2IpMacBindingPermitIPPoolStartIPThe start IP address of the permitted IP pool.ro IpAddress .1.3.6.1.4.1.171.11.64.2.2.7.10.1.1 |
swL2IpMacBindingPermitIPPoolEndIPThe end IP address of the permitted IP pool.ro IpAddress .1.3.6.1.4.1.171.11.64.2.2.7.10.1.2 |
swL2IpMacBindingPermitIPPoolPortsThe port members of the permitted IP pool.rw PortList .1.3.6.1.4.1.171.11.64.2.2.7.10.1.3 |
swL2IpMacBindingPermitIPPoolStatusThe status of the permitted IP pool.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.171.11.64.2.2.7.10.1.4 |
swL2TrunkMgmt OBJECT IDENTIFIER .1.3.6.1.4.1.171.11.64.2.2.8 |
swL2TrunkMaxSupportedEntriesMaximum number of entries in the trunk configuration table
(swL2TrunkCtrlTable).ro INTEGER .1.3.6.1.4.1.171.11.64.2.2.8.1 |
swL2TrunkCurrentNumEntriesCurrent active number of entries in the trunk configuration
table.ro INTEGER .1.3.6.1.4.1.171.11.64.2.2.8.2 |
swL2TrunkCtrlTableThis table specifies which ports are grouped as a set of ports(up to 8)
into a single logical link. SEQUENCE OF SwL2TrunkCtrlEntry .1.3.6.1.4.1.171.11.64.2.2.8.3 |
swL2TrunkCtrlEntryA list of information specifies which ports are grouped as a set of
ports(up to 8) into a single logical link. SwL2TrunkCtrlEntry .1.3.6.1.4.1.171.11.64.2.2.8.3.1 |
swL2TrunkIndexThe index of logical port trunk. The trunk group number depends
on the existence of the unit and module.ro INTEGER .1.3.6.1.4.1.171.11.64.2.2.8.3.1.1 |
swL2TrunkNameThe name of logical port trunk.rw DisplayString .1.3.6.1.4.1.171.11.64.2.2.8.3.1.2 |
swL2TrunkMasterPortThe object indicates the master port number of the port trunk
entry. When using Port Trunk, you can not configure the other
ports of the group except the master port.
Their configuration must be the same as the master port (e.g. speed,
duplex, enabled/disabled, flow control, and so on).rw INTEGER .1.3.6.1.4.1.171.11.64.2.2.8.3.1.3 |
swL2TrunkMemberIndicates how many ports are included in this Trunk.
The trunk port number depends on the existence of module.
The maximum number of ports is 8 for one trunks.rw PortList .1.3.6.1.4.1.171.11.64.2.2.8.3.1.4 |
swL2TrunkFloodingPortThe object indicates the flooding port number of the port trunk
entry. The first port of the trunk is implicitly configured to
be the flooding port.ro INTEGER .1.3.6.1.4.1.171.11.64.2.2.8.3.1.5 |
swL2TrunkTypeThis object indicates the type of the trunk group.
static : is static trunk group
lacp : is LACP trunk group .rw Enumeration .1.3.6.1.4.1.171.11.64.2.2.8.3.1.6 |
swL2TrunkStateThis object indicates the status of this entry.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.171.11.64.2.2.8.3.1.7 |
swL2TrunkAlgorithmThis object configures the part of the packet examined by the
switch when selecting the egress port for transmitting
load-sharing data.rw Enumeration .1.3.6.1.4.1.171.11.64.2.2.8.4 |
swL2MirrorMgmt OBJECT IDENTIFIER .1.3.6.1.4.1.171.11.64.2.2.9 |
swL2MirrorLogicTargetPortThis object indicates which port will sniff another
port to the switch. A trunk port member cannot be configured as a target
Snooping port. The port number is the sequential (logical)
number which is also applied to bridge MIB, etc.rw INTEGER .1.3.6.1.4.1.171.11.64.2.2.9.1 |
swL2MirrorPortSourceIngressThis represents the ingress of the source port packet to be
sniffed.rw PortList .1.3.6.1.4.1.171.11.64.2.2.9.2 |
swL2MirrorPortSourceEgressThis represents the egress of the source port packet to be
sniffed.rw PortList .1.3.6.1.4.1.171.11.64.2.2.9.3 |
swL2MirrorPortStateThis object indicates the port mirroring state.
