DES3200-52P-L3MGMT-MIB
The Structure of Layer 3 Network Management Information for the proprietary enterprise.
Main OID:
swL3MgmtMIB.1.3.6.1.4.1.171.11.113.10.1.3
277
Objects
Active
Status
5
Dependencies
Imported Objects
Objects
277 total| Object Name |
|---|
swL3MgmtMIBThe Structure of Layer 3 Network Management Information for the
proprietary enterprise. MODULE-IDENTITY .1.3.6.1.4.1.171.11.113.10.1.3 |
swL3DevMgmt OBJECT IDENTIFIER .1.3.6.1.4.1.171.11.113.10.1.3.1 |
swL3DevCtrl OBJECT IDENTIFIER .1.3.6.1.4.1.171.11.113.10.1.3.1.1 |
swL3DevCtrlRIPStateThis object indicates Routing Information Protocol (RIP)
version 2 function is enabled or disabled.rw Enumeration .1.3.6.1.4.1.171.11.113.10.1.3.1.1.1 |
swL3DevCtrlOSPFStateThis object indicates OSPF protocol is enabled or disabled.rw Enumeration .1.3.6.1.4.1.171.11.113.10.1.3.1.1.2 |
swL3DevCtrlDVMRPStateThis object indicates DVMRP protocol is enabled or disabled.rw Enumeration .1.3.6.1.4.1.171.11.113.10.1.3.1.1.3 |
swL3DevCtrlVRRPStateThis object indicates VRRP protocol is enabled or disabled.rw Enumeration .1.3.6.1.4.1.171.11.113.10.1.3.1.1.5 |
swL3DevCtrlVrrpPingStateThis object indicates VRRP protocol Ping is enabled or disabled.rw Enumeration .1.3.6.1.4.1.171.11.113.10.1.3.1.1.6 |
swL3DevCtrlDHCPAutoConfigStateThis object indicates auto config is enabled or disabled.rw Enumeration .1.3.6.1.4.1.171.11.113.10.1.3.1.1.7 |
swL3IpMgmt OBJECT IDENTIFIER .1.3.6.1.4.1.171.11.113.10.1.3.2 |
swL3IpCtrlMgmt OBJECT IDENTIFIER .1.3.6.1.4.1.171.11.113.10.1.3.2.1 |
swL3IpCtrlTableThis table contains IP interface information. SEQUENCE OF SwL3IpCtrlEntry .1.3.6.1.4.1.171.11.113.10.1.3.2.1.3 |
swL3IpCtrlEntryA list of information about a specific IP interface. SwL3IpCtrlEntry .1.3.6.1.4.1.171.11.113.10.1.3.2.1.3.1 |
swL3IpCtrlInterfaceNameThis object indicates the name of the IP interface.ro DisplayString .1.3.6.1.4.1.171.11.113.10.1.3.2.1.3.1.1 |
swL3IpCtrlIfIndexThis object uniquely identifies the IP interface number in the
swL3IpCtrlTable.ro INTEGER .1.3.6.1.4.1.171.11.113.10.1.3.2.1.3.1.2 |
swL3IpCtrlIpAddrThe IP address of the interface. This object only can take the
value of the unicast IP address.rw IpAddress .1.3.6.1.4.1.171.11.113.10.1.3.2.1.3.1.3 |
swL3IpCtrlIpSubnetMaskThe IP net mask for this interface.rw IpAddress .1.3.6.1.4.1.171.11.113.10.1.3.2.1.3.1.4 |
swL3IpCtrlVlanNameThis object indicates the IP control entry's VLAN name. The
VLAN name in each entry must be unique in the IP Control Table.rw DisplayString .1.3.6.1.4.1.171.11.113.10.1.3.2.1.3.1.5 |
swL3IpCtrlProxyArpThis object indicates enable/disable of the proxy ARP function for IPv4.rw Enumeration .1.3.6.1.4.1.171.11.113.10.1.3.2.1.3.1.6 |
swL3IpCtrlSecondaryWhen this is true(1), the IP address is the secondary IP. When
false(2), the IP address is the primary IP.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.171.11.113.10.1.3.2.1.3.1.7 |
swL3IpCtrlModeThis object indicates the IP operation mode.
other(1) - This entry is currently in use but the conditions under
which it will remain are determined by each of the following values.
bootp(3) - The IP address will be set automatically from a BOOTP
server.
dhcp(4) - The IP address will be set automatically from a DHCP
server.rw Enumeration .1.3.6.1.4.1.171.11.113.10.1.3.2.1.3.1.8 |
swL3IpCtrlAdminStateThe state of the IP interface.rw Enumeration .1.3.6.1.4.1.171.11.113.10.1.3.2.1.3.1.9 |
swL3IpCtrlIpv4AdminStateThe IPv4 admin state of the IP interface. The default state is determined by project.
This state will only be effective when the swL3IpCtrlAdminState is enabled.rw Enumeration .1.3.6.1.4.1.171.11.113.10.1.3.2.1.3.1.10 |
swL3IpCtrlIpv6AdminStateThe IPv6 admin state of the IP interface. The default state is determined by project.
This state will only be effective when the swL3IpCtrlAdminState is enabled.rw Enumeration .1.3.6.1.4.1.171.11.113.10.1.3.2.1.3.1.12 |
swL3IpCtrlIpv6LinkLocalAddressThe IPv6 link local address for this interface.ro Ipv6Address .1.3.6.1.4.1.171.11.113.10.1.3.2.1.3.1.14 |
swL3IpCtrlIpv6LinkLocalPrefixLenThe IPv6 prefix length for this IPv6 link local address.ro INTEGER .1.3.6.1.4.1.171.11.113.10.1.3.2.1.3.1.15 |
swL3IpCtrlStateThis variable displays the status of the entry. The status is used
for creating, modifying, and deleting instances of the objects
in this table.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.171.11.113.10.1.3.2.1.3.1.16 |
swL3IpCtrlIpv6LinkLocalAutoStateThe state of the IPv6 link local auto.rw Enumeration .1.3.6.1.4.1.171.11.113.10.1.3.2.1.3.1.17 |
swL3IpCtrlLocalProxyArpThis object indicates enable/disable of the local proxy ARP function for IPv4.rw Enumeration .1.3.6.1.4.1.171.11.113.10.1.3.2.1.3.1.18 |
swL3IpCtrlDhcpv6ClientStateThe object indicates the state of the DHCPv6 client.rw Enumeration .1.3.6.1.4.1.171.11.113.10.1.3.2.1.3.1.20 |
swL3IpCtrlIpDirectedBroadcastStateThe object indicates the state of the IP Directed Broadcast.rw Enumeration .1.3.6.1.4.1.171.11.113.10.1.3.2.1.3.1.21 |
swL3IpCtrlIpDhcpOption12StateEnable or disable insertion of option 12 in the DHCPDISCOVER and
DHCPREQUEST message.rw Enumeration .1.3.6.1.4.1.171.11.113.10.1.3.2.1.3.1.22 |
swL3IpCtrlIpDhcpOption12HostNameSpecify the host name to be inserted in the DHCPDISCOVER and
DHCPREQUEST message. The specified host name must start with a
letter, end with a letter or digit, and have only letters, digits,
and hyphen as interior characters; the maximal length is 63. By
default, the host name is empty.
When set an empty host name, means to clear the host name setting and
use the default value to encode option 12.rw DisplayString .1.3.6.1.4.1.171.11.113.10.1.3.2.1.3.1.23 |
swL3Ipv6CtrlTableThis table contains IPv6 information of an IP interface. SEQUENCE OF SwL3Ipv6CtrlEntry .1.3.6.1.4.1.171.11.113.10.1.3.2.1.4 |
swL3Ipv6CtrlEntryA list of IPv6 information about a specific IP interface. SwL3Ipv6CtrlEntry .1.3.6.1.4.1.171.11.113.10.1.3.2.1.4.1 |
swL3Ipv6CtrlInterfaceNameThis object indicates the name of the IP interface.ro DisplayString .1.3.6.1.4.1.171.11.113.10.1.3.2.1.4.1.1 |
swL3Ipv6CtrlMaxReassmblySizeMaximum Reassembly Size of the IP interface.ro INTEGER .1.3.6.1.4.1.171.11.113.10.1.3.2.1.4.1.2 |
swL3Ipv6CtrlNsRetransTimerNeighbor solicitation's retransmit timer.
