DEC-ELAN-MIB
AI MIB Summary
Standard SNMP MIB module defining data structures for DEC-ELAN-MIB.
755
Objects
Active
Status
3
Dependencies
Imported Objects
Objects
755 total| Object Name |
|---|
dec OBJECT IDENTIFIER .1.3.6.1.4.1.36 |
RFC1155-SMI Unknown .1.3.6.1.4.1.36 |
ema OBJECT IDENTIFIER .1.3.6.1.4.1.36.2 |
sysobjid OBJECT IDENTIFIER .1.3.6.1.4.1.36.2.15 |
bridges OBJECT IDENTIFIER .1.3.6.1.4.1.36.2.15.3 |
gigaswitch OBJECT IDENTIFIER .1.3.6.1.4.1.36.2.15.3.3 |
minimumGIGAswitchMIBVersionSupportedWhen new GIGAswitch MIBs are released to the public,
they will be given new version numbers. The
implementation strategy allows multiple versions to be
supported simultaneously. MIB versions greater than or
equal to this version are still supported.ro INTEGER .1.3.6.1.4.1.36.2.15.3.3.1 |
maximumGIGAswitchMIBVersionSupportedWhen new GIGAswitch MIBs are released to the public,
they will be given new version numbers. The
implementation strategy allows multiple versions to be
supported simultaneously. MIB versions less than or
equal to this version are still supported. A
management station may load a MIB which is not
supported until the GIGAswitch software is updated.ro INTEGER .1.3.6.1.4.1.36.2.15.3.3.2 |
gigaversion1 OBJECT IDENTIFIER .1.3.6.1.4.1.36.2.15.3.3.3 |
gigaBox OBJECT IDENTIFIER .1.3.6.1.4.1.36.2.15.3.3.3.1 |
clockCard OBJECT IDENTIFIER .1.3.6.1.4.1.36.2.15.3.3.3.1.1 |
mgmtMemoryAvailThe number of unused bytes of management
memory available on the clock card. The
management memory is used for storing
management parameters.ro INTEGER .1.3.6.1.4.1.36.2.15.3.3.3.1.1.1 |
mgmtMemoryActionThis object, when read, returns a value of other(1)
unless it is in the middle of rewriting the management
memory. At such times, it will return rewriting(3).
The state will revert to other(1) when the action is
completed.
Setting this variable to rewrite(2) will cause the SCP
to attempt to rewrite the management Memory on the
clock-card. Attempts to set this variable to all other
values result in an error.
Rewriting the management memory gets rid of
duplicate entries, and thus may increase the
available space. This action should be allowed
to complete before intentionally removing power
from the SCP or clock card.
If the value is set to clearAndLock(4), management
memory is completely erased. From this point on,
SNMP operations that write management memory will
fail, except for sets to the mgmtMemoryData
object. In fact, the clearAndLock action must
be set before management memory can be re-written
using the mgmtMemoryData object. The GIGAswitch
must be rebooted after the clearAndLock action
(and after it has been re-written, if so desired)
in order to allow future SNMP operations to be
logged to management memory.rw Enumeration .1.3.6.1.4.1.36.2.15.3.3.3.1.1.2 |
mgmtMemoryTableThe table for managing management memory. SEQUENCE OF MgmtMemoryEntry .1.3.6.1.4.1.36.2.15.3.3.3.1.1.3 |
mgmtMemoryEntryA record of management memory. MgmtMemoryEntry .1.3.6.1.4.1.36.2.15.3.3.3.1.1.3.1 |
mgmtMemoryIndexIndex of 80 byte binary recordsro INTEGER .1.3.6.1.4.1.36.2.15.3.3.3.1.1.3.1.1 |
mgmtMemoryDataSNMP object mgmtMemoryData allows the user to read
management memory and, with certain restrictions,
to write it as well. In particular, this object
allows the user to read a management memory image
and, at a later time, restore it. Management
memory is accessed in uninterpreted 80-byte binary
records, numbered starting from 1. As a
result, doing a GET of instance number N will
return bytes 80*(N-1) through 80*N-1 from
management memory. If an attempt is made to read
beyond the end of written flash, an error is
returned; if a read of a record spans the end of
written flash, only the valid data is returned.
To restore a management memory image, management
memory must first be cleared and locked using the
clearAndLock action on the mgmtMemoryAction
object. Then management memory may be written
sequentially, writing 80 bytes at a time until the
last write, at which point less than 80 bytes may
be written. During this operation, and until the
GIGAswitch is rebooted, other SNMP sets requiring
writes to management memory may not be done. It
is therefore recommended that the GIGAswitch be
booted as soon as possible after management memory
has been restored.
Any attempt to write a management memory record
out of sequence, for example writing record 5
followed by record 4 or record 7, results in an
error.rw OCTET STRING .1.3.6.1.4.1.36.2.15.3.3.3.1.1.3.1.2 |
psc OBJECT IDENTIFIER .1.3.6.1.4.1.36.2.15.3.3.3.1.2 |
pscStatusThe status of the Power System Controller (PSC).ro Enumeration .1.3.6.1.4.1.36.2.15.3.3.3.1.2.1 |
pscFwRevThe firmware revision of the Power System Controller
(PSC).ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.36.2.15.3.3.3.1.2.2 |
pscHwRevThe hardware revision of the Power System Controller
(PSC).ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.36.2.15.3.3.3.1.2.3 |
keyswitchPositionIndicates the position of the keyswitch. The
keyswitch position determines the type of
access allowed to network management and to
out-of-band management.
For SNMP access, secure means no SNMP access.
Local means read-only SNMP access. Other values
allow read-write SNMP access. All access is
still subject to the community string, IP address,
and privileged port restrictions.ro Enumeration .1.3.6.1.4.1.36.2.15.3.3.3.1.2.4 |
pscFwImageStatusThe status of the PSC firmware image. If
the value of this object is
downloadRequired(2), the manager should
download a new firmware image to the PSC.
This can be done by using objects in the
gigaUpgradeSoftware group.ro Enumeration .1.3.6.1.4.1.36.2.15.3.3.3.1.2.5 |
pscBackplaneStatusStatus of the GIGAswitch backplane.ro Enumeration .1.3.6.1.4.1.36.2.15.3.3.3.1.2.6 |
cabinetTemperatureThe cabinet temperature.ro Enumeration .1.3.6.1.4.1.36.2.15.3.3.3.1.2.7 |
temperatureWarningThe value of this variable determines how
the SCP responds to a condition of too high
or too low cabinet temperature, or both both
fans inoperative. If the value is heedWarning(1)
the system will be shut down when the temperature
goes outside the designed limits or both fans are
inoperative. If the value is ignoreWarning(2),
the system will continue to operate when either
of these conditions occur.
Setting this variable to ignoreWarning(2) allows
the manager to cause a system that is too hot or
too cold to continue to run. This variable will
also allow both fans to be inoperative and still
allow the system to continue to run. Managers
should note that doing so may be detrimental to
the equipment.
This object has a default value of heedWarning(1).rw Enumeration .1.3.6.1.4.1.36.2.15.3.3.3.1.2.8 |
powerSupply OBJECT IDENTIFIER .1.3.6.1.4.1.36.2.15.3.3.3.1.3 |
rightPowerStatusThe status of the right power unit.ro Enumeration .1.3.6.1.4.1.36.2.15.3.3.3.1.3.1 |
rightPowerInputSourceThe input source of the right power unit.
A value of ACline(1) is returned if the power supply
is connected to an AC line.
A value of DC48V(2) is returned if the power supply is
connected to a 48 volt DC (telecommunications) line.
A value of none(3) is returned if the power unit is not
present or not powered on.
See the batteryUsing object to see if the battery or
this power source is being used.ro Enumeration .1.3.6.1.4.1.36.2.15.3.3.3.1.3.2 |
rightPowerOutputPowerOutput power of right power unit, in watts.ro INTEGER .1.3.6.1.4.1.36.2.15.3.3.3.1.3.3 |
leftPowerStatusThe status of the left power unit.ro Enumeration .1.3.6.1.4.1.36.2.15.3.3.3.1.3.4 |
leftPowerInputSourceThe input source of the left power unit.
A value of ACline(1) is returned if the power supply
is connected to an AC line.
A value of DC48V(2) is returned if the power supply is
connected to a 48 volt DC (telecommunications) line.
A value of none(3) is returned if the power unit is not
present or not powered on.
See the batteryUsing object to see if the battery or
this power source is being used.ro Enumeration .1.3.6.1.4.1.36.2.15.3.3.3.1.3.5 |
leftPowerOutputPowerOutput power of left power unit, in watts.ro INTEGER .1.3.6.1.4.1.36.2.15.3.3.3.1.3.6 |
slot OBJECT IDENTIFIER .1.3.6.1.4.1.36.2.15.3.3.3.1.4 |
slotNumberThe number of slots in the box.ro INTEGER .1.3.6.1.4.1.36.2.15.3.3.3.1.4.1 |
scpSlotIdentifies the slot the Switch Control
Processor (SCP) occupies. A value of 0 will
be returned if an SCP has not been chosen.ro INTEGER .1.3.6.1.4.1.36.2.15.3.3.3.1.4.2 |
slotTableDescribes the current configuration of the box. SEQUENCE OF SlotEntry .1.3.6.1.4.1.36.2.15.3.3.3.1.4.3 |
slotEntryThe description and status of the card
plugged into the slot. SlotEntry .1.3.6.1.4.1.36.2.15.3.3.3.1.4.3.1 |
slotIndexThe slot number. Varies from 1 to slotNumber.ro INTEGER .1.3.6.1.4.1.36.2.15.3.3.3.1.4.3.1.1 |
slotCardStatusThe status of the card. If the value is
read as notPresent(1), then the entire entry
should be considered invalid.
Writing a value of powerDown(2) will cause
the SCP to power down the card. Writing a
value of powerUp(3) will cause the SCP to
power up the card. Writing a value of
powerDownThenUp(4) will cause the SCP to power
cycle the line card. Attempts to set any other
values will result in a badValue error.
The clock and crossbar cards cannot be powered
up or down through this object. They are fundamental
to the GIGAswitch's operation. Unpopulated slots
are notPresent(1), and can not be powered up or
down.rw Enumeration .1.3.6.1.4.1.36.2.15.3.3.3.1.4.3.1.2 |
slotCardTypeThe type of the Card.ro Enumeration .1.3.6.1.4.1.36.2.15.3.3.3.1.4.3.1.3 |
slotCardHwRevThe Hardware revision number of the card.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.36.2.15.3.3.3.1.4.3.1.4 |
slotCardFwRevThe Firmware revision number of the card.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.36.2.15.3.3.3.1.4.3.1.5 |
hostSlotTableDescribes the current IP address and community
string of any modules which are hosted in the
switch (eg GS2000). SEQUENCE OF HostSlotEntry .1.3.6.1.4.1.36.2.15.3.3.3.1.4.4 |
hostSlotEntryThe IP and community of the module hosted
in the slot corresponding to the index. HostSlotEntry .1.3.6.1.4.1.36.2.15.3.3.3.1.4.4.1 |
hostSlotIndexThe slot number. Varies from 1 to slotNumber.ro INTEGER .1.3.6.1.4.1.36.2.15.3.3.3.1.4.4.1.1 |
hostIPThe IP address of the hosted module.rw IpAddress .1.3.6.1.4.1.36.2.15.3.3.3.1.4.4.1.2 |
fan OBJECT IDENTIFIER .1.3.6.1.4.1.36.2.15.3.3.3.1.5 |
fanSpeedThe speed of the fans.
Set this variable to maximum(1) for maximum
cooling where noise does not matter.
Set this variable to normal(2) to cause
fan speeds to be under temperature control.rw Enumeration .1.3.6.1.4.1.36.2.15.3.3.3.1.5.1 |
rightFanStatusThe status of the right fan tray.ro Enumeration .1.3.6.1.4.1.36.2.15.3.3.3.1.5.2 |
leftFanStatusThe status of the left fan tray.ro Enumeration .1.3.6.1.4.1.36.2.15.3.3.3.1.5.3 |
battery OBJECT IDENTIFIER .1.3.6.1.4.1.36.2.15.3.3.3.1.6 |
batteryStatusThe status of the backup battery.ro Enumeration .1.3.6.1.4.1.36.2.15.3.3.3.1.6.1 |
batteryUsingThe source of power being used for the box. The
value batteryPower(2) indicates that the backup
battery unit is being used to power the GIGAswitch.
The external power line can be either AC or a
48 volt DC telecommunications power line.ro Enumeration .1.3.6.1.4.1.36.2.15.3.3.3.1.6.2 |
batteryChargeThe charge-level of the backup battery.
Meaningful only if the battery is present.ro Enumeration .1.3.6.1.4.1.36.2.15.3.3.3.1.6.3 |
batteryTestOnly the value test(3) can be written. Writes of
other values are erroneous.
This shows the result of the last battery test
performed. Testing the battery is risky, since the
GIGAswitch is temporarily switched to run off the
battery, and if the battery-backup system is not
working properly, the GIGAswitch fails and restarts.
Meaningful only if the battery is present.ro Enumeration .1.3.6.1.4.1.36.2.15.3.3.3.1.6.4 |
fppn OBJECT IDENTIFIER .1.3.6.1.4.1.36.2.15.3.3.3.1.7 |
fppnTableA list of front panel port number to MIB-II interface
number mappings. SEQUENCE OF FppnEntry .1.3.6.1.4.1.36.2.15.3.3.3.1.7.1 |
fppnEntryAssigns the MIB-II interface ifIndex for a physical
datalink (cable) connection to the box. FppnEntry .1.3.6.1.4.1.36.2.15.3.3.3.1.7.1.1 |
fppnSlotNumberThe 1-based slot number of the module.ro INTEGER .1.3.6.1.4.1.36.2.15.3.3.3.1.7.1.1.1 |
fppnPortOfThatSlotThe 1-based media connection to the module.ro INTEGER .1.3.6.1.4.1.36.2.15.3.3.3.1.7.1.1.2 |
fppnIfIndexThe assigned MIB-II ifIndex.ro INTEGER .1.3.6.1.4.1.36.2.15.3.3.3.1.7.1.1.3 |
fppnBridgePortNumberThe assigned Bridge MIB dot1dBasePort.ro INTEGER .1.3.6.1.4.1.36.2.15.3.3.3.1.7.1.1.4 |
lineCard OBJECT IDENTIFIER .1.3.6.1.4.1.36.2.15.3.3.3.1.8 |
mPortTableA list of mPort entries. SEQUENCE OF MPortEntry .1.3.6.1.4.1.36.2.15.3.3.3.1.8.1 |
mPortEntryA collection of objects containing information
for a given mPort MAC entity MPortEntry .1.3.6.1.4.1.36.2.15.3.3.3.1.8.1.1 |
mPortSMTIndexThe value of the SMT index associated with this mPort MAC.ro INTEGER .1.3.6.1.4.1.36.2.15.3.3.3.1.8.1.1.1 |
mPortMACIndexThe value of the MAC index associated with this mPort MAC.ro INTEGER .1.3.6.1.4.1.36.2.15.3.3.3.1.8.1.1.2 |
mPortEnableWhen true, this link will be enabled to operate
in concentrator mode, i.e. mport.rw Enumeration .1.3.6.1.4.1.36.2.15.3.3.3.1.8.1.1.3 |
led OBJECT IDENTIFIER .1.3.6.1.4.1.36.2.15.3.3.3.1.9 |
ledTableA list of LED entries, one for each module. SEQUENCE OF LedTableEntry .1.3.6.1.4.1.36.2.15.3.3.3.1.9.1 |
ledTableEntryEach entry describes the state of one module. LedTableEntry .1.3.6.1.4.1.36.2.15.3.3.3.1.9.1.1 |
ledTableIndexThe module index into the table.ro INTEGER .1.3.6.1.4.1.36.2.15.3.3.3.1.9.1.1.1 |
ledCountThe number of LEDs on this module.ro INTEGER .1.3.6.1.4.1.36.2.15.3.3.3.1.9.1.1.2 |
ledSlotTableA list of LED entries, one for each module LED. SEQUENCE OF LedEntry .1.3.6.1.4.1.36.2.15.3.3.3.1.9.2 |
ledEntryEach entry describes the state of one module LED. LedEntry .1.3.6.1.4.1.36.2.15.3.3.3.1.9.2.1 |
ledSlotIndexThe slot index into the table.ro INTEGER .1.3.6.1.4.1.36.2.15.3.3.3.1.9.2.1.1 |
ledLedIndexThe led index within the slot given by slotIndex.ro INTEGER .1.3.6.1.4.1.36.2.15.3.3.3.1.9.2.1.2 |
ledDescrA textual description of the information which the LED is
meant to convey. i.e.:
+5 Volt Power, DC Okay
ATM port activity.
Diagnostic status.ro DisplayString .1.3.6.1.4.1.36.2.15.3.3.3.1.9.2.1.3 |
ledProgramThe ledProgram string is a sequence of instructions
for the LED state. The LED constantly repeats the
program. Each LED state is represented by a two octet
sequence where the value of the first octet of the pair
indicates the color of the LED, and the value of the
second octet of the pair indicates the duration in which
that color will be present.
++ ++
| Color | Duration | | Color | Duration |
++ ++
The 'color' octet may have one of the following values:
0 - off
1 - other
2 - red
3 - yellow
4 - green
5 - blue
6 - red-blinking
7 - yellow-blinking
8 - blue-blinking
9 - green-blinking
The value 'off' indicates that the LED is off.
The value 'other' indicates a color not covered by any
others in the list.
The value of the second octet in each pair indicates the
duration in which that color will be present. A value
of zero indicates that the LED is off. A value of 0xff
indicates that the LED is always on. Values in between
0 and 0xff indicate the duration in 10 ms ticks.
A zero length string may be returned if the LED is 'not
present'. This indicates that the LED is currently not
visible.
Activity LEDs are a special case. Activity LEDs are
defined as LEDs which blink whenever data is received on
the line. They are typically on solid under heavy
activity. Since these LEDs can change rapidly, the
following rules apply:
o The initial state of activity LEDs is off.
o If the line shows activity any time in a 10 second
period, then the LED is shown as on.
o If the line shown inactivity any time in a 10 second
period, then the LED is shown as off.
See the 'pcomLedProgram' object in the DECHUB900-COMMON MIB
for examples.ro OCTET STRING .1.3.6.1.4.1.36.2.15.3.3.3.1.9.2.1.4 |
gigaBridge OBJECT IDENTIFIER .1.3.6.1.4.1.36.2.15.3.3.3.2 |
filterByReferencedExpression OBJECT IDENTIFIER .1.3.6.1.4.1.36.2.15.3.3.3.2.1 |
ebrNportMatrixNameTableThis table allows filter matrices to be succinctly
specified and named. These matrices may later be used
and combined in filter specifications. SEQUENCE OF EbrNportMatrixNameEntry .1.3.6.1.4.1.36.2.15.3.3.3.2.1.1 |
ebrNportMatrixNameEntryA particular named filter matrix. EbrNportMatrixNameEntry .1.3.6.1.4.1.36.2.15.3.3.3.2.1.1.1 |
ebrNportMatrixNameThis name for a filter matrix is whatever the user likes,
as long as it is a unique filter matrix name.ro DisplayString .1.3.6.1.4.1.36.2.15.3.3.3.2.1.1.1.1 |
ebrNportMatrixValueA matrix is expressed using a shorthand that says what
input ports can talk to what output ports.
An examples of a specification is:
11:1; 1:3-5; 2:0,3; 4-7,9:4-7,9; 10:
Semicolons separate expressions. Within each expression,
the colon has a left hand side and a right hand side. Bridge
ports on the left hand side can send packets to bridge ports
on the right hand side. Commas separate items in a list of
bridge ports. Hyphens are short-hand for specifying a range
of numbers. If there is no right hand side, the bridge ports
on the left cannot send packets to any bridge port (unless the
matrix is combined with some some other matrix in a filter
specification, or unless the filter is overridden).
Bridge port numbers are specified in decimal.
A matrix will read back in a form equivalent to the form
written. It may not read back exactly as written.
No single matrix defines whether a packet arriving on a port
is forwarded to its destination. Various destination address,
source address, protocol, and default filtering specifications
are combined to determine whether the packet is forwarded.
If the ebrNportMatrixValue is changed, all filters using it are
immediately updated.rw DisplayString .1.3.6.1.4.1.36.2.15.3.3.3.2.1.1.1.2 |
ebrNportMatrixStatusAssigning the value invalid will result in an error
while the matrix is still reference by some filter.
All matrices are permanent; it is their usage which may or may
not be temporary.rw Enumeration .1.3.6.1.4.1.36.2.15.3.3.3.2.1.1.1.3 |
ebrNportMatrixFppnValueA matrix is expressed using a shorthand that says what
input ports can talk to what output ports.
An examples of a specification is:
1.1,2.1-14.2:1.1-14.2; 2.2:5.3,6.4; 10.3:;
Semicolons separate expressions. Within each expression,
the colon has a left hand side and a right hand side. Front
panel ports on the left hand side can send packets to front
panel ports on the right hand side. Commas separate items in
a list of front panel ports. Hyphens are short-hand for
specifying a range of numbers. If there is no right hand side,
the front panel ports on the left cannot send packets to any
front panel port (unless the matrix is combined with some some
other matrix in a filter specification, or unless the filter is
overridden).
Front panel port numbers are of the form (slot.connector),
where slot is the slot number the module is plugged into,
and connector is the connector number specified on the
front of the card.
A matrix will read back in a form equivalent to the form
written. It may not read back exactly as written.
No single matrix defines whether a packet arriving on a port
is forwarded to its destination. Various destination address,
source address, protocol, and default filtering specifications
are combined to determine whether the packet is forwarded.
If the ebrNportMatrixFppnValue is changed, all filters using
it are immediately updated.
Managers may not specify both ebrNportMatrixValue and
ebrNportMatrixFppnValue at the same time to set an entry
in this table.rw DisplayString .1.3.6.1.4.1.36.2.15.3.3.3.2.1.1.1.4 |
ebrNportSapNameTableThe filters specified by SAP protocol. SEQUENCE OF EbrNportSapNameEntry .1.3.6.1.4.1.36.2.15.3.3.3.2.1.2 |
ebrNportSapNameEntryA portion of a particular filter for a particular SAP
protocol. EbrNportSapNameEntry .1.3.6.1.4.1.36.2.15.3.3.3.2.1.2.1 |
ebrNportSapNameThis name for a portion of a filter is whatever the user
likes, as long as it is a unique ebrNportSapName.
The combination of ebrNportSapNameSap and ebrNportSapMatrixName
is unique within this table. Insertions of new names for
pre-existing combinations will be denied.
ebrNportSapName is present and is the index to give a mnemonic
handle on the combination of SAP and matrix for purposes of
discussion and of access through the network management station
user interface. SAPs, for example, are often just meaningless
numbers unless laborious steps are taken to interpret them.ro DisplayString .1.3.6.1.4.1.36.2.15.3.3.3.2.1.2.1.1 |
ebrNportSapNameSapThe one-byte SAP.
Changes to ebrNportSapProtoTable for this SAP are denied while
filtering of the SAP is specified by reference to a named
matrix using this table.rw OCTET STRING .1.3.6.1.4.1.36.2.15.3.3.3.2.1.2.1.2 |
ebrNportSapMatrixNameA ebrNportMatrixName. Multiple matrices for the same SAP
are combined using an elementwise-OR operator.rw DisplayString .1.3.6.1.4.1.36.2.15.3.3.3.2.1.2.1.3 |
ebrNportSapNameDispfilter(1) : The filtering for this SAP is specified by the
filter matrix.
alwaysFilter(2) : Frames of this SAP (protocol) are
filtered regardless of any other alwaysForward
dispositions based on the frame's address.
The filtering information is specified by the
filter matrix.
alwaysForward(3) : Frames for this SAP (protocol) are
sent to ports specified in the filter matrix
regardless of any address filter with a
disposition of filter. The alwaysForward disposition
also overrides a forwarding disposition of filter
in the default filter matrix object.
Filters with a disposition of alwaysFilter are never
superceded.
Setting this object will cause a side effect on the
ebrNportSapFilterCharacteristicsTable entry for this SAP. It
is here to group information for window-based forms. Setting
this object will also cause a side effect on other entries in
this table with the same SAP value.rw Enumeration .1.3.6.1.4.1.36.2.15.3.3.3.2.1.2.1.4 |
ebrNportSapNameStatusThis object specifies the permanence of the associated filter
matrix, and also provides a means to delete a filter matrix.
Writing invalid(1) to the object removes the filter.
Writing permanent(2) value to the object indicates the filter
is preserved across a bridge reset.rw Enumeration .1.3.6.1.4.1.36.2.15.3.3.3.2.1.2.1.5 |
ebrNportSnapNameTableThe filters specified by Protocol ID for the SNAP SAP. SEQUENCE OF EbrNportSnapNameEntry .1.3.6.1.4.1.36.2.15.3.3.3.2.1.3 |
ebrNportSnapNameEntryA portion of a particular filter for a particular
Protocol ID. EbrNportSnapNameEntry .1.3.6.1.4.1.36.2.15.3.3.3.2.1.3.1 |
ebrNportSnapNameThis name for a portion of a filter is whatever the user
likes, as long as it is a unique ebrNportSnapName.
The combination of ebrNportSnapNameSnap and
ebrNportSnapMatrixName is unique within this table. Insertions
of new names for pre-existing combinations will be denied.
ebrNportSnapName is present and is the index to give a mnemonic
handle on the combination of protocol and matrix for purposes
of discussion and of access through the network management
station user interface. Protocol IDs, for example, are often
just meaningless numbers unless laborious steps are taken to
interpret them.ro DisplayString .1.3.6.1.4.1.36.2.15.3.3.3.2.1.3.1.1 |
ebrNportSnapNameSnapThe five-byte PID.
Changes to ebrNportSnapProtoTable for this protocol are denied
while filtering of the protocol is specified by reference to a
named matrix using this table.rw OCTET STRING .1.3.6.1.4.1.36.2.15.3.3.3.2.1.3.1.2 |
ebrNportSnapMatrixNameA ebrNportMatrixName. Multiple matrices for the same PID
are combined using an elementwise-OR operator.rw DisplayString .1.3.6.1.4.1.36.2.15.3.3.3.2.1.3.1.3 |
ebrNportSnapNameDispfilter(1) : The filtering for this Protocol ID
is specified by the filter matrix.
alwaysFilter(2) : Frames of this Protocol ID are
filtered regardless of any other alwaysForward
dispositions based on the frame's address.
The filtering information is specified by the
filter matrix.
alwaysForward(3) : Frames for this Protocol ID are
sent to ports specified in the filter matrix
regardless of any address filter with a
disposition of filter. The alwaysForward disposition
also overrides a forwarding disposition of filter
in the default filter matrix object.
Filters with a disposition of alwaysFilter are never
superceded.
Setting this object will cause a side effect on the
ebrNportSnapFilterCharacteristicsTable entry for this protocol.
It is here to group information for window-based forms.
Setting this object will also cause a side effect onother
entries in this table with the same protocol value.rw Enumeration .1.3.6.1.4.1.36.2.15.3.3.3.2.1.3.1.4 |
ebrNportSnapNameStatusThis object specifies the permanence of the associated filter
matrix, and also provides a means to delete a filter matrix.
Writing invalid(1) to the object removes the filter.
