DES3326S-L2MGMT-MIB
The Structure of Layer 2 Network Management Information for the proprietary enterprise.
Main OID:
swL2MgmtMIB.1.3.6.1.4.1.171.11.49.1.1.2
146
Objects
Active
Status
4
Dependencies
Imported Objects
Objects
146 total| Object Name |
|---|
swL2MgmtMIBThe Structure of Layer 2 Network Management Information for the
proprietary enterprise. MODULE-IDENTITY .1.3.6.1.4.1.171.11.49.1.1.2 |
swL2DevMgmt OBJECT IDENTIFIER .1.3.6.1.4.1.171.11.49.1.1.2.1 |
swL2DevInfo OBJECT IDENTIFIER .1.3.6.1.4.1.171.11.49.1.1.2.1.1 |
swDevInfoSystemUpTimeThe value of sysUpTime at the time the switch entered its
current operational state. If the current state was entered
prior to the last re-initialization, then this object contains
a zero value. This value is in units of seconds.ro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.171.11.49.1.1.2.1.1.1 |
swDevInfoTotalNumOfPortThe number of ports within this switch. This value is the sum
of the ports within this switch.ro INTEGER .1.3.6.1.4.1.171.11.49.1.1.2.1.1.2 |
swDevInfoNumOfPortInUseThe number of ports in this switch connected to the segment or
the end stations.ro INTEGER .1.3.6.1.4.1.171.11.49.1.1.2.1.1.3 |
swDevInfoConsoleInUseThis usage indication of console system.ro Enumeration .1.3.6.1.4.1.171.11.49.1.1.2.1.1.4 |
swDevInfoModuleTypeThis object indicates the module type of this port.ro OCTET STRING .1.3.6.1.4.1.171.11.49.1.1.2.1.1.5 |
swL2DevCtrlUpDownloadStatestatus of upload/download control. If the value is 'other',
means never firmware updated since device started up.ro Enumeration .1.3.6.1.4.1.171.11.49.1.1.2.1.1.6 |
swDevInfoSaveCfgThis object indicates the status of the device configuration.
other(1) - this entry is currently in use but the conditions
under which it will remain so are different from each
of the following values.
proceeding(2) - the device configuration is saving into the
NV-RAM.
ready(3) - the device configuration has been ready to save into
NV-RAM.
failed(4) - The processing of saving device configuration is
failed.ro Enumeration .1.3.6.1.4.1.171.11.49.1.1.2.1.1.7 |
swDevInfoPowerTableA list of temperature. SEQUENCE OF SwDevInfoPowerEntry .1.3.6.1.4.1.171.11.49.1.1.2.1.1.8 |
swDevInfoPowerEntryA entry of Power information. SwDevInfoPowerEntry .1.3.6.1.4.1.171.11.49.1.1.2.1.1.8.1 |
swDevInfoPowerUnitIndexIndicates ID of the unit in the Systemro INTEGER .1.3.6.1.4.1.171.11.49.1.1.2.1.1.8.1.1 |
swDevInfoPowerIDIndicates ID of the powerro INTEGER .1.3.6.1.4.1.171.11.49.1.1.2.1.1.8.1.2 |
swDevInfoPowerStatusIndicates status of the powerro Enumeration .1.3.6.1.4.1.171.11.49.1.1.2.1.1.8.1.3 |
swL2DevCtrl OBJECT IDENTIFIER .1.3.6.1.4.1.171.11.49.1.1.2.1.2 |
swL2DevCtrlStpStateThis object can be enabled or disabled spanning tree algorithm
during runtime of the system.rw Enumeration .1.3.6.1.4.1.171.11.49.1.1.2.1.2.1 |
swL2DevCtrlIGMPSnoopingThis object indicates layer 2 Internet Group Management
Protocol (IGMP) capture function is enabled or disabled.rw Enumeration .1.3.6.1.4.1.171.11.49.1.1.2.1.2.2 |
swL2DevCtrlRmonStateThis object can be enabled or disabled RMON.rw Enumeration .1.3.6.1.4.1.171.11.49.1.1.2.1.2.3 |
swL2DevCtrlUpDownloadImageFileNameThe name of the image file to be uploaded/Downloaded from the
device to TFTP server when enabling image upload/download
function (by writing swL2DevCtrlUpDownloadImage).rw DisplayString .1.3.6.1.4.1.171.11.49.1.1.2.1.2.4 |
