CT-ELS100-MIB
AI MIB Summary
Standard SNMP MIB module defining data structures for CT-ELS100-MIB.
147
Objects
Active
Status
4
Dependencies
Imported Objects
Objects
147 total| Object Name |
|---|
kxPortFunctionsTrapSent whenever the current functional state (active
protocols) of the port has changed. TRAP-TYPE .1.3.6.1.2.1.1.2.0.1 |
kxRxQueuesTrapSent whenever the number of times that the port's
receiver has stopped receiving packets due to buffer
space shortages has exceeded the port's limit. TRAP-TYPE .1.3.6.1.2.1.1.2.0.2 |
kxTxStormFlagTrapSent whenever multicast storm protection has been
invoked for the port. TRAP-TYPE .1.3.6.1.2.1.1.2.0.3 |
kxTxCongestsTrapSent whenever packets destined for the unit itself
were discarded due to lack of buffer space. TRAP-TYPE .1.3.6.1.2.1.1.2.0.4 |
kxTrunkStateTrapA trunking state change transition has occurred. The
possible transitions are:
Closed-Oneway
Oneway-Perturbed
Perturbed-Joined
Joined-Helddown
Closed-Helddown
Oneway-Helddown
Perturbed-Helddown TRAP-TYPE .1.3.6.1.2.1.1.2.0.5 |
kxTrunkBridgeAddrTrapThe associated trunking MAC address of the bridge ID
of the remote bridge has changed. TRAP-TYPE .1.3.6.1.2.1.1.2.0.6 |
kxTrunkIPAddrTrapThe associated trunking IP address of the remote
bridge has changed. TRAP-TYPE .1.3.6.1.2.1.1.2.0.7 |
kxTrunkErrorTrapAn error has occurred in trunking. TRAP-TYPE .1.3.6.1.2.1.1.2.0.8 |
kxTrunkLinkOrdinalTrapThe port's index in the trunking group has changed. TRAP-TYPE .1.3.6.1.2.1.1.2.0.9 |
kxTrunkLinkCountTrapThe number of ports in the trunking group has
changed. TRAP-TYPE .1.3.6.1.2.1.1.2.0.10 |
kxDiagUnitBootedTrapThe unit has booted. kxadminFatalErr contains
information about why the unit rebooted. TRAP-TYPE .1.3.6.1.2.1.1.2.0.11 |
kxStorageFailureTrapSent if the unit's Configuration EEPROM has
failed. The unit will not be able to reboot, and must
be returned to the factory. TRAP-TYPE .1.3.6.1.2.1.1.2.0.12 |
kxIfErrorsTrapSent whenever the number of hardware errors in
received and transmitted packets has exceeded the
port's limit. TRAP-TYPE .1.3.6.1.2.1.1.2.0.13 |
sigma OBJECT IDENTIFIER .1.3.6.1.4.1.97 |
IMPORTS Unknown .1.3.6.1.4.1.97 |
sys OBJECT IDENTIFIER .1.3.6.1.4.1.97.1 |
sysIDAn integer which serves to identify the type of SmartStack.ro Enumeration .1.3.6.1.4.1.97.1.1 |
sysResetThe time, in centiseconds, before the device should
reboot. A GetResponse value of zero indicates that no
reboot time has been specified.rw TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.97.1.2 |
sysTrapPortZero, or the UDP port number to which a second copy
of SNMP traps should be sent. Valid values are zero
through 65535.rw INTEGER .1.3.6.1.4.1.97.1.3 |
els-100 OBJECT IDENTIFIER .1.3.6.1.4.1.97.8 |
kxhw OBJECT IDENTIFIER .1.3.6.1.4.1.97.8.1 |
kxhwDiagCodeAdditional diagnostics information concerning the
slot's module.ro OCTET STRING .1.3.6.1.4.1.97.8.1.1 |
kxhwManufDataA 24-byte array which contains the part number,
serial number and hardware revision level of this
module.ro OCTET STRING .1.3.6.1.4.1.97.8.1.2 |
kxhwPortCountro INTEGER .1.3.6.1.4.1.97.8.1.3 |
kxsw OBJECT IDENTIFIER .1.3.6.1.4.1.97.8.2 |
kxswNumberThe number of file sets. The default is 2.ro INTEGER .1.3.6.1.4.1.97.8.2.1 |
kxswFilesetTableA list of the software file sets stored. The first
file set refers to the one that was used when ELS-100
last booted. The second file set refers to the one
which will be used when ELS-100 reboots or reloads any
hardware module. SEQUENCE OF KxswFilesetEntry .1.3.6.1.4.1.97.8.2.2 |
kxswFilesetEntryA set of objects for each file set. KxswFilesetEntry .1.3.6.1.4.1.97.8.2.2.1 |