Writing permanent(2) value to the object indicates the filter
is preserved across a bridge reset.rw Enumeration .1.3.6.1.4.1.36.2.15.3.3.3.2.1.3.1.5 |
ebrNportDANameTableThe filters specified by destination address. SEQUENCE OF EbrNportDANameEntry .1.3.6.1.4.1.36.2.15.3.3.3.2.1.4 |
ebrNportDANameEntryA portion of a particular filter for a particular
destination address. EbrNportDANameEntry .1.3.6.1.4.1.36.2.15.3.3.3.2.1.4.1 |
ebrNportDANameThis name for a portion of a filter is whatever the user likes,
as long as it is a unique ebrNportDAName.
The combination of ebrNportDANameDA and ebrNportDAMatrixName
is unique within this table. Insertions of new names for
pre-existing combinations will be denied.
ebrNportDAName is present and is the index to give a mnemonic
handle on the combination of address and matrix for purposes of
discussion and of access through the network management station
user interface. Addresses, for example, are often just
meaningless numbers unless laborious steps are taken to
interpret them.ro DisplayString .1.3.6.1.4.1.36.2.15.3.3.3.2.1.4.1.1 |
ebrNportDANameDAThe six-byte destination address.
Changes to ebrNportStaticDATable for this address are denied
while filtering of the address is specified by reference to a
named matrix using this table.rw OCTET STRING .1.3.6.1.4.1.36.2.15.3.3.3.2.1.4.1.2 |
ebrNportDAMatrixNameA ebrNportMatrixName. Multiple matrices for the same
address are combined using an elementwise-OR operator.rw DisplayString .1.3.6.1.4.1.36.2.15.3.3.3.2.1.4.1.3 |
ebrNportDANameDispfilter(1) : The filtering for this address is specified by
the filter matrix.
alwaysFilter(2) : Frames destined to address are filtered
regardless of any other alwaysForward dispositions
based on the frame's source address or protocol type.
The filtering information is specified by the filter
matrix.
alwaysForward(3) : Frames destined to address are always
forwarded to ebrNportPortNum if specified.
The filter matrix is used to specify ports to
which frames may be sent. In both cases, this
disposition overrides filters based on the frame's
source address or protocol type, unless either of those
filters has an alwaysFilter disposition.
Setting this object will side effect the
ebrNportStaticDAFilterCharacteristicsTable entry for this
address. It is here to group information for window-based
forms. Setting this object will also cause a side effect
on other entries in this table with the same address.rw Enumeration .1.3.6.1.4.1.36.2.15.3.3.3.2.1.4.1.4 |
ebrNportDANameStatusother(1) - This entry is currently in use, but the
conditions under which it will remain so are different
from each of the following values. Like other uses
of 'other' in MIBs, this value may not be assigned to
the object.
invalid(2) - Writing this value to the object removes the entry
permanent(3) - Writing this value to the object indicates that
the entry is preserved across a bridge reset.
deleteOnReset(4) - Writing this value removes the permanent
entry characteristic. The entry is deleted upon the
next bridge reset (SCP or GIGAswitch failure).
Writing deleteOnReset is not supported. SNMP does not
currently model viewing the non-volatile and volatile
data structures independently, which can lead to
unexpectedly having no filter if a reset occurs while
temporarily trying a change to an existing filter.
Writes of this value will result in a bad value return
status. It is present for consistency with the Bridge
MIB (RFC 1286), which describes address filters.
deleteOnTimeout(5) - Writing this value removes the permanent
entry characteristic. Since the timers used for aging
information within the bridge are hidden from the user,
the change may in fact take place immediately.
Writing deleteOnTimeout is not supported. SNMP does
not currently model viewing the non-volatile and
volatile data structures independently, which can lead
to unexpectedly having no filter if a reset occurs
while temporarily trying a change to an existing
filter. Writes of this value will result in a bad
value return status. It is present for consistency
with the Bridge MIB (RFC 1286), which describes address
filters.rw Enumeration .1.3.6.1.4.1.36.2.15.3.3.3.2.1.4.1.5 |
ebrNportSANameTableThe filters specified by source address. SEQUENCE OF EbrNportSANameEntry .1.3.6.1.4.1.36.2.15.3.3.3.2.1.5 |
ebrNportSANameEntryA portion of a particular filter for a particular source
address. EbrNportSANameEntry .1.3.6.1.4.1.36.2.15.3.3.3.2.1.5.1 |
ebrNportSANameThis name for a portion of a filter is whatever the user
likes, as long as it is a unique ebrNportSAName.
The combination of ebrNportSANameSA and ebrNportSAMatrixName
is unique within this table. Insertions of new names for
pre-existing combinations will be denied.
ebrNportSAName is present and is the index to give a mnemonic
handle on the combination of address and matrix for purposes of
discussion and of access through the network management station
user interface. Addresses, for example, are often just
meaningless numbers unless laborious steps are taken to
interpret them.ro DisplayString .1.3.6.1.4.1.36.2.15.3.3.3.2.1.5.1.1 |
ebrNportSANameSAThe six-byte source address.
Changes to ebrNportStaticSATable for this address are denied
while filtering of the address is specified by reference to a
named matrix using this table.rw OCTET STRING .1.3.6.1.4.1.36.2.15.3.3.3.2.1.5.1.2 |
ebrNportSAMatrixNameA ebrNportMatrixName. Multiple matrices for the same
address are combined using an elementwise-OR operator.rw DisplayString .1.3.6.1.4.1.36.2.15.3.3.3.2.1.5.1.3 |
ebrNportSANameDispThis object specifies how to interpret the ebrNportPortNum and
the ebrNportSAMatrixName objects.
portMask(1) : The static filtering for this address
is specified by the filter matrix.
alwaysFilter(2) : Frames sourced from this address are
filtered regardless of any other alwaysForward
dispositions based on the frame's destination address
or protocol type. The static filtering information is
specified by the filter matrix.
alwaysForward(3) : Frames sourced from this address are
sent to ports specified in the filter matrix
regardless of any DA or protocol filter with a
disposition of filter. The alwaysForward disposition
also overrides a forwarding disposition of filter
in the default filter matrix object.
Filters with a disposition of alwaysFilter are never
superceded.
lockdown (4) : Frames sourced from this address
are ONLY forwarded if received on the same port as
ebrNportPortNum.
lockdownportmask (5) : Frames sourced from this address
are ONLY forwarded if received on the same port as
ebrNportPortNum AND if the frame is destined to a
permitted port as specified by the filter matrix.
filter(6) : The static filtering for this address
is specified by the filter matrix. portMask(1) is
the different name with the same effect.
Setting this object will side effect the
ebrNportStaticSAFilterCharacteristicsTable entry for this
address. It is here to group information for window-based
forms. Setting this object will also cause a side effect
on other entries in this table with the same address.rw Enumeration .1.3.6.1.4.1.36.2.15.3.3.3.2.1.5.1.4 |
ebrNportSANameStatusother(1) - This entry is currently in use, but the
conditions under which it will remain so are different
from each of the following values. Like other uses
of 'other' in MIBs, this value may not be assigned to
the object.
invalid(2) - Writing this value to the object removes the entry
permanent(3) - Writing this value to the object indicates that
the entry is preserved across a bridge reset.
deleteOnReset(4) - Writing this value removes the permanent
entry characteristic. The entry is deleted upon the
next bridge reset (SCP or GIGAswitch failure).
Writing deleteOnReset is not supported. SNMP does not
currently model viewing the non-volatile and volatile
data structures independently, which can lead to
unexpectedly having no filter if a reset occurs while
temporarily trying a change to an existing filter.
Writes of this value will result in a bad value return
status. It is present for consistency with the Bridge
MIB (RFC 1286), which describes address filters.
deleteOnTimeout(5) - Writing this value removes the permanent
entry characteristic. Since the timers used for aging
information within the bridge are hidden from the user,
the change may in fact take place immediately.
Writing deleteOnTimeout is not supported. SNMP does
not currently model viewing the non-volatile and
volatile data structures independently, which can lead
to unexpectedly having no filter if a reset occurs
while temporarily trying a change to an existing
filter. Writes of this value will result in a bad
value return status. It is present for consistency
with the Bridge MIB (RFC 1286), which describes address
filters.rw Enumeration .1.3.6.1.4.1.36.2.15.3.3.3.2.1.5.1.5 |
ebrNportDefaultMatrixValueA matrix is expressed using a shorthand that says what
input ports can talk to what output ports.
An examples of a specification is:
11:1; 1:3-5; 2:0,3; 4-7,9:4-7,9; 10:
Semicolons separate expressions. Within each expression,
the colon has a left hand side and a right hand side. Bridge
ports on the left hand side can send packets to bridge ports
on the right hand side. Commas separate items in a list of
bridge ports. Hyphens are short-hand for specifying a range
of numbers. If there is no right hand side, the bridge ports
on the left cannot send packets to any bridge port (unless the
matrix is combined with some some other matrix in a filter
specification, or unless the filter is overridden).
Bridge port numbers are specified in decimal.
A matrix will read back in a form equivalent to the form
written. It may not read back exactly as written.
No single matrix defines whether a packet arriving on a port
is forwarded to its destination. Various destination address,
source address, protocol, and default filtering specifications
are combined to determine whether the packet is forwarded.
Unspecified rows are set to one's, which means that the
corresponding input ports can communicate with every
output port.rw DisplayString .1.3.6.1.4.1.36.2.15.3.3.3.2.1.6 |
ebrNportManualFilterThe list of bridge ports in manual mode is listed.
Manual mode means that the bridge purges the learned entries
for that port from its forwarding database, stops its learning
process on that port, and forwards to that port only frames
with destination and source addresses that have been specified
via management.
A comma-separated list of bridge ports, with hyphens used to
abbreviate ranges, is supported. The bridge port numbers are
in decimal.rw DisplayString .1.3.6.1.4.1.36.2.15.3.3.3.2.1.7 |
ebrNportMatrixNameRowTableThis table is another view of ebrNportMatrixNameTable. Changes
to this table cause changes to ebrNportMatrixNameTable.
Users or programs can choose whichever matrix specification
language they feel more comfortable with. This table also
side-steps issues of the worst-case ascii representation length
on the part of either ebrNportMatrixNameTable or the management
station interface. SEQUENCE OF EbrNportMatrixNameRowEntry .1.3.6.1.4.1.36.2.15.3.3.3.2.1.8 |
ebrNportMatrixNameRowEntryA particular row of a particular named filter matrix. EbrNportMatrixNameRowEntry .1.3.6.1.4.1.36.2.15.3.3.3.2.1.8.1 |
ebrNportmatrixNameThis name for a filter matrix is whatever the user likes,
as long as it is a unique filter matrix name.
Same as ebrNportMatrixName.ro DisplayString .1.3.6.1.4.1.36.2.15.3.3.3.2.1.8.1.1 |
ebrNportMatrixReceivePortA bridge port number. Zero is treated as in other tables,
and is short-hand for all rows not previously mentioned.ro INTEGER .1.3.6.1.4.1.36.2.15.3.3.3.2.1.8.1.2 |
ebrNportMatrixAllowedToGoToJust like all the other GoTos. The set of ports to which
frames received from a specific port are allowed to be
forwarded.
Each octet of this object specifies a set of eight ports,
with the first octet specifying ports 1 through 8,
the second octet specifying port 9 through 16 etc.
Within each octet, the most significant bit represents
the lowest numbered port, and the least significant
bit represents the highest numbered port. If a
bit has a value of '1', then the corresponding port
is included in the set of ports; the port is not
included if its bit has a value of '0'.
If the ebrNportMatrixAllowedToGoTo is changed, all filters
using it are immediately updated.rw OCTET STRING .1.3.6.1.4.1.36.2.15.3.3.3.2.1.8.1.3 |
ebrNportMatrixNameRowStatusAssigning the value invalid will delete the row of the matrix.
Attempting to delete the last ebrNportmatrixName entry for a
matrix will result in an error while the matrix is still
reference by some filter.
All matrices are permanent; it is their usage which may or may
not be temporary.rw Enumeration .1.3.6.1.4.1.36.2.15.3.3.3.2.1.8.1.4 |
ebrNportDefaultMatrixFppnValueA matrix is expressed using a shorthand that says what
input front panel ports can talk to what output front
panel ports.
An examples of a specification is:
1.1,2.1-14.2:1.1-14.2; 2.2:5.3,6.4; 10.3:;
Semicolons separate expressions. Within each expression,
the colon has a left hand side and a right hand side. Front
panel ports on the left hand side can send packets to front
panel ports on the right hand side. Commas separate items in
a list of front panel ports. Hyphens are short-hand for
specifying a range of numbers. If there is no right hand side,
the front panel ports on the left cannot send packets to any
front panel port (unless the matrix is combined with some some
other matrix in a filter specification, or unless the filter is
overridden).
Front panel port numbers are of the form (slot.connector),
where slot is the slot number the module is plugged into,
and connector is the connector number specified on the
front of the card.
A matrix will read back in a form equivalent to the form
written. It may not read back exactly as written.
No single matrix defines whether a packet arriving on a port
is forwarded to its destination. Various destination address,
source address, protocol, and default filtering specifications
are combined to determine whether the packet is forwarded.
Unspecified rows are set to one's, which means that the
corresponding input ports can communicate with every
output port.rw DisplayString .1.3.6.1.4.1.36.2.15.3.3.3.2.1.9 |
ebrNportFppnManualFilterThe list of front panel ports in manual mode is listed.
Manual mode means that the bridge purges the learned entries
for that port from its forwarding database, stops its learning
process on that port, and forwards to that port only frames
with destination and source addresses that have been specified
via management.
A comma-separated list of front panel ports, with hyphens used
to abbreviate ranges, is supported.
Front panel port numbers are of the form (slot.connector),
where slot is the slot number the module is plugged into,
and connector is the connector number specified on the
front of the card.rw DisplayString .1.3.6.1.4.1.36.2.15.3.3.3.2.1.10 |
ebrNportMatrixFppnRowTableThis table is yet another view of ebrNportMatrixNameTable.
Changes to this table cause changes to ebrNportMatrixNameTable.
Users or programs can choose whichever matrix specification
language they feel more comfortable with. This table also
side-steps issues of the worst-case ascii representation length
on the part of either ebrNportMatrixNameTable or the management
station interface. SEQUENCE OF EbrNportMatrixFppnRowEntry .1.3.6.1.4.1.36.2.15.3.3.3.2.1.11 |
ebrNportMatrixFppnRowEntryA particular row of a particular named filter matrix. EbrNportMatrixFppnRowEntry .1.3.6.1.4.1.36.2.15.3.3.3.2.1.11.1 |
ebrNportmatrixnameThis name for a filter matrix is whatever the user likes,
as long as it is a unique filter matrix name.
Same as ebrNportMatrixName.ro DisplayString .1.3.6.1.4.1.36.2.15.3.3.3.2.1.11.1.1 |
ebrNportMatrixFppnReceivePortFront panel port numbers are of the form (slot.connector),
where slot is the slot number the module is plugged into,
and connector is the connector number specified on the
front of the card.
To avoid the syntactic ambiguity, the slot number must take
two characters. For example, front panel port number 3.1
must be typed by 03.1. 0.0 is treated as in other tables,
and is short-hand for all rows not previously mentioned.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.36.2.15.3.3.3.2.1.11.1.2 |
ebrNportMatrixFppnAllowedToGoToJust like all the other GoTos. The set of ports to which
frames received from a specific port are allowed to be
forwarded.
Each octet of this object specifies a set of eight ports,
with the first octet specifying ports 1 through 8,
the second octet specifying port 9 through 16 etc.
Within each octet, the most significant bit represents
the lowest numbered port, and the least significant
bit represents the highest numbered port. If a
bit has a value of '1', then the corresponding port
is included in the set of ports; the port is not
included if its bit has a value of '0'.
If the ebrNportMatrixFppnAllowedToGoTo is changed, all filters
using it are immediately updated.rw OCTET STRING .1.3.6.1.4.1.36.2.15.3.3.3.2.1.11.1.3 |
ebrNportMatrixFppnRowStatusAssigning the value invalid will delete the row of the matrix.
Attempting to delete the last ebrNportmatrixname entry for a
matrix will result in an error while the matrix is still
reference by some filter.
All matrices are permanent; it is their usage which may or may
not be temporary.rw Enumeration .1.3.6.1.4.1.36.2.15.3.3.3.2.1.11.1.4 |
ebrNportNamedDefaultMatrixWhen a matrix name is written to this object, the default
matrix is set to the matrix if and only if the matrix
exists.
Unspecified rows in the matrix are set to one's, which means
that the corresponding input ports can communicate with every
output port.rw DisplayString .1.3.6.1.4.1.36.2.15.3.3.3.2.1.12 |
ebrNportDefaultMatrixRowTableThis table is another view of ebrNportDefaultMatrixValue. SEQUENCE OF EbrNportDefaultMatrixRowEntry .1.3.6.1.4.1.36.2.15.3.3.3.2.1.13 |
ebrNportDefaultMatrixRowEntryA particular row of the default matrix. EbrNportDefaultMatrixRowEntry .1.3.6.1.4.1.36.2.15.3.3.3.2.1.13.1 |
ebrNportDefaultMatrixReceivePortA bridge port number.ro INTEGER .1.3.6.1.4.1.36.2.15.3.3.3.2.1.13.1.1 |
ebrNportDefaultMatrixAllowedToGoToThe set of ports to which frames received from a specific
port are allowed to be forwarded by default.
Each octet of this object specifies a set of eight ports,
with the first octet specifying ports 1 through 8,
the second octet specifying port 9 through 16 etc.
Within each octet, the most significant bit represents
the lowest numbered port, and the least significant
bit represents the highest numbered port. If a
bit has a value of '1', then the corresponding port
is included in the set of ports; the port is not
included if its bit has a value of '0'.ro OCTET STRING .1.3.6.1.4.1.36.2.15.3.3.3.2.1.13.1.2 |
ebrNportFloodMatrixValueA flood matrix is expressed using a shorthand that says
what input ports can be flooded to what output ports.
Unspecified rows are set to one's, which means that the
corresponding input ports can be flooded to every
output port.rw DisplayString .1.3.6.1.4.1.36.2.15.3.3.3.2.1.14 |
ebrNportFloodMatrixFppnValueA flood matrix is expressed using a shorthand that says
what input front panel ports can be flooded to what output
front panel ports.
Unspecified rows are set to one's, which means that the
corresponding input ports can be flooded to every
output port.rw DisplayString .1.3.6.1.4.1.36.2.15.3.3.3.2.1.15 |
ebrNportNamedFloodMatrixWhen a matrix name is written to this object, the flood
matrix is set to the matrix if and only if the matrix
exists.
Unspecified rows in the matrix are set to one's, which means
that the corresponding input ports can be flooded to every
output port.rw DisplayString .1.3.6.1.4.1.36.2.15.3.3.3.2.1.16 |
ebrNportFloodMatrixRowTableThis table is another view of ebrNportFloodMatrixValue. SEQUENCE OF EbrNportFloodMatrixRowEntry .1.3.6.1.4.1.36.2.15.3.3.3.2.1.17 |
ebrNportFloodMatrixRowEntryA particular row of the flood matrix. EbrNportFloodMatrixRowEntry .1.3.6.1.4.1.36.2.15.3.3.3.2.1.17.1 |
ebrNportFloodMatrixReceivePortA bridge port number.ro INTEGER .1.3.6.1.4.1.36.2.15.3.3.3.2.1.17.1.1 |
ebrNportFloodMatrixAllowedToGoToThe set of ports to which frames received from a specific
port are allowed to be flooded by default.ro OCTET STRING .1.3.6.1.4.1.36.2.15.3.3.3.2.1.17.1.2 |
filterByBitmapValue OBJECT IDENTIFIER .1.3.6.1.4.1.36.2.15.3.3.3.2.2 |
ebrNportSapProtoTableA table that contains filtering information about
802.2 SAPs in the DSAP field for N-port bridges. SEQUENCE OF EbrNportSapProtoEntry .1.3.6.1.4.1.36.2.15.3.3.3.2.2.1 |
ebrNportSapProtoEntryA table that contains filtering information about
802.2 SAPs in the DSAP field for N-port bridges. EbrNportSapProtoEntry .1.3.6.1.4.1.36.2.15.3.3.3.2.2.1.1 |
ebrNportSapValueThe 802.2 DSAP in a frame to which this entry's
filtering information applies.rw OCTET STRING .1.3.6.1.4.1.36.2.15.3.3.3.2.2.1.1.1 |
ebrNportSapReceivePortThe port from which a frame must be received to use
the corresponding ebrNportSapAllowedToGoTo. A value of
zero indicates that this entry applies on all ports of
the bridge for which there is no other applicable entry.rw INTEGER .1.3.6.1.4.1.36.2.15.3.3.3.2.2.1.1.2 |
ebrNportSapAllowedToGoToThe set of ports to which frames received from
a specific port and containing the DSAP in an 802
frame specified by ebrNportSapValue are
allowed to be forwarded.
Each octet of this object specifies a set of eight ports,
with the first octet specifying ports 1 through 8,
the second octet specifying port 9 through 16 etc.
Within each octet, the most significant bit represents
the lowest numbered port, and the least significant
bit represents the highest numbered port. If a
bit has a value of '1', then the corresponding port
is included in the set of ports; the port is not
included if its bit has a value of '0'.
Filter matrix rows can be initialized or overwritten, but not
deleted. Only whole matrices are deleted via the
characteristics table. To produce the equivalent of row
deletion, set the GoTo according to the following table:
Disp GoTo
filter/portMask 0xFFFFFFFFF0
alwaysFilter 0xFFFFFFFFF0
alwaysForward 0rw OCTET STRING .1.3.6.1.4.1.36.2.15.3.3.3.2.2.1.1.3 |
ebrNportSapFilterCharacteristicsTableA table that contains information about how 802.2 DSAP
filters are used within N-port bridges. SEQUENCE OF EbrNportSapFilterCharacteristicsEntry .1.3.6.1.4.1.36.2.15.3.3.3.2.2.2 |
ebrNportSapFilterCharacteristicsEntry802.2 DSAP filter usage for N-port bridges. EbrNportSapFilterCharacteristicsEntry .1.3.6.1.4.1.36.2.15.3.3.3.2.2.2.1 |
ebrNportSapFilterCharacteristicsSapValueThe 802.2 DSAP in a frame to which this entry's
information applies. The value of this object is
the same as ebrNportSapValue.rw OCTET STRING .1.3.6.1.4.1.36.2.15.3.3.3.2.2.2.1.1 |
ebrNportSapDispThis object specifies how to interpret the
ebrNportSapAllowedToGoTo values for the specified SAP.
filter(1) : The filtering for this SAP is specified by the
filter matrix.
alwaysFilter(2) : Frames of this SAP (protocol) are
filtered regardless of any other alwaysForward
dispositions based on the frame's address.
The filtering information is specified by the
filter matrix.
alwaysForward(3) : Frames for this SAP (protocol) are
sent to ports specified in the filter matrix
regardless of any address filter with a
disposition of filter. The alwaysForward disposition
also overrides a forwarding disposition of filter
in the default filter matrix object.
Filters with a disposition of alwaysFilter are never
superceded.rw Enumeration .1.3.6.1.4.1.36.2.15.3.3.3.2.2.2.1.2 |
ebrNportSapStatusThis object specifies the permanence of the associated filter
matrix, and also provides a means to delete a filter matrix.
Writing invalid(1) to the object removes the filter.
Writing permanent(2) value to the object indicates the filter is
preserved across a bridge reset.rw Enumeration .1.3.6.1.4.1.36.2.15.3.3.3.2.2.2.1.3 |
ebrNportSnapProtoTableA table that contains filtering information about
5-byte SNAP Protocol IDs (PIDs) for N-port bridges. SEQUENCE OF EbrNportSnapProtoEntry .1.3.6.1.4.1.36.2.15.3.3.3.2.2.3 |
ebrNportSnapProtoEntryA table that contains filtering information about
5-byte SNAP Protocol IDs (PIDs) for N-port bridges. EbrNportSnapProtoEntry .1.3.6.1.4.1.36.2.15.3.3.3.2.2.3.1 |
ebrNportSnapValueThe SNAP Protocol ID (PID) in an 802 frame to which this
entry's filtering information applies.rw OCTET STRING .1.3.6.1.4.1.36.2.15.3.3.3.2.2.3.1.1 |
ebrNportSnapReceivePortThe port from which a frame must be received to use
the corresponding ebrNportSnapAllowedToGoTo. A value of
zero indicates that this entry applies on all ports of
the bridge for which there is no other applicable entry.rw INTEGER .1.3.6.1.4.1.36.2.15.3.3.3.2.2.3.1.2 |
ebrNportSnapAllowedToGoToThe set of ports to which frames received from
a specific port and containing the SNAP PID in an
802 frame specified by ebrNportSnapValue are
allowed to be forwarded.
Each octet of this object specifies a set of eight ports,
with the first octet specifying ports 1 through 8,
the second octet specifying port 9 through 16 etc.
Within each octet, the most significant bit represents
the lowest numbered port, and the least significant
bit represents the highest numbered port. If a
bit has a value of '1', then the corresponding port
is included in the set of ports; the port is not
included if its bit has a value of '0'.
Filter matrix rows can be initialized or overwritten, but not
deleted. Only whole matrices are deleted via the
characteristics table. To produce the equivalent of row
deletion, set the GoTo according to the following table:
Disp GoTo
filter/portMask 0xFFFFFFFFF0
alwaysFilter 0xFFFFFFFFF0
alwaysForward 0rw OCTET STRING .1.3.6.1.4.1.36.2.15.3.3.3.2.2.3.1.3 |
ebrNportSnapFilterCharacteristicsTableA table that contains information about how SNAP Protocol ID
(PID) filters are used within N-port bridges. SEQUENCE OF EbrNportSnapFilterCharacteristicsEntry .1.3.6.1.4.1.36.2.15.3.3.3.2.2.4 |
ebrNportSnapFilterCharacteristicsEntry802.2 SNAP Protocol ID (PID) filter usage for N-port bridges. EbrNportSnapFilterCharacteristicsEntry .1.3.6.1.4.1.36.2.15.3.3.3.2.2.4.1 |
ebrNportSnapFilterCharacteristicsSnapValueThe SNAP Protocol ID (PID) in a frame to which this entry's
information applies. The value of this object is the same as
ebrNportSnapValue.rw OCTET STRING .1.3.6.1.4.1.36.2.15.3.3.3.2.2.4.1.1 |
ebrNportSnapDispThis object specifies how to interpret the
ebrNportSnapAllowedToGoTo values for the specified SNAP PID.
filter(1) : The filtering for this Protocol ID
is specified by the filter matrix.
alwaysFilter(2) : Frames of this Protocol ID are
filtered regardless of any other alwaysForward
dispositions based on the frame's address.
The filtering information is specified by the
filter matrix.
alwaysForward(3) : Frames for this Protocol ID are
sent to ports specified in the filter matrix
regardless of any address filter with a
disposition of filter. The alwaysForward disposition
also overrides a forwarding disposition of filter
in the default filter matrix object.
Filters with a disposition of alwaysFilter are never
superceded.rw Enumeration .1.3.6.1.4.1.36.2.15.3.3.3.2.2.4.1.2 |
ebrNportSnapStatusThis object specifies the permanence of the associated filter
matrix, and also provides a means to delete a filter matrix.
Writing invalid(1) to the object removes the filter.
