DES3010F-L2MGMT-MIB
The Structure of Common Management Information for making a trunk and IGMP related function for D-Link devices.
Main OID:
swL2MgmtMIB.1.3.6.1.4.1.171.11.63.1.1.2
241
Objects
Active
Status
5
Dependencies
Imported Objects
Objects
241 total| Object Name |
|---|
swL2MgmtMIBThe Structure of Common Management Information for
making a trunk and IGMP related function for
D-Link devices. MODULE-IDENTITY .1.3.6.1.4.1.171.11.63.1.1.2 |
swL2DevMgmt OBJECT IDENTIFIER .1.3.6.1.4.1.171.11.63.1.1.2.1 |
swL2DevInfo OBJECT IDENTIFIER .1.3.6.1.4.1.171.11.63.1.1.2.1.1 |
swL2DevInfoFrontPanelLedStatusThis object is a set of system LED indications. The two
octets is defined as system LED. The first LED is power LED. The
second LED is console LED. The other octets following
the second octets are the logical port LED (following dot1dBasePort
ordering). Every two bytes are presented to a port. The first
byte is presentd to the Link/Activity LED. The second byte is
presented to the Speed LED.
Link/Activity LED :
The most significant bit is used for blink/solid:
8 = The LED blinks.
The second significant bit is used for link status:
1 = link fail.
2 = link pass.
Speed LED :
01 = 10Mbps.
02 = 100Mbps.
03 = 1000Mbps.
The four remaining bits are currently unused and must be 0.ro OCTET STRING .1.3.6.1.4.1.171.11.63.1.1.2.1.1.5 |
swL2Module-1-TypeThis object indicates the module type.ro Enumeration .1.3.6.1.4.1.171.11.63.1.1.2.1.1.6 |
swL2Module-2-TypeThis object indicates the module type.ro Enumeration .1.3.6.1.4.1.171.11.63.1.1.2.1.1.7 |
swL2DevCtrl OBJECT IDENTIFIER .1.3.6.1.4.1.171.11.63.1.1.2.1.2 |
swL2DevCtrlSystemRebootThis object indicates the agent system reboot state. The agent always
returns other(1) when this object is read.rw Enumeration .1.3.6.1.4.1.171.11.63.1.1.2.1.2.1 |
swL2DevCtrlSystemIPThis object indicates system ip.rw IpAddress .1.3.6.1.4.1.171.11.63.1.1.2.1.2.2 |
swL2DevCtrlSubnetMaskThis object indicates system subnet mask.rw IpAddress .1.3.6.1.4.1.171.11.63.1.1.2.1.2.3 |
swL2DevCtrlDefaultGatewayThis object indicates system default gateway.rw IpAddress .1.3.6.1.4.1.171.11.63.1.1.2.1.2.4 |
swL2DevCtrlManagementVlanIdThis object controls which Vlan includes system ip. And the Vlan
should have been created.rw VlanId .1.3.6.1.4.1.171.11.63.1.1.2.1.2.5 |
swL2DevCtrlStpStateThis object can be enabled or disabled spanning tree algorithm
during runtime of the system.rw Enumeration .1.3.6.1.4.1.171.11.63.1.1.2.1.2.6 |
swL2DevCtrlIGMPSnoopingThis object indicates layer 2 Internet Group Management Protocol
(IGMP) capture function is enabled or disabled .rw Enumeration .1.3.6.1.4.1.171.11.63.1.1.2.1.2.7 |
swL2DevCtrlCleanAllStatisticCounterAs the object is set to active, all the statistic counters will be cleared.
If set to normal, do nothing.rw Enumeration .1.3.6.1.4.1.171.11.63.1.1.2.1.2.12 |
swL2DevCtrlSnmpEnableAuthenTrapsIndicates whether the SNMP entity is permitted to generate
authenticationFailure traps. The value of this object
overrides any configuration information; as such, it
provides a means whereby all authenticationFailure traps may
be disabled.
Note that it is strongly recommended that this object be
stored in non-volatile memory so that it remains constant
across re-initializations of the network management system.rw Enumeration .1.3.6.1.4.1.171.11.63.1.1.2.1.2.13 |
swL2DevCtrlRmonStateThis object can be enabled or disabled RMON.rw Enumeration .1.3.6.1.4.1.171.11.63.1.1.2.1.2.16 |
swL2DevCtrlIpAutoConfigIndicates the status of automatically getting configuration from TFTP server on devicerw Enumeration .1.3.6.1.4.1.171.11.63.1.1.2.1.2.17 |
swL2PortCtrlMulticastfilterThis object decide the multicast packets filtering mode on all port .rw Enumeration .1.3.6.1.4.1.171.11.63.1.1.2.1.2.18 |
swL2MACNotifyStateThis object can enabled or disabled MAC Notification.rw Enumeration .1.3.6.1.4.1.171.11.63.1.1.2.1.2.19 |
swL2MACNotifyHistorySizeThis object indicates the history size of variation MAC in address table.
The default value is 1 .rw INTEGER .1.3.6.1.4.1.171.11.63.1.1.2.1.2.20 |
swL2MACNotifyIntervalThis object indicates the time interval in second for trigger the MAC notify message.rw INTEGER .1.3.6.1.4.1.171.11.63.1.1.2.1.2.21 |
swL2DevCtrlVLANTrunkStateThis indicates the global state of the VLAN trunking feature of the device.rw Enumeration .1.3.6.1.4.1.171.11.63.1.1.2.1.2.22 |
swL2DevCtrlLLDPStateSpecifies the state of the LLDP function.
When this function is enabled, the switch can start to transmit
LLDP packets and receive and process the LLDP packets.
The specific function of each port will depend on the per port
LLDP setting.
