DES3028G-L2MGMT-MIB
The Structure of Layer 2 Network Management Information for enterprise.
Main OID:
swL2MgmtMIB.1.3.6.1.4.1.171.11.63.11.2
334
Objects
Active
Status
6
Dependencies
Imported Objects
Objects
334 total| Object Name |
|---|
swL2MgmtMIBThe Structure of Layer 2 Network Management Information for enterprise. MODULE-IDENTITY .1.3.6.1.4.1.171.11.63.11.2 |
swL2DevMgmt OBJECT IDENTIFIER .1.3.6.1.4.1.171.11.63.11.2.1 |
swL2DevInfo OBJECT IDENTIFIER .1.3.6.1.4.1.171.11.63.11.2.1.1 |
swL2DevInfoFrontPanelLedStatusThis object is a set of system LED indications.
When log in system DES3028/DES3052 which do not support POE, the first
two octets is defined as system LED. The first LED is power LED. The
second LED is console LED.
When log in system DES3028p/DES3052p which support POE, the first
four octets are defined as system LED. The first octet is 0x02 and the
second octet is 0x01 when in normal mode. Contrarily, the first octet
is 0x01 and the second octet is 0x02 when in poe mode. The third octet
indicates the power LED. The fourth octet indicates the console LED.
The other octets are defined as follow:
start on the third or fifth octets separately correspond to system support
poe or system which does not support poe indicate the logical port LED
(following swL2BasePort ordering). Every two bytes are presented to a port.
The first byte is presentd to the Link/Activity LED. The second byte is
presented to the Speed LED.
Link/Activity LED :
The most significant bit is used for blink/solid:
8 = The LED blinks.
The second significant bit is used for link status:
1 = link fail.
2 = link pass.
Speed LED :
01 = 10Mbps.
02 = 100Mbps.
03 = 1000Mbps.
The four remaining bits are currently unused and must be 0.ro OCTET STRING .1.3.6.1.4.1.171.11.63.11.2.1.1.5 |
swL2DevCtrl OBJECT IDENTIFIER .1.3.6.1.4.1.171.11.63.11.2.1.2 |
swL2DevCtrlSystemRebootThis object indicates the agent system reboot state. The agent always
returns other(1) when this object is read.rw Enumeration .1.3.6.1.4.1.171.11.63.11.2.1.2.1 |
swL2DevCtrlSystemIPThis object indicates system ip.rw IpAddress .1.3.6.1.4.1.171.11.63.11.2.1.2.2 |
swL2DevCtrlSubnetMaskThis object indicates system subnet mask.rw IpAddress .1.3.6.1.4.1.171.11.63.11.2.1.2.3 |
swL2DevCtrlDefaultGatewayThis object indicates system default gateway.rw IpAddress .1.3.6.1.4.1.171.11.63.11.2.1.2.4 |
swL2DevCtrlManagementVlanIdThis object controls which Vlan includes system ip. And the Vlan
should have been created.rw VlanId .1.3.6.1.4.1.171.11.63.11.2.1.2.5 |
swL2DevCtrlIGMPSnoopingThis object indicates layer 2 Internet Group Management Protocol
(IGMP) capture function is enabled or disabled .rw Enumeration .1.3.6.1.4.1.171.11.63.11.2.1.2.7 |
swL2DevCtrlCleanAllStatisticCounterAs the object is set to active, all the statistic counters will be cleared.
If set to normal, do nothing.rw Enumeration .1.3.6.1.4.1.171.11.63.11.2.1.2.12 |
swL2DevCtrlSnmpEnableAuthenTrapsIndicates whether the SNMP entity is permitted to generate
authenticationFailure traps. The value of this object
overrides any configuration information; as such, it
provides a means whereby all authenticationFailure traps may
be disabled.
Note that it is strongly recommended that this object be
stored in non-volatile memory so that it remains constant
across re-initializations of the network management system.rw Enumeration .1.3.6.1.4.1.171.11.63.11.2.1.2.13 |
swL2DevCtrlRmonStateThis object can be enabled or disabled RMON.rw Enumeration .1.3.6.1.4.1.171.11.63.11.2.1.2.16 |
swL2DevCtrlIpAutoConfigIndicates the status of automatically getting configuration from TFTP server on devicerw Enumeration .1.3.6.1.4.1.171.11.63.11.2.1.2.17 |
swL2MACNotifyStateThis object can enabled or disabled MAC Notification.rw Enumeration .1.3.6.1.4.1.171.11.63.11.2.1.2.19 |
swL2MACNotifyHistorySizeThis object indicates the history size of variation MAC in address table.
The default value is 1 .rw INTEGER .1.3.6.1.4.1.171.11.63.11.2.1.2.20 |
swL2MACNotifyIntervalThis object indicates the time interval in second for trigger the MAC notify message.rw INTEGER .1.3.6.1.4.1.171.11.63.11.2.1.2.21 |
swL2DevCtrlLLDPStateSpecifies the state of the LLDP function.
When this function is enabled, the switch can start to transmit
LLDP packets and receive and process the LLDP packets.
The specific function of each port will depend on the per port
LLDP setting.
For the advertisement of LLDP packets, the switch announces the
information to its neighbor through ports. For the receiving of
LLDP packets, the switch will learn the information from the LLDP
packets advertised from the neighbor in the neighbor table.rw Enumeration .1.3.6.1.4.1.171.11.63.11.2.1.2.22 |
swL2DevCtrlLLDPForwardMessageStateWhen lldp is disabled and lldp forward_message is enabled, the received
LLDP Data Units packet will be forwarded.rw Enumeration .1.3.6.1.4.1.171.11.63.11.2.1.2.23 |
swL2DevCtrlAsymVlanStateThis object enables or disables the asymmetric VLAN feature of the device.rw Enumeration .1.3.6.1.4.1.171.11.63.11.2.1.2.24 |
swL2IGMPSnoopingMulticastVlanStateThis indicates the global state of the igmp_snoop multicast_vlan.rw Enumeration .1.3.6.1.4.1.171.11.63.11.2.1.2.25 |
swL2DevCtrlVLANTrunkStateThis indicates the global state of the VLAN trunking feature of the device.rw Enumeration .1.3.6.1.4.1.171.11.63.11.2.1.2.26 |
swL2DevCtrlWeb OBJECT IDENTIFIER .1.3.6.1.4.1.171.11.63.11.2.1.2.27 |
swL2DevCtrlWebStateThis object controls Web status.rw Enumeration .1.3.6.1.4.1.171.11.63.11.2.1.2.27.1 |
swL2DevCtrlTelnet OBJECT IDENTIFIER .1.3.6.1.4.1.171.11.63.11.2.1.2.28 |
swL2DevCtrlTelnetStateThis object controls the Telnet status.rw Enumeration .1.3.6.1.4.1.171.11.63.11.2.1.2.28.1 |
swL2DevAlarm OBJECT IDENTIFIER .1.3.6.1.4.1.171.11.63.11.2.1.3 |
swL2DevAlarmNewRootWhen the device has become the new root of the Spanning Tree,
this object decides whether to send a new root trap.rw Enumeration .1.3.6.1.4.1.171.11.63.11.2.1.3.1 |
swL2DevAlarmTopologyChangeThis object determines whether or not to send a trap message when
the switch topology changes. If the object is enabled (3), the Topology Change
trap is sent by the device when any of its configured ports transition from
the Learning state to the Forwarding state, or from the Forwarding state to
the Blocking state. For the same port transition, the device does not send the
trap if this object value is disabled or in another state.rw Enumeration .1.3.6.1.4.1.171.11.63.11.2.1.3.2 |
swL2DevAlarmLinkChangeThis object determines whether or not to send a trap message when the link
changes. If the object is enabled (3), the Link Change trap is sent by
the device when any of its port links change. The device does not send the
trap if this object value is disabled or in another state.rw Enumeration .1.3.6.1.4.1.171.11.63.11.2.1.3.3 |
swL2PortMgmt OBJECT IDENTIFIER .1.3.6.1.4.1.171.11.63.11.2.2 |
swL2PortInfoTableA table that contains information about every port. SEQUENCE OF SwL2PortInfoEntry .1.3.6.1.4.1.171.11.63.11.2.2.1 |
swL2PortInfoEntryA list of information for each port of the device. SwL2PortInfoEntry .1.3.6.1.4.1.171.11.63.11.2.2.1.1 |
swL2PortInfoPortIndexThis object indicates the module's port number.(1..Max port number in
the module)ro INTEGER .1.3.6.1.4.1.171.11.63.11.2.2.1.1.1 |
swL2PortInfoMediumTypeThis object indicates the port type: fiber or copper.ro Enumeration .1.3.6.1.4.1.171.11.63.11.2.2.1.1.2 |
swL2PortInfoLinkStatusThis object indicates the port link status.ro Enumeration .1.3.6.1.4.1.171.11.63.11.2.2.1.1.4 |
swL2PortInfoNwayStatusThis object indicates the port speed and duplex mode.ro Enumeration .1.3.6.1.4.1.171.11.63.11.2.2.1.1.5 |
swL2PortCtrlTableA table that contains control information about every port. SEQUENCE OF SwL2PortCtrlEntry .1.3.6.1.4.1.171.11.63.11.2.2.2 |
swL2PortCtrlEntryA list of control information for each port of the device. SwL2PortCtrlEntry .1.3.6.1.4.1.171.11.63.11.2.2.2.1 |
swL2PortCtrlPortIndexThis object indicates the module's port number.(1..Max port number in
the module)ro INTEGER .1.3.6.1.4.1.171.11.63.11.2.2.2.1.1 |
swL2PortCtrlPortMediumTypeThis object indicates the port type: fiber or copper.rw Enumeration .1.3.6.1.4.1.171.11.63.11.2.2.2.1.2 |
swL2PortCtrlAdminStateThis object decides whether the port is enabled or disabled.rw Enumeration .1.3.6.1.4.1.171.11.63.11.2.2.2.1.3 |
swL2PortCtrlNwayStateChoose the port speed, duplex mode, and N-Way function mode.rw Enumeration .1.3.6.1.4.1.171.11.63.11.2.2.2.1.4 |
swL2PortCtrlFlowCtrlStateSet the flow control function as enabled or disabled.rw Enumeration .1.3.6.1.4.1.171.11.63.11.2.2.2.1.5 |
swL2PortCtrlDescriptionThe object describes the ports in text.rw DisplayString .1.3.6.1.4.1.171.11.63.11.2.2.2.1.6 |
swL2PortCtrlAddressLearningThis object decides whether the address learning is enabled or disabled.rw Enumeration .1.3.6.1.4.1.171.11.63.11.2.2.2.1.7 |
swL2PortCtrlMACNotifyStateThis object sets each port's MAC notification state.rw Enumeration .1.3.6.1.4.1.171.11.63.11.2.2.2.1.8 |
swL2PortCtrlMulticastfilterThis object decides the multicast packet filtering mode on this port.rw Enumeration .1.3.6.1.4.1.171.11.63.11.2.2.2.1.9 |
swL2PortCtrlMDIXStateThis object configures the MDIX setting of the port.