Writing permanent(2) value to the object indicates the filter is
preserved across a bridge reset.rw Enumeration .1.3.6.1.4.1.36.2.15.3.3.3.2.2.4.1.3 |
ebrNportStaticDATableThis table contains management-specified destination address
filtering information about unicast and multicast addresses
for N-port bridges. In RFC 1286 lingo, static objects are
those objects which have been specified by network management. SEQUENCE OF EbrNportStaticDAEntry .1.3.6.1.4.1.36.2.15.3.3.3.2.2.5 |
ebrNportStaticDAEntryInformation about a specific MAC address for which the bridge
has some management-specified forwarding and/or filtering
information. EbrNportStaticDAEntry .1.3.6.1.4.1.36.2.15.3.3.3.2.2.5.1 |
ebrNportDAAddressThe destination MAC Address in a frame to
which this entry's filtering information applies.rw OCTET STRING .1.3.6.1.4.1.36.2.15.3.3.3.2.2.5.1.1 |
ebrNportDAReceivePortThe port from which a frame must be received to use
the corresponding ebrNportDAAllowedToGoTo field.
A value of zero indicates that this entry applies on all ports
of the bridge for which there is no other applicable entry.rw INTEGER .1.3.6.1.4.1.36.2.15.3.3.3.2.2.5.1.2 |
ebrNportDAAllowedToGoToThe set of ports to which frames received from
a specific port and destined to the address specified by
ebrNportDAAddress are allowed to be forwarded.
Each octet of this object specifies a set of eight ports,
with the first octet specifying ports 1 through 8,
the second octet specifying port 9 through 16 etc.
Within each octet, the most significant bit represents
the lowest numbered port, and the least significant
bit represents the highest numbered port. If a
bit has a value of '1', then the corresponding port
is included in the set of ports; the port is not
included if its bit has a value of '0'.
Filter matrix rows can be initialized or overwritten, but not
deleted. Only whole matrices are deleted via the
characteristics table. To produce the equivalent of row
deletion, set the GoTo according to the following table:
Disp GoTo
filter/portMask 0xFFFFFFFFF0
alwaysFilter 0xFFFFFFFFF0
alwaysForward 0rw OCTET STRING .1.3.6.1.4.1.36.2.15.3.3.3.2.2.5.1.3 |
ebrNportStaticDAFilterCharacteristicsTableA table that contains information about how static destination
address filters (for unicast and multicast addresses) are used
within N-port bridges. Static objects are those objects which
have been specified by network management. SEQUENCE OF EbrNportStaticDAFilterCharacteristicsEntry .1.3.6.1.4.1.36.2.15.3.3.3.2.2.6 |
ebrNportStaticDAFilterCharacteristicsEntryInformation about a specific static MAC destination address
filter's usage within N-port bridges. EbrNportStaticDAFilterCharacteristicsEntry .1.3.6.1.4.1.36.2.15.3.3.3.2.2.6.1 |
ebrNportDestinationAddressThe destination MAC Address in a frame to which this entry's
information applies. The value of this object is the same
as ebrNportDAAddress.rw OCTET STRING .1.3.6.1.4.1.36.2.15.3.3.3.2.2.6.1.1 |
ebrNportDADispThis object specifies how to interpret the ebrNportPortNum and
ebrNportDAAllowedToGoTo objects.
filter(1) : The filtering for this address is specified by
the filter matrix.
alwaysFilter(2) : Frames destined to address are filtered
regardless of any other alwaysForward dispositions
based on the frame's source address or protocol type.
The filtering information is specified by the filter
matrix.
alwaysForward(3) : Frames destined to address are always
forwarded to ebrNportPortNum if specified.
The filter matrix is used to specify ports to
which frames may be sent. In both cases, this
disposition overrides filters based on the frame's
source address or protocol type, unless either of those
filters has an alwaysFilter disposition.rw Enumeration .1.3.6.1.4.1.36.2.15.3.3.3.2.2.6.1.2 |
ebrNportDAStatusother(1) - This entry is currently in use, but the
conditions under which it will remain so are different
from each of the following values. Like other uses
of 'other' in MIBs, this value may not be assigned to
the object.
invalid(2) - Writing this value to the object removes the entry
permanent(3) - Writing this value to the object indicates that
the entry is preserved across a bridge reset.
deleteOnReset(4) - Writing this value removes the permanent
entry characteristic. The entry is deleted upon the
next bridge reset (SCP or GIGAswitch failure).
Writing deleteOnReset is not supported. SNMP does not
currently model viewing the non-volatile and volatile
data structures independently, which can lead to
unexpectedly having no filter if a reset occurs while
temporarily trying a change to an existing filter.
Writes of this value will result in a bad value return
status. It is present for consistency with the Bridge
MIB (RFC 1286), which describes address filters.
deleteOnTimeout(5) - Writing this value removes the permanent
entry characteristic. Since the timers used for aging
information within the bridge are hidden from the user,
the change may in fact take place immediately.
Writing deleteOnTimeout is not supported. SNMP does
not currently model viewing the non-volatile and
volatile data structures independently, which can lead
to unexpectedly having no filter if a reset occurs
while temporarily trying a change to an existing
filter. Writes of this value will result in a bad
value return status. It is present for consistency
with the Bridge MIB (RFC 1286), which describes
address filters.rw Enumeration .1.3.6.1.4.1.36.2.15.3.3.3.2.2.6.1.3 |
ebrNportStaticSATableA table that contains static source address filtering
information about unicast and multicast addresses for
N-port bridges. Static objects are those objects which
have been specified by network management. SEQUENCE OF EbrNportStaticSAEntry .1.3.6.1.4.1.36.2.15.3.3.3.2.2.7 |
ebrNportStaticSAEntryInformation about a specific MAC address for which the
bridge has some static forwarding and/or filtering
information. EbrNportStaticSAEntry .1.3.6.1.4.1.36.2.15.3.3.3.2.2.7.1 |
ebrNportSAAddressThe source MAC Address in a frame to which this entry's
filtering information applies.rw OCTET STRING .1.3.6.1.4.1.36.2.15.3.3.3.2.2.7.1.1 |
ebrNportSAReceivePortThe port from which a frame must be received to use
the corresponding ebrNportSAAllowedToGoTo field.
A value of zero indicates that this entry applies on all
ports of the bridge for which there is no other applicable
entry.rw INTEGER .1.3.6.1.4.1.36.2.15.3.3.3.2.2.7.1.2 |
ebrNportSAAllowedToGoToThe set of ports to which frames received from
a specific port and sourced from the address specified by
ebrNportSAAddress are allowed to be forwarded.
Each octet of this object specifies a set of eight ports,
with the first octet specifying ports 1 through 8,
the second octet specifying port 9 through 16 etc.
Within each octet, the most significant bit represents
the lowest numbered port, and the least significant
bit represents the highest numbered port. If a
bit has a value of '1', then the corresponding port
is included in the set of ports; the port is not
included if its bit has a value of '0'.
Filter matrix rows can be initialized or overwritten, but not
deleted. Only whole matrices are deleted via the
characteristics table. To produce the equivalent of row
deletion, set the GoTo according to the following table:
Disp GoTo
filter/portMask 0xFFFFFFFFF0
alwaysFilter 0xFFFFFFFFF0
alwaysForward 0rw OCTET STRING .1.3.6.1.4.1.36.2.15.3.3.3.2.2.7.1.3 |
ebrNportStaticSAFilterCharacteristicsTableA table that contains information about how static source
address filters (for unicast and multicast addresses) are
used within N-port bridges. SEQUENCE OF EbrNportStaticSAFilterCharacteristicsEntry .1.3.6.1.4.1.36.2.15.3.3.3.2.2.8 |
ebrNportStaticSAFilterCharacteristicsEntryStatic source address filter usage for N-port bridges. EbrNportStaticSAFilterCharacteristicsEntry .1.3.6.1.4.1.36.2.15.3.3.3.2.2.8.1 |
ebrNportSourceAddressThe source MAC Address in a frame to which this entry's
information applies. The value of this object is the
same as ebrNportSAAddress.rw OCTET STRING .1.3.6.1.4.1.36.2.15.3.3.3.2.2.8.1.1 |
ebrNportSADispThis object specifies how to interpret the ebrNportPortNum and
and the ebrNportSAAllowedToGoTo objects.
portMask(1) : The static filtering for this address
is specified by the filter matrix.
alwaysFilter(2) : Frames sourced from this address are
filtered regardless of any other alwaysForward
dispositions based on the frame's destination address
or protocol type. The static filtering information is
specified by the filter matrix.
alwaysForward(3) : Frames sourced from this address are
sent to ports specified in the filter matrix
regardless of any DA or protocol filter with a
disposition of filter. The alwaysForward disposition
also overrides a forwarding disposition of filter
in the default filter matrix object.
Filters with a disposition of alwaysFilter are never
superceded.
lockdown (4) : Frames sourced from this address
are ONLY forwarded if received on the same port as
ebrNportPortNum.
lockdownportmask (5) : Frames sourced from this address
are ONLY forwarded if received on the same port as
ebrNportPortNum AND if the frame is destined to a
permitted port as specified by the filter matrix.
filter(6) : The static filtering for this address
is specified by the filter matrix. portMask(1) is
the different name with the same effect.rw Enumeration .1.3.6.1.4.1.36.2.15.3.3.3.2.2.8.1.2 |
ebrNportSAStatusother(1) - This entry is currently in use, but the
conditions under which it will remain so are different
from each of the following values. Like other uses
of 'other' in MIBs, this value may not be assigned to
the object.
invalid(2) - Writing this value to the object removes the entry
permanent(3) - Writing this value to the object indicates that
the entry is preserved across a bridge reset.
deleteOnReset(4) - Writing this value removes the permanent
entry characteristic. The entry is deleted upon the
next bridge reset (SCP or GIGAswitch failure).
Writing deleteOnReset is not supported. SNMP does not
currently model viewing the non-volatile and volatile
data structures independently, which can lead to
unexpectedly having no filter if a reset occurs while
temporarily trying a change to an existing filter.
Writes of this value will result in a bad value return
status. It is present for consistency with the Bridge
MIB (RFC 1286), which describes address filters.
deleteOnTimeout(5) - Writing this value removes the permanent
entry characteristic. Since the timers used for aging
information within the bridge are hidden from the user,
the change may in fact take place immediately.
Writing deleteOnTimeout is not supported. SNMP does
not currently model viewing the non-volatile and
volatile data structures independently, which can lead
to unexpectedly having no filter if a reset occurs
while temporarily trying a change to an existing
filter. Writes of this value will result in a bad
value return status. It is present for consistency
with the Bridge MIB (RFC 1286), which describes
address filters.rw Enumeration .1.3.6.1.4.1.36.2.15.3.3.3.2.2.8.1.3 |
ebrNportSwTableThis table describes the default filter matrix. SEQUENCE OF EbrNportSwEntry .1.3.6.1.4.1.36.2.15.3.3.3.2.2.9 |
ebrNportSwEntryThe entry describes a row of the default filter matrix. EbrNportSwEntry .1.3.6.1.4.1.36.2.15.3.3.3.2.2.9.1 |
ebrNportSwReceivePortThe bridge port on which a frame must be received to use
the corresponding ebrNportSwAllowedToGoTo field.
A value of zero indicates that this entry applies on all ports
of the bridge for which there is no other management-specified
entry.rw INTEGER .1.3.6.1.4.1.36.2.15.3.3.3.2.2.9.1.1 |
ebrNportSwAllowedToGoToThis object specifies the default forwarding disposition
after all DA, SA, and protocol filters have been applied.
For those cases where no filter applies to the frame, the
forwarding disposition for the frames received on the
ebrNportSwReceivePort interface and sent to one or all of the
bridge's interfaces is determined by the
ebrNportSwAllowedToGoTo object.
Each octet of this object specifies a set of eight ports,
with the first octet specifying ports 1 through 8,
the second octet specifying port 9 through 16 etc.
Within each octet, the most significant bit represents
the lowest numbered port, and the least significant
bit represents the highest numbered port. If a
bit has a value of '1', then the corresponding port
is included in the set of ports; the port is not
included if its bit has a value of '0'.rw OCTET STRING .1.3.6.1.4.1.36.2.15.3.3.3.2.2.9.1.2 |
ebrNportSwManualFilterA switch that controls address filtering. Specifying a
one in a bit position says that the port is in manual
mode.
Each octet of this object specifies a set of eight ports,
with the first octet specifying ports 1 through 8,
the second octet specifying port 9 through 16 etc.
Within each octet, the most significant bit represents
the lowest numbered port, and the least significant
bit represents the highest numbered port. If a
bit has a value of '1', then the corresponding port
is included in the set of ports; the port is not
included if its bit has a value of '0'.
Manual mode means that the bridge purges the learned entries
for that port from its forwarding database, stops its learning
process on that port, and forwards to that port only frames
with destination and source addresses that have been specified
via management.rw OCTET STRING .1.3.6.1.4.1.36.2.15.3.3.3.2.2.10 |
ebrNportPortNumTableA table that contains static (i.e., configured by
network management) information about the bridge
port on which unicast or multicast addresses reside
on N-port bridges. SEQUENCE OF EbrNportPortNumEntry .1.3.6.1.4.1.36.2.15.3.3.3.2.3 |
ebrNportPortNumEntryInformation about a specific MAC address. EbrNportPortNumEntry .1.3.6.1.4.1.36.2.15.3.3.3.2.3.1 |
ebrNportPortNumAddressThe MAC Address to which this entry's information applies.rw OCTET STRING .1.3.6.1.4.1.36.2.15.3.3.3.2.3.1.1 |
ebrNportPortNumThe Port Number to which this address will be
translated (to which frames destined for the address
will be forwarded). There are some filtering nuances
for addresses with specified port numbers which are
determined by the source address and destination address
filter disposition characteristics.
If zero, no port number is specified.
This value is a giganet destination address instead of a
bridge port number if it is greater than 127.rw INTEGER .1.3.6.1.4.1.36.2.15.3.3.3.2.3.1.2 |
ebrNportPortNumStatusThis object specifies the permanence of the specified
information, and also provides a means to delete an entry.
Writing invalid(1) to the object removes the entry.
Writing permanent(2) value to the object indicates the entry is
preserved across a bridge reset.rw Enumeration .1.3.6.1.4.1.36.2.15.3.3.3.2.3.1.3 |
ebrNportFppnPortNumThe Front Panel Port Number to which this address will be
translated (to which frames destined for the address
will be forwarded). There are some filtering nuances
for addresses with specified front panel port numbers
which are determined by the source address and destination
address filter disposition characteristics.
Managers may not specify both ebrNportPortNum and
ebrNportFppnPortNum at the same time to set an entry
in this table.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.36.2.15.3.3.3.2.3.1.4 |
serviceClassAssignments OBJECT IDENTIFIER .1.3.6.1.4.1.36.2.15.3.3.3.2.5 |
ebrNportSapSvcTableA table that contains resource information (e.g., queuing)
about 802.2 SAPs in the DSAP field for N-port bridges. SEQUENCE OF EbrNportSapSvcEntry .1.3.6.1.4.1.36.2.15.3.3.3.2.5.1 |
ebrNportSapSvcEntryResource information about an 802.2 SAP in the DSAP field
for N-port bridges. EbrNportSapSvcEntry .1.3.6.1.4.1.36.2.15.3.3.3.2.5.1.1 |
ebrNportSapSvcSapValueThe 802.2 DSAP in a frame to which this entry's
resource information applies.rw INTEGER .1.3.6.1.4.1.36.2.15.3.3.3.2.5.1.1.1 |
ebrNportSapSvcThe service class used to allocate resources and implement
service policy within the bridge. The service class
associated with a frame is a function of either the frame's
destination address or the frame's protocol. The default
value for this field is 0. This value is used to assign the
single path service class in the absence of an overriding
service class associated with the frame's destination addr.
There are 16 possible service classes, 0-15.
Service classes 1-11 are reserved for internal or future use.rw INTEGER .1.3.6.1.4.1.36.2.15.3.3.3.2.5.1.1.2 |
ebrNportSapSvcStatusThis object specifies the permanence of the specified service
class usage, and also provides a means to delete an entry.
Writing invalid(1) to the object removes the entry.
Writing permanent(2) value to the object indicates the entry is
preserved across a bridge reset.rw Enumeration .1.3.6.1.4.1.36.2.15.3.3.3.2.5.1.1.3 |
ebrNportSapSinglePathThe ebrNportSapSinglePath object is used to set the
single path ports for a ebrNportSapSvcSapValue.
The default is to not use the default (single path)
service class.
ebrNportSapSinglePath is expressed using a shorthand
that specifies which physical ports are to be set to the
default (single path) service class. An example of a specification
would be :
(1,6-9,21)
where commas separate physical ports and hyphens are short-hand
for specifying a range of numbers. This example would assign
physical ports 1,6,7,8,9, and 21 to use the default (single path)
service class, for the given ebrNportSapSvcSapValue.
Physical port numbers are specified in decimal.
A ebrNportSapSinglePath will read back in a form equivalent to
the form written. It may not read back exactly as written.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.36.2.15.3.3.3.2.5.1.1.4 |
ebrNportSnapSvcTableA table that contains resource information (e.g., queuing)
about 5-byte SNAP Protocol IDs (PIDs) for N-port bridges. SEQUENCE OF EbrNportSnapSvcEntry .1.3.6.1.4.1.36.2.15.3.3.3.2.5.2 |
ebrNportSnapSvcEntryResource information about a 5-byte SNAP Protocol ID (PID)
for N-port bridges. EbrNportSnapSvcEntry .1.3.6.1.4.1.36.2.15.3.3.3.2.5.2.1 |
ebrNportSnapSvcSnapValueThe SNAP Protocol ID (PID) in a frame to which this entry's
resource information applies.rw OCTET STRING .1.3.6.1.4.1.36.2.15.3.3.3.2.5.2.1.1 |
ebrNportSnapSvcThe service class used to allocate resources and implement
service policy within the bridge. The service class
associated with a frame is a function of either the frame's
destination address or the frame's protocol. The default
value for this field is 0. This value is used to assign the
single path service class in the absence of an overriding
service class associated with the frame's destination addr.
There are 16 possible service classes, 0-15.
Service classes 1-11 are reserved for internal or future use.rw INTEGER .1.3.6.1.4.1.36.2.15.3.3.3.2.5.2.1.2 |
ebrNportSnapSvcStatusThis object specifies the permanence of the specified service
class usage, and also provides a means to delete an entry.
Writing invalid(1) to the object removes the entry.
Writing permanent(2) value to the object indicates the entry is
preserved across a bridge reset.rw Enumeration .1.3.6.1.4.1.36.2.15.3.3.3.2.5.2.1.3 |
ebrNportSnapSinglePathThe ebrNportSnapSinglePath object is used to set the
single path ports for a ebrNportSnapSvcSnapValue.
The default is to not use the default (single path)
service class.
ebrNportSnapSinglePath is expressed using a shorthand
that specifies which physical ports are to be set to the
default (single path) service class. An example of a specification
would be :
(1,6-9,21)
where commas separate physical ports and hyphens are short-hand
for specifying a range of numbers. This example would assign
physical ports 1,6,7,8,9, and 21 to use the default (single path)
service class, for the given ebrNportSnapSvcSnapValue.
Physical port numbers are specified in decimal.
A ebrNportSnapSinglePath will read back in a form equivalent to
the form written. It may not read back exactly as written.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.36.2.15.3.3.3.2.5.2.1.4 |
ebrNportDASvcTableA table that contains resource information about unicast and
multicast destination addresses for N-port bridges. SEQUENCE OF EbrNportDASvcEntry .1.3.6.1.4.1.36.2.15.3.3.3.2.5.3 |
ebrNportDASvcEntryResource information about a specific MAC destination address
for N-port bridges. EbrNportDASvcEntry .1.3.6.1.4.1.36.2.15.3.3.3.2.5.3.1 |
ebrNportSvcAddressThe destination MAC Address in a frame to which this entry's
resource information applies.rw OCTET STRING .1.3.6.1.4.1.36.2.15.3.3.3.2.5.3.1.1 |
ebrNportSvcThe service class used to allocate resources and implement
service policy within the bridge. The service class
associated with a frame is a function of either the frame's
destination address or the frame's protocol. The default
value for this field is 0. This value is used to assign the
single path service class in the absence of a service class
associated with the frame's protocol. There are 16 possible
service classes, 0-15. The ebrNportSvc allows 32 values to
be specified. The specification of a value greater than 15
is used to connote that the service class (ebrNportSvc-16),
is to be associated with the frame and that this service
class has precedence over a service class associated with
a frame's protocol.
Service classes 1-11 are reserved for internal or future use.rw INTEGER .1.3.6.1.4.1.36.2.15.3.3.3.2.5.3.1.2 |
ebrNportSvcStatusThis object specifies the permanence of the specified service
class usage, and also provides a means to delete an entry.
Writing invalid(1) to the object removes the entry.
Writing permanent(2) value to the object indicates the entry is
preserved across a bridge reset.rw Enumeration .1.3.6.1.4.1.36.2.15.3.3.3.2.5.3.1.3 |
flooding OBJECT IDENTIFIER .1.3.6.1.4.1.36.2.15.3.3.3.2.6 |
floodUnknownUnicastRateThe maximum bytes-per-second bandwidth of packets
multicast because the destination address was not yet
learned by the bridge. The resolution of this value
is 100 bytes-per-second. The 2 LS digits are rounded
down to zero, i.e. 1-99 => 0.rw INTEGER .1.3.6.1.4.1.36.2.15.3.3.3.2.6.1 |
floodMulticastRateThe maximum bytes-per-second bandwidth of packets
multicast because the destination address is a
multicast address.The resolution of this value
is 100 bytes-per-second. The 2 LS digits are rounded
down to zero, i.e. 1-99 => 0.rw INTEGER .1.3.6.1.4.1.36.2.15.3.3.3.2.6.2 |
floodTableDetailed view of the bridge flooding process. SEQUENCE OF FloodEntry .1.3.6.1.4.1.36.2.15.3.3.3.2.6.3 |
floodEntryFlooding state for a packet class and source. FloodEntry .1.3.6.1.4.1.36.2.15.3.3.3.2.6.3.1 |
floodQuotaQualifierThe quota qualifier describes an incoming or outgoing
port. It is a linear index to the port starting from
1. If n is the quota qualifier for the first port of
a two port line card, the quota qualifier for the
second port is n + 1. The clock card and the crossbar
have zero port, so the index must be skipped over those
slots. This numbering scheme may be changed as we have
four port line cards.ro INTEGER .1.3.6.1.4.1.36.2.15.3.3.3.2.6.3.1.1 |
floodQuotaClassThe quota class describes the type of packet.
Four packet types are classified as follows:
1 - Unknown Destination Packets,
2 - Multicast Packets,
3 - IS-IS Packets,
4 - Bursty Control Packetsro INTEGER .1.3.6.1.4.1.36.2.15.3.3.3.2.6.3.1.2 |
floodBytesSentThis object is the count of bytes in flooded packets.
It does not include filtered packets or packets
discarded due to buffer limitations. Each packet is
counted once, regardless of the number of outbound
links to which it was flooded.ro Counter .1.3.6.1.4.1.36.2.15.3.3.3.2.6.3.1.3 |
floodPacketsSentThis object is the count of flooded packets.
It does not include filtered packets or packets
discarded due to buffer limitations. Each packet is
counted once, regardless of the number of outbound
links to which it was flooded.ro Counter .1.3.6.1.4.1.36.2.15.3.3.3.2.6.3.1.4 |
floodGeezersThis object is the count of packets that could not be
flooded because they had remained in the SCP or in the
inbound linecard too long.ro Counter .1.3.6.1.4.1.36.2.15.3.3.3.2.6.3.1.5 |
floodLosersThis object is the count of packets discarded by the
SCP flooding software (at the interrupt level) due to
insufficient buffering.ro Counter .1.3.6.1.4.1.36.2.15.3.3.3.2.6.3.1.6 |
floodHogsThis object is the count of packets for which buffer
quota conversion to flooding software optimistic quotas
failed. This includes packets that were discarded as
well as packets that were successfully flooded.ro Counter .1.3.6.1.4.1.36.2.15.3.3.3.2.6.3.1.7 |
floodSinglePathDiscardsThis object is the count of packets discarded to
prevent packet misordering. Certain protocol types
are considered single-path and may not be delivered out
of order. If the Destination Address for a packet
having a single-path protocol type is learned while
the packet is buffered by the flooding software,
the packet must be discarded (since line cards would
have been directly forwarding packets using the learned
address while packets received earlier were buffered on
the SCP).ro Counter .1.3.6.1.4.1.36.2.15.3.3.3.2.6.3.1.8 |
floodPacketsFilteredThis object is the count of packets discarded by the
flooding software because user-configured filtering
resulted in no allowed outbound transmit ports.ro Counter .1.3.6.1.4.1.36.2.15.3.3.3.2.6.3.1.9 |
floodPacketsPurgedThis object is the count of packets discarded due to
the incoming link leaving FORWARDING state while they
were buffered by flooding software.ro Counter .1.3.6.1.4.1.36.2.15.3.3.3.2.6.3.1.10 |
floodBytesPurgedThis object is the byte count in packets discarded due
to the incoming link leaving FORWARDING state while
they were buffered by flooding software.ro Counter .1.3.6.1.4.1.36.2.15.3.3.3.2.6.3.1.11 |
floodLocalCopyPacketsDeliveredThis object is the count of multicast packets addressed
to software modules in the SCP that have been
successfully delivered to those modules.ro Counter .1.3.6.1.4.1.36.2.15.3.3.3.2.6.3.1.12 |
floodLocalCopyPacketsDiscardedThis object is the count of multicast packets addressed
to software modules in the SCP that, because of buffer
limitations, could not be delivered to those modules.ro Counter .1.3.6.1.4.1.36.2.15.3.3.3.2.6.3.1.13 |
cutThrough OBJECT IDENTIFIER .1.3.6.1.4.1.36.2.15.3.3.3.2.7 |
cutThroughTableThis table controls the enabling of some hardware performance
enhancements that avoid store-and-forward delays during packet
forwarding, whenever possible. SEQUENCE OF CutThroughEntry .1.3.6.1.4.1.36.2.15.3.3.3.2.7.1 |
cutThroughEntryInformation about the enabling of some hardware performance
enhancements that avoid store-and-forward delays for a specific
bridge port. CutThroughEntry .1.3.6.1.4.1.36.2.15.3.3.3.2.7.1.1 |
cutThroughBridgePortThe dot1dBasePort bridge port number for this table entry.rw INTEGER .1.3.6.1.4.1.36.2.15.3.3.3.2.7.1.1.1 |
cutThroughInboundIf true, some hardware performance enhancements are enabled
to avoid store-and-forward delays when packets enter the
GIGAswitch.
If false, the whole packet is buffered on the line card at
which the packet enters the GIGAswitch before it is sent
to the line card at which the packet leaves the GIGAswitch.
Cut-through is normally enabled.rw Enumeration .1.3.6.1.4.1.36.2.15.3.3.3.2.7.1.1.2 |
cutThroughOutboundIf true, some hardware performance enhancements are enabled
to avoid store-and-forward delays when packets leave the
GIGAswitch.
If false, the whole packet is buffered on the line card at
which the packet leaves the GIGAswitch before it is sent
out of the GIGAswitch.
Cut-through is normally enabled.rw Enumeration .1.3.6.1.4.1.36.2.15.3.3.3.2.7.1.1.3 |
cutThroughFppnTableThis table controls the enabling of some hardware performance
enhancements that avoid store-and-forward delays during packet
forwarding, whenever possible. SEQUENCE OF CutThroughFppnEntry .1.3.6.1.4.1.36.2.15.3.3.3.2.7.2 |
cutThroughFppnEntryInformation about the enabling of some hardware performance
enhancements that avoid store-and-forward delays for a specific
front panel port. CutThroughFppnEntry .1.3.6.1.4.1.36.2.15.3.3.3.2.7.2.1 |
cutThroughFppnPortThe front panel port number for this table entry.