The unit is set in milliseconds.rw Unsigned32 .1.3.6.1.4.1.171.11.113.10.1.3.2.1.4.1.3 |
swL3Ipv6CtrlRaStateNeighbor solicited state.rw Enumeration .1.3.6.1.4.1.171.11.113.10.1.3.2.1.4.1.5 |
swL3Ipv6CtrlRaMinRtrAdvIntervalThe minimum time allowed between sending unsolicited multicast Router
Advertisements from the interface. The unit is set in seconds.
It must be no less than 3 seconds and no greater than .75 * MaxRtrAdvInterval.
Default value: 0.33 * MaxRtrAdvIntervalrw INTEGER .1.3.6.1.4.1.171.11.113.10.1.3.2.1.4.1.6 |
swL3Ipv6CtrlRaMaxRtrAdvIntervalThe maximum time allowed between sending unsolicited multicast Router
Advertisements from the interface. The unit is set in seconds.rw INTEGER .1.3.6.1.4.1.171.11.113.10.1.3.2.1.4.1.7 |
swL3Ipv6CtrlRaLifeTimeIndicates the lifetime of the router as the default router.rw INTEGER .1.3.6.1.4.1.171.11.113.10.1.3.2.1.4.1.8 |
swL3Ipv6CtrlRaReachableTimeIndicates the amount of time that a node can consider a neighboring
node reachable after receiving a reachability confirmation.rw INTEGER .1.3.6.1.4.1.171.11.113.10.1.3.2.1.4.1.9 |
swL3Ipv6CtrlRaRetransTimeIndicates the amount of time between retransmissions of neighbor
solicited messages.
The unit is set in millisecond.rw Unsigned32 .1.3.6.1.4.1.171.11.113.10.1.3.2.1.4.1.10 |
swL3Ipv6CtrlRaHopLimitIndicates the default value of the hop limit field in the IPv6 header for
packets sent by hosts that receive this RA message.rw INTEGER .1.3.6.1.4.1.171.11.113.10.1.3.2.1.4.1.11 |
swL3Ipv6CtrlRaManagedFlagWhen enabled, it indicates that hosts receiving this RA must use a
stateful address configuration protocol to obtain an address in the addition
to the addresses derived from the stateless address configuration.rw Enumeration .1.3.6.1.4.1.171.11.113.10.1.3.2.1.4.1.12 |
swL3Ipv6CtrlRaOtherConfigFlagWhen enabled, it indicates that hosts receiving this RA must use a stateful
address configuration protocol to obtain an on-link address configuration information.rw Enumeration .1.3.6.1.4.1.171.11.113.10.1.3.2.1.4.1.13 |
swL3Ipv6AddressCtrlTableThis table contains IPv6 address information for each IP interface. SEQUENCE OF SwL3Ipv6AddressCtrlEntry .1.3.6.1.4.1.171.11.113.10.1.3.2.1.5 |
swL3Ipv6AddressCtrlEntryA list of information about a specific IPv6 address. SwL3Ipv6AddressCtrlEntry .1.3.6.1.4.1.171.11.113.10.1.3.2.1.5.1 |
swL3Ipv6AddressCtrlInterfaceNameThis object indicates the name of the IP interface.ro DisplayString .1.3.6.1.4.1.171.11.113.10.1.3.2.1.5.1.1 |
swL3Ipv6AddressSpecify the IPv6 address.ro Ipv6Address .1.3.6.1.4.1.171.11.113.10.1.3.2.1.5.1.2 |
swL3Ipv6AddressCtrlPrefixLenIndicates the prefix length of this IPv6 address.ro INTEGER .1.3.6.1.4.1.171.11.113.10.1.3.2.1.5.1.3 |
swL3Ipv6AddressCtrlPreferredLifeTimeIndicates the number of seconds that an address, based on the specified prefix,
using the stateless address configuration, remains in preferred state.
For an infinite valid lifetime, the value can be set to 0xffffffff.rw Unsigned32 .1.3.6.1.4.1.171.11.113.10.1.3.2.1.5.1.4 |
swL3Ipv6AddressCtrlValidLifeTimeIndicates the number of seconds that an address, based on the specified prefix,
using the stateless address configuration, remains valid.
For an infinite valid lifetime, the value can be set to 0xffffffff.rw Unsigned32 .1.3.6.1.4.1.171.11.113.10.1.3.2.1.5.1.5 |
swL3Ipv6AddressCtrlOnLinkFlagWhen enabled, the address implied by the specified prefix is available
on the link where the RA message is received.rw Enumeration .1.3.6.1.4.1.171.11.113.10.1.3.2.1.5.1.6 |
swL3Ipv6AddressCtrlAutonomousFlagWhen enabled, the specified prefix will be used to create an autonomous address configuration.rw Enumeration .1.3.6.1.4.1.171.11.113.10.1.3.2.1.5.1.7 |
swL3Ipv6AddressCtrlStateThis variable displays the status of the entry. The status is used
for creating, modifying, and deleting instances of the objects
in this table.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.171.11.113.10.1.3.2.1.5.1.8 |
swL3Ipv6AddressCtrlAddressTypeThis object indicates the type of the IPv6 address.
manual(1): the IPv6 address is configured by user.
dhcpv6(2): the IPv6 address is assigned by DHCPv6 server.
stateless(3): the IPv6 address is assigned by router advertisement.ro Enumeration .1.3.6.1.4.1.171.11.113.10.1.3.2.1.5.1.9 |
swL3IpCtrlAllIpIfStateThis object indicates all interface function state of the device.
(except the loopback interface)rw Enumeration .1.3.6.1.4.1.171.11.113.10.1.3.2.1.7 |
swL3LoopBackIpCtrlTableThis table contains loopback IP interface information. SEQUENCE OF SwL3LoopBackIpCtrlEntry .1.3.6.1.4.1.171.11.113.10.1.3.2.1.8 |
swL3LoopBackIpCtrlEntryA list of information about a specific loopback IP interface. SwL3LoopBackIpCtrlEntry .1.3.6.1.4.1.171.11.113.10.1.3.2.1.8.1 |
swL3LoopBackIpCtrlInterfaceNameThis object indicates the name of the loopback IP interface.ro DisplayString .1.3.6.1.4.1.171.11.113.10.1.3.2.1.8.1.1 |
swL3LoopBackIpCtrlIfIndexThis object uniquely identifies the loopback IP interface number in the
swL3LoopBackIpCtrlTable.ro INTEGER .1.3.6.1.4.1.171.11.113.10.1.3.2.1.8.1.2 |
swL3LoopBackIpCtrlIpAddrThe IP address of the loopback interface. This object only can take the
value of the unicast IP address.rw IpAddress .1.3.6.1.4.1.171.11.113.10.1.3.2.1.8.1.3 |
swL3LoopBackIpCtrlIpSubnetMaskThe IP net mask for this loopback interface.rw IpAddress .1.3.6.1.4.1.171.11.113.10.1.3.2.1.8.1.4 |
swL3LoopBackIpCtrlAdminStateThe state of the loopback IP interface.rw Enumeration .1.3.6.1.4.1.171.11.113.10.1.3.2.1.8.1.5 |
swL3LoopBackIpCtrlRowStatusThis variable displays the status of the entry. The status is used
for creating, modifying, and deleting instances of the objects
in this table.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.171.11.113.10.1.3.2.1.8.1.6 |
swL3IpFdbMgmt OBJECT IDENTIFIER .1.3.6.1.4.1.171.11.113.10.1.3.2.2 |
swL3IpFdbInfoTableA table that contains forwarding and/or filtering information.
This information is used by the switch in determining how to
propagate the received IP packets. SEQUENCE OF SwL3IpFdbInfoEntry .1.3.6.1.4.1.171.11.113.10.1.3.2.2.1 |
swL3IpFdbInfoEntryInformation about a specific IP address for which the bridge
has some forwarding and/or filtering information. SwL3IpFdbInfoEntry .1.3.6.1.4.1.171.11.113.10.1.3.2.2.1.1 |
swL3IpFdbInfoIpAddrA IP address for which switch has forwarding and/or filtering
information.ro IpAddress .1.3.6.1.4.1.171.11.113.10.1.3.2.2.1.1.1 |
swL3IpFdbInfoIpSubnetMaskA IP net mask for this interface for which the switch has
forwarding and/or filtering information.ro IpAddress .1.3.6.1.4.1.171.11.113.10.1.3.2.2.1.1.2 |
swL3IpFdbInfoPortEither the value '0', or the port number of the port on which
packet having a IP address equal to the value of the
corresponding instance of swL3IpFdbInfoIpAddr has been seen. A
value of '0' indicates that the port number has not been learned
but that switch does have some forwarding/filtering information
about this address.ro INTEGER .1.3.6.1.4.1.171.11.113.10.1.3.2.2.1.1.3 |
swL3IpFdbInfoTypeThe status of this entry.ro Enumeration .1.3.6.1.4.1.171.11.113.10.1.3.2.2.1.1.4 |
swL3IpArpAgingTimeThe timeout period in minutes for aging out dynamically learned
ARP information.rw INTEGER .1.3.6.1.4.1.171.11.113.10.1.3.2.4 |
swL3IpStaticRouteTableThis entity's IP static Routing table. SEQUENCE OF SwL3IpStaticRouteEntry .1.3.6.1.4.1.171.11.113.10.1.3.2.5 |
swL3IpStaticRouteEntryA particular route to a particular destination, under a particular policy.