other(1) - this entry is currently in use but the conditions
under which it will remain so are different for each of the
following values.
disabled(2) - writing this value to the object will remove the
corresponding entry from the table.
enabled(3) - this entry will reside in the table.rw Enumeration .1.3.6.1.4.1.171.11.64.2.2.9.4 |
swL2IGMPMgmt OBJECT IDENTIFIER .1.3.6.1.4.1.171.11.64.2.2.10 |
swL2IGMPMaxSupportedVlansMaximum number of VLANs in the layer 2 IGMP control table
(swL2IGMPCtrlTable).ro INTEGER .1.3.6.1.4.1.171.11.64.2.2.10.1 |
swL2IGMPCtrlTableThis table controls the VLAN's IGMP function. Its scale depends
on the current VLAN state (swL2VlanInfoStatus). If VLAN is in disabled
mode, there is only one entry in the table, with index 1. If
VLAN is in Port-Base or 802.1q mode, the number of entries can
be up to 12, with an index range from 1 to 12. SEQUENCE OF SwL2IGMPCtrlEntry .1.3.6.1.4.1.171.11.64.2.2.10.3 |
swL2IGMPCtrlEntryThe entry in IGMP control table (swL2IGMPCtrlTable). The entry
is effective only when IGMP capture switch
(swL2DevCtrlIGMPSnooping) is enabled. SwL2IGMPCtrlEntry .1.3.6.1.4.1.171.11.64.2.2.10.3.1 |
swL2IGMPCtrlVidThis object indicates the IGMP control entry's VLAN ID. If VLAN
is disabled, the VID is always 0 and cannot be changed by
management users. If VLAN is in Port-Base mode, the VID is
arranged from 1 to 12, fixed form. If VLAN is in 802.1q mode,
the VID setting can vary from 1 to 4094 by management user, and
the Vid in each entry must be unique in the IGMP Control Table.ro INTEGER .1.3.6.1.4.1.171.11.64.2.2.10.3.1.1 |
swL2IGMPQueryIntervalThe frequency at which the IGMP Host-Query packets are
transmitted on this switch.rw INTEGER .1.3.6.1.4.1.171.11.64.2.2.10.3.1.2 |
swL2IGMPMaxResponseTimeThe maximum query response time on this switch.rw INTEGER .1.3.6.1.4.1.171.11.64.2.2.10.3.1.3 |
swL2IGMPRobustnessThe Robustness Variable allows tuning for the expected
packet loss on a subnet. If a subnet is expected to have a high
loss, the Robustness Variable may be increased. IGMP is
robust to (Robustness Variable-1) packet losses.rw INTEGER .1.3.6.1.4.1.171.11.64.2.2.10.3.1.4 |
swL2IGMPLastMemberQueryIntervalThe Last Member Query Interval is the Max Response Time
inserted into Group-Specific Queries sent in response to
Leave Group messages, and is also the amount of time between
Group-Specific Query messages.rw INTEGER .1.3.6.1.4.1.171.11.64.2.2.10.3.1.5 |
swL2IGMPHostTimeoutThe timer value for sending IGMP query packet when none was
sent by the host in the LAN. The timer works in per-VLAN basis.
