DECHUB900-PTRM-MIB-V3-0
Detailed view of the defined objects, syntax rules, and hierarchical paths.
46
Objects
Active
Status
2
Dependencies
Imported Objects
Objects
46 total| Object Name |
|---|
dec OBJECT IDENTIFIER .1.3.6.1.4.1.36 |
RFC1155-SMI Unknown .1.3.6.1.4.1.36 |
ema OBJECT IDENTIFIER .1.3.6.1.4.1.36.2 |
decMIBextension OBJECT IDENTIFIER .1.3.6.1.4.1.36.2.18 |
decHub900 OBJECT IDENTIFIER .1.3.6.1.4.1.36.2.18.11 |
ptrm OBJECT IDENTIFIER .1.3.6.1.4.1.36.2.18.11.3 |
ptrmBase OBJECT IDENTIFIER .1.3.6.1.4.1.36.2.18.11.3.1 |
ptrmBaseForceSpeedThis object selects the speed at which to token ring linecard
operates. When set to notForced(1), the linecard will not be forced.
Based on the line-card its speed may change by a voting algorithm
on its lobe ports or by console selection.
Forcing the speed to 4 or 16 only applies when stand-alone;
in a hub, the ring to which the module is forced determines the
speed at which it operates.
The value of this object is maintained across power cycles
and resets.rw Enumeration .1.3.6.1.4.1.36.2.18.11.3.1.2 |
ptrmBaseSpeedIndicates the speed at which the linecard is operating.
Devices like the DECmau 900TL autobaud when they are not forced
via ptrmBaseForceSpeed and if there are no stations plugged into the
lobe ports.
Devices like the DECmau 900TH (Dtmxm) have a default speed of 16Mbps
which can also be changed via a console interface.ro Enumeration .1.3.6.1.4.1.36.2.18.11.3.1.3 |
ptrmBaseNumLobesThe number of end station lobes supported by this module.
This is the number of rows in the ptrmLobeTable. This
variable is zero for repeaters.ro INTEGER .1.3.6.1.4.1.36.2.18.11.3.1.4 |
ptrmTrunkTableDefines a table with rows for each token ring connection
not otherwise associated with an end-user 'lobe' port.
The following rows are implemented:
ptrmTrunkType Leaf VIDs Port
RingIn (1) 3.2.1.x.1 Copper Ring In
RingOut (2) 3.2.1.x.2 Copper Ring Out
HubA-1 (3) 3.2.1.x.3 Hub token ring A port 1
HubB-1 (4) 3.2.1.x.4 Hub token ring B port 1
FibreIn (5) 3.2.1.x.5 FibreRingIn
FibreOut(6) 3.2.1.x.6 FibreRingOut
HubA-2 (7) 3.2.1.x.3 Hub token ring A port 2
HubB-2 (8) 3.2.1.x.4 Hub token ring B port 2 SEQUENCE OF PtrmTrunkEntry .1.3.6.1.4.1.36.2.18.11.3.2 |
ptrmTrunkEntryA collection of trunk objects. PtrmTrunkEntry .1.3.6.1.4.1.36.2.18.11.3.2.1 |
ptrmTrunkTypeIdentifies a trunk (i.e. non-lobe) port. All token ring
modules implement all four rows defined by the ptrmTrunkType
values. If a module's configuration does not allow it to
implement the particular trunk ptrmTrunkOperStatus is
notPresent(3). For example, linecards in a hub do not have a
RingIn or RingOut port and therefore contain the value
notPreset(3) as the ptrmTrunkOperStatus for ringIn(1) and
ringOut(2) rows of the trunk table.
Linecards that do not have a fiber interface need not implement
rows FiberIn(5) and FiberOut(6).
NOTE - If a Trunk is notPresent, the rest of the values in this
table are to be ignored.ro Enumeration .1.3.6.1.4.1.36.2.18.11.3.2.1.1 |
ptrmTrunkOperStatusIndicates whether the trunk port is wrapped or inserted
into the linecard's internal ring. If the trunk port is not
implemented in the linecard's current configuration, then
this is notPresent(3). If a trunk is notPresent(3), then
the values read from all other columns of the row are
undefined.
If the port is enabled and an incompatible speed is
detected, the value of this object is 'badSpeed(4)'.
The trunk TCU is wrapped when in the badSpeed state.
When there is a change in this object, a csnmp Trap is
sent to the MAM.ro Enumeration .1.3.6.1.4.1.36.2.18.11.3.2.1.2 |
ptrmTrunkAdminStatusUsed to disable the trunk port of the linecard during
operation. When disabled, the trunk port is forced to wrap.