Once an entry is built,it shouldn't be modified.That is,it just supports
create and delete actions. SwL3IpStaticRouteEntry .1.3.6.1.4.1.171.11.113.10.1.3.2.5.1 |
swL3IpStaticRouteDestThe destination IP address of this route.
This object may not take a Multicast (Class D)
address value.
Any assignment (implicit or otherwise) of an
instance of this object to a value x must be
rejected if the bitwise logical-AND of x with
the value of the corresponding instance of the
swL3IpStaticRouteMask object is not equal to x.ro IpAddress .1.3.6.1.4.1.171.11.113.10.1.3.2.5.1.1 |
swL3IpStaticRouteMaskIndicate the mask to be logical-AND with the
destination address before being compared to
the value in the swL3IpStaticRouteDest field.
For those systems that do not support arbitrary
subnet masks, an agent constructs the value of
the swL3IpStaticRouteMask by reference to the IP
Address Class.
Any assignment (implicit or otherwise) of an
instance of this object to a value x must be
rejected if the bitwise logical-AND of x with
the value of the corresponding instance of the
swL3IpStaticRouteDest object is not equal to
swL3IpStaticRouteDest.ro IpAddress .1.3.6.1.4.1.171.11.113.10.1.3.2.5.1.2 |
swL3IpStaticRouteBkupStateThe routing state for this route.The value SHOULD be
primary(1), backup(2) or none(3).rw Enumeration .1.3.6.1.4.1.171.11.113.10.1.3.2.5.1.3 |
swL3IpStaticRouteNextHopSpecifies the IP address for the next hop router.
An IP address of 255.255.255.255 denotes a Null interface
as the next hop.ro IpAddress .1.3.6.1.4.1.171.11.113.10.1.3.2.5.1.4 |
swL3IpStaticRouteMetricSpecifies the routing metric for this route.rw INTEGER .1.3.6.1.4.1.171.11.113.10.1.3.2.5.1.5 |
swL3IpStaticRouteStatusThis object indicates the status of this entry.
other(1) - this entry is currently in use but the conditions
under which it will remain so are different from each of
the following values.
invalid(2) - writing this value to the object, and then the
corresponding entry will be removed from the table.
valid(3) - this entry resides in the table.
active(4) - the nextHop of this entry exists in the ARP table.
inActive(5) - the next hop of this entry does not exist in the
ARP table.rw Enumeration .1.3.6.1.4.1.171.11.113.10.1.3.2.5.1.6 |
swL3IpStaticRouteWeightSpecifies the weight value. Used for the weighted multipath.rw INTEGER .1.3.6.1.4.1.171.11.113.10.1.3.2.5.1.7 |
swL3IpStaticRouteInterfaceNameSpecifies the name of the IP interface.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.171.11.113.10.1.3.2.5.1.8 |
swL3IpStaticRouteCostSpecifies the cost of the Route Entry.ro INTEGER .1.3.6.1.4.1.171.11.113.10.1.3.2.5.1.9 |
swL3RelayMgmt OBJECT IDENTIFIER .1.3.6.1.4.1.171.11.113.10.1.3.3 |
swL3RelayDhcpMgmt OBJECT IDENTIFIER .1.3.6.1.4.1.171.11.113.10.1.3.3.1 |
swL3RelayDhcpStateThis object indicates if the DHCP Relay function is enabled or
disabled.rw Enumeration .1.3.6.1.4.1.171.11.113.10.1.3.3.1.1 |
swL3RelayDhcpHopCountThis object indicates the maximum number of router hops that
the BOOTP packets can cross.rw INTEGER .1.3.6.1.4.1.171.11.113.10.1.3.3.1.2 |
swL3RelayDhcpTimeThresholdThis object indicates the minimum time in seconds within which
the switch must relay the DHCP request. If this time is
exceeded, the switch will drop the DHCP packet.rw INTEGER .1.3.6.1.4.1.171.11.113.10.1.3.3.1.3 |
swL3RelayDhcpCtrlTableThis table specifies the IP address as a destination to forward
(relay) DHCP packets to. SEQUENCE OF SwL3RelayDhcpCtrlEntry .1.3.6.1.4.1.171.11.113.10.1.3.3.1.4 |
swL3RelayDhcpCtrlEntryA list of information specifying the IP address as a destination
to forward (relay) DHCP packets to. SwL3RelayDhcpCtrlEntry .1.3.6.1.4.1.171.11.113.10.1.3.3.1.4.1 |
swL3RelayDhcpCtrlInterfaceNameThe name of the IP interface.ro DisplayString .1.3.6.1.4.1.171.11.113.10.1.3.3.1.4.1.1 |
swL3RelayDhcpCtrlServerThe DHCP server IP address.ro IpAddress .1.3.6.1.4.1.171.11.113.10.1.3.3.1.4.1.2 |
swL3RelayDhcpCtrlStateThis object indicates the status of this entry.
other(1) - this entry is currently in use but the conditions
under which it will remain so are different from each of
the following values.
invalid(2) - writing this value to the object, and then the
corresponding entry will be removed from the table.
valid(3) - this entry is reside in the table.rw Enumeration .1.3.6.1.4.1.171.11.113.10.1.3.3.1.4.1.3 |
swL3RelayDhcpOption82StateThis object indicates DHCP Relay Option 82 function is enabled or
disabled.rw Enumeration .1.3.6.1.4.1.171.11.113.10.1.3.3.1.5 |
swL3RelayDhcpOption82CheckStateThis object indicates DHCP Relay Option 82 Check function is enabled or
disabled.rw Enumeration .1.3.6.1.4.1.171.11.113.10.1.3.3.1.6 |
swL3RelayDhcpOption82PolicyThis object indicates DHCP Relay Option 82 Policy.rw Enumeration .1.3.6.1.4.1.171.11.113.10.1.3.3.1.7 |
swL3DHCPRelayOption60 OBJECT IDENTIFIER .1.3.6.1.4.1.171.11.113.10.1.3.3.1.8 |
swL3DHCPRelayOption60StateThis object indicates DHCP relay option 60 function is enabled or
disabled.rw Enumeration .1.3.6.1.4.1.171.11.113.10.1.3.3.1.8.1 |
swL3DHCPRelayOption60DefModeThis object indicates default mode that has no option 60 mathcing rules.
relay(1): means to relay the packet to the IP address which is specified
by swL3DHCPRelayOption60DefRelayIp.
drop(2): means to drop the packet.rw Enumeration .1.3.6.1.4.1.171.11.113.10.1.3.3.1.8.2 |
swL3DHCPRelayOption60DefTableThis table indicates the default relay servers for the packet
that has no option 60 mathcing rules. SEQUENCE OF SwL3DHCPRelayOption60DefEntry .1.3.6.1.4.1.171.11.113.10.1.3.3.1.8.3 |
swL3DHCPRelayOption60DefEntryA list of information indicates the default relay servers for the packet
that has no option 60 mathcing rules. SwL3DHCPRelayOption60DefEntry .1.3.6.1.4.1.171.11.113.10.1.3.3.1.8.3.1 |
swL3DHCPRelayOption60DefRelayIpThis object indicates the IP address of default relay server.ro IpAddress .1.3.6.1.4.1.171.11.113.10.1.3.3.1.8.3.1.1 |
swL3DHCPRelayOption60DefRowStatusThis object indicates the status of this entry.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.171.11.113.10.1.3.3.1.8.3.1.2 |
swL3DHCPRelayOption60TableThis table indicates the relay servers for the packet at option 60 rules. SEQUENCE OF SwL3DHCPRelayOption60Entry .1.3.6.1.4.1.171.11.113.10.1.3.3.1.8.4 |
swL3DHCPRelayOption60EntryA list of information indicates the relay servers for the packet
at option 60 rules. SwL3DHCPRelayOption60Entry .1.3.6.1.4.1.171.11.113.10.1.3.3.1.8.4.1 |
swL3DHCPRelayOption60StringThis object indicates string of this entry.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.171.11.113.10.1.3.3.1.8.4.1.1 |
swL3DHCPRelayOption60RelayIpThis object indicates the IP address of relay server.ro IpAddress .1.3.6.1.4.1.171.11.113.10.1.3.3.1.8.4.1.2 |
swL3DHCPRelayOption60MatchTypeThis object indicates match state of this entry.