For the advertisement of LLDP packets, the switch announces the
information to its neighbor through ports. For receiving
LLDP packets, the switch will learn the information from the LLDP
packets advertised from the neighbor in the neighbor table.rw Enumeration .1.3.6.1.4.1.171.11.63.1.1.2.1.2.23 |
swL2DevCtrlLLDPForwardMessageStateWhen lldp is disabled and lldp forward_message's are enabled, the
LLDP Data Unit packets received by the switch will be forwarded.rw Enumeration .1.3.6.1.4.1.171.11.63.1.1.2.1.2.24 |
swL2DevCtrlVlanIdOfFDBTblIndicates the VLAN ID to which the Dot1dTpFdbTable belongs;
The default value is DEFAULT_VLAN_ID of the system.rw VlanId .1.3.6.1.4.1.171.11.63.1.1.2.1.2.25 |
swL2CPUutilization OBJECT IDENTIFIER .1.3.6.1.4.1.171.11.63.1.1.2.1.3 |
swL2CPUutilizationIn5secTime scale is 5 seconds.The value will be between 0%(idle) and 100%
(very busy).ro Integer32 .1.3.6.1.4.1.171.11.63.1.1.2.1.3.1 |
swL2CPUutilizationIn1minTime scale is 1 minute.The value will be between 0%(idle) and 100%
(very busy).ro Integer32 .1.3.6.1.4.1.171.11.63.1.1.2.1.3.2 |
swL2CPUutilizationIn5minTime scale is 5 minute.The value will be between 0%(idle) and 100%
(very busy).ro Integer32 .1.3.6.1.4.1.171.11.63.1.1.2.1.3.3 |
swL2DevAlarm OBJECT IDENTIFIER .1.3.6.1.4.1.171.11.63.1.1.2.1.4 |
swL2DevAlarmLinkChangeThis object determines whether or not to send a trap message when the link
changes. If the object is enabled (3), the Link Change trap is sent by
the device when any of its port links change. The device does not send the
trap if this object value is disabled or in another state.rw Enumeration .1.3.6.1.4.1.171.11.63.1.1.2.1.4.3 |
swL2PortMgmt OBJECT IDENTIFIER .1.3.6.1.4.1.171.11.63.1.1.2.2 |
swL2PortInfoTableA table that contains information about every port. SEQUENCE OF SwL2PortInfoEntry .1.3.6.1.4.1.171.11.63.1.1.2.2.1 |
swL2PortInfoEntryA list of information for each port of the device. SwL2PortInfoEntry .1.3.6.1.4.1.171.11.63.1.1.2.2.1.1 |
swL2PortInfoPortIndexThis object indicates the module's port number.(1..Max port number in
the module)ro INTEGER .1.3.6.1.4.1.171.11.63.1.1.2.2.1.1.1 |
swL2PortInfoLinkStatusThis object indicates the port link status.ro Enumeration .1.3.6.1.4.1.171.11.63.1.1.2.2.1.1.4 |
swL2PortInfoNwayStatusThis object indicates the port speed and duplex mode.ro Enumeration .1.3.6.1.4.1.171.11.63.1.1.2.2.1.1.5 |
swL2PortCtrlTableA table that contains control information about every port. SEQUENCE OF SwL2PortCtrlEntry .1.3.6.1.4.1.171.11.63.1.1.2.2.2 |
swL2PortCtrlEntryA list of control information for each port of the device. SwL2PortCtrlEntry .1.3.6.1.4.1.171.11.63.1.1.2.2.2.1 |
swL2PortCtrlPortIndexThis object indicates the module's port number.(1..Max port number in
the module)ro INTEGER .1.3.6.1.4.1.171.11.63.1.1.2.2.2.1.1 |
swL2PortCtrlAdminStateThis object decide the port enabled or disabled.rw Enumeration .1.3.6.1.4.1.171.11.63.1.1.2.2.2.1.2 |
swL2PortCtrlNwayStateChose the port speed, duplex mode, and N-Way function mode.rw Enumeration .1.3.6.1.4.1.171.11.63.1.1.2.2.2.1.3 |
swL2PortCtrlFlowCtrlStateSet flow control function as enabled or disabled.rw Enumeration .1.3.6.1.4.1.171.11.63.1.1.2.2.2.1.4 |
swL2PortCtrlDescriptionThe object describe the ports in text.rw DisplayString .1.3.6.1.4.1.171.11.63.1.1.2.2.2.1.5 |
swL2PortCtrlMACNotifyStateThis object set each poet MAC notification state.rw Enumeration .1.3.6.1.4.1.171.11.63.1.1.2.2.2.1.7 |
swL2PortCtrlMDIXStateThis object controls the MDIX state of a specified port.rw Enumeration .1.3.6.1.4.1.171.11.63.1.1.2.2.2.1.10 |
swL2PortErrTableA table that contains information about Err port. SEQUENCE OF SwL2PortErrEntry .1.3.6.1.4.1.171.11.63.1.1.2.2.3 |
swL2PortErrEntryA list of information for err port of the device. SwL2PortErrEntry .1.3.6.1.4.1.171.11.63.1.1.2.2.3.1 |
swL2PortErrPortIndexThis object indicates the module's port number.(1..Max port number in
the module)ro INTEGER .1.3.6.1.4.1.171.11.63.1.1.2.2.3.1.1 |
swL2PortErrPortStateThis object decide the portstate enabled or disabled.ro Enumeration .1.3.6.1.4.1.171.11.63.1.1.2.2.3.1.2 |
swL2PortErrPortStatusThis object decide the PortStatus whether err-disabled.ro Enumeration .1.3.6.1.4.1.171.11.63.1.1.2.2.3.1.3 |
swL2PortErrPortReasonThis object decide the PortStatus STP LBD or Storm control.ro Enumeration .1.3.6.1.4.1.171.11.63.1.1.2.2.3.1.4 |
swL2PortErrDescriptionThe object describe the ports in text.ro DisplayString .1.3.6.1.4.1.171.11.63.1.1.2.2.3.1.5 |
swL2QOSMgmt OBJECT IDENTIFIER .1.3.6.1.4.1.171.11.63.1.1.2.3 |
swL2QOSBandwidthControlTable. SEQUENCE OF SwL2QOSBandwidthControlEntry .1.3.6.1.4.1.171.11.63.1.1.2.3.1 |
swL2QOSBandwidthControlEntryA list of information contained in swL2QOSBandwidthControlTable. SwL2QOSBandwidthControlEntry .1.3.6.1.4.1.171.11.63.1.1.2.3.1.1 |
swL2QOSBandwidthPortIndexIndicates the port .ro INTEGER .1.3.6.1.4.1.171.11.63.1.1.2.3.1.1.1 |
swL2QOSBandwidthRxRateIndicates RX Rate(Kbit/sec) of the specifed port.Value 1024000 means no limit.rw INTEGER .1.3.6.1.4.1.171.11.63.1.1.2.3.1.1.2 |
swL2QOSBandwidthTxRateIndicates TX Rate(Kbit/sec) of the specifed port.Value 1024000 means no limit.rw INTEGER .1.3.6.1.4.1.171.11.63.1.1.2.3.1.1.3 |
swL2QOSBandwidthRadiusRxRateThe RxRate value comes from RADIUS server,
If an 802.1X port is authenticated, this value
will overwrites the locally configured RxRate.ro INTEGER .1.3.6.1.4.1.171.11.63.1.1.2.3.1.1.4 |
swL2QOSBandwidthRadiusTxRateThe TxRate value comes from RADIUS server,
If an 802.1X port is authenticated, this value
will overwrites the locally configured TxRate.ro INTEGER .1.3.6.1.4.1.171.11.63.1.1.2.3.1.1.5 |
