DES3225G-MIB
Detailed view of the defined objects, syntax rules, and hierarchical paths.
114
Objects
Active
Status
4
Dependencies
Imported Objects
Objects
114 total| Object Name |
|---|
dlink OBJECT IDENTIFIER .1.3.6.1.4.1.171 |
RFC1155-SMI Unknown .1.3.6.1.4.1.171 |
dlink-products OBJECT IDENTIFIER .1.3.6.1.4.1.171.10 |
dlink-Des3225gProd OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.24 |
swProperty OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.24.1 |
portPartitionThe trap is sent whenever the port state enter the
Partion mode when more than 61 collisions occur while
trasmitting. TRAP-TYPE .1.3.6.1.4.1.171.10.24.1.0.1 |
linkChangeEventThe trap is sent whenever the link state of a port changes
from link up to link down or from link down to link up TRAP-TYPE .1.3.6.1.4.1.171.10.24.1.0.2 |
broadcastRisingStormThe trap indicates that broadcast higher rising threshold
. This trap including the port ID TRAP-TYPE .1.3.6.1.4.1.171.10.24.1.0.3 |
broadcastFallingStormThe trap indicates that broadcast higher falling threshold
. This trap including the port ID TRAP-TYPE .1.3.6.1.4.1.171.10.24.1.0.4 |
swModule OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.24.1.1 |
dlink-mgmt OBJECT IDENTIFIER .1.3.6.1.4.1.171.11 |
des3225gSeries OBJECT IDENTIFIER .1.3.6.1.4.1.171.11.24 |
swDevPackage OBJECT IDENTIFIER .1.3.6.1.4.1.171.11.24.1 |
swDevInfo OBJECT IDENTIFIER .1.3.6.1.4.1.171.11.24.1.1 |
swDevInfoSystemUpTimeThe value of sysUpTime at the time the switch entered its
current operational state. If the current state was entered
prior to the last re-initialization, then this object contains
a zero value. This value is in units of seconds.ro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.171.11.24.1.1.1 |
swDevInfoMaxNumOfModuleThe maximum number of modules in this device.ro INTEGER .1.3.6.1.4.1.171.11.24.1.1.2 |
swDevInfoTotalNumOfModuleThe current actual number of modules in this device.The values range is
1..swDevInfoMaxNumOfModule.ro INTEGER .1.3.6.1.4.1.171.11.24.1.1.3 |
swDevInfoTotalNumOfPortThe number of ports within this switch. This value is the sum
of the ports within this switch.ro INTEGER .1.3.6.1.4.1.171.11.24.1.1.4 |
swDevInfoNumOfPortInUseThe number of ports in this switch connected to the segment or
the end stations.ro INTEGER .1.3.6.1.4.1.171.11.24.1.1.5 |
swDevInfoConsoleInUseThis usage indication of console system.ro Enumeration .1.3.6.1.4.1.171.11.24.1.1.6 |
swDevInfoSystemLedStatusThis object is a set of system LED indications. The first four octets is
defined as system LED. The first LED is power LED. The second LED
is console LED. The third LED is GIGA module existing LED. The fourth LED
is GIGA module link LED. The other octets following the fourth octets
are the port LED. Every two bytes are presented to a port. The first
byte is presentd to the Link/Activity LED. The second byte is presented
to the Speed LED.
There is one byte per LED.
The most significant bit is used for blink/solid:
Off = The LED is lit permanently.
On = The LED blinks.
The three least significant bits are used for color:
1 = not lit,
2 = green,
3 = yellow,(orange)
4 = blue,
5 = red,
0+6+7 not used
The four remaining bits are currently unused and must be 0.
The lastest two octects are defined as slot module type. The first octect
is slot 1 module type. The second octect is slot 2 module type, and so on.