exact(1): means the option 60 string in the packet must full
match with the specified string.
partial(2): means the option 60 string in the packet only need
partial match with the specified string.rw Enumeration .1.3.6.1.4.1.171.11.113.10.1.3.3.1.8.4.1.3 |
swL3DHCPRelayOption60RowStatusThis object indicates the status of this entry.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.171.11.113.10.1.3.3.1.8.4.1.4 |
swL3DHCPRelayOption61 OBJECT IDENTIFIER .1.3.6.1.4.1.171.11.113.10.1.3.3.1.9 |
swL3DHCPRelayOption61StateThis object indicates DHCP relay option 61 function is enabled or
disabled.rw Enumeration .1.3.6.1.4.1.171.11.113.10.1.3.3.1.9.1 |
swL3DHCPRelayOption61DefModeThis object indicates default mode that has no option 61 mathcing rules.
relay(1): means to relay the packet to the IP address which is specified
by swL3DHCPRelayOption61DefRelayIp.
drop(2): means to drop the packet.rw Enumeration .1.3.6.1.4.1.171.11.113.10.1.3.3.1.9.2 |
swL3DHCPRelayOption61DefRelayIpThis object indicates the IP address of default relay server
that has no option 61 mathcing rules.
Pay attention to when swL3DHCPRelayOption61Mode is:
relay(1): this object must be set together.
drop(2): this object can not be set, and it always returns '0.0.0.0'.rw IpAddress .1.3.6.1.4.1.171.11.113.10.1.3.3.1.9.3 |
swL3DHCPRelayOption61TableThis table indicates the relay servers for the packet at option 61 rules. SEQUENCE OF SwL3DHCPRelayOption61Entry .1.3.6.1.4.1.171.11.113.10.1.3.3.1.9.4 |
swL3DHCPRelayOption61EntryA list of information indicates the relay servers for the packet
at option 61 rules. SwL3DHCPRelayOption61Entry .1.3.6.1.4.1.171.11.113.10.1.3.3.1.9.4.1 |
swL3DHCPRelayOption61ClientTypeThis object indicates client type of this entry.
mac(1): means the client-ID which is the MAC address of client.
string(2): means the client-ID which is specified string by administrator.ro Enumeration .1.3.6.1.4.1.171.11.113.10.1.3.3.1.9.4.1.1 |
swL3DHCPRelayOption61ClientIDThis object indicates string of this entry.
When swL3DHCPRelayOption61ClientType is mac(1), the format of this
object should be XX-XX-XX-XX-XX-XX (MAC address).ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.171.11.113.10.1.3.3.1.9.4.1.2 |
swL3DHCPRelayOption61ModeThis object indicates mode of this entry.
relay(1): means to relay the packet to the IP address which is specified
by swL3DHCPRelayOption61RelayIp.
drop(2): means to drop the packet.rw Enumeration .1.3.6.1.4.1.171.11.113.10.1.3.3.1.9.4.1.3 |
swL3DHCPRelayOption61RelayIpThis object indicates the IP address of relay server.
Pay attention to when swL3DHCPRelayOption61Mode is:
relay(1): this object must be set together.
drop(2): this object can not be set, and it always returns '0.0.0.0'.rw IpAddress .1.3.6.1.4.1.171.11.113.10.1.3.3.1.9.4.1.4 |
swL3DHCPRelayOption61RowStatusThis object indicates the status of this entry.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.171.11.113.10.1.3.3.1.9.4.1.5 |
swL3RelayDnsMgmt OBJECT IDENTIFIER .1.3.6.1.4.1.171.11.113.10.1.3.3.2 |
swL3RelayDnsStateThis object indicates if the DNS Relay function is enabled or
disabled.rw Enumeration .1.3.6.1.4.1.171.11.113.10.1.3.3.2.1 |
swL3RelayDnsPrimaryServerThis object indicates the address of the primary DNS server.rw IpAddress .1.3.6.1.4.1.171.11.113.10.1.3.3.2.2 |
swL3RelayDnsSecondaryServerThis object indicates the address of the secondary DNS server.rw IpAddress .1.3.6.1.4.1.171.11.113.10.1.3.3.2.3 |
swL3RelayDnsCacheStateThis object indicates DNS Relay cache is enabled or
disabled.rw Enumeration .1.3.6.1.4.1.171.11.113.10.1.3.3.2.4 |
swL3RelayDnsStaticTableStateThis object indicates DNS Relay static table is enabled or
disabled.rw Enumeration .1.3.6.1.4.1.171.11.113.10.1.3.3.2.5 |
swL3RelayDnsCtrlTableThis table displays the current DNS relay static table. SEQUENCE OF SwL3RelayDnsCtrlEntry .1.3.6.1.4.1.171.11.113.10.1.3.3.2.6 |
swL3RelayDnsCtrlEntryA list of information display the current DNS relay static
table. SwL3RelayDnsCtrlEntry .1.3.6.1.4.1.171.11.113.10.1.3.3.2.6.1 |
swL3RelayDnsCtrlDomainNameThe domain name of the entry.ro DisplayString .1.3.6.1.4.1.171.11.113.10.1.3.3.2.6.1.1 |
swL3RelayDnsCtrlIpAddrThe IP address of the entry.ro IpAddress .1.3.6.1.4.1.171.11.113.10.1.3.3.2.6.1.2 |
swL3RelayDnsCtrlStateThis object indicates the status of this entry.
other(1) - this entry is currently in use but the conditions
under which it will remain so are different from each of
the following values.
invalid(2) - writing this value to the object, and then the
corresponding entry will be removed from the table.
