C-PRODUCT-QSIM-MIB
Detailed view of the defined objects, syntax rules, and hierarchical paths.
69
Objects
Active
Status
3
Dependencies
Imported Objects
Objects
69 total| Object Name |
|---|
qsimCard OBJECT IDENTIFIER .1.3.6.1.4.1.43.1.12.1.1.12.1 |
C-PRODUCT-BASE-MIB Unknown .1.3.6.1.4.1.43.1.12.1.1.12.1 |
qsimCardTableCard configuration table. SEQUENCE OF QsimCardEntry .1.3.6.1.4.1.43.1.12.1.1.12.1.1 |
qsimCardEntryCard configuration entry. QsimCardEntry .1.3.6.1.4.1.43.1.12.1.1.12.1.1.1 |
qsimCardMaxFrameSizeMaximum frame size for SDLC, DXI and Frame Relay frames.
WARNING: Change of the Maximum Frame Size will
cause Disruption of Service provided
by the card.rw Enumeration .1.3.6.1.4.1.43.1.12.1.1.12.1.1.1.1 |
qsimPort OBJECT IDENTIFIER .1.3.6.1.4.1.43.1.12.1.1.12.2 |
qsimPortTableQSIM port configuration table. SEQUENCE OF QsimPortEntry .1.3.6.1.4.1.43.1.12.1.1.12.2.1 |
qsimPortEntryQSIM port configuration entry. The slot number (portSlot)
of this card can be from 4 to 6. The port number (portNumber)
can be from 1 to 4. QsimPortEntry .1.3.6.1.4.1.43.1.12.1.1.12.2.1.1 |
qsimPortLinkTypeLink layer protocol supported by the port.rw Enumeration .1.3.6.1.4.1.43.1.12.1.1.12.2.1.1.1 |
qsimPortCableTypeType of cable connected to the port.ro Enumeration .1.3.6.1.4.1.43.1.12.1.1.12.2.1.1.2 |
qsimPortTermTimingSourceTerminal timing source. This object applies ONLY
when a DCE cable is connected to the port. If cable
type is 'none' or 'dce', this object can be read
and written. If cable type is 'dte', a get request
returns whatever value currently stored in the
managed node for this port and a set request returns
genErr.rw Enumeration .1.3.6.1.4.1.43.1.12.1.1.12.2.1.1.3 |
qsimPortReceiveTimingPhaseReceive timing phase control. This object applies ONLY
when a DCE cable is connected to the port. If cable
type is 'none' or 'dce', this object can be read and
written. If cable type is 'dte', a get request returns
whatever value currently stored in the managed node for
this port and a set request returns genErr.rw Enumeration .1.3.6.1.4.1.43.1.12.1.1.12.2.1.1.4 |
qsimPortDataRateData rate supported by the port.rw Enumeration .1.3.6.1.4.1.43.1.12.1.1.12.2.1.1.5 |
qsimPortMinFlagBytesMinimum flag bytes required to distinguish a frame.rw Enumeration .1.3.6.1.4.1.43.1.12.1.1.12.2.1.1.6 |
qsimPortFcsSizeNumber of bytes in the FCS field of a frame.rw Enumeration .1.3.6.1.4.1.43.1.12.1.1.12.2.1.1.7 |
qsimPortRtsRTS pin status.ro PinStatus .1.3.6.1.4.1.43.1.12.1.1.12.2.1.1.8 |
qsimPortCtsCTS pin status.ro PinStatus .1.3.6.1.4.1.43.1.12.1.1.12.2.1.1.9 |
qsimPortDcdDCD pin status.ro PinStatus .1.3.6.1.4.1.43.1.12.1.1.12.2.1.1.10 |
qsimPortDsrDSR pin status.ro PinStatus .1.3.6.1.4.1.43.1.12.1.1.12.2.1.1.11 |
hsimPort OBJECT IDENTIFIER .1.3.6.1.4.1.43.1.12.1.1.12.3 |
hsimPortTableHSIM port configuration table. SEQUENCE OF HsimPortEntry .1.3.6.1.4.1.43.1.12.1.1.12.3.1 |