The value 'other' is for those entries in which MDIX is not applicable.rw Enumeration .1.3.6.1.4.1.171.11.63.11.2.2.2.1.10 |
swL2PortErrTableA table that contains information about the Err port. SEQUENCE OF SwL2PortErrEntry .1.3.6.1.4.1.171.11.63.11.2.2.3 |
swL2PortErrEntryA list of information for the err port of the device. SwL2PortErrEntry .1.3.6.1.4.1.171.11.63.11.2.2.3.1 |
swL2PortErrPortIndexThis object indicates the module's port number.(1..Max port number in
the module)ro INTEGER .1.3.6.1.4.1.171.11.63.11.2.2.3.1.1 |
swL2PortErrPortStateThis object decides whether the port state is enabled or disabled.ro Enumeration .1.3.6.1.4.1.171.11.63.11.2.2.3.1.2 |
swL2PortErrPortStatusThis object decides whether the PortStatus is err-disabled.ro Enumeration .1.3.6.1.4.1.171.11.63.11.2.2.3.1.3 |
swL2PortErrPortReasonThis object indicates the module which disabled the port.ro Enumeration .1.3.6.1.4.1.171.11.63.11.2.2.3.1.4 |
swL2PortErrDescriptionThe object describes the ports in text.ro DisplayString .1.3.6.1.4.1.171.11.63.11.2.2.3.1.5 |
swL2QOSMgmt OBJECT IDENTIFIER .1.3.6.1.4.1.171.11.63.11.2.3 |
swL2QOSBandwidthControlTable. SEQUENCE OF SwL2QOSBandwidthControlEntry .1.3.6.1.4.1.171.11.63.11.2.3.1 |
swL2QOSBandwidthControlEntryA list of information contained in swL2QOSBandwidthControlTable. SwL2QOSBandwidthControlEntry .1.3.6.1.4.1.171.11.63.11.2.3.1.1 |
swL2QOSBandwidthPortIndexIndicates the port.ro INTEGER .1.3.6.1.4.1.171.11.63.11.2.3.1.1.1 |
swL2QOSBandwidthRxRateIndicates the RX Rate(Mbit/sec) of the specifed port. A value of 1024000 means no limit.rw INTEGER .1.3.6.1.4.1.171.11.63.11.2.3.1.1.2 |
swL2QOSBandwidthTxRateIndicates the TX Rate(Mbit/sec) of the specifed port. A value of 1024000 means no limit.rw INTEGER .1.3.6.1.4.1.171.11.63.11.2.3.1.1.3 |
swL2QOSBandwidthRadiusRxRateThe Rx Rate value comes from the RADIUS server,
If an 802.1X port is authenticated, this value
will overwrite the locally configured Rx Rate.ro INTEGER .1.3.6.1.4.1.171.11.63.11.2.3.1.1.4 |
swL2QOSBandwidthRadiusTxRateThe Tx Rate value comes from the RADIUS server,
If an 802.1X port is authenticated, this value
will overwrite the locally configured Tx Rate.ro INTEGER .1.3.6.1.4.1.171.11.63.11.2.3.1.1.5 |
swL2QOSSchedulingTable. SEQUENCE OF SwL2QOSSchedulingEntry .1.3.6.1.4.1.171.11.63.11.2.3.2 |
swL2QOSSchedulingEntryA list of information contained in the swL2QOSSchedulingTable. SwL2QOSSchedulingEntry .1.3.6.1.4.1.171.11.63.11.2.3.2.1 |
swL2QOSSchedulingClassIndexIndicates the hardware queue number.ro INTEGER .1.3.6.1.4.1.171.11.63.11.2.3.2.1.1 |
swL2QOSSchedulingMaxWeightrw INTEGER .1.3.6.1.4.1.171.11.63.11.2.3.2.1.4 |
swL2QOSSchedulingMechanismIndicates the mechanism of QOS scheduling.ro Enumeration .1.3.6.1.4.1.171.11.63.11.2.3.2.1.5 |
swL2QOS8021pUserPriorityTable. SEQUENCE OF SwL2QOS8021pUserPriorityEntry .1.3.6.1.4.1.171.11.63.11.2.3.3 |
swL2QOS8021pUserPriorityEntryA list of information contained in the swL2QOS8021pUserPriorityTable. SwL2QOS8021pUserPriorityEntry .1.3.6.1.4.1.171.11.63.11.2.3.3.1 |
swL2QOS8021pUserPriorityIndexThe 802.1p user priority.ro INTEGER .1.3.6.1.4.1.171.11.63.11.2.3.3.1.1 |
swL2QOS8021pUserPriorityClassThe number of the switch's hardware priority queue. The switch has four hardware
priority queues available. They are numbered between 0 (the lowest priority)
and 3 (the highest priority).rw INTEGER .1.3.6.1.4.1.171.11.63.11.2.3.3.1.2 |
swL2QOS8021pDefaultPriorityTable. SEQUENCE OF SwL2QOS8021pDefaultPriorityEntry .1.3.6.1.4.1.171.11.63.11.2.3.4 |
swL2QOS8021pDefaultPriorityEntryA list of information contained in the swL2QOS8021pDefaultPriorityTable. SwL2QOS8021pDefaultPriorityEntry .1.3.6.1.4.1.171.11.63.11.2.3.4.1 |
swL2QOS8021pDefaultPriorityIndexIndicates the port number.ro INTEGER .1.3.6.1.4.1.171.11.63.11.2.3.4.1.1 |
swL2QOS8021pDefaultPriorityThe priority value to assign to untagged packets received by the
switch ports on the switch.rw INTEGER .1.3.6.1.4.1.171.11.63.11.2.3.4.1.2 |
swL2QOS8021pRadiusPriorityIndicates the value of 802.1p comes from RADIUS server.