The module type representation for each byte is listed below:
1 = no slot module,
2 = 1 port BNC,
3 = 2 port Fiber MTRJ,
4 = 2 port TX UTP,
5 = 1 port Fiber SC,
6 = Gigabit
other not usedro OCTET STRING .1.3.6.1.4.1.171.11.24.1.1.7 |
swDevInfoSaveCfgThis object indicates the status of the device configuration.
other(1) - this entry is currently in use but the conditions
under which it will remain so are different from each
of the following values.
proceeding(2) - the device configuration is saving into the NV-RAM.
completed(3) V all of the device configuration parameters have been
saved into NV-RAM.
changed-not-save V some of the device configuration parameters have
been changed but not saved into NV-RAM.
failed(5) - The processing of saving device configuration is failed.ro Enumeration .1.3.6.1.4.1.171.11.24.1.1.8 |
swDevCtrl OBJECT IDENTIFIER .1.3.6.1.4.1.171.11.24.1.2 |
swDevCtrlStpStateThis object can be enabled or disabled spanning tree algorithm
during runtime of the system. When the device is in 802.1Q Vlan
mode, this object will be enabled and cannot be disabled.rw Enumeration .1.3.6.1.4.1.171.11.24.1.2.1 |
swDevIGMPCaptureStateThis object indicates Internet Group Management Protocol (IGMP) capture
function is enabled or disabled.rw Enumeration .1.3.6.1.4.1.171.11.24.1.2.2 |
swDevCtrlPartitionModeStateThis object used to enable or disable port auto partition. When the
object apply for all ports of the devicerw Enumeration .1.3.6.1.4.1.171.11.24.1.2.3 |
swDevCtrlTableLockStateThis object indicates whether the address table is locked.
In other words, the address table doesn't learn any more new address.
The aging timer is suspended when the address table is locked. As long
as the table is locked, all of the frames are dropped if the destination
can not be found in the address.When swVlanInfoStatus is in MAC-Base
VLAN mode, this object is always disabled.rw Enumeration .1.3.6.1.4.1.171.11.24.1.2.4 |
swDevCtrlSaveCfgAs the object is set, the current device configuration is save
into to NV-RAM.rw INTEGER .1.3.6.1.4.1.171.11.24.1.2.5 |
swDevCtrlHOLStateThe object provides a way to prevent HOL (Head Of Line) blocking
between ports. HOL protection may prevent forwarding a packet to
a blocking port.The idea relies on the assumption that it is better
to discard packets destined to blocking ports, then to let them consume
more and more buffers in the input-port's Rx-counters because eventually
these input ports may become totally blocked. The meanings of the values
are:
other(1) - this entry is currently in use but the conditions under
which it will remain so are different from each of the following
values.
disabled(2) - HOL function disable for device.
enabled(3) - HOL function enable for device.rw Enumeration .1.3.6.1.4.1.171.11.24.1.2.6 |
swDevCtrlAddrLookupModesAndHitRateAccording to the differnet address looke mode setting, to enlarge the
address table size is possible in device. But there is side effect as
the higher level you have, the lower thorughput device has. That means
Level 0 get the smallest table size, but get better performace. We
recommand the user use the Level 1 as defualt setting.rw Enumeration .1.3.6.1.4.1.171.11.24.1.2.7 |
swDevCtrlUploadImageFileNameThe name of the image file to be uploaded from the device to TFTP server
when enabling image upload function (by writing swDevCtrlUploadImage).rw DisplayString .1.3.6.1.4.1.171.11.24.1.2.8 |
swDevCtrlUploadImageImage file upload control. Writing it by any value will
immediately invoke image upload function.rw INTEGER .1.3.6.1.4.1.171.11.24.1.2.9 |
swDevAlarm OBJECT IDENTIFIER .1.3.6.1.4.1.171.11.24.1.3 |