Our device will be activated to send the query message if the
timer has expired. Please reference RFC2236-1997.rw INTEGER .1.3.6.1.4.1.171.11.64.2.2.10.3.1.6 |
swL2IGMPRouteTimeoutThe Router Timeout is how long a host must wait after hearing
a Query before it may send any IGMPv2 messages.rw INTEGER .1.3.6.1.4.1.171.11.64.2.2.10.3.1.7 |
swL2IGMPLeaveTimerWhen a query receives a Leave Group message for a group that
has group members on the reception interface, it sends
Group-Specific Queries every swL2IGMPLeaveTimer to the group
being left.rw INTEGER .1.3.6.1.4.1.171.11.64.2.2.10.3.1.8 |
swL2IGMPQueryStateThis object decides if the IGMP query is enabled or disabled.rw Enumeration .1.3.6.1.4.1.171.11.64.2.2.10.3.1.9 |
swL2IGMPCurrentStateThis object indicates the current IGMP query state.ro Enumeration .1.3.6.1.4.1.171.11.64.2.2.10.3.1.10 |
swL2IGMPCtrlStateThis object indicates the status of this entry.
other(1) - this entry is currently in use but the conditions under
which it will remain so are different for each of the following
values.
disable(2) - IGMP funtion is disabled for this entry.
enable(3) - IGMP funtion is enabled for this entry.rw Enumeration .1.3.6.1.4.1.171.11.64.2.2.10.3.1.11 |
swL2IGMPQueryInfoTableThe table contains the current number of IGMP query packets which
have been captured by this device, as well as the IGMP query packets
sent by the device. SEQUENCE OF SwL2IGMPQueryInfoEntry .1.3.6.1.4.1.171.11.64.2.2.10.4 |
swL2IGMPQueryInfoEntryInformation about current IGMP query information, provided that
swL2DevCtrlIGMPSnooping and swL2IGMPCtrState of associated VLAN
entires are all enabled. SwL2IGMPQueryInfoEntry .1.3.6.1.4.1.171.11.64.2.2.10.4.1 |
swL2IGMPInfoVidThis object indicates the VID of the associated IGMP info table
entry. It follows swL2IGMPCtrlVid in the associated entry of the
IGMP control table (swL2IGMPCtrlTable).ro INTEGER .1.3.6.1.4.1.171.11.64.2.2.10.4.1.1 |
swL2IGMPInfoQueryCountThis object indicates the number of query packets received
since the IGMP function has been enabled, on a per-VLAN basis.ro INTEGER .1.3.6.1.4.1.171.11.64.2.2.10.4.1.2 |
swL2IGMPInfoTxQueryCountThis object indicates the send count of IGMP query messages, on a
per-VLAN basis. In case of the IGMP timer expiration, the switch
sends IGMP query packets to related VLAN member ports and
increments this object by 1.ro INTEGER .1.3.6.1.4.1.171.11.64.2.2.10.4.1.3 |
swL2IGMPInfoTableThe table containing current IGMP information which have been captured by
this device, provided that swL2DevCtrlIGMPSnooping and
swL2IGMPCtrlState of associated VLAN entries are all enabled. Note
that the priority of IGMP table entries is lower than the Filtering
Table, i.e. if there is a table hash collision between the
entries of the IGMP Table and the Filtering Table inside the switch H/W
address table, the Filtering Table entry will overwrite the
colliding entry of the IGMP Table. See swL2FilterMgmt description
also. SEQUENCE OF SwL2IGMPInfoEntry .1.3.6.1.4.1.171.11.64.2.2.10.5 |
swL2IGMPInfoEntryInformation about current IGMP information which was captured by
this device, provided that swL2DevCtrlIGMPSnooping and
swL2IGMPCtrlState of associated VLAN entries are all enabled. SwL2IGMPInfoEntry .1.3.6.1.4.1.171.11.64.2.2.10.5.1 |
swL2IGMPVidThis object indicates the VID of individual IGMP table entries.