swL2QOSSchedulingTable. SEQUENCE OF SwL2QOSSchedulingEntry .1.3.6.1.4.1.171.11.63.1.1.2.3.2 |
swL2QOSSchedulingEntryA list of information contained in swL2QOSSchedulingTable. SwL2QOSSchedulingEntry .1.3.6.1.4.1.171.11.63.1.1.2.3.2.1 |
swL2QOSSchedulingClassIndexIndicates the hardware queue number.ro INTEGER .1.3.6.1.4.1.171.11.63.1.1.2.3.2.1.1 |
swL2QOSSchedulingMaxWeightrw INTEGER .1.3.6.1.4.1.171.11.63.1.1.2.3.2.1.4 |
swL2QOS8021pUserPriorityTable. SEQUENCE OF SwL2QOS8021pUserPriorityEntry .1.3.6.1.4.1.171.11.63.1.1.2.3.3 |
swL2QOS8021pUserPriorityEntryA list of information contained in swL2QOS8021pUserPriorityTable. SwL2QOS8021pUserPriorityEntry .1.3.6.1.4.1.171.11.63.1.1.2.3.3.1 |
swL2QOS8021pUserPriorityIndexThe 802.1p user priority .ro INTEGER .1.3.6.1.4.1.171.11.63.1.1.2.3.3.1.1 |
swL2QOS8021pUserPriorityClassThe number of the switch's hardware priority queue. The switch has four hardware
priority queues available. They are numbered between 0 (the lowest priority)
and 3 (the highest priority).rw INTEGER .1.3.6.1.4.1.171.11.63.1.1.2.3.3.1.2 |
swL2QOS8021pDefaultPriorityTable. SEQUENCE OF SwL2QOS8021pDefaultPriorityEntry .1.3.6.1.4.1.171.11.63.1.1.2.3.4 |
swL2QOS8021pDefaultPriorityEntryA list of information contained in swL2QOS8021pDefaultPriorityTable. SwL2QOS8021pDefaultPriorityEntry .1.3.6.1.4.1.171.11.63.1.1.2.3.4.1 |
swL2QOS8021pDefaultPriorityIndexIndicates the port number .ro INTEGER .1.3.6.1.4.1.171.11.63.1.1.2.3.4.1.1 |
swL2QOS8021pDefaultPriorityThe priority value to assign to untagged packets received by the
switch ports on the switch..rw INTEGER .1.3.6.1.4.1.171.11.63.1.1.2.3.4.1.2 |
swL2QOS8021pRadiusPriorityThe value of 802.1p comes from RADIUS server.
If an 802.1X port is authenticated, this value
will overwrite the local configured value.ro INTEGER .1.3.6.1.4.1.171.11.63.1.1.2.3.4.1.3 |
swL2QOSSchedulingMechanismCtrlThis object can control QOS scheduling Mechanism.rw Enumeration .1.3.6.1.4.1.171.11.63.1.1.2.3.5 |
swL2TrunkMgmt OBJECT IDENTIFIER .1.3.6.1.4.1.171.11.63.1.1.2.4 |
swPortTrunkMaxEntriesThe max entries of swPortTrunkTablero Integer32 .1.3.6.1.4.1.171.11.63.1.1.2.4.1 |
swPortTrunkMaxPortMembersThe max number of ports allowed in a trunk.ro Integer32 .1.3.6.1.4.1.171.11.63.1.1.2.4.2 |
swPortTrunkTableThis table specifies the port membership for each logical link. SEQUENCE OF SwPortTrunkEntry .1.3.6.1.4.1.171.11.63.1.1.2.4.3 |
swPortTrunkEntryA list of information specifies which ports group form
a single logical link. SwPortTrunkEntry .1.3.6.1.4.1.171.11.63.1.1.2.4.3.1 |
swPortTrunkIndexThe index of logical port trunk.ro Integer32 .1.3.6.1.4.1.171.11.63.1.1.2.4.3.1.1 |
swPortTrunkMasterPortThe object indicates the master port number of the port trunk entry.The
first port of the trunk is implicitly configured to be the master logical
port.When using Port Trunk, you can not configure the other ports of
the group except the master port. Their configuration must be same as the
master port (e.g. speed, duplex, enabled/disabled, flow control, and so on).rw Integer32 .1.3.6.1.4.1.171.11.63.1.1.2.4.3.1.2 |
swPortTrunkPortListIndicate member ports of a logical trunk.rw PortList .1.3.6.1.4.1.171.11.63.1.1.2.4.3.1.3 |
swPortTrunkTypeThis object indicates the type of this entry.rw Enumeration .1.3.6.1.4.1.171.11.63.1.1.2.4.3.1.4 |
swPortTrunkActivePortThis object indicates the active ports of this entry.ro PortList .1.3.6.1.4.1.171.11.63.1.1.2.4.3.1.5 |
swPortTrunkStateThis object indicates the status of this entry.
when the state is CreatAndGo(4),the type of trunk is static(1);
when the state is CreatAndWait(5),the type of trunk is lacp(2).rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.171.11.63.1.1.2.4.3.1.6 |
swPortTrunkFloodingPortThe flooding port of every trunk.ro Integer32 .1.3.6.1.4.1.171.11.63.1.1.2.4.3.1.7 |
swL2TrunkAlgorithmThis object configures to part of the packet examined by the
switch when selecting the egress port for transmitting
load-sharing data.rw Enumeration .1.3.6.1.4.1.171.11.63.1.1.2.4.4 |
swL2TrunkLACPPortTableThis table specifys which ports group a set of ports(up to 8)
into a single logical link. SEQUENCE OF SwL2TrunkLACPPortEntry .1.3.6.1.4.1.171.11.63.1.1.2.4.5 |
swL2TrunkLACPPortEntryA list of information specifies which ports group a set of
ports(up to 8) into a single logical link. SwL2TrunkLACPPortEntry .1.3.6.1.4.1.171.11.63.1.1.2.4.5.1 |
swL2TrunkLACPPortIndexThe index of logical port lacp.ro INTEGER .1.3.6.1.4.1.171.11.63.1.1.2.4.5.1.1 |
swL2TrunkLACPPortStateThe state of logical port lacp.rw Enumeration .1.3.6.1.4.1.171.11.63.1.1.2.4.5.1.2 |
swL2TrunkVLANTableThis table is used to manage the VLAN trunking feature of the device. SEQUENCE OF SwL2TrunkVLANEntry .1.3.6.1.4.1.171.11.63.1.1.2.4.6 |
swL2TrunkVLANEntryThis object is used to configure the VLAN trunking settings for each port. SwL2TrunkVLANEntry .1.3.6.1.4.1.171.11.63.1.1.2.4.6.1 |
swL2TrunkVLANPortThis object indicates the port being configured.ro INTEGER .1.3.6.1.4.1.171.11.63.1.1.2.4.6.1.1 |
swL2TrunkVLANStateThe state of the logical port LACP.rw Enumeration .1.3.6.1.4.1.171.11.63.1.1.2.4.6.1.2 |
swPortMirrorPackage OBJECT IDENTIFIER .1.3.6.1.4.1.171.11.63.1.1.2.6 |
swPortMirrorRxPortListThis object indicates the Rx port list of ports to be sniffed.rw PortList .1.3.6.1.4.1.171.11.63.1.1.2.6.2 |
swPortMirrorTxPortListThis object indicates the Tx port list of ports to be sniffed.rw PortList .1.3.6.1.4.1.171.11.63.1.1.2.6.3 |
swPortMirrorTargetPortThis object indicates switch which port will sniff another port.