swDevAlarmPartitionDepending on this object, the device send a trap or not when
any one of the device's ports was partitioned.rw Enumeration .1.3.6.1.4.1.171.11.24.1.3.1 |
swDevAlarmNewRootWhen the device has become the new root of the Spanning Tree, this
object decide whether to send a new root trap.rw Enumeration .1.3.6.1.4.1.171.11.24.1.3.2 |
swDevAlarmTopologyChangeThis object determine to send a trap or not when the switch topology
was changed. If the object is enabled(3), the topologyChange trap is
sent by the device when any of its configured ports transitions from
the Learning state to the Forwarding state, or from the Forwarding state
to the Blocking state. For the same port tranition, the device doesn't
send the trap if this object value is disabled or other.rw Enumeration .1.3.6.1.4.1.171.11.24.1.3.3 |
swDevAlarmLinkChangeThis object determine to send a trap or not when the link
was changed. If the object is enabled(3), the Link Change trap is
sent by the device when any of its ports link change. The device doesn't
send the trap if this object value is disabled or other.rw Enumeration .1.3.6.1.4.1.171.11.24.1.3.4 |
swModulePackage OBJECT IDENTIFIER .1.3.6.1.4.1.171.11.24.2 |
swModuleInfoTableA table that contains information about every module. SEQUENCE OF SwModuleInfoEntry .1.3.6.1.4.1.171.11.24.2.1 |
swModuleInfoEntryA list of information for each module of the device. SwModuleInfoEntry .1.3.6.1.4.1.171.11.24.2.1.1 |
swModuleInfoIndexThis object indicates switch module number.(1..swDevInfoMaxNumOfModule)ro INTEGER .1.3.6.1.4.1.171.11.24.2.1.1.1 |
swModuleInfoDescA textual description of the module for memorization .ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.171.11.24.2.1.1.2 |
swModuleInfoTypeThis object indicates the type of this module.ro Enumeration .1.3.6.1.4.1.171.11.24.2.1.1.3 |
swModuleInfoTotalNumOfPortThe number of ports within this module. This value is the sum
of the ports within this module.ro INTEGER .1.3.6.1.4.1.171.11.24.2.1.1.4 |
swModuleInfoNumOfPortInUseThe number of ports in this module connected to the segment or
the end stations.ro INTEGER .1.3.6.1.4.1.171.11.24.2.1.1.5 |
swModuleInfoPortLedStatusThis object is a set of module's port LED indications. Every two bytes are
presented to a port. Except the module 3 (Gigabit module) ,the first byte
is presentd to the Link/Activity LED. The second byte is presented to the
Speed LED. For the module 3 ,the first byte is presentd to the module's
existing LED. The second byte is presented to the Link/Activity LED.
There is one byte per LED.
The most significant bit is used for blink/solid:
Off = The LED is lit permanently.
On = The LED blinks.
The three least significant bits are used for color:
1 = not lit,
2 = green,
3 = yellow,(orange)
4 = blue,
5 = red,
0+6+7 not used
The four remaining bits are currently unused and must be 0.ro OCTET STRING .1.3.6.1.4.1.171.11.24.2.1.1.6 |
swPortPackage OBJECT IDENTIFIER .1.3.6.1.4.1.171.11.24.3 |
swPortInfoTableA table that contains information about every port. SEQUENCE OF SwPortInfoEntry .1.3.6.1.4.1.171.11.24.3.1 |
swPortInfoEntryA list of information for each port of the device. SwPortInfoEntry .1.3.6.1.4.1.171.11.24.3.1.1 |
swPortInfoModuleIndexThis object indicates switch module number.(1..Max module number)ro INTEGER .1.3.6.1.4.1.171.11.24.3.1.1.1 |
swPortInfoPortIndexThis object indicates the module's port number.(1..Max port number in
the module)ro INTEGER .1.3.6.1.4.1.171.11.24.3.1.1.2 |
swPortInfoTypeThis object indicates the connector type of this port.ro Enumeration .1.3.6.1.4.1.171.11.24.3.1.1.3 |
swPortInfoLinkStatusThis object indicates the port link status.ro Enumeration .1.3.6.1.4.1.171.11.24.3.1.1.4 |
