CABLE-DIAG-MIB
AI MIB Summary
The CABLE-DIAG-MIB enables network devices to monitor the physical layer integrity and diagnostic status of attached copper Ethernet cables by exposing link fault detection metrics such as cable length, termination faults, and short/open circuit conditions. This module facilitates automated troubleshooting of physical connectivity issues by reporting specific cable quality parameters defined in IEEE 802.3 standards.
The MIB module for determining the status of the cables attached to the device
Main OID:
swCableDiagMIB.1.3.6.1.4.1.171.12.58
17
Objects
Active
Status
3
Dependencies
Imported Objects
Objects
17 total| Object Name |
|---|
swCableDiagMIBThe MIB module for determining the status of the cables attached to the device MODULE-IDENTITY .1.3.6.1.4.1.171.12.58 |
swCableDiagCtrl OBJECT IDENTIFIER .1.3.6.1.4.1.171.12.58.1 |
swEtherCableDiagTableA table that contains the cable situation for each port. SEQUENCE OF SwEtherCableDiagEntry .1.3.6.1.4.1.171.12.58.1.1 |
swEtherCableDiagEntryA list of cable situations for each port on the device. SwEtherCableDiagEntry .1.3.6.1.4.1.171.12.58.1.1.1 |
swEtherCableDiagPortIndexThis object indicates the module's port number.(1..Max port number in the module)ro INTEGER .1.3.6.1.4.1.171.12.58.1.1.1.1 |
swEtherCableDiagPortTypeIndicates the supported port data rate classification.ro Enumeration .1.3.6.1.4.1.171.12.58.1.1.1.2 |
swEtherCableDiagLinkStatusThis object indicates the link status.ro Enumeration .1.3.6.1.4.1.171.12.58.1.1.1.3 |
swEtherCableDiagPair1StatusThis object indicates the status of pair 1 of the cable.ro Enumeration .1.3.6.1.4.1.171.12.58.1.1.1.4 |
swEtherCableDiagPair2StatusThis object indicates the status of pair 2 of the cable.ro Enumeration .1.3.6.1.4.1.171.12.58.1.1.1.5 |
swEtherCableDiagPair3StatusThis object indicates the status of pair 3 of the cable.ro Enumeration .1.3.6.1.4.1.171.12.58.1.1.1.6 |
swEtherCableDiagPair4StatusThis object indicates the status of pair 4 of the cable.ro Enumeration .1.3.6.1.4.1.171.12.58.1.1.1.7 |
swEtherCableDiagPair1LengthThis object indicates the approx. length or length to the failure of pair 1 of the cable. This value is in meter units.ro INTEGER .1.3.6.1.4.1.171.12.58.1.1.1.8 |
swEtherCableDiagPair2LengthThis object indicates the approx. length or length to the failure of pair 2 of the cable. This value is in meter units.ro INTEGER .1.3.6.1.4.1.171.12.58.1.1.1.9 |
swEtherCableDiagPair3LengthThis object indicates the approx. length or length to the failure of pair 3 of the cable. This value is in meter units.ro INTEGER .1.3.6.1.4.1.171.12.58.1.1.1.10 |
swEtherCableDiagPair4LengthThis object indicates the approx. length or length to the failure of pair 4 of the cable. This value is in meter units.ro INTEGER .1.3.6.1.4.1.171.12.58.1.1.1.11 |
swEtherCableDiagActionFunction to run the cable diagnostic on selected port.rw Enumeration .1.3.6.1.4.1.171.12.58.1.1.1.12 |
swEtherCableDiagStatusIndicates the status of cable diagnostics on the port. not-run - cable diagnostics has never been run for this port processing - cable diagnostics is currently running on the port last-test-ok - the last cable diagnostics done on the port was successful last-test-failed - the last cable diagnostics done on the port failedro Enumeration .1.3.6.1.4.1.171.12.58.1.1.1.13 |