swL2DevCtrlUpDownloadImageSourceAddrThe ip address where been uploaded/Downloaded image file.rw IpAddress .1.3.6.1.4.1.171.11.49.1.1.2.1.2.5 |
swL2DevCtrlUpDownloadImageImage file upload/download control. After setting, it will
immediately invoke image upload/download function. While
retrieving the value of this object, it always returns 'other'
normally.rw Enumeration .1.3.6.1.4.1.171.11.49.1.1.2.1.2.6 |
swL2DevCtrlSaveCfgAs the object is set to active, the current device
configuration is save into to NV-RAM.If set to normal, do
nothing.rw Enumeration .1.3.6.1.4.1.171.11.49.1.1.2.1.2.7 |
swL2DevCtrlCleanAllStatisticCounterAs the object is set to active, all the statistic counters will
be cleared. If set to normal, do nothing.rw Enumeration .1.3.6.1.4.1.171.11.49.1.1.2.1.2.8 |
swL2DevCtrlVlanIdOfFDBTblIndicates the VLAN ID which the Dot1dTpFdbTable belongs to ;
The default value is DEFAULT_VLAN_ID of system .rw VlanId .1.3.6.1.4.1.171.11.49.1.1.2.1.2.9 |
swL2MACNotifyStateThis object can enabled or disabled MAC Notification.rw Enumeration .1.3.6.1.4.1.171.11.49.1.1.2.1.2.10 |
swL2MACNotifyHistorySizeThis object indicates the history size of variation MAC in address table.
The default value is 1 .rw INTEGER .1.3.6.1.4.1.171.11.49.1.1.2.1.2.11 |
swL2MACNotifyIntervalThis object indicates the time interval in second for trigger the MAC notify message.rw INTEGER .1.3.6.1.4.1.171.11.49.1.1.2.1.2.12 |
swL2DevAlarm OBJECT IDENTIFIER .1.3.6.1.4.1.171.11.49.1.1.2.1.3 |
swL2DevAlarmNewRootWhen the device has become the new root of the Spanning Tree,
this object decide whether to send a new root trap.rw Enumeration .1.3.6.1.4.1.171.11.49.1.1.2.1.3.1 |
swL2DevAlarmTopologyChangeThis object determine to send a trap or not when the switch
topology was changed. If the object is enabled(3),
the topologyChange trap is sent by the device when any of its
configured ports transitions from the Learning state to the
Forwarding state, or from the Forwarding state to the Blocking
state. For the same port tranition, the device doesn't send the
trap if this object value is disabled or other.rw Enumeration .1.3.6.1.4.1.171.11.49.1.1.2.1.3.2 |
swL2DevAlarmLinkChangeThis object determine to send a trap or not when the link
was changed. If the object is enabled(3), the Link Change
trap is sent by the device when any of its ports link change.
The device doesn't send the trap if this object value is
disabled or other.rw Enumeration .1.3.6.1.4.1.171.11.49.1.1.2.1.3.3 |
swL2PortMgmt OBJECT IDENTIFIER .1.3.6.1.4.1.171.11.49.1.1.2.4 |
swL2PortInfoTableA table that contains information about every port. SEQUENCE OF SwL2PortInfoEntry .1.3.6.1.4.1.171.11.49.1.1.2.4.1 |
swL2PortInfoEntryA list of information for each port of the device. SwL2PortInfoEntry .1.3.6.1.4.1.171.11.49.1.1.2.4.1.1 |
swL2PortInfoPortIndexThis object indicates the module's port number.(1..Max port
number in the module)ro INTEGER .1.3.6.1.4.1.171.11.49.1.1.2.4.1.1.1 |
swL2PortInfoUnitIndexIndicates ID of the unit in the devicero INTEGER .1.3.6.1.4.1.171.11.49.1.1.2.4.1.1.2 |
swL2PortInfoTypeThis object indicates the connector type of this port.ro Enumeration .1.3.6.1.4.1.171.11.49.1.1.2.4.1.1.3 |
swL2PortInfoLinkStatusThis object indicates the port link status.ro Enumeration .1.3.6.1.4.1.171.11.49.1.1.2.4.1.1.4 |
swL2PortInfoNwayStatusThis object indicates the port speed and duplex mode.ro Enumeration .1.3.6.1.4.1.171.11.49.1.1.2.4.1.1.5 |