It shows the VID of IGMP report information captured on
the network.ro INTEGER .1.3.6.1.4.1.171.11.64.2.2.10.5.1.1 |
swL2IGMPGroupIpAddrThis object identifies group ip address which have been captured from the
IGMP packet, on a per-Vlan basis.ro IpAddress .1.3.6.1.4.1.171.11.64.2.2.10.5.1.2 |
swL2IGMPMacAddrThis object identifies mac addresses which correspond
to swL2IGMPGroupIpAddr, on a per-Vlan basis.ro MacAddress (SNMPv2-TC) .1.3.6.1.4.1.171.11.64.2.2.10.5.1.3 |
swL2IGMPPortMapThis object indicates which ports belong to the same
multicast group, on a per-Vlan basis. Each multicast group has a
octect string to indicate with port map. The most significant
bit represents the lowest numbered port, and the least
significant bit represents the highest numbered port. Thus, each
port of the switch is represented by a single bit within the
value of this object. If that bit has a value of '1' then that
port is included in the set of ports; the port is not included
if its bit has a value of '0'(Note that the setting of the bit
corresponding to the port from which a frame is received is
irrelevant). The 4 octets represent one unit port according to
its logic port. If the unit has less then 32 port, the other ports don't
care and just fill in zero.ro PortList .1.3.6.1.4.1.171.11.64.2.2.10.5.1.4 |
swL2IGMPIpGroupReportCountThis object indicates how many report packets were received by the
device corresponding with this entry where the IGMP function is enabled,
on a per-Vlan basis.ro INTEGER .1.3.6.1.4.1.171.11.64.2.2.10.5.1.5 |
swL2IGMPMulticastVlanTableThe information of the IGMP snooping multicast VLAN table. SEQUENCE OF SwL2IGMPMulticastVlanEntry .1.3.6.1.4.1.171.11.64.2.2.10.6 |
swL2IGMPMulticastVlanEntryThe entry of swL2IGMPMulticastVlanTable. SwL2IGMPMulticastVlanEntry .1.3.6.1.4.1.171.11.64.2.2.10.6.1 |
swL2IGMPMulticastVlanidThis object indicates the VLAN id of the IGMP snooping multicast
VLAN entry.ro INTEGER .1.3.6.1.4.1.171.11.64.2.2.10.6.1.1 |
swL2IGMPMulticastVlanNameThis object indicates the VLAN name of the IGMP snooping multicast
VLAN entry.rw SnmpAdminString .1.3.6.1.4.1.171.11.64.2.2.10.6.1.2 |
swL2IGMPMulticastVlanSourcePortThis object indicates the portlist of the source ports of IGMP
snooping multicast VLAN. The source ports will be set as tag ports
of the VLAN entry and the IGMP control messages received from the
member ports would be forwarded to the source ports.rw PortList .1.3.6.1.4.1.171.11.64.2.2.10.6.1.3 |
swL2IGMPMulticastVlanMemberPortThis object indicates the portlist of the member ports of IGMP
snooping multicast VLAN. The source ports will be set to untag ports
of the vlan entry and the IGMP control messages received from the
member ports would be forwarded to the source ports.rw PortList .1.3.6.1.4.1.171.11.64.2.2.10.6.1.4 |
swL2IGMPMulticastVlanRowStatusThis object indicates the status of this entry.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.171.11.64.2.2.10.6.1.5 |
swL2IGMPMulticastVlanReplaceSourceIPThis object is used to replace the source IP address in the IP header for
IGMP control packets.rw IpAddress .1.3.6.1.4.1.171.11.64.2.2.10.6.1.6 |