swPortInfoNwayStatusThis object indicates the port speed and duplex mode.ro Enumeration .1.3.6.1.4.1.171.11.24.3.1.1.5 |
swPortInfoFlowCtrlStatusThis object indicates the port flow control status.ro Enumeration .1.3.6.1.4.1.171.11.24.3.1.1.6 |
swPortCtrlTableA table that contains control information about every port. SEQUENCE OF SwPortCtrlEntry .1.3.6.1.4.1.171.11.24.3.2 |
swPortCtrlEntryA list of control information for each port of the device. SwPortCtrlEntry .1.3.6.1.4.1.171.11.24.3.2.1 |
swPortCtrlModuleIndexThis object indicates the device module number.(1..Max module number)ro INTEGER .1.3.6.1.4.1.171.11.24.3.2.1.1 |
swPortCtrlPortIndexThis object indicates the module's port number.(1..Max port number in
the module)ro INTEGER .1.3.6.1.4.1.171.11.24.3.2.1.2 |
swPortCtrlAdminStateThis object decide the port enabled or disabled.rw Enumeration .1.3.6.1.4.1.171.11.24.3.2.1.3 |
swPortCtrlLinkStatusAlarmStateDepending on this object to determine to send a trap or
not when link status changes .rw Enumeration .1.3.6.1.4.1.171.11.24.3.2.1.4 |
swPortCtrlNwayStateChose the port speed, duplex mode, and N-Way function mode.rw Enumeration .1.3.6.1.4.1.171.11.24.3.2.1.5 |
swPortCtrlFlowCtrlStateSet IEEE 802.3x compliant flow control function as enabled or disabled.
And IEEE 802.3x compliant flow control function work only when the port
is in full duplex mode.If the port is set Auto-negotiation enabled, the
object stands for flow control capability. The results should be referred
to swPortInfoFlowCtrlStatus object. If the port is in force mode, this
objects is simply used to set the flow control state (on/off). In force
mode, if you change it from enabled to disabled state, it will work after
next system restart. But the flow control changing from disabled to enabled
state, it will immediately work.rw Enumeration .1.3.6.1.4.1.171.11.24.3.2.1.6 |
swPortCtrlBackPressStateDepending on this object determine to enable or disable the
backpressure function when the port is working in half duplex mode.rw Enumeration .1.3.6.1.4.1.171.11.24.3.2.1.7 |
swPortCtrlLockStateThe state of this entry. When the swDevCtrlTableLockState object is
enabled, the state is not changed. When swVlanInfoStatus is in
MAC-Base VLAN mode, this object is always disabled.The meanings of
the values are:
other(1) - this entry is currently in use but the conditions under
which it will remain so are different from each of the
following values.
disable(2) - Port lock funtion disable.
enable(3) - Locking a port. Once the port is locked, it will not
learn new SA addresses, and drop unknown/moved-SA packets
forwarding to/from such ports. This is a way to prevent
undesired traffic from being received or transmmited on
the port. Note that locking a port doesn't lock the MAC
address entries associated with the locked port, i.e. the
existing address entries of the locked port will be age
out even though it is locked.rw Enumeration .1.3.6.1.4.1.171.11.24.3.2.1.8 |
swPortCtrlPriorityThe priority queueing for packets received on this port, except for
BPDU/IGMP packets and packets with unknown unicast destination address.
IGMP and BPDU packets are always routed with high priority; packets with
unknown unicast destination addresses are always routed with low priority.
Other packets follow the rules below:
other(1) - this entry is currently in use but the conditions under
which it will remain so are different from each of the
following values.
default(2) - A packet is normally classified as low priority
,unless at least one of the following is true:
.The packet contained a TAG (per 802.1Q definition) with the
priority greater or equal to 4.