A trunk port member cannot be configured as a target Snooping port.
The port number is the sequential (logical) number which is also
applied to bridge MIB, etc.rw Integer32 .1.3.6.1.4.1.171.11.63.1.1.2.6.4 |
swPortMirrorStateThis object indicates the status of this entry.rw Enumeration .1.3.6.1.4.1.171.11.63.1.1.2.6.5 |
swIGMPPackage OBJECT IDENTIFIER .1.3.6.1.4.1.171.11.63.1.1.2.7 |
swL2IGMPMaxSupportedVlansMaximum number of Vlans in the layer 2 IGMP control table
(swL2IGMPCtrlTable).ro INTEGER .1.3.6.1.4.1.171.11.63.1.1.2.7.1 |
swL2IGMPMaxIpGroupNumPerVlanMaximum number of multicast ip group per Vlan in the layer 2
IGMP information table (swL2IGMPQueryInfoTable).ro INTEGER .1.3.6.1.4.1.171.11.63.1.1.2.7.2 |
swL2IGMPCtrlTableThe table controls the Vlan's IGMP function. Its scale depends
on current VLAN state (swL2VlanInfoStatus). If VLAN is disabled
mode, there is only one entry in the table, with index 1. If
VLAN is in Port-Base or 802.1q mode, the number of entries can
be up to 12, with index range from 1 to 12. SEQUENCE OF SwL2IGMPCtrlEntry .1.3.6.1.4.1.171.11.63.1.1.2.7.3 |
swL2IGMPCtrlEntryThe entry in IGMP control table (swL2IGMPCtrlTable). The entry
is effective only when IGMP capture switch
(swL2DevCtrlIGMPSnooping) is enabled. SwL2IGMPCtrlEntry .1.3.6.1.4.1.171.11.63.1.1.2.7.3.1 |
swL2IGMPCtrlVidThis object indicates the IGMP control entry's VLAN id. If VLAN
is disabled, the Vid is always 0 and cannot be changed by
management users. If VLAN is in Port-Base mode, the Vid is
arranged from 1 to 12, fixed form. If VLAN is in 802.1q mode,
the Vid setting can vary from 1 to 4094 by management user, and
the Vid in each entry must be unique in the IGMP Control Table.ro INTEGER .1.3.6.1.4.1.171.11.63.1.1.2.7.3.1.1 |
swL2IGMPQueryIntervalThe frequency at which IGMP Host-Query packets are
transmitted on this switch.rw INTEGER .1.3.6.1.4.1.171.11.63.1.1.2.7.3.1.2 |
swL2IGMPMaxResponseTimeThe maximum query response time on this switch.rw INTEGER .1.3.6.1.4.1.171.11.63.1.1.2.7.3.1.3 |
swL2IGMPRobustnessThe Robustness Variable allows tuning for the expected
packet loss on a subnet. If a subnet is expected to be
lossy, the Robustness Variable may be increased. IGMP is
robust to (Robustness Variable-1) packet losses.rw INTEGER .1.3.6.1.4.1.171.11.63.1.1.2.7.3.1.4 |
swL2IGMPLastMemberQueryIntervalThe Last Member Query Interval is the Max Response Time
inserted into Group-Specific Queries sent in response to
Leave Group messages, and is also the amount of time between
Group-Specific Query messages.rw INTEGER .1.3.6.1.4.1.171.11.63.1.1.2.7.3.1.5 |
swL2IGMPHostTimeoutThe timer value for sending IGMP query packet when none was
sent by the host in the LAN. The timer works in per-VLAN basis.
Our device will be activated to send the query message if the
timer is expired. Please reference RFC2236-1997.rw INTEGER .1.3.6.1.4.1.171.11.63.1.1.2.7.3.1.6 |
swL2IGMPRouteTimeoutThe Router Timeout is how long a host must wait after hearing
a Query before it may send any IGMPv2 messages.rw INTEGER .1.3.6.1.4.1.171.11.63.1.1.2.7.3.1.7 |
swL2IGMPLeaveTimerWhen a querier receives a Leave Group message for a group that
has group members on the reception interface, it sends
Group-Specific Queries every swL2IGMPLeaveTimer to the group
being left.rw INTEGER .1.3.6.1.4.1.171.11.63.1.1.2.7.3.1.8 |
swL2IGMPQueryStateThis object decide the IGMP query enabled or disabled.rw Enumeration .1.3.6.1.4.1.171.11.63.1.1.2.7.3.1.9 |
swL2IGMPCurrentStateThis object indicates the current IGMP query state.ro Enumeration .1.3.6.1.4.1.171.11.63.1.1.2.7.3.1.10 |
swL2IGMPCtrlStateThis object indicates the status of this entry.
other(1) - this entry is currently in use but the conditions under
which it will remain so are different from each of the following
values.
disable(2) - IGMP funtion is disabled for this entry.
enable(3) - IGMP funtion is enabled for this entry.rw Enumeration .1.3.6.1.4.1.171.11.63.1.1.2.7.3.1.11 |
swL2IGMPFastLeaverw Enumeration .1.3.6.1.4.1.171.11.63.1.1.2.7.3.1.12 |
swL2IGMPQueryInfoTableThe table contains the number current IGMP query packets which
is captured by this device, as well as the IGMP query packets
sent by the device. SEQUENCE OF SwL2IGMPQueryInfoEntry .1.3.6.1.4.1.171.11.63.1.1.2.7.4 |
swL2IGMPQueryInfoEntryInformation about current IGMP query information, provided that
swL2DevCtrlIGMPSnooping and swL2IGMPCtrState of associated VLAN
entry are all enabled. SwL2IGMPQueryInfoEntry .1.3.6.1.4.1.171.11.63.1.1.2.7.4.1 |
swL2IGMPInfoVidThis object indicates the Vid of associated IGMP info table
entry. It follows swL2IGMPCtrlVid in the associated entry of
IGMP control table (swL2IGMPCtrlTable).ro INTEGER .1.3.6.1.4.1.171.11.63.1.1.2.7.4.1.1 |
swL2IGMPInfoQueryCountThis object indicates the number of query packets received
since the IGMP function enabled, in per-VLAN basis.ro INTEGER .1.3.6.1.4.1.171.11.63.1.1.2.7.4.1.2 |
swL2IGMPInfoTxQueryCountThis object indicates the send count of IGMP query messages, in
per-VLAN basis. In case of IGMP timer expiration, the switch
sends IGMP query packets to related VLAN member ports and
increment this object by 1.ro INTEGER .1.3.6.1.4.1.171.11.63.1.1.2.7.4.1.3 |
swL2IGMPInfoTableThe table containing current IGMP information which captured by
this device, provided that swL2DevCtrlIGMPSnooping and
swL2IGMPCtrlState of associated VLAN entry are all enabled. Note
that the priority of IGMP table entries is lower than Filtering
Table, i.e. if there is a table hash collision between the
entries of IGMP Table and Filtering Table inside the switch H/W
address table, then Filtering Table entry overwrite the
colliding entry of IGMP Table. See swL2FilterMgmt description
also. SEQUENCE OF SwL2IGMPInfoEntry .1.3.6.1.4.1.171.11.63.1.1.2.7.5 |
swL2IGMPInfoEntryInformation about current IGMP information which captured by
this device, provided that swL2DevCtrlIGMPSnooping and
swL2IGMPCtrlState of associated VLAN entry are all enabled. SwL2IGMPInfoEntry .1.3.6.1.4.1.171.11.63.1.1.2.7.5.1 |
swL2IGMPVidThis object indicates the Vid of individual IGMP table entry.