Front panel port numbers are of the form (slot.connector),
where slot is the slot number the module is plugged into,
and connector is the connector number specified on the
front of the card.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.36.2.15.3.3.3.2.7.2.1.1 |
cutThroughFppnInboundIf true, some hardware performance enhancements are enabled
to avoid store-and-forward delays when packets enter the
GIGAswitch.
If false, the whole packet is buffered on the line card at
which the packet enters the GIGAswitch before it is sent
to the line card at which the packet leaves the GIGAswitch.
Cut-through is normally enabled.rw Enumeration .1.3.6.1.4.1.36.2.15.3.3.3.2.7.2.1.2 |
cutThroughFppnOutboundIf true, some hardware performance enhancements are enabled
to avoid store-and-forward delays when packets leave the
GIGAswitch.
If false, the whole packet is buffered on the line card at
which the packet leaves the GIGAswitch before it is sent
out of the GIGAswitch.
Cut-through is normally enabled.rw Enumeration .1.3.6.1.4.1.36.2.15.3.3.3.2.7.2.1.3 |
gigaStp OBJECT IDENTIFIER .1.3.6.1.4.1.36.2.15.3.3.3.2.8 |
gigaStpPortTableA list of gigaStp entries SEQUENCE OF GigaStpPortEntry .1.3.6.1.4.1.36.2.15.3.3.3.2.8.1 |
gigaStpPortEntryA collection of objects containing information
for a given StpPort GigaStpPortEntry .1.3.6.1.4.1.36.2.15.3.3.3.2.8.1.1 |
gigaStpPortIfIndexThe value of the interface associated with this
spanning tree port.ro INTEGER .1.3.6.1.4.1.36.2.15.3.3.3.2.8.1.1.1 |
gigaStpPortSpanningTreeEnableWhen true, this interface will be enabled to operate
as part of the spanning tree. When trueNoDelay, this
interface will be enabled to operate as part of the
spanning tree but will have a pre-forwarding delay
of zero.rw Enumeration .1.3.6.1.4.1.36.2.15.3.3.3.2.8.1.1.2 |
gigaStpDemandLearningEnableIf true, then when a source address is learned, the address is
only written to the Translation Table in the bridge port on which
it was learned. If the address later occurs as a destination
address in a packet received on some other bridge port, the
packet is flooded if possible and the address is written to the
Translation table of the other bridge port at that time. Thus, a
bridge port that receives no packets for a certain address will
not have that address in its database unless the address had been
learned on that bridge port.
If false, then when a source address is learned, the address is
promptly written to the Translation Table of every bridge port in
the GIGASwitch.
This variable should be set to yes if the total number of
learned addresses is expected to be greater than the number
supported by the linecards and if there is sufficient locality of
traffic that the behavior described above will not result in more
than that number of addresses being learned on any one bridge
port.
It should be set to no if the total number of learned addresses
is not greater than the number supported by the linecards and if
it is desired to avoid flooding of packets to already-learned
addresses.rw Enumeration .1.3.6.1.4.1.36.2.15.3.3.3.2.8.2 |
translationTableParams OBJECT IDENTIFIER .1.3.6.1.4.1.36.2.15.3.3.3.2.9 |
ttSizeThe number of entries in the tables used to store
learned network addresses.ro INTEGER .1.3.6.1.4.1.36.2.15.3.3.3.2.9.1 |
xacInDiscardCounters OBJECT IDENTIFIER .1.3.6.1.4.1.36.2.15.3.3.3.2.10 |
xacInDiscardUnknownDAUCastThis object shows the number of unknown DA unicast
packets which are transmitted from linecards to the
SCP for multicasting, but discarded due to the lack
of buffer space in the XAC chip.
Packets counted here are not included in other,
per-port, discard counters because this counter
is shared by all the incoming ports.ro Counter .1.3.6.1.4.1.36.2.15.3.3.3.2.10.1 |
xacInDiscardMulticastThis object shows the number of multicast packets
which are transmitted from linecards to the SCP for
processing, but discarded due to the lack of buffer
space in the XAC chip.
Packets counted here are not included in other,
per-port, discard counters because this counter
is shared by all the incoming ports.ro Counter .1.3.6.1.4.1.36.2.15.3.3.3.2.10.2 |
xacInDiscardIPForwardingThis object shows the number of IP packets which
are transmitted from linecards to the SCP for
forwarding, but discarded due to the lack of buffer
space in the XAC chip.
Packets counted here are not included in other,
per-port, discard counters because this counter
is shared by all the incoming ports.ro Counter .1.3.6.1.4.1.36.2.15.3.3.3.2.10.3 |
communityString OBJECT IDENTIFIER .1.3.6.1.4.1.36.2.15.3.3.3.2.11 |
communityStringDelimiterThe communityStringDelimiter object is used to delimit
community string suffixes. Community string suffixes give
the SNMP agent additional information to process certain
objects. If the objects do not need the suffix then the
suffix is ignored. If the object uses the suffix and none
is supplied, then a default is used. There are two valid
suffixes available for the Gigaswitch/Fddi, LDx and LBDx.
LDx references learning domains, LD1-LD8. LBDx references
logical bridge domains, LBD1- LBD8. Both uppercase and
lowercase are valid. The default communityStringDelimiter
is the ':'.
ex. public:LD3, use learning domain 4 if required
public:LBD4, use logical bridge domain 4 if
required
public, use default if required.
The set of Valid communityStringDelimiter is the set of all
printable characters minus all the alphas and all the
digits.
If a LDx suffix is used where an LBDx is required, then the
LBD that contains the LDx will be used. If a LBDx suffix is
used where an LDx is required, then the lowest numbered LD
in that LBD is used. In both cases if there are no members
in the LD/LBD then the default is used. The default LD is
LD1 and the default LBD is LBD1.rw OCTET STRING .1.3.6.1.4.1.36.2.15.3.3.3.2.11.1 |
gigaUpgradeSoftware OBJECT IDENTIFIER .1.3.6.1.4.1.36.2.15.3.3.3.3 |
doTransfer OBJECT IDENTIFIER .1.3.6.1.4.1.36.2.15.3.3.3.3.1 |
tftpDestinationThis object is the IP address of the host
storing the file containing the software image.
The object may not be set until the last requested
transfer succeeds or fails. So, before setting
this object the user should verify that
transferStatus does not have the value
'requested' or 'inProgress'.rw IpAddress .1.3.6.1.4.1.36.2.15.3.3.3.3.1.1 |
mopDestinationThis object is the 802 48-bit address of the host
storing the file containing the software image.
The object may not be set until the last requested
transfer succeeds or fails. So, before setting this
object, the user should verify that transferStatus
does not have the value 'requested' or 'inProgress'.
Both version 3 and version 4 of MOP are supported.
If a unicast address is specified, the transfer will
be from that host. If the MOP multicast address
ab-00-00-01-00-00 is used, the transfer will be from
the first MOP server to respond, as usual.rw OCTET STRING .1.3.6.1.4.1.36.2.15.3.3.3.3.1.2 |
transferFileNameThis object is the name of the file containing
the software image.
The object may not be set until the last requested
transfer succeeds or fails. Before setting this
object, the user should verify that transferStatus
does not have the value 'requested' or 'inProgress'.
Further, this object may not be set until the last
requested copy succeeds or fails. Before setting
this object, the user should verify that copyStatus
does not have the value 'requested' or 'inProgress'.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.36.2.15.3.3.3.3.1.3 |
transferActionTo initiate a transfer of a file from a
server to the SCP, set this object.
If transferFileName is non-empty, and
mopDestination is non-zero, setting this
object to doMOP(2) will cause a MOP
'load' to be attempted.
If transferFileName is non-empty, and
tftpDestination is non-zero, setting this
object to doTFTP(3) will cause a TFTP
'Get' to be attempted.
This object may not be set until the last
requested transfer succeeds or fails, and the
last requested copy succeeds or fails. So,
before setting this object the user should
verify that transferStatus does not have the
values 'requested' or 'inProgress', and that
copyStatus does not have the values
'requested' or 'inProgress'.rw Enumeration .1.3.6.1.4.1.36.2.15.3.3.3.3.1.4 |
transferStatusThis variable can be polled to determine when the
transfer has completed. Polling for completion allows
other SNMP requests to be processed while the transfer
is in progress (the SNMP is single-threaded).ro Enumeration .1.3.6.1.4.1.36.2.15.3.3.3.3.1.5 |
transferSizeSize in bytes of the transfered file. This object
can be polled along with the transferStatus object to
monitor the progress of the transfer.ro INTEGER .1.3.6.1.4.1.36.2.15.3.3.3.3.1.6 |
useTransfer OBJECT IDENTIFIER .1.3.6.1.4.1.36.2.15.3.3.3.3.2 |
copyToSlotThe slot number of the card which is to be
upgraded.
The object may not be set until the last requested
copy succeeds or fails.rw INTEGER .1.3.6.1.4.1.36.2.15.3.3.3.3.2.1 |
copyTypeThe type of the image.
The object is set after a transfer succeeds or fails.ro Enumeration .1.3.6.1.4.1.36.2.15.3.3.3.3.2.2 |
copyActionTo initiate a software upgrade of a card, set
this object.
If copyToSlot is non-zero, and
copyType has a value other than
'none', and transferStatus has the value
'success', a software upgrade of the card is
attempted.
The handler double-checks that the slot requires
software of the expected type, and provides
demultiplexing when multiple images may be sent to
the same slot. The power system controller is updated
by sending its image to the clock card slot.
The object may not be set until the last requested
transfer succeeds, and the last requested copy
succeeds or fails.
Reading this object always returns the value
none(1).rw Enumeration .1.3.6.1.4.1.36.2.15.3.3.3.3.2.3 |
copyStatusThis variable can be polled to determine when the
card upgrade has completed. Polling for completion
allows other SNMP requests to be processed while the
copy is in progress (the SNMP is single-threaded).ro Enumeration .1.3.6.1.4.1.36.2.15.3.3.3.3.2.4 |
deleteTransferWhen read, this object indicates whether the result of
a file transfer is still present. The value exists
indicates that the transferred file is present; the
value notExist indicates that no file has been
transferred or that it has been deleted.
Writing the value exists is an error. Writing the
value notExist deletes the transferred file.
The object may not be set until the last requested
transfer succeeds or fails. It may not be set while
a copy is in progress, either.rw Enumeration .1.3.6.1.4.1.36.2.15.3.3.3.3.3 |
gigaIP OBJECT IDENTIFIER .1.3.6.1.4.1.36.2.15.3.3.3.4 |
arpTimingMechanism OBJECT IDENTIFIER .1.3.6.1.4.1.36.2.15.3.3.3.4.1 |
arpTimeoutInSecondsThe maximum amount of time an IP to LAN address
translation will be used if it cannot be re-verified.rw INTEGER .1.3.6.1.4.1.36.2.15.3.3.3.4.1.1 |
arpPeriodBetweenRequestsThe time, in seconds, between ARP requests that
are used to verify or to discover an IP to LAN address
translation.rw INTEGER .1.3.6.1.4.1.36.2.15.3.3.3.4.1.2 |
arpRequestRetriesThe number of times ARP requests are used to verify
or to discover an IP to LAN address translation.rw INTEGER .1.3.6.1.4.1.36.2.15.3.3.3.4.1.3 |
snmpParameters OBJECT IDENTIFIER .1.3.6.1.4.1.36.2.15.3.3.3.4.2 |
snmpDuplicateDiscardIntervalIf duplicated snmp messages arrive within this
interval, all but the first one will be discarded.
The unit is a hundredth of second.rw INTEGER .1.3.6.1.4.1.36.2.15.3.3.3.4.2.1 |
arpControlParams OBJECT IDENTIFIER .1.3.6.1.4.1.36.2.15.3.3.3.4.3 |
arpAgentWhen true, the GIGAswitch will service broadcast
ARP requests from its ARP cache.
When false, Broadcast ARP frames are flooded.rw Enumeration .1.3.6.1.4.1.36.2.15.3.3.3.4.3.1 |
arpStatisticalCounters OBJECT IDENTIFIER .1.3.6.1.4.1.36.2.15.3.3.3.4.4 |
arpStatisticalTableThis table stores ARP counters. SEQUENCE OF ArpStatisticalEntry .1.3.6.1.4.1.36.2.15.3.3.3.4.4.1 |
arpStatisticalEntryInformation about the ARP statistical table is stored. ArpStatisticalEntry .1.3.6.1.4.1.36.2.15.3.3.3.4.4.1.1 |
arpStatisticalIfIndexIdentifies the Interface. The value of this object is
the same as the ifIndex, defined in MIB-II, for this
interface.ro INTEGER .1.3.6.1.4.1.36.2.15.3.3.3.4.4.1.1.1 |
arpUnicastReceivedUnicast ARP requests received on this port.ro Counter .1.3.6.1.4.1.36.2.15.3.3.3.4.4.1.1.2 |
arpBroadcastReceivedBroadcast ARP requests received on this port.ro Counter .1.3.6.1.4.1.36.2.15.3.3.3.4.4.1.1.3 |
arpRepliesTransmittedARP replies transmitted on this port.ro Counter .1.3.6.1.4.1.36.2.15.3.3.3.4.4.1.1.4 |
arpFramesFloodedARP frames received on this port that required
flooding while acting as an ARP agent.ro Counter .1.3.6.1.4.1.36.2.15.3.3.3.4.4.1.1.5 |
arpFramesDiscardedARP frames received on this port that were discarded
due to protocol errors.ro Counter .1.3.6.1.4.1.36.2.15.3.3.3.4.4.1.1.6 |
ipSwitching OBJECT IDENTIFIER .1.3.6.1.4.1.36.2.15.3.3.3.4.5 |
ipSwitchEnableIf true then switched IP filtering is enabled. If
false switched IP filtering is disabled.rw Enumeration .1.3.6.1.4.1.36.2.15.3.3.3.4.5.1 |
ipSwitchPortsTableThis table allows the user to assign an address
range to logical bridge ports so that all traffic
destined to addresses within that range will go out
those ports. SEQUENCE OF IpSwitchPortsEntry .1.3.6.1.4.1.36.2.15.3.3.3.4.5.2 |
ipSwitchPortsEntryAn entry that stores information about a switched
IP filtering range. IpSwitchPortsEntry .1.3.6.1.4.1.36.2.15.3.3.3.4.5.2.1 |
ipRangeStartAddrAn index for the ipSwitchPortsTable. This is the
start address of the range of addresses for which
the the ipStaticPorts and ipDynamicPorts are
valid.ro IpAddress .1.3.6.1.4.1.36.2.15.3.3.3.4.5.2.1.1 |
ipRangeEndAddrAn index for the ipSwitchPortsTable. This is the
end address of the range of addresses for which the
the ipStaticPorts and ipDynamicPorts are valid.ro IpAddress .1.3.6.1.4.1.36.2.15.3.3.3.4.5.2.1.2 |
ipIPAddrThe IP address associated with the range, ipRangeStartAddr
and ipRangeEndAddr.ro IpAddress .1.3.6.1.4.1.36.2.15.3.3.3.4.5.2.1.3 |
ipStaticPortsipStaticPorts is the set of logical ports that
packets will exit the Gigaswitch when the
destination address is within the range specified
by ipRangeStartAddr and ipRangeEndAddr.
ipStaticPorts is expressed using a shorthand
that specifies which logical ports are assigned
to the address range.
An example of a specification would be
(1,6-9,21),
where commas separate logical ports and hyphens are
short-hand for specifying a range of numbers. This
example would assign logical ports 1,6,7,8,9, and 21
to the specified address/mask.
Logical port numbers are specified in decimal.
The ipStaticPorts will read back in a form
equivalent to the form written. It may not read
back exactly as written.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.36.2.15.3.3.3.4.5.2.1.4 |
ipDynamicPortsipDynamicPorts is the set of logical ports, learned
dynamically, that packets will exit the Gigaswitch
when the destination address is within the range
specified by ipRangeStartAddr and ipRangeEndAddr.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.36.2.15.3.3.3.4.5.2.1.5 |
ipPrimaryPortsipPrimaryPorts is the set of all logical ports,
set by management, that packets will exit the
Gigaswitch regardless of the range to which they
are addressed to.
The ipPrimaryPorts is expressed using a shorthand that
specifies the logical ports.
An example of a specification would be
(1,6-9,21)
where commas separate logical ports and hyphens are
short-hand for specifying a range of numbers. This
example would assign logical ports 1,6,7,8,9, and 21
to the specified address/mask.
Logical port numbers are specified in decimal.
The ipPrimaryPorts will read back in a form
equivalent to the form written. It may not read
back exactly as written.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.36.2.15.3.3.3.4.5.3 |
ipDynamicPrimaryPortsipPrimaryPorts is the set of all logical ports,
learned dynamically, that packets will exit the
Gigaswitch regardless of the range to which they
are addressed to.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.36.2.15.3.3.3.4.5.4 |
ipDynamicEnabledPortsipSwitchDynamicEnabledPorts is the set of bridge
ports over which the GIGAswitch sends and receives
information about configured IP address ranges.
The syntax used to specify it is the same as for
ipPrimaryPorts.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.36.2.15.3.3.3.4.5.5 |
gigaSets OBJECT IDENTIFIER .1.3.6.1.4.1.36.2.15.3.3.3.5 |
portGroupMembershipTableThe table for storing the port group membership. SEQUENCE OF PortGroupMembershipEntry .1.3.6.1.4.1.36.2.15.3.3.3.5.1 |
portGroupMembershipEntryAn entry stores information about a single port
group. PortGroupMembershipEntry .1.3.6.1.4.1.36.2.15.3.3.3.5.1.1 |
portGroupBridgePortThe port group port number. It is unique within this table
and must be between 37 and 64. Without
management settings, the port group has no members in it.ro INTEGER .1.3.6.1.4.1.36.2.15.3.3.3.5.1.1.1 |
portGroupMembershipThis object displays the current state of the port group
membership. Managers specify a new port group membership
using portGroupMembershipWorkBuf. The new membership
becomes effective and remains unchanged after a system crash
when portGroupAction is set to doUpdate and the updating
process succeeds.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.36.2.15.3.3.3.5.1.1.2 |
portGroupMembershipWorkBufManagers can update a new port group membership as many
times as they want using this object. Setting this object
to a new value does not change the current membership and
the value will be resetted after a system crash. The new
value is copied to portGroupMembership when portGroupAction
is set to doUpdate and the updating process successfully
changes the port member.
A port group is expressed using a shorthand that says what
bridge ports are members of the group.
An examples of a specification is:
(1,3,5)
(32-36)
(6,12-24,36)
()
A list of bridge ports between 1 and 36 are used
to represent the members of the port group. A bridge port
becoming a member of a port group ceases to operate as a
normal bridge port, therefore filters on the port have no
effect. If a port group is specified as an empty set, the
members in the group will operate as normal bridge ports and
take their original brige port numbers. Their original filters
will also become effective.
Commas separate items in a list of bridge ports. Hyphens are
short-hand for specifying a range of numbers. Bridge port
numbers are specified in decimal.
A port group will read back in a form equivalent to the form
written. It may not read back exactly as written.
If the manager specifies a member that is overlapped with a
member of a preexisting port group in the same object,
setting portGroupAction to doUpdate will fail.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.36.2.15.3.3.3.5.1.1.3 |
portGroupPortTypeThis object displays the current state of the port group
port type. Managers specify a new port group port type
using portGroupPortTypeWorkBuf. The new port type becomes
effective and remains unchanged after a system crash
when portGroupAction is set to doUpdate and the updating
process succeeds.ro Enumeration .1.3.6.1.4.1.36.2.15.3.3.3.5.1.1.4 |
portGroupPortTypeWorkBufManagers can update a new port group port type as many
times as they want using this object. Setting this object
to a new value does not change the current port type and
the value will be resetted after a system crash. The new
value is copied to portGroupPortType when portGroupAction
is set to doUpdate and the updating process successfully
changes the port type.
Two port group types are supported: 1) the hunt group and
2) the reliability group.
All members in the hunt group port work like a single bridge
port as far as the bridge functions are concerned and yet
provides higher bandwidth due to multiple parallel FDDI links.
A state of a port in a reliability group is either
operational or backup. Only a single port in the group
may be operational, while the other ports in the group
are backup. When the operational port fails, one backup
mode port will be selected, and quickly become operational.rw Enumeration .1.3.6.1.4.1.36.2.15.3.3.3.5.1.1.5 |
portGroupPortOperStatusThis object indicates the operational status of the port group.
The status represents the aggregated effect of each member's
status.
uninitializedPort(1) state indicates one of the followings:
1) the port group has no member in it,
2) no port in the port group is powered on,
3) no port in the port group has successfully
completed startup diagnostics.
State preBridging(2) means that some ports in the port group
have been initialized with the bridge functions, but no port
is not yet functioning as part of a bridge port. This is
always the case if the datalink is not up. A hunt group
member remains in this state if the remote end of the link
is not properly configured as part of the hunt group. An
inactive member of a reliability group is also in this state
if it is up and initialized.
State bridging(3) means that at least one port in the port
group is functioning as part of a bridge port. The port
group must be in this state to carry user data.ro Enumeration .1.3.6.1.4.1.36.2.15.3.3.3.5.1.1.6 |
portGroupFppnMembershipTableThe table for storing the port group membership
specified by FPPN numbers. SEQUENCE OF PortGroupFppnMembershipEntry .1.3.6.1.4.1.36.2.15.3.3.3.5.2 |
portGroupFppnMembershipEntryAn entry stores information about a single port
group. PortGroupFppnMembershipEntry .1.3.6.1.4.1.36.2.15.3.3.3.5.2.1 |
portGroupFppnPortThe port group port number. It is unique within this table
and must be between 99.37 and 99.64. Without management
settings, the port group has no members in it.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.36.2.15.3.3.3.5.2.1.1 |
portGroupFppnMembershipThis object displays the current state of the port group
membership. Managers specify a new port group membership
using portGroupFppnMembershipWorkBuf. The new membership
becomes effective and remains unchanged after a system crash
when portGroupAction is set to doUpdate and the updating
process succeeds.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.36.2.15.3.3.3.5.2.1.2 |
portGroupFppnMembershipWorkBufManagers can update a new port group membership as many
times as they want using this object. Setting this object
to a new value does not change the current membership and
the value will be resetted after a system crash. The new
value is copied to portGroupFppnMembership when portGroupAction
is set to doUpdate and the updating process successfully
changes the port member.
A port group is expressed using a shorthand that says what
FPPN ports are members of the group.
An examples of a specification is:
(1.1,3.2,5.1)
(13.1-14.2)
(4.1,11.1-13.2,14.2)
()
A list of FPPN ports between 1.1 and 14.2 are used to
represent the members of the port group. A port becoming
a member of a port group ceases to operate as a normal
bridge port, therefore filters on the port have no effect.
If a port group is specified as an empty set, the members in
the group will operate as normal bridge ports and take their
original FPPN port numbers. Their original filters will
also become effective.
Commas separate items in a list of FPPN ports. Hyphens are
short-hand for specifying a range of numbers. FPPN port
numbers are of the form (slot.port) where slot is the slot
number and port is the port number in the slot.
A port group will read back in a form equivalent to the form
written. It may not read back exactly as written.
If the manager specifies a member that is overlapped with a
member of a preexisting port group in the same object,
setting portGroupAction to doUpdate will fail.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.36.2.15.3.3.3.5.2.1.3 |
portGroupFppnPortTypeThis object displays the current state of the port group
port type. Managers specify a new port group port type
using portGroupPortTypeWorkBuf. The new port type becomes
effective and remains unchanged after a system crash
when portGroupAction is set to doUpdate and the updating
process succeeds.ro Enumeration .1.3.6.1.4.1.36.2.15.3.3.3.5.2.1.4 |
portGroupFppnPortTypeWorkBufManagers can update a new port group port type as many
times as they want using this object. Setting this object
to a new value does not change the current port type and
the value will be resetted after a system crash. The new
value is copied to portGroupPortType when portGroupAction
is set to doUpdate and the updating process successfully
changes the port type.
Two port group types are supported: 1) the hunt group and
2) the reliability group.
All members in the hunt group port work like a single bridge
port as far as the bridge functions are concerned and yet
provides higher bandwidth due to multiple parallel FDDI links.
A state of a port in a reliability group is either
operational or backup. Only a single port in the group
may be operational, while the other ports in the group
are backup. When the operational port fails, one backup
mode port will be selected, and quickly become operational.rw Enumeration .1.3.6.1.4.1.36.2.15.3.3.3.5.2.1.5 |
portGroupFppnPortOperStatusThis object indicates the operational status of the port group.
The status represents the aggregated effect of each member's
status.
uninitializedPort(1) state indicates one of the followings:
1) the port group has no member in it,
2) no port in the port group is powered on,
3) no port in the port group has successfully
completed startup diagnostics.
State preBridging(2) means that some ports in the port group
have been initialized with the bridge functions, but no port
is not yet functioning as part of a bridge port. This is
always the case if the datalink is not up. A hunt group
member remains in this state if the remote end of the link
is not properly configured as part of the hunt group. An
inactive member of a reliability group is also in this state
if it is up and initialized.
State bridging(3) means that at least one port in the port
group is functioning as part of a bridge port. The port
group must be in this state to carry user data.ro Enumeration .1.3.6.1.4.1.36.2.15.3.3.3.5.2.1.6 |
portGroupStatusTableThe table for storing the port status. SEQUENCE OF PortGroupStatusEntry .1.3.6.1.4.1.36.2.15.3.3.3.5.3 |
portGroupStatusEntryAn entry stores the port status. PortGroupStatusEntry .1.3.6.1.4.1.36.2.15.3.3.3.5.3.1 |
portGroupStatusBridgePortThe bridge port number runs from 1 to _LASTPHYSPORT_.ro INTEGER .1.3.6.1.4.1.36.2.15.3.3.3.5.3.1.1 |
portGroupStatusPortNumberIf the indexed port is a member of a port group, the port
group number is returned. Otherwise, the index itself is
returned.ro INTEGER .1.3.6.1.4.1.36.2.15.3.3.3.5.3.1.2 |
portGroupStatusPortTypeThis object represents the port type.ro Enumeration .1.3.6.1.4.1.36.2.15.3.3.3.5.3.1.3 |
portGroupStatusOperStatusThis object indicates the operational status of the indexed
port.
uninitializedPort(1) state indicates one of the followings:
1) the port is nonexistent,
2) the port is in a slot that is not powered on,
3) the port has not successfully completed startup diagnostics.
Ports in portInitializing(2) state are in the process of being
initialized. It is a temporary state.
State preBridging(3) means that the port has been initialized
with the bridge functions, but is not functioning as part of a
bridge port. This is always the case if the datalink is not
up. A hunt group member remains in this state if the remote
end of the link is not properly configured as part of the hunt
group. An inactive member of a reliability group is also in
this state if it is up and initialized.
State bridging(4) means that the port is functioning as
part of a bridge port. Ports must be in this state to
carry user data.ro Enumeration .1.3.6.1.4.1.36.2.15.3.3.3.5.3.1.4 |
learningDomainMembershipTableThis table allows learning domains to be created, modified,
and deleted. There can be from 1 to 8 learning domains.
A learning domain is a collection of port groups (or bridge
ports) which share a learning database. Every bridge port
is a member of precisely one learning domain. A MAC address
that is seen on one port of the learning domain will be
taught to the other ports in the learning domain, but not to
ports in other learning domains, unless a target learning
domain has been set up.
Among other things, this allows for the possbility that a
single MAC address may be learned on several different
ports - as long as they are in separate learning domains.
