DES-1228P-MIB
Detailed view of the defined objects, syntax rules, and hierarchical paths.
199
Objects
Active
Status
4
Dependencies
Imported Objects
Objects
199 total| Object Name |
|---|
d-link OBJECT IDENTIFIER .1.3.6.1.4.1.171 |
IMPORTS Unknown .1.3.6.1.4.1.171 |
dlink-products OBJECT IDENTIFIER .1.3.6.1.4.1.171.10 |
dlink-DES12XXSeriesProd OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.75 |
des-1228pa1 OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.75.3 |
swFiberInsertFiber insert trap. TRAP-TYPE .1.3.6.1.4.1.171.10.75.3.0.1 |
swFiberRemoveFiber remove trap. TRAP-TYPE .1.3.6.1.4.1.171.10.75.3.0.2 |
swFiberAbnormalRXErrorFiber abnormal rx error trap. TRAP-TYPE .1.3.6.1.4.1.171.10.75.3.0.3 |
swFiberAbnormalTXErrorFiber abnormal tx error trap. TRAP-TYPE .1.3.6.1.4.1.171.10.75.3.0.4 |
swTPAbnormalRXErrorTwisted Pair abnormal rx error trap. TRAP-TYPE .1.3.6.1.4.1.171.10.75.3.0.5 |
swTPAbnormalTXErrorTwisted Pair abnormal tx error trap. TRAP-TYPE .1.3.6.1.4.1.171.10.75.3.0.6 |
companyCommGroup OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.75.3.1 |
commSetTableA list of SNMP Set Community Entries. SEQUENCE OF CommSetEntry .1.3.6.1.4.1.171.10.75.3.1.1 |
commSetEntryA list of SNMP Set Community properties. CommSetEntry .1.3.6.1.4.1.171.10.75.3.1.1.1 |
commSetIndexAn index that uniquely identifies an entry in the
Community Table. Eight entries are currently supported.ro INTEGER .1.3.6.1.4.1.171.10.75.3.1.1.1.1 |
commSetNameThe name of this SNMP Set Community Entry.rw DisplayString .1.3.6.1.4.1.171.10.75.3.1.1.1.2 |
commSetStatusThe RowStatus for the Set Community entry.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.171.10.75.3.1.1.1.3 |
commGetTableA list of SNMP Get Community Entries. SEQUENCE OF CommGetEntry .1.3.6.1.4.1.171.10.75.3.1.2 |
commGetEntryA list of SNMP Get Community properties. CommGetEntry .1.3.6.1.4.1.171.10.75.3.1.2.1 |
commGetIndexAn index that uniquely identifies an entry in the
Community Table. Eight entries are currently supported.ro INTEGER .1.3.6.1.4.1.171.10.75.3.1.2.1.1 |
commGetNameThe name of this SNMP Get Community Entry.rw DisplayString .1.3.6.1.4.1.171.10.75.3.1.2.1.2 |
commGetStatusThe RowStatus for the Get Community entry.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.171.10.75.3.1.2.1.3 |
commTrapTableA list of SNMP Trap Community Entries. SEQUENCE OF CommTrapEntry .1.3.6.1.4.1.171.10.75.3.1.3 |
commTrapEntryA list of SNMP Trap Community properties. CommTrapEntry .1.3.6.1.4.1.171.10.75.3.1.3.1 |
commTrapIndexAn index that uniquely identifies an entry in the
Community Table. Eight entries are currently supported.ro INTEGER .1.3.6.1.4.1.171.10.75.3.1.3.1.1 |
commTrapNameThe name of this SNMP Trap Community Entry.rw DisplayString .1.3.6.1.4.1.171.10.75.3.1.3.1.2 |
commTrapIpAddressThe IP Address of this SNMP Trap Community Entry.rw IpAddress .1.3.6.1.4.1.171.10.75.3.1.3.1.3 |
commTrapSNMPBootupBootup traprw Enumeration .1.3.6.1.4.1.171.10.75.3.1.3.1.5 |
commTrapSNMPTPLinkUpDownTwisted Pair link up / link down trap.rw Enumeration .1.3.6.1.4.1.171.10.75.3.1.3.1.6 |
commTrapSNMPFiberLinkUpDownFiber link up / link down trap.rw Enumeration .1.3.6.1.4.1.171.10.75.3.1.3.1.7 |
commTrapTrapAbnormalTPRXErrorTwisted Pair abnormal receive error trap.rw Enumeration .1.3.6.1.4.1.171.10.75.3.1.3.1.9 |
commTrapTrapAbnormalTPTXErrorTwisted Pair abnormal transmit error trap.rw Enumeration .1.3.6.1.4.1.171.10.75.3.1.3.1.10 |
commTrapTrapAbnormalFiberRXErrorFiber abnormal receive error trap.rw Enumeration .1.3.6.1.4.1.171.10.75.3.1.3.1.11 |
commTrapTrapAbnormalFiberTXErrorFiber abnormal transmit error trap.rw Enumeration .1.3.6.1.4.1.171.10.75.3.1.3.1.12 |
commTrapTrapPOEPowerFailPoE POWER Failrw Enumeration .1.3.6.1.4.1.171.10.75.3.1.3.1.13 |