It shows the Vid of IGMP report information captured on
network.ro INTEGER .1.3.6.1.4.1.171.11.63.1.1.2.7.5.1.1 |
swL2IGMPGroupIpAddrThis object is identify group ip address which is captured from
IGMP packet, in per-Vlan basis.ro IpAddress .1.3.6.1.4.1.171.11.63.1.1.2.7.5.1.2 |
swL2IGMPMacAddrThis object is identify mac address which is corresponding
to swL2IGMPGroupIpAddr, in per-Vlan basis.ro MacAddress (SNMPv2-TC) .1.3.6.1.4.1.171.11.63.1.1.2.7.5.1.3 |
swL2IGMPPortMapThis object indicates which ports are belong to the same
multicast group, in per-Vlan basis. Each multicast group has a
octect string to indicate with port map. The most significant
bit represents the lowest numbered port, and the least
significant bit represents the highest numbered port. Thus, each
port of the switch is represented by a single bit within the
value of this object. If that bit has a value of '1' then that
port is included in the set of ports; the port is not included
if its bit has a value of '0'(Note that the setting of the bit
corresponding to the port from which a frame is received is
irrelevant). The 4 octets is represent one unit port according
its logic port. If the unit less 32 port, the other port don't
care just fill zero.ro PortList .1.3.6.1.4.1.171.11.63.1.1.2.7.5.1.4 |
swL2IGMPIpGroupReportCountThis object indicate how much report packet was receive by our
device corresponding with this entry from IGMP function enabled,
in per-Vlan basis.ro INTEGER .1.3.6.1.4.1.171.11.63.1.1.2.7.5.1.5 |
swL2IGMPRouterPortTableThe information of the router port table. SEQUENCE OF SwL2IGMPRouterPortEntry .1.3.6.1.4.1.171.11.63.1.1.2.7.6 |
swL2IGMPRouterPortEntryThe entry of swL2IGMPRouterPortTable. SwL2IGMPRouterPortEntry .1.3.6.1.4.1.171.11.63.1.1.2.7.6.1 |
swL2IGMPRouterPortVlanidThis object indicates the vlan id of the router port entry.ro INTEGER .1.3.6.1.4.1.171.11.63.1.1.2.7.6.1.1 |
swL2IGMPRouterPortVlanNameThis object indicates the vlan name of the router port entry.ro DisplayString .1.3.6.1.4.1.171.11.63.1.1.2.7.6.1.2 |
swL2IGMPRouterPortStaticPortListThis object indicate the static portlist of the router port entry.rw PortList .1.3.6.1.4.1.171.11.63.1.1.2.7.6.1.3 |
swL2IGMPRouterPortDynamicPortListThis object indicate the dynamic portlist of the router port entry.ro PortList .1.3.6.1.4.1.171.11.63.1.1.2.7.6.1.4 |
swL2IGMPRouterPortForbiddenPortListThis object indicate the forbidden portlist of the router port entry.rw PortList .1.3.6.1.4.1.171.11.63.1.1.2.7.6.1.5 |
swL2IGMPAccessAuthTableThis table is used to manage the IGMP Access Authentication
configurations of the device. SEQUENCE OF SwL2IGMPAccessAuthEntry .1.3.6.1.4.1.171.11.63.1.1.2.7.7 |
swL2IGMPAccessAuthEntryA list of manageable entities for IGMP Access Authentication.
The configuration is done per port. SwL2IGMPAccessAuthEntry .1.3.6.1.4.1.171.11.63.1.1.2.7.7.1 |
swL2IGMPAccessAuthPortThe index of the swL2IGMPAccessAuthTable.
This object corresponds to the port being configured.ro INTEGER .1.3.6.1.4.1.171.11.63.1.1.2.7.7.1.1 |
swL2IGMPAccessAuthStateThis object denotes the status of IGMP Access Authentication of the port.rw Enumeration .1.3.6.1.4.1.171.11.63.1.1.2.7.7.1.2 |
swL2TrafficMgmt OBJECT IDENTIFIER .1.3.6.1.4.1.171.11.63.1.1.2.11 |
swL2TrafficCtrlTableThis table specifys the storm traffic control configuration. SEQUENCE OF SwL2TrafficCtrlEntry .1.3.6.1.4.1.171.11.63.1.1.2.11.1 |
swL2TrafficCtrlEntryA list of information specifies the storm traffic control
configuration. SwL2TrafficCtrlEntry .1.3.6.1.4.1.171.11.63.1.1.2.11.1.1 |
swL2TrafficCtrlGroupIndexThe index of logical port trunk. The trunk group number depend
on the existence of unit and module.ro INTEGER .1.3.6.1.4.1.171.11.63.1.1.2.11.1.1.1 |
swL2TrafficCtrlUnitIndexIndicates ID of the unit in the devicero INTEGER .1.3.6.1.4.1.171.11.63.1.1.2.11.1.1.2 |
swL2TrafficCtrlBMStromthresholdThis object to decide how much thousand packets per second
broadcast/multicast (depend on swL2TrafficCtrlBcastStromCtrl,
swL2TrafficCtrlMcastStromCtrl or swL2TrafficCtrlUcastStromCtrl
objects whether is enabled) will active storm control. Whenever
a port reaches its configured amount of packets in the one
second time interval, the device will start dropping that type
of packet, until the time interval has expired. Once the time
interval has expired, the device will start forwarding that type
of packet.rw INTEGER .1.3.6.1.4.1.171.11.63.1.1.2.11.1.1.3 |
swL2TrafficCtrlBcastStromCtrlThis object indicates broadcast storm control function is
enabled or disabled.rw Enumeration .1.3.6.1.4.1.171.11.63.1.1.2.11.1.1.4 |
swL2TrafficCtrlMcastStromCtrlThis object indicates multicast storm control function is
enabled or disabled.rw Enumeration .1.3.6.1.4.1.171.11.63.1.1.2.11.1.1.5 |
swL2TrafficCtrlUcastStromCtrlThis object indicates destination lookup fail function is
enabled or disabled.rw Enumeration .1.3.6.1.4.1.171.11.63.1.1.2.11.1.1.6 |
swL2TrafficSegMgmt OBJECT IDENTIFIER .1.3.6.1.4.1.171.11.63.1.1.2.12 |
swL2TrafficSegTableThis table specifys the port just can forward traffic to the
specific port list. SEQUENCE OF SwL2TrafficSegEntry .1.3.6.1.4.1.171.11.63.1.1.2.12.1 |
swL2TrafficSegEntryA list of information specifies the port with its traffic
forward list. SwL2TrafficSegEntry .1.3.6.1.4.1.171.11.63.1.1.2.12.1.1 |
swL2TrafficSegPortThe port number of the logical port.ro INTEGER .1.3.6.1.4.1.171.11.63.1.1.2.12.1.1.1 |
swL2TrafficSegForwardPortsThe port list that the specific port can forward traffic.rw PortList .1.3.6.1.4.1.171.11.63.1.1.2.12.1.1.2 |
swL2PortSecurityMgmt OBJECT IDENTIFIER .1.3.6.1.4.1.171.11.63.1.1.2.15 |
swL2PortSecurityControlTableport security feature which controls the address leaning capability and the
traffic forwarding decision. Each port can have this function enabled or disabled.