If an 802.1X port is authenticated,
this value will overwrite the local configured value.ro INTEGER .1.3.6.1.4.1.171.11.63.11.2.3.4.1.3 |
swL2QOSSchedulingMechanismCtrlThis object can control QOS scheduling Mechanism.rw Enumeration .1.3.6.1.4.1.171.11.63.11.2.3.5 |
swL2TrunkMgmt OBJECT IDENTIFIER .1.3.6.1.4.1.171.11.63.11.2.4 |
swPortTrunkMaxEntriesThe max entries of the swPortTrunkTablero Integer32 .1.3.6.1.4.1.171.11.63.11.2.4.1 |
swPortTrunkMaxPortMembersThe max number of ports allowed in a trunk.ro Integer32 .1.3.6.1.4.1.171.11.63.11.2.4.2 |
swPortTrunkTableThis table specifies the port membership for each logical link. SEQUENCE OF SwPortTrunkEntry .1.3.6.1.4.1.171.11.63.11.2.4.3 |
swPortTrunkEntryA list of information that specifies which port group forms
a single logical link. SwPortTrunkEntry .1.3.6.1.4.1.171.11.63.11.2.4.3.1 |
swPortTrunkIndexThe index of logical port trunk.ro Integer32 .1.3.6.1.4.1.171.11.63.11.2.4.3.1.1 |
swPortTrunkMasterPortThe object indicates the master port number of the port trunk entry. The
first port of the trunk is implicitly configured to be the master logical
port. When using a Port Trunk, you can not configure the other ports of
the group except the master port. Their configuration must be the same as the
master port (e.g. speed, duplex, enabled/disabled, flow control, and so on).rw Integer32 .1.3.6.1.4.1.171.11.63.11.2.4.3.1.2 |
swPortTrunkPortListIndicate member ports of a logical trunk.rw PortList .1.3.6.1.4.1.171.11.63.11.2.4.3.1.3 |
swPortTrunkTypeThis object indicates the type of this entry.rw Enumeration .1.3.6.1.4.1.171.11.63.11.2.4.3.1.4 |
swPortTrunkActivePortThis object indicates the active ports of this entry.ro PortList .1.3.6.1.4.1.171.11.63.11.2.4.3.1.5 |
swPortTrunkStateThis object indicates the status of this entry.
when the state is CreatAndGo (4),the type of trunk is static (1);
when the state is CreatAndWait (5), the type of trunk is lacp(2).rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.171.11.63.11.2.4.3.1.6 |
swPortTrunkFloodingPortThe flooding port of every trunk.ro Integer32 .1.3.6.1.4.1.171.11.63.11.2.4.3.1.7 |
swL2TrunkAlgorithmThis object configures part of the packet to be examined by the
switch when selecting the egress port for transmitting
load-sharing data.rw Enumeration .1.3.6.1.4.1.171.11.63.11.2.4.4 |
swL2TrunkLACPPortTableThis table specifies which port group a set of ports (up to 8)
is formed into a single logical link. SEQUENCE OF SwL2TrunkLACPPortEntry .1.3.6.1.4.1.171.11.63.11.2.4.5 |
swL2TrunkLACPPortEntryA list of information specifies which port group a set of
ports (up to 8) is formed into a single logical link. SwL2TrunkLACPPortEntry .1.3.6.1.4.1.171.11.63.11.2.4.5.1 |
swL2TrunkLACPPortIndexThe index of the logical port LACP.ro INTEGER .1.3.6.1.4.1.171.11.63.11.2.4.5.1.1 |
swL2TrunkLACPPortStateThe state of the logical port LACP.rw Enumeration .1.3.6.1.4.1.171.11.63.11.2.4.5.1.2 |
swL2TrunkVLANTableThis table is used to manage the VLAN trunking feature of the device. SEQUENCE OF SwL2TrunkVLANEntry .1.3.6.1.4.1.171.11.63.11.2.4.6 |
swL2TrunkVLANEntryThis object is used to configure the VLAN trunking settings for each port. SwL2TrunkVLANEntry .1.3.6.1.4.1.171.11.63.11.2.4.6.1 |
swL2TrunkVLANPortThis object indicates the port being configured.ro INTEGER .1.3.6.1.4.1.171.11.63.11.2.4.6.1.1 |
swL2TrunkVLANStateThe state of the logical port LACP.rw Enumeration .1.3.6.1.4.1.171.11.63.11.2.4.6.1.2 |
swPortMirrorPackage OBJECT IDENTIFIER .1.3.6.1.4.1.171.11.63.11.2.6 |
swPortMirrorRxPortListThis object indicates the Rx port list of ports to be sniffed.rw PortList .1.3.6.1.4.1.171.11.63.11.2.6.2 |
swPortMirrorTxPortListThis object indicates the Tx port list of ports to be sniffed.rw PortList .1.3.6.1.4.1.171.11.63.11.2.6.3 |
swPortMirrorTargetPortThis object indicates the switch whose port will sniff another port.
A trunk port member cannot be configured as a target Snooping port.
The port number is the sequential (logical) number which is also
applied to the bridge MIB, etc.rw Integer32 .1.3.6.1.4.1.171.11.63.11.2.6.4 |
swPortMirrorStateThis object indicates the status of this entry.rw Enumeration .1.3.6.1.4.1.171.11.63.11.2.6.5 |
swIGMPPackage OBJECT IDENTIFIER .1.3.6.1.4.1.171.11.63.11.2.7 |
swL2IGMPMaxSupportedVlansThe maximum number of VLANs in the layer 2 IGMP control table
(swL2IGMPCtrlTable).ro INTEGER .1.3.6.1.4.1.171.11.63.11.2.7.1 |
swL2IGMPMaxIpGroupNumPerVlanThe maximum number of multicast IP groups per VLAN in the layer 2
IGMP information table (swL2IGMPQueryInfoTable).ro INTEGER .1.3.6.1.4.1.171.11.63.11.2.7.2 |
swL2IGMPCtrlTableThe table controls the VLAN's IGMP function. Its scale depends
on the current VLAN state (swL2VlanInfoStatus). If the VLAN mode is disabled, there is only one entry in the table, with index 1. If
VLAN is in Port-Based or 802.1q mode, the number of entries can
be up to 12, with an index range from 1 to 12. SEQUENCE OF SwL2IGMPCtrlEntry .1.3.6.1.4.1.171.11.63.11.2.7.3 |
swL2IGMPCtrlEntryAn entry in IGMP control table (swL2IGMPCtrlTable). The entry
is effective only when IGMP captures the switch
(swL2DevCtrlIGMPSnooping) is enabled. SwL2IGMPCtrlEntry .1.3.6.1.4.1.171.11.63.11.2.7.3.1 |
swL2IGMPCtrlVidThis object indicates the IGMP control entry's VLAN ID. If VLAN
is disabled, the VID is always 0 and cannot be changed by
management users. If VLAN is in Port-Based mode, the VID is
arranged from 1 to 12, fixed form. If VLAN is in 802.1q mode,
the VID setting can vary from 1 to 4094 by management user, and
the VID in each entry must be unique in the IGMP Control Table.ro INTEGER .1.3.6.1.4.1.171.11.63.11.2.7.3.1.1 |
swL2IGMPQueryIntervalThe frequency at which IGMP Host-Query packets are
transmitted on this switch.rw INTEGER .1.3.6.1.4.1.171.11.63.11.2.7.3.1.2 |
swL2IGMPMaxResponseTimeThe maximum query response time on this switch.rw INTEGER .1.3.6.1.4.1.171.11.63.11.2.7.3.1.3 |
swL2IGMPRobustnessThe Robustness Variable allows tuning for the expected
packet loss on a subnet. If a subnet is expected to be
lossy, the Robustness Variable may be increased. IGMP is
robust to (Robustness Variable-1) packet losses.rw INTEGER .1.3.6.1.4.1.171.11.63.11.2.7.3.1.4 |
swL2IGMPLastMemberQueryIntervalThe Last Member Query Interval is the Max Response Time
inserted into Group-Specific Queries sent in response to
Leave Group messages, and is also the amount of time between
Group-Specific Query messages.rw INTEGER .1.3.6.1.4.1.171.11.63.11.2.7.3.1.5 |
swL2IGMPHostTimeoutThe timer value for sending IGMP query packets when none was
sent by the host in the LAN. The timer works on a per-VLAN basis.
Our device will be activated to send the query message if the
timer expires. Please reference RFC2236-1997.rw INTEGER .1.3.6.1.4.1.171.11.63.11.2.7.3.1.6 |
swL2IGMPRouteTimeoutThe Router Timeout is how long a host must wait after hearing
a Query before it may send any IGMPv2 messages.rw INTEGER .1.3.6.1.4.1.171.11.63.11.2.7.3.1.7 |
swL2IGMPLeaveTimerWhen a querier receives a Leave Group message for a group that
has group members on the reception interface, it sends
Group-Specific Queries every swL2IGMPLeaveTimer to the group
being left.rw INTEGER .1.3.6.1.4.1.171.11.63.11.2.7.3.1.8 |
swL2IGMPQueryStateThis object decides if the IGMP query is enabled or disabled.rw Enumeration .1.3.6.1.4.1.171.11.63.11.2.7.3.1.9 |
swL2IGMPCurrentStateThis object indicates the current IGMP query state.ro Enumeration .1.3.6.1.4.1.171.11.63.11.2.7.3.1.10 |
swL2IGMPCtrlStateThis object indicates the status of this entry.
other (1) - This entry is currently in use but the conditions under
which it will remain so are different from each of the following
values.
disable (2) - IGMP function is disabled for this entry.