swL2PortInfoModuleTypeThis object indicates the module type of this port.ro Enumeration .1.3.6.1.4.1.171.11.49.1.1.2.4.1.1.6 |
swL2PortCtrlTableA table that contains control information about every port. SEQUENCE OF SwL2PortCtrlEntry .1.3.6.1.4.1.171.11.49.1.1.2.4.2 |
swL2PortCtrlEntryA list of control information for each port of the device. SwL2PortCtrlEntry .1.3.6.1.4.1.171.11.49.1.1.2.4.2.1 |
swL2PortCtrlPortIndexThis object indicates the module's port number.(1..Max port
number in the module)ro INTEGER .1.3.6.1.4.1.171.11.49.1.1.2.4.2.1.1 |
swL2PortCtrlUnitIndexIndicates ID of the unit in the devicero INTEGER .1.3.6.1.4.1.171.11.49.1.1.2.4.2.1.2 |
swL2PortCtrlAdminStateThis object decide the port enabled or disabled.rw Enumeration .1.3.6.1.4.1.171.11.49.1.1.2.4.2.1.3 |
swL2PortCtrlNwayStateChose the port speed, duplex mode, and N-Way function mode.rw Enumeration .1.3.6.1.4.1.171.11.49.1.1.2.4.2.1.4 |
swL2PortCtrlFlowCtrlStateThe flow control mechanism is different between full duplex
mode and half duplex mode. For half duplex mode, the jamming
signal is asserted. For full duplex mode, IEEE 802.3x flow
control function sends PAUSE frames and receives PAUSE frames.rw Enumeration .1.3.6.1.4.1.171.11.49.1.1.2.4.2.1.5 |
swL2PortCtrlLockStateThis object decide the port is locked or not.rw Enumeration .1.3.6.1.4.1.171.11.49.1.1.2.4.2.1.6 |
swL2PortCtrlMACNotifyStateThis object decide the MAC notification is enable not.rw Enumeration .1.3.6.1.4.1.171.11.49.1.1.2.4.2.1.7 |
swL2PortCtrlMulticastfilterThis object decide the multicast packets filtering mode on this port .rw Enumeration .1.3.6.1.4.1.171.11.49.1.1.2.4.2.1.8 |
swL2QOSMgmt OBJECT IDENTIFIER .1.3.6.1.4.1.171.11.49.1.1.2.6 |
swL2QOSBandwidthControlTable. SEQUENCE OF SwL2QOSBandwidthControlEntry .1.3.6.1.4.1.171.11.49.1.1.2.6.1 |
swL2QOSBandwidthControlEntryA list of information contained in swL2QOSBandwidthControlTable. SwL2QOSBandwidthControlEntry .1.3.6.1.4.1.171.11.49.1.1.2.6.1.1 |
swL2QOSBandwidthPortIndexIndicates the port .ro INTEGER .1.3.6.1.4.1.171.11.49.1.1.2.6.1.1.1 |
swL2QOSBandwidthRxRateIndicates RX Rate(Mbit/sec) of the specifed port. Value 0 means no limit.rw INTEGER .1.3.6.1.4.1.171.11.49.1.1.2.6.1.1.2 |
swL2QOSBandwidthTxRateIndicates TX Rate(Mbit/sec) of the specifed port. Value 0 means no limit.rw INTEGER .1.3.6.1.4.1.171.11.49.1.1.2.6.1.1.3 |
swL2QOSSchedulingTable. SEQUENCE OF SwL2QOSSchedulingEntry .1.3.6.1.4.1.171.11.49.1.1.2.6.2 |
swL2QOSSchedulingEntryA list of information contained in swL2QOSSchedulingTable. SwL2QOSSchedulingEntry .1.3.6.1.4.1.171.11.49.1.1.2.6.2.1 |
swL2QOSSchedulingClassIndexIndicates the hardware queue number.ro INTEGER .1.3.6.1.4.1.171.11.49.1.1.2.6.2.1.1 |
swL2QOSSchedulingMaxPktsIndicates the maximum number of packets the hardware priority queue will be allowed
to transmit before allowing the next lowest priority queue to transmit its packets.
a value between 0 and 255 can be specified.rw INTEGER .1.3.6.1.4.1.171.11.49.1.1.2.6.2.1.2 |
swL2QOSSchedulingMaxLatencyIndicates the maximum amount of time the hardware priority queue will be allowed
to transmit packets before allowing the next lowest priority queue to begin transmit
its packets. A value between 0 and 255 can be specified- with this value multiplied
by 16 ms to arrive at the total allowed time for queue to transmit packets.