When it is enabled and a number is given said N, which allows N addresses to be
learned at this port, the first N learned addresses are locked at this port as
static entry. When the learned addresses number reach N, any coming packet with
not learned source addresses are discarded (e.g. dropped) and no more new addresses
can be learned at this port. SEQUENCE OF SwL2PortSecurityControlEntry .1.3.6.1.4.1.171.11.63.1.1.2.15.1 |
swL2PortSecurityControlEntryA list of information contained in swL2PortSecurityControlTable. SwL2PortSecurityControlEntry .1.3.6.1.4.1.171.11.63.1.1.2.15.1.1 |
swL2PortSecurityPortIndexIndicates the secured port to lock address learning.ro INTEGER .1.3.6.1.4.1.171.11.63.1.1.2.15.1.1.1 |
swL2PortSecurityMaxLernAddrIndicates allowable number of addresses to be learned at this port.rw INTEGER .1.3.6.1.4.1.171.11.63.1.1.2.15.1.1.2 |
swL2PortSecurityModeIndicates the mode of locking address.
In deleteOnTimeout(3) mode - the locked addresses can be aged out after aging timer
expire. In this mode, when the locked address is aged
out, the number of address can be learned has to be
increased by one.
In deleteOnReset(4) mode - never age out the locked addresses unless restart
the system to prevent from port movement or intrusion.rw Enumeration .1.3.6.1.4.1.171.11.63.1.1.2.15.1.1.3 |
swL2PortSecurityAdmStateIndicates administration state of locking address.rw Enumeration .1.3.6.1.4.1.171.11.63.1.1.2.15.1.1.4 |
swL2PortSecurityTrapLogStatewhen enable(2),whenever there's a new MAC that violates the pre-defined
port security configuration, trap will be sent out and the relevant information
will be logged in system.rw Enumeration .1.3.6.1.4.1.171.11.63.1.1.2.15.2 |
swL2StpMgmt OBJECT IDENTIFIER .1.3.6.1.4.1.171.11.63.1.1.2.16 |
swL2StpForwardBPDUIndicates whether flooding BPDU packets when STP is disabled on devicerw Enumeration .1.3.6.1.4.1.171.11.63.1.1.2.16.1 |
swL2StpLbdIndicates whether STP loop-back prevent on the device is turned onobsolete Enumeration .1.3.6.1.4.1.171.11.63.1.1.2.16.2 |
swL2StpLbdRecoverTimeThe period of time on which STP module keeps checking the BPDU loop status,
to configure swL2StpLbdRecoverTime as 0 disables automatically recoverobsolete INTEGER .1.3.6.1.4.1.171.11.63.1.1.2.16.3 |
swL2StpPortTableA table that contains port-specific information
for the Spanning Tree Protocol. SEQUENCE OF SwL2StpPortEntry .1.3.6.1.4.1.171.11.63.1.1.2.16.4 |
swL2StpPortEntryA list of information maintained by every port
about the Spanning Tree Protocol state for that
port. SwL2StpPortEntry .1.3.6.1.4.1.171.11.63.1.1.2.16.4.1 |
swL2StpPortThe port number of the port for this entry.ro INTEGER .1.3.6.1.4.1.171.11.63.1.1.2.16.4.1.1 |
swL2StpPortLbdThe enabled/disabled status is used to Loop-back prevention attached
to this port.obsolete Enumeration .1.3.6.1.4.1.171.11.63.1.1.2.16.4.1.2 |
swL2StpPortStatusWhen the port Enable state is enabled, the port's current
state as defined by application of the Spanning Tree Protocol.
If the PortEnable is disabled, the the port status will be
no-stp-enabled(7).
If the port is in error disabled status, the port status will be err-disabled(8)ro Enumeration .1.3.6.1.4.1.171.11.63.1.1.2.16.4.1.3 |
swL2StpPortRoleWhen the port Enable state is enabled, the port's current
port role as defined by application of the Spanning Tree Protocol.
If the Port Enable state is disabled, the the port role will be
nonstp(7). If the port is in loop-back status, the port role will
be loopback(8)ro Enumeration .1.3.6.1.4.1.171.11.63.1.1.2.16.4.1.4 |
swL2StpPortFBPDUThe enabled/disabled status is used to BPDU Filtering attached
to this port.rw Enumeration .1.3.6.1.4.1.171.11.63.1.1.2.16.4.1.5 |
swL2StpPortLinkStateThis object indicates the stp port speed and duplex mode.ro Enumeration .1.3.6.1.4.1.171.11.63.1.1.2.16.4.1.6 |
swL2StpPortProtocolMigrationWhen operating in RSTP (version 2) mode, writing TRUE(1)
to this object forces this port to transmit RSTP BPDUs.
Any other operation on this object has no effect and
it always returns FALSE(2) when read.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.171.11.63.1.1.2.16.4.1.7 |
swL2StpPortAdminEdgePortThe administrative value of the Edge Port parameter. A
value of TRUE(0) indicates that this port should be
assumed as an edge-port and a value of FALSE(1) indicates
that this port should be assumed as a non-edge-port.rw Enumeration .1.3.6.1.4.1.171.11.63.1.1.2.16.4.1.8 |
swL2StpPortOperEdgePortThe operational value of the Edge Port parameter. The
object is initialized to the value of
swL2StpPortAdminEdgePort and is set FALSE on reception of
a BPDU.ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.171.11.63.1.1.2.16.4.1.9 |
swL2StpPortAdminPointToPointThe administrative point-to-point status of the LAN segment
attached to this port. A value of forceTrue(0) indicates that
this port should always be treated as if it is connected to
a point-to-point link. A value of forceFalse(1) indicates
that this port should be treated as having a shared media
connection. A value of auto(2) indicates that this port is
considered to have a point-to-point link if it is an Aggregator
and all of its members are aggregatable, or if the MAC entity
is configured for full duplex operation, either through
auto-negotiation or by management means.rw Enumeration .1.3.6.1.4.1.171.11.63.1.1.2.16.4.1.10 |
swL2StpPortOperPointToPointThe operational point-to-point status of the LAN segment
attached to this port. It indicates whether a port is
considered to have a point-to-point connection or not.