valid(3) - this entry is reside in the table.rw Enumeration .1.3.6.1.4.1.171.11.113.10.1.3.3.2.6.1.3 |
swL3Md5TableThis table displays the current MD5 key table. SEQUENCE OF SwL3Md5Entry .1.3.6.1.4.1.171.11.113.10.1.3.4 |
swL3Md5EntryA list of information displays the current MD5 key table. SwL3Md5Entry .1.3.6.1.4.1.171.11.113.10.1.3.4.1 |
swL3Md5KeyIdThe MD5 key ID.ro INTEGER .1.3.6.1.4.1.171.11.113.10.1.3.4.1.1 |
swL3Md5KeyAn MD5 password of up to 16 bytes.rw DisplayString .1.3.6.1.4.1.171.11.113.10.1.3.4.1.2 |
swL3Md5RowStatusThis object indicates the status of this entry.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.171.11.113.10.1.3.4.1.3 |
swL3RouteRedistriTableRoute redistribution allows routers on the network that are
running different routing protocols to exchange routing
information. This is accomplished by comparing the routes stored
in the varios routers' routing tables and assigning appropriate
metrics. This information is then exchanged among the various
routers according to the individual routers current routing
protocol. SEQUENCE OF SwL3RouteRedistriEntry .1.3.6.1.4.1.171.11.113.10.1.3.5 |
swL3RouteRedistriEntryA list of information displaying the route redistribution table. SwL3RouteRedistriEntry .1.3.6.1.4.1.171.11.113.10.1.3.5.1 |
swL3RouteRedistriSrcProtocolAllows the selection of the protocol of the source device.ro Enumeration .1.3.6.1.4.1.171.11.113.10.1.3.5.1.1 |
swL3RouteRedistriDstProtocolAllows the selection of the protocol of the destination device.ro Enumeration .1.3.6.1.4.1.171.11.113.10.1.3.5.1.2 |
swL3RouteRedistriTypeAllows the selection of one of the methods for calculating
the metric value.rw Enumeration .1.3.6.1.4.1.171.11.113.10.1.3.5.1.3 |
swL3RouteRedistriMetricAllows the entry of an OSPF interface cost. This is analogous
to a Hop Count in the RIP routing protocol. The value '0'
indicates default value.rw Unsigned32 .1.3.6.1.4.1.171.11.113.10.1.3.5.1.4 |
swL3RouteRedistriRowStatusThis object indicates the status of this entry.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.171.11.113.10.1.3.5.1.5 |
swL3RouteRedistriRouteMapNameThis Object just works when the destination protocol is BGP
and indicate the route-map working when redistribute the route
to BGP.rw DisplayString .1.3.6.1.4.1.171.11.113.10.1.3.5.1.6 |
swL3OspfHostTableThe list of Hosts, and their metrics, that the router will
advertise as host routes. SEQUENCE OF SwL3OspfHostEntry .1.3.6.1.4.1.171.11.113.10.1.3.6 |
swL3OspfHostEntryA metric to be advertised, for a given type of service, when a
given host is reachable. SwL3OspfHostEntry .1.3.6.1.4.1.171.11.113.10.1.3.6.1 |
swL3OspfHostIpAddressThe IP Address of the Host.ro IpAddress .1.3.6.1.4.1.171.11.113.10.1.3.6.1.1 |
swL3OspfHostTOSThe Type of Service of the route being configured.ro TOSType (OSPF-MIB) .1.3.6.1.4.1.171.11.113.10.1.3.6.1.2 |
swL3OspfHostMetricThe Metric to be advertised.rw Metric (OSPF-MIB) .1.3.6.1.4.1.171.11.113.10.1.3.6.1.3 |
swL3OspfHostAreaIDThe Area the Host Entry is to be found within. By default, the
area that a subsuming OSPF interface is in, or 0.0.0.0rw AreaID (OSPF-MIB) .1.3.6.1.4.1.171.11.113.10.1.3.6.1.4 |
swL3OspfHostStatusThis variable displays the status of the entry. Setting it to
'invalid' has the effect of rendering it inoperative. The internal
effect (row removal) is implementation dependent.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.171.11.113.10.1.3.6.1.5 |
swL3ospfVirtIfTableInformation about this router's virtual inter-
faces. SEQUENCE OF SwL3OspfVirtIfEntry .1.3.6.1.4.1.171.11.113.10.1.3.7 |
swL3ospfVirtIfEntryInformation about a single Virtual Interface. SwL3OspfVirtIfEntry .1.3.6.1.4.1.171.11.113.10.1.3.7.1 |
swL3ospfVirtIfAreaIdThe Transit Area that the Virtual Link
traverses. By definition, this is not 0.0.0.0ro AreaID (OSPF-MIB) .1.3.6.1.4.1.171.11.113.10.1.3.7.1.1 |
swL3ospfVirtIfNeighborThe Router ID of the Virtual Neighbor.ro RouterID (OSPF-MIB) .1.3.6.1.4.1.171.11.113.10.1.3.7.1.2 |
swL3ospfVirtIfTransitDelayThe estimated number of seconds it takes to
transmit a link- state update packet over this
interface.rw UpToMaxAge (OSPF-MIB) .1.3.6.1.4.1.171.11.113.10.1.3.7.1.3 |
swL3ospfVirtIfRetransIntervalThe number of seconds between link-state ad-
vertisement retransmissions, for adjacencies
belonging to this interface. This value is
also used when retransmitting database descrip-
tion and link-state request packets. This
value should be well over the expected round-
trip time.rw UpToMaxAge (OSPF-MIB) .1.3.6.1.4.1.171.11.113.10.1.3.7.1.4 |
swL3ospfVirtIfHelloIntervalThe length of time, in seconds, between the
Hello packets that the router sends on the in-
terface. This value must be the same for the
virtual neighbor.rw HelloRange (OSPF-MIB) .1.3.6.1.4.1.171.11.113.10.1.3.7.1.5 |
swL3ospfVirtIfRtrDeadIntervalThe number of seconds that a router's Hello
packets have not been seen before it's neigh-
bors declare the router down. This should be
some multiple of the Hello interval. This
value must be the same for the virtual neigh-
bor.rw Integer32 .1.3.6.1.4.1.171.11.113.10.1.3.7.1.6 |
swL3ospfVirtIfStateOSPF virtual interface states.ro Enumeration .1.3.6.1.4.1.171.11.113.10.1.3.7.1.7 |
swL3ospfVirtIfEventsThe number of state changes or error events on
this Virtual Linkro Counter32 .1.3.6.1.4.1.171.11.113.10.1.3.7.1.8 |
swL3ospfVirtIfAuthTypeThe authentication type specified for a virtu-
al interface. Additional authentication types
may be assigned locally.rw INTEGER .1.3.6.1.4.1.171.11.113.10.1.3.7.1.9 |
swL3ospfVirtIfAuthKeyIf Authentication Type is simplePassword, the
device will left adjust and zero fill to 8 oc-
tets.
Note that unauthenticated interfaces need no
authentication key, and simple password authen-
tication cannot use a key of more than 8 oc-
tets. Larger keys are useful only with authen-
tication mechanisms not specified in this docu-
ment.rw OCTET STRING .1.3.6.1.4.1.171.11.113.10.1.3.7.1.10 |
swL3ospfVirtIfAuthKeyIDThe MD5 key ID.rw INTEGER .1.3.6.1.4.1.171.11.113.10.1.3.7.1.11 |
swL3ospfVirtIfStatusThis variable displays the status of the en-
try. Setting it to 'invalid' has the effect of
rendering it inoperative. The internal effect
(row removal) is implementation dependent.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.171.11.113.10.1.3.7.1.12 |
swL3ospfIfTableThe OSPF Interface Table describes the inter-
faces from the viewpoint of OSPF. SEQUENCE OF SwL3OspfIfEntry .1.3.6.1.4.1.171.11.113.10.1.3.8 |
swL3ospfIfEntryThe OSPF Interface Entry describes one inter-
face from the viewpoint of OSPF. SwL3OspfIfEntry .1.3.6.1.4.1.171.11.113.10.1.3.8.1 |
swL3ospfIfIpAddressThe IP address of this OSPF interface.ro IpAddress .1.3.6.1.4.1.171.11.113.10.1.3.8.1.1 |
swL3ospfAddressLessIfFor the purpose of easing the instancing of
addressed and addressless interfaces; This
variable takes the value 0 on interfaces with
IP Addresses, and the corresponding value of
ifIndex for interfaces having no IP Address.ro Integer32 .1.3.6.1.4.1.171.11.113.10.1.3.8.1.2 |
swL3ospfIfAreaIdA 32-bit integer uniquely identifying the area
to which the interface connects. Area ID
0.0.0.0 is used for the OSPF backbone.rw AreaID (OSPF-MIB) .1.3.6.1.4.1.171.11.113.10.1.3.8.1.3 |
swL3ospfIfTypeThe OSPF interface type.
By way of a default, this field may be intuited
from the corresponding value of ifType. Broad-
cast LANs, such as Ethernet and IEEE 802.5,
take the value 'broadcast', X.25 and similar
technologies take the value 'nbma', and links
that are definitively point to point take the
value 'pointToPoint'.rw Enumeration .1.3.6.1.4.1.171.11.113.10.1.3.8.1.4 |
swL3ospfIfAdminStatThe OSPF interface's administrative status.