swL2IGMPRouterPortTableThe information of the router port table. SEQUENCE OF SwL2IGMPRouterPortEntry .1.3.6.1.4.1.171.11.64.2.2.10.7 |
swL2IGMPRouterPortEntryThe entry of swL2IGMPRouterPortTable. SwL2IGMPRouterPortEntry .1.3.6.1.4.1.171.11.64.2.2.10.7.1 |
swL2IGMPRouterPortVlanidThis object indicates the VLAN id of the router port entry.ro INTEGER .1.3.6.1.4.1.171.11.64.2.2.10.7.1.1 |
swL2IGMPRouterPortVlanNameThis object indicates the VLAN name of the router port entry.ro SnmpAdminString .1.3.6.1.4.1.171.11.64.2.2.10.7.1.2 |
swL2IGMPRouterPortStaticPortListThis object indicates the static portlist of the router port entry.rw PortList .1.3.6.1.4.1.171.11.64.2.2.10.7.1.3 |
swL2IGMPRouterPortDynamicPortListThis object indicates the dynamic portlist of the router port entry.ro PortList .1.3.6.1.4.1.171.11.64.2.2.10.7.1.4 |
swL2IGMPRouterPortForbiddenPortListThis object indicates the forbidden portlist of the router port entry.rw PortList .1.3.6.1.4.1.171.11.64.2.2.10.7.1.5 |
swL2DhcpRelayMgmt OBJECT IDENTIFIER .1.3.6.1.4.1.171.11.64.2.2.11 |
swL2DhcpRelayStateThis object indicates if the DHCP relay function is enabled or
disabled.rwobsolete Enumeration .1.3.6.1.4.1.171.11.64.2.2.11.1 |
swL2DhcpRelayHopCountThis object indicates the maximum number of router hops that
the DHCP packets can cross.rwobsolete INTEGER .1.3.6.1.4.1.171.11.64.2.2.11.2 |
swL2DhcpRelayTimeThresholdThis object indicates the minimum time in seconds within which
the switch must relay the DHCP request. If this time is
exceeded, the switch will drop the DHCP packet.rwobsolete INTEGER .1.3.6.1.4.1.171.11.64.2.2.11.3 |
swL2DhcpRelayOption82StateThis object indicates if the DHCP relay agent information option 82
function is enabled or disabled.rwobsolete Enumeration .1.3.6.1.4.1.171.11.64.2.2.11.4 |
swL2DhcpRelayOption82CheckThis object indicates if the checking mechanism of DHCP relay agent
information option 82 is enabled or disabled.rwobsolete Enumeration .1.3.6.1.4.1.171.11.64.2.2.11.5 |
swL2DhcpRelayOption82PolicyThis object indicates the re-forwarding policy is DHCP relay agent
information option 82.
replace(1) - replace the exiting option 82 field in messages.
drop(2) - discard messages with existing option 82 field.
keep(3) - retain the existing option 82 field in messages.rwobsolete Enumeration .1.3.6.1.4.1.171.11.64.2.2.11.6 |
swL2DhcpRelayCtrlTableThis table specifies the IP address og the destination to forward
(relay) DHCP packets to.obsolete SEQUENCE OF SwL2DhcpRelayCtrlEntry .1.3.6.1.4.1.171.11.64.2.2.11.7 |
swL2DhcpRelayCtrlEntryA list of information specifying the IP address as a destination
to forward (relay) DHCP packets to.obsolete SwL2DhcpRelayCtrlEntry .1.3.6.1.4.1.171.11.64.2.2.11.7.1 |
swL2DhcpRelayCtrlInterfaceNameThe name of the IP interface.roobsolete DisplayString .1.3.6.1.4.1.171.11.64.2.2.11.7.1.1 |
swL2DhcpRelayCtrlServerThe DHCP server IP address.roobsolete IpAddress .1.3.6.1.4.1.171.11.64.2.2.11.7.1.2 |
swL2DhcpRelayCtrlStateThis object indicates the status of this entry.
other(1) - this entry is currently in use but the conditions
under which it will remain so are different from each of
the following values.
invalid(2) - writing this value to the object, results in the
corresponding entry being removed from the table.