hsimPortEntryHSIM port configuration entry. The slot number (portSlot)
of this card can be from 4 to 6. The port number (portNumber)
of this card is always 1. HsimPortEntry .1.3.6.1.4.1.43.1.12.1.1.12.3.1.1 |
hsimPortLinkTypeLink layer protocol supported by the port.rw Enumeration .1.3.6.1.4.1.43.1.12.1.1.12.3.1.1.1 |
hsimPortDceDteModeDCE/DTE mode of the port.rw Enumeration .1.3.6.1.4.1.43.1.12.1.1.12.3.1.1.2 |
hsimPortDataRateData rate supported by the port.ro Enumeration .1.3.6.1.4.1.43.1.12.1.1.12.3.1.1.3 |
hsimPortMinFlagBytesMinimum flag bytes required to distinguish a frame.rw Enumeration .1.3.6.1.4.1.43.1.12.1.1.12.3.1.1.4 |
hsimPortFcsSizeNumber of bytes in the FCS field of a frame.rw Enumeration .1.3.6.1.4.1.43.1.12.1.1.12.3.1.1.5 |
hsimPortTaTA pin status.ro PinStatus .1.3.6.1.4.1.43.1.12.1.1.12.3.1.1.6 |
hsimPortCaCA pin status.ro PinStatus .1.3.6.1.4.1.43.1.12.1.1.12.3.1.1.7 |
qsimVc OBJECT IDENTIFIER .1.3.6.1.4.1.43.1.12.1.1.12.4 |
qsimSdlcVc OBJECT IDENTIFIER .1.3.6.1.4.1.43.1.12.1.1.12.4.1 |
qsimDxiVc OBJECT IDENTIFIER .1.3.6.1.4.1.43.1.12.1.1.12.4.2 |
qsimFrameRelayVc OBJECT IDENTIFIER .1.3.6.1.4.1.43.1.12.1.1.12.4.3 |
qsimLmi OBJECT IDENTIFIER .1.3.6.1.4.1.43.1.12.1.1.12.6 |
qsimLmiTableLMI configuration table. SEQUENCE OF QsimLmiEntry .1.3.6.1.4.1.43.1.12.1.1.12.6.1 |
qsimLmiEntryLMI configuration entry. The slot number (portSlot)
should be from 4 to 6. The port number (portNumber)
is from 1 to 4 for QSIM card, 1 to 8 for FAM card, and
1 for HSIM card. QsimLmiEntry .1.3.6.1.4.1.43.1.12.1.1.12.6.1.1 |
qsimLmiProtocolLMI protocol supported by the port.rw Enumeration .1.3.6.1.4.1.43.1.12.1.1.12.6.1.1.1 |
qsimLmiProcedureLMI procedure supported by the port. This object applies
when LMI Q.933 Annex A or T1.617 Annex D protocol is selected.rw Enumeration .1.3.6.1.4.1.43.1.12.1.1.12.6.1.1.2 |
qsimLmiUserT391User-side link integrity verification (LIV) polling timer. This
object applies when LMI user-side or bidirectional procedure
is selected.rw INTEGER .1.3.6.1.4.1.43.1.12.1.1.12.6.1.1.3 |
qsimLmiUserN391User-side full status polling counter. This object applies
when LMI user-side or bidirectional procedure is selected.rw INTEGER .1.3.6.1.4.1.43.1.12.1.1.12.6.1.1.4 |
qsimLmiUserN392User-side error threshold. This object applies when
LMI user-side or bidirectional procedure is selected.
User-side N392 should be less than or equal to user-
side N393.rw INTEGER .1.3.6.1.4.1.43.1.12.1.1.12.6.1.1.5 |
qsimLmiUserN393User-side monitored events count. This object applies when
LMI user-side or bidirectional procedure is selected.rw INTEGER .1.3.6.1.4.1.43.1.12.1.1.12.6.1.1.6 |
qsimLmiNetworkT392Network-side polling verification timer. This object applies
when LMI network-side or bidirectional procedure is selected.rw INTEGER .1.3.6.1.4.1.43.1.12.1.1.12.6.1.1.7 |
qsimLmiNetworkN392Network-side error threshold. This object applies when
LMI network-side or bidirectional procedure is selected.