The value is determined by management or by auto-detection,
as described in the swL2StpPortAdminPointToPoint object.ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.171.11.63.1.1.2.16.4.1.11 |
swL2StpPortAdminPathCostThe administratively assigned value for the contribution
of this port to the path cost of paths towards the spanning
tree root.
Writing a value of '0' assigns the automatically calculated
default Path Cost value to the port. If the default Path
Cost is being used, this object returns '0' when read.
This complements the object swL2StpPortPathCost, which
returns the operational value of the path cost.
Issue No.: 3250R2-077
As USE_RSTP is 1:enabled, swL2StpPortPathCost is forced to be read-only.
configuration via swL2StpPortAdminPathCost.
According 802.1w, value range of swL2StpPortAdminPathCost would be expanded.
the former value range is (0..65535), the new is (0..200000000).rw Unsigned32 .1.3.6.1.4.1.171.11.63.1.1.2.16.4.1.12 |
swL2StpPortPriorityThe value of the priority field which is
contained in the first (in network byte order)
octet of the (2 octet long) Port ID. The other
octet of the Port ID is given by the value of
swL2StpPort.rw INTEGER .1.3.6.1.4.1.171.11.63.1.1.2.16.4.1.13 |
swL2STPPortStateThe enabled/disabled status is usedoop-back prevention attached
to this port.rw Enumeration .1.3.6.1.4.1.171.11.63.1.1.2.16.4.1.14 |
swL2StpPortRestrictedRoleIf TRUE causes the port not to be selected as Root Port,
even it has the best spanning tree priotiry vector.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.171.11.63.1.1.2.16.4.1.15 |
swL2StpPortRestrictedTCNIf TRUE causes the port not to propagate received topology
change notifications and topology changes to other Ports.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.171.11.63.1.1.2.16.4.1.16 |
swL2CosMgmt OBJECT IDENTIFIER .1.3.6.1.4.1.171.11.63.1.1.2.17 |
swL2CosPriorityCtrl OBJECT IDENTIFIER .1.3.6.1.4.1.171.11.63.1.1.2.17.3 |
swL2CosPriorityTableUsed to show and config per port priority-based QoS features on the switch SEQUENCE OF SwL2CosPriorityEntry .1.3.6.1.4.1.171.11.63.1.1.2.17.3.1 |
swL2CosPriorityEntryA list of information contained in swL2CosPriorityTable. SwL2CosPriorityEntry .1.3.6.1.4.1.171.11.63.1.1.2.17.3.1.1 |
swL2CosPriorityPortThe port number of CoS Priority.ro INTEGER .1.3.6.1.4.1.171.11.63.1.1.2.17.3.1.1.1 |
swL2CosPriorityPortPRIIndicates port_priority state for CoS.rw Enumeration .1.3.6.1.4.1.171.11.63.1.1.2.17.3.1.1.2 |
swL2CosPriorityEtherPRIEnable Ethernet frame based priority.
When set ether8021p(2), enable 802.1p QoS; When set macBase(3), enable MAC-based QoS;
When set disable(1), disable Ethernet frame based priority.rw Enumeration .1.3.6.1.4.1.171.11.63.1.1.2.17.3.1.1.3 |
swL2CosPriorityIpPRIEnable IP priority QoS.
When set tos(2), enable TOS based QoS; When set dscp(3), enable DSCP based QoS;
When set disable(1), disable IP priority QoS.rw Enumeration .1.3.6.1.4.1.171.11.63.1.1.2.17.3.1.1.4 |
swL2CosPriorityNonewhen read,it always return invalid(2);
when write valid(1),it disables all priority in this table.rw Enumeration .1.3.6.1.4.1.171.11.63.1.1.2.17.3.1.1.5 |
swL2CosPortPRITableUsed to show port-to-class mappings and
map specific port to one of the hardware queues available on the switch. SEQUENCE OF SwL2CosPortPRIEntry .1.3.6.1.4.1.171.11.63.1.1.2.17.3.2 |
swL2CosPortPRIEntryA list of information contained in swL2CosPortPRITable. SwL2CosPortPRIEntry .1.3.6.1.4.1.171.11.63.1.1.2.17.3.2.1 |
swL2CosPortPRIIndexIndicates CoS Priority PortPRI.ro INTEGER .1.3.6.1.4.1.171.11.63.1.1.2.17.3.2.1.1 |
swL2CosPortPRIClassThe number of the switch's hardware priority queue. The switch has 4 hardware priority queues available.
They are numbered between 0 (the lowest priority queue) and 3 (the highest priority queue).
If you want to set, You must have administrator privileges.
And you can set value only 0 or 3,you can't set value 1 or 2.rw INTEGER .1.3.6.1.4.1.171.11.63.1.1.2.17.3.2.1.2 |
swL2CosMacBasePRITableUsed to show MAC priority map to traffic class and
map the destination MAC address in incoming packet to one of the hardware queues available on the switch. SEQUENCE OF SwL2CosMacBasePRIEntry .1.3.6.1.4.1.171.11.63.1.1.2.17.3.3 |
swL2CosMacBasePRIEntryA list of information contained in swL2CosMacBasePRITable. SwL2CosMacBasePRIEntry .1.3.6.1.4.1.171.11.63.1.1.2.17.3.3.1 |
swL2CosMacBasePRIIndexIndicates CoS Priority MacBasePRI.ro MacAddress (SNMPv2-TC) .1.3.6.1.4.1.171.11.63.1.1.2.17.3.3.1.1 |
swL2CosMacBasePRIClassThe number of the switch's hardware priority queue. The switch has 4 hardware priority queues available.
They are numbered between 0 (the lowest priority queue) and 3 (the highest priority queue).
If you want to set, You must have administrator privileges.rw INTEGER .1.3.6.1.4.1.171.11.63.1.1.2.17.3.3.1.2 |
swL2CosTosPRITableUsed to show TOS value to traffic class mapping and
map the TOS value in the IP header of incoming packet to one of the four hardware queues available on the switch. SEQUENCE OF SwL2CosTosPRIEntry .1.3.6.1.4.1.171.11.63.1.1.2.17.3.4 |
swL2CosTosPRIEntryA list of information contained in swL2CosTosPRITable. SwL2CosTosPRIEntry .1.3.6.1.4.1.171.11.63.1.1.2.17.3.4.1 |
swL2CosTosPRIIndexIndicates CoS Priority TosPRI.ro INTEGER .1.3.6.1.4.1.171.11.63.1.1.2.17.3.4.1.1 |
swL2CosTosPRIClassThe number of the switch's hardware priority queue. The switch has 4 hardware priority queues available.
