ALCATEL-IND1-PORT-MIB
AI MIB Summary
The ALCATEL-IND1-PORT-MIB provides enterprise-specific SNMP management for Alcatel-Lucent Ethernet and Fiber Channel switching modules, exposing configuration parameters and operational states for physical and logical port interfaces. It enables administrators to monitor port status, speed, duplex settings, and error counters to facilitate precise troubleshooting and configuration of Layer 2 switching hardware.
This module describes an authoritative enterprise-specific Simple Network Management Protocol (SNMP) Management Information Base (MIB):
This group contains the configuration information data for the Ethernet and Fiber Channel Switching Module.
The right to make changes in specification and other information contained in this document without prior notice is reserved.
No liability shall be assumed for any incidental, indirect, special, or consequential damages whatsoever arising from or related to this document or the information contained herein.
Vendors, end-users, and other interested parties are granted non-exclusive license to use this specification in connection with management of the products for which it is intended to be used.
Copyright (C) 1995-2013 Alcatel-Lucent ALL RIGHTS RESERVED WORLDWIDE
Main OID:
alcatelIND1PortMIB.1.3.6.1.4.1.6486.801.1.2.1.5.1
230
Objects
Active
Status
6
Dependencies
Imported Objects
Objects
230 total| Object Name |
|---|
alcatelIND1PortMIBThis module describes an authoritative enterprise-specific Simple
Network Management Protocol (SNMP) Management Information Base (MIB):
This group contains the configuration information data
for the Ethernet and Fiber Channel Switching Module.
The right to make changes in specification and other information
contained in this document without prior notice is reserved.
No liability shall be assumed for any incidental, indirect, special, or
consequential damages whatsoever arising from or related to this
document or the information contained herein.
Vendors, end-users, and other interested parties are granted
non-exclusive license to use this specification in connection with
management of the products for which it is intended to be used.
Copyright (C) 1995-2013 Alcatel-Lucent
ALL RIGHTS RESERVED WORLDWIDE MODULE-IDENTITY .1.3.6.1.4.1.6486.801.1.2.1.5.1 |
IMPORTSThis module describes an authoritative enterprise-specific Simple
Network Management Protocol (SNMP) Management Information Base (MIB):
This group contains the configuration information data
for the Ethernet and Fiber Channel Switching Module.
The right to make changes in specification and other information
contained in this document without prior notice is reserved.
No liability shall be assumed for any incidental, indirect, special, or
consequential damages whatsoever arising from or related to this
document or the information contained herein.
Vendors, end-users, and other interested parties are granted
non-exclusive license to use this specification in connection with
management of the products for which it is intended to be used.
Copyright (C) 1995-2013 Alcatel-Lucent
ALL RIGHTS RESERVED WORLDWIDE Unknown .1.3.6.1.4.1.6486.801.1.2.1.5.1 |
alcatelIND1PortNotifications OBJECT IDENTIFIER .1.3.6.1.4.1.6486.801.1.2.1.5.1.0 |
esmDrvTrapDropsLinkWhen the Ethernet code drops the link because of
excessive errors, a Trap is sent. NOTIFICATION-TYPE .1.3.6.1.4.1.6486.801.1.2.1.5.1.0.1 |
ddmTemperatureThresholdViolatedThis object notifies management station if an SFP/XFP/SFP+ temperature has crossed any
threshold or reverted from previous threshold violation for a port represented by ifIndex.
It also provides the current realtime value of SFP/XFP/SFP+ temperature. NOTIFICATION-TYPE .1.3.6.1.4.1.6486.801.1.2.1.5.1.0.2 |
ddmVoltageThresholdViolatedThis object notifies management station if an SFP/XFP/SFP+ supply voltage has crossed any
threshold or reverted from previous threshold violation for a port represented by ifIndex.
It also provides the current realtime value of SFP/XFP/SFP+ supply voltage. NOTIFICATION-TYPE .1.3.6.1.4.1.6486.801.1.2.1.5.1.0.3 |
ddmCurrentThresholdViolatedThis object notifies management station if an SFP/XFP/SFP+ Tx bias current has crossed any
threshold or reverted from previous threshold violation for a port represented by ifIndex.