.The address-table entry for the destination address had Pd=HIGH.
force-low_priority(3) - A packet is normally classified as low priority.
force-high_priority(4) - A packet is normally classified as high
priority.rw Enumeration .1.3.6.1.4.1.171.11.24.3.2.1.9 |
swPortCtrlStpStateThe state of STP(spanning tree algorithm) operation on this port. That's
meaning the port whether add in the STP. The value enabled(3) indicates
that STP is enabled on this port, as long as swDevCtrlStpState is also
enabled for this device. When disabled(2) but swDevCtrlStpState is still
enabled for the device, STP is disabled on this port : any BPDU packets
received will be discarded and no BPDU packets will be propagated from
the port. When the device is in 802.1Q Vlan mode, this object will be
enabled and cannot be disabled.rw Enumeration .1.3.6.1.4.1.171.11.24.3.2.1.10 |
swPortCtrlHOLStateThe object provides a way to prevent HOL (Head Of Line) blocking
between ports. HOL protection may prevent forwarding a packet to
a blocking port.The idea relies on the assumption that it is better
to discard packets destined to blocking ports, then to let them consume
more and more buffers in the input-port's Rx-counters because eventually
these input ports may become totally blocked. The value enabled(3)
indicates that HOL function is enabled on this port, as long as
swDevCtrlHOLState is also enabled for this device. When disabled(2) but
swDevCtrlHOLState is still enabled for the device, HOL function is disabled
on this port. The meanings of the values are:
other(1) - this entry is currently in use but the conditions under
which it will remain so are different from each of the following
values.
disabled(2) - HOL function disable.
enabled(3) - HOL function enable.rw Enumeration .1.3.6.1.4.1.171.11.24.3.2.1.11 |
swPortCtrlBroadcastRisingThrThis allows the user to specify the broadcast packets per second.
Broadcast traffic above this rate activates broadcast storm control
(i.e. swPortCtrlBroadcastRisingAct) on the port. The default value
is 500 broadcast packets per second. The setting must be bigger
than the value in swPortCtrlBroadcastFallingThr.rw INTEGER .1.3.6.1.4.1.171.11.24.3.2.1.12 |
swPortCtrlBroadcastFallingThrThis allows the user to specify the broadcast packets per second.
If broadcast traffic is below this rate and rising threshold
condition has been met at least once before this falling threshold
is met, the device will apply the action described in
swPortCtrlBroadcastFallingAct. The default value 250. The setting
must be fewer than the value in swPortCtrlBroadcastRisingThr.rw INTEGER .1.3.6.1.4.1.171.11.24.3.2.1.13 |
swPortCtrlBroadcastRisingActThis object indicates the system action when broadcast storm
rising threshold is met.
other(1) - this entry is currently in use but the conditions under
which it will remain so are different from each of the following
values.
do-nothing(2) - no action.
blocking(3) - the port can discard any coming broadcast frame.
blocking-trap(4) - the port can discard any coming broadcast frame. And
the device can send a broadcast rising trap.rw Enumeration .1.3.6.1.4.1.171.11.24.3.2.1.14 |
swPortCtrlBroadcastFallingActThis object indicates the device action when broadcast storm
falling threshold is met.
other(1) - this entry is currently in use but the conditions under
which it will remain so are different from each of the following
values.
do-nothing(2) - no action.
forwarding(3) - the port has returned to normal operation mode.
forwarding-trap(4) - the port has returned to normal operation mode. And
the device can send a broadcast falling trap.rw Enumeration .1.3.6.1.4.1.171.11.24.3.2.1.15 |
swPortCtrlCleanAllStatisticCounterSetting this object will reset current device's all statistic counters.rw INTEGER .1.3.6.1.4.1.171.11.24.3.2.1.16 |
swPortStTableA list of port statistic Counter entries. SEQUENCE OF SwPortStEntry .1.3.6.1.4.1.171.11.24.3.3 |
swPortStEntryThis entry include all the port statistic Counter which support
by the device, like Bytes received, Bytes Sent ... SwPortStEntry .1.3.6.1.4.1.171.11.24.3.3.1 |
swPortStModuleIndexThis object indicates the device module number.(1..Max module number)ro INTEGER .1.3.6.1.4.1.171.11.24.3.3.1.1 |
swPortStPortIndexThis object indicates the module's port number.(1..Max port number in
the module)ro INTEGER .1.3.6.1.4.1.171.11.24.3.3.1.2 |
swPortStByteRxswDevCtrlCounterMode = 2(switched-frames):This counter is incre-
mented once for every data octet of good packets(unicast + multi-
cast + broadcast) received.