commTrapTrapPOEPortOvercurrentPoE port Overcurrentrw Enumeration .1.3.6.1.4.1.171.10.75.3.1.3.1.14 |
commTrapTrapPOEPortShortPoE port Shortcircuitrw Enumeration .1.3.6.1.4.1.171.10.75.3.1.3.1.15 |
commTrapStatusThe RowStatus for the Trap Community entry.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.171.10.75.3.1.3.1.16 |
companyMiscGroup OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.75.3.3 |
miscResetPhysically resets the unit - use with care. A (1) resets
the unit, a (2) does nothing.rw Enumeration .1.3.6.1.4.1.171.10.75.3.3.2 |
miscStatisticsResetResets the units statistics. A (1) resets
the unit, a (2) does nothing.rw Enumeration .1.3.6.1.4.1.171.10.75.3.3.3 |
companySpanGroup OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.75.3.4 |
spanOnOffEnable/Disable Spanning Tree. A (1) enables, a (2) disables.rw Enumeration .1.3.6.1.4.1.171.10.75.3.4.1 |
companyConfigGroup OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.75.3.11 |
configVerSwPrimaryThe software image version string.ro DisplayString .1.3.6.1.4.1.171.10.75.3.11.1 |
configVerHwChipSetThe hardware chipset version string.ro DisplayString .1.3.6.1.4.1.171.10.75.3.11.2 |
configBootTftpOperationThe tftp operation to perform downloading the boot image
to the unit. This object is used in conjunction with
configBootTftpServerIp and configBootImageFileName.rw Enumeration .1.3.6.1.4.1.171.10.75.3.11.3 |
configBootTftpServerIpThe TFTP server's IP address used for downloading the
boot image.rw IpAddress .1.3.6.1.4.1.171.10.75.3.11.4 |
configBootImageFileNameThe filename of the boot image to download.rw DisplayString .1.3.6.1.4.1.171.10.75.3.11.5 |
configPortTableA list of interface entries used for enterprise specific
configuration. The number of entries is given by the value
of ifNumber. All interface entries are assumed to be
Ethernet interafaces. SEQUENCE OF ConfigPortEntry .1.3.6.1.4.1.171.10.75.3.11.6 |
configPortEntryAn enterprise specific interface entry. ConfigPortEntry .1.3.6.1.4.1.171.10.75.3.11.6.1 |
configPortA unique value for each interface that correlates to ifIndex.
Its value ranges between 1 and the value of ifNumber.ro INTEGER .1.3.6.1.4.1.171.10.75.3.11.6.1.1 |
configPortSpeedThe port's speed desired state.rw Enumeration .1.3.6.1.4.1.171.10.75.3.11.6.1.2 |
configPortOperStatusThe port's operating speed state.ro Enumeration .1.3.6.1.4.1.171.10.75.3.11.6.1.3 |
configVLANModeDetermines the VLAN mode.rw Enumeration .1.3.6.1.4.1.171.10.75.3.11.7 |
configMirrorTableA list of the Mirror SEQUENCE OF ConfigMirrorEntry .1.3.6.1.4.1.171.10.75.3.11.8 |
configMirrorEntryA Mirror entry containing the Mirror id and mode. ConfigMirrorEntry .1.3.6.1.4.1.171.10.75.3.11.8.1 |
configMirrorIdAn index that uniquely identifies an entry in the
Mirror Table. One entries are currently supported.ro INTEGER (1) .1.3.6.1.4.1.171.10.75.3.11.8.1.1 |
configMirrorMonWhen mirroring is enabled (configMirroringMode =
ingress, egress, both), this identifies the mirroring monitoring
port. This value has a valid range of 1 to ifNumber when
enabled.rw INTEGER .1.3.6.1.4.1.171.10.75.3.11.8.1.2 |
configMirrorTXSrcWhen mirroring is enabled , this identifies the TX mirroring
source port.This value has a valid range of 1 to ifNumber
when enbaled.Each octet within this value specifies a set
of eight ports, with the first octet specifying ports 1
through 8, the second octet specifying ports 9 through 16,
etc.Within each octet, the most significant bit represents
the lowest numbered port, and the least significant bit
represents the highest numbered port. Thus, each port
of the bridge is represented by a single bit within the
value of this object. If that bit has a value of '1'
then that port is included in the set of ports; the port