enable (3) - IGMP function is enabled for this entry.rw Enumeration .1.3.6.1.4.1.171.11.63.11.2.7.3.1.11 |
swL2IGMPFastLeaverw Enumeration .1.3.6.1.4.1.171.11.63.11.2.7.3.1.12 |
swL2IGMPDynIPMultVlanStateThis object is used to disable or enable the dynamic IP multicast feature in this VLAN.rw Enumeration .1.3.6.1.4.1.171.11.63.11.2.7.3.1.13 |
swL2IGMPDynIPMultVlanAgeThis object is used to enable or disable aging on the dynamic IP multicast entry in this VLAN.rw Enumeration .1.3.6.1.4.1.171.11.63.11.2.7.3.1.14 |
swL2IGMPQueryInfoTableThe table contains the number of current IGMP query packets which
are captured by this device, as well as the IGMP query packets
sent by the device. SEQUENCE OF SwL2IGMPQueryInfoEntry .1.3.6.1.4.1.171.11.63.11.2.7.4 |
swL2IGMPQueryInfoEntryInformation about current IGMP query information, provided that
swL2DevCtrlIGMPSnooping and swL2IGMPCtrState of associated VLAN
entry are all enabled. SwL2IGMPQueryInfoEntry .1.3.6.1.4.1.171.11.63.11.2.7.4.1 |
swL2IGMPInfoVidThis object indicates the VID of the associated IGMP info table
entry. It follows swL2IGMPCtrlVid in the associated entry of
IGMP control table (swL2IGMPCtrlTable).ro INTEGER .1.3.6.1.4.1.171.11.63.11.2.7.4.1.1 |
swL2IGMPInfoQueryCountThis object indicates the number of query packets received
since the IGMP function enabled, on a per-VLAN basis.ro INTEGER .1.3.6.1.4.1.171.11.63.11.2.7.4.1.2 |
swL2IGMPInfoTxQueryCountThis object indicates the send count of IGMP query messages, on
a per-VLAN basis. In case of the IGMP timer expiring, the switch
sends IGMP query packets to related VLAN member ports and
increment this object by 1.ro INTEGER .1.3.6.1.4.1.171.11.63.11.2.7.4.1.3 |
swL2IGMPInfoTableThe table containing current IGMP information which was captured by
this device, provided that swL2DevCtrlIGMPSnooping and
swL2IGMPCtrlState of associated VLAN entry are all enabled. Note
that the priority of IGMP table entries is lower than Filtering
Table, i.e. if there is a table hash collision between the
entries of IGMP Table and Filtering Table inside the switch H/W
address table, then Filtering Table entry overwrite the
colliding entry of IGMP Table. Also see swL2FilterMgmt description. SEQUENCE OF SwL2IGMPInfoEntry .1.3.6.1.4.1.171.11.63.11.2.7.5 |
swL2IGMPInfoEntryInformation about current IGMP information which was captured by
this device, provided that swL2DevCtrlIGMPSnooping and
swL2IGMPCtrlState of associated VLAN entry are all enabled. SwL2IGMPInfoEntry .1.3.6.1.4.1.171.11.63.11.2.7.5.1 |
swL2IGMPVidThis object indicates the VID of an individual IGMP table entry.
It shows the VID of IGMP report information captured on the
network.ro INTEGER .1.3.6.1.4.1.171.11.63.11.2.7.5.1.1 |
swL2IGMPGroupIpAddrThis object is the identify group IP address which is captured from
IGMP packet, on a per-VLAN basis.ro IpAddress .1.3.6.1.4.1.171.11.63.11.2.7.5.1.2 |
swL2IGMPMacAddrThis object identifies the MAC address which is corresponding
to swL2IGMPGroupIpAddr, on a per-VLAN basis.ro MacAddress (SNMPv2-TC) .1.3.6.1.4.1.171.11.63.11.2.7.5.1.3 |
swL2IGMPPortMapThis object indicates which ports belong to the same
multicast group, on a per-VLAN basis. Each multicast group has an
octet string to indicate the port map. The most significant
bit represents the lowest numbered port, and the least
significant bit represents the highest numbered port. Thus, each
port of the switch is represented by a single bit within the
value of this object. If that bit has a value of '1' then that
port is included in the set of ports; the port is not included
if its bit has a value of '0' (Note that the setting of the bit
corresponding to the port from which a frame is received is
irrelevant). The 4 octets represent one unit port according
to its logic port. If the unit is less than 32 ports, the other port will just fill this value with zeros.ro PortList .1.3.6.1.4.1.171.11.63.11.2.7.5.1.4 |
swL2IGMPIpGroupReportCountThis object indicates how many report packets were received by our
device corresponding with this entry that has the IGMP function enabled,
on a per-VLAN basis.ro INTEGER .1.3.6.1.4.1.171.11.63.11.2.7.5.1.5 |
swL2IGMPRouterPortTableThe information of the router port table. SEQUENCE OF SwL2IGMPRouterPortEntry .1.3.6.1.4.1.171.11.63.11.2.7.6 |
swL2IGMPRouterPortEntryThe entry of the swL2IGMPRouterPortTable. SwL2IGMPRouterPortEntry .1.3.6.1.4.1.171.11.63.11.2.7.6.1 |
swL2IGMPRouterPortVlanidThis object indicates the VLAN ID of the router port entry.ro INTEGER .1.3.6.1.4.1.171.11.63.11.2.7.6.1.1 |
swL2IGMPRouterPortVlanNameThis object indicates the VLAN name of the router port entry.ro SnmpAdminString .1.3.6.1.4.1.171.11.63.11.2.7.6.1.2 |
swL2IGMPRouterPortStaticPortListThis object indicates the static portlist of the router port entry.rw PortList .1.3.6.1.4.1.171.11.63.11.2.7.6.1.3 |
swL2IGMPRouterPortDynamicPortListThis object indicates the dynamic portlist of the router port entry.ro PortList .1.3.6.1.4.1.171.11.63.11.2.7.6.1.4 |
swL2IGMPRouterPortForbiddenPortListThis object indicates the forbidden portlist of the router port entry.rw PortList .1.3.6.1.4.1.171.11.63.11.2.7.6.1.5 |
swL2IGMPAccessAuthTableThis table is used to manage the IGMP Access Authentication
configurations of the device. SEQUENCE OF SwL2IGMPAccessAuthEntry .1.3.6.1.4.1.171.11.63.11.2.7.7 |
swL2IGMPAccessAuthEntryA list of manageable entities for IGMP Access Authentication.
The configuration is done per port. SwL2IGMPAccessAuthEntry .1.3.6.1.4.1.171.11.63.11.2.7.7.1 |
swL2IGMPAccessAuthPortThe index of the swL2IGMPAccessAuthTable.
This object corresponds to the port being configured.ro INTEGER .1.3.6.1.4.1.171.11.63.11.2.7.7.1.1 |
swL2IGMPAccessAuthStateThis object denotes the status of IGMP Access Authentication of the port.rw Enumeration .1.3.6.1.4.1.171.11.63.11.2.7.7.1.2 |
swL2IGMPMulticastVlanTableInformation about the IGMP snooping multicast VLAN table. SEQUENCE OF SwL2IGMPMulticastVlanEntry .1.3.6.1.4.1.171.11.63.11.2.7.8 |
swL2IGMPMulticastVlanEntryThe entry of swL2IGMPMulticastVlanTable. SwL2IGMPMulticastVlanEntry .1.3.6.1.4.1.171.11.63.11.2.7.8.1 |
swL2IGMPMulticastVlanidThis object indicates the VLAN ID of the IGMP snooping multicast
VLAN entry.ro INTEGER .1.3.6.1.4.1.171.11.63.11.2.7.8.1.1 |
swL2IGMPMulticastVlanNameThis object indicates the VLAN name of the IGMP snooping multicast
VLAN entry.rw DisplayString .1.3.6.1.4.1.171.11.63.11.2.7.8.1.2 |
swL2IGMPMulticastVlanSourcePortThis object indicates the port list of the source ports of the IGMP
snooping multicast VLAN. The source ports will be set as tag ports
of the VLAN entry and the IGMP control messages received from the
member ports will be forwarded to the source ports.rw PortList .1.3.6.1.4.1.171.11.63.11.2.7.8.1.3 |
swL2IGMPMulticastVlanMemberPortThis object indicates the port list of the member ports of the IGMP
snooping multicast VLAN. The source ports will be set as untagged ports
of the VLAN entry and the IGMP control messages received from the
member ports will be forwarded to the source ports.rw PortList .1.3.6.1.4.1.171.11.63.11.2.7.8.1.4 |
swL2IGMPMulticastVlanTagMemberPortThis object indicates the port list of the tag member ports of the IGMP
snooping multicast VLAN.rw PortList .1.3.6.1.4.1.171.11.63.11.2.7.8.1.5 |
swL2IGMPMulticastVlanStateThis object can be used to enable or disable the IGMP snooping multicast VLAN.rw Enumeration .1.3.6.1.4.1.171.11.63.11.2.7.8.1.6 |
swL2IGMPMulticastVlanReplaceSourceIpThe replacement source IP of this multicast VLAN.rw IpAddress .1.3.6.1.4.1.171.11.63.11.2.7.8.1.7 |
swL2IGMPMulticastVlanRowStatusThis object indicates the status of this entry.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.171.11.63.11.2.7.8.1.8 |
swL2IGMPMulticastVlanRemoveAllMcastAddrListActionThis object indicates whether to remove all the multicast address
lists from the IGMP multicast VLAN or not.rw Enumeration .1.3.6.1.4.1.171.11.63.11.2.7.8.1.9 |
swL2IGMPMulticastVlanUntagSourcePortThis object indicates the untagged member ports to add to the multicast VLAN.rw PortList .1.3.6.1.4.1.171.11.63.11.2.7.8.1.10 |
swL2IGMPMulticastVlanRemapPriorityThe priority value (0 to 7) to be associated with the data traffic
to be forwarded on the multicast VLAN.