valid(3) - this entry will reside in the table.rwobsolete Enumeration .1.3.6.1.4.1.171.11.64.2.2.11.7.1.3 |
swL2LoopDetectMgmt OBJECT IDENTIFIER .1.3.6.1.4.1.171.11.64.2.2.12 |
swL2LoopDetectCtrl OBJECT IDENTIFIER .1.3.6.1.4.1.171.11.64.2.2.12.1 |
swL2LoopDetectAdminStateThis object indicates the loopback detection status of the system.rw Enumeration .1.3.6.1.4.1.171.11.64.2.2.12.1.1 |
swL2LoopDetectIntervalThis object indicates the interval value, the range is from 1 to 32767 seconds.rw INTEGER .1.3.6.1.4.1.171.11.64.2.2.12.1.2 |
swL2LoopDetectRecoverTimeThis object indicates the recover time, the range is from 60 to 1000000.
A value of 0 disables the recover function.rw INTEGER .1.3.6.1.4.1.171.11.64.2.2.12.1.3 |
swL2LoopDetectModeThis object indicates the loopback detection mode for the system.rw Enumeration .1.3.6.1.4.1.171.11.64.2.2.12.1.4 |
swL2LoopDetectPortMgmt OBJECT IDENTIFIER .1.3.6.1.4.1.171.11.64.2.2.12.2 |
swL2LoopDetectPortTableThe table specifies the loopback detection function specified by the port. SEQUENCE OF SwL2LoopDetectPortEntry .1.3.6.1.4.1.171.11.64.2.2.12.2.1 |
swL2LoopDetectPortEntryThe table specifies the loopback detection function specified by the port. SwL2LoopDetectPortEntry .1.3.6.1.4.1.171.11.64.2.2.12.2.1.1 |
swL2LoopDetectPortIndexThis object indicates the module's port number. The range is from 1 to
the maximum port number specified in the modulero INTEGER .1.3.6.1.4.1.171.11.64.2.2.12.2.1.1.1 |
swL2LoopDetectPortStateThis object indicates the loopback detection function state on the port.rw Enumeration .1.3.6.1.4.1.171.11.64.2.2.12.2.1.1.2 |
swL2LoopDetectPortLoopVLANThis object indicates the VLAN list that has detected a loopback.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.171.11.64.2.2.12.2.1.1.3 |
swL2LoopDetectPortLoopStatusThis object indicates the port status.ro Enumeration .1.3.6.1.4.1.171.11.64.2.2.12.2.1.1.4 |
swL2TrafficSegMgmt OBJECT IDENTIFIER .1.3.6.1.4.1.171.11.64.2.2.13 |
swL2TrafficSegTableThis table specifies that the port can just forward traffic to the
specific port list. SEQUENCE OF SwL2TrafficSegEntry .1.3.6.1.4.1.171.11.64.2.2.13.1 |
swL2TrafficSegEntryA list of information specifying the port with its traffic
forward list. SwL2TrafficSegEntry .1.3.6.1.4.1.171.11.64.2.2.13.1.1 |
swL2TrafficSegPortThe port number of the logical port.ro INTEGER .1.3.6.1.4.1.171.11.64.2.2.13.1.1.1 |
swL2TrafficSegForwardPortsThe port list that the specific port can forward traffic to.rw PortList .1.3.6.1.4.1.171.11.64.2.2.13.1.1.2 |
swL2PortSecurityMgmt OBJECT IDENTIFIER .1.3.6.1.4.1.171.11.64.2.2.14 |
swL2PortSecurityControlTableport security feature which controls the address learning capability and the
traffic forwarding decision. Each port can have this function enabled or disabled.