There are a maximum of 8 learning domains, including the
default learning domain. The default learning domain is the
set of all bridge ports that do not belong to a management
defined learning domain. SEQUENCE OF LearningDomainMembershipEntry .1.3.6.1.4.1.36.2.15.3.3.3.5.4 |
learningDomainMembershipEntryA group of objects, indexed by learningDomainNumber,
that specify learning domain attributes. LearningDomainMembershipEntry .1.3.6.1.4.1.36.2.15.3.3.3.5.4.1 |
learningDomainNumberThe index for a learning domain is an integer with
range, 1-8, where 1 is the default learning domain.ro INTEGER .1.3.6.1.4.1.36.2.15.3.3.3.5.4.1.1 |
learningDomainMembershipThis object displays the current state of the learning
domain membership. Managers specify a new learning domain
membership using learningDomainMembershipWorkBuf. The new
membership becomes effective and remains unchanged, across
system reboots, when portGroupAction is set to doUpdate
and the updating process succeeds.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.36.2.15.3.3.3.5.4.1.2 |
learningDomainMembershipWorkBufThe learningDomainMembershipWorkBuf object is used to
create,modify, and delete learning domains.
Managers can update a learning domain membership as many
times as they want using this object. Setting this object
to a new value does not change the current membership nor
the values stored in non-volatile memory until the object
portGroupAction is written with doUpdate. At that time the
new values will be written to learningDomainMembership and
non-volatile memory and the learning domain changes will
take effect.
The addition/removal of bridge ports to/from a learning
domain is an atomic operation. Because a bridge port can
only belong to one learning domain, the last assignment of a
bridge port to a learning domain will determine the learning
domain in which the bridge port resides.
There is a default learning domain, designated by
learningDomainNumber 1, which all bridge ports belong to
until management changes the assignments of bridge ports
to learning domains. If a bridge port is removed from a
learning domain, it is placed back into the default
learning domain. The default learning domain can not be
modified directly. It changes when new learning domains
are created or modified.
Every learning domain is a member of precisely one logical
bridge.
The learningDomainMembership is expressed using a shorthand
that specifies which bridge ports belong in the learning
domain. An example of a specification would be :
(1,6-9,21)
where commas separate bridge ports and hyphens are short-hand
for specifying a range of numbers. This example would assign
bridge ports 1,6,7,8,9, and 21 to the specified learning domain.
Bridge port numbers are specified in decimal.
A learning domain will read back in a form equivalent to the
form written. It may not read back exactly as written.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.36.2.15.3.3.3.5.4.1.3 |
portTargetDomainListMembershipTableThis table allows port target domains lists to be
created, modified, and deleted.
The port target domain list is the set of all mgmt
defined learning domains to which a bridge port, as
specified by the index, will learn addresses from. A
MAC address that is seen in one of the learning
domains in the port target domain list will be learned
by the indexed bridge port.
Every port target domain is a member of precisely one
logical bridge. SEQUENCE OF PortTargetDomainListMembershipEntry .1.3.6.1.4.1.36.2.15.3.3.3.5.5 |
portTargetDomainListMembershipEntryA group of objects, indexed by portTargetDomainListIndex,
that specify port target domain attributes. PortTargetDomainListMembershipEntry .1.3.6.1.4.1.36.2.15.3.3.3.5.5.1 |
portTargetDomainListIndexA bridge port number from 1 - 64 .ro INTEGER .1.3.6.1.4.1.36.2.15.3.3.3.5.5.1.1 |
portTargetDomainListMembershipThe portTargetDomainListMembership specifies a set of
mgmt specified learning domains.
This object displays the current state of the port
target domain list membership. Managers specify a new
port target domain membership, or modify an existing
one using portTargetDomainListMembershipWorkBuf. The
new membership becomes effective and remains unchanged,
across system reboots, when portGroupAction is set to
doUpdate and the updating process succeeds.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.36.2.15.3.3.3.5.5.1.2 |
portTargetDomainListMembershipWorkBufThe portTargetDomainListMembership object is used to
create, modify, and delete port target domain lists.
Managers can update a port target domain membership
list as many times as they want using this object.
Setting this object to a new value does not change the
current membership nor the values stored in mgmt memory
until the object portGroupAction is written with
doUpdate. At that time the new values will be written
to portTargetDomainListMembership and mgmt memory and
the target domain changes will take effect.
The portTargetDomainListMembership specifies the target
domains that a learning domain belongs to. This set of
learning domains is called the port target domain list.
The portTargetDomainListMembership is expressed using a
shorthand that specifies which learning domains belong
in the port target domain list. An example of a
specification would be :
(2-4,6,8)
where commas separate learning domains and hyphens are
short-hand for specifying a range of numbers.. This
example would map the learning domain to the port
target domain list consisting of learning_domains 2, 3,
4, 6, and 8. Valid values for learning domains are 1-8.
A port target domain list will read back in a form
equivalent to the form written. It may not read back
exactly as written.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.36.2.15.3.3.3.5.5.1.3 |
lBDomainMembershipTableThe table for storing the logical bridge domain
membership. SEQUENCE OF LBDomainMembershipEntry .1.3.6.1.4.1.36.2.15.3.3.3.5.6 |
lBDomainMembershipEntryAn entry stores information about a logical bridge
domain. LBDomainMembershipEntry .1.3.6.1.4.1.36.2.15.3.3.3.5.6.1 |
lBDomainNumberThe logical bridge domain number. It is unique within
this table and must be between 1 and 8.ro INTEGER .1.3.6.1.4.1.36.2.15.3.3.3.5.6.1.1 |
lBDomainMembershipThis object displays the learning domain numbers which are
members of the indexed logical bridge domain in the current
box configuration.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.36.2.15.3.3.3.5.6.1.2 |
lBDomainMembershipWorkBufManagers can specify logical bridge domains as many times as
needed without effecting the current box configuration using
this object. Setting this object to a new value is stored
in a local buffer and the changes are not recorded in the
nonvolatile memory.
The new value is copied into lBDomainMembership and
becomes effective when portGroupAction is set to doUpdate
and the updating process successfully upgrades the logical
bridge domains.
A logical bridge domain is expressed using a shorthand that
says what learning domains are members of it.
An examples of a specification is:
(1,3,5)
(2-4)
Commas separate items in a list of learning domains. Hyphens
are short-hand for specifying a range of numbers. Learning
domain numbers are specified in decimal.
A logical bridge domain will read back in a form equivalent to
the form written. It may not read back exactly as written.
Without a management set, the default logical bridge domain
(i.e., domain number 1) contains all learning domains. The
other logical bridge domains are empty sets. A logical
bridge domain is created by specifying what learning domains
are members of it. Specified learning domains are deleted
from the old logical bridge domain and added to the new
logical bridge domain. Deletion and addition of the learning
domains are atomic across the SNMP messages. Learning domains
left out in the specification will automatically join the
default logical bridge domain.
Reconfiguring logical bridge domains is an expensive operation.
Therefore the manager should not change the configuration
very often.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.36.2.15.3.3.3.5.6.1.3 |
portGroupActionTo initiate a configuration upgrade of a box, set
this object.
The tables updated with this set operation are:
portGroupMembershipTable,
learningDomainMembershipTable,
portTargetDomainListMembershipTable,
lBDomainMembershipTable
The handler checks the consistency of the manager's
configuraton of the box specified in the tables'
working buffer. If no configuraton error is detected,
the box starts the reconfiguration process and the
working buffers are copied into their corresponding
variables. The changes will survive after a system
crash.
Reading this object always returns the value none(1).rw Enumeration .1.3.6.1.4.1.36.2.15.3.3.3.5.7 |
portGroupActionStatusThis object shows the result of the most recent
setting of portGroupAction to doUpdate(2).ro Enumeration .1.3.6.1.4.1.36.2.15.3.3.3.5.8 |
trafficGroupMembershipTableThis table allows the user to add and delete physical ports
to traffic groups. There can be from 1 to 16 traffic groups.
A traffic group is a collection of physical ports that is
used to allow single path traffic coming in on physical
ports to be transmitted out a single management assigned
member port of a hunt group. This is used to restrict single
path traffic from being multipathed in a hunt group.
Every physical port must belong to one of 16 traffic groups.
Traffic group 1 is the default traffic group. All ports
that do not belong to traffic groups 2-16 belong to the
default traffic group. SEQUENCE OF TrafficGroupMembershipEntry .1.3.6.1.4.1.36.2.15.3.3.3.5.9 |
trafficGroupMembershipEntryAn entry that stores information about a traffic group. TrafficGroupMembershipEntry .1.3.6.1.4.1.36.2.15.3.3.3.5.9.1 |
trafficGroupNumberThe index for the traffic group membership is a traffic
group number. Traffic group numbers are in the range 1-16.
Traffic group 1 is the default traffic group.ro INTEGER .1.3.6.1.4.1.36.2.15.3.3.3.5.9.1.1 |
trafficGroupMembershipThe trafficGroupMembership object allows the user to add
and delete physical ports from traffic groups.
Because a physical port can only belong to one traffic
group, the last assignment of a physical port to a traffic
group will determine the traffic group in which the
physical port is a member.
There is a default traffic group which physical ports
belong to until management changes the assignments of
physical ports to traffic groups. If a physical port is
removed from a traffic group, it is placed back into
the default traffic group. The default traffic group
can not be modified directly. It changes when new
traffic groups are added or removed from other traffic
groups. The default traffic group is traffic group 1.
The trafficGroupMembership is expressed using a shorthand
that specifies which physical ports belong in the traffic
group. An example of a specification would be :
(1,6-9,21)
where commas separate physical ports and hyphens are short-
hand for specifying a range of numbers. This example would
assign physical ports 1,6,7,8,9, and 21 to the specified
traffic group.
Physical port numbers are specified in decimal.
A traffic group will read back in a form equivalent to the
form written. It may not read back exactly as written.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.36.2.15.3.3.3.5.9.1.2 |
trafficGroupAttributeTableThis table allows traffic group attributes to be set. SEQUENCE OF TrafficGroupAttributeEntry .1.3.6.1.4.1.36.2.15.3.3.3.5.10 |
trafficGroupAttributeEntryAn entry that stores traffic group attributes. TrafficGroupAttributeEntry .1.3.6.1.4.1.36.2.15.3.3.3.5.10.1 |
trafficGroupNumOne of two indexes into the trafficGroupAttributeTable.
It is within the range 1-16.ro INTEGER .1.3.6.1.4.1.36.2.15.3.3.3.5.10.1.1 |
trafficGroupHgNumberSecond of two indexes into the trafficGroupAttributeTable.
This is the hunt group that all ports in the traffic group
are assigned to and is in the range 37-64.ro INTEGER .1.3.6.1.4.1.36.2.15.3.3.3.5.10.1.2 |
trafficGroupHgMemberThe trafficGroupHgMember is a number in the range 1-16
that maps to a member of the hunt group specified by
trafficGroupHgNumber. trafficGroupHgMember 1 maps to the
lowest numbered member of the hunt group,
trafficGroupHgMember 2 maps to the second lowest
numbered member of the hunt group, etc. If the
trafficGroupHgMember is greater then the number of
members in the hunt group, then it wraps.
For example :
Given that traffic groups 1,2,3,4,5 all have physical
ports.
hunt group 37 = {3,6,8}
For hunt group 37 :
traffic group 1 set to member number 1
traffic group 2 set to member number 2
traffic group 3 set to member number 3
traffic group 4 set to member number 4
traffic group 5 set to member number 5
then
trafficGroupHgMember 1 maps to port 3
trafficGroupHgMember 2 maps to port 6
trafficGroupHgMember 3 maps to port 8
trafficGroupHgMember 4 maps to port 3
trafficGroupHgMember 5 maps to port 6rw INTEGER .1.3.6.1.4.1.36.2.15.3.3.3.5.10.1.3 |
trafficGroupCategoryThe trafficGroupCatagory is defined as follows :
fixed
-
fixed means that traffic is to stay on the same port until
the port fails. For this value, the member number is
ignored completely. The first physical port that comes up
in the hunt group will be assigned the traffic. If the port
fails the lowest numbered remaining member of the hunt group
will be assigned the traffic. If the traffic category is fixed,
sequential delivery of packets is almost guaranteed.
reconfig
reconfig means that the traffic group may be moved from one
hunt group member to another whenever any port joins or
leaves the hunt group. If possible, the traffic group must
use the hunt group member whose trafficGroupHgMember is
configured. If the traffic category is reconfig, sequential
delivery of packets is guaranteed, except when members enter
or leave the hunt group.rw Enumeration .1.3.6.1.4.1.36.2.15.3.3.3.5.10.1.4 |
learningQuotaTableEach logical bridge domain (LBD) has a learning quota. This table
allows the setting of theses quotas. SEQUENCE OF LearningQuotaEntry .1.3.6.1.4.1.36.2.15.3.3.3.5.11 |
learningQuotaEntryA group of objects, indexed by learningQuotaNumber,
that specify learning quotas. LearningQuotaEntry .1.3.6.1.4.1.36.2.15.3.3.3.5.11.1 |
learningQuotaNumberThe index for a learning quota is a learning domain with
range, 1 - 8.ro INTEGER .1.3.6.1.4.1.36.2.15.3.3.3.5.11.1.1 |
learningQuotaEach learning domain has a learning quota. The ports in the
domain are guaranteed the ability to use approximately this
number of address entries in the Translation Table, so that
an excessive number of learned addresses in one domain cannot
interfere significantly with learning in another domain. The
GIGAswitch keeps track of the count of addresses learned in
each domain and deletes addresses from the domains that have
most exceeded their learning quotas to make room for
addresses learned in other domains. If these quotas are
configured so that they add up to less than the size of the
SCP Translation Table, there are almost always SCP
Translation Table entries available to accommodate new
learned addresses. Further, these addresses will not be
deleted to make room for others unless the domain's quota is
reached or is close to being reached.
If the SCP Translation Table is not full, the quotas are
allowed to be exceeded. Under such circumstances, the count
of learned addresses in a logical bridge may grow until it is
close to the number of unused entries in the Translation
Table plus the applicable learning quota. The learning
quotas are not exact, and addresses may start to be deleted
when this limit is within a small number of addresses
(initially 100) of being reached.
It should be remembered that there are factors other than the
learning quotas that may restrict the number of addresses
that can be learned, so that a high learning quota does not
guarantee that number of addresses may be learned. In
particular:
1) If the capacity of the linecard Translation Tables is
exceeded, no more addresses may be learned on that linecard.
2) If the sum of the configured learning quotas is greater
than the SCP Translation Table size, then no more addresses
may be learned once the SCP Translation Table is full, even
though no quota may have been exceeded.
When either of these situations occur, an attempt is made to
solve the problem by deleting addresses in the same manner as
when dealing with the learning quota limits.
The default value for each learning quota is 32768, the same
as the capacity of the SCP Translation Table. This large
value means that the quotas have no effect. To see the full
benefit of learning quotas, they should be set so that the
sum of the quotas over all active domains is less than 32500.rw INTEGER .1.3.6.1.4.1.36.2.15.3.3.3.5.11.1.2 |
gigaSnmpDebug OBJECT IDENTIFIER .1.3.6.1.4.1.36.2.15.3.3.3.6 |
commitFailsExercise abort undo code in SNMP commit processingrw INTEGER .1.3.6.1.4.1.36.2.15.3.3.3.6.1 |
gigaXglEthernetGroup OBJECT IDENTIFIER .1.3.6.1.4.1.36.2.15.3.3.3.7 |
xglTableThis table contains miscellaneous objects for
configuring Fast Ethernet interfaces. SEQUENCE OF XglEntry .1.3.6.1.4.1.36.2.15.3.3.3.7.1 |
xglEntryData for a particular Fast Ethernet interface.
This table may be optionally implemented in such a
way as to allow pre-configuration of hardware which
has not yet been installed. XglEntry .1.3.6.1.4.1.36.2.15.3.3.3.7.1.1 |
xglCompliantMtuWhen true, packets with a data unit of size <=
1500 bytes are sent and received.
When false, packets with a data unit of size <=
1535 bytes are sent and received.rw Enumeration .1.3.6.1.4.1.36.2.15.3.3.3.7.1.1.1 |
xglDisableIcmpErrorsWhen true(1), ICMP redirect message processing is
disabled for the specified port.rw Enumeration .1.3.6.1.4.1.36.2.15.3.3.3.7.1.1.2 |
xglTxErrorsToIcmpFifoWhen true(1), transmit errors are sent to the ICMP
FIFO.rw Enumeration .1.3.6.1.4.1.36.2.15.3.3.3.7.1.1.3 |
xglRxErrorsToIcmpFifoWhen true(1), receive errors are sent to the ICMP
FIFO.rw Enumeration .1.3.6.1.4.1.36.2.15.3.3.3.7.1.1.4 |
xglEnableAppletalkArpIIWhen true(1), enables Appletalk ARP II support.rw Enumeration .1.3.6.1.4.1.36.2.15.3.3.3.7.1.1.5 |
xglEnableRawIPXWhen true(1), enables raw IPX support.rw Enumeration .1.3.6.1.4.1.36.2.15.3.3.3.7.1.1.6 |
agl OBJECT IDENTIFIER .1.3.6.1.4.1.36.2.15.3.3.4 |
aglConfig OBJECT IDENTIFIER .1.3.6.1.4.1.36.2.15.3.3.4.1 |
aglInterfaceConfTableThis table contains the AGL specific interface
configuration parameters, one entry per ATM
interface port. SEQUENCE OF AglInterfaceConfEntry .1.3.6.1.4.1.36.2.15.3.3.4.1.1 |
aglInterfaceConfEntryThis list contains ATM interface configuration
parameters and state variables. AglInterfaceConfEntry .1.3.6.1.4.1.36.2.15.3.3.4.1.1.1 |
aglInterfaceIndexThe value of this object identifies the AGL port
interface for which this entry contains management
information.ro INTEGER .1.3.6.1.4.1.36.2.15.3.3.4.1.1.1.1 |
aglInterfacePhyTypeIndicates the type of physical interface used on the
ATM port. Two physical layer types are supported:
1. STS3c/STM1
2. DS3/E3
The type is unknown if the port is not present or
its physical layer type is not known.ro Enumeration .1.3.6.1.4.1.36.2.15.3.3.4.1.1.1.2 |
aglInterfaceTrafficRateGranularityIndicates the granularity in cell/s for assigning
peak, average and minimum guaranteed rates for
traffic shaped circuits on the AGL port. This value
also represents the minimum rate in cells/s that can
be assigned to a circuit. The rates subscribed to in
the aglVCConnectionTable will be set to a multiple
of this rate.ro INTEGER .1.3.6.1.4.1.36.2.15.3.3.4.1.1.1.3 |
aglSonet OBJECT IDENTIFIER .1.3.6.1.4.1.36.2.15.3.3.4.2 |
aglInterfaceSonetTableThis table contains the AGL specific interface
configuration parameters for the SONET/SDH physical
layer. SEQUENCE OF AglInterfaceSonetEntry .1.3.6.1.4.1.36.2.15.3.3.4.2.1 |
aglInterfaceSonetEntryThis list contains SONET/SDH interface configuration
parameters and state variables. AglInterfaceSonetEntry .1.3.6.1.4.1.36.2.15.3.3.4.2.1.1 |
aglInterfaceSonetIndexThe value of this object identifies the AGL
port interface for which this entry contains
management information and is the same as
aglInterfaceIndex.ro INTEGER .1.3.6.1.4.1.36.2.15.3.3.4.2.1.1.1 |
aglInterfaceSonetModeSpecifies whether the PHY operates in SONET STS-3c
or SDH STM-1 mode. The following code points are
used:
1 SONET STS-3c
2 SDH STM-1rw Enumeration .1.3.6.1.4.1.36.2.15.3.3.4.2.1.1.2 |
aglInterfaceSonetTimingSpecifies whether the PHY operates in loop-timing
or local-timing mode. In loop-timing, the recovered
clock from the receive signal is used directly to
time transmit data. Hence, the PHY is synchronized
to the far-end transmitter. In local timing, transmit
data is timed from a local oscillator of frequency
155.52 MHz (20ppm). The following code points are
used:
1 loop-timing
2 local-timingrw Enumeration .1.3.6.1.4.1.36.2.15.3.3.4.2.1.1.3 |
aglDS3E3 OBJECT IDENTIFIER .1.3.6.1.4.1.36.2.15.3.3.4.3 |
aglInterfaceDS3E3TableThis table contains the AGL specific interface
configuration parameters for the DS3/E3 physical
layer. SEQUENCE OF AglInterfaceDS3E3Entry .1.3.6.1.4.1.36.2.15.3.3.4.3.1 |
aglInterfaceDS3E3EntryThis list contains DS3/E3 interface configuration
parameters and state variables. AglInterfaceDS3E3Entry .1.3.6.1.4.1.36.2.15.3.3.4.3.1.1 |
aglInterfaceDS3E3IndexThe value of this object identifies the AGL
port interface for which this entry contains
management information and is the same as
aglInterfaceIndex.ro INTEGER .1.3.6.1.4.1.36.2.15.3.3.4.3.1.1.1 |
aglInterfaceDS3E3ModeSpecifies whether the DS3/E3 PHY operates in low
power mode for short distances or high power mode
for longer distances. The following code points are
used:
1 low-power
2 high-powerrw Enumeration .1.3.6.1.4.1.36.2.15.3.3.4.3.1.1.2 |
aglInterfaceDS3E3PlcpSpecifies whether ATM cells may be mapped into
the DS3 PLCP. In the enabled mode, PLCP framing
and timing is applied to each ATM cell.rw Enumeration .1.3.6.1.4.1.36.2.15.3.3.4.3.1.1.3 |
aglAtm OBJECT IDENTIFIER .1.3.6.1.4.1.36.2.15.3.3.4.4 |
aglVCConnectionTableThis table contains AGL ATM VCC configuration
and performance parameters and state variables.
Each entry represents a bidirectional traffic
flow. SEQUENCE OF AglVCConnectionTableEntry .1.3.6.1.4.1.36.2.15.3.3.4.4.1 |
aglVCConnectionTableEntryA bidirectional circuit. AglVCConnectionTableEntry .1.3.6.1.4.1.36.2.15.3.3.4.4.1.1 |
aglVCConnectionPortAThe value of this object identifies the AGL
ATM port A of the VCC segment for FDDI-bridged
and ATM-to-ATM circuit types.ro INTEGER .1.3.6.1.4.1.36.2.15.3.3.4.4.1.1.1 |
aglVCConnectionPortAVpiThe VPI value at port A for the bidirectional
circuit. The maximum VPI value cannot exceed
the number supported by the atmInterfaceMaxVpiBits
at AGL ATM port A. This value is used for both
transmit and receive VPIsro INTEGER .1.3.6.1.4.1.36.2.15.3.3.4.4.1.1.2 |
aglVCConnectionPortAVciThe VCI value at the port A for the
bidirectional circuit. The VCI values from 0
to 31 are reserved. The maximum VCI value
cannot exceed the number supported by the
atmInterfaceMaxVciBits specified for the AGL
ATM port A. This value is used for both
transmit and receive VCIsro INTEGER .1.3.6.1.4.1.36.2.15.3.3.4.4.1.1.3 |
aglVCConnectionPortBThe value of this object identifies the AGL
ATM port B of the VCC segment for ATM-to-ATM
circuit types. For FDDI-bridged circuit types
this value should be zero.ro INTEGER .1.3.6.1.4.1.36.2.15.3.3.4.4.1.1.4 |
aglVCConnectionPortBVpiThe VPI value at port B for the bidirectional
ATM-to-ATM circuit. The maximum VPI value
cannot exceed the number supported by the
atmInterfaceMaxVpiBits at AGL ATM port B.
This value is used for both transmit and receive
VPIs. For other circuit types this value should be
zero.ro INTEGER .1.3.6.1.4.1.36.2.15.3.3.4.4.1.1.5 |
aglVCConnectionPortBVciThe VCI value at the port B for the
bidirectional ATM-to-ATM circuit. The VCI values
from 0 to 31 are reserved. The maximum VCI value
cannot exceed the number supported by the
atmInterfaceMaxVciBits specified for the AGL
ATM port B. This value is used for both transmit
and receive VCIs. For other circuit types this value
should be zero.ro INTEGER .1.3.6.1.4.1.36.2.15.3.3.4.4.1.1.6 |
aglVCConnectionTableEntryStatusThe status column used for creating,
and deleting bidirectional circuit
entries in the agl virtual channel
connection table.rw Enumeration .1.3.6.1.4.1.36.2.15.3.3.4.4.1.1.7 |
aglVCConnectionTrafficTypeThe value of this object identifies the circuit
type and characteristics of a particular circuit.
There are two types of connections supported:
1. FDDI-bridged
2. ATM-to-ATM
An FDDI-bridged circuit carries all bridged FDDI
traffic on AGL ATM port A. No information is required
to be entered for Port B. Only one bridged FDDI
circuit per AGL ATM port is supported. The packet
format on this circuit is VC based multiplexed
bridged FDDI as per RFC 1483.
An ATM-to-ATM circuit carries arbitrary packet types
between circuits specified on Port A and Port B of
the GIGAswitch. Multiple ATM-to-ATM circuits are
supported per AGL ATM port.rw Enumeration .1.3.6.1.4.1.36.2.15.3.3.4.4.1.1.8 |
aglVCConnectionAALTypeThe value of this object identifies the AAL type
that should be used on a particular circuit.rw Enumeration .1.3.6.1.4.1.36.2.15.3.3.4.4.1.1.9 |
aglVCConnectionOperStatusThis object indicates the operational status
of the VCC, i.e., whether the managed VCC
segment is up or down. In the down state,
no cells can get across this VCC segment.
The status is unknown if the OAM is disabled.ro Enumeration .1.3.6.1.4.1.36.2.15.3.3.4.4.1.1.10 |
aglVCConnectionAdminStatusThis object indicates the desired status
of the VCC, i.e., whether the managed VCC
segment is enabled or disabled. In the disabled
state, no cells can be passed across this VCC
segment.rw Enumeration .1.3.6.1.4.1.36.2.15.3.3.4.4.1.1.11 |
aglVCConnectionTrafficShaperPeakRateThe value of this object specifies the peak rate in
cells/s that should be used on a particular circuit.
The peak rate will be set to a multiple of the
aglInterfaceTrafficRateGranularity close to the
user specified input.rw INTEGER .1.3.6.1.4.1.36.2.15.3.3.4.4.1.1.12 |
aglVCConnectionTrafficShaperAvgRateThe value of this object specifies the average
(sustained) rate in cells/s that should be used
on a particular circuit. The average rate must be
less than or equal to the peak rate and it will be
set to a multiple of the aglInterfaceTrafficRate-
Granularity close to the user specified input.rw INTEGER .1.3.6.1.4.1.36.2.15.3.3.4.4.1.1.13 |
aglVCConnectionTrafficShaperMinGuaranteedRateThe value of this object specifies the minimum
guaranteed rate in cells/s that should be used
on a particular circuit. For VBR traffic AGL
allows the possibility of overbooking link bandwidth
(up to 1200%) to achive statistical multiplexing.