They are numbered between 0 (the lowest priority queue) and 3 (the highest priority queue).
If you want to set, You must have administrator privileges.rw INTEGER .1.3.6.1.4.1.171.11.63.1.1.2.17.3.4.1.2 |
swL2CosDscpPRITableUsed to show DSCP value to traffic class mapping and
map the DSCP value in the IP header of incoming packet to one of the hardware queues available on the switch. SEQUENCE OF SwL2CosDscpPRIEntry .1.3.6.1.4.1.171.11.63.1.1.2.17.3.5 |
swL2CosDscpPRIEntryA list of information contained in swL2CosDscpPRITable. SwL2CosDscpPRIEntry .1.3.6.1.4.1.171.11.63.1.1.2.17.3.5.1 |
swL2CosDscpPRIIndexIndicates CoS Priority DscpPRI.ro INTEGER .1.3.6.1.4.1.171.11.63.1.1.2.17.3.5.1.1 |
swL2CosDscpPRIClassThe number of the switch's hardware priority queue. The switch has 4 hardware priority queues available.
They are numbered between 0 (the lowest priority queue) and 3 (the highest priority queue).
If you want to set, You must have administrator privileges.rw INTEGER .1.3.6.1.4.1.171.11.63.1.1.2.17.3.5.1.2 |
swL2LoopDetectMgmt OBJECT IDENTIFIER .1.3.6.1.4.1.171.11.63.1.1.2.18 |
swL2LoopDetectCtrl OBJECT IDENTIFIER .1.3.6.1.4.1.171.11.63.1.1.2.18.1 |
swL2LoopDetectAdminStateThis object indicates the loopback detection status for the system.rw Enumeration .1.3.6.1.4.1.171.11.63.1.1.2.18.1.1 |
swL2LoopDetectIntervalThis object indicates the interval value, the range is from 1 to 32767 seconds.rw INTEGER .1.3.6.1.4.1.171.11.63.1.1.2.18.1.2 |
swL2LoopDetectRecoverTimeThis object indicates the recover time, the range is from 60 to 1000000.
The value of 0 disables the recover function.rw INTEGER .1.3.6.1.4.1.171.11.63.1.1.2.18.1.3 |
swL2LoopDetectPortMgmt OBJECT IDENTIFIER .1.3.6.1.4.1.171.11.63.1.1.2.18.2 |
swL2LoopDetectPortTableThe table specifies the loopback detection function specified by port. SEQUENCE OF SwL2LoopDetectPortEntry .1.3.6.1.4.1.171.11.63.1.1.2.18.2.1 |
swL2LoopDetectPortEntryThe table specifies the loopback detection function specified by port. SwL2LoopDetectPortEntry .1.3.6.1.4.1.171.11.63.1.1.2.18.2.1.1 |
swL2LoopDetectPortIndexThis object indicates the module's port number. The range is from 1 to
the maximum port number specified in the modulero INTEGER .1.3.6.1.4.1.171.11.63.1.1.2.18.2.1.1.1 |
swL2LoopDetectPortStateThis object indicates the loopback detection function state on the port.rw Enumeration .1.3.6.1.4.1.171.11.63.1.1.2.18.2.1.1.2 |
swL2LoopDetectPortLoopStatusThis object indicates the port status.ro Enumeration .1.3.6.1.4.1.171.11.63.1.1.2.18.2.1.1.4 |
swL2VLANMgmt OBJECT IDENTIFIER .1.3.6.1.4.1.171.11.63.1.1.2.19 |
swL2VlanTableA table containing static configuration information for
each VLAN configured into the device by (local or
network) management. All entries are permanent and will
be restored after the device is reset. SEQUENCE OF SwL2VlanEntry .1.3.6.1.4.1.171.11.63.1.1.2.19.1 |
swL2VlanEntryStatic information for a VLAN configured into the
device by (local or network) management. SwL2VlanEntry .1.3.6.1.4.1.171.11.63.1.1.2.19.1.1 |
swL2VlanIndexThe VLAN ID of the VLAN to be created. The range is 1 - 4094.ro VlanId .1.3.6.1.4.1.171.11.63.1.1.2.19.1.1.1 |
swL2VlanNameThe name of the VLAN to be displayed.ro DisplayString .1.3.6.1.4.1.171.11.63.1.1.2.19.1.1.2 |
swL2VlanTypeThe type of the VLAN to be displayed.ro Enumeration .1.3.6.1.4.1.171.11.63.1.1.2.19.1.1.3 |
swL2VlanMemberPortsA range of member ports to the VLAN.ro PortList .1.3.6.1.4.1.171.11.63.1.1.2.19.1.1.4 |
swL2VlanStaticPortsA range of static ports to the VLAN.ro PortList .1.3.6.1.4.1.171.11.63.1.1.2.19.1.1.5 |
swL2VlanUntaggedPortsSpecifies the additional ports as untagged.ro PortList .1.3.6.1.4.1.171.11.63.1.1.2.19.1.1.6 |
swL2VlanTaggedPortsSpecifies the additional ports as tagged.ro PortList .1.3.6.1.4.1.171.11.63.1.1.2.19.1.1.7 |
swL2MgmtMIBTraps OBJECT IDENTIFIER .1.3.6.1.4.1.171.11.63.1.1.2.100 |
swL2Notify OBJECT IDENTIFIER .1.3.6.1.4.1.171.11.63.1.1.2.100.1 |
swL2NotifyPrefix OBJECT IDENTIFIER .1.3.6.1.4.1.171.11.63.1.1.2.100.1.2 |
swL2NotifFirmware OBJECT IDENTIFIER .1.3.6.1.4.1.171.11.63.1.1.2.100.1.2.0 |
swL2macNotificationThis trap indicates the MAC addresses variation in address table . NOTIFICATION-TYPE .1.3.6.1.4.1.171.11.63.1.1.2.100.1.2.0.1 |
swL2PortSecurityViolationTrapWhen the port_security trap is enabled, new MAC addresses that violate
the pre-defined port security configuration will trigger trap messages
to be sent out. NOTIFICATION-TYPE .1.3.6.1.4.1.171.11.63.1.1.2.100.1.2.0.2 |
swl2NotificationBidings OBJECT IDENTIFIER .1.3.6.1.4.1.171.11.63.1.1.2.100.1.2.1 |
swL2macNotifyInfoThis object indicates the last time reboot information.ro OCTET STRING .1.3.6.1.4.1.171.11.63.1.1.2.100.1.2.1.1 |
swL2PortSecurityViolationMacThis object indicates the MAC address that violates the port security configuration.ro MacAddress (SNMPv2-TC) .1.3.6.1.4.1.171.11.63.1.1.2.100.1.2.1.2 |