kxswIndexThe file set number, beginning with 1 for the first
file set. This number always matches the instance of
the swFiles. For example, {swIndex 2} contains the
value '2'.ro Enumeration .1.3.6.1.4.1.97.8.2.2.1.1 |
kxswDescThe description (0-255 bytes) of the software file
set.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.97.8.2.2.1.2 |
kxswCountThe number of files in the file set. This number may
range from 1 to 255.ro INTEGER .1.3.6.1.4.1.97.8.2.2.1.3 |
kxswTypeThe types of the files within the file set.ro OCTET STRING .1.3.6.1.4.1.97.8.2.2.1.4 |
kxswSizesAn array (4 octets per file), containing the size of
each of the files. Each size is encoded as a series
of 4 bytes, which should be converted into a 32 bit
integer.ro OCTET STRING .1.3.6.1.4.1.97.8.2.2.1.5 |
kxswStartsAn array (4 octets per file), containing the
software's execution starting address of each of the
files. Each address is encoded as a series of 4 bytes,
which should be converted into a 32 bit integer.ro OCTET STRING .1.3.6.1.4.1.97.8.2.2.1.6 |
kxswBasesAn array (4 octets per file), containing the
software's base loading address of each of the
files. Each address is encoded as a series of 4 bytes,
which should be converted into a 32 bit integer.ro OCTET STRING .1.3.6.1.4.1.97.8.2.2.1.7 |
kxswFlashBankThe bank number where the software file set resides.ro Enumeration .1.3.6.1.4.1.97.8.2.2.1.8 |
kxadmin OBJECT IDENTIFIER .1.3.6.1.4.1.97.8.3 |
kxadminFatalErrThis is a 32 byte array which contains information
about the cause of the previous system reset. This
will describe the circumstances which forced the
system software to perform a reboot. The values in the
first byte have the following meanings (0) Power
failure, (1) Watchdog Timeout, (2) NMS Requested
Shutdown, (3-255) Fatal Error (next byte contains the
hwIndex of the module which encountered the error;
remaining 30 bytes contain additional information).ro OCTET STRING .1.3.6.1.4.1.97.8.3.1 |
kxadminAnyPassThe authentication password (0-24 bytes) which must
match the community name in an SNMP PDU, in order for
the operation to be performed. A zero length password
indicates that any community name is acceptable.rw OCTET STRING .1.3.6.1.4.1.97.8.3.2 |
kxadminGetPassThe authentication password (0-24 bytes) which must
match the community name in an SNMP Get PDU (except
for Debug or password parameters). A zero length
password indicates that any community name is
acceptable. Alternatively, it is acceptable if the
community name matches configAnyPass.rw OCTET STRING .1.3.6.1.4.1.97.8.3.3 |
kxadminNMSIPAddrThe address of the NMS to which Trap PDUs are to be
sent. A value of zero indicates that Trap PDUs should
be sent to the NMS last heard from.rw IpAddress .1.3.6.1.4.1.97.8.3.4 |
kxadminStorageFailureWhether the ELS-100's storage facility for its
configuration parameters has failed (the ELS-100 may
not be able to reboot after such a failure).ro Enumeration .1.3.6.1.4.1.97.8.3.5 |
kxadminAuthenticationFailureAll nulls, or the IP source address within the last
SNMP PDU which caused an SNMP authentication failure.ro IpAddress .1.3.6.1.4.1.97.8.3.6 |
kxadminNAMReceiveCongestsro Counter .1.3.6.1.4.1.97.8.3.7 |
kxadminArpEntriesThe number of ARP entries for all interfaces.ro Counter .1.3.6.1.4.1.97.8.3.8 |
kxadminArpStaticsThe number of statically defined ARP entries for all
interfaces.ro Counter .1.3.6.1.4.1.97.8.3.9 |
kxadminArpOverflowsThe number of times a ARP entry could not be learned
due to insufficient address table space.ro Counter .1.3.6.1.4.1.97.8.3.10 |