It also provides the current realtime value of SFP/XFP/SFP+ Tx bias current. NOTIFICATION-TYPE .1.3.6.1.4.1.6486.801.1.2.1.5.1.0.4 |
ddmTxPowerThresholdViolatedThis object notifies management station if an SFP/XFP/SFP+ Tx output power has crossed any
threshold or reverted from previous threshold violation for a port represented by ifIndex.
It also provides the current realtime value of SFP/XFP/SFP+ Tx output power. NOTIFICATION-TYPE .1.3.6.1.4.1.6486.801.1.2.1.5.1.0.5 |
ddmRxPowerThresholdViolatedThis object notifies management station if an SFP/XFP/SFP+ Rx optical power has crossed any
threshold or reverted from previous threshold violation for a port represented by ifIndex.
It also provides the current realtime value of SFP/XFP/SFP+ Rx optical power. NOTIFICATION-TYPE .1.3.6.1.4.1.6486.801.1.2.1.5.1.0.6 |
portViolationTrapA Trap will be generated when a port violation occurs. The port
violation trap will indicate the source of the violation and the
reason for the violation. NOTIFICATION-TYPE .1.3.6.1.4.1.6486.801.1.2.1.5.1.0.7 |
portViolationNotificationTrapA Trap will be generated when a port violation is cleared. NOTIFICATION-TYPE .1.3.6.1.4.1.6486.801.1.2.1.5.1.0.8 |
alaDyingGaspTrapDying Gasp trap. NOTIFICATION-TYPE .1.3.6.1.4.1.6486.801.1.2.1.5.1.0.9 |
alcatelIND1PortMIBObjects OBJECT IDENTIFIER .1.3.6.1.4.1.6486.801.1.2.1.5.1.1 |
esmConfTrap OBJECT IDENTIFIER .1.3.6.1.4.1.6486.801.1.2.1.5.1.1.1 |
esmDrvTrapDropsPartitioned port (separated due to errors).ro Integer32 .1.3.6.1.4.1.6486.801.1.2.1.5.1.1.1.1 |
physicalPort OBJECT IDENTIFIER .1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2 |
esmConfTableA list of ESM Physical Port instances. SEQUENCE OF EsmConfEntry .1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.1 |
esmConfEntryA ESM Physical Port entry. EsmConfEntry .1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.1.1 |
esmPortSlotThe physical Slot number for this Ethernet Port.
Slot number has been added to be used by the private Trap.ro Integer32 .1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.1.1.1 |
esmPortIFThe on-board interface number for this Ethernet Port.
Port Number has been added to be used by the private Trap.ro Integer32 .1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.1.1.2 |
esmPortAutoSpeedThe automatically detected port line speed
of this ESM port.ro Enumeration .1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.1.1.3 |
esmPortAutoDuplexModeThe automatically detected port duplex mode
of this ESM port.
Note: GigaEthernet supports only Full duplex mode.
Default value for 10/100 = Half duplex mode.ro Enumeration .1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.1.1.4 |
esmPortCfgSpeedThe configured port line speed of this ESM port.rw Enumeration .1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.1.1.5 |
esmPortCfgDuplexModeThe configured port duplex mode of this ESM port.
Note: GigaEthernet support only full-duplex.rw Enumeration .1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.1.1.6 |
esmPortAdminStatusThe desired state of the interface. The testing(3) state
indicates that no operational packets can be passed. When a
managed system initializes, all interfaces start with
ifAdminStatus in the down(2) state. As a result of either
explicit management action or per configuration information
retained by the managed system, ifAdminStatus is then
changed to either the up(1) or testing(3) states (or remains
in the down(2) state).rw Enumeration .1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.1.1.7 |
esmPortLinkUpDownTrapEnableIndicates whether linkUp/linkDown traps should be generated
for this interface.
By default, this object should have the value enable(1) for
interfaces which do not operate on 'top' of any other
interface (as defined in the ifStackTable), and disable(2)
otherwise.rw Enumeration .1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.1.1.8 |
esmPortCfgMaxFrameSizeConfigure the value of the maximum frame
size allow.
For 10Mbps the range is upto 1518 bytes.
For ports with speed > 10Mbps the value can extend upto 9216 bytes.rw Integer32 .1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.1.1.11 |
esmPortAliasThis object is an 'alias' name for the interface as
specified by a network manager, and provides a non-volatile
'handle' for the interface.