The value of this object is maintained across power cycles
and resets.rw Enumeration .1.3.6.1.4.1.36.2.18.11.3.2.1.3 |
ptrmTrunkMediaThe media type of the trunk port. Different module types have
different trunk connectors. If a module implements an
STP/UTP switch, this variable indicates the setting of that
switch.
linecards feature Trunk Coupling Units (TCUs) on the module for
their hub trunk connection, so they have 'media' type hubTCU(7).
Repeaters have a direct connection to the hub backplane, so
their hub trunk 'media' type is hubDirect(6).ro Enumeration .1.3.6.1.4.1.36.2.18.11.3.2.1.4 |
ptrmTrunkAutoWrapEnableThe value of the physical Auto Wrap Enable (AWE) switch for the
trunk port. AWE is provided only for RingIn and RingOut trunks.
AWE should be set ON for connection to DEChub token
ring linecards. It should be set OFF when an
IBM 8228 or equivalent 'dumb' linecard is connected. It MUST be
physically switched to ON when no cable is inserted into
the RI port, in order to cause RI to wrap.
This value of this object is notApplicable(3) for hub trunks.
The value of this object is maintained across power cycles
and resets.rw Enumeration .1.3.6.1.4.1.36.2.18.11.3.2.1.5 |
ptrmTrunkAutoPartitionStatusIndicates whether the trunk port has been auto-partitioned.
When autopartitioned(2) a trunk is automatically wrapped.ro Enumeration .1.3.6.1.4.1.36.2.18.11.3.2.1.6 |
ptrmTrunkDetectedSpeedIndicates the speed detected on the incoming data pair.
invalid(1) indicates that a valid token ring speed was not
detected. notApplicable(4) indicates that the trunk port
does not implement speed detect. Hub trunks do not detect
speed.ro Enumeration .1.3.6.1.4.1.36.2.18.11.3.2.1.7 |
ptrmTrunkPhantomDriveIndicates the state of the RingIn port's phantom current drive
and return detect circuits. It is notApplicable(1) on all other
trunk types. The noDrive(2) status indicates RingIn is not
driving phantom current. driveReceive(3) is the normal case
where an active linecard drives phantom current on RingIn and
it is returned correctly from the upstream linecard. wireFault(4)
indicates the linecard is driving phantom current but the current
is not returned correctly, due to either an open or short
circuit.ro Enumeration .1.3.6.1.4.1.36.2.18.11.3.2.1.8 |
ptrmTrunkPhantomDetectIndicates the state of the incoming phantom current detect circuit
for the RingIn/RingOut Trunk. It is notApplicable(1) to all other
trunk types.ro Enumeration .1.3.6.1.4.1.36.2.18.11.3.2.1.9 |
ptrmLobeTableA table with entries to manage individual end station lobe
ports of the linecard. SEQUENCE OF PtrmLobeEntry .1.3.6.1.4.1.36.2.18.11.3.3 |
ptrmLobeEntryA lobe entry. PtrmLobeEntry .1.3.6.1.4.1.36.2.18.11.3.3.1 |
ptrmLobeIndexPort number for the lobe, as it appears externally to the
user, i.e. 1 for the port labeled '1'.ro INTEGER .1.3.6.1.4.1.36.2.18.11.3.3.1.1 |
ptrmLobeOperStatusIndicates whether the lobe port is wrapped or inserted
into the linecard's internal ring. If the lobe port is not
implemented in the linecard's current configuration the value
of this object is notPresent(3). If a lobe is notPresent(3)
then the values of other variables in the row are undefined.
If the port is enabled and an incompatible speed is
detected, this variable becomes 'badSpeed(4)'.
The lobe TCU is wrapped when in the badSpeed state.
When there is a change in this object, a CSNMP trap is sent to
the MAM.ro Enumeration .1.3.6.1.4.1.36.2.18.11.3.3.1.2 |
ptrmLobeAdminStatusUsed to disable the lobe port during network troubleshooting.
If set to disabled(2), the lobe port is forced to wrap.
This object must be set to enabled(1) for normal operation.
The value of this object is maintained across power cycles
and resets.rw Enumeration .1.3.6.1.4.1.36.2.18.11.3.3.1.3 |
ptrmLobeMediaThe media type of the lobe port. Different module types have
different lobe connectors. If a module implements an
STP/UTP switch for lobes, this variable indicates the setting
of that switch.ro Enumeration .1.3.6.1.4.1.36.2.18.11.3.3.1.4 |
ptrmLobeAutoWrapEnableSoftware configuration variable set by network management.
Auto Wrap Enabled (AWE) should be set on(1) for connection to
end stations and the RingIn ports of DEC token ring products.
It may be set off(2) for lobe connection to IBM 8228 or
equivalent 'dumb' linecards which do not drive phantom current.