kxadminRipPreferenceThe value to assign to ipRouteMetric2, when adding a
RIP-learned entry to the IP Routing Table.rw INTEGER .1.3.6.1.4.1.97.8.3.11 |
kxadminRipRouteDiscardsThe number of times a route learned via RIP was not
added to the IP Routing Table due to insufficient
Routing Table space.ro Counter .1.3.6.1.4.1.97.8.3.12 |
kxadminRebootConfigThe configuration file that will be used when the
ELS-100 reboots. This parameter is normally
automatically set by the ELS-100; however, an NMS may
explicitly set it to either no-change (1) or
revert-to-defaults (3).rw Enumeration .1.3.6.1.4.1.97.8.3.13 |
kxadminDisableButtonrw Enumeration .1.3.6.1.4.1.97.8.3.14 |
kxadminButtonSelectionrw Enumeration .1.3.6.1.4.1.97.8.3.15 |
kxadminLEDProgramOptionrw Enumeration .1.3.6.1.4.1.97.8.3.16 |
kxswdis OBJECT IDENTIFIER .1.3.6.1.4.1.97.8.4 |
kxswdisDescThe description (0-32 bytes) of the software set
currently being downloaded, or a description of the
software set last downloaded since the ELS100-16
booted.ro OCTET STRING .1.3.6.1.4.1.97.8.4.1 |
kxswdisAccessThe version of software that may be
downloaded. Attempts to download other versions of
software will be rejected. The value for swdisAccess
is embedded within the software files that are to be
distributed via TFTP. Its value may be derived from
the names of the software files. The NMS operator may
wish to use the following special values: protected
(1) No software downloads will be accepted
any-software (2) A software download of any version
of new software will be accepted - this is the factory
defaultrw Enumeration .1.3.6.1.4.1.97.8.4.2 |
kxswdisWriteStatusThe status of the erase/write operation.ro Enumeration .1.3.6.1.4.1.97.8.4.3 |
kxswdisConfigIpThe IP address of the NMS (i.e., any IP host) that is
allowed to use TFTP to send/retrieve the configuration
file of the ELS100-16. A value of 0.0.0.0 (which is
the factory specified default) prevents any NMS from
obtaining access, while a value of 255.255.255.255
gives every NMS permission.rw IpAddress .1.3.6.1.4.1.97.8.4.4 |
kxswdisConfigRetryTimeThe number of seconds that the ELS-100 will wait for
an acknowledgment before it retransmits an
unacknowledged TFTP data block. The factory specified
default is 5 seconds.rw INTEGER .1.3.6.1.4.1.97.8.4.5 |
kxswdisConfigTotalTimeoutThe number of seconds that the ELS-100 will wait for
an acknowledgment to a data block before it cancels a
TFTP session. The factory specified default is 25
seconds.rw INTEGER .1.3.6.1.4.1.97.8.4.6 |
kxaddr OBJECT IDENTIFIER .1.3.6.1.4.1.97.8.5 |
kxaddrStaticsThe number of static addresses which are currently
stored in the ELS100-16.ro Counter .1.3.6.1.4.1.97.8.5.1 |
kxaddrDynamicsThe number of learned addresses in the address table.ro Counter .1.3.6.1.4.1.97.8.5.2 |
kxaddrDynamicMaxThe maximum number of spanning tree addresses which
have been learned since the ELS100-16 was last booted
(or this parameter was last reset by the NMS).rw Gauge .1.3.6.1.4.1.97.8.5.3 |
kxaddrDynamicOverflowsThe number times an address was not learned due to
insufficient address table space.ro Counter .1.3.6.1.4.1.97.8.5.4 |
kxaddrFlagsFlags to describe the use and control of this address
entry. Each bit has a different meaning. The NMS must
always set either entry-static, entry-none, or
entry-mesh; however, for GetRequests, the NMS will see
either no bits set (if the entry does not exist), or
exactly one of the following bits set:
entry-dynamic-local = 30, entry-dynamic-remote = 29,
entry-static = 28, entry-other = 27, entry-none = 26,
entry-mesh = 25, entry-statistics = 24, Bit 31 is
reserved.