For example, a value of 3 specifies 3*16=48 ms. The queue will continue transmitting
the last packet until it is finished when the max_latency timer expires.rw INTEGER .1.3.6.1.4.1.171.11.49.1.1.2.6.2.1.3 |
swL2QOS8021pUserPriorityTable. SEQUENCE OF SwL2QOS8021pUserPriorityEntry .1.3.6.1.4.1.171.11.49.1.1.2.6.3 |
swL2QOS8021pUserPriorityEntryA list of information contained in swL2QOS8021pUserPriorityTable. SwL2QOS8021pUserPriorityEntry .1.3.6.1.4.1.171.11.49.1.1.2.6.3.1 |
swL2QOS8021pUserPriorityIndexThe 802.1p user priority .ro INTEGER .1.3.6.1.4.1.171.11.49.1.1.2.6.3.1.1 |
swL2QOS8021pUserPriorityClassThe number of the switch's hardware priority queue. The switch has four hardware
priority queues available. They are numbered between 0 (the lowest priority)
and 3 (the highest priority).rw INTEGER .1.3.6.1.4.1.171.11.49.1.1.2.6.3.1.2 |
swL2QOS8021pDefaultPriorityTable. SEQUENCE OF SwL2QOS8021pDefaultPriorityEntry .1.3.6.1.4.1.171.11.49.1.1.2.6.4 |
swL2QOS8021pDefaultPriorityEntryA list of information contained in swL2QOS8021pDefaultPriorityTable. SwL2QOS8021pDefaultPriorityEntry .1.3.6.1.4.1.171.11.49.1.1.2.6.4.1 |
swL2QOS8021pDefaultPriorityIndexIndicates the port number .ro INTEGER .1.3.6.1.4.1.171.11.49.1.1.2.6.4.1.1 |
swL2QOS8021pDefaultPriorityThe priority value to assign to untagged packets received by the
switch ports on the switch..rw INTEGER .1.3.6.1.4.1.171.11.49.1.1.2.6.4.1.2 |
swL2TrunkMgmt OBJECT IDENTIFIER .1.3.6.1.4.1.171.11.49.1.1.2.8 |
swL2TrunkMaxSupportedEntriesMaximum number of entries in the trunk configuration table
(swL2TrunkCtrlTable).ro INTEGER .1.3.6.1.4.1.171.11.49.1.1.2.8.1 |
swL2TrunkCurrentNumEntriesCurrent actived number of entries in the trunk configuration
table.ro INTEGER .1.3.6.1.4.1.171.11.49.1.1.2.8.2 |
swL2TrunkCtrlTableThis table specifys which ports group a set of ports(up to 8)
into a single logical link. SEQUENCE OF SwL2TrunkCtrlEntry .1.3.6.1.4.1.171.11.49.1.1.2.8.3 |
swL2TrunkCtrlEntryA list of information specifies which ports group a set of
ports(up to 8) into a single logical link. SwL2TrunkCtrlEntry .1.3.6.1.4.1.171.11.49.1.1.2.8.3.1 |
swL2TrunkIndexThe index of logical port trunk. The trunk group number depend
on the existence of unit and module.ro INTEGER .1.3.6.1.4.1.171.11.49.1.1.2.8.3.1.1 |
swL2TrunkNameThe name of logical port trunk.rw DisplayString .1.3.6.1.4.1.171.11.49.1.1.2.8.3.1.2 |
swL2TrunkMasterPortThe object indicates the master port number of the port trunk
entry. When using Port Trunk, you can not configure the other
ports of the group except the master port.
Their configuration must be same as the master port (e.g. speed,
duplex, enabled/disabled, flow control, and so on).rw INTEGER .1.3.6.1.4.1.171.11.49.1.1.2.8.3.1.3 |
swL2TrunkMemberIndicate how many number of ports is included in this Trunk.
The trunk port number depend on the existence of module.