When set to 8, the packet's original priority will be used.rw INTEGER .1.3.6.1.4.1.171.11.63.11.2.7.8.1.11 |
swL2IGMPMulticastVlanReplacePrioritySpecifies that a packet's priority will be changed by the switch
based on the remap priority. This flag will only take effect
when remap priority is set.rw Enumeration .1.3.6.1.4.1.171.11.63.11.2.7.8.1.12 |
swL2IGMPMulticastVlanGroupTableThe table containing the IGMP snooping multicast VLAN group information SEQUENCE OF SwL2IGMPMulticastVlanGroupEntry .1.3.6.1.4.1.171.11.63.11.2.7.9 |
swL2IGMPMulticastVlanGroupEntryInformation about the current IGMP snooping multicast VLAN group. SwL2IGMPMulticastVlanGroupEntry .1.3.6.1.4.1.171.11.63.11.2.7.9.1 |
swL2IGMPMulticastVlanGroupVidThis object indicates the VID of the IGMP snooping multicast VLAN group.ro INTEGER .1.3.6.1.4.1.171.11.63.11.2.7.9.1.1 |
swL2IGMPMulticastVlanGroupFromIpSpecifies the multicast address list for this VLAN.ro IpAddress .1.3.6.1.4.1.171.11.63.11.2.7.9.1.2 |
swL2IGMPMulticastVlanGroupToIpSpecifies the multicast address list for this VLAN.ro IpAddress .1.3.6.1.4.1.171.11.63.11.2.7.9.1.3 |
swL2IGMPMulticastVlanGroupStatusThis object indicates the status of this entry.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.171.11.63.11.2.7.9.1.4 |
swL2IGMPv3TableThis table contains the IGMP snooping V3 information. SEQUENCE OF SwL2IGMPv3Entry .1.3.6.1.4.1.171.11.63.11.2.7.10 |
swL2IGMPv3EntryInformation about the current IGMP snooping V3. SwL2IGMPv3Entry .1.3.6.1.4.1.171.11.63.11.2.7.10.1 |
swL2IGMPv3SourceIPAddrThis object identifies the source IP addresses from the group where they were captured from.
IGMP packets, on a per-VLAN basis.ro IpAddress .1.3.6.1.4.1.171.11.63.11.2.7.10.1.1 |
swL2IGMPv3ForwardingThis object identifies if the packets from the source IP addresses are forwarding or not.ro Enumeration .1.3.6.1.4.1.171.11.63.11.2.7.10.1.2 |
swL2IGMPv3ExpireTimerThis object identifies the leaving times of the source time.ro INTEGER .1.3.6.1.4.1.171.11.63.11.2.7.10.1.3 |
swIGMPSnoopingGroupTableThe table contains the current IGMP snooping group information captured by
the device. SEQUENCE OF SwIGMPSnoopingGroupEntry .1.3.6.1.4.1.171.11.63.11.2.7.11 |
swIGMPSnoopingGroupEntryInformation about the current IGMP snooping group information which has been captured by
the device. SwIGMPSnoopingGroupEntry .1.3.6.1.4.1.171.11.63.11.2.7.11.1 |
swIGMPSnoopingGroupVidThis object indicates the VID of the individual IGMP snooping group table entry.ro INTEGER .1.3.6.1.4.1.171.11.63.11.2.7.11.1.1 |
swIGMPSnoopingGroupGroupAddrThis object identifies the group IP address which has been captured from
the IGMP packet, on a per-VLAN basis.ro IpAddress .1.3.6.1.4.1.171.11.63.11.2.7.11.1.2 |
swIGMPSnoopingGroupSourceAddrThis object identifies the source addresses.ro IpAddress .1.3.6.1.4.1.171.11.63.11.2.7.11.1.3 |
swIGMPSnoopingGroupIncludePortMapThis object indicates the port list under INCLUDE mode.ro PortList .1.3.6.1.4.1.171.11.63.11.2.7.11.1.4 |
swIGMPSnoopingGroupExcludePortMapThis object indicates the port list under EXCLUDE mode.ro PortList .1.3.6.1.4.1.171.11.63.11.2.7.11.1.5 |
swIGMPSnoopingGroupReportCountThis object indicates how many report packets were received by our
device corresponding with this entry that has the IGMP function enabled,
on a per-group basis.ro INTEGER .1.3.6.1.4.1.171.11.63.11.2.7.11.1.6 |
swIGMPSnoopingGroupUpTimeThis object indicates how long since the group was detected.ro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.171.11.63.11.2.7.11.1.7 |
swIGMPSnoopingGroupExpiryTimeThis object indicates the time left before this group will be aged out.ro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.171.11.63.11.2.7.11.1.8 |
swIGMPSnoopingGroupRouterPortsThis object indicates the port number of the router ports.ro PortList .1.3.6.1.4.1.171.11.63.11.2.7.11.1.9 |
swL2IGMPDynIpMultMgmt OBJECT IDENTIFIER .1.3.6.1.4.1.171.11.63.11.2.7.12 |
swL2IGMPDynIPMultMaxEntryThis object specifies the maximum number of entries which can be learned by dynamic IP multicast.rw INTEGER .1.3.6.1.4.1.171.11.63.11.2.7.12.1 |
swL2IGMPSnoopingClearDynIpMult OBJECT IDENTIFIER .1.3.6.1.4.1.171.11.63.11.2.7.12.2 |
swL2IGMPSnoopingClearDynIpMultVIDThis object indicates the VLAN identifier where the data driven
entries will be removed from.rw VlanId .1.3.6.1.4.1.171.11.63.11.2.7.12.2.1 |
swL2IGMPSnoopingClearDynIpMultIPThis object indicates the IP address of the IGMP snooping group from which
the data driven entries will be removed.rw IpAddress .1.3.6.1.4.1.171.11.63.11.2.7.12.2.2 |
swL2IGMPSnoopingClearDynIpMultActionSetting this object will clear the data driven entries.
all - Remove all learned data driven groups.
VLAN - Clear all data driven entries in the VLAN specified in
swIGMPSnoopingClearDynIpMultVID.
group - Clear the group with the address specified in swL2IGMPSnoopingClearDynIpMultIP
in the VLAN specified in swIGMPSnoopingClearDynIpMultVID.rw Enumeration .1.3.6.1.4.1.171.11.63.11.2.7.12.2.3 |
swL2TrafficSegMgmt OBJECT IDENTIFIER .1.3.6.1.4.1.171.11.63.11.2.12 |
swL2TrafficSegTableThis table specifies the port just can forward traffic to the
specific port list. SEQUENCE OF SwL2TrafficSegEntry .1.3.6.1.4.1.171.11.63.11.2.12.1 |
swL2TrafficSegEntryA list of information specifies the port with its traffic
forward list. SwL2TrafficSegEntry .1.3.6.1.4.1.171.11.63.11.2.12.1.1 |
swL2TrafficSegPortThe port number of the logical port.ro INTEGER .1.3.6.1.4.1.171.11.63.11.2.12.1.1.1 |
swL2TrafficSegForwardPortsThe port list that the specific port can forward traffic.rw PortList .1.3.6.1.4.1.171.11.63.11.2.12.1.1.2 |
swL2PortSecurityMgmt OBJECT IDENTIFIER .1.3.6.1.4.1.171.11.63.11.2.15 |
swL2PortSecurityControlTableThe port security feature controls the address leaning capability and the
traffic forwarding decision. Each port can have this function enabled or disabled.
When it is enabled and a number is given said N, which allows N addresses to be
learned at this port, the first N learned addresses are locked at this port as
a static entry. When the learned address number reaches N, any incoming packet without
learned source addresses are discarded (e.g. dropped) and no more new addresses
can be learned at this port. SEQUENCE OF SwL2PortSecurityControlEntry .1.3.6.1.4.1.171.11.63.11.2.15.1 |
swL2PortSecurityControlEntryA list of information contained in the swL2PortSecurityControlTable. SwL2PortSecurityControlEntry .1.3.6.1.4.1.171.11.63.11.2.15.1.1 |
swL2PortSecurityPortIndexIndicates a secured port to lock address learning.ro INTEGER .1.3.6.1.4.1.171.11.63.11.2.15.1.1.1 |
swL2PortSecurityMaxLernAddrIndicates the allowable number of addresses to be learned at this port.rw INTEGER .1.3.6.1.4.1.171.11.63.11.2.15.1.1.2 |
swL2PortSecurityModeIndicates the mode of locking address.
In deleteOnTimeout (3) mode - the locked addresses can be aged out after the aging timer
expires. In this mode, when the locked address is aged
out, the number of addresses that can be learned has to be
increased by one.