swDevCtrlCounterMode = 3(all-frames):This counter is incremented
once for every data octet of good packets(unicast + multicast +
broadcast packets) and for local and dropped packets.ro Counter .1.3.6.1.4.1.171.11.24.3.3.1.3 |
swPortStByteTxThis counter is incremented once for every data octet of a trans-
mitted good packet.ro Counter .1.3.6.1.4.1.171.11.24.3.3.1.4 |
swPortStFrameRxswDevCtrlCounterMode = 2(switched-frames):This counter is incre-
mented once for every good packet(unicast + multicast + broadcast
) received.
swDevCtrlCounterMode = 3(all-frames):This counter is incremented
once for every good packet(unicast + multicast + broadcast packets)
and for local and dropped packets received.ro Counter .1.3.6.1.4.1.171.11.24.3.3.1.5 |
swPortStFrameTxThis counter is incremented once for every transmitted good packet.ro Counter .1.3.6.1.4.1.171.11.24.3.3.1.6 |
swPortStTotalBytesRxThis counter is incremented once for every data octet of all
received packets. This include data octets of rejected and local
packets which are not forwarded to the switching core for trans-
mission. This counter should reflect all the data octets received
on the line. Note: A nibble is not counted as a whole byte.ro Counter .1.3.6.1.4.1.171.11.24.3.3.1.7 |
swPortStTotalFramesRxThis counter is incremented once for every received packets. This
include rejected and local packets which are not forwarded to the
switching core for transmission. This counter should reflect all
packets received on the line.ro Counter .1.3.6.1.4.1.171.11.24.3.3.1.8 |
swPortStBroadcastFramesRxswDevCtrlCounterMode = 2(switched-frames):This counter is incre-
mented once for every good broadcast packet received.
swDevCtrlCounterMode = 3(all-frames):This counter is incremented
once for every good broadcast packet received and for local and
dropped broadcast packets.ro Counter .1.3.6.1.4.1.171.11.24.3.3.1.9 |
swPortStMulticastFramesRxswDevCtrlCounterMode = 2(switched-frames):This counter is incre-
mented once for every good multicast packet received.
swDevCtrlCounterMode = 3(all-frames):This counter is incremented
once for every good multicast packet received and for local and
dropped multicast packets. This counter does not include broad-
cast packets.ro Counter .1.3.6.1.4.1.171.11.24.3.3.1.10 |
swPortStCRCErrorThis counter is incremented once for every received packet which
meets all the following conditions:
1.Packet data length is between 64 and 1518 bytes inclusive.
2.Packet has invalid CRC.
3.Collision event , late collision event and receive error event
have not been detected.ro Counter .1.3.6.1.4.1.171.11.24.3.3.1.11 |
swPortStOversizeFramesThe number of good frames with length more than 1518 bytes.ro Counter .1.3.6.1.4.1.171.11.24.3.3.1.12 |
swPortStFragmentsThis counter is incremented once for every received packet which
meets all the following conditions:
1.Packet data length is less than 64 bytes or packet withourt SFD
and is less than 64 bytes in length.
2.Packet has invalid CRC.