The maximum number of ports is 8 for one trunks.rw PortList .1.3.6.1.4.1.171.11.49.1.1.2.8.3.1.4 |
swL2TrunkFloodingPortThe object indicates the flooding port number of the port trunk
entry. The first port of the trunk is implicitly configured to
be the flooding port.ro INTEGER .1.3.6.1.4.1.171.11.49.1.1.2.8.3.1.5 |
swL2TrunkTypeThis object indicated that type of the trunk group.
static : is static trunk group
lacp : is LACP trunk group .rw Enumeration .1.3.6.1.4.1.171.11.49.1.1.2.8.3.1.6 |
swL2TrunkStateThis object indicates the status of this entry.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.171.11.49.1.1.2.8.3.1.7 |
swL2TrunkAlgorithmThis object configures to part of the packet examined by the
switch when selecting the egress port for transmitting
load-sharing data.rw Enumeration .1.3.6.1.4.1.171.11.49.1.1.2.8.4 |
swL2MirrorMgmt OBJECT IDENTIFIER .1.3.6.1.4.1.171.11.49.1.1.2.9 |
swL2MirrorLogicTargetPortThis object indicates switch which port will sniff another
port. A trunk port member cannot be configured as a target
Snooping port. The port number is the sequential (logical)
number which is also applied to bridge MIB, etc.rw INTEGER .1.3.6.1.4.1.171.11.49.1.1.2.9.1 |
swL2MirrorPortSourceIngressThe represent the ingress into the source port packet to
sniffed.rw PortList .1.3.6.1.4.1.171.11.49.1.1.2.9.2 |
swL2MirrorPortSourceEgressThe represent the egress from the source port packet to
sniffed.rw PortList .1.3.6.1.4.1.171.11.49.1.1.2.9.3 |
swL2MirrorPortStateThis object indicates the port mirroring state.
other(1) - this entry is currently in use but the conditions
under which it will remain so are different from each of the
following values.
disabled(2) - writing this value to the object, and then the
corresponding entry will be removed from the table.
enabled(3) - this entry is reside in the table.rw Enumeration .1.3.6.1.4.1.171.11.49.1.1.2.9.4 |
swL2IGMPMgmt OBJECT IDENTIFIER .1.3.6.1.4.1.171.11.49.1.1.2.10 |
swL2IGMPMaxSupportedVlansMaximum number of Vlans in the layer 2 IGMP control table
(swL2IGMPCtrlTable).ro INTEGER .1.3.6.1.4.1.171.11.49.1.1.2.10.1 |
swL2IGMPMaxIpGroupNumPerVlanMaximum number of multicast ip group per Vlan in the layer 2
IGMP information table (swL2IGMPQueryInfoTable).ro INTEGER .1.3.6.1.4.1.171.11.49.1.1.2.10.2 |
swL2IGMPCtrlTableThe table controls the Vlan's IGMP function. Its scale depends
on current VLAN state (swL2VlanInfoStatus). If VLAN is disabled
mode, there is only one entry in the table, with index 1. If
VLAN is in Port-Base or 802.1q mode, the number of entries can
be up to 12, with index range from 1 to 12. SEQUENCE OF SwL2IGMPCtrlEntry .1.3.6.1.4.1.171.11.49.1.1.2.10.3 |
swL2IGMPCtrlEntryThe entry in IGMP control table (swL2IGMPCtrlTable). The entry
is effective only when IGMP capture switch
(swL2DevCtrlIGMPSnooping) is enabled. SwL2IGMPCtrlEntry .1.3.6.1.4.1.171.11.49.1.1.2.10.3.1 |
swL2IGMPCtrlVidThis object indicates the IGMP control entry's VLAN id. If VLAN
is disabled, the Vid is always 0 and cannot be changed by
management users. If VLAN is in Port-Base mode, the Vid is
arranged from 1 to 12, fixed form. If VLAN is in 802.1q mode,
the Vid setting can vary from 1 to 4094 by management user, and
the Vid in each entry must be unique in the IGMP Control Table.ro INTEGER .1.3.6.1.4.1.171.11.49.1.1.2.10.3.1.1 |
swL2IGMPQueryIntervalThe frequency at which IGMP Host-Query packets are
transmitted on this switch.rw INTEGER .1.3.6.1.4.1.171.11.49.1.1.2.10.3.1.2 |
swL2IGMPMaxResponseTimeThe maximum query response time on this switch.rw INTEGER .1.3.6.1.4.1.171.11.49.1.1.2.10.3.1.3 |
swL2IGMPRobustnessThe Robustness Variable allows tuning for the expected
packet loss on a subnet. If a subnet is expected to be
lossy, the Robustness Variable may be increased. IGMP is
robust to (Robustness Variable-1) packet losses.rw INTEGER .1.3.6.1.4.1.171.11.49.1.1.2.10.3.1.4 |
swL2IGMPLastMemberQueryIntervalThe Last Member Query Interval is the Max Response Time
inserted into Group-Specific Queries sent in response to
Leave Group messages, and is also the amount of time between
Group-Specific Query messages.rw INTEGER .1.3.6.1.4.1.171.11.49.1.1.2.10.3.1.5 |
swL2IGMPHostTimeoutThe timer value for sending IGMP query packet when none was
sent by the host in the LAN. The timer works in per-VLAN basis.