This parameter specifies the minimum peak bandwidth
that you want to guarantee to the circuit. The
minimum guaranteed rate must be less than or equal
to the peak rate and it will be set to a multiple
of the aglInterfaceTrafficRateGranularity close
to the user specified input.rw INTEGER .1.3.6.1.4.1.36.2.15.3.3.4.4.1.1.14 |
aglVCConnectionTrafficShaperPriorityThe value of this object specifies the priority which
should be given to this circuit in assigning
opportunistic bandwidth that arises from AGL's
bandwidth overbooking policy.rw INTEGER .1.3.6.1.4.1.36.2.15.3.3.4.4.1.1.15 |
aglInterfaceATMTableThis table contains AGL ATM interface specific
settable parameters. SEQUENCE OF AglInterfaceATMTableEntry .1.3.6.1.4.1.36.2.15.3.3.4.4.2 |
aglInterfaceATMTableEntryThe list of settable parameters. AglInterfaceATMTableEntry .1.3.6.1.4.1.36.2.15.3.3.4.4.2.1 |
aglInterfaceATMIndexThe value of this object identifies the AGL port
interface for which this entry contains management
information and is the same as aglInterfaceIndex.rw INTEGER .1.3.6.1.4.1.36.2.15.3.3.4.4.2.1.1 |
aglInterfaceATMScrambeStatusThis object indicates the desired status
of the cell scramble module. In the enabled
state, outgoing cells are scrambed and input
cells are descrambled.rw Enumeration .1.3.6.1.4.1.36.2.15.3.3.4.4.2.1.2 |
aglInterfaceATMOAMStatusThis object indicates the desired status
of the OAM module in the default circuit.
In the enabled state, normal OAM cells
are exchanged between the peers.rw Enumeration .1.3.6.1.4.1.36.2.15.3.3.4.4.2.1.3 |
aglatmMIB OBJECT IDENTIFIER .1.3.6.1.4.1.36.2.15.3.3.5 |
aglatmMIBObjects OBJECT IDENTIFIER .1.3.6.1.4.1.36.2.15.3.3.5.1 |
aglatmInterfaceTrafficEnforcementTypes OBJECT IDENTIFIER .1.3.6.1.4.1.36.2.15.3.3.5.1.1 |
aglatmInterfaceNoTrafficEnforcementThis identifies the no ATM traffic enforcement type.ro OBJECT IDENTIFIER .1.3.6.1.4.1.36.2.15.3.3.5.1.1.1 |
aglatmInterfaceTrafficEnforcementType1This identifies the ATM traffic enforcement type is 1.
For type 1 traffic enforcement, parameter 1
specifies CLP=0+1 peak traffic. Parameters 2, 3, 4
and 5 are not used. The peak rate is measured
in cells per second.ro OBJECT IDENTIFIER .1.3.6.1.4.1.36.2.15.3.3.5.1.1.2 |
aglatmInterfaceTrafficEnforcementType2This identifies the ATM traffic enforcement type is 2.
For type 2 traffic enforcement, parameter 1
specifies CLP=0 peak traffic and parameter
2 specifies CLP=0+1 peak traffic. Parameters 3, 4,
and 5 are not used. The peak rate is measured
in cells per second.ro OBJECT IDENTIFIER .1.3.6.1.4.1.36.2.15.3.3.5.1.1.3 |
aglatmInterfaceTrafficEnforcementType3This identifies the ATM traffic enforcement type is 3.
For type 3 traffic enforcement, parameter 1
specifies CLP=0+1 peak traffic, parameter
2 specifies CLP=0 sustained rate, and parameter 3
specifies CLP=0 maximum burst size. Parameters 4
and 5 are not used. The peak rate is measured
in cells per second. The sustained rate is measured
in cells per second and burst size is measured in cells.ro OBJECT IDENTIFIER .1.3.6.1.4.1.36.2.15.3.3.5.1.1.4 |
aglatmInterfaceTrafficEnforcementType4This identifies the ATM traffic enforcement type is 4.
For type 4 traffic enforcement, parameter 1
specifies CLP=0 peak traffic, parameter
2 specifies CLP=0+1 peak traffic, and parameter 3
specifies tagging (e.g., a value 1 may be
used to indicate tagging). Parameters 4
and 5 are not used. The peak rate is measured
in cells per second.ro OBJECT IDENTIFIER .1.3.6.1.4.1.36.2.15.3.3.5.1.1.5 |
aglatmInterfaceTrafficEnforcementType5This identifies the ATM traffic enforcement type is 5.
For type 5 traffic enforcement, parameter 1
specifies CLP=0+1 peak traffic, parameter
2 specifies CLP=0 sustained rate, parameter 3
specifies CLP=0 maximum burst size, and parameter
4 specifies tagging (e.g., a value 1 may be
used to indicate tagging). Parameter
5 is not used.ro OBJECT IDENTIFIER .1.3.6.1.4.1.36.2.15.3.3.5.1.1.6 |
aglatmInterfaceTrafficEnforcementType6This identifies the ATM traffic enforcement type is 6.
For type 6 traffic enforcement, parameter 1
specifies CLP=0+1 peak traffic, parameter
2 specifies CLP=0+1 sustained rate, and parameter 3
specifies CLP=0+1 maximum burst size.
Parameters 4 and 5 are not used.ro OBJECT IDENTIFIER .1.3.6.1.4.1.36.2.15.3.3.5.1.1.7 |
aglatmInterfaceTrafficEnforcementType7This identifies the ATM traffic enforcement type is 7.
For type 7 traffic enforcement, parameter 1
specifies CLP=0+1 peak traffic and parameter
2 specifies best effort traffic
(e.g., a value 1 may be used to indicate
best effort traffic). Parameters 3, 4 and 5 are not used.ro OBJECT IDENTIFIER .1.3.6.1.4.1.36.2.15.3.3.5.1.1.8 |
aglatmInterfaceConfTableThis table contains ATM local interface configuration
parameters and state variables, one
entry per ATM interface port. SEQUENCE OF AglAtmInterfaceConfEntry .1.3.6.1.4.1.36.2.15.3.3.5.1.2 |
aglatmInterfaceConfEntryThis list contains ATM interface configuration
parameters and state variables. AglAtmInterfaceConfEntry .1.3.6.1.4.1.36.2.15.3.3.5.1.2.1 |
aglatmInterfaceIndexThe value of this object identifies the ATM port
interface for which this entry contains
management information. INTEGER .1.3.6.1.4.1.36.2.15.3.3.5.1.2.1.1 |
aglatmInterfaceMaxVpcsThe maximum number of VPCs supported at
this ATM interface.ro INTEGER .1.3.6.1.4.1.36.2.15.3.3.5.1.2.1.2 |
aglatmInterfaceMaxVccsThe maximum number of VCCs supported at
the ATM interface.ro INTEGER .1.3.6.1.4.1.36.2.15.3.3.5.1.2.1.3 |
aglatmInterfaceConfVpcsThe number of VPCs configured for use
at this ATM interface.ro INTEGER .1.3.6.1.4.1.36.2.15.3.3.5.1.2.1.4 |
aglatmInterfaceConfVccsThe number of VCCs configured for use
at the ATM interface.ro INTEGER .1.3.6.1.4.1.36.2.15.3.3.5.1.2.1.5 |
aglatmInterfaceMaxActiveVpiBitsThe maximum number of active VPI bits
configured for use at the ATM interface.ro INTEGER .1.3.6.1.4.1.36.2.15.3.3.5.1.2.1.6 |
aglatmInterfaceMaxActiveVciBitsThe maximum number of active VCI bits
configured for use at this ATM interface.ro INTEGER .1.3.6.1.4.1.36.2.15.3.3.5.1.2.1.7 |
aglatmInterfaceIlmiVpiVciThe decimal value of the three octet VPI/VCI
field that identifies the VCC supporting
the ILMI at the ATM interface.
If the value of this object is greater
than 16777215 then the ILMI is not supported
at the ATM interface.
The default VPI/VCI values for ILMI
are VPI=0 and VCI=16.ro INTEGER .1.3.6.1.4.1.36.2.15.3.3.5.1.2.1.8 |
aglatmInterfaceSpecificThis object points to the additional information
specific to ATM interfaces. For example, if
Enterprise specific objects have been defined
in addition to this MIB module, then the
value of this object refers to that MIB
defining these objects. If the additional
information is not present, then the value
should be {0 0}.ro OBJECT IDENTIFIER .1.3.6.1.4.1.36.2.15.3.3.5.1.2.1.9 |
aglatmInterfaceDs3PlcpTableThis table contains ATM interface DS3 PLCP
parameters and state variables, one entry per
ATM interface port. SEQUENCE OF AglAtmInterfaceDs3PlcpEntry .1.3.6.1.4.1.36.2.15.3.3.5.1.3 |
aglatmInterfaceDs3PlcpEntryThis list contains DS3 PLCP parameters and
state variables at the ATM interface. AglAtmInterfaceDs3PlcpEntry .1.3.6.1.4.1.36.2.15.3.3.5.1.3.1 |
aglatmInterfaceDs3PlcpIndexThe value of this object identifies the ATM
interface port for which this entry
contains management information and is the
same as the atmInterfaceIndex. INTEGER .1.3.6.1.4.1.36.2.15.3.3.5.1.3.1.1 |
aglatmInterfaceDs3PlcpSEFSsA DS3 Severely Errored Framing Second (SEFS)
is a count of one-second intervals
containing one or more SEF event.ro Counter .1.3.6.1.4.1.36.2.15.3.3.5.1.3.1.2 |
aglatmInterfaceDs3PlcpAlarmStateThis variable indicates if there is an
alarm present for the DS3 PLCP. The value
receivedFarEndAlarm means that the DS3 PLCP
has received an incoming Yellow
Signal, the value incomingLOF means that
the DS3 PLCP has declared a loss of frame (LOF)
failure condition, and the value noAlarm
means that there are no alarms present.ro Enumeration .1.3.6.1.4.1.36.2.15.3.3.5.1.3.1.3 |
aglatmInterfaceDs3PlcpUASsThe counter associated with the number of
Unavailable Seconds encountered by the PLCP.ro Counter .1.3.6.1.4.1.36.2.15.3.3.5.1.3.1.4 |
aglatmInterfaceSonetTCTableThis table contains ATM interface SONET TC
Sublayer parameters and state variables,
one entry per ATM interface port. SEQUENCE OF AglAtmInterfaceSonetTCEntry .1.3.6.1.4.1.36.2.15.3.3.5.1.4 |
aglatmInterfaceSonetTCEntryThis list contains SONET TC Sublayer parameters
and state variables at the ATM interface. AglAtmInterfaceSonetTCEntry .1.3.6.1.4.1.36.2.15.3.3.5.1.4.1 |
aglatmInterfaceSonetTCIndexThe value of this object identifies the ATM
interface port for which this entry
contains management information and is
the same as the atmInterfaceIndex. INTEGER .1.3.6.1.4.1.36.2.15.3.3.5.1.4.1.1 |
aglatmInterfaceSonetTCOCDEventsThe number of times the Out of Cell
Delineation (OCD) events occur. If seven
consecutive ATM cells have Header Error
Control (HEC) violations, an OCD event occurs.
A high number of OCD events may indicate a problem
with the SONET TC Sublayer.ro Counter .1.3.6.1.4.1.36.2.15.3.3.5.1.4.1.2 |
aglatmInterfaceSonetTCAlarmStateThis variable indicates if there is an
alarm present for the SONET TC Sublayer. The value
lcdFailure indicates that a Loss of
Cell Delineation (LCD) failure state has been
declared for the SONET TC Sublayer.ro Enumeration .1.3.6.1.4.1.36.2.15.3.3.5.1.4.1.3 |
aglsonetMIB OBJECT IDENTIFIER .1.3.6.1.4.1.36.2.15.3.3.6 |
aglsonetObjects OBJECT IDENTIFIER .1.3.6.1.4.1.36.2.15.3.3.6.1 |
aglsonetMedium OBJECT IDENTIFIER .1.3.6.1.4.1.36.2.15.3.3.6.1.1 |
aglsonetMediumTableThe SONET/SDH Medium table. SEQUENCE OF AglSonetMediumEntry .1.3.6.1.4.1.36.2.15.3.3.6.1.1.1 |
aglsonetMediumEntryAn entry in the SONET/SDH Medium table. AglSonetMediumEntry .1.3.6.1.4.1.36.2.15.3.3.6.1.1.1.1 |
aglsonetMediumIfIndexAn index value that uniquely identifies a SONET/SDH
Medium/Section/Line Interface. INTEGER .1.3.6.1.4.1.36.2.15.3.3.6.1.1.1.1.1 |
aglsonetMediumTypeThis variable identifies whether a SONET
or a SDH signal is used across this interface.ro Enumeration .1.3.6.1.4.1.36.2.15.3.3.6.1.1.1.1.2 |
aglsonetMediumTimeElapsedThe number of seconds, including partial
seconds, that have elapsed since the beginning of
the current error-measurement period.ro INTEGER .1.3.6.1.4.1.36.2.15.3.3.6.1.1.1.1.3 |
aglsonetMediumValidIntervalsThe number of previous intervals for which valid
data has been stored. A SONET device must support
at least n intervals.
The minimum value of n is 4.
The default of n is 32.
The maximum value of n is 96.
The value of this object will be n unless
the device was brought online within the last
(nx15) minutes, in which case the value will be the
number of complete 15 minute intervals the device has
been online.ro INTEGER .1.3.6.1.4.1.36.2.15.3.3.6.1.1.1.1.4 |
aglsonetMediumLineCodingThis variable describes the line coding for
this interface. The B3ZS and CMI are used for
electrical SONET/SDH signals (STS-1 and STS-3).
The Non-Return to Zero (NRZ) and the Return
to Zero are used for optical SONET/SDH signals.ro Enumeration .1.3.6.1.4.1.36.2.15.3.3.6.1.1.1.1.5 |
aglsonetMediumLineTypeThis variable describes the line type for
this interface. The line types are
Short and Long Range
Single Mode fiber or Multi-Mode fiber interfaces,
and coax and UTP for electrical interfaces. The
value sonetOther should be used when the Line Type is
not one of the listed values.ro Enumeration .1.3.6.1.4.1.36.2.15.3.3.6.1.1.1.1.6 |
aglsonetMediumCircuitIdentifierThis variable contains the transmission
vendor's circuit identifier, for the
purpose of facilitating troubleshooting.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.36.2.15.3.3.6.1.1.1.1.7 |
aglsonetSection OBJECT IDENTIFIER .1.3.6.1.4.1.36.2.15.3.3.6.1.2 |
aglsonetSectionCurrentTableThe SONET/SDH Section Current table. SEQUENCE OF AglSonetSectionCurrentEntry .1.3.6.1.4.1.36.2.15.3.3.6.1.2.1 |
aglsonetSectionCurrentEntryAn entry in the SONET/SDH Section Current table. AglSonetSectionCurrentEntry .1.3.6.1.4.1.36.2.15.3.3.6.1.2.1.1 |
aglsonetSectionCurrentIfIndexThe index value which uniquely identifies the
SONET/SDH Medium/Section/Line Interface. INTEGER .1.3.6.1.4.1.36.2.15.3.3.6.1.2.1.1.1 |
aglsonetSectionCurrentStatusThis variable indicates the
status of the interface.
The sonetSectionStatus
is a bit map represented
as a sum, therefore,
it can represent multiple defects
simultaneously.
The sonetSectionNoDefect should be
set if and only if
no other flag is set.
The various bit positions are:
1 sonetSectionNoDefect
2 sonetSectionLOS
4 sonetSectionLOFro INTEGER .1.3.6.1.4.1.36.2.15.3.3.6.1.2.1.1.2 |
aglsonetSectionCurrentESsThe counter associated with the number of Errored
Seconds encountered by a SONET/SDH
Section in the current 15 minute interval.ro Gauge .1.3.6.1.4.1.36.2.15.3.3.6.1.2.1.1.3 |
aglsonetSectionCurrentSESsThe counter associated with the number of
Severely Errored Seconds
encountered by a SONET/SDH Section in the current 15
minute interval.ro Gauge .1.3.6.1.4.1.36.2.15.3.3.6.1.2.1.1.4 |
aglsonetSectionCurrentSEFSsThe counter associated with the number of
Severely Errored Framing Seconds
encountered by a SONET/SDH Section in the current
15 minute interval.ro Gauge .1.3.6.1.4.1.36.2.15.3.3.6.1.2.1.1.5 |
aglsonetSectionCurrentCVsThe counter associated with the number of Coding
Violations encountered by a
SONET/SDH Section in the current 15 minute interval.ro Gauge .1.3.6.1.4.1.36.2.15.3.3.6.1.2.1.1.6 |
aglsonetLine OBJECT IDENTIFIER .1.3.6.1.4.1.36.2.15.3.3.6.1.3 |
aglsonetLineCurrentTableThe SONET/SDH Line Current table. SEQUENCE OF AglSonetLineCurrentEntry .1.3.6.1.4.1.36.2.15.3.3.6.1.3.1 |
aglsonetLineCurrentEntryAn entry in the SONET/SDH Line Current table. AglSonetLineCurrentEntry .1.3.6.1.4.1.36.2.15.3.3.6.1.3.1.1 |
aglsonetLineCurrentIfIndexThe index value which uniquely identifies the
SONET/SDH Medium/Line Interface. INTEGER .1.3.6.1.4.1.36.2.15.3.3.6.1.3.1.1.1 |
aglsonetLineCurrentStatusThis variable indicates the
status of the interface.
The sonetLineStatus
is a bit map represented
as a sum, therefore,
it can represent multiple defects
simultaneously.
The sonetLineNoDefect should be
set if and only if
no other flag is set.
The various bit positions are:
1 sonetLineNoDefect
2 sonetLineAIS
4 sonetLineRDIro INTEGER .1.3.6.1.4.1.36.2.15.3.3.6.1.3.1.1.2 |
aglsonetLineCurrentESsThe counter associated with the number of Errored
Seconds encountered by a SONET/SDH
Line in the current 15 minute interval.ro Gauge .1.3.6.1.4.1.36.2.15.3.3.6.1.3.1.1.3 |
aglsonetLineCurrentSESsThe counter associated with the number of
Severely Errored Seconds
encountered by a SONET/SDH Line in the current 15
minute
interval.ro Gauge .1.3.6.1.4.1.36.2.15.3.3.6.1.3.1.1.4 |
aglsonetLineCurrentCVsThe counter associated with the number of Coding
Violations encountered by a
SONET/SDH Line in the current 15 minute interval.ro Gauge .1.3.6.1.4.1.36.2.15.3.3.6.1.3.1.1.5 |
aglsonetLineCurrentUASsThe counter associated with the number of
Unavailable Seconds
encountered by a SONET/SDH Line in the current 15
minute
interval.ro Gauge .1.3.6.1.4.1.36.2.15.3.3.6.1.3.1.1.6 |
aglsonetObjectsPath OBJECT IDENTIFIER .1.3.6.1.4.1.36.2.15.3.3.6.2 |
aglsonetPath OBJECT IDENTIFIER .1.3.6.1.4.1.36.2.15.3.3.6.2.1 |
aglsonetPathCurrentTableThe SONET/SDH Path Current table. SEQUENCE OF AglSonetPathCurrentEntry .1.3.6.1.4.1.36.2.15.3.3.6.2.1.1 |
aglsonetPathCurrentEntryAn entry in the SONET/SDH Path Current table. AglSonetPathCurrentEntry .1.3.6.1.4.1.36.2.15.3.3.6.2.1.1.1 |
aglsonetPathCurrentIfIndexAn index value that uniquely identifies a SONET/SDH
Path Interface. INTEGER .1.3.6.1.4.1.36.2.15.3.3.6.2.1.1.1.1 |
aglsonetPathCurrentWidthA value that indicates the type of the SONET/SDH
Path. For SONET, the assigned types are
the STS-Nc SPEs, where N = 1, 3, 12, 24, and 48.
STS-1 is equal to 51.84 Mbps. For SDH, the assigned
types are the STM-Nc VCs, where N = 1, 4, and 16.rw Enumeration .1.3.6.1.4.1.36.2.15.3.3.6.2.1.1.1.2 |
aglsonetPathCurrentStatusThis variable indicates the
status of the interface.
The sonetPathStatus
is a bit map represented
as a sum, therefore,
it can represent multiple defects
simultaneously.
The sonetPathNoDefect should be
set if and only if
no other flag is set.
The various bit positions are:
1 sonetPathNoDefect
2 sonetPathSTSLOP
4 sonetPathSTSAIS
8 sonetPathSTSRDI
16 sonetPathUnequipped
32 sonetPathSignalLabelMismatchro INTEGER .1.3.6.1.4.1.36.2.15.3.3.6.2.1.1.1.3 |
aglsonetPathCurrentESsThe counter associated with the number of Errored
Seconds encountered by a SONET/SDH
Path in the current 15 minute interval.ro Gauge .1.3.6.1.4.1.36.2.15.3.3.6.2.1.1.1.4 |
aglsonetPathCurrentSESsThe counter associated with the number of
Severely Errored Seconds
encountered by a SONET/SDH Path in the current 15
minute interval.ro Gauge .1.3.6.1.4.1.36.2.15.3.3.6.2.1.1.1.5 |
aglsonetPathCurrentCVsThe counter associated with the number of Coding
Violations encountered by a
SONET/SDH Path in the current 15 minute interval.ro Gauge .1.3.6.1.4.1.36.2.15.3.3.6.2.1.1.1.6 |
aglsonetPathCurrentUASsThe counter associated with the number of
Unavailable Seconds
encountered by a Path in the current
15 minute, interval.ro Gauge .1.3.6.1.4.1.36.2.15.3.3.6.2.1.1.1.7 |
decMIBextension OBJECT IDENTIFIER .1.3.6.1.4.1.36.2.18 |
elanext OBJECT IDENTIFIER .1.3.6.1.4.1.36.2.18.1 |
efddi OBJECT IDENTIFIER .1.3.6.1.4.1.36.2.18.1.1 |
efddiSMT OBJECT IDENTIFIER .1.3.6.1.4.1.36.2.18.1.1.1 |
efddiSMTTableA list of SMT entries. The number of entries is given
by smtNumber, defined in the FDDI MIB. SEQUENCE OF EfddiSMTEntry .1.3.6.1.4.1.36.2.18.1.1.1.1 |
efddiSMTEntryA collection of objects containing information for a
given SMT link. EfddiSMTEntry .1.3.6.1.4.1.36.2.18.1.1.1.1.1 |
eSMTIndexIdentifies the SMT Index. The value of this object is
the same as the snmpFddiSMTIndex, defined in the FDDI MIB,
for this smt entity.ro INTEGER .1.3.6.1.4.1.36.2.18.1.1.1.1.1.1 |
eSMTStationTypeThe Station Type Identification.ro Enumeration .1.3.6.1.4.1.36.2.18.1.1.1.1.1.2 |
eSMTTracesReceivedThe number of PC Traces received by this station.ro Counter .1.3.6.1.4.1.36.2.18.1.1.1.1.1.3 |
efddiMAC OBJECT IDENTIFIER .1.3.6.1.4.1.36.2.18.1.1.2 |
efddiMACTableA list of MAC entries. The number of entries is given
by macNumber, defined in the FDDI MIB. SEQUENCE OF EfddiMACEntry .1.3.6.1.4.1.36.2.18.1.1.2.1 |
efddiMACEntryA collection of objects containing information for a
given MAC entity. EfddiMACEntry .1.3.6.1.4.1.36.2.18.1.1.2.1.1 |
eMACSMTIndexThe value of the SMT index associated with this MAC.
The value of this object is the same as the
snmpFddiMACSMTIndex, defined in the FDDI MIB, for this
MAC entity.ro INTEGER .1.3.6.1.4.1.36.2.18.1.1.2.1.1.1 |
eMACIndexIdentifies the MAC Index. The value of this object is
the same as the snmpFddiMACIndex, defined in the FDDI MIB,
for this MAC entity.ro INTEGER .1.3.6.1.4.1.36.2.18.1.1.2.1.1.2 |
eMACLinkIndexThe SMT Resource Index.ro INTEGER .1.3.6.1.4.1.36.2.18.1.1.2.1.1.3 |
eMACLinkStateThe current state of the link.ro Enumeration .1.3.6.1.4.1.36.2.18.1.1.2.1.1.4 |
eMACRingPurgerStateThe current Ring Purger state.ro Enumeration .1.3.6.1.4.1.36.2.18.1.1.2.1.1.5 |
eMACRingPurgerEnableIf true, this Link will participate in the Ring Purger
Election and, if elected, perform the Ring Purger function.rw Enumeration .1.3.6.1.4.1.36.2.18.1.1.2.1.1.6 |
eMACRingPurgeErrorsThe number of times the MAC PurgeError Event bit was set.ro Counter .1.3.6.1.4.1.36.2.18.1.1.2.1.1.7 |
eMACFrameStripModeMethod of frame removal used by this station.ro Enumeration .1.3.6.1.4.1.36.2.18.1.1.2.1.1.8 |
eMACFCIStripErrorsThe number of times a Frame Content Independent Strip
operation was terminated by receipt of a token.ro Counter .1.3.6.1.4.1.36.2.18.1.1.2.1.1.9 |
eMACRingErrorReasonReason for last ring disturbance.ro Enumeration .1.3.6.1.4.1.36.2.18.1.1.2.1.1.10 |
eMACRingInitializationsInitiatedNumber of Ring Claim Processes initiated by this link
entity.ro Counter .1.3.6.1.4.1.36.2.18.1.1.2.1.1.11 |
eMACRingInitializationsReceivedNumber of Ring Claim Processes or Ring Beaconing Processes
initiated by a remote link entity and detected by this link
entity.ro Counter .1.3.6.1.4.1.36.2.18.1.1.2.1.1.12 |
eMACRingBeaconingInitiatedThe number of Ring Beacon Processes initiated by this
link entity.ro Counter .1.3.6.1.4.1.36.2.18.1.1.2.1.1.13 |
eMACDuplicateAddressTestFailuresThe number of times the duplicate address test failed.ro Counter .1.3.6.1.4.1.36.2.18.1.1.2.1.1.14 |
eMACDuplicateTokensDetectedThe number of times this link entity detected a duplicate
token.ro Counter .1.3.6.1.4.1.36.2.18.1.1.2.1.1.15 |
eMACUpstreamNbrDuplAddressFlagThe upstream neighbor's duplicate address status, as
reported by the NIF frame. Unknown if no NIF frame has
been received yet.ro Enumeration .1.3.6.1.4.1.36.2.18.1.1.2.1.1.16 |
eMACTracesInitiatedThe number of PC Traces initiated by this station.ro Counter .1.3.6.1.4.1.36.2.18.1.1.2.1.1.17 |
eMACRestrictedTokenTimeoutThe restricted token timeout, which limits how long a
single restricted mode dialog may last before being
terminated.rw INTEGER .1.3.6.1.4.1.36.2.18.1.1.2.1.1.18 |
eMACFrameStatusErrorsThe number of frames received on the line that had the
E (error detected) indicator set or a missing E indicator.ro Counter .1.3.6.1.4.1.36.2.18.1.1.2.1.1.19 |
eMACFrameAlignmentErrorsThe number of frames received on the line that contained
an odd number of symbols; that is, a non-integral number
of octets.ro Counter .1.3.6.1.4.1.36.2.18.1.1.2.1.1.20 |
eMACTransmitUnderrunsThe number of times an underrun occured because the
device's transmit FIFO became empty due to insufficient
memory. In other words, the device was trying to
transmit but could not get into memory fast enough.ro Counter .1.3.6.1.4.1.36.2.18.1.1.2.1.1.21 |
efddiPORT OBJECT IDENTIFIER .1.3.6.1.4.1.36.2.18.1.1.3 |
efddiPORTTableA list of PORT entries. The number of entries is given
by portNumber, defined in the FDDI MIB. SEQUENCE OF EfddiPORTEntry .1.3.6.1.4.1.36.2.18.1.1.3.1 |
efddiPORTEntryA collection of objects containing information for a
given PORT entity. EfddiPORTEntry .1.3.6.1.4.1.36.2.18.1.1.3.1.1 |
ePORTSMTIndexThe value of the SMT index associated with this port.