3.Collision event , late collision event and receive error event
have not been detected.ro Counter .1.3.6.1.4.1.171.11.24.3.3.1.13 |
swPortStJabberThe number of frames with length more than 1518 bytes and with
CRC error or misaligned.ro Counter .1.3.6.1.4.1.171.11.24.3.3.1.14 |
swPortStCollisionThe number of Collisionsro Counter .1.3.6.1.4.1.171.11.24.3.3.1.15 |
swPortStLateCollisionThe number of Late Collision(collision occurring later than
576th transmitted bit).ro Counter .1.3.6.1.4.1.171.11.24.3.3.1.16 |
swPortStFrames-64-bytesThis counter is incremented once for every received and trans-
mitted packet with size of 64 bytes. This counter includes reject-
ed received and transmitted packets.ro Counter .1.3.6.1.4.1.171.11.24.3.3.1.17 |
swPortStFrames-65-127-bytesThis counter is incremented once for every received and trans-
mitted packet with size of 65 to 127 bytes. This counter includes
rejected received and transmitted packets.ro Counter .1.3.6.1.4.1.171.11.24.3.3.1.18 |
swPortStFrames-128-255-bytesThis counter is incremented once for every received and trans-
mitted packet with size of 128 to 255 bytes. This counter includes
rejected received and transmitted packets.ro Counter .1.3.6.1.4.1.171.11.24.3.3.1.19 |
swPortStFrames-256-511-bytesThis counter is incremented once for every received and trans-
mitted packet with size of 256 to 511 bytes. This counter includes
rejected received and transmitted packets.ro Counter .1.3.6.1.4.1.171.11.24.3.3.1.20 |
swPortStFrames-512-1023-bytesThis counter is incremented once for every received and trans-
mitted packet with size of 512 to 1023 bytes. This counter includ-
es rejected received and transmitted packets.ro Counter .1.3.6.1.4.1.171.11.24.3.3.1.21 |
swPortStFrames-1024-1536-bytesThis counter is incremented once for every received and trans-
mitted packet with size of 1024 to 1536 bytes. This counter includ-
es rejected received and transmitted packets.ro Counter .1.3.6.1.4.1.171.11.24.3.3.1.22 |
swPortStFramesDroppedFramesThis counter is incremented once for every received dropped pack-
et.ro Counter .1.3.6.1.4.1.171.11.24.3.3.1.23 |
swPortStMulticastFramesTxThe number of multicast frames sent. This counter does not include
broadcast packets.ro Counter .1.3.6.1.4.1.171.11.24.3.3.1.24 |
swPortStBroadcastFramesTxThe number of broadcast frames sent.ro Counter .1.3.6.1.4.1.171.11.24.3.3.1.25 |
swPortStUndersizeFramesThis counter is incremented once for every received packet which
meets all the following conditions:
1.Packet data length is less than 64 bytes.
2.Packet has valid CRC.
3.Collision event , late collision event and receive error event
have not been detected.ro Counter .1.3.6.1.4.1.171.11.24.3.3.1.26 |
swFdbPackage OBJECT IDENTIFIER .1.3.6.1.4.1.171.11.24.4 |
swFdbStaticTableLike typical legacy bridge devices, FDB table records the mapping
of Source MAC Address and its associated source port, and forward
incoming packets to its destination port according to the Destination
MAC Address of the packet as well as the MAC-port pair entries of the
FDB table. Note that the priority of FDB table entries is lower than
Filtering Table, i.e. if there is a table hash collision between the
entries of FDB Table and Filtering Table inside the switch H/W address
table, then Filtering Table entry overwrite the colliding entry of
FDB Table. See swFdbFilterTable description also. SEQUENCE OF SwFdbStaticEntry .1.3.6.1.4.1.171.11.24.4.1 |
swFdbStaticEntryA list of information specifies which ports the frames with specific
destination MAC address to go. SwFdbStaticEntry .1.3.6.1.4.1.171.11.24.4.1.1 |
swFdbStaticVidThis object indicates the VLAN-ID. If VLAN is in mac-based
mode or disabled, the object indicates the default VLAN-ID (0).ro INTEGER .1.3.6.1.4.1.171.11.24.4.1.1.1 |
swFdbStaticAddressIndexThe destination MAC address in a frame to which this entry's
forwarding information applies. This object can take the value of
an unicast address or the multicast address.ro MacAddress (SNMPv2-TC) .1.3.6.1.4.1.171.11.24.4.1.1.2 |
swFdbStaticPortMapThe set of ports to which frames received from a specific port
and destined for a specific MAC address, are allowed to be
forwarded. Each octet within the value of this object specifies
a set of eight ports, with the first octet specifying ports 1
through 8, the second octet specifying ports 9 through 16, etc.