On the first instantiation of an interface, the value of
ifAlias associated with that interface is the zero-length
string. As and when a value is written into an instance of
ifAlias through a network management set operation, then the
agent must retain the supplied value in the ifAlias instance
associated with the same interface for as long as that
interface remains instantiated, including across all re-
initializations/reboots of the network management system,
including those which result in a change of the interface's
ifIndex value.
An example of the value which a network manager might store
in this object for a WAN interface is the (Telco's) circuit
number/identifier of the interface.
Some agents may support write-access only for interfaces
having particular values of ifType. An agent which supports
write access to this object is required to keep the value in
non-volatile storage, but it may limit the length of new
values depending on how much storage is already occupied by
the current values for other interfaces.rw SnmpAdminString .1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.1.1.12 |
esmPortCfgPauseThis object is used to configure the default
administrative PAUSE mode for this interface.
This object represents the
administratively-configured PAUSE mode for this
interface. If auto-negotiation is not enabled
or is not implemented for the active MAU
attached to this interface, the value of this
object determines the operational PAUSE mode
of the interface whenever it is operating in
full-duplex mode. In this case, a set to this
object will force the interface into the
specified mode.
If auto-negotiation is implemented and enabled
for the MAU attached to this interface, the
PAUSE mode for this interface is determined by
auto-negotiation, and the value of this object
denotes the mode to which the interface will
automatically revert if/when auto-negotiation is
later disabled. For more information on what
pause values will be autonegotiated based on
settings on this object, please refer to the
truth table in the users manual.
Note that the value of this object is ignored
when the interface is not operating in
full-duplex mode.rw Enumeration .1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.1.1.13 |
esmPortCfgAutoNegotiationAllow the user to enable or disable the port auto negotiation.rw Enumeration .1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.1.1.15 |
esmPortCfgCrossoverAllow the user to configure port crossover.
This object is applicable only to copper ports.
For fiber ports notapplicable is returned as a status.rw Enumeration .1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.1.1.16 |
esmPortCfgHybridActiveTypeThis object is only applicable to hybrid ports .
It indicates configured active media type.(the operational media
type may be different if esmPortCfgHybridMode is configured to be
preferredFiber or preferredCopper)
For non hybrid ports notapplicable is returned as a status.ro Enumeration .1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.1.1.18 |
esmPortCfgHybridModeThis object is only applicable to hybrid ports.
This allows the user the user to configure the media type
with which the port should come up.
The user can configure the port to come as copper only
or fiber only or either fiber/copper
(with preference to one of them).rw Enumeration .1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.1.1.19 |
esmPortOperationalHybridTypeThis object is only applicable to hybrid ports .
It indicates the actual media type that has link up and is or will be
passing traffic. If link is not present the object will return none(0) value.ro Enumeration .1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.1.1.20 |
esmPortBcastRateLimitEnableEnable/disable per port broadcast traffic rate limit. When 'enable' value from
esmPortBcastRateLimit object will be applicable to the ingressing broadcast traffic if
the speed is greater than the limit else the default limit for the speed will be
applied. When it is 'disable' no limit is applied to incoming broadcast traffic which
is limited by the port speed.rw Enumeration .1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.1.1.21 |
esmPortBcastRateLimitTypeThe unit applicable to the value in esmPortBcastRateLimit object.rw Enumeration .1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.1.1.22 |
esmPortBcastRateLimitThe value of the maximum broadcast traffic that can flow
through the port. The actual value depends on the port speed
if the configured values is greater than the current port speed.rw Integer32 .1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.1.1.23 |
esmPortMcastRateLimitEnableEnable/disable per port multicast traffic rate limit. When 'enable' value from
esmPortMcastRateLimit object will be applicable to the ingressing multicast traffic if
the speed is greater than the limit else the default limit for the speed will be
applied. When it is 'disable' no limit is applied to incoming multicast traffic which
is limited by the port speed.rw Enumeration .1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.1.1.24 |
esmPortMcastRateLimitTypeThe unit applicable to the value in esmPortMcastRateLimit object.rw Enumeration .1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.1.1.25 |
esmPortMcastRateLimitThe value of the maximum multicast traffic that can flow
through the port. The actual value depends on the port speed
if the configured values is greater than the current port speed.rw Integer32 .1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.1.1.26 |