In deleteOnReset (4) mode - never age out the locked addresses unless restarting
the system to prevent port movement or intrusion.rw Enumeration .1.3.6.1.4.1.171.11.63.11.2.15.1.1.3 |
swL2PortSecurityAdmStateIndicates an administration state of locking address.rw Enumeration .1.3.6.1.4.1.171.11.63.11.2.15.1.1.4 |
swL2PortSecurityTrapLogStateWhen enabled (2), whenever there's a new MAC that violates the pre-defined
port security configuration, a trap will be sent out and the relevant information
will be logged in the system.rw Enumeration .1.3.6.1.4.1.171.11.63.11.2.15.2 |
swL2PortSecurityDelCtrl OBJECT IDENTIFIER .1.3.6.1.4.1.171.11.63.11.2.15.3 |
swL2PortSecurityDelVlanNameIndicates the VLAN name.rw DisplayString .1.3.6.1.4.1.171.11.63.11.2.15.3.1 |
swL2PortSecurityDelPortIndicates the port. 0 means the function dose not work now.rw INTEGER .1.3.6.1.4.1.171.11.63.11.2.15.3.2 |
swL2PortSecurityDelMacAddressSpecifies the MAC address.rw MacAddress (SNMPv2-TC) .1.3.6.1.4.1.171.11.63.11.2.15.3.3 |
swL2PortSecurityDelActivityrw Enumeration .1.3.6.1.4.1.171.11.63.11.2.15.3.4 |
swL2CosMgmt OBJECT IDENTIFIER .1.3.6.1.4.1.171.11.63.11.2.17 |
swL2CosPriorityCtrl OBJECT IDENTIFIER .1.3.6.1.4.1.171.11.63.11.2.17.3 |
swL2CosPriorityTableUsed to show and configure per port priority-based QoS features on the switch. SEQUENCE OF SwL2CosPriorityEntry .1.3.6.1.4.1.171.11.63.11.2.17.3.1 |
swL2CosPriorityEntryA list of information contained in the swL2CosPriorityTable. SwL2CosPriorityEntry .1.3.6.1.4.1.171.11.63.11.2.17.3.1.1 |
swL2CosPriorityPortThe port number of CoS Priority.ro INTEGER .1.3.6.1.4.1.171.11.63.11.2.17.3.1.1.1 |
swL2CosPriorityPortPRIIndicates the port_priority state for CoS.rw Enumeration .1.3.6.1.4.1.171.11.63.11.2.17.3.1.1.2 |
swL2CosPriorityEtherPRIEnable Ethernet frame based priority.
When set ether8021p (2), enable 802.1p QoS; When set macBase (3), enable MAC-based QoS;
When set disable (1), disable Ethernet frame based priority.rw Enumeration .1.3.6.1.4.1.171.11.63.11.2.17.3.1.1.3 |
swL2CosPriorityIpPRIEnable IP priority QoS.
When set tos (2), enable TOS based QoS; When set dscp (3), enable DSCP based QoS;
When set disable (1), disable IP priority QoS.rw Enumeration .1.3.6.1.4.1.171.11.63.11.2.17.3.1.1.4 |
swL2CosPriorityNoneWhen read, it always returns invalid (2);
when write valid (1), it disables all priority in this table.rw Enumeration .1.3.6.1.4.1.171.11.63.11.2.17.3.1.1.5 |
swL2CosPortPRITableUsed to show port-to-class mappings and
map specific port to one of the hardware queues available on the switch. SEQUENCE OF SwL2CosPortPRIEntry .1.3.6.1.4.1.171.11.63.11.2.17.3.2 |
swL2CosPortPRIEntryA list of information contained in the swL2CosPortPRITable. SwL2CosPortPRIEntry .1.3.6.1.4.1.171.11.63.11.2.17.3.2.1 |
swL2CosPortPRIIndexIndicates the CoS Priority PortPRI.ro INTEGER .1.3.6.1.4.1.171.11.63.11.2.17.3.2.1.1 |
swL2CosPortPRIClassThe number of the switch's hardware priority queue. The switch has 4 hardware priority queues available.
They are numbered between 0 (the lowest priority queue) and 3 (the highest priority queue).
If you want to set one, you must have administrator privileges.
And you can set a value of 0 or 3 only, you can't set a value 1 or 2.rw INTEGER .1.3.6.1.4.1.171.11.63.11.2.17.3.2.1.2 |
swL2CosMacBasePRITableUsed to show MAC priority map to traffic class and
map the destination MAC address in incoming packet to one of the hardware queues available on the switch. SEQUENCE OF SwL2CosMacBasePRIEntry .1.3.6.1.4.1.171.11.63.11.2.17.3.3 |
swL2CosMacBasePRIEntryA list of information contained in the swL2CosMacBasePRITable. SwL2CosMacBasePRIEntry .1.3.6.1.4.1.171.11.63.11.2.17.3.3.1 |
swL2CosMacBasePRIIndexIndicates the CoS Priority MacBasePRI.ro MacAddress (SNMPv2-TC) .1.3.6.1.4.1.171.11.63.11.2.17.3.3.1.1 |
swL2CosMacBasePRIClassThe number of the switch's hardware priority queue. The switch has 4 hardware priority queues available.
They are numbered between 0 (the lowest priority queue) and 3 (the highest priority queue).
If you want to set one, you must have administrator privileges.rw INTEGER .1.3.6.1.4.1.171.11.63.11.2.17.3.3.1.2 |
swL2CosTosPRITableUsed to show TOS value to traffic class mapping and
map the TOS value in the IP header of incoming packet to one of the four hardware queues available on the switch. SEQUENCE OF SwL2CosTosPRIEntry .1.3.6.1.4.1.171.11.63.11.2.17.3.4 |
swL2CosTosPRIEntryA list of information contained in the swL2CosTosPRITable. SwL2CosTosPRIEntry .1.3.6.1.4.1.171.11.63.11.2.17.3.4.1 |
swL2CosTosPRIIndexIndicates the CoS Priority TosPRI.ro INTEGER .1.3.6.1.4.1.171.11.63.11.2.17.3.4.1.1 |
swL2CosTosPRIClassThe number of the switch's hardware priority queue. The switch has 4 hardware priority queues available.
They are numbered between 0 (the lowest priority queue) and 3 (the highest priority queue).
If you want to set one, you must have administrator privileges.rw INTEGER .1.3.6.1.4.1.171.11.63.11.2.17.3.4.1.2 |
swL2CosDscpPRITableUsed to show DSCP value to traffic class mapping and
map the DSCP value in the IP header of incoming packet to one of the hardware queues available on the switch. SEQUENCE OF SwL2CosDscpPRIEntry .1.3.6.1.4.1.171.11.63.11.2.17.3.5 |
swL2CosDscpPRIEntryA list of information contained in the swL2CosDscpPRITable. SwL2CosDscpPRIEntry .1.3.6.1.4.1.171.11.63.11.2.17.3.5.1 |
swL2CosDscpPRIIndexIndicates the CoS Priority DscpPRI.ro INTEGER .1.3.6.1.4.1.171.11.63.11.2.17.3.5.1.1 |
swL2CosDscpPRIClassThe number of the switch's hardware priority queue. The switch has 4 hardware priority queues available.
They are numbered between 0 (the lowest priority queue) and 3 (the highest priority queue).
If you want to set one, you must have administrator privileges.rw INTEGER .1.3.6.1.4.1.171.11.63.11.2.17.3.5.1.2 |
swL2DhcpRelayMgmt OBJECT IDENTIFIER .1.3.6.1.4.1.171.11.63.11.2.18 |
swL2DhcpRelayStateThis object indicates whether the DHCP relay function is enabled or
disabled.rwobsolete Enumeration .1.3.6.1.4.1.171.11.63.11.2.18.1 |
swL2DhcpRelayHopCountThis object indicates the maximum number of router hops that
the DHCP packets can cross.rwobsolete INTEGER .1.3.6.1.4.1.171.11.63.11.2.18.2 |
swL2DhcpRelayTimeThresholdThis object indicates the minimum time in seconds within which
the switch must relay the DHCP request. If this time is
exceeded, the switch will drop the DHCP packet.rwobsolete INTEGER .1.3.6.1.4.1.171.11.63.11.2.18.3 |
swL2DhcpRelayOption82StateThis object indicates DHCP relay agent information option 82
function is enabled or disabled.rwobsolete Enumeration .1.3.6.1.4.1.171.11.63.11.2.18.4 |
swL2DhcpRelayOption82CheckThis object indicates the checking mechanism of DHCP relay agent
information option 82 is enabled or disabled.rwobsolete Enumeration .1.3.6.1.4.1.171.11.63.11.2.18.5 |
swL2DhcpRelayOption82PolicyThis object indicates the reforwarding policy of DHCP relay agent
information option 82.
replace (1) - Replace the exiting option 82 field in messages.
drop (2) - Discard messages with existing option 82 field.