is not included if its bit has a value of '0'.rw PortList .1.3.6.1.4.1.171.10.75.3.11.8.1.3 |
configMirrorRXSrcWhen mirroring is enabled , this identifies the RX mirroring
source port.This value has a valid range of 1 to ifNumber
when enbaled.Each octet within this value specifies a set
of eight ports, with the first octet specifying ports 1
through 8, the second octet specifying ports 9 through 16,
etc.Within each octet, the most significant bit represents
the lowest numbered port, and the least significant bit
represents the highest numbered port. Thus, each port
of the bridge is represented by a single bit within the
value of this object. If that bit has a value of '1'
then that port is included in the set of ports; the port
is not included if its bit has a value of '0'.rw PortList .1.3.6.1.4.1.171.10.75.3.11.8.1.4 |
configMirrorStatusThe RowStatus for the Mirror entry.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.171.10.75.3.11.8.1.5 |
configSNMPEnableEnable/Disable SNMP function. A (1) enables, a (2) disables.rw Enumeration .1.3.6.1.4.1.171.10.75.3.11.9 |
configIpAssignmentModeIndicates whether the device address is assigned by
the user (manual), or DHCP, or Others(BootP).rw Enumeration .1.3.6.1.4.1.171.10.75.3.11.12 |
configPhysAddressThe interface's address at the protocol layer
immediately 'below' the network layer in the
protocol stack. This is the physical address
for the end-station.ro MacAddress (SNMPv2-TC) .1.3.6.1.4.1.171.10.75.3.11.13 |
configPasswordAdminThe adminstrator passwordrw DisplayString .1.3.6.1.4.1.171.10.75.3.11.15 |
configIpAddressThe IP Address for the RDU box.rw IpAddress .1.3.6.1.4.1.171.10.75.3.11.16 |
configNetMaskThe network mask for the RDU box.rw IpAddress .1.3.6.1.4.1.171.10.75.3.11.17 |
configGatewayThe Gatway Address for the unit.rw IpAddress .1.3.6.1.4.1.171.10.75.3.11.18 |
configSavePhysically saves the current configuration to nvram.
- use with care.
(1) saves the configuration
(2) does nothing.rw Enumeration .1.3.6.1.4.1.171.10.75.3.11.19 |
configRestoreDefaultsRestores the configuration of the unit to the
original settings.rw Enumeration .1.3.6.1.4.1.171.10.75.3.11.22 |
configTftpServerIpAddressThe TFTP server's IP address used to upload or
download configuration file.rw IpAddress .1.3.6.1.4.1.171.10.75.3.11.32 |
configTftpServerFileNameThe filename used to store or retrieve the configuration
file from the tftp server.rw DisplayString .1.3.6.1.4.1.171.10.75.3.11.33 |
configTftpOperationThe tftp operation to perform either downloading the
configuration file to the unit or uploading the current
configuration file to the tftp server. This object is
used in conjunction with configTftpServerIpAddress
and configTftpServerFileName.rw Enumeration .1.3.6.1.4.1.171.10.75.3.11.34 |
configSafeguardEnableEnable/Disable Safeguard Engine.
D-Link Safeguard Engine is a robust and innovative technology developed by D-Link,
which will automatically throttle the impact of packet flooding into the switch's CPU.
It will keep D-Link Switches better protected from being too frequently interrupted by
malicious viruses or worm attacks.rw Enumeration .1.3.6.1.4.1.171.10.75.3.11.44 |
companyTVlanGroup OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.75.3.13 |
tvlanTableA list of the VLANs SEQUENCE OF TvlanEntry .1.3.6.1.4.1.171.10.75.3.13.1 |
tvlanEntryA VLAN entry containing the VLAN id and name. TvlanEntry .1.3.6.1.4.1.171.10.75.3.13.1.1 |
tvlanIdThe VLAN identifier. A maximum of 256 VLANs is supported.
The value must be from 1 to 4094.ro INTEGER .1.3.6.1.4.1.171.10.75.3.13.1.1.1 |
tvlanNameThe VLAN name.Length must between 1 and 20.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.171.10.75.3.13.1.1.2 |
tvlanMemberThe set of the device's member ports that belong
to the VLAN.