The value of this object is the same as the
snmpFddiPORTSMTIndex, defined in the FDDI MIB, for
this PORT entity.ro INTEGER .1.3.6.1.4.1.36.2.18.1.1.3.1.1.1 |
ePORTIndexIdentifies the PORT Index. The value of this object is
the same as the snmpFddiPORTIndex, defined in the FDDI MIB,
for this PORT entity.ro INTEGER .1.3.6.1.4.1.36.2.18.1.1.3.1.1.2 |
ePORTPHYIndexThe SMT Resource index. Index of the PHY resource
used to identify the PHY PORT in ANSI SMT frames.ro INTEGER .1.3.6.1.4.1.36.2.18.1.1.3.1.1.3 |
ePORTPMDTypeThe physical media type of the PORT.ro Enumeration .1.3.6.1.4.1.36.2.18.1.1.3.1.1.4 |
ePORTPHYStateThe PHY state.ro Enumeration .1.3.6.1.4.1.36.2.18.1.1.3.1.1.5 |
ePORTRejectReasonThe current reject reason.ro Enumeration .1.3.6.1.4.1.36.2.18.1.1.3.1.1.6 |
ePORTConnectionsCompletedThe number of Physical Connections established for this
PHY PORT.ro Counter .1.3.6.1.4.1.36.2.18.1.1.3.1.1.7 |
ePORTTNEExpRejectsThe number of times a physical disconnection took place
because the TNE Noise Timer expired.ro Counter .1.3.6.1.4.1.36.2.18.1.1.3.1.1.8 |
ePORTElasticityBufferErrorsThe number of ELM Chip EBUFF_ERROR events.ro Counter .1.3.6.1.4.1.36.2.18.1.1.3.1.1.9 |
efddiFDX OBJECT IDENTIFIER .1.3.6.1.4.1.36.2.18.1.1.4 |
efddiFDXTableA list of FDX entries. SEQUENCE OF EfddiFDXEntry .1.3.6.1.4.1.36.2.18.1.1.4.1 |
efddiFDXEntryA collection of objects containing information for a
given FDX MAC entity. EfddiFDXEntry .1.3.6.1.4.1.36.2.18.1.1.4.1.1 |
eFDXSMTIndexThe value of the SMT index associated with this FDX MAC.ro INTEGER .1.3.6.1.4.1.36.2.18.1.1.4.1.1.1 |
eFDXMACIndexThe value of the MAC index associated with this FDX MAC.ro INTEGER .1.3.6.1.4.1.36.2.18.1.1.4.1.1.2 |
eFDXEnableWhen true, this link will participate in the full duplex
auto-configuration and, if this is successful, will
operate in the full duplex mode.rw Enumeration .1.3.6.1.4.1.36.2.18.1.1.4.1.1.3 |
eFDXOpWhen true, this link is operating in the full duplex mode.ro Enumeration .1.3.6.1.4.1.36.2.18.1.1.4.1.1.4 |
eFDXStateThe state of the full duplex Control process.ro Enumeration .1.3.6.1.4.1.36.2.18.1.1.4.1.1.5 |
esystem OBJECT IDENTIFIER .1.3.6.1.4.1.36.2.18.1.2 |
esysChar OBJECT IDENTIFIER .1.3.6.1.4.1.36.2.18.1.2.1 |
esysRomVersionThe version number of the software stored in ROM.ro INTEGER .1.3.6.1.4.1.36.2.18.1.2.1.1 |
esysInitSwitchThis object allows the management action of initializing
a device and forcing it to run selftest. It can also be
used to reset all information added to the device's NVRAM.
When read, it returns a value of other(1).rw Enumeration .1.3.6.1.4.1.36.2.18.1.2.1.2 |
esysResetDefaultsSwitchThis object is the state of a hardware switch which,
when true, causes the device to reset its parameters
to the factory defaults when initialized.ro Enumeration .1.3.6.1.4.1.36.2.18.1.2.1.3 |
esysGatewayAddressThis object allows the setting of a default gateway
address for this device.rw IpAddress .1.3.6.1.4.1.36.2.18.1.2.1.4 |
esysTrapAddressTableA table of IP Addresses to which this device will send
traps. SEQUENCE OF EsysTrapEntry .1.3.6.1.4.1.36.2.18.1.2.1.5 |
esysTrapEntryEach entry contains an IP Address to which all SNMP Traps
will be sent by this device. EsysTrapEntry .1.3.6.1.4.1.36.2.18.1.2.1.5.1 |
esysTrapAddressAn IP Address to which all SNMP traps generated by this
device will be sent.rw IpAddress .1.3.6.1.4.1.36.2.18.1.2.1.5.1.1 |
esysUpdateSwitchA software switch that, when set to true, instructs the
device to accept a down-line loaded firmware upgrade.
If false, the device will not accept upgrades.rw Enumeration .1.3.6.1.4.1.36.2.18.1.2.1.6 |
esysLastLoadHostThe physical address of the last host, if any, that
responded to the device's request for a downline load
of software.ro OCTET STRING .1.3.6.1.4.1.36.2.18.1.2.1.7 |
esysStatus OBJECT IDENTIFIER .1.3.6.1.4.1.36.2.18.1.2.2 |
esysDeviceStateThe operational state of the device.ro Enumeration .1.3.6.1.4.1.36.2.18.1.2.2.1 |
esysDeviceBrokenReasonThe reason that the Device State is BROKEN. If current
state is not BROKEN and the Unsolicited Resets counter is
nonzero, this object show reason for last failure.ro Enumeration .1.3.6.1.4.1.36.2.18.1.2.2.2 |
esysNvramFailedA flag, that, when set to True, indicates that the
NVRAM failed selftest following the last initialization
of the device.ro Enumeration .1.3.6.1.4.1.36.2.18.1.2.2.3 |
esysCounters OBJECT IDENTIFIER .1.3.6.1.4.1.36.2.18.1.2.3 |
esysPowerupsThe number of times this device was powered on.
Power Ups, Management Resets and Unsolicited Resets
are all mutually exclusive.ro Counter .1.3.6.1.4.1.36.2.18.1.2.3.1 |
esysMgmtResetsNumber of times the device was initialized with a
management command using esysInitSwitch. Power Ups,
Management Resets and Unsolicited Resets are all mutually
exclusive.ro Counter .1.3.6.1.4.1.36.2.18.1.2.3.2 |
esysUnsolicitedResetsNumber of times the device initialized itself after
encountering a fatal error. Power Ups, Management Resets
and Unsolicited Resets are all mutually exclusive.ro Counter .1.3.6.1.4.1.36.2.18.1.2.3.3 |
esysConcConfig OBJECT IDENTIFIER .1.3.6.1.4.1.36.2.18.1.2.4 |
esysFRUConfigTableA list of configuration table entries. SEQUENCE OF EsysFRUConfigEntry .1.3.6.1.4.1.36.2.18.1.2.4.1 |
esysFRUConfigEntryA collection of objects containing information for a
given configuration entry. EsysFRUConfigEntry .1.3.6.1.4.1.36.2.18.1.2.4.1.1 |
esysFRUIndexThis object is used for indexing the FRU configuration
table.ro INTEGER .1.3.6.1.4.1.36.2.18.1.2.4.1.1.1 |
esysFRUSlotThe physical slot number in which the module resides, if
applicable. If not applicable, this is reported as '0'.ro INTEGER .1.3.6.1.4.1.36.2.18.1.2.4.1.1.2 |
esysFRUDescA textual description of this FRU.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.36.2.18.1.2.4.1.1.3 |
esysFRUTypeInteger representation for the FRU type. This is the
machine-readable form of the descriptor object.ro Enumeration .1.3.6.1.4.1.36.2.18.1.2.4.1.1.4 |
esysFRURevThis object represents the FRU revision number.ro INTEGER .1.3.6.1.4.1.36.2.18.1.2.4.1.1.5 |
esysFRUStateThe operational state of the FRU, if present.ro Enumeration .1.3.6.1.4.1.36.2.18.1.2.4.1.1.6 |
esysFddiPortTrapSwitchThis is a switch to enable or diable FDDI port up and port
down traps. When set to true, the concentrator will
send a trap when one of its ports comes up or goes down.rw Enumeration .1.3.6.1.4.1.36.2.18.1.2.4.2 |
einterfaces OBJECT IDENTIFIER .1.3.6.1.4.1.36.2.18.1.3 |
eifTableA list of interface entries. The number of entries is
given by ifNumber, defined in MIB-II. SEQUENCE OF EifEntry .1.3.6.1.4.1.36.2.18.1.3.1 |
eifEntryA collection of objects containing information for a
given interface. EifEntry .1.3.6.1.4.1.36.2.18.1.3.1.1 |
eifIndexIdentifies the Interface. The value of this object is
the same as the ifIndex, defined in MIB-II, for this
interface.ro INTEGER .1.3.6.1.4.1.36.2.18.1.3.1.1.1 |
eifBadFramesReceivedNumber of frames received with a bad frame check sequence.ro Counter .1.3.6.1.4.1.36.2.18.1.3.1.1.2 |
eifReceiveOverrunNumber of times that the device received a frame loss
indication from the hardware on the interface.ro Counter .1.3.6.1.4.1.36.2.18.1.3.1.1.3 |
eifOversizeFramesNumber of frames received on the interface that were
larger than the maximum legal size.ro Counter .1.3.6.1.4.1.36.2.18.1.3.1.1.4 |
eifTransmitFramesErrorNumber of frames that were transmitted with an error
on the line.ro Counter .1.3.6.1.4.1.36.2.18.1.3.1.1.5 |
eifMgmtSetsAllowedSwitchThis hardware switch, when true, allows write
access to the device. This object has meaning only
when the corresponding functionality is present.ro Enumeration .1.3.6.1.4.1.36.2.18.1.3.1.1.6 |
ebridge OBJECT IDENTIFIER .1.3.6.1.4.1.36.2.18.1.4 |
ebrChar OBJECT IDENTIFIER .1.3.6.1.4.1.36.2.18.1.4.1 |
ebrLB100SpanningTreeVerThe version number of the Spanning Tree algorithm
used by the bridge when in the LAN Bridge 100 Spanning
Tree mode.ro INTEGER .1.3.6.1.4.1.36.2.18.1.4.1.1 |
ebr802SpanningTreeVerThe version number of the Spanning Tree algorithm
used by the bridge when in the 802.1d Spanning Tree mode.ro INTEGER .1.3.6.1.4.1.36.2.18.1.4.1.2 |
ebrMaxForwardingDBEntriesThe maximum number of address entries that the bridge
can store in its volatile memory.ro INTEGER .1.3.6.1.4.1.36.2.18.1.4.1.3 |
ebrMaxNVForwardingDBEntriesThe maximum number of permanent address entries that
the bridge canstore in its NVRAM.ro INTEGER .1.3.6.1.4.1.36.2.18.1.4.1.4 |
ebrMaxProtocolDBEntriesThe maximum number of protocol entries that the bridge
can store in its protocol database. These entries control
the handling of frames based on their Ethernet PT,
IEEE 802.2 DSAP or IEEE 802 SNAP Protocol ID.ro INTEGER .1.3.6.1.4.1.36.2.18.1.4.1.5 |
ebrMaxNVProtocolDBEntriesThe maximum number of protocol entries that the bridge
can store in its nonvolatile memory. These are retained
after a power-down.ro INTEGER .1.3.6.1.4.1.36.2.18.1.4.1.6 |
ebrForwardingDBPurgeThresholdThe total number of active and inactive address entries
that will trigger a purge of the inactive entries.ro INTEGER .1.3.6.1.4.1.36.2.18.1.4.1.7 |
ebrPortTestPassedThresholdThe number of consecutive successful self-tests needed
before the bridge considers a line to be operational.rw INTEGER .1.3.6.1.4.1.36.2.18.1.4.1.8 |
ebrPortTestIntervalThe interval, in seconds, at which the bridge will run
selftests on a line that is in the BROKEN state.rw INTEGER .1.3.6.1.4.1.36.2.18.1.4.1.9 |
ebrTopologyChangeTimerThe number of seconds remaining, if this is the Root,
for which Topology Change will be propagated in Hello
messages. Otherwise this value will be reported as 0.ro INTEGER .1.3.6.1.4.1.36.2.18.1.4.1.10 |
ebrManualFilterSwitchA switch that controls address filtering. When true,
the bridge purges the learned entries from its forwarding
database, stops its learning process, and forwards only
frames with destination and source addresses that have
been specified via management.rw Enumeration .1.3.6.1.4.1.36.2.18.1.4.1.11 |
ebrFragmentationSwitchA switch that controls whether fragmentation is performed
by the bridge when a large IP frame is received on a datalink
that supports a higer frame size than the other datalink.rw Enumeration .1.3.6.1.4.1.36.2.18.1.4.1.12 |
ebrRemoveMgmtAddressThis object allows the action of removing all management
entered addresses from the forwarding database when
set to true(2). When read, it returns a value of other(1).rw Enumeration .1.3.6.1.4.1.36.2.18.1.4.1.13 |
ebrRemoveMgmtProtoThis object allows the action of removing all management
entered protocols from the protocol database when set
to true(2). When read, it returns a value of other(1).rw Enumeration .1.3.6.1.4.1.36.2.18.1.4.1.14 |
ebrStat OBJECT IDENTIFIER .1.3.6.1.4.1.36.2.18.1.4.2 |
ebrCurrForwardingDBEntriesThe number of address entries in the bridge's volatile
memory. These will be lost upon loss of power.ro INTEGER .1.3.6.1.4.1.36.2.18.1.4.2.1 |
ebrCurrNVForwardingDBEntriesThe number of address entries in the bridge's NVRAM.
These will be retained after loss of power.ro INTEGER .1.3.6.1.4.1.36.2.18.1.4.2.2 |
ebrCurrProtocolDBEntriesThe number of protocol entries that are stored in the
bridge's protocol database. These control the handling
of frames based on their Ethernet protocol type, IEEE
802.2 DSAP, or 802 SNAP Protocol ID.ro INTEGER .1.3.6.1.4.1.36.2.18.1.4.2.3 |
ebrCurrNVProtocolDBEntriesThe number of protocol entries in the bridge's NVRAM.
These are retained after a power loss.ro INTEGER .1.3.6.1.4.1.36.2.18.1.4.2.4 |
ebrMgmtHeardPortThe port on which this command was received.ro INTEGER .1.3.6.1.4.1.36.2.18.1.4.2.5 |
ebrLB100BeingPolledThe address of the LAN Bridge 100 mode bridge that sent
this bridge into the LAN Bridge 100 Spanning Tree mode.
If this bridge is the Root, this object indicates the
bridge that will be polled periodically to determine
if it is still necessary to stay in this Spanning Tree
mode.ro OCTET STRING .1.3.6.1.4.1.36.2.18.1.4.2.6 |
ebrInactiveForwardingDBEntriesThe number of inactive address entries in the bridge's
forwarding database. The bridge marks an address entry
inactive when the entry is aged out.ro INTEGER .1.3.6.1.4.1.36.2.18.1.4.2.7 |
ebrTimeSinceForwardingDBPurgedThe number of seconds since the bridge cleared the
forwarding database of inactive entries.ro INTEGER .1.3.6.1.4.1.36.2.18.1.4.2.8 |
ebrTimeSinceLastHelloThe number of seconds since the bridge last sent a
Hello message.ro INTEGER .1.3.6.1.4.1.36.2.18.1.4.2.9 |
ebrCoun OBJECT IDENTIFIER .1.3.6.1.4.1.36.2.18.1.4.3 |
ebrDeviceFramesLostThe number of frames addressed to the bridge itself that
the bridge discarded because it did not have sufficient
receive buffers available.ro Counter .1.3.6.1.4.1.36.2.18.1.4.3.1 |
ebrSpanningTreeModeChangesThe number of times that the bridge switched from the
802.1d Spanning Tree mode to the LB100 Spanning Tree mode.ro Counter .1.3.6.1.4.1.36.2.18.1.4.3.2 |
ebrSpan OBJECT IDENTIFIER .1.3.6.1.4.1.36.2.18.1.4.4 |
ebrBestRootAgeThe age, in hundereths of seconds, of the Hello message
that established the best root.ro INTEGER .1.3.6.1.4.1.36.2.18.1.4.4.1 |
ebrTopologyChangeFlagA flag that indicates whether a Topology Change is
currently in effect on the extended LAN.ro Enumeration .1.3.6.1.4.1.36.2.18.1.4.4.2 |
ebrTellParentFlagA flag that indicates if the bridge is attempting to
propagate a topology change towards the Root.ro Enumeration .1.3.6.1.4.1.36.2.18.1.4.4.3 |
ebrForwardingDBShortAgingTimeThe number of seconds that the bridge keeps learned
entries active while a topology change is in effect.rw INTEGER .1.3.6.1.4.1.36.2.18.1.4.4.4 |
ebrBadHelloLimitThe number of hello intervals during which the bridge
receives one or more bad hellos on a line, before the
bridge performs a test on the link. A bad Hello message
is one that contains inferior information that is received
on a port on which this bridge is Designated.rw INTEGER .1.3.6.1.4.1.36.2.18.1.4.4.5 |
ebrBadHelloResetTimerThe number of Hello intervals without bad Hellos that
the bridge will wait before it resets its bad Hello
count to zero.rw INTEGER .1.3.6.1.4.1.36.2.18.1.4.4.6 |
ebrNoFrameIntervalThe The number of seconds of inactivity on a line that
will cause the bridge to run a test on that line. The
bridge considers a line to be inactive if it does not
receive any frames on that line.rw INTEGER .1.3.6.1.4.1.36.2.18.1.4.4.7 |
ebrLB100PollTimeThe number of seconds that a Root bridge in LAN Bridge 100
mode waits between polling the LAN Bridge 100 that is
keeping it in this mode. This polling is done to determine
whether the LB100 is still present on the extended LAN.rw INTEGER .1.3.6.1.4.1.36.2.18.1.4.4.8 |
ebrLB100ResponseTimeoutThe number of seconds that a Root in LAN Bridge 100
Spanning Tree mode will wait for a response from the
LAN Bridge 100 which is keeping it in this mode, before
which it will assume that the LB100 is no longer on
the extended LAN.rw INTEGER .1.3.6.1.4.1.36.2.18.1.4.4.9 |
ebrLB100SpanningTreeCompatA switch that controls the Spanning Tree mode used by
the bridge. If in Auto-Select mode, the bridge will
go into 802 Spanning Tree mode by default, but will switch
to LB100 mode as soon as a LB100 is detected. In 802
Spanning Tree mode, the bridge will stay in 802 mode.rw Enumeration .1.3.6.1.4.1.36.2.18.1.4.4.10 |
ebrInterfaces OBJECT IDENTIFIER .1.3.6.1.4.1.36.2.18.1.4.5 |
ebrIfTableA list of interface entries. The number of entries is
given by ifNumber, defined in MIB-II. SEQUENCE OF EbrIfEntry .1.3.6.1.4.1.36.2.18.1.4.5.1 |
ebrIfEntryA collection of objects containing information for a
given interface. EbrIfEntry .1.3.6.1.4.1.36.2.18.1.4.5.1.1 |
ebrIfIndexIdentifies the Interface. The value of this object is
the same as the ifIndex, defined in MIB-II, for this
interface.ro INTEGER .1.3.6.1.4.1.36.2.18.1.4.5.1.1.1 |
ebrIfLinkBrokenReasonThe reason why the link was last broken. A possible
internal fault(1) indicates a problem with the bridge
line itself, a possible external fault(2), indicates
a problem with the transmission medium to which the
line is attached.ro Enumeration .1.3.6.1.4.1.36.2.18.1.4.5.1.1.2 |
ebrIfPortRestartsThe number of times the bridge restarted the line.ro Counter .1.3.6.1.4.1.36.2.18.1.4.5.1.1.3 |
ebrIfUnknownDAReceivedThe number of frames received on this line for which the
bridge had no address entry in its forwarding database.ro Counter .1.3.6.1.4.1.36.2.18.1.4.5.1.1.4 |
ebrIfFramesAddrFilteredThe number of frames filtered by the bridge on this
port because of address entries in the forwarding database.ro Counter .1.3.6.1.4.1.36.2.18.1.4.5.1.1.5 |
ebrIfMultiFramesFilteredThe number of frames with multicast destination addresses
that were received on the line on the line and filtered
by the bridge.ro Counter .1.3.6.1.4.1.36.2.18.1.4.5.1.1.6 |
ebrIfFramesProtocolFilteredThe number of frames received on this line that the
bridge discarded because of entries set by management
in the protocol database.ro Counter .1.3.6.1.4.1.36.2.18.1.4.5.1.1.7 |
ebrIfDeviceFramesSentThe number of frames originating from the bridge itself
that were transmitted on this line.ro Counter .1.3.6.1.4.1.36.2.18.1.4.5.1.1.8 |
ebrIfDeviceFramesReceivedThe number of frames addressed to the bridge itself
that were received on this line.ro Counter .1.3.6.1.4.1.36.2.18.1.4.5.1.1.9 |
ebrIfDeviceBytesSentThe number of bytes in the frames originating from the
bridge that were transmitted on this line.ro Counter .1.3.6.1.4.1.36.2.18.1.4.5.1.1.10 |
ebrIfDeviceBytesReceivedThe number of bytes in the frames addressed to the bridge
itself that were received on this line.ro Counter .1.3.6.1.4.1.36.2.18.1.4.5.1.1.11 |
ebrIfDeviceFramesLostThe number of frames received on the line addressed
to the bridge itself discarded by the bridge because it
did not have internal buffers to store them.ro Counter .1.3.6.1.4.1.36.2.18.1.4.5.1.1.12 |
ebrIfMultiBytesSentThe number of bytes in Multicast Frames sent, as reported
in ifOutNUcastPkts, defined in MIB-II.ro Counter .1.3.6.1.4.1.36.2.18.1.4.5.1.1.13 |
ebrIfMultiBytesReceivedThe number of bytes in Multicast Frames received, as
reported in ifInNUcastPkts, defined in MIB-II.ro Counter .1.3.6.1.4.1.36.2.18.1.4.5.1.1.14 |
ebrIfMultiDeviceFramesSentThe number of frames with multicast destination addresses
transmitted by the bridge itself on the line.ro Counter .1.3.6.1.4.1.36.2.18.1.4.5.1.1.15 |
ebrIfMultiDeviceFramesReceivedThe number of frames with multicast destination addresses
received by the bridge itslef on the line.ro Counter .1.3.6.1.4.1.36.2.18.1.4.5.1.1.16 |
ebrIfMultiDeviceBytesSentThe number of bytes in ebrIfMultiDeviceFramesSent.ro Counter .1.3.6.1.4.1.36.2.18.1.4.5.1.1.17 |
ebrIfMultiDeviceBytesReceivedThe number of bytes in ebrIfMultiDeviceFramesReceived.ro Counter .1.3.6.1.4.1.36.2.18.1.4.5.1.1.18 |
ebrIfBadBytesReceivedThe number of bytes in frames received that had a bad
frame check sequence.ro Counter .1.3.6.1.4.1.36.2.18.1.4.5.1.1.19 |
ebrIfBadHelloLimitExceededThe number of times that the Bad Hellos on the line
exceeded the Bad Hello limit.ro Counter .1.3.6.1.4.1.36.2.18.1.4.5.1.1.20 |
ebrIfEtherTableA list of interface entries for an Ethernet port. SEQUENCE OF EbrIfEtherEntry .1.3.6.1.4.1.36.2.18.1.4.5.2 |
ebrIfEtherEntryA collection of objects containing information for a
given interface. EbrIfEtherEntry .1.3.6.1.4.1.36.2.18.1.4.5.2.1 |
ebrIfEthIndexIdentifies the Interface. The value of this object is
the same as the ifIndex, defined in MIB-II, for this
interface.ro INTEGER .1.3.6.1.4.1.36.2.18.1.4.5.2.1.1 |
ebrIfEthPhysicalMediumTypeThe type of physical medium to which this line is
attached.ro Enumeration .1.3.6.1.4.1.36.2.18.1.4.5.2.1.2 |
ebrIfEthCollisionPresenceTestSwitchA switch that informs the bridge whether the transceiver
on this line is using the Collision Presence Test (CPT),
commonly known as heartbeat. It must be enabled if
the line's transceiver has CPT.rw Enumeration .1.3.6.1.4.1.36.2.18.1.4.5.2.1.3 |
ebrIfEthCollisionTestFailedThe number of times that a Collision Presence Test (CPT)
signal was not detected within 4 microseconds after a
transmission on the line. This counter is valid only
if ebrIfEthCollisionPresenceTestSwitch is set to true
for this line.ro Counter .1.3.6.1.4.1.36.2.18.1.4.5.2.1.4 |
ebrIfEthFramingErrorThe number of times that a frame received on the line
contained both a noninteger multiple of 8 bits and
a CRC error.ro Counter .1.3.6.1.4.1.36.2.18.1.4.5.2.1.5 |
ebrIfEthLengthErrorThe number of 802.3 frames received that contained a
Length field inconsistent with the actual number of
data bytes in the packet.ro Counter .1.3.6.1.4.1.36.2.18.1.4.5.2.1.6 |
ebrIfEthTransmitMultipleCollisionsThe number of times that the bridge had to retry
transmission of a frame on the line. This was
because of collisions during transmission due to
congestion on the physical medium.ro Counter .1.3.6.1.4.1.36.2.18.1.4.5.2.1.7 |
ebrIfEthCarrierLossThe number of times that the bridge detected a loss of
the carrier signal while transmitting a frame on the
line.ro Counter .1.3.6.1.4.1.36.2.18.1.4.5.2.1.8 |
ebrIfEthCollisionLimitExceededThe number of times that the bridge failed to transmit
a frame on this line after 16 attempts, the collision
limit.ro Counter .1.3.6.1.4.1.36.2.18.1.4.5.2.1.9 |
ebrIfFddiTableA list of interface entries for an FDDI port. SEQUENCE OF EbrIfFddiEntry .1.3.6.1.4.1.36.2.18.1.4.5.3 |
ebrIfFddiEntryA collection of objects containing information for a
given interface. EbrIfFddiEntry .1.3.6.1.4.1.36.2.18.1.4.5.3.1 |
ebrIfFddiIndexIdentifies the Interface. The value of this object is
the same as the ifIndex, defined in MIB-II, for this
interface.ro INTEGER .1.3.6.1.4.1.36.2.18.1.4.5.3.1.1 |
ebrIfFddiUnprocessedErrorPacketsThe number of times that an error frame was received
on thisline but the bridge did not have time to
decipher it.ro Counter .1.3.6.1.4.1.36.2.18.1.4.5.3.1.2 |
ebrIfFddiIpDatagramsFragmentedThe number or large IP Datagrams that were fragmented
into smaller frames because they did not fit into
legal size packets on the smaller datalink after
translation.ro Counter .1.3.6.1.4.1.36.2.18.1.4.5.3.1.3 |
ebrIfFddiIpDontFragmentThe number of large IP datagrams that could not be
fragmented because the DONT-FRAGMENT bit was set in
the IP header.ro Counter .1.3.6.1.4.1.36.2.18.1.4.5.3.1.4 |
ebrIfFddiIpIllegalHeaderLengthThe number of large IP datagrams that were discarded
instead of being fragmented because the IP header was
of illegal length.ro Counter .1.3.6.1.4.1.36.2.18.1.4.5.3.1.5 |
ebrIfFddiIpIllegalSizeThe number of large IP datagrams that were discarded
instead of being fragmented because the IP header
indicated a length greater than the number of actual
bytes in the received datagram.ro Counter .1.3.6.1.4.1.36.2.18.1.4.5.3.1.6 |
ebrIfSpanTableA list of interface entries for an FDDI port. SEQUENCE OF EbrIfSpanEntry .1.3.6.1.4.1.36.2.18.1.4.5.4 |
ebrIfSpanEntryA collection of objects containing information for a
given interface. EbrIfSpanEntry .1.3.6.1.4.1.36.2.18.1.4.5.4.1 |
ebrIfSpIndexIdentifies the Interface. The value of this object is
the same as the ifIndex, defined in MIB-II, for this
interface.ro INTEGER .1.3.6.1.4.1.36.2.18.1.4.5.4.1.1 |
ebrIfSpDesigRootAgeThe age, in hundreths of seconds, of the last Hello
message received from the designated bridge on the line.ro INTEGER .1.3.6.1.4.1.36.2.18.1.4.5.4.1.2 |
ebrIfSpForwardDelayTimerThe time remaining, in hundreths of seconds, before the
bridge will leave the Preforwarding state (listening or
learning), and enter the Forwarding State. If not in
preforwarding, this value will be reported as 0.ro INTEGER .1.3.6.1.4.1.36.2.18.1.4.5.4.1.3 |
ebrIfSpBadHelloCountThe number of Hello intervals during which at least one
Bad Hello was received.ro Counter .1.3.6.1.4.1.36.2.18.1.4.5.4.1.4 |
ebrIfSpPossibleLoopFlagA flag that indicates whether the bridge detected a loop
condition on this line.ro Enumeration .1.3.6.1.4.1.36.2.18.1.4.5.4.1.5 |
ebrIfSpTopologyChangeAckFlagA flag that indicates whether a topology change
notification received on a link that we are designated
on needs to be acknowledged.ro Enumeration .1.3.6.1.4.1.36.2.18.1.4.5.4.1.6 |
ebrTwoPortStatic OBJECT IDENTIFIER .1.3.6.1.4.1.36.2.18.1.4.6 |
ebrTwoPortStaticTableA table that contains static destination and source
address filtering information about unicast and
multicast addresses for 2-port bridges. SEQUENCE OF EbrTwoPortStaticEntry .1.3.6.1.4.1.36.2.18.1.4.6.1 |
ebrTwoPortStaticEntryInformation about a specific MAC address
for which the bridge has some static forwarding and/or
filtering information. EbrTwoPortStaticEntry .1.3.6.1.4.1.36.2.18.1.4.6.1.1 |
ebrTwoPortAddressThe destination/source MAC Address in a frame to
which this entry's filtering information applies.rw OCTET STRING .1.3.6.1.4.1.36.2.18.1.4.6.1.1.1 |
ebrTwoPortPortNumThe Port Number to which this address will be
locked-down, if the status is lockDown. Otherwise,
this field has a value of 0.rw INTEGER .1.3.6.1.4.1.36.2.18.1.4.6.1.1.2 |
ebrTwoPortStatusThe status of this entry. The meanings of the
values are:
lockDown(1) : This address is 'locked-down' to the
port specified by the ebrTwoPortPortNum field.