When it is enabled and a number is given said N, which allows N addresses to be
learned at this port, the first N learned addresses are locked at this port as
static entry. When the learned addresses number reaches N, any incoming packet that
has not learned a source addresses is discarded (e.g. dropped) and no more new addresses
can be learned on this port. SEQUENCE OF SwL2PortSecurityControlEntry .1.3.6.1.4.1.171.11.64.2.2.14.1 |
swL2PortSecurityControlEntryA list of information contained in swL2PortSecurityControlTable. SwL2PortSecurityControlEntry .1.3.6.1.4.1.171.11.64.2.2.14.1.1 |
swL2PortSecurityPortIndexIndicates the secured port to lock address learning.ro INTEGER .1.3.6.1.4.1.171.11.64.2.2.14.1.1.1 |
swL2PortSecurityMaxLernAddrIndicates allowable number of addresses to be learned at this port.rw INTEGER .1.3.6.1.4.1.171.11.64.2.2.14.1.1.2 |
swL2PortSecurityModeIndicates the mode of locking address.
In deleteOnTimeout(3) mode - the locked addresses can be aged out after aging timer
has expired. In this mode, when the locked address has aged
out, the number of addresses that can be learned has to
increase by one.
In deleteOnReset(4) mode - never age out the locked addresses unless restarting
the system to prevent from port movement or intrusion.rw Enumeration .1.3.6.1.4.1.171.11.64.2.2.14.1.1.3 |
swL2PortSecurityAdmStateIndicates the administration state of the locking address.rw Enumeration .1.3.6.1.4.1.171.11.64.2.2.14.1.1.4 |
swL2PortSecurityTrapLogStatewhen enable(2),whenever there's a new MAC that violates the pre-defined
port security configuration, a trap will be sent out and the relevant information
will be logged in system.rw Enumeration .1.3.6.1.4.1.171.11.64.2.2.14.2 |
swL2MgmtMIBTraps OBJECT IDENTIFIER .1.3.6.1.4.1.171.11.64.2.2.15 |
swL2MgmtMIBTrapPrefix OBJECT IDENTIFIER .1.3.6.1.4.1.171.11.64.2.2.15.0 |
swL2macNotificationThis trap indicate the MAC addresses variation in the address table . NOTIFICATION-TYPE .1.3.6.1.4.1.171.11.64.2.2.15.0.3 |
swL2porttypechgNotificationThis trap indicates the port type change. NOTIFICATION-TYPE .1.3.6.1.4.1.171.11.64.2.2.15.0.4 |
swPowerStatusChgPower Status change notification. The notification is issued
when the swPowerStatus changes as in the following cases:
lowVoltage -> overCurrent.
lowVoltage -> working.
lowVoltage -> disconnect.
lowVoltage -> connect.
overCurrent -> lowVoltage.
overCurrent -> working.
overCurrent -> disconnect.
overCurrent -> connect.
working -> lowVoltage.
working -> overCurrent.
working -> connect.
working -> disconnect.
fail -> connect.
fail -> disconnect.
connect -> lowVoltage.
connect -> overCurrent.
connect -> working.
connect -> disconnect.
disconnect -> lowVoltage.
disconnect -> overCurrent.
disconnect -> working.
disconnect -> connect. NOTIFICATION-TYPE .1.3.6.1.4.1.171.11.64.2.2.15.0.5 |
swPowerFailurePower Failure notification. The notification issues
when the swPowerStatus changes as in the following cases:
lowVoltage -> fail.
overCurrent -> fail.
working -> fail.
connect -> fail.
disconnect -> fail. NOTIFICATION-TYPE .1.3.6.1.4.1.171.11.64.2.2.15.0.6 |
swPowerRecoverPower Recover notification. The notification issues
when the swPowerStatus changes as in the following cases:
fail -> lowVoltage.
fail -> overCurrent.