The value formed on the interface, and the in-
terface will be advertised as an internal route
to some area. The value 'disabled' denotes
that the interface is external to OSPF.rw Status (OSPF-MIB) .1.3.6.1.4.1.171.11.113.10.1.3.8.1.5 |
swL3ospfIfRtrPriorityThe priority of this interface. Used in
multi-access networks, this field is used in
the designated router election algorithm. The
value 0 signifies that the router is not eligi-
ble to become the designated router on this
particular network. In the event of a tie in
this value, routers will use their Router ID as
a tie breaker.rw DesignatedRouterPriority (OSPF-MIB) .1.3.6.1.4.1.171.11.113.10.1.3.8.1.6 |
swL3ospfIfTransitDelayThe estimated number of seconds it takes to
transmit a link state update packet over this
interface.rw UpToMaxAge (OSPF-MIB) .1.3.6.1.4.1.171.11.113.10.1.3.8.1.7 |
swL3ospfIfRetransIntervalThe number of seconds between link-state ad-
vertisement retransmissions, for adjacencies
belonging to this interface. This value is
also used when retransmitting database descrip-
tion and link-state request packets.rw UpToMaxAge (OSPF-MIB) .1.3.6.1.4.1.171.11.113.10.1.3.8.1.8 |
swL3ospfIfHelloIntervalThe length of time, in seconds, between the
Hello packets that the router sends on the in-
terface. This value must be the same for all
routers attached to a common network.rw HelloRange (OSPF-MIB) .1.3.6.1.4.1.171.11.113.10.1.3.8.1.9 |
swL3ospfIfRtrDeadIntervalThe number of seconds that a router's Hello
packets have not been seen before it's neigh-
bors declare the router down. This should be
some multiple of the Hello interval. This
value must be the same for all routers attached
to a common network.rw PositiveInteger (OSPF-MIB) .1.3.6.1.4.1.171.11.113.10.1.3.8.1.10 |
swL3ospfIfPollIntervalThe larger time interval, in seconds, between
the Hello packets sent to an inactive non-
broadcast multi- access neighbor.rw PositiveInteger (OSPF-MIB) .1.3.6.1.4.1.171.11.113.10.1.3.8.1.11 |
swL3ospfIfStateThe OSPF Interface State.ro Enumeration .1.3.6.1.4.1.171.11.113.10.1.3.8.1.12 |
swL3ospfIfDesignatedRouterThe IP Address of the Designated Router.ro IpAddress .1.3.6.1.4.1.171.11.113.10.1.3.8.1.13 |
swL3ospfIfBackupDesignatedRouterThe IP Address of the Backup Designated
Router.ro IpAddress .1.3.6.1.4.1.171.11.113.10.1.3.8.1.14 |
swL3ospfIfEventsThe number of times this OSPF interface has
changed its state, or an error has occurred.ro Counter32 .1.3.6.1.4.1.171.11.113.10.1.3.8.1.15 |
swL3ospfIfMulticastForwardingThe way multicasts should forwarded on this
interface; not forwarded, forwarded as data
link multicasts, or forwarded as data link uni-
casts. Data link multicasting is not meaning-
ful on point to point and NBMA interfaces, and
setting ospfMulticastForwarding to 0 effective-
ly disables all multicast forwarding.rw Enumeration .1.3.6.1.4.1.171.11.113.10.1.3.8.1.16 |
swL3ospfIfDemandIndicates whether Demand OSPF procedures (hel-
lo supression to FULL neighbors and setting the
DoNotAge flag on proogated LSAs) should be per-
formed on this interface.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.171.11.113.10.1.3.8.1.17 |
swL3ospfIfAuthTypeThe authentication type specified for an in-
terface. Additional authentication types may
be assigned locally.rw INTEGER .1.3.6.1.4.1.171.11.113.10.1.3.8.1.18 |
swL3ospfIfAuthKeyThe Authentication Key. If the Area's Author-
ization Type is simplePassword, and the key
length is shorter than 8 octets, the agent will
left adjust and zero fill to 8 octets.
Note that unauthenticated interfaces need no
authentication key, and simple password authen-
tication cannot use a key of more than 8 oc-
tets. Larger keys are useful only with authen-
tication mechanisms not specified in this docu-
ment.
When read, ospfIfAuthKey always returns an Oc-
tet String of length zero.rw OCTET STRING .1.3.6.1.4.1.171.11.113.10.1.3.8.1.19 |
swL3ospfIfAuthKeyIDThe MD5 key ID.rw INTEGER .1.3.6.1.4.1.171.11.113.10.1.3.8.1.20 |
swL3ospfIfPassiveModeAssign the designated entry to be a passive interface.rw Enumeration .1.3.6.1.4.1.171.11.113.10.1.3.8.1.21 |
swL3ospfIfMetricThe Metric to be advertised.rw Metric (OSPF-MIB) .1.3.6.1.4.1.171.11.113.10.1.3.8.1.23 |
swL3RoutePreference OBJECT IDENTIFIER .1.3.6.1.4.1.171.11.113.10.1.3.9 |
swL3RoutePreferenceRIPUsed to configure the route preference of RIP.rw INTEGER .1.3.6.1.4.1.171.11.113.10.1.3.9.1 |
swL3RoutePreferenceOSPFIntraUsed to configure the route preference of OSPF Intra.rw INTEGER .1.3.6.1.4.1.171.11.113.10.1.3.9.2 |
swL3RoutePreferenceStaticUsed to configure the route preference of Static.rw INTEGER .1.3.6.1.4.1.171.11.113.10.1.3.9.3 |
swL3RoutePreferenceLocalUsed to read the route preference of Local.ro INTEGER .1.3.6.1.4.1.171.11.113.10.1.3.9.4 |
swL3RoutePreferenceOSPFInterUsed to configure the route preference of OSPF Inter.rw INTEGER .1.3.6.1.4.1.171.11.113.10.1.3.9.5 |
swL3RoutePreferenceOSPFExtT1Used to configure the route preference of OSPFExtT1.rw INTEGER .1.3.6.1.4.1.171.11.113.10.1.3.9.6 |
swL3RoutePreferenceOSPFExtT2Used to configure the route preference of OSPF ExtT2.rw INTEGER .1.3.6.1.4.1.171.11.113.10.1.3.9.7 |
swL3RoutePreferenceDefaultUsed to configure the route preference of Default route.rw INTEGER .1.3.6.1.4.1.171.11.113.10.1.3.9.8 |
swL3RoutePreferenceEBGPUsed to configure the route preference of EBGP.rw INTEGER .1.3.6.1.4.1.171.11.113.10.1.3.9.9 |
swL3RoutePreferenceIBGPUsed to configure the route preference of IBGP.rw INTEGER .1.3.6.1.4.1.171.11.113.10.1.3.9.10 |
swL3ospfAreaTableInformation describing the configured parame-
ters and cumulative statistics of the router's
attached areas. SEQUENCE OF SwL3ospfAreaEntry .1.3.6.1.4.1.171.11.113.10.1.3.10 |
swL3ospfAreaEntryInformation describing the configured parame-
ters and cumulative statistics of one of the
router's attached areas. SwL3ospfAreaEntry .1.3.6.1.4.1.171.11.113.10.1.3.10.1 |
swL3ospfAreaIdA 32-bit integer uniquely identifying an area.
Area ID 0.0.0.0 is used for the OSPF backbone.ro AreaID (OSPF-MIB) .1.3.6.1.4.1.171.11.113.10.1.3.10.1.1 |
swL3ospfAreaTypeThe type specified for an area.rwobsolete Enumeration .1.3.6.1.4.1.171.11.113.10.1.3.10.1.2 |
swL3ospfAreaSummaryStateWhether the summary LSA is effective for this area.rw Enumeration .1.3.6.1.4.1.171.11.113.10.1.3.10.1.3 |
swL3ospfAreaMetricEnter the metric (1 - 65535; 0 for auto cost) of this area.rw Integer32 .1.3.6.1.4.1.171.11.113.10.1.3.10.1.4 |
swL3ospfAreaTranslateState.rw Enumeration .1.3.6.1.4.1.171.11.113.10.1.3.10.1.5 |
swL3ospfAreaStatusThis variable displays the status of the en-
try. Setting it to 'invalid' has the effect of
rendering it inoperative. The internal effect
(row removal) is implementation dependent.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.171.11.113.10.1.3.10.1.6 |
swL3dvmrpInterfaceTableThe (conceptual) table listing the router's multicast-
capable interfaces. SEQUENCE OF SwL3dvmrpInterfaceEntry .1.3.6.1.4.1.171.11.113.10.1.3.12 |
swL3dvmrpInterfaceEntryAn entry (conceptual row) in the dvmrpInterfaceTable. This
row augments ipMRouteInterfaceEntry in the IP Multicast MIB,
where the threshold object resides. SwL3dvmrpInterfaceEntry .1.3.6.1.4.1.171.11.113.10.1.3.12.1 |
swL3dvmrpInterfaceIfIndexThe ifIndex value of the interface for which DVMRP is
enabled. Integer32 .1.3.6.1.4.1.171.11.113.10.1.3.12.1.1 |
swL3dvmrpInterfaceLocalAddressThe IP address this system will use as a source address on
this interface. On unnumbered interfaces, it must be the
same value as dvmrpInterfaceLocalAddress for some interface
on the system.rw IpAddress .1.3.6.1.4.1.171.11.113.10.1.3.12.1.2 |
swL3dvmrpInterfaceMetricThe distance metric for this interface which is used to
calculate distance vectors.rw Integer32 .1.3.6.1.4.1.171.11.113.10.1.3.12.1.3 |
swL3dvmrpInterfaceProbeProbe distribution interval.rw Integer32 .1.3.6.1.4.1.171.11.113.10.1.3.12.1.4 |
swL3dvmrpInterfaceNbrTimeoutUsed to set the timer before neighbors are timed out.rw Integer32 .1.3.6.1.4.1.171.11.113.10.1.3.12.1.5 |
swL3dvmrpInterfaceStatusThe status of this entry. Creating the entry enables DVMRP
on the virtual interface; destroying the entry or setting it
to notInService disables DVMRP on the virtual interface.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.171.11.113.10.1.3.12.1.6 |
swL3dvmrpInterfaceRcvBadPktsThe number of DVMRP packets received on the interface by
the DVMRP process which were subsequently discarded as
invalid (e.g. invalid packet format, or a route report from
an unknown neighbor).ro Counter32 .1.3.6.1.4.1.171.11.113.10.1.3.12.1.7 |
swL3dvmrpInterfaceRcvBadRoutesThe number of routes, in valid DVMRP packets, which were
ignored because the entry was invalid.ro Counter32 .1.3.6.1.4.1.171.11.113.10.1.3.12.1.8 |
swL3OspfLsdbMgmt OBJECT IDENTIFIER .1.3.6.1.4.1.171.11.113.10.1.3.13 |
swL3OspfInternalLsdbTableThe OSPF Process's Link State Database. SEQUENCE OF SwL3OspfInternalLsdbEntry .1.3.6.1.4.1.171.11.113.10.1.3.13.1 |
swL3OspfInternalLsdbEntryA single Link State Advertisement. SwL3OspfInternalLsdbEntry .1.3.6.1.4.1.171.11.113.10.1.3.13.1.1 |
swL3OspfInternalLsdbAreaIdThe 32 bit identifier of the Area from which
the LSA was received.ro AreaID (OSPF-MIB) .1.3.6.1.4.1.171.11.113.10.1.3.13.1.1.1 |
swL3OspfInternalLsdbTypeThe type of the link state advertisement.