Each octet within the value of this object specifies a
set of eight ports, with the first octet specifying ports
1 through 8, the second octet specifying ports 9
through 16, etc. Within each octet, the most
significant bit represents the lowest numbered
port, and the least significant bit represents the
highest numbered port. Thus, each port of the
VLAN is represented by a single bit within the
value of this object. If that bit has a value of
'1' then that port is included in the set of
ports; the port is not included if its bit has a
value of '0'.rw PortList .1.3.6.1.4.1.171.10.75.3.13.1.1.3 |
tvlanUntaggedPortsIf that bit has a value of '1' the outgoing frame on the egress
port is untagged. If that bit has a value of '0' the outgoing
frame on the egress port is tagged.rw PortList .1.3.6.1.4.1.171.10.75.3.13.1.1.4 |
tvlanStatusThe status of an entry in the VLAN Table. Only a subset
of the rowstatus variables (active, createAndGo, destroy)
are available.rw Enumeration .1.3.6.1.4.1.171.10.75.3.13.1.1.5 |
tvlanManagementOnOffEnable/Disable management VLAN mechanism.rw Enumeration .1.3.6.1.4.1.171.10.75.3.13.2 |
tvlanManagementidThe management VLAN ID which allow to forward to CPU.rw INTEGER .1.3.6.1.4.1.171.10.75.3.13.3 |
tvlanPortTableA list of ports and their associated VLAN. SEQUENCE OF TvlanPortEntry .1.3.6.1.4.1.171.10.75.3.13.4 |
tvlanPortEntryInformation pertaining to an individual port regarding
to which VLAN it belongs. TvlanPortEntry .1.3.6.1.4.1.171.10.75.3.13.4.1 |
tvlanPortPortIdA port identifier that is in the range of 1 to ifNumber.ro INTEGER .1.3.6.1.4.1.171.10.75.3.13.4.1.1 |
tvlanPortVlanIdThe default VLAN identifier, PVID. The value must be from 1 to 4094.rw INTEGER .1.3.6.1.4.1.171.10.75.3.13.4.1.2 |
tvlanAsyOnOffEnable/Disable IEEE 802.1Q Asymmetric VLANrw Enumeration .1.3.6.1.4.1.171.10.75.3.13.5 |
companyPortTrunkGroup OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.75.3.14 |
portTrunkTableA list of port trunks and their associated members. SEQUENCE OF PortTrunkEntry .1.3.6.1.4.1.171.10.75.3.14.1 |
portTrunkEntryA port trunk entry containing the trunk id and trunk members. PortTrunkEntry .1.3.6.1.4.1.171.10.75.3.14.1.1 |
portTrunkIdThe port trunk identifier. The current range is from 1 to 6.ro INTEGER .1.3.6.1.4.1.171.10.75.3.14.1.1.1 |
portTrunkNameThe Trunk name.Length must between 1 and 20.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.171.10.75.3.14.1.1.2 |
portTrunkMemberA port trunk member value indicates which port is a
member of the specified trunk. Valid values are in the
range from 0 to ifNumber. A zero indicates that no port
is contained in the specifed member.
Each octet within this value specifies a set of eight
ports, with the first octet specifying ports 1 through
8, the second octet specifying ports 9 through 16, etc.
Within each octet, the most significant bit represents
the lowest numbered port, and the least significant bit
represents the highest numbered port. Thus, each port
of the bridge is represented by a single bit within the
value of this object. If that bit has a value of '1'
then that port is included in the set of ports; the port
is not included if its bit has a value of '0'.rw PortList .1.3.6.1.4.1.171.10.75.3.14.1.1.3 |
companyPoEGroup OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.75.3.15 |
poePortTableA list of SNMP Set POE Port Entries. SEQUENCE OF PoePortEntry .1.3.6.1.4.1.171.10.75.3.15.1 |
poePortEntryA list of SNMP Set POE Port properties. PoePortEntry .1.3.6.1.4.1.171.10.75.3.15.1.1 |
poeportgroupPOE Port Group Index.ro INTEGER .1.3.6.1.4.1.171.10.75.3.15.1.1.1 |
poeportidPOE Port ID Index.ro INTEGER .1.3.6.1.4.1.171.10.75.3.15.1.1.2 |
poeportpowerlimitThe value of POE Port Power Limit.rw Enumeration .1.3.6.1.4.1.171.10.75.3.15.1.1.3 |
companyStaticGroup OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.75.3.21 |
staticOnOffEnable/Disable Static MAC. Currently it doesn't support
'disabled' function.rw Enumeration .1.3.6.1.4.1.171.10.75.3.21.1 |
staticAutoLearningThe set of the device's member ports that belong
to the Static MAC auto learning enable/disable.
Each octet within the value of this object specifies a
set of eight ports, with the first octet specifying ports
1 through 8, the second octet specifying ports 9
through 16, etc. Within each octet, the most
significant bit represents the lowest numbered
port, and the least significant bit represents the
highest numbered port. Thus, each port is represented
by a single bit within the value of this object.
If that bit has a value of '1' then that port is in auto
learning enable state; the port is not in auto learning
state if its bit has a value of '0'.rw PortList .1.3.6.1.4.1.171.10.75.3.21.2 |
staticTableA list of the Static MACs SEQUENCE OF StaticEntry .1.3.6.1.4.1.171.10.75.3.21.3 |
staticEntryA Static MAC entry containing the mac and forwarding port. StaticEntry .1.3.6.1.4.1.171.10.75.3.21.3.1 |
staticIdThe Static MAC identifier. A maximum of 60 Static MACs is supported.