Any combination of the restriction bits (bits 23-21)
may be set for any type of entry, except entry-other
or entry-mesh: entry-no-source = 23, entry-no-multi =
22, Bit 21 is reserved, Bits 20-18 are reserved.
Exactly one of the special entry bits (bits 17-10)
must be set for entry-other entries, and none of the
bits may be set for other than entry-other entries:
entry-all-lmas = 17, entry-any-lma = 16, entry-lma =
15, entry-port = 14, entry-bpdu = 13, entry-reserved =
12, Bits 11-10 are reserved for future expansion. Bits
9-0 are reserved.rw INTEGER .1.3.6.1.4.1.97.8.5.5 |
kxaddrMACThe MAC address for this address definition.rw OCTET STRING .1.3.6.1.4.1.97.8.5.6 |
kxaddrPortThe port through which this address is connected to
the ELS100 (only valid for entry-dynamic-local,
entry-statistics, and entry-port entries).rw INTEGER .1.3.6.1.4.1.97.8.5.7 |
kxaddrOperationThe operation to be performed upon the described
address. The possibilities include: read-random (1),
read-next (2), update (4), delete (5), read-block (6).rw Enumeration .1.3.6.1.4.1.97.8.5.8 |
kxaddrIndexThe index number to be used for read-next and
read-block operations. When the ELS-100 boots,
addrIndex is initialized to -1.rw INTEGER .1.3.6.1.4.1.97.8.5.9 |
kxaddrNextThe next value to use for addrIndex, when you use
read-next or read-block operations to read the address
table. When the ELS-100 boots, addrNext is initialized
to -1.rw INTEGER .1.3.6.1.4.1.97.8.5.10 |
kxaddrBlockSizeThe number of addresses contained by addrBlock. This
parameter is only used for dumping blocks of MAC
addresses.rw INTEGER .1.3.6.1.4.1.97.8.5.11 |
kxaddrBlockA series of 0-700 octets, which represents 0-100
addresses. Each address consists of a 6 octet MAC
address followed by a 1 byte port number. If the port
number is zero, then the address is that of a
specially configured address; otherwise, the address
is a dynamically learned address. This parameter is
only used for dumping blocks of MAC addressesrw OCTET STRING .1.3.6.1.4.1.97.8.5.12 |
kxif OBJECT IDENTIFIER .1.3.6.1.4.1.97.8.6 |
kxifTableA list of interface entries; one per port. SEQUENCE OF KxifEntry .1.3.6.1.4.1.97.8.6.1 |
kxifEntryA set of objects for an interface entry. KxifEntry .1.3.6.1.4.1.97.8.6.1.1 |
kxifIndexThe port number, beginning with 1 for the first
port.ro INTEGER .1.3.6.1.4.1.97.8.6.1.1.1 |
kxifRxCntThe number of small data buffers for receiving
packets.ro INTEGER .1.3.6.1.4.1.97.8.6.1.1.2 |
kxifTxCntThe maximum size of the port's transmit queue, i.e.,
the number of packets that can be in the port's
transmit queue, waiting to be transmitted.ro INTEGER .1.3.6.1.4.1.97.8.6.1.1.3 |
kxifThresholdMaximum number of combined receive and transmit
packet hardware errors before an alarm should be
generated.rw INTEGER .1.3.6.1.4.1.97.8.6.1.1.4 |
kxifThresholdTimeThe time period (in seconds) to which kxifThreshold
applies. A value of zero will disable the
kxifThreshold alarm.rw INTEGER .1.3.6.1.4.1.97.8.6.1.1.5 |
kxifRxQueueThreshMaximum number of receive packet queue overflow
errors before an alarm should be generated.rw INTEGER .1.3.6.1.4.1.97.8.6.1.1.6 |
kxifRxQueueThreshTimeThe time period (in seconds) to which
kxifRxQueueThresh applies. A value of zero will