esmPortUucastRateLimitEnableEnable/disable per port unknown unicast traffic rate limit. When 'enable' value from
esmPortUucastRateLimit object will be applicable to the ingressing unknown unicast traffic if
the speed is greater than the limit else the default limit for the speed will be
applied. When it is 'disable' no limit is applied to incoming unknown unicast traffic which
is limited by the port speed.rw Enumeration .1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.1.1.27 |
esmPortUucastRateLimitTypeThe unit applicable to the value in esmPortUucastRate object.rw Enumeration .1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.1.1.28 |
esmPortUucastRateLimitThe value of the maximum unknown unicast traffic that can flow
through the port. The actual value depends on the port speed
if the configured values is greater than the current port speed.rw Integer32 .1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.1.1.29 |
esmPortIngressRateLimitEnableEnable/disable per port ingress traffic rate limit. When 'enable' value from
esmPortIngressRate object will be applicable to the ingressing traffic (BC, MC, UUC) if
the speed is greater than the limit else the default limit for the speed will be
applied. When it is 'disable' no limit is applied to incoming traffic which
is limited by the port speed.rw Enumeration .1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.1.1.30 |
esmPortIngressRateLimitThe value of the maximum ingress traffic that can flow
through the port. The actual value depends on the port speed
if the configured value is greater than the current port speed.rw Integer32 .1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.1.1.31 |
esmPortIngressRateLimitBurstThe value of ingress traffic burst size in Mbits.rw Integer32 .1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.1.1.32 |
esmPortEPPEnableuse for port diagnosticsrw Enumeration .1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.1.1.33 |
esmPortEEEEnable10Gbase-T Energy Efficent Ethernet port parameter.rw Enumeration .1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.1.1.34 |
esmPortIsFiberChannelCapableThe port can be configured as Fiber Channel interface (yes) or can
not be configured as Fiber Channel interface.rw Enumeration .1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.1.1.35 |
alcetherStatsTableA list of Ethernet statistics entries. SEQUENCE OF AlcetherStatsEntry .1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.2 |
alcetherStatsEntryA collection of statistics kept for a particular
Ethernet interface. As an example, an instance of the
etherStatsPkts object might be named alcetherStatsPkts.1 AlcetherStatsEntry .1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.2.1 |
alcetherClearStatsUsed to Clear all Statistics counters.
By default, this object contains zero value.rw Enumeration .1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.2.1.1 |
alcetherLastClearStatsThe value of SysUpTime at the time of all
the statistics counters are cleared.
By default, this object contains a zero value.ro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.2.1.2 |
alcetherStatsCRCAlignErrorsThe total number of packets received that
had a length (excluding framing bits, but
including FCS octets) of between 64 and 1518
octets, inclusive, but but had either a bad
Frame Check Sequence (FCS) with an integral
number of octets (FCS Error) or a bad FCS with
a non-integral number of octets (Alignment Error).ro Counter64 .1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.2.1.3 |
alcetherStatsRxUndersizePktsThe total number of packets received that were
less than 64 octets long (excluding framing bits,
but including FCS octets) and were otherwise well
formed.ro Counter64 .1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.2.1.4 |
alcetherStatsTxUndersizePktsThe total number of packets transmitted that were
less than 64 octets long (excluding framing bits,
but including FCS octets) and were otherwise well
formed.ro Counter64 .1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.2.1.5 |
alcetherStatsTxOversizePktsThe total number of packets transmitted that were
longer than 1518 octets long (excluding framing bits,
but including FCS octets) and were otherwise well
formed.ro Counter64 .1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.2.1.6 |
alcetherStatsRxJabbersThe total number of packets received that were
longer than 1518 octets (excluding framing bits,
but including FCS octets), and had either a bad
Frame Check Sequence (FCS) with an integral number
of octets (FCS Error) or a bad FCS with a
non-integral number of octets (Alignment Error).
Note that this definition of jabber is different
than the definition in IEEE-802.3 section 8.2.1.5
(10BASE5) and section 10.3.1.4 (10BASE2). These
documents define jabber as the condition where any
packet exceeds 20 ms. The allowed range to detect
jabber is between 20 ms and 150 ms.ro Counter64 .1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.2.1.7 |
alcetherStatsRxCollisionsThe best estimate of the total number of collisions
on this Ethernet segment (in reception).
Only for Ethernet Interfaces.
The value returned will depend on the location of
the RMON probe. Section 8.2.1.3 (10BASE-5) and
section 10.3.1.3 (10BASE-2) of IEEE standard 802.3
states that a station must detect a collision, in
the receive mode, if three or more stations are
transmitting simultaneously. A repeater port must
detect a collision when two or more stations are
transmitting simultaneously. Thus a probe placed on
a repeater port could record more collisions than a
probe connected to a station on the same segment
would.