fail -> working. NOTIFICATION-TYPE .1.3.6.1.4.1.171.11.64.2.2.15.0.7 |
swl2NotificationBidings OBJECT IDENTIFIER .1.3.6.1.4.1.171.11.64.2.2.15.1 |
swL2macNotifyInfoThis object indicates information about the last time the system rebooted.ro OCTET STRING .1.3.6.1.4.1.171.11.64.2.2.15.1.1 |
swl2NotifyPortSecurity OBJECT IDENTIFIER .1.3.6.1.4.1.171.11.64.2.2.15.2 |
swL2PortSecurityViolationMacThis object indicates the MAC address that violated the port security configuration.ro MacAddress (SNMPv2-TC) .1.3.6.1.4.1.171.11.64.2.2.15.2.1 |
swL2PortSecurityViolationTrapWhen the port_security trap is enabled, if there's a new MAC that violates the pre-defined
port security configuration a trap will be sent out NOTIFICATION-TYPE .1.3.6.1.4.1.171.11.64.2.2.15.2.2 |
swl2NotifyIpMacBinding OBJECT IDENTIFIER .1.3.6.1.4.1.171.11.64.2.2.15.3 |
swL2IpMacBindingViolationIPThis object indicates the MAC address that violates the IP-Mac Binging configuration.ro MacAddress (SNMPv2-TC) .1.3.6.1.4.1.171.11.64.2.2.15.3.1 |
swL2IpMacBindingViolationMacThis object indicates the IP address that violates the IP-Mac Binging configuration.ro MacAddress (SNMPv2-TC) .1.3.6.1.4.1.171.11.64.2.2.15.3.2 |
swL2IpMacBindingViolationTrapWhen the IP-Mac Binding trap is enabled, if there's a new MAC that violates the pre-defined
port security configuration a trap will be sent out NOTIFICATION-TYPE .1.3.6.1.4.1.171.11.64.2.2.15.3.3 |
swl2NotifyLoopDetect OBJECT IDENTIFIER .1.3.6.1.4.1.171.11.64.2.2.15.4 |
swL2VlanLoopDetectVIDThis object indicates the VID that has detected a loopback.ro INTEGER .1.3.6.1.4.1.171.11.64.2.2.15.4.1 |
swL2PortLoopOccurredThe trap is sent when a Port loop occurs. NOTIFICATION-TYPE .1.3.6.1.4.1.171.11.64.2.2.15.4.2 |
swL2PortLoopRestartThe trap is sent when a Port loop restarts after the interval time. NOTIFICATION-TYPE .1.3.6.1.4.1.171.11.64.2.2.15.4.3 |
swL2VlanLoopOccurredThe trap is sent when a Port with a VID loop occurs. NOTIFICATION-TYPE .1.3.6.1.4.1.171.11.64.2.2.15.4.4 |
swL2VlanLoopRestartThe trap is sent when a Port with a VID loop restarts after the interval time. NOTIFICATION-TYPE .1.3.6.1.4.1.171.11.64.2.2.15.4.5 |
swL2DhcpLocalRelayMgmt OBJECT IDENTIFIER .1.3.6.1.4.1.171.11.64.2.2.24 |
swL2DhcpLocalRelayStateThis object indicates the status of the DHCP local relay
function of the switch.rw Enumeration .1.3.6.1.4.1.171.11.64.2.2.24.1 |
swL2DhcpLocalRelayVLANTableThis table is used to manage the DHCP local relay status
for each VLAN. SEQUENCE OF SwL2DhcpLocalRelayVLANEntry .1.3.6.1.4.1.171.11.64.2.2.24.2 |
swL2DhcpLocalRelayVLANEntryThis object lists the current VLANs in the switch and their
corresponding DHCP local relay status. SwL2DhcpLocalRelayVLANEntry .1.3.6.1.4.1.171.11.64.2.2.24.2.1 |
swL2DhcpLocalRelayVLANIDThis object shows the VIDs of the current VLANS in the switch.ro INTEGER .1.3.6.1.4.1.171.11.64.2.2.24.2.1.1 |
swL2DhcpLocalRelayVLANStateThis object indicates the status of the DHCP relay function
of the VLAN.rw Enumeration .1.3.6.1.4.1.171.11.64.2.2.24.2.1.2 |