disable the kxifRxQueueThresh alarm.rw INTEGER .1.3.6.1.4.1.97.8.6.1.1.7 |
kxifFunctionThe current functional state (protocols which have
been activated and are operational) of the port. The
following values or combinations are supported:
0x0001 NMS, 0x0002 TBRIDGE, 0x0020 UNIT_NO_BPDU
0x0040 UNIT_RIP, 0x0800 UNIT_ARP,0x1000 UNIT_DUPLEX_HALF
0x2000 UNIT_DUPLEX_AUTO, 0x8000 UNIT_AUTO
0x10000 UNIT_TRUNKING , 0x40000 UNIT_SPEED_10
These values can be configured through the protoTable.ro INTEGER .1.3.6.1.4.1.97.8.6.1.1.8 |
kxifStatisticsTimeLength of time during which statistics were collected.ro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.97.8.6.1.1.9 |
kxuart OBJECT IDENTIFIER .1.3.6.1.4.1.97.8.7 |
kxuartTableA list of interface entries; one per UART port. SEQUENCE OF KxuartEntry .1.3.6.1.4.1.97.8.7.1 |
kxuartEntryA set of objects for an interface entry. KxuartEntry .1.3.6.1.4.1.97.8.7.1.1 |
kxuartIndexThe ELS-100's port number of the port.ro INTEGER .1.3.6.1.4.1.97.8.7.1.1.1 |
kxuartBaudThis is the desired baud rate. Only 1200 baud
through 19,200 baud are supported by the ELS-100.rw Enumeration .1.3.6.1.4.1.97.8.7.1.1.2 |
kxuartAlignmentErrorsNumber of received packets with frame alignment
errors, since the port was last enabled.ro Counter .1.3.6.1.4.1.97.8.7.1.1.3 |
kxuartOverrunErrorsNumber of received packets with data overrun errors,
since the port was last enabled.ro Counter .1.3.6.1.4.1.97.8.7.1.1.4 |
kxproto OBJECT IDENTIFIER .1.3.6.1.4.1.97.8.8 |
kxprotoTableThis table contains configuration information
specifying the types of protocols used to bridge
and filter frames for each port. SEQUENCE OF KxprotoEntry .1.3.6.1.4.1.97.8.8.1 |
kxprotoEntryEach entry in this table specifies which protocols are
used by a particular port in the SmartStack. KxprotoEntry .1.3.6.1.4.1.97.8.8.1.1 |
kxprotoIfIndexIdentifies the interface (port) to which this entry's
information belongs. The value of this variable
corresponds to ifIndex, as well as most of the other
port identification values in related MIBs.ro INTEGER .1.3.6.1.4.1.97.8.8.1.1.1 |
kxprotoBridgeDefines the bridging method to be applied to frames
received at, or destined for, this port. Ports may be
configured for transparent or none. The UART may only
be configured to none.rw Enumeration .1.3.6.1.4.1.97.8.8.1.1.2 |
kxprotoSuppressBpduAllows transmission of spanning tree protocol packets
to be suppressed. If normal(1), 802.1d spanning tree
packets are transmitted as usual. If suppressed(2),
these packets are not transmitted. This option may be
needed for interoperability with non-802.1d spanning
tree protocols (e.g., DEC LanBridge 100).rw Enumeration .1.3.6.1.4.1.97.8.8.1.1.3 |
kxprotoRipListenSpecifies whether the port should listen for internet
Routing Information Protocol (RFC-1058) packets, in
order to build the routing table for the unit.rw Enumeration .1.3.6.1.4.1.97.8.8.1.1.4 |
kxprotoTrunkingSpecifies whether SmartStack trunking protocol (an
extension to the standard Spanning Tree) is to be
used over this port.rw Enumeration .1.3.6.1.4.1.97.8.8.1.1.5 |
kxtrunk OBJECT IDENTIFIER .1.3.6.1.4.1.97.8.9 |
kxtrunkTableThis table describes the trunking status and attributes of
the interfaces that are configured for bridge trunking. SEQUENCE OF KxtrunkEntry .1.3.6.1.4.1.97.8.9.1 |