The value must be from 1 to 60ro INTEGER .1.3.6.1.4.1.171.10.75.3.21.3.1.1 |
staticMacThe Static MAC associated with the Id.rw MacAddress (SNMPv2-TC) .1.3.6.1.4.1.171.10.75.3.21.3.1.2 |
staticPortThe Static MAC forwarding port with the ID.rw INTEGER .1.3.6.1.4.1.171.10.75.3.21.3.1.3 |
staticVlanIDThe Static MAC VLAN ID with the ID.rw INTEGER .1.3.6.1.4.1.171.10.75.3.21.3.1.4 |
staticStatusThe status of an entry in the Static MAC Table. Only a subset
of the rowstatus variables (active, createAndGo, destroy)
are available.rw Enumeration .1.3.6.1.4.1.171.10.75.3.21.3.1.5 |
companyIgsGroup OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.75.3.22 |
igsSystem OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.75.3.22.1 |
igsStatusEnables or disables IGMP snooping in the system.rw Enumeration .1.3.6.1.4.1.171.10.75.3.22.1.2 |
igsv3ProcessingTo enable processing of IGMPv3 messages and to
operate in IGMPv3 mode, this object must be set to
enabled, when set as disabled the operation will be
in IGMPv2 mode.ro Enumeration .1.3.6.1.4.1.171.10.75.3.22.1.3 |
igsRouterPortPurgeIntervalThis is the interval (in seconds) after which a learnt
router port entry will be purged.
For each router port learnt, a 'RouterPortPurgeTimer' runs for
'RouterPortPurgeInterval'.
This timer will be restarted whenever a router control message is
received over that port. If no router control mssages are received
for 'RouterPortPurgeInterval' time, the learnt router port entry
will be purged.rw INTEGER .1.3.6.1.4.1.171.10.75.3.22.1.4 |
igsHostPortPurgeIntervalThis is the interval (in seconds) after which a learnt
host port entry will be purged.
For each host port learnt, a 'PortPurgeTimer' runs for
'HostPortPurgeInterval'.
This timer will be restarted whenever a report message from host is
received over that port. If no report mssages are received
for 'HostPortPurgeInterval' time, the learnt host entry
will be purged from the multicast group.ro INTEGER .1.3.6.1.4.1.171.10.75.3.22.1.5 |
igsReportForwardIntervalThis is the interval (in seconds) within which the next report
messages for the same multicast group will not be forwarded out.
The purpose of this timer is to avoid multiple report messages
for the same group being forwarded out. So that
unnecessary multicast packets in the network can be avoided.
The 'ReportForwardTimer' is per multicast group.
This timer is started as soon as a report message for that group is
forwarded out. Within this 'ReportForwardInterval' if
another report for the same group arrives, that report will not be
forwarded. The first report message which is received
for this group after the 'ReportForwardInterval' only will be
forwarded out.
When set as '0' , this timer will not be started and all the
report messages will be forwarded as and when they are received.ro INTEGER .1.3.6.1.4.1.171.10.75.3.22.1.6 |
igsLeaveProcessIntervalThis is the interval (in seconds) after which a Leave
message is forwarded on either router port(if present)
or on all ports of a bridge (if no router port present).
when a leave message from a host for a group is received
by the bridge, The bridge will form a group-specific query
and sends it on the port on which the leave message is
received. A timer is started by a bridge with a time interval
equal to IgsLeaveProcessInterval.
If a report message is received before above timer expires,
Leave message is dropped.Otherwise Leave message is either
forwarded on all ports of the bridge or only on router port
depending upon the case.rw INTEGER .1.3.6.1.4.1.171.10.75.3.22.1.7 |
igsMcastEntryAgeingIntervalThis is the interval (in seconds) after which the target
will be checked for Multicast data hit for the entry
This timer will be started for every (S, G) in the
control plane.ro INTEGER .1.3.6.1.4.1.171.10.75.3.22.1.8 |
igsSharedSegmentAggregationIntervalThis is the interval (in seconds) for which reports of
IGMPv3 messages on a shared segment will be aggregated
for a group.
This timer will be started only when multiple hosts are
identified on a port for the Multicast group. The timer
will be stopped when all but one host is left on the
port for the Multicast group.