Network-side N392 should be less than or equal to Network-
side N393.rw INTEGER .1.3.6.1.4.1.43.1.12.1.1.12.6.1.1.8 |
qsimLmiNetworkN393Network-side monitored events count. This object applies
when LMI network-side or bidirectional procedure is selected.rw INTEGER .1.3.6.1.4.1.43.1.12.1.1.12.6.1.1.9 |
qsimNewVc OBJECT IDENTIFIER .1.3.6.1.4.1.43.1.12.1.1.12.9 |
qsimNewSdlcVc OBJECT IDENTIFIER .1.3.6.1.4.1.43.1.12.1.1.12.9.1 |
qsimNewSdlcVcTableSDLC VC configuration table. SEQUENCE OF QsimNewSdlcVcEntry .1.3.6.1.4.1.43.1.12.1.1.12.9.1.1 |
qsimNewSdlcVcEntrySDLC VC configuration entry. The slot number (vcPortSlot)
of the VC can be from 4 to maxslots. The port number (vcPortPort)
can be from 1 to 4. QsimNewSdlcVcEntry .1.3.6.1.4.1.43.1.12.1.1.12.9.1.1.1 |
qsimNewSdlcVcShapperData rate supported by the SDLC VC. Depending on the type
of card a VC is configured, the shapper numbers are assigned
as follows:
HSIM QSIM
data rate data rate shapper number
- -
1.5m 64k 1
3m 128k 2
4.5m 192k 3
6m 256k 4
7.5m 384k 5
9m 512k 6
10.5m 640k 7
12m 768k 8
13.5m 1m 9
15m 1.5m 10
16.5m 2m 11
18m 4m 12
20m 8m 13rw INTEGER .1.3.6.1.4.1.43.1.12.1.1.12.9.1.1.1.1 |
qsimNewDxiVc OBJECT IDENTIFIER .1.3.6.1.4.1.43.1.12.1.1.12.9.2 |
qsimNewDxiVcTableDXI VC configuration table. SEQUENCE OF QsimNewDxiVcEntry .1.3.6.1.4.1.43.1.12.1.1.12.9.2.1 |
qsimNewDxiVcEntryDXI VC configuration entry. The slot number (vcPortSlot)
of the VC can be from 4 to 6. The port number (vcPortPort)
can be from 1 to 4. QsimNewDxiVcEntry .1.3.6.1.4.1.43.1.12.1.1.12.9.2.1.1 |
qsimNewDxiVcDfaVpiDXI DFA VPI.rw INTEGER .1.3.6.1.4.1.43.1.12.1.1.12.9.2.1.1.1 |
qsimNewDxiVcDfaVciDXI DFA VCI.rw INTEGER .1.3.6.1.4.1.43.1.12.1.1.12.9.2.1.1.2 |
qsimNewDxiVcDfaVciRangeDXI VCI range. This object is used to create a set
of VCs whose VPI equals to the value of the instance
of qsimDxiVcDfaVpi and whose VCIs are in the range
FROM 'the value of the instance of qsimDxiVcDfaVci'
TO 'the value of the instance of this object PLUS the
value of the instance of qsiDxiVcDfaVci MINUS 1'. A
successful set request will generate 1 to N VC entries
in this table. Where N equals to the value of the
instance of this object. A get request always returns
1.rw INTEGER .1.3.6.1.4.1.43.1.12.1.1.12.9.2.1.1.3 |
qsimNewDxiVcShapperData rate supported by the DXI VC. Depending on the type
of card a VC is configured, the shapper numbers are assigned
as follows:
HSIM QSIM
data rate data rate shapper number
- -
1.5m 64k 1
3m 128k 2
4.5m 192k 3
6m 256k 4
7.5m 384k 5
9m 512k 6
10.5m 640k 7
12m 768k 8
13.5m 1m 9
15m 1.5m 10
16.5m 2m 11
18m 4m 12
20m 8m 13rw INTEGER .1.3.6.1.4.1.43.1.12.1.1.12.9.2.1.1.4 |
qsimNewFrameRelayVc OBJECT IDENTIFIER .1.3.6.1.4.1.43.1.12.1.1.12.9.3 |