This address will be allowed to source frames
only from the specified port, and frames destined
to this address will be sent out only on the
specified port.
hello(2) : This is the address used by the bridge in
the destination field of Spanning Tree Hellos.
It is not a writeable value.
invalid(3) : Writing this value to the object removes
the corresponding entry.
filter(4) : Frames with this address in the source or
destination field will be filtered by the bridge.
forward(5) : Frames with this address in the
destination field will be forwarded by the bridge.
rateLimit(6) : Frames with this address in the
destination field will be rate-limited by the
bridge, if it supports rate limiting. Applicable
only to multicast addresses. For more detail, please
see the ebrRateLimiting group.rw Enumeration .1.3.6.1.4.1.36.2.18.1.4.6.1.1.3 |
ebrMultiPortStatic OBJECT IDENTIFIER .1.3.6.1.4.1.36.2.18.1.4.7 |
ebrMultiPortStaticTableA table that contains static destination and source
address filtering information about unicast and
multicast addresses for multi-port bridges. SEQUENCE OF EbrMultiPortStaticEntry .1.3.6.1.4.1.36.2.18.1.4.7.1 |
ebrMultiPortStaticEntryInformation about a specific MAC address
for which the bridge has some static forwarding and/or
filtering information. EbrMultiPortStaticEntry .1.3.6.1.4.1.36.2.18.1.4.7.1.1 |
ebrMultiPortAddressThe destination/source MAC Address in a frame to
which this entry's filtering information applies.rw OCTET STRING .1.3.6.1.4.1.36.2.18.1.4.7.1.1.1 |
ebrMultiPortReceivePortThe port from which a frame must be received to use
the corresponding ebrMultiPortAllowedToGoTo field. A value
of zero indicates that this entry applies on all ports of
the bridge.rw INTEGER .1.3.6.1.4.1.36.2.18.1.4.7.1.1.2 |
ebrMultiPortAllowedToGoToThe set of ports to which frames received from
a specific port and sourced from or destined to
the address specified by ebrMultiPortAddress are
allowed to be forwarded. Each octet within the
value of this object specifies a set of eight ports,
with the first octet specifying ports 1 through 8,
the second octet specifying port 9 through 16 etc.
Within each octet, the most significant bit represents
the lowest numbered port, and the least significant
bit represents the highest numbered port. If a
bit has a value of '1', then the corresponding port
is included in the set of ports; the port is not
included if its bit has a value of '0'.rw OCTET STRING .1.3.6.1.4.1.36.2.18.1.4.7.1.1.3 |
ebrMultiPortPortNumThe Port Number to which this address will be
locked-down, if the status is lockDown. Otherwise,
this field has a value of zero.rw INTEGER .1.3.6.1.4.1.36.2.18.1.4.7.1.1.4 |
ebrMultiPortStatusThe status of this entry. The meanings of the
values are:
portMask(1) : The static filtering for this address
is specified by the MultiPortAllowedToGoTo field.
lockDown(2) : The static filtering for this address
is specified as 'locked-down' to the port specified
by the ebrMultiPortPortNum field. This address will
be allowed to source frames only from the specified
port, and frames destined to this address will be
sent out only on the specified port.
maskAndLock(3) : The static filtering for this
address is specified by both the
ebrMultiPortAllowedToGoTo as well as 'locked-down'
as explained above for 'lockDown(2)'.
hello(4) : This is the address used by the bridge in
the destination field of Spanning Tree Hellos.
It is not a writeable value.
filter(5) : This address will be filtered on all ports.
invalid(6) : Writing this value to the object removes
the corresponding entry.
rateLimit(7) : Frames with this address in the
destination field will be rate-limited by the
bridge, if it supports rate limiting. Applicable
only to multicast addresses. For more detail, please
see the ebrRateLimiting group.rw Enumeration .1.3.6.1.4.1.36.2.18.1.4.7.1.1.5 |
ebrTwoProtoFilt OBJECT IDENTIFIER .1.3.6.1.4.1.36.2.18.1.4.8 |
ebrTwoProtoEnetFilterOtherAction taken by the bridge on Ethernet protocol types
other than those specified in the ebrTwoEnetProtoTable.rw Enumeration .1.3.6.1.4.1.36.2.18.1.4.8.1 |
ebrTwoProtoSapFilterOtherAction taken by the bridge on 802.2 DSAPs other than
those specified in the ebrTwoSapProtoTable.rw Enumeration .1.3.6.1.4.1.36.2.18.1.4.8.2 |
ebrTwoProtoSnapFilterOtherAction taken by the bridge on the 5-byte SNAP PIDs other
than those specified in the ebrTwoSnapProtoTable.rw Enumeration .1.3.6.1.4.1.36.2.18.1.4.8.3 |
ebrTwoEnetProtoTableA table that contains filtering information about
Ethernet protocol types for 2-port bridges. SEQUENCE OF EbrTwoEnetProtoEntry .1.3.6.1.4.1.36.2.18.1.4.8.4 |
ebrTwoEnetProtoEntryA table that contains filtering information about
Ethernet protocol types for 2-port bridges. EbrTwoEnetProtoEntry .1.3.6.1.4.1.36.2.18.1.4.8.4.1 |
ebrTwoEnetProtoTypeThe protocol type in a frame to which this entry's
filtering information applies.rw OCTET STRING .1.3.6.1.4.1.36.2.18.1.4.8.4.1.1 |
ebrTwoEnetProtoStatusAction taken by bridge when it sees this ethernet
protocol type in a received frame. The meanings of
the values are:
forward(1) : Frames received with this protocol type
are allowed to be forwarded.
filter(2) : Frames received with this protocol type
should be filtered.
invalid(3) : Writing this value to the object removes
the corresponding entry.
rateLimit(4) : Frames received with this protocol type
will be rate-limited by the bridge, if it supports
rate limiting. For more detail, please
see the ebrRateLimiting group.rw Enumeration .1.3.6.1.4.1.36.2.18.1.4.8.4.1.2 |
ebrTwoSapProtoTableA table that contains filtering information about
802.2 SAPs in the DSAP field for 2-port bridges. SEQUENCE OF EbrTwoSapProtoEntry .1.3.6.1.4.1.36.2.18.1.4.8.5 |
ebrTwoSapProtoEntryA table that contains filtering information about
802.2 SAPs in the DSAP field for 2-port bridges. EbrTwoSapProtoEntry .1.3.6.1.4.1.36.2.18.1.4.8.5.1 |
ebrTwoSapIndexIndex of the SAP table.ro INTEGER .1.3.6.1.4.1.36.2.18.1.4.8.5.1.1 |
ebrTwoSapValueThe 802.2 DSAP in a frame to which this entry's
filtering information applies.rw OCTET STRING .1.3.6.1.4.1.36.2.18.1.4.8.5.1.2 |
ebrTwoSapStatusAction taken by bridge when it sees this 802.2 SAP
in the DSAP field of a received frame. The meanings of
the values are:
forward(1) : Frames received with this sap
are allowed to be forwarded.
filter(2) : Frames received with this sap
should be filtered.
invalid(3) : Writing this value to the object removes
the corresponding entry.
rateLimit(4) : Frames received with this sap
will be rate-limited by the bridge, if it supports
rate limiting. For more detail, please
see the ebrRateLimiting group.rw Enumeration .1.3.6.1.4.1.36.2.18.1.4.8.5.1.3 |
ebrTwoSnapProtoTableA table that contains filtering information about
5-byte SNAP PIDs for 2-port bridges. SEQUENCE OF EbrTwoSnapProtoEntry .1.3.6.1.4.1.36.2.18.1.4.8.6 |
ebrTwoSnapProtoEntryA table that contains filtering information about
5-byte SNAP PIDs for 2-port bridges. EbrTwoSnapProtoEntry .1.3.6.1.4.1.36.2.18.1.4.8.6.1 |
ebrTwoSnapIndexThe index into the SNAP table.ro INTEGER .1.3.6.1.4.1.36.2.18.1.4.8.6.1.1 |
ebrTwoSnapValueThe SNAP PID in an 802 frame to which this entry's
filtering information applies.rw OCTET STRING .1.3.6.1.4.1.36.2.18.1.4.8.6.1.2 |
ebrTwoSnapStatusAction taken by bridge when it sees this SNAP PID
in a received 802 frame. The meanings of
the values are:
forward(1) : Frames received with this snap pid
are allowed to be forwarded.
filter(2) : Frames received with this snap pid
should be filtered.
invalid(3) : Writing this value to the object removes
the corresponding entry.
rateLimit(4) : Frames received with this snap pid
will be rate-limited by the bridge, if it supports
rate limiting. For more detail, please
see the ebrRateLimiting group.rw Enumeration .1.3.6.1.4.1.36.2.18.1.4.8.6.1.3 |
ebrMultiProtoFilt OBJECT IDENTIFIER .1.3.6.1.4.1.36.2.18.1.4.9 |
ebrMultiEnetProtoTableA table that contains filtering information about
Ethernet protocol types for multi-port bridges. SEQUENCE OF EbrMultiEnetProtoEntry .1.3.6.1.4.1.36.2.18.1.4.9.1 |
ebrMultiEnetProtoEntryA table that contains filtering information about
Ethernet protocol types for multi-port bridges. EbrMultiEnetProtoEntry .1.3.6.1.4.1.36.2.18.1.4.9.1.1 |
ebrMultiEnetProtoTypeThe protocol type in a frame to which this entry's
filtering information applies.rw OCTET STRING .1.3.6.1.4.1.36.2.18.1.4.9.1.1.1 |
ebrMultiEnetReceivePortThe port from which a frame must be received to use
the corresponding ebrMultiPortEnetProtoType field. A value
of zero indicates that this entry applies on all ports of
the bridge.rw INTEGER .1.3.6.1.4.1.36.2.18.1.4.9.1.1.2 |
ebrMultiEnetAllowedToGoToThe set of ports to which frames received from
a specific port and containing the protocol
type specified by ebrMultiEnetProtoType are
allowed to be forwarded. Each octet within the
value of this object specifies a set of eight ports,
with the first octet specifying ports 1 through 8,
the second octet specifying port 9 through 16 etc.
Within each octet, the most significant bit represents
the lowest numbered port, and the least significant
bit represents the highest numbered port. If a
bit has a value of '1', then the corresponding port
is included in the set of ports; the port is not
included if its bit has a value of '0'.rw OCTET STRING .1.3.6.1.4.1.36.2.18.1.4.9.1.1.3 |
ebrMultiEnetStatusAction taken by bridge when it sees this ethernet
protocol type in a received frame. The meanings of
the values are:
portMask(1) : The static filtering for this address
is specified by the MultiEnetAllowedToGoTo field.
invalid(2) : Writing this value to the object removes
the corresponding entry.
filter(3) : Frames received with this protocol type
should be filtered.
forward(4) : Frames received with this protocol type
are allowed to be forwarded.
rateLimit(5) : Frames received with this protocol type
will be rate-limited by the bridge, if it supports
rate limiting. For more detail, please
see the ebrRateLimiting group.rw Enumeration .1.3.6.1.4.1.36.2.18.1.4.9.1.1.4 |
ebrMultiSapProtoTableA table that contains filtering information about
802.2 SAPs in the DSAP field for multi-port bridges. SEQUENCE OF EbrMultiSapProtoEntry .1.3.6.1.4.1.36.2.18.1.4.9.2 |
ebrMultiSapProtoEntryA table that contains filtering information about
802.2 SAPs in the DSAP field for multi-port bridges. EbrMultiSapProtoEntry .1.3.6.1.4.1.36.2.18.1.4.9.2.1 |
ebrMultiSapValueThe 802.2 DSAP in a frame to which this entry's
filtering information applies.rw OCTET STRING .1.3.6.1.4.1.36.2.18.1.4.9.2.1.1 |
ebrMultiSapReceivePortThe port from which a frame must be received to use
the corresponding ebrMultiPortSapProtoType field. A value
of zero indicates that this entry applies on all ports of
the bridge.rw INTEGER .1.3.6.1.4.1.36.2.18.1.4.9.2.1.2 |
ebrMultiSapAllowedToGoToThe set of ports to which frames received from
a specific port and containing the DSAP in an 802
frame specified by ebrMultiSapValue are
allowed to be forwarded. Each octet within the
value of this object specifies a set of eight ports,
with the first octet specifying ports 1 through 8,
the second octet specifying port 9 through 16 etc.
Within each octet, the most significant bit represents
the lowest numbered port, and the least significant
bit represents the highest numbered port. If a
bit has a value of '1', then the corresponding port
is included in the set of ports; the port is not
included if its bit has a value of '0'.rw OCTET STRING .1.3.6.1.4.1.36.2.18.1.4.9.2.1.3 |
ebrMultiSapStatusAction taken by bridge when it sees this 802.2 SAP
in the DSAP field of a received frame. The meanings of
the values are:
portMask(1) : The static filtering for this address
is specified by the MultiSapAllowedToGoTo field.
invalid(2) : Writing this value to the object removes
the corresponding entry.
filter(3) : Frames received with this protocol type
should be filtered.
forward(4) : Frames received with this protocol type
are allowed to be forwarded.
rateLimit(5) : Frames received with this protocol type
will be rate-limited by the bridge, if it supports
rate limiting. For more detail, please
see the ebrRateLimiting group.rw Enumeration .1.3.6.1.4.1.36.2.18.1.4.9.2.1.4 |
ebrMultiSnapProtoTableA table that contains filtering information about
5-byte SNAP PIDs for multi-port bridges. SEQUENCE OF EbrMultiSnapProtoEntry .1.3.6.1.4.1.36.2.18.1.4.9.3 |
ebrMultiSnapProtoEntryA table that contains filtering information about
5-byte SNAP PIDs for multi-port bridges. EbrMultiSnapProtoEntry .1.3.6.1.4.1.36.2.18.1.4.9.3.1 |
ebrMultiSnapValueThe SNAP PID in an 802 frame to which this entry's
filtering information applies.rw OCTET STRING .1.3.6.1.4.1.36.2.18.1.4.9.3.1.1 |
ebrMultiSnapReceivePortThe port from which a frame must be received to use
the corresponding ebrMultiPortSnapProtoType field. A value
of zero indicates that this entry applies on all ports of
the bridge.rw INTEGER .1.3.6.1.4.1.36.2.18.1.4.9.3.1.2 |
ebrMultiSnapAllowedToGoToThe set of ports to which frames received from
a specific port and containing the SNAP PID in an
802 frame specified by ebrMultiSnapValue are
allowed to be forwarded. Each octet within the
value of this object specifies a set of eight ports,
with the first octet specifying ports 1 through 8,
the second octet specifying port 9 through 16 etc.
Within each octet, the most significant bit represents
the lowest numbered port, and the least significant
bit represents the highest numbered port. If a
bit has a value of '1', then the corresponding port
is included in the set of ports; the port is not
included if its bit has a value of '0'.rw OCTET STRING .1.3.6.1.4.1.36.2.18.1.4.9.3.1.3 |
ebrMultiSnapStatusAction taken by bridge when it sees this SNAP PID
in a received 802 frame. The meanings of
the values are:
portMask(1) : The static filtering for this address
is specified by the MultiSnapAllowedToGoTo field.
invalid(2) : Writing this value to the object removes
the corresponding entry.
filter(3) : Frames received with this protocol type
should be filtered.
forward(4) : Frames received with this protocol type
are allowed to be forwarded.
rateLimit(5) : Frames received with this protocol type
will be rate-limited by the bridge, if it supports
rate limiting. For more detail, please
see the ebrRateLimiting group.rw Enumeration .1.3.6.1.4.1.36.2.18.1.4.9.3.1.4 |
ebrMultiFiltSw OBJECT IDENTIFIER .1.3.6.1.4.1.36.2.18.1.4.10 |
ebrMultiSwTableA list of interface entries. The number of entries is
given by ifNumber, defined in MIB-II. SEQUENCE OF EbrMultiSwEntry .1.3.6.1.4.1.36.2.18.1.4.10.1 |
ebrMultiSwEntryA collection of objects containing information for a
given interface. EbrMultiSwEntry .1.3.6.1.4.1.36.2.18.1.4.10.1.1 |
ebrMultiSwIndexIdentifies the Interface to which this entry applies.ro INTEGER .1.3.6.1.4.1.36.2.18.1.4.10.1.1.1 |
ebrMultiSwManualFilterA switch that controls address filtering. When true,
the bridge purges the learned entries from its forwarding
database, stops its learning process, and forwards only
frames with destination and source addresses that have
been specified via management.rw Enumeration .1.3.6.1.4.1.36.2.18.1.4.10.1.1.2 |
ebrMultiSwProtoEnetOtherAction taken by the bridge on Ethernet protocol types
other than those specified in the ebrMultiEnetProtoTable.rw Enumeration .1.3.6.1.4.1.36.2.18.1.4.10.1.1.3 |
ebrMultiSwProtoSapOtherAction taken by the bridge on 802.2 DSAPs other
than those specified in the ebrMultiSapProtoTable.rw Enumeration .1.3.6.1.4.1.36.2.18.1.4.10.1.1.4 |
ebrMultiSwProtoSnapOtherAction taken by the bridge on the 5-byte SNAP PIDs other
than those specified in the ebrMultiSnapProtoTable.rw Enumeration .1.3.6.1.4.1.36.2.18.1.4.10.1.1.5 |
ebrNTP OBJECT IDENTIFIER .1.3.6.1.4.1.36.2.18.1.4.11 |
ebrNTPTableA table of Ethernet protocol types which will
selectively be translated in such a way as to guarantee
that the form in which a packet was received - Ethernet PT
or 802.3 with 1042 format and this PT - will be retained
across a pair of these bridges. SEQUENCE OF EbrNTPEntry .1.3.6.1.4.1.36.2.18.1.4.11.1 |
ebrNTPEntryA list of NTP protocol type entries. EbrNTPEntry .1.3.6.1.4.1.36.2.18.1.4.11.1.1 |
ebrNTPtypeA protocol type in the NTP table.rw OCTET STRING .1.3.6.1.4.1.36.2.18.1.4.11.1.1.1 |
ebrNTPStatusWriting invalid(2) to this object removes the corresponding
entry. When read, this object always returns a value
of other(1).rw Enumeration .1.3.6.1.4.1.36.2.18.1.4.11.1.1.2 |
esysIPXSwitchA software switch that, when set to true, causes the
bridge to translate IPX 'raw 802.3' packets into SNAP
encapsulated packets on the FDDI. Note that this works
only in environments where all IPX stations use only
this particular format. It is recommended that the
Ethernet v2 format be used on IPX stations for
full connectivity of IPX stations across Ethernet
as well as FDDI bridged and routed networks.rw Enumeration .1.3.6.1.4.1.36.2.18.1.4.11.2 |
ebrRateLimiting OBJECT IDENTIFIER .1.3.6.1.4.1.36.2.18.1.4.12 |
ebrRateLimitSwitchBy default, rate limiting will be disabled. It can be
enabled by setting this object to 'true(1)'.rw Enumeration .1.3.6.1.4.1.36.2.18.1.4.12.1 |
ebrRateLimitThis is the maximum number of rate-limited frames per second
that the bridge will forward per second.rw INTEGER .1.3.6.1.4.1.36.2.18.1.4.12.2 |
ebrRateLimitCounterTableA table of the count of frames that were dropped by
the bridge due to rate limiting on each port. SEQUENCE OF EbrRateLimitCounterEntry .1.3.6.1.4.1.36.2.18.1.4.12.3 |
ebrRateLimitCounterEntryA list of rate limited frame counter entries. EbrRateLimitCounterEntry .1.3.6.1.4.1.36.2.18.1.4.12.3.1 |
ebrRateLimitPortThe port for which this entry contains rate limit
counters information.ro INTEGER .1.3.6.1.4.1.36.2.18.1.4.12.3.1.1 |
ebrRateLimitAddressFramesThis is the number of frames per second that were
filtered due to address rate limiting.ro Counter .1.3.6.1.4.1.36.2.18.1.4.12.3.1.2 |
ebrRateLimitProtocolFramesThis is the number of frames per second that were
filtered due to protocol rate limiting.ro Counter .1.3.6.1.4.1.36.2.18.1.4.12.3.1.3 |
eauth OBJECT IDENTIFIER .1.3.6.1.4.1.36.2.18.1.5 |
eauth1 OBJECT IDENTIFIER .1.3.6.1.4.1.36.2.18.1.5.1 |
eauthTrapCommunityThe community string used in SNMP Trap PDUs.rw OCTET STRING .1.3.6.1.4.1.36.2.18.1.5.1.1 |
eauthTrapUserTableA list of addresses to which traps will be sent and
associated information. SEQUENCE OF EauthTrapUserEntry .1.3.6.1.4.1.36.2.18.1.5.1.2 |
eauthTrapUserEntryObjects containing information for a given trap address. EauthTrapUserEntry .1.3.6.1.4.1.36.2.18.1.5.1.2.1 |
eauthTrapUserAddrAn IP Address to which all SNMP Trap messages will be sent.rw IpAddress .1.3.6.1.4.1.36.2.18.1.5.1.2.1.1 |
eauthTrapUserStatusWriting invalid(2) to this object removes the corresponding
entry. When read, this object always returns a value
of other(1).rw Enumeration .1.3.6.1.4.1.36.2.18.1.5.1.2.1.2 |
eauthReadOnlyCommunityThe community string used to identify an SNMP community
with access rights of Read-only.rw OCTET STRING .1.3.6.1.4.1.36.2.18.1.5.1.3 |
eauthReadOnlyUserTableA list of Read-only users and associated information. SEQUENCE OF EauthReadOnlyUserEntry .1.3.6.1.4.1.36.2.18.1.5.1.4 |
eauthReadOnlyUserEntryObjects containing information for a given Read-only user. EauthReadOnlyUserEntry .1.3.6.1.4.1.36.2.18.1.5.1.4.1 |
eauthReadOnlyUserAddrAn IP Address, or a set of IP addresses, which has
Read-only SNMP access to this agent. If this object
is used as a wildcard, bits corresponding to the
zero bits in the corresponding euthReadOnlyUserMask
are treated as don't-care.rw IpAddress .1.3.6.1.4.1.36.2.18.1.5.1.4.1.1 |
eauthReadOnlyUserMaskA 32-bit mask which is applied to (ANDed with)
the source IP address of an incoming SNMP message.
If the result of the mask is equal to eauthReadOnlyUserAddr,
the message is considered to have come from a user
who has Read-only access. This allows wildcarding,
for example, for all NMS's on a given subnet. For
fully specified IP addresses required to be in this
community, this mask may be set to all 1's.rw OCTET STRING .1.3.6.1.4.1.36.2.18.1.5.1.4.1.2 |
eauthReadOnlyUserStatusWriting invalid(2) to this object removes the corresponding
entry. When read, this object always returns a value
of other(1).rw Enumeration .1.3.6.1.4.1.36.2.18.1.5.1.4.1.3 |
eauthReadWriteCommunityThe community string used to identify an SNMP community
with access rights of Read-Write.rw OCTET STRING .1.3.6.1.4.1.36.2.18.1.5.1.5 |
eauthReadWriteUserTableA list of Read-Write users and associated information. SEQUENCE OF EauthReadWriteUserEntry .1.3.6.1.4.1.36.2.18.1.5.1.6 |
eauthReadWriteUserEntryObjects containing information for a given Read-Write user. EauthReadWriteUserEntry .1.3.6.1.4.1.36.2.18.1.5.1.6.1 |
eauthReadWriteUserAddrAn IP Address, or a set of IP addresses, which has
Read-Write SNMP access to this agent. If this object
is used as a wildcard, bits corresponding to the
zero bits in the corresponding euthReadWriteUserMask
are treated as don't-care.rw IpAddress .1.3.6.1.4.1.36.2.18.1.5.1.6.1.1 |
eauthReadWriteUserMaskA 32-bit mask which is applied to (ANDed with)
the source IP address of an incoming SNMP message.
If the result of the mask is equal to eauthReadWriteUserAddr,
the message is considered to have come from a user
who has Read-Write access. This allows wildcarding,
for example, for all NMS's on a given subnet. For
fully specified IP addresses required to be in this
community, this mask may be set to all 1's.rw OCTET STRING .1.3.6.1.4.1.36.2.18.1.5.1.6.1.2 |
eauthReadWriteUserStatusWriting invalid(2) to this object removes the corresponding
entry. When read, this object always returns a value
of other(1).rw Enumeration .1.3.6.1.4.1.36.2.18.1.5.1.6.1.3 |