This timer will be re-started on its expiry and Multicast
forwarding table will be updated.ro INTEGER .1.3.6.1.4.1.171.10.75.3.22.1.9 |
igsGblReportFwdOnAllPortsIGMP snooping module will forward reports only on router
ports by default, to enable forwarding on all other ports
the object must be set to allports.ro Enumeration .1.3.6.1.4.1.171.10.75.3.22.1.10 |
igsNextMcastFwdModeThis field describes the multicast forwarding mode that
will be used upon restart of the ISS Switch.ro Enumeration .1.3.6.1.4.1.171.10.75.3.22.1.13 |
igsQueryIntervalThe frequency at which IGMP Host-Query packets are
transmitted on this interface.rw INTEGER .1.3.6.1.4.1.171.10.75.3.22.1.14 |
igsQueryMaxResponseTimeThe maximum query response time advertised in IGMPv2
queries on this interface.rw INTEGER .1.3.6.1.4.1.171.10.75.3.22.1.15 |
igsRobustnessValueThe Robustness Variable allows tuning for the expected
packet loss on a subnet. If a subnet is expected to be
lossy, the Robustness Variable may be increased. IGMP is
robust to (Robustness Variable-1) packet losses.rw INTEGER .1.3.6.1.4.1.171.10.75.3.22.1.16 |
igsLastMembQueryIntervalThe Last Member Query Interval is the Max Response Time
inserted into Group-Specific Queries sent in response to
Leave Group messages, and is also the amount of time between
Group-Specific Query messages. This value may be tuned to
modify the leave latency of the network. A reduced value
results in reduced time to detect the loss of the last
member of a group. The value of this object is irrelevant
if igmpInterfaceVersion is 1.rw INTEGER .1.3.6.1.4.1.171.10.75.3.22.1.17 |
igsQuerierStateOnOffTo enable transmitting IGMP Query packets or to disable.rw Enumeration .1.3.6.1.4.1.171.10.75.3.22.1.18 |
igsVlan OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.75.3.22.3 |
igsVlanMcastFwdTableThis table contains VLAN based multicast forwarding
information learnt when VLAN is ENABLED in the system. SEQUENCE OF IgsVlanMcastFwdEntry .1.3.6.1.4.1.171.10.75.3.22.3.1 |
igsVlanMcastFwdEntryThis table contains VlanId, multicast group address and the
list of ports who have members for the multicast group. IgsVlanMcastFwdEntry .1.3.6.1.4.1.171.10.75.3.22.3.1.1 |
igsVlanMcastFwdVlanIdMacVlan Id pertaining to the Multicast forwarding entry. INTEGER .1.3.6.1.4.1.171.10.75.3.22.3.1.1.1 |
igsVlanMcastFwdGroupAddressMAC multicast group address. MacAddress (SNMPv2-TC) .1.3.6.1.4.1.171.10.75.3.22.3.1.1.2 |
igsVlanMcastFwdPortListMacList of ports who have members for the MAC multicast
group and the Vlan Id.ro PortList .1.3.6.1.4.1.171.10.75.3.22.3.1.1.3 |
igsVlanRouterPortListTableThis table contains list of bridge ports through which
a router, in a particular VLAN, is reachable. SEQUENCE OF IgsVlanRouterPortListEntry .1.3.6.1.4.1.171.10.75.3.22.3.3 |
igsVlanRouterPortListEntryContains VlanId of router , list of reachable
router ports. IgsVlanRouterPortListEntry .1.3.6.1.4.1.171.10.75.3.22.3.3.1 |
igsVlanRouterPortListVlanIdVlan Id of the ports through which router is reachable. INTEGER .1.3.6.1.4.1.171.10.75.3.22.3.3.1.1 |
igsVlanRouterPortListContains list of bridge ports through which a router,
in a particular VLAN, is reachable. These router ports
are learnt through control messages received from routers,
and can also be configured statically.ro PortList .1.3.6.1.4.1.171.10.75.3.22.3.3.1.2 |
igsVlanFilterTableThis table contains configuration to disable IGMP snooping
on specific Vlans. This Table is valid only when VLAN is
enabled in the system. SEQUENCE OF IgsVlanFilterEntry .1.3.6.1.4.1.171.10.75.3.22.3.4 |
igsVlanFilterEntryContains Vlan Id , Vlan Filter Status. IgsVlanFilterEntry .1.3.6.1.4.1.171.10.75.3.22.3.4.1 |
igsVlanIdVlan Id for which IGMP snooping feature is to be disabled. INTEGER .1.3.6.1.4.1.171.10.75.3.22.3.4.1.1 |
igsVlanFilterStatusWhen status is set as enabled, IGMP snooping feature
is disabled for that Vlan Id.
When status is set as disabled, the entry stands invalid.
In that case IGMP snooping feature remains enabled for
that Vlan.rw Enumeration .1.3.6.1.4.1.171.10.75.3.22.3.4.1.2 |
companyDot1xGroup OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.75.3.23 |
radius OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.75.3.23.1 |
radiusServerAddressThe IP address of the RADIUS server.rw IpAddress .1.3.6.1.4.1.171.10.75.3.23.1.1 |
radiusServerPortThe Port of the RADIUS server.rw INTEGER .1.3.6.1.4.1.171.10.75.3.23.1.2 |
radiusServerSharedSecretThe secret string which is shared between Server and Client.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.171.10.75.3.23.1.3 |
dot1xAuth OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.75.3.23.2 |
dot1xAuthSystemControlEnable/Disable Static 802.1x. A (1) enables, a (2) disables.rw Enumeration .1.3.6.1.4.1.171.10.75.3.23.2.1 |
dot1xAuthQuietPeriodThe value, in seconds, of the quietPeriod constant
currently in use by the Authenticator PAE state
machine.rw INTEGER .1.3.6.1.4.1.171.10.75.3.23.2.2 |
dot1xAuthTxPeriodThe value, in seconds, of the txPeriod constant
currently in use by the Authenticator PAE state
machine.rw INTEGER .1.3.6.1.4.1.171.10.75.3.23.2.3 |
dot1xAuthSuppTimeoutThe value, in seconds, of the suppTimeout constant
currently in use by the Backend Authentication state
machine.rw INTEGER .1.3.6.1.4.1.171.10.75.3.23.2.4 |
dot1xAuthServerTimeoutThe value, in seconds, of the serverTimeout constant
currently in use by the Backend Authentication state
machine.rw INTEGER .1.3.6.1.4.1.171.10.75.3.23.2.5 |
dot1xAuthMaxReqThe value of the maxReq constant currently in use by
the Backend Authentication state machine.rw INTEGER .1.3.6.1.4.1.171.10.75.3.23.2.6 |
dot1xAuthReAuthPeriodThe value, in seconds, of the reAuthPeriod constant
currently in use by the Reauthentication Timer state
machine.rw Unsigned32 .1.3.6.1.4.1.171.10.75.3.23.2.7 |
dot1xAuthReAuthEnabledThe enable/disable control used by the Reauthentication
Timer state machine (8.5.5.1).rw Enumeration .1.3.6.1.4.1.171.10.75.3.23.2.8 |
dot1xAuthConfigPortTableA table that contains the configuration objects for the
Authenticator PAE associated with each port.