Each link state type has a separate advertise-
ment format.ro Enumeration .1.3.6.1.4.1.171.11.113.10.1.3.13.1.1.2 |
swL3OspfInternalLsdbLsidThe Link State ID is an LS Type Specific field
containing either a Router ID or an IP Address;
it identifies the piece of the routing domain
that is being described by the advertisement.ro IpAddress .1.3.6.1.4.1.171.11.113.10.1.3.13.1.1.3 |
swL3OspfInternalLsdbRouterIdThe 32 bit number that uniquely identifies the
originating router in the Autonomous System.ro RouterID (OSPF-MIB) .1.3.6.1.4.1.171.11.113.10.1.3.13.1.1.4 |
swL3OspfInternalLsdbMetricEnter the metric (1 - 65535; 0 for auto cost) of this area.ro Integer32 .1.3.6.1.4.1.171.11.113.10.1.3.13.1.1.5 |
swL3OspfInternalLsdbSequenceNoThe sequence number field is a signed 32-bit
integer. It is used to detect old and dupli-
cate link state advertisements. The space of
sequence numbers is linearly ordered. The
larger the sequence number the more recent the
advertisement.ro OCTET STRING .1.3.6.1.4.1.171.11.113.10.1.3.13.1.1.6 |
swL3OspfInternalLsdbAgeThis field is the age of the link state adver-
tisement in seconds.ro Unsigned32 -- Should be 0..MaxAge .1.3.6.1.4.1.171.11.113.10.1.3.13.1.1.7 |
swL3OspfInternalLsdbChecksumThis field is the checksum of the complete
contents of the advertisement, excepting the
age field. The age field is excepted so that
an advertisement's age can be incremented
without updating the checksum. The checksum
used is the same that is used for ISO connec-
tionless datagrams; it is commonly referred to
as the Fletcher checksum.ro Integer32 .1.3.6.1.4.1.171.11.113.10.1.3.13.1.1.8 |
swL3OspfExternalLsdbTableThe OSPF Process's Links State Database. SEQUENCE OF SwL3OspfExternalLsdbEntry .1.3.6.1.4.1.171.11.113.10.1.3.13.2 |
swL3OspfExternalLsdbEntryA single Link State Advertisement. SwL3OspfExternalLsdbEntry .1.3.6.1.4.1.171.11.113.10.1.3.13.2.1 |
swL3OspfExternalLsdbTypeThe type of the link state advertisement.
Each link state type has a separate advertise-
ment format.ro Enumeration .1.3.6.1.4.1.171.11.113.10.1.3.13.2.1.1 |
swL3OspfExternalLsdbLsidThe Link State ID is an LS Type Specific field
containing either a Router ID or an IP Address;
it identifies the piece of the routing domain
that is being described by the advertisement.ro IpAddress .1.3.6.1.4.1.171.11.113.10.1.3.13.2.1.2 |
swL3OspfExternalLsdbRouterIdThe 32 bit number that uniquely identifies the
originating router in the Autonomous System.ro RouterID (OSPF-MIB) .1.3.6.1.4.1.171.11.113.10.1.3.13.2.1.3 |
swL3OspfExternalLsdbMetricEnter the metric (1 - 65535; 0 for auto cost) of this area.ro Integer32 .1.3.6.1.4.1.171.11.113.10.1.3.13.2.1.4 |
swL3OspfExternalLsdbMetricTypeEnter the metric type of this area.ro Enumeration .1.3.6.1.4.1.171.11.113.10.1.3.13.2.1.5 |
swL3OspfExternalLsdbSequenceNoThe sequence number field is a signed 32-bit
integer. It is used to detect old and dupli-
cate link state advertisements. The space of
sequence numbers is linearly ordered. The
larger the sequence number the more recent the
advertisement.ro OCTET STRING .1.3.6.1.4.1.171.11.113.10.1.3.13.2.1.6 |
swL3OspfExternalLsdbAgeThis field is the age of the link state adver-
tisement in seconds.ro Unsigned32 -- Should be 0..MaxAge .1.3.6.1.4.1.171.11.113.10.1.3.13.2.1.7 |
swL3OspfExternalLsdbChecksumThis field is the checksum of the complete
contents of the advertisement, except the
age field. The age field is the exception so that
an advertisement's age can be incremented
without updating the checksum. The checksum
used is the same that is used for ISO connec-
tionless datagrams; it is commonly referred to
as the Fletcher checksum.ro Integer32 .1.3.6.1.4.1.171.11.113.10.1.3.13.2.1.8 |
swL3OspfExternalLsdbForwardingAddressThis field is the forwarding address.ro IpAddress .1.3.6.1.4.1.171.11.113.10.1.3.13.2.1.9 |
swL3OspfExternalLsdbRouteTagThis field is the route tag.ro OCTET STRING .1.3.6.1.4.1.171.11.113.10.1.3.13.2.1.10 |
swL3VrrpOperMgmt OBJECT IDENTIFIER .1.3.6.1.4.1.171.11.113.10.1.3.14 |
swL3VrrpOperTableOperations table for a VRRP router which consists of a
sequence (i.e., one or more conceptual rows) of
'swL3vrrpOperEntry' items. SEQUENCE OF SwL3VrrpOperEntry .1.3.6.1.4.1.171.11.113.10.1.3.14.1 |
swL3VrrpOperEntryAn entry in the vrrpOperTable containing the operational
characteristics of a virtual router. On a VRRP router,
a given virtual router is identified by a combination
of the IF index and VRID.
Rows in the table cannot be modified unless the value
of `swL3VrrpOperAdminState' is `disabled' and the
`swL3VrrpOperState' has transitioned to `initialize'. SwL3VrrpOperEntry .1.3.6.1.4.1.171.11.113.10.1.3.14.1.1 |
swL3VrrpOperIfIndexThe ifIndex value of the interface for which VRRP is
enabled.ro Integer32 .1.3.6.1.4.1.171.11.113.10.1.3.14.1.1.1 |
swL3VrrpOperVrIdThis object contains the Virtual Router Identifier (VRID).ro VrId .1.3.6.1.4.1.171.11.113.10.1.3.14.1.1.2 |
swL3VrrpOperVirtualMacAddrThe virtual MAC address of the virtual router. Although this
object can be derived from the 'swL3VrrpOperVrId' object, it is
defined so that it is easily obtainable by a management
application and can be included in VRRP-related SNMP traps.ro MacAddress (SNMPv2-TC) .1.3.6.1.4.1.171.11.113.10.1.3.14.1.1.3 |
swL3VrrpOperStateThe current state of the virtual router. This object has
three defined values:
- `initialize', which indicates that all the
virtual router is waiting for a startup event.
- `backup', which indicates the virtual router is
monitoring the availability of the master router.