keep (3) - Retain the existing option 82 field in messages.rwobsolete Enumeration .1.3.6.1.4.1.171.11.63.11.2.18.6 |
swL2DhcpRelayCtrlTableThis table specifies the IP address as a destination to forward
(relay) DHCP packets to.obsolete SEQUENCE OF SwL2DhcpRelayCtrlEntry .1.3.6.1.4.1.171.11.63.11.2.18.7 |
swL2DhcpRelayCtrlEntryA list of information specifies the IP address as a destination
to forward (relay) DHCP packets to.obsolete SwL2DhcpRelayCtrlEntry .1.3.6.1.4.1.171.11.63.11.2.18.7.1 |
swL2DhcpRelayCtrlInterfaceNameThe name of the IP interface.roobsolete DisplayString .1.3.6.1.4.1.171.11.63.11.2.18.7.1.1 |
swL2DhcpRelayCtrlServerThe DHCP server IP address.ro IpAddress .1.3.6.1.4.1.171.11.63.11.2.18.7.1.2 |
swL2DhcpRelayCtrlStateThis object indicates the status of this entry.
other (1) - This entry is currently in use but the conditions
under which it will remain so are different from each of
the following values.
invalid (2) - Writing this value to the object, and then the
corresponding entry will be removed from the table.
valid (3) - This entry resides in the table.rwobsolete Enumeration .1.3.6.1.4.1.171.11.63.11.2.18.7.1.3 |
swL2MgmtMIBTraps OBJECT IDENTIFIER .1.3.6.1.4.1.171.11.63.11.2.20 |
swL2MgmtMIBTrapPrefix OBJECT IDENTIFIER .1.3.6.1.4.1.171.11.63.11.2.20.0 |
swL2PortSecurityViolationTrapWhen the port_security trap is enabled, if there's a new MAC that violates the pre-defined
port security configuration, a trap will be sent out. NOTIFICATION-TYPE .1.3.6.1.4.1.171.11.63.11.2.20.0.1 |
swL2macNotificationThis trap indicates the MAC address variations in the address table. NOTIFICATION-TYPE .1.3.6.1.4.1.171.11.63.11.2.20.0.2 |
swL2FloodMacDetectedTrapIf theres a new flooding MAC is detected, a trap will be sent out. NOTIFICATION-TYPE .1.3.6.1.4.1.171.11.63.11.2.20.0.3 |
swL2PortLoopOccurredThe trap is sent when a Port loop occurs. NOTIFICATION-TYPE .1.3.6.1.4.1.171.11.63.11.2.20.0.4 |
swL2PortLoopRestartThe trap is sent when a Port loop restarts after the interval time. NOTIFICATION-TYPE .1.3.6.1.4.1.171.11.63.11.2.20.0.5 |
swl2PortSecurityBindings OBJECT IDENTIFIER .1.3.6.1.4.1.171.11.63.11.2.20.1 |
swL2PortSecurityViolationMacThis object indicates the MAC address that violates the port security configuration.ro MacAddress (SNMPv2-TC) .1.3.6.1.4.1.171.11.63.11.2.20.1.1 |
swl2NotificationBindings OBJECT IDENTIFIER .1.3.6.1.4.1.171.11.63.11.2.20.2 |
swL2macNotifyInfoThis object indicates the last time reboot information.ro OCTET STRING .1.3.6.1.4.1.171.11.63.11.2.20.2.1 |
swL2FloodMacDetectedMacVidThis object indicates the VID of the flooding MAC.ro INTEGER .1.3.6.1.4.1.171.11.63.11.2.20.2.2 |
swL2FloodMacDetectedMacAddressThis object indicates the MAC address of the flooding MACro MacAddress (SNMPv2-TC) .1.3.6.1.4.1.171.11.63.11.2.20.2.3 |
swL2LoopDetectMgmt OBJECT IDENTIFIER .1.3.6.1.4.1.171.11.63.11.2.21 |
swL2LoopDetectCtrl OBJECT IDENTIFIER .1.3.6.1.4.1.171.11.63.11.2.21.1 |
swL2LoopDetectAdminStateThis object indicates the loopback detection status for the system.rw Enumeration .1.3.6.1.4.1.171.11.63.11.2.21.1.1 |
swL2LoopDetectIntervalThis object indicates the interval value, the range is from 1 to 32767 seconds.rw INTEGER .1.3.6.1.4.1.171.11.63.11.2.21.1.2 |
swL2LoopDetectRecoverTimeThis object indicates the recover time, the range is from 60 to 1000000.
The value of 0 disables the recover function.rw INTEGER .1.3.6.1.4.1.171.11.63.11.2.21.1.3 |
swL2LoopDetectTrapModeThis object indicates the loopback detection trap mode for the system.rw Enumeration .1.3.6.1.4.1.171.11.63.11.2.21.1.5 |
swL2LoopDetectPortMgmt OBJECT IDENTIFIER .1.3.6.1.4.1.171.11.63.11.2.21.2 |
swL2LoopDetectPortTableThe table specifies the loopback detection function specified by port. SEQUENCE OF SwL2LoopDetectPortEntry .1.3.6.1.4.1.171.11.63.11.2.21.2.1 |
swL2LoopDetectPortEntryThe table specifies the loopback detection function specified by port. SwL2LoopDetectPortEntry .1.3.6.1.4.1.171.11.63.11.2.21.2.1.1 |
swL2LoopDetectPortIndexThis object indicates the module's port number. The range is from 1 to
the maximum port number specified in the modulero INTEGER .1.3.6.1.4.1.171.11.63.11.2.21.2.1.1.1 |
swL2LoopDetectPortStateThis object indicates the loopback detection function state on the port.rw Enumeration .1.3.6.1.4.1.171.11.63.11.2.21.2.1.1.2 |
swL2LoopDetectPortLoopStatusThis object indicates the port status.ro Enumeration .1.3.6.1.4.1.171.11.63.11.2.21.2.1.1.4 |
swL2MultiFilter OBJECT IDENTIFIER .1.3.6.1.4.1.171.11.63.11.2.22 |
swL2McastFilterTableA table that contains information about the multicast filter address. SEQUENCE OF SwL2McastFilterEntry .1.3.6.1.4.1.171.11.63.11.2.22.2 |
swL2McastFilterEntryA list of multicast filter mode information for each profile ID. SwL2McastFilterEntry .1.3.6.1.4.1.171.11.63.11.2.22.2.1 |
swL2McastFilterProfileIndexindex for each profilero INTEGER .1.3.6.1.4.1.171.11.63.11.2.22.2.1.1 |
swL2McastFilterProfileNameThe multicast filter description.rw DisplayString .1.3.6.1.4.1.171.11.63.11.2.22.2.1.2 |
swL2McastFilterAddOrDelStateThe control multicast filter address.rw Enumeration .1.3.6.1.4.1.171.11.63.11.2.22.2.1.3 |
swL2McastFilterGroupListThe multicast filter address group list.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.171.11.63.11.2.22.2.1.4 |
swL2McastFilterStatusThis object indicates the status of this entry.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.171.11.63.11.2.22.2.1.5 |
swL2McastFilterPortTableA table that is used to bind port to profile ID. SEQUENCE OF SwL2McastFilterPortEntry .1.3.6.1.4.1.171.11.63.11.2.22.3 |
swL2McastFilterPortEntryA list of information that is used to bind port to profile ID. SwL2McastFilterPortEntry .1.3.6.1.4.1.171.11.63.11.2.22.3.1 |
swL2McastFilterPortGroupPortIndexThe port index.ro INTEGER .1.3.6.1.4.1.171.11.63.11.2.22.3.1.1 |
swL2McastFilterPortProfileAddOrDelStateThe control multicast filter profile.rw Enumeration .1.3.6.1.4.1.171.11.63.11.2.22.3.1.2 |
swL2McastFilterPortProfileIDThis object indicates the profile ID of this entry.
When read, it is always 0.