Probe location plays a much smaller role when
considering 10BASE-T. 14.2.1.4 (10BASE-T) of IEEE
standard 802.3 defines a collision as the
simultaneous presence of signals on the DO and RD
circuits (transmitting and receiving at the same
time). A 10BASE-T station can only detect
collisions when it is transmitting. Thus probes
placed on a station and a repeater, should report
the same number of collisions.
Note also that an RMON probe inside a repeater
should ideally report collisions between the
repeater and one or more other hosts (transmit
collisions as defined by IEEE 802.3k) plus receiver
collisions observed on any coax segments to which
the repeater is connected.ro Counter64 .1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.2.1.8 |
alcetherStatsTxCollisionsThe best estimate of the total number of collisions
on this Ethernet segment (in transmition).
Only for Ethernet Interfaces.
The value returned will depend on the location of
the RMON probe. Section 8.2.1.3 (10BASE-5) and
section 10.3.1.3 (10BASE-2) of IEEE standard 802.3
states that a station must detect a collision, in
the receive mode, if three or more stations are
transmitting simultaneously. A repeater port must
detect a collision when two or more stations are
transmitting simultaneously. Thus a probe placed on
a repeater port could record more collisions than a
probe connected to a station on the same segment
would.
Probe location plays a much smaller role when
considering 10BASE-T. 14.2.1.4 (10BASE-T) of IEEE
standard 802.3 defines a collision as the
simultaneous presence of signals on the DO and RD
circuits (transmitting and receiving at the same
time). A 10BASE-T station can only detect
collisions when it is transmitting. Thus probes
placed on a station and a repeater, should report
the same number of collisions.
Note also that an RMON probe inside a repeater
should ideally report collisions between the
repeater and one or more other hosts (transmit
collisions as defined by IEEE 802.3k) plus receiver
collisions observed on any coax segments to which
the repeater is connected.ro Counter64 .1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.2.1.9 |
alcetherStatsPkts64OctetsThe total number of packets (including bad
packets) received that were 64 octets in length
(excluding framing bits but including FCS octets).ro Counter64 .1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.2.1.10 |
alcetherStatsPkts65to127OctetsThe total number of packets (including bad
packets) received that were between
65 and 127 octets in length inclusive
(excluding framing bits but including FCS octets).ro Counter64 .1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.2.1.11 |
alcetherStatsPkts128to255OctetsThe total number of packets (including bad
packets) received that were between
128 and 255 octets in length inclusive
(excluding framing bits but including FCS octets).ro Counter64 .1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.2.1.12 |
alcetherStatsPkts256to511OctetsThe total number of packets (including bad
packets) received that were between
256 and 511 octets in length inclusive
(excluding framing bits but including FCS octets).ro Counter64 .1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.2.1.13 |
alcetherStatsPkts512to1023OctetsThe total number of packets (including bad
packets) received that were between
512 and 1023 octets in length inclusive
(excluding framing bits but including FCS octets).ro Counter64 .1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.2.1.14 |
alcetherStatsPkts1024to1518OctetsThe total number of packets (including bad
packets) received that were between
1024 and 1518 octets in length inclusive
(excluding framing bits but including FCS octets).
For both Ethernet and GigaEthernet.ro Counter64 .1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.2.1.15 |
gigaEtherStatsPkts1519to4095OctetsThe total number of packets (including bad
packets) received that were between
1519 and 4095 octets in length inclusive
(excluding framing bits but including FCS octets).
Only for GigaEthernet interfacesro Counter64 .1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.2.1.16 |
gigaEtherStatsPkts4096to9215OctetsThe total number of packets (including bad
packets) received that were between
4096 and 9215 octets in length inclusive
(excluding framing bits but including FCS octets).