- `master', which indicates that the virtual router
is forwarding packets for IP addresses that are
associated with this router.
Setting the `swL3VrrpOperAdminState' object (below) initiates
transitions in the value of this object.ro Enumeration .1.3.6.1.4.1.171.11.113.10.1.3.14.1.1.4 |
swL3VrrpOperAdminStateThis object will enable/disable the virtual router
function. Setting the value to `up', will transition
the state of the virtual router from `initialize' to `backup'
or `master', depending on the value of `swL3VrrpOperPriority'.
Setting the value to `down', will transition the
router from `master' or `backup' to `initialize'. State
transitions may not be immediate; they sometimes depend on
other factors, such as the interface (IF) state.
The `swL3VrrpOperAdminState' object must be set to `down' prior
to modifying the other read-create objects in the conceptual
row. The value of the `swL3VrrpOperRowStatus' object (below)
must be `active', signifying that the conceptual row
is valid (i.e., the objects are correctly set),
in order for this object to be set to `up'.rw Enumeration .1.3.6.1.4.1.171.11.113.10.1.3.14.1.1.5 |
swL3VrrpOperPriorityThis object specifies the priority to be used for the
virtual router master election process. Higher values imply
higher priority.
A priority of '0', although not settable, is sent by
the master router to indicate that this router has ceased
to participate in VRRP and a backup virtual router should
transition to become a new master.
A priority of 255 is used for the router that owns the
associated IP address(es).rw Integer32 .1.3.6.1.4.1.171.11.113.10.1.3.14.1.1.6 |
swL3VrrpOperMasterIpAddrThe master router's real (primary) IP address. This is
the IP address listed as the source in VRRP advertisement
last received by this virtual router.ro IpAddress .1.3.6.1.4.1.171.11.113.10.1.3.14.1.1.7 |
swL3VrrpOperCriticalIpAddrIn the case where there is more than one IP address for
a given `ifIndex', this object is used to specify the IP
address that will become the `swL3VrrpOperMasterIpAddr', should
the virtual router transition from backup to master. If
this object is set to 0.0.0.0, the IP address which is
numerically lowest will be selected.rw IpAddress .1.3.6.1.4.1.171.11.113.10.1.3.14.1.1.8 |
swL3VrrpOperCheckCriticalIpStateCritical IP state.rw Enumeration .1.3.6.1.4.1.171.11.113.10.1.3.14.1.1.9 |
swL3VrrpOperAuthTypeAuthentication type used for VRRP protocol exchanges between
virtual routers. This value of this object is the same for a
given ifIndex.
New enumerations to this list can only be added via a new
RFC on the standards track.rw Enumeration .1.3.6.1.4.1.171.11.113.10.1.3.14.1.1.10 |
swL3VrrpOperAuthKeyThe Authentication Key. This object is set according to
the value of the 'swL3VrrpOperAuthType' object
('simpleTextPassword' or 'ipAuthenticationHeader'). If the
length of the value is less than 16 octets, the agent will
left adjust and zero fill to 16 octets. The value of this
object is the same for a given ifIndex.
When read, swL3VrrpOperAuthKey always returns an Octet String
of length zero.rw OCTET STRING .1.3.6.1.4.1.171.11.113.10.1.3.14.1.1.11 |
swL3VrrpOperAdvertisementIntervalThe time interval, in seconds, between sending
advertisement messages. Only the master router sends
VRRP advertisements.rw Integer32 .1.3.6.1.4.1.171.11.113.10.1.3.14.1.1.12 |
swL3VrrpOperPreemptModeControls whether a higher priority virtual router will
preempt a lower priority master.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.171.11.113.10.1.3.14.1.1.13 |
swL3VrrpOperVirtualRouterUpTimeThis is the value of the `sysUpTime' object when this
virtual router (i.e., the `swL3VrrpOperState') transitioned
out of `initialized'.ro TimeStamp (SNMPv2-TC) .1.3.6.1.4.1.171.11.113.10.1.3.14.1.1.14 |
swL3VrrpOperVirtualIpAddrThe assigned IP addresses that a virtual router is
responsible for backing up.rw IpAddress .1.3.6.1.4.1.171.11.113.10.1.3.14.1.1.15 |
swL3VrrpOperRowStatusThe row status variable, used in accordance to installation
and removal conventions for conceptual rows. The rowstatus of
a currently active row in the vrrpOperTable is constrained
by the operational state of the corresponding virtual router.
When `vrrpOperRowStatus' is set to active(1), no other
objects in the conceptual row, with the exception of
`swL3VrrpOperAdminState', can be modified. Prior to setting the
`swL3VrrpOperRowStatus' object from `active' to a different value,
the `swL3VrrpOperAdminState' object must be set to `down' and the
`vrrpOperState' object be transitioned to `initialize'.
To create a row in this table, a manager sets this object
to either createAndGo(4) or createAndWait(5). Until instances
of all corresponding columns are appropriately configured,
the value of the corresponding instance of the `vrrpOperRowStatus'
column will be read as notReady(3).
In particular, a newly created row cannot be made active(1)
until (minimally) the corresponding instance of
`swL3VrrpOperVrId' has been set and there is at least one active
row in the `swL3VrrpAssoIpAddrTable' defining an associated
IP address for the virtual router.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.171.11.113.10.1.3.14.1.1.16 |
swL3OspfECMPMgmt OBJECT IDENTIFIER .1.3.6.1.4.1.171.11.113.10.1.3.15 |
swL3OspfECMPIpDestinationIf set to 'enabled (1)', the ECMP algorithm will include the destination IP.rw Enumeration .1.3.6.1.4.1.171.11.113.10.1.3.15.1 |
swL3OspfECMPIpSourceIf set to 'enabled (1)', the ECMP algorithm will include the lower 5 bits of the source IP.
This attribution is mutually exclusive with crc_low and crc_high.
If set to 'enabled (1)', crc_low and crc_high will be excluded.rw Enumeration .1.3.6.1.4.1.171.11.113.10.1.3.15.2 |
swL3OspfECMPCrcLowIf set to 'enabled (1)', the ECMP algorithm will include the lower 5 bits of the CRC. This
attribution is mutually exclusive with crc_high and ip_source.
If set to 'enabled (1)', crc_high and ip_source will be excluded.rw Enumeration .1.3.6.1.4.1.171.11.113.10.1.3.15.3 |
swL3OspfECMPCrcHighIf set to 'enabled (1)', the ECMP algorithm will include the upper 5 bits of the CRC.
This attribution is mutually exclusive with ip_source and crc_low.
If set to 'enabled (1)', crc_low and ip_source will be excluded.rw Enumeration .1.3.6.1.4.1.171.11.113.10.1.3.15.4 |
swL3OspfECMPTCPorUDPportIf set to 'enabled (1)', the ECMP algorithm will include the TCP or UDP port.rw Enumeration .1.3.6.1.4.1.171.11.113.10.1.3.15.5 |
swL3OspfECMPStateThis object indicates the state of the OSPF ECMP function.rw Enumeration .1.3.6.1.4.1.171.11.113.10.1.3.15.6 |
swL3LocalRouteMgmt OBJECT IDENTIFIER .1.3.6.1.4.1.171.11.113.10.1.3.16 |
swL3LocalRouteIPv4GlobalStateThis object indicates the IPv4 local route state of the device.rw Enumeration .1.3.6.1.4.1.171.11.113.10.1.3.16.1 |
swL3LocalRouteIPv6GlobalStateThis object indicates the IPv6 local route state of the device.rw Enumeration .1.3.6.1.4.1.171.11.113.10.1.3.16.2 |
swL3RIPTimerMgmt OBJECT IDENTIFIER .1.3.6.1.4.1.171.11.113.10.1.3.17 |
swL3RIPUpdateTimeThis object indicates the RIP update interval.rw INTEGER .1.3.6.1.4.1.171.11.113.10.1.3.17.1 |
swL3RIPTimeOutTimeThis object indicates the period for which a dynamic RIP route
will be kept in the IPv4 routing table without receiving any updates for the
route.
After this time interval, the route will be invalid and will be aged out.rw INTEGER .1.3.6.1.4.1.171.11.113.10.1.3.17.2 |
swL3RIPGarbageCollectionTimeThis object indicates the period for a RIP route which
has aged out is retained in the IPv4 Routing Table. After
this time interval the route is deleted from the IPv4
Routing Table.rw INTEGER .1.3.6.1.4.1.171.11.113.10.1.3.17.3 |