Within each octet, the most significant bit represents the lowest
numbered port, and the least significant bit represents the highest
numbered port. Thus, each port of the bridge is represented by
a single bit within the value of this object. If that bit has a
value of '1' then that port is included in the set of ports; the
port is not included if its bit has a value of '0'.(Note that the
setting of the bit corresponding to the port from which a frame
is received is irrelevant.). In module 1 (base module), there are
22 100M twisted-pair ports (port 1..22) which is mapped to the PortMap's
port 1 to 22 respectively. In module 2 (slot 1 module), there are 2 100M
FX/100 TX (or a single port 100M FX) ports which is mapped to the
PortMap's port 23, 24 respectively (if the module is a single port 100M FX
, it is just mapped to port 23 and port 24 is ignored). Module 3 (slot 2
module) is a single-port Gigabit Ethernet and it is mapped to the PortMap's
port 25.rw OCTET STRING .1.3.6.1.4.1.171.11.24.4.1.1.3 |
swFdbStaticStateThis object indicates the status of this entry.
other(1) - this entry is currently in use but the conditions under
which it will remain so are different from each of the following
values.
invalid(2) - writing this value to the object, and then the corresponding
entry will be removed from the table.
valid(3) - this entry is reside in the table.rw Enumeration .1.3.6.1.4.1.171.11.24.4.1.1.4 |
swFdbStaticStatusThis object indicates the status of this entry.
other(1) - this entry is currently in use but the conditions under
which it will remain so are different from each of the following
values.
apply(2) - this entry is currently in use and reside in the table.
not-apply(3) - this entry is reside in the table but currently not
in use due to conflict with filter table.ro Enumeration .1.3.6.1.4.1.171.11.24.4.1.1.5 |
swFdbFilterTableA table which contains the filtering information of the
unicast/multicast entries. This table is used by the transparent
switching function in determining how to filter the received frames.
The Filtering Table entries' priority overrides Static FDB Table
as well as IGMP table entries, say, if there is a hash table entry
collision between Filtering Table and Static FDB Table setting in
the switch device's H/W address table, then Filter Table entry setting
overwrites the colliding entry in Static FDB Table. See swFdbStaticTable
description also. SEQUENCE OF SwFdbFilterEntry .1.3.6.1.4.1.171.11.24.4.2 |
swFdbFilterEntryA list of information about a specific unicast/multicast MAC address
for which the switch has filtering information. SwFdbFilterEntry .1.3.6.1.4.1.171.11.24.4.2.1 |
swFdbFilterVidThis object indicates the VLAN-ID. If VLAN is in mac-based
mode or disabled, the object indicates the default VLAN-ID (0).ro INTEGER .1.3.6.1.4.1.171.11.24.4.2.1.1 |
swFdbFilterAddressIndexThis object indicates a unicast/multicast MAC address for which the bridge
has filtering information.ro MacAddress (SNMPv2-TC) .1.3.6.1.4.1.171.11.24.4.2.1.2 |
swFdbFilterStateThis object indicates the status of this entry.
other(1) - this entry is currently in use but the conditions under
which it will remain so are different from each of the following
values.
dst-src-addr(2) - recieved frames's destination address or source
address are currently used to be filtered as it meets with
the MAC address entry of the table.
invalid(3) - writing this value to the object, and then the corresponding
entry will be removed from the table.rw Enumeration .1.3.6.1.4.1.171.11.24.4.2.1.3 |