kxtrunkEntryAn entry exists in this table for each physical interface
(port) that is configured for trunking. KxtrunkEntry .1.3.6.1.4.1.97.8.9.1.1 |
kxtrunkIfIndexIdentifies a physical interface (port) which is
configured for LAN trunking. The value of this variable
corresponds to ifIndex, as well as most of the other
port identification values in related MIBs.ro INTEGER .1.3.6.1.4.1.97.8.9.1.1.1 |
kxtrunkStateIf off(1) then this link has not been enabled for
trunking. If closed(2) then this link has not yet
received any Trunking PDUs. If oneway(3) then incoming
Trunking PDUs do not indicate that our PDUs are being
successfully received by the far end. If joined(4)
then this link is actively participating in the trunk
group. If perturbed(5) then this link is actively
participating in the trunk group; however, the
transmission of data packets has been temporarily
stopped due to a change in membership of the group.
If helddown(6) then an error has been detected and the
link is being held out-of-service until the error
clears. If broken(7) then this link has been
configured for trunking, but the port is physically
non-operational.ro Enumeration .1.3.6.1.4.1.97.8.9.1.1.2 |
kxtrunkRemoteBridgeAddrThe MAC address portion of the bridge ID of the remote
bridge.ro OCTET STRING .1.3.6.1.4.1.97.8.9.1.1.3 |
kxtrunkRemoteIpThe IP address of the remote bridge, as reported by that
bridge for administrative purposes.ro IpAddress .1.3.6.1.4.1.97.8.9.1.1.4 |
kxtrunkLastErrorThe last reason for failure when the link is in closed,
oneway, or helddown state.ro Enumeration .1.3.6.1.4.1.97.8.9.1.1.5 |
kxtrunkLinkOrdinalThe position of this link within the trunk group.ro INTEGER .1.3.6.1.4.1.97.8.9.1.1.6 |
kxtrunkLinkCountThe number of links within the trunk group.ro INTEGER .1.3.6.1.4.1.97.8.9.1.1.7 |
kxtrunkLastChangeThe number of seconds since kxtrunkState changed.ro INTEGER .1.3.6.1.4.1.97.8.9.1.1.8 |
kxworkgroup OBJECT IDENTIFIER .1.3.6.1.4.1.97.8.10 |
kxWorkGroupNextNumberThe next available workgroup number to be used. When
creating a new workgroup, it is recommended to read
the value of the variable and use it to key into the
workgroup table.ro INTEGER .1.3.6.1.4.1.97.8.10.1 |
kxWorkGroupCurrentCountThe total number of workgroups currently defined.ro INTEGER .1.3.6.1.4.1.97.8.10.2 |
kxWorkGroupMaxCountThe maximum number of workgroups allowed.ro INTEGER .1.3.6.1.4.1.97.8.10.3 |
kxWorkGroupTableThis table contains work group definitions for the
interfaces. SEQUENCE OF KxWorkGroupEntry .1.3.6.1.4.1.97.8.10.4 |
kxWorkGroupEntryEach entry in this table contains a definition of a
work group. KxWorkGroupEntry .1.3.6.1.4.1.97.8.10.4.1 |
kxWorkGroupNumberAn integer that identifies the work group, used as an
index to this table.rw INTEGER .1.3.6.1.4.1.97.8.10.4.1.1 |
kxWorkGroupNameA 1-16 character work group name.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.97.8.10.4.1.2 |
kxWorkGroupPortsA list of all ports within the group. The first
octet specified ports 1-8, the second 9-16, etc.rw OCTET STRING .1.3.6.1.4.1.97.8.10.4.1.3 |
kxWorkGroupTypeThe type of work group: all - no additional
information needs to be supplied.rw Enumeration .1.3.6.1.4.1.97.8.10.4.1.4 |