Our device will be activated to send the query message if the
timer is expired. Please reference RFC2236-1997.rw INTEGER .1.3.6.1.4.1.171.11.49.1.1.2.10.3.1.6 |
swL2IGMPRouteTimeoutThe Router Timeout is how long a host must wait after hearing
a Query before it may send any IGMPv2 messages.rw INTEGER .1.3.6.1.4.1.171.11.49.1.1.2.10.3.1.7 |
swL2IGMPLeaveTimerWhen a querier receives a Leave Group message for a group that
has group members on the reception interface, it sends
Group-Specific Queries every swL2IGMPLeaveTimer to the group
being left.rw INTEGER .1.3.6.1.4.1.171.11.49.1.1.2.10.3.1.8 |
swL2IGMPQueryStateThis object decide the IGMP query enabled or disabled.rw Enumeration .1.3.6.1.4.1.171.11.49.1.1.2.10.3.1.9 |
swL2IGMPCurrentStateThis object indicates the current IGMP query state.ro Enumeration .1.3.6.1.4.1.171.11.49.1.1.2.10.3.1.10 |
swL2IGMPCtrlStateThis object indicates the status of this entry.
other(1) - this entry is currently in use but the conditions under
which it will remain so are different from each of the following
values.
disable(2) - IGMP funtion is disabled for this entry.
enable(3) - IGMP funtion is enabled for this entry.rw Enumeration .1.3.6.1.4.1.171.11.49.1.1.2.10.3.1.11 |
swL2IGMPQueryInfoTableThe table contains the number current IGMP query packets which
is captured by this device, as well as the IGMP query packets
sent by the device. SEQUENCE OF SwL2IGMPQueryInfoEntry .1.3.6.1.4.1.171.11.49.1.1.2.10.4 |
swL2IGMPQueryInfoEntryInformation about current IGMP query information, provided that
swL2DevCtrlIGMPSnooping and swL2IGMPCtrState of associated VLAN
entry are all enabled. SwL2IGMPQueryInfoEntry .1.3.6.1.4.1.171.11.49.1.1.2.10.4.1 |
swL2IGMPInfoVidThis object indicates the Vid of associated IGMP info table
entry. It follows swL2IGMPCtrlVid in the associated entry of
IGMP control table (swL2IGMPCtrlTable).ro INTEGER .1.3.6.1.4.1.171.11.49.1.1.2.10.4.1.1 |
swL2IGMPInfoQueryCountThis object indicates the number of query packets received
since the IGMP function enabled, in per-VLAN basis.ro INTEGER .1.3.6.1.4.1.171.11.49.1.1.2.10.4.1.2 |
swL2IGMPInfoTxQueryCountThis object indicates the send count of IGMP query messages, in
per-VLAN basis. In case of IGMP timer expiration, the switch
sends IGMP query packets to related VLAN member ports and
increment this object by 1.ro INTEGER .1.3.6.1.4.1.171.11.49.1.1.2.10.4.1.3 |
swL2IGMPInfoTableThe table containing current IGMP information which captured by
this device, provided that swL2DevCtrlIGMPSnooping and
swL2IGMPCtrlState of associated VLAN entry are all enabled. Note
that the priority of IGMP table entries is lower than Filtering
Table, i.e. if there is a table hash collision between the
entries of IGMP Table and Filtering Table inside the switch H/W
address table, then Filtering Table entry overwrite the
colliding entry of IGMP Table. See swL2FilterMgmt description
also. SEQUENCE OF SwL2IGMPInfoEntry .1.3.6.1.4.1.171.11.49.1.1.2.10.5 |
swL2IGMPInfoEntryInformation about current IGMP information which captured by
this device, provided that swL2DevCtrlIGMPSnooping and
swL2IGMPCtrlState of associated VLAN entry are all enabled. SwL2IGMPInfoEntry .1.3.6.1.4.1.171.11.49.1.1.2.10.5.1 |
swL2IGMPVidThis object indicates the Vid of individual IGMP table entry.