The factory default is on(1).
The value of this object is maintained across power cycles
and resets.rw Enumeration .1.3.6.1.4.1.36.2.18.11.3.3.1.5 |
ptrmLobeAutoPartitionStatusIndicates whether the lobe port has been auto-partitioned.
When autoPartitioned(2), a lobe is automatically wrapped.ro Enumeration .1.3.6.1.4.1.36.2.18.11.3.3.1.6 |
ptrmLobeDetectedSpeedIndicates the speed detected on the incoming data pair.
If invalid(1) a valid token ring speed was not detected.
If notApplicable(4), the lobe port does not implement
speed detect.ro Enumeration .1.3.6.1.4.1.36.2.18.11.3.3.1.7 |
ptrmLobePhantomDriveThis variable is not applicable to lobe ports, and is
defined only as a place holder for the corresponding trunk
variable.ro Enumeration .1.3.6.1.4.1.36.2.18.11.3.3.1.8 |
ptrmLobePhantomDetectIndicates the state of the incoming phantom current detect
circuit for the lobe port. Lobe ports are required to implement
phantom detect circuitry; the notApplicable code is provided
only for the corresponding trunk port variable.ro Enumeration .1.3.6.1.4.1.36.2.18.11.3.3.1.9 |
ptrmMacTableA table with entries. The table has 1 entry per MAC chip it contains. SEQUENCE OF PtrmMacEntry .1.3.6.1.4.1.36.2.18.11.3.4 |
ptrmMacEntryAn entry for the Mac . PtrmMacEntry .1.3.6.1.4.1.36.2.18.11.3.4.1 |
ptrmMacIndexAn index into the table. There is 1 entry in the table per MAC chipro INTEGER .1.3.6.1.4.1.36.2.18.11.3.4.1.1 |
ptrmMacRingInterfaceIndicates the Ring Interface number corresponding to this MAC.
Typically single-ring devices will have only 1 Ring Interface.
Devices like the Active Retimed concentartor which suppport
multiple segements may have more than 1 ring interface.
Note - the interface number must match that reported in the
dot5.mibro INTEGER .1.3.6.1.4.1.36.2.18.11.3.4.1.2 |
ptrmMacAddressThe Mac address in MSB form for this interface.ro OCTET STRING .1.3.6.1.4.1.36.2.18.11.3.4.1.3 |
ptrmMacPositionThis is the position of the Mac Chip.
For modules like the DTMXM, the position of the MAC is settable
via software. It can be either before port 1 (MacForward) or
after its last port (MacBackward)
This makes it easy to partition the ports on its own ring
for an accurate ring map.
Modules that are end-stations and hence have no lobe ports may
report Mac position as 1.
if the Mac is in MacForward position the ptrmMacPosition should be
reported as 255.
For all other Ports, if the Mac is between port A and port B,
the Mac postion should be reported as port A.ro INTEGER .1.3.6.1.4.1.36.2.18.11.3.4.1.4 |
ptrmMultiBp OBJECT IDENTIFIER .1.3.6.1.4.1.36.2.18.11.3.5 |
ptrmNumBackplanePortsNumber of physical TokenRing backplane ports.ro INTEGER .1.3.6.1.4.1.36.2.18.11.3.5.1 |
ptrmNumLobePortsNumber of lobe ports the linecard hasro INTEGER .1.3.6.1.4.1.36.2.18.11.3.5.2 |
ptrmMultiBpPortTableThis table MUST be supported by TR linecards like the MIPPY, which
support multiple physical Token Ring backplane ports.
The number of rows in ptrmMultiBpPortTable will be
ptrmNumBackplanePorts
The ptrmBase group does not have to supported in this
configuration. SEQUENCE OF PtrmMultiBpPortEntry .1.3.6.1.4.1.36.2.18.11.3.5.3 |
ptrmMultiBpPortEntry PtrmMultiBpPortEntry .1.3.6.1.4.1.36.2.18.11.3.5.3.1 |
ptrmMultiBpPortIndexIndex into the table. Corresponds to backplane port number.ro INTEGER .1.3.6.1.4.1.36.2.18.11.3.5.3.1.1 |
ptrmMultiBpPortSpeedIndicates the speed at which the backplane port is operating.
The port MUST have a default speed of 4Mbps or 16Mbps
to support plug and play operationro Enumeration .1.3.6.1.4.1.36.2.18.11.3.5.3.1.2 |
ptrmMultiBpPortForceSpeedThis is used only for STANDALONE operation.
This object selects the speed at which to token ring port
operates.
The value of this object is maintained across power cycles
and resets.rw Enumeration .1.3.6.1.4.1.36.2.18.11.3.5.3.1.3 |