Only for GigaEthernet interfacesro Counter64 .1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.2.1.17 |
alcetherStatsPkts1519to2047OctetsThe total number of frames(including error packets) received
that were between 1519 and 2047 bytes in length inclusive
(excluding framing bits but including FCS bytes).ro Counter64 .1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.2.1.18 |
alcetherStatsPkts2048to4095OctetsThe total number of frames(including error packets) received
that were between 2048 and 4095 bytes in length inclusive
(excluding framing bits but including FCS bytes).ro Counter64 .1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.2.1.19 |
alcetherStatsPkts4096OctetsThe total number of frames(including error packets) received
that were greater than or equal to 4096 bytes in length inclusive
(excluding framing bits but including FCS bytes).ro Counter64 .1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.2.1.20 |
alcetherStatsRxGiantPktsThe total number of frames that are greater than the specified
Max length value, with a valid CRC, dropped because too long.ro Counter64 .1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.2.1.21 |
alcetherStatsRxDribbleNibblePktsThe total number of frames for which a dribble nibble has been
received and CRC is correct.ro Counter64 .1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.2.1.22 |
alcetherStatsRxLongEventPktsThe total number of frames for which the Carrier sense exceeds
50000 bit times for 10 Mbits/sec or 80000 bit times for
100 Mbits/sec.ro Counter64 .1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.2.1.23 |
alcetherStatsRxVlanTagPktsThe total number of frames for which Type/Length field
contains the VLAN protocol identifier (0x8100).ro Counter64 .1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.2.1.24 |
alcetherStatsRxControlPktsThe total number of frames that were recognized as control frames.ro Counter64 .1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.2.1.25 |
alcetherStatsRxLenChkErrPktsThe total number of frames for which the frame length field value
in the Type/Length field does not match the actual data bytes
length and is NOT a type field.ro Counter64 .1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.2.1.26 |
alcetherStatsRxCodeErrPktsThe total number of frames for which one or more nibbles were
signaled as errors during reception of the frame.ro Counter64 .1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.2.1.27 |
alcetherStatsRxDvEventPktsThe total number of frames for which a RX_DV event (packet not
too long enough to be valid packet) has been seen before the
correct frame.ro Counter64 .1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.2.1.28 |
alcetherStatsRxPrevPktDroppedThe total number of frames for which a packet has been dropped
(because of too small IFG) before the correct frame.ro Counter64 .1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.2.1.29 |
alcetherStatsTx64OctetsThe total number of transmitted frames of 64 bytes.ro Counter64 .1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.2.1.30 |
alcetherStatsTx65to127OctetsThe total number of transmitted frames that were between
65 and 127 bytes in length inclusive (excluding framing bits
but including FCS bytes).ro Counter64 .1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.2.1.31 |
alcetherStatsTx128to255OctetsThe total number of transmitted frames that were between
128 and 255 bytes in length inclusive (excluding framing bits
but including FCS bytes).ro Counter64 .1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.2.1.32 |
alcetherStatsTx256to511OctetsThe total number of transmitted frames that were between
256 and 511 bytes in length inclusive (excluding framing bits
but including FCS bytes).ro Counter64 .1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.2.1.33 |
alcetherStatsTx512to1023OctetsThe total number of transmitted frames that were between
512 and 1023 bytes in length inclusive (excluding framing bits
but including FCS bytes).ro Counter64 .1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.2.1.34 |
alcetherStatsTx1024to1518OctetsThe total number of transmitted frames that were between
1024 and 1518 bytes in length inclusive (excluding framing bits
but including FCS bytes).ro Counter64 .1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.2.1.35 |
alcetherStatsTx1519to2047OctetsThe total number of transmitted frames that were between
1519 and 2047 bytes in length inclusive (excluding framing bits
but including FCS bytes).ro Counter64 .1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.2.1.36 |
alcetherStatsTx2048to4095OctetsThe total number of transmitted frames that were between
2048 and 4095 bytes in length inclusive (excluding framing bits
but including FCS bytes).ro Counter64 .1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.2.1.37 |
alcetherStatsTx4096OctetsThe total number of transmitted frames that were greater than
or equal to 4096 bytes in length and less than Max frame length
(excluding framing bits but including FCS bytes).ro Counter64 .1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.2.1.38 |
alcetherStatsTxRetryCountThe total number of collisions that the frames faced during
transmission attempts.ro Counter64 .1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.2.1.39 |
alcetherStatsTxVlanTagPktsThe total number of transmitted frames for which Type/Length field contains the
VLAN protocol identifier (0x8100).ro Counter64 .1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.2.1.40 |
alcetherStatsTxControlPktsThe total number of transmitted frames that were recognised as control frames.ro Counter64 .1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.2.1.41 |
alcetherStatsTxLatePktsThe total number of late collisions that occured beyond the collision window.ro Counter64 .1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.2.1.42 |
alcetherStatsTxTotalBytesOnWireThe total number of bytes transmitted on wire, including all bytes from collided
attempts.ro Counter64 .1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.2.1.43 |
alcetherStatsTxLenChkErrPktsThe total number of transmitted frames for which the frame length field value
in the Type/Length field does not match the actual data bytes length and
is NOT a Type field.ro Counter64 .1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.2.1.44 |
alcetherStatsTxExcDeferPktsThe total number of frames that were deferred in excess of 6071 nibble-times
in 100 Mbps, 24287 bit-times in 10 Mbps mode. These frames are dropped.(This
stat is only in case of Half duplex and excessive defer bit reset).ro Counter64 .1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.2.1.45 |
esmHybridConfTableA list of inactive hybrid port instances. SEQUENCE OF EsmHybridConfEntry .1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.3 |
esmHybridConfEntryA ESM Physical Port entry. EsmHybridConfEntry .1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.3.1 |
esmHybridPortCfgSpeedThe configured port line speed of this ESM port.rw Enumeration .1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.3.1.1 |
esmHybridPortCfgDuplexModeThe configured port duplex mode of this ESM port.