qsimNewFrameRelayVcTableFrame relay VC configuration table. SEQUENCE OF QsimNewFrameRelayVcEntry .1.3.6.1.4.1.43.1.12.1.1.12.9.3.1 |
qsimNewFrameRelayVcEntryFrame relay VC configuration entry. The slot number
(vcPortSlot) of the VC can be from 4 to maxslots. The port
number (vcPortPort) can be from 1 to 4. QsimNewFrameRelayVcEntry .1.3.6.1.4.1.43.1.12.1.1.12.9.3.1.1 |
qsimNewFrameRelayVcInterworkingFrame Relay/ATM interworking mode.rw Enumeration .1.3.6.1.4.1.43.1.12.1.1.12.9.3.1.1.1 |
qsimNewFrameRelayVcEncapsulationEncapsulation type. This object applies ONLY to service
interworking.rw Enumeration .1.3.6.1.4.1.43.1.12.1.1.12.9.3.1.1.2 |
qsimNewFrameRelayVcDe2ClpIf mode 1 mapping is desirable, the user shall select
direct mapping. If mode 2 mapping is desirable, the
user shall select always-0 or always-1 to map the CLP
field to a constant value (0 or 1).rw Enumeration .1.3.6.1.4.1.43.1.12.1.1.12.9.3.1.1.3 |
qsimNewFrameRelayVcClp2DeFor network interworking -
The options are none and direct. If mode 1 mapping
is desirable, the user shall select direct mapping.
If mode 2 mapping is desirable, the user shall select
none. The none option maps the DE field in FR-SSCS
PDU to the core-Q.922 frame DE field and ignores the
CLP field in the ATM cells.
For service interworking -
The options are direct, always-0 and always-1. If mode
1 mapping is desirable, the user shall select direct
mapping. If mode 2 mapping is desirable, the user shall
select always-0 or always-1 to map the DE field to a
constant value (0 or 1).rw Enumeration .1.3.6.1.4.1.43.1.12.1.1.12.9.3.1.1.4 |
qsimNewFrameRelayVcFecnToEfciThis object applies ONLY to service interworking. If
mode 1 mapping is desirable, direct mapping should be
selected. If mode 2 mapping is desirable, always-0
should be selected to set the EFCI field to 'congestion
not experienced'.rw Enumeration .1.3.6.1.4.1.43.1.12.1.1.12.9.3.1.1.5 |
qsimNewFrameRelayVcShapperData rate supported by the frame relay VC. Depending on the type
of card a VC is configured, the shapper numbers are assigned
as follows:
HSIM QSIM
data rate data rate shapper number
- -
1.5m 64k 1
3m 128k 2
4.5m 192k 3
6m 256k 4
7.5m 384k 5
9m 512k 6
10.5m 640k 7
12m 768k 8
13.5m 1m 9
15m 1.5m 10
16.5m 2m 11
18m 4m 12
20m 8m 13rw INTEGER .1.3.6.1.4.1.43.1.12.1.1.12.9.3.1.1.6 |
qsimNewFrameRelayVcDlciFrame relay DLCI.rw INTEGER .1.3.6.1.4.1.43.1.12.1.1.12.9.3.1.1.7 |
qsimNewFrameRelayVcFrSscsDlciThis object applies ONLY to network interworking.
Its valid value is 16..991 and 1022.rw INTEGER .1.3.6.1.4.1.43.1.12.1.1.12.9.3.1.1.8 |
qsimNewFrameRelayVcStatusFrame relay PVC operational status.ro Enumeration .1.3.6.1.4.1.43.1.12.1.1.12.9.3.1.1.9 |