It shows the Vid of IGMP report information captured on
network.ro INTEGER .1.3.6.1.4.1.171.11.49.1.1.2.10.5.1.1 |
swL2IGMPGroupIpAddrThis object is identify group ip address which is captured from
IGMP packet, in per-Vlan basis.ro IpAddress .1.3.6.1.4.1.171.11.49.1.1.2.10.5.1.2 |
swL2IGMPMacAddrThis object is identify mac address which is corresponding
to swL2IGMPGroupIpAddr, in per-Vlan basis.ro MacAddress (SNMPv2-TC) .1.3.6.1.4.1.171.11.49.1.1.2.10.5.1.3 |
swL2IGMPPortMapThis object indicates which ports are belong to the same
multicast group, in per-Vlan basis. Each multicast group has a
octect string to indicate with port map. The most significant
bit represents the lowest numbered port, and the least
significant bit represents the highest numbered port. Thus, each
port of the switch is represented by a single bit within the
value of this object. If that bit has a value of '1' then that
port is included in the set of ports; the port is not included
if its bit has a value of '0'(Note that the setting of the bit
corresponding to the port from which a frame is received is
irrelevant). The 4 octets is represent one unit port according
its logic port. If the unit less 32 port, the other port don't
care just fill zero.ro PortList .1.3.6.1.4.1.171.11.49.1.1.2.10.5.1.4 |
swL2IGMPIpGroupReportCountThis object indicate how much report packet was receive by our
device corresponding with this entry from IGMP function enabled,
in per-Vlan basis.ro INTEGER .1.3.6.1.4.1.171.11.49.1.1.2.10.5.1.5 |
swL2TrafficMgmt OBJECT IDENTIFIER .1.3.6.1.4.1.171.11.49.1.1.2.12 |
swL2TrafficCtrlTableThis table specifys the storm traffic control configuration. SEQUENCE OF SwL2TrafficCtrlEntry .1.3.6.1.4.1.171.11.49.1.1.2.12.1 |
swL2TrafficCtrlEntryA list of information specifies the storm traffic control
configuration. SwL2TrafficCtrlEntry .1.3.6.1.4.1.171.11.49.1.1.2.12.1.1 |
swL2TrafficCtrlGroupIndexThe index of logical port trunk. The trunk group number depend
on the existence of unit and module.ro INTEGER .1.3.6.1.4.1.171.11.49.1.1.2.12.1.1.1 |
swL2TrafficCtrlUnitIndexIndicates ID of the unit in the devicero INTEGER .1.3.6.1.4.1.171.11.49.1.1.2.12.1.1.2 |
swL2TrafficCtrlBMStromthresholdThis object to decide how much thousand packets per second
broadcast/multicast (depend on swL2TrafficCtrlBcastStromCtrl,
swL2TrafficCtrlMcastStromCtrl or swL2TrafficCtrlDlfStromCtrl
objects whether is enabled) will active storm control. Whenever
a port reaches its configured amount of packets in the one
second time interval, the device will start dropping that type
of packet, until the time interval has expired. Once the time
interval has expired, the device will start forwarding that type
of packet.rw INTEGER .1.3.6.1.4.1.171.11.49.1.1.2.12.1.1.3 |
swL2TrafficCtrlBcastStromCtrlThis object indicates broadcast storm control function is
enabled or disabled.rw Enumeration .1.3.6.1.4.1.171.11.49.1.1.2.12.1.1.4 |
swL2TrafficCtrlMcastStromCtrlThis object indicates multicast storm control function is
enabled or disabled.rw Enumeration .1.3.6.1.4.1.171.11.49.1.1.2.12.1.1.5 |
swL2TrafficCtrlDlfStromCtrlThis object indicates destination lookup fail function is
enabled or disabled.rw Enumeration .1.3.6.1.4.1.171.11.49.1.1.2.12.1.1.6 |
swL2TrafficSegMgmt OBJECT IDENTIFIER .1.3.6.1.4.1.171.11.49.1.1.2.13 |
swL2TrafficSegTableThis table specifys the port just can forward traffic to the
specific port list. SEQUENCE OF SwL2TrafficSegEntry .1.3.6.1.4.1.171.11.49.1.1.2.13.1 |
swL2TrafficSegEntryA list of information specifies the port with its traffic
forward list. SwL2TrafficSegEntry .1.3.6.1.4.1.171.11.49.1.1.2.13.1.1 |
swL2TrafficSegPortThe port number of the logical port.ro INTEGER .1.3.6.1.4.1.171.11.49.1.1.2.13.1.1.1 |
swL2TrafficSegForwardPortsThe port list that the specific port can forward traffic.rw PortList .1.3.6.1.4.1.171.11.49.1.1.2.13.1.1.2 |
swL2PortSecurityMgmt OBJECT IDENTIFIER .1.3.6.1.4.1.171.11.49.1.1.2.14 |
swL2PortSecurityControlTableport security feature which controls the address leaning capability and the
traffic forwarding decision. Each port can have this function enabled or disabled.