Note: GigaEthernet support only full-duplex.rw Enumeration .1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.3.1.2 |
esmHybridPortCfgAutoNegotiationAllow the user to enable or disable the port auto negotiation.rw Enumeration .1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.3.1.3 |
esmHybridPortCfgCrossoverAllow the user to configure port crossover.rw Enumeration .1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.3.1.4 |
esmHybridPortCfgFlowThis object is used for flow control of hybrid ports. It is similar to the dot3PauseAdminMode
object in dot3PauseTable. It is used to configure pause for fiber media.rw Enumeration .1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.3.1.5 |
esmHybridPortCfgInactiveTypeThis object is only applicable to hybrid ports .
It indicates the configured inactive media type.ro Enumeration .1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.3.1.6 |
ddmInfoTableThe ddmInfoTable has an entry for each SFP/XFP in the
system that supports Digital Diagnostic Monitoring (DDM). The table is
indexed by ifIndex. Each row in this table is dynamically added
and removed internally by the system based on the presence or absence
of DDM capable SFP/XFP components.deprecated SEQUENCE OF DdmEntry .1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.5 |
ddmInfoEntryEach row represents a particular SFP/XFP that supports Digital
Diagnostic Monitoring.
Entries are created and deleted internally by the system. DdmEntry .1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.5.1 |
ddmTemperatureThe value of ddmTemperature indicates the current temperature
of the SFP/XFP in 1000s of degrees Celsius.
A value of -200000 indicates this object is not applicable.ro Integer32 (-200000 | -150000..150000) UNITS "thousandth of a degree celcius" .1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.5.1.1 |
ddmTempLowWarningThe value of ddmTempLowWarning indicates the temperature
of the SFP/XFP in 1000s of degrees Celsius that triggers a low-warning.
A value of -200000 indicates this object is not applicable.ro Integer32 (-200000 | -150000..150000) UNITS "thousandth of a degree celcius" .1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.5.1.2 |
ddmTempLowAlarmThe value of ddmTempLowAlarm indicates the temperature
of the SFP/XFP in 1000s of degrees Celsius that triggers a low-alarm.
A value of -200000 indicates this object is not applicable.ro Integer32 (-200000 | -150000..150000) UNITS "thousandth of a degree celcius" .1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.5.1.3 |
ddmTempHiWarningThe value of ddmTempHiWarning indicates the temperature
of the SFP/XFP in 1000s of degrees Celsius that triggers a hi-warning.
A value of -200000 indicates this object is not applicable.ro Integer32 (-200000 | -150000..150000) UNITS "thousandth of a degree celcius" .1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.5.1.4 |
ddmTempHiAlarmThe value of ddmTempHiAlarm indicates the temperature
of the SFP/XFP in 1000s of degrees Celsius that triggers a hi-alarm.
A value of -200000 indicates this object is not applicable.ro Integer32 (-200000 | -150000..150000) UNITS "thousandth of a degree celcius" .1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.5.1.5 |
ddmSupplyVoltageThe value of ddmSupplyVoltage indicates the current supply
voltage of the SFP/XFP in 1000s of Volts (V).