When set, 0 can not be set.rw INTEGER .1.3.6.1.4.1.171.11.63.11.2.22.3.1.3 |
swL2McastFilterPortMaxGroupTableA table that contains information about the max group number based on port. SEQUENCE OF SwL2McastFilterPortMaxGroupEntry .1.3.6.1.4.1.171.11.63.11.2.22.4 |
swL2McastFilterPortMaxGroupEntryA list of max group number information for each port. SwL2McastFilterPortMaxGroupEntry .1.3.6.1.4.1.171.11.63.11.2.22.4.1 |
swL2McastFilterPortMaxGroupPortIndexThe port index.ro INTEGER .1.3.6.1.4.1.171.11.63.11.2.22.4.1.1 |
swL2McastFilterPortMaxGroupThe max group numbers. The default is 256.rw INTEGER .1.3.6.1.4.1.171.11.63.11.2.22.4.1.2 |
swL2McastFilterPortInfoTableA table that contains information about all of the multicast groups for the ports. SEQUENCE OF SwL2McastFilterPortInfoEntry .1.3.6.1.4.1.171.11.63.11.2.22.5 |
swL2McastFilterPortInfoEntryA list of information about all of the multicast groups for each port. SwL2McastFilterPortInfoEntry .1.3.6.1.4.1.171.11.63.11.2.22.5.1 |
swL2McastFilterPortInfoPortIndexThe port index.ro INTEGER .1.3.6.1.4.1.171.11.63.11.2.22.5.1.1 |
swL2McastFilterPortInfoProfileNameThe multicast filter address profile Name.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.171.11.63.11.2.22.5.1.2 |
swL2VlanMgmt OBJECT IDENTIFIER .1.3.6.1.4.1.171.11.63.11.2.23 |
swL2VlanAdvertisementTableA table containing the advertisement state for each
VLAN configured into the device by (local or
network) management. SEQUENCE OF SwL2VlanAdvertisementEntry .1.3.6.1.4.1.171.11.63.11.2.23.1 |
swL2VlanAdvertisementEntryThe advertisement state for each VLAN configured
into the device. SwL2VlanAdvertisementEntry .1.3.6.1.4.1.171.11.63.11.2.23.1.1 |
swL2VlanIndexThe VLAN-ID or other identifier referring to this VLAN.ro INTEGER .1.3.6.1.4.1.171.11.63.11.2.23.1.1.1 |
swL2VlanNameAn administratively assigned string, which may be used
to identify the VLAN.ro DisplayString .1.3.6.1.4.1.171.11.63.11.2.23.1.1.2 |
swL2VlanAdvertiseStateThis object indicates the advertise status of this VLAN entry.rw Enumeration .1.3.6.1.4.1.171.11.63.11.2.23.1.1.3 |
swL2VlanMultiplyMgmt OBJECT IDENTIFIER .1.3.6.1.4.1.171.11.63.11.2.23.2 |
swL2VlanMultiplyVlanListThis object specifies the VLAN ID List.rw DisplayString .1.3.6.1.4.1.171.11.63.11.2.23.2.1 |
swL2VlanMultiplyAdvertisementThis object specifies the advertisement state.rw Enumeration .1.3.6.1.4.1.171.11.63.11.2.23.2.2 |
swL2VlanMultiplyPortListSpecifies the port list.rw PortList .1.3.6.1.4.1.171.11.63.11.2.23.2.3 |
swL2VlanMultiplyPortListActionSpecifies the action for the port list which specified
by swL2VlanMultiplyPortList.rw Enumeration .1.3.6.1.4.1.171.11.63.11.2.23.2.4 |
swL2VlanMultiplyActionSpecifies the action for VLANs.
other: no action.
create: the VLANs specified by swL2VlanMultiplyVlanList
would be created at a time.
configure: the VLANs specified by swL2VlanMultiplyVlanList
would be configured at a time.
delete: the VLANs specified by swL2VlanMultiplyVlanList
would be deleted at a time.rw Enumeration .1.3.6.1.4.1.171.11.63.11.2.23.2.5 |
swL2DhcpLocalRelayMgmt OBJECT IDENTIFIER .1.3.6.1.4.1.171.11.63.11.2.24 |
swL2DhcpLocalRelayStateThis object indicates the status of the DHCP local relay
function of the switch.rw Enumeration .1.3.6.1.4.1.171.11.63.11.2.24.1 |
swL2DhcpLocalRelayVLANTableThis table is used to manage the DHCP local relay status
for each VLAN. SEQUENCE OF SwL2DhcpLocalRelayVLANEntry .1.3.6.1.4.1.171.11.63.11.2.24.2 |
swL2DhcpLocalRelayVLANEntryThis object lists the current VLANs in the switch and their
corresponding DHCP local relay status. SwL2DhcpLocalRelayVLANEntry .1.3.6.1.4.1.171.11.63.11.2.24.2.1 |
swL2DhcpLocalRelayVLANIDThis object shows the VIDs of the current VLANS in the switch.ro INTEGER .1.3.6.1.4.1.171.11.63.11.2.24.2.1.1 |
swL2DhcpLocalRelayVLANStateThis object indicates the status of the DHCP relay function
of the VLAN.rw Enumeration .1.3.6.1.4.1.171.11.63.11.2.24.2.1.2 |
swL2FloodMAC OBJECT IDENTIFIER .1.3.6.1.4.1.171.11.63.11.2.25 |
swL2FloodMACMgmt OBJECT IDENTIFIER .1.3.6.1.4.1.171.11.63.11.2.25.1 |
swL2FloodMACGlobalSettings OBJECT IDENTIFIER .1.3.6.1.4.1.171.11.63.11.2.25.1.1 |
swL2FloodMACStateThis object indicates the status of Flooding MAC function.rw Enumeration .1.3.6.1.4.1.171.11.63.11.2.25.1.1.1 |
swL2FloodMACLogStateThis object indicates whether logs are generated when a flooding MAC is detected.rw Enumeration .1.3.6.1.4.1.171.11.63.11.2.25.1.1.2 |
swL2FloodMACTrapStateThis object indicates whether traps are generated when a flooding MAC is detected.rw Enumeration .1.3.6.1.4.1.171.11.63.11.2.25.1.1.3 |
swL2FloodMACClearFDBWhen set to start(2), this object will clear the entries of swL2FloodMACFDBTable.
After the device finishes clearing the entries, it will return to its default value, no-action(1).
Setting this object to no-action(1) will not have any effect.rw Enumeration .1.3.6.1.4.1.171.11.63.11.2.25.1.1.4 |
swL2FloodMACAutoFDBCtrlTableA table containing a list of configured IP addresses to which the Auto FDB function
will discover the corresponding VLAN, MAC address and port and have a corresponding
static FDB entry created automatically. SEQUENCE OF SwL2FloodMACAutoFDBCtrlEntry .1.3.6.1.4.1.171.11.63.11.2.25.1.2 |
swL2FloodMACAutoFDBCtrlEntryInformation containing the configured Auto FDB IP address. SwL2FloodMACAutoFDBCtrlEntry .1.3.6.1.4.1.171.11.63.11.2.25.1.2.1 |
swL2FloodMACAutoFDBIPAddressThe Auto FDB IP address. IpAddress .1.3.6.1.4.1.171.11.63.11.2.25.1.2.1.1 |
swL2FloodMACAutoFDBRowStatusThis object indicates the status of this entry.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.171.11.63.11.2.25.1.2.1.2 |
swL2FloodMACInfo OBJECT IDENTIFIER .1.3.6.1.4.1.171.11.63.11.2.25.2 |
swL2FloodMACFDBTableA table containing a list of current and historical flooding MAC entries. SEQUENCE OF SwL2FloodMACFDBEntry .1.3.6.1.4.1.171.11.63.11.2.25.2.1 |
swL2FloodMACFDBEntryInformation containing the flooding MAC address. SwL2FloodMACFDBEntry .1.3.6.1.4.1.171.11.63.11.2.25.2.1.1 |
swL2FloodMACFDBIndexThe hardware address table index of the flooding MAC entry. INTEGER .1.3.6.1.4.1.171.11.63.11.2.25.2.1.1.1 |
swL2FloodMACFDBVIDThe VLAN identifier of the flooding MAC entry. INTEGER .1.3.6.1.4.1.171.11.63.11.2.25.2.1.1.2 |
swL2FloodMACFDBMacAddressThe MAC address of the flooding MAC entry. MacAddress (SNMPv2-TC) .1.3.6.1.4.1.171.11.63.11.2.25.2.1.1.3 |
swL2FloodMACFDBStatusThe status of the flooding MAC entry. When the value is 'active', this means
the entry is currently present in the hardware address table,
otherwise, the value is 'inactive'.ro Enumeration .1.3.6.1.4.1.171.11.63.11.2.25.2.1.1.4 |
swL2FloodMACFDBTimestampA number that correlates to a relative time the entry was detected by the Flooding MAC function.ro INTEGER .1.3.6.1.4.1.171.11.63.11.2.25.2.1.1.5 |
swL2FloodMACAutoFDBTableA table containing the discovered VLAN, MAC address and port of the host
with an IP address created in swL2FloodMACAutoFDBCtrlTable. SEQUENCE OF SwL2FloodMACAutoFDBEntry .1.3.6.1.4.1.171.11.63.11.2.25.2.2 |
swL2FloodMACAutoFDBEntryInformation containing the discovered VLAN, MAC address and port of an Auto FDB entry. SwL2FloodMACAutoFDBEntry .1.3.6.1.4.1.171.11.63.11.2.25.2.2.1 |
swL2FloodMACAutoFDBVIDThe VLAN identifier of Auto FDB entry.ro INTEGER .1.3.6.1.4.1.171.11.63.11.2.25.2.2.1.1 |
swL2FloodMACAutoFDBMacAddressThe MAC address of the Auto FDB entry.ro MacAddress (SNMPv2-TC) .1.3.6.1.4.1.171.11.63.11.2.25.2.2.1.2 |
swL2FloodMACAutoFDBPortThe port number of the Auto FDB entry.ro INTEGER .1.3.6.1.4.1.171.11.63.11.2.25.2.2.1.3 |
swL2FloodMACAutoFDBTimestampA number that represents the relative time when the Auto FDB learned this entry.ro INTEGER .1.3.6.1.4.1.171.11.63.11.2.25.2.2.1.4 |