When it is enabled and a number is given said N, which allows N addresses to be
learned at this port, the first N learned addresses are locked at this port as
static entry. When the learned addresses number reach N, any coming packet with
not learned source addresses are discarded (e.g. dropped) and no more new addresses
can be learned at this port. SEQUENCE OF SwL2PortSecurityControlEntry .1.3.6.1.4.1.171.11.49.1.1.2.14.1 |
swL2PortSecurityControlEntryA list of information contained in swL2PortSecurityControlTable. SwL2PortSecurityControlEntry .1.3.6.1.4.1.171.11.49.1.1.2.14.1.1 |
swL2PortSecurityPortIndexIndicates the secured port to lock address learning.ro INTEGER .1.3.6.1.4.1.171.11.49.1.1.2.14.1.1.1 |
swL2PortSecurityMaxLernAddrIndicates allowable number of addresses to be learned at this port.rw INTEGER .1.3.6.1.4.1.171.11.49.1.1.2.14.1.1.2 |
swL2PortSecurityModeIndicates the mode of locking address.
In deleteOnTimeout(3) mode - the locked addresses can be aged out after aging timer
expire. In this mode, when the locked address is aged
out, the number of address can be learned has to be
increased by one.
In deleteOnReset(4) mode - never age out the locked addresses unless restart
the system to prevent from port movement or intrusion.rw Enumeration .1.3.6.1.4.1.171.11.49.1.1.2.14.1.1.3 |
swL2PortSecurityAdmStateIndicates administration state of locking address.rw Enumeration .1.3.6.1.4.1.171.11.49.1.1.2.14.1.1.4 |
swL2MgmtMIBTraps OBJECT IDENTIFIER .1.3.6.1.4.1.171.11.49.1.1.2.15 |
swL2MgmtMIBTrapPrefix OBJECT IDENTIFIER .1.3.6.1.4.1.171.11.49.1.1.2.15.0 |
swL2macNotificationThis trap indicate the mac addresses variation in address table . NOTIFICATION-TYPE .1.3.6.1.4.1.171.11.49.1.1.2.15.0.3 |
swL2porttypechgNotificationThis trap indicate the port type change. NOTIFICATION-TYPE .1.3.6.1.4.1.171.11.49.1.1.2.15.0.4 |
swPowerStatusChgPower Status change notification. NOTIFICATION-TYPE .1.3.6.1.4.1.171.11.49.1.1.2.15.0.5 |
swPowerFailurePower Failure notification. NOTIFICATION-TYPE .1.3.6.1.4.1.171.11.49.1.1.2.15.0.6 |
swPowerRecoverPower Recover notification. NOTIFICATION-TYPE .1.3.6.1.4.1.171.11.49.1.1.2.15.0.7 |
swl2NotificationBidings OBJECT IDENTIFIER .1.3.6.1.4.1.171.11.49.1.1.2.15.1 |
swL2macNotifyInfoThis object indicates the last time reboot information.ro OCTET STRING .1.3.6.1.4.1.171.11.49.1.1.2.15.1.1 |