An entry appears in this table for each port that may
authenticate access to itself. SEQUENCE OF Dot1xAuthConfigPortEntry .1.3.6.1.4.1.171.10.75.3.23.2.9 |
dot1xAuthConfigPortEntryThe configuration information for an Authenticator Port. Dot1xAuthConfigPortEntry .1.3.6.1.4.1.171.10.75.3.23.2.9.1 |
dot1xAuthConfigPortNumberA unique value for each interface that correlates to ifIndex.
Its value ranges between 1 and the value of ifNumber.ro INTEGER .1.3.6.1.4.1.171.10.75.3.23.2.9.1.1 |
dot1xAuthConfigPortControlThe current value of the controlled Port
control parameter for the Port.rw Enumeration .1.3.6.1.4.1.171.10.75.3.23.2.9.1.2 |
dot1xAuthConfigPortStatusThe current value of the controlled Port
status parameter for the Port.ro Enumeration .1.3.6.1.4.1.171.10.75.3.23.2.9.1.3 |
dot1xAuthConfigPortSessionTimeThe duration of the session in seconds.ro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.171.10.75.3.23.2.9.1.4 |
dot1xAuthConfigPortSessionUserNameThe User-Name representing the identity of the
Supplicant PAE.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.171.10.75.3.23.2.9.1.5 |
companyLLDPExtnGroup OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.75.3.24 |
lldpSysMACDigestThe system MAC Digestro DisplayString .1.3.6.1.4.1.171.10.75.3.24.1 |
lldpAntiRoguePortControlWhen LLDP anti-rogue port control is enabled , this identifies the
port control status of each port.
This value has a valid range of 1 to ifNumber
when enbaled. Each octet within this value specifies a set
of eight ports, with the first octet specifying ports 1
through 8, the second octet specifying ports 9 through 16,
etc. Within each octet, the most significant bit represents
the lowest numbered port, and the least significant bit
represents the highest numbered port. Thus, each port
of the bridge is represented by a single bit within the
value of this object. If that bit has a value of '1'
then that port is included in the set of ports; the port
is not included if its bit has a value of '0'.rw PortList .1.3.6.1.4.1.171.10.75.3.24.2 |
lldpRemOrgDefInfoTableThis table contains one or more rows per physical network
connection which advertises the organizationally defined
information.
Note that this table contains one or more rows of
organizationally defined information that is not recognized
by the local agent.
If the local system is capable of recognizing any
organizationally defined information, appropriate extension
MIBs from the organization should be used for information
retrieval. SEQUENCE OF LldpRemOrgDefInfoEntry .1.3.6.1.4.1.171.10.75.3.24.3 |
lldpRemOrgDefInfoEntryInformation about the unrecognized organizationally
defined information advertised by the remote system.
The lldpAntiRoguePortIndex is index to this table.
Entries may be created and deleted in this table by the
agent. LldpRemOrgDefInfoEntry .1.3.6.1.4.1.171.10.75.3.24.3.1 |
lldpAntiRoguePortIndexA unique value for each interface that correlates to ifIndex.
Its value ranges between 1 and the value of ifNumber.ro INTEGER .1.3.6.1.4.1.171.10.75.3.24.3.1.1 |
lldpAntiRoguePortStatusThe value represents each port's authentication status.
0: Authentication disabled.
1: Authentication enabled but not passed.
2: Authentication successful.ro Enumeration .1.3.6.1.4.1.171.10.75.3.24.3.1.2 |
lldpRemOrgDefInfoOUIThe Organizationally Unique Identifier (OUI), as defined
in IEEE std 802-2001, is a 24 bit (three octets) globally
unique assigned number referenced by various standards,
of the information received from the remote system.ro OCTET STRING .1.3.6.1.4.1.171.10.75.3.24.3.1.3 |
lldpAntiRogueKeyThe Anti Rogue Keyrw OCTET STRING .1.3.6.1.4.1.171.10.75.3.24.4 |
lldpSysConfigChecksumThe system EEPROM config checksum. Use this value to check system
config has been changed or not.ro INTEGER .1.3.6.1.4.1.171.10.75.3.24.5 |
lldpGalobalEnableEnable or disable the LLDP protocol.