kxtrapMgt OBJECT IDENTIFIER .1.3.6.1.4.1.97.8.11 |
kxtrapControlTableThis table contains information about the severity of
each trap and whether the trap is currently enabled. SEQUENCE OF KxtrapControlEntry .1.3.6.1.4.1.97.8.11.1 |
kxtrapControlEntry KxtrapControlEntry .1.3.6.1.4.1.97.8.11.1.1 |
kxtrapIndexThe specific trap number.ro INTEGER .1.3.6.1.4.1.97.8.11.1.1.1 |
kxtrapEnabledEnable or disable the generation of this trap.rw Enumeration .1.3.6.1.4.1.97.8.11.1.1.2 |
kxtrapSeverityA user-definable severity, indicating the importance
of the trap.rw Enumeration .1.3.6.1.4.1.97.8.11.1.1.3 |
kxtrapTextA description of the trap.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.97.8.11.1.1.4 |
kxtrapSeverityControlTableThis table contains information about whether a class
of traps of a particular severity is enabled or
disabled. SEQUENCE OF KxtrapSeverityControlEntry .1.3.6.1.4.1.97.8.11.2 |
kxtrapSeverityControlEntry KxtrapSeverityControlEntry .1.3.6.1.4.1.97.8.11.2.1 |
kxtrapSeverityControlSeverityA user-definable severity, indicating the importance
of the trap.rw Enumeration .1.3.6.1.4.1.97.8.11.2.1.1 |
kxtrapSeverityEnableEnable or disable all traps of a given severity
level.rw Enumeration .1.3.6.1.4.1.97.8.11.2.1.2 |
kxtrapIncludeTextWhether or not a formatted text string is included in
the trap PDU.rw Enumeration .1.3.6.1.4.1.97.8.11.3 |
kxtrapTimeThe time, in centiseconds, which should expire
between the sending of traps.rw TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.97.8.11.4 |
kxtrapRetryThe number of times any enterprise-specific trap is
to be sent for a given event. PDUs are retried using
a truncated exponential backoff: 2 seconds, 4 seconds,
8 seconds, 16 seconds, and then 32 seconds for all
succeeding intervals.rw INTEGER .1.3.6.1.4.1.97.8.11.5 |
kxtrapNumberThe number of traps that are in the kxtrapTable.ro INTEGER .1.3.6.1.4.1.97.8.11.6 |
kxtrapTableThis table contains the latest traps that have been
generated. SEQUENCE OF KxtrapEntry .1.3.6.1.4.1.97.8.11.7 |
kxtrapEntry KxtrapEntry .1.3.6.1.4.1.97.8.11.7.1 |
kxtrapEntryIndexA number representing the order in which the trap
occurred in time. This 32 bit number can wrap.ro INTEGER .1.3.6.1.4.1.97.8.11.7.1.1 |
kxtrapEntryTimeStampThe time at which the trap occurred.ro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.97.8.11.7.1.2 |
kxtrapEntryTextA description of the trap.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.97.8.11.7.1.3 |
kxtrapEntryNumberThe specific trap number, as specified in the TRAP
PDU.ro INTEGER .1.3.6.1.4.1.97.8.11.7.1.4 |
kxtrapEntrySeverityA user-definable severity, indicating the importance
of the trap.ro Enumeration .1.3.6.1.4.1.97.8.11.7.1.5 |
kxmirrorgroup OBJECT IDENTIFIER .1.3.6.1.4.1.97.8.12 |
kxmirrorModeTo turn off port mirroring, or turn on by specifying
rx, tx, or (rxandtx) which is the type of data to be
mirrored.rw Enumeration .1.3.6.1.4.1.97.8.12.1 |
kxmirrorDiagPortThis entry identifies the diagnostic port to which
mirrored packet will be destined.rw INTEGER .1.3.6.1.4.1.97.8.12.2 |
kxmirrorTargetPortListsAn octet string specifies the list of ports to be
mirrored. The first octet specifies ports 1-8 and
the second 9-16.rw OCTET STRING .1.3.6.1.4.1.97.8.12.3 |