(1) enables the system and (2) disables it.rw Enumeration .1.3.6.1.4.1.171.10.75.3.24.6 |
companyQoSGroup OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.75.3.26 |
qosModeSettings of Qos mode:
IEEE 802.1p QoS or DSCP QoS.rw Enumeration .1.3.6.1.4.1.171.10.75.3.26.1 |
queuingMechanismQueuing mechanism.
strictPriority(1) : Strict Priority
wrr(2) : Weighted Round Robinrw Enumeration .1.3.6.1.4.1.171.10.75.3.26.2 |
dot1pPortTableA list of 802.1p port default priority Entries. SEQUENCE OF Dot1pPortEntry .1.3.6.1.4.1.171.10.75.3.26.3 |
dot1pPortEntryA list of 802.1p port default priority priorities. Dot1pPortEntry .1.3.6.1.4.1.171.10.75.3.26.3.1 |
dot1pPortIndexA port identifier that is in the range of 1 to ifNumber.ro INTEGER .1.3.6.1.4.1.171.10.75.3.26.3.1.1 |
dot1pPortPriorityFor ingress untagged packets, the per port 'Default Priority'
setting will be applied to packets of each port to provide
port-based traffic prioritization.
For ingress tagged packets, D-Link Smart Switches will refer
to their 802.1p information and prioritize them with 4
different priority queues.rw Enumeration .1.3.6.1.4.1.171.10.75.3.26.3.1.2 |
dscpTableA list of DSCP Entries. SEQUENCE OF DscpEntry .1.3.6.1.4.1.171.10.75.3.26.4 |
dscpEntryA list of DSCP properties. DscpEntry .1.3.6.1.4.1.171.10.75.3.26.4.1 |
dscpIndexDSCP value. For ingress IP packets, the DiffServ field of IP packets
provide DSCP-based traffic prioritization information to switches.
D-Link Smart Switches will refer to the value of DiffServ filed
information and prioritize them with 4 different priority queues.ro INTEGER .1.3.6.1.4.1.171.10.75.3.26.4.1.1 |
dscpPriorityThe queuing priority mapping to DSCP value.rw Enumeration .1.3.6.1.4.1.171.10.75.3.26.4.1.2 |
companyTrafficMgmt OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.75.3.27 |
broadcastStormCtrlSettings OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.75.3.27.3 |
broadcastStormCtrlGlobalOnOffThis object indicates storm control function is enabled or disabled
for device.
When you enable broadcast storm control function, D-Link Smart
Switches will allowed you to limit the number of broadcast packets
per second going through device.rw Enumeration .1.3.6.1.4.1.171.10.75.3.27.3.1 |
broadcastStormGlobalThresholdThe threshold value in unit of thousand bytes per second for broadcast traffic of the specific port.rw Enumeration .1.3.6.1.4.1.171.10.75.3.27.3.2 |
companySecurity OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.75.3.28 |
trustedHostSettings OBJECT IDENTIFIER .1.3.6.1.4.1.171.10.75.3.28.1 |
trustedHostOnOffThis object indicates trusted host function is enabled or disabled.
When trusted host function is enabled, D-Link Smart Switches will
only allow hosts which you trust to access and control the switch.
Your local host IP Addresses must be one of the IP Addresses to
avoid disconnection.rw Enumeration .1.3.6.1.4.1.171.10.75.3.28.1.1 |
trustedHostTableA list of Trusted Host Entries. SEQUENCE OF TrustedHostEntry .1.3.6.1.4.1.171.10.75.3.28.1.2 |
trustedHostEntryA list of Trusted Host properties. TrustedHostEntry .1.3.6.1.4.1.171.10.75.3.28.1.2.1 |
trustedHostIDAn index that uniquely identifies an entry in the
Trusted Host Table. Three entries are currently supported.ro INTEGER .1.3.6.1.4.1.171.10.75.3.28.1.2.1.1 |
trustedHostIpAddressThe IP address of host you allow to access to D-Link Smart
Switch.
Your local host IP Addresses must be one of the IP Addresses
to avoid disconnection.rw IpAddress .1.3.6.1.4.1.171.10.75.3.28.1.2.1.2 |
trustedHostIpMaskUsed to mask with IP address, it allow you set a subnet as a
trusted host entry.rw IpAddress .1.3.6.1.4.1.171.10.75.3.28.1.2.1.3 |
trustedHostStatusThe status of an entry in the Trusted Host Table. Only a subset
of the rowstatus variables (active, createAndGo, destroy)
are available.rw Enumeration .1.3.6.1.4.1.171.10.75.3.28.1.2.1.4 |