A value of -200000 indicates this object is not applicable.ro Integer32 (-200000 | 0..10000) UNITS "thousandth of a volt" .1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.5.1.6 |
ddmSupplyVoltageLowWarningThe value of ddmSupplyVoltageLowWarning indicates the supply
voltage of the SFP/XFP in 1000s of Volts (V) that triggers a low-warning.
A value of -200000 indicates this object is not applicable.ro Integer32 (-200000 | 0..10000) UNITS "thousandth of a volt" .1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.5.1.7 |
ddmSupplyVoltageLowAlarmThe value of ddmSupplyVoltageLowAlarm indicates the supply
voltage of the SFP/XFP in 1000s of Volts (V) that triggers a low-alarm.
A value of -200000 indicates this object is not applicable.ro Integer32 (-200000 | 0..10000) UNITS "thousandth of a volt" .1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.5.1.8 |
ddmSupplyVoltageHiWarningThe value of ddmSupplyVoltageHiWarning indicates the supply
voltage of the SFP/XFP in 1000s of Volts (V) that triggers a hi-warning.
A value of -200000 indicates this object is not applicable.ro Integer32 (-200000 | 0..10000) UNITS "thousandth of a volt" .1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.5.1.9 |
ddmSupplyVoltageHiAlarmThe value of ddmSupplyVoltageHiAlarm indicates the supply
voltage of the SFP/XFP in 1000s of Volts (V) that triggers a hi-alarm.
A value of -200000 indicates this object is not applicable.ro Integer32 (-200000 | 0..10000) UNITS "thousandth of a volt" .1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.5.1.10 |
ddmTxBiasCurrentThe value of ddmTxBiasCurrent indicates the current Transmit
Bias Current of the SFP/XFP in 1000s of milli-Amperes (mA).
A value of -200000 indicates this object is not applicable.ro Integer32 (-200000 | 0..10000) UNITS "thousandth of a milli-Ampere" .1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.5.1.11 |
ddmTxBiasCurrentLowWarningThe value of ddmTxBiasCurrentLowWarning indicates the Transmit
Bias Current of the SFP/XFP in 1000s of milli-Amperes (mA) that triggers a
low-warning.
A value of -200000 indicates this object is not applicable.ro Integer32 (-200000 | 0..10000) UNITS "thousandth of a milli-Ampere" .1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.5.1.12 |
ddmTxBiasCurrentLowAlarmThe value of ddmTxBiasCurrentLowAlarm indicates the Transmit
Bias Current of the SFP/XFP in 1000s of milli-Amperes (mA) that triggers a
low-alarm.
A value of -200000 indicates this object is not applicable.ro Integer32 (-200000 | 0..10000) UNITS "thousandth of a milli-Ampere" .1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.5.1.13 |
ddmTxBiasCurrentHiWarningThe value of ddmTxBiasCurrentHiWarning indicates the Transmit
Bias Current of the SFP/XFP in 1000s milli-Amperes (mA) that triggers a
hi-warning.
A value of -200000 indicates this object is not applicable.ro Integer32 (-200000 | 0..10000) UNITS "thousandth of a milli-Ampere" .1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.5.1.14 |
ddmTxBiasCurrentHiAlarmThe value of ddmTxBiasCurrentHiAlarm indicates the Transmit
Bias Current of the SFP/XFP in 1000s milli-Amperes (mA) that triggers a
hi-alarm.
A value of -200000 indicates this object is not applicable.ro Integer32 (-200000 | 0..10000) UNITS "thousandth of a milli-Ampere" .1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.5.1.15 |
ddmTxOutputPowerThe value of ddmTxOutputPower indicates the current Output
Power of the SFP/XFP in 1000s of dBm.
A value of -200000 indicates this object is not applicable.ro Integer32 (-200000 | -40000..10000) UNITS "thousandth of a dBm" .1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.5.1.16 |
ddmTxOutputPowerLowWarningThe value of ddmTxOutputPowerLowWarning indicates the Output Power
of the SFP/XFP in 1000s of dBm that triggers a low-warning.
A value of -200000 indicates this object is not applicable.ro Integer32 (-200000 | -40000..10000) UNITS "thousandth of a dBm" .1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.5.1.17 |
ddmTxOutputPowerLowAlarmThe value of ddmTxOutputPowerLowAlarm indicates the Output Power
of the SFP/XFP in 1000s of dBm that triggers a low-alarm.
A value of -200000 indicates this object is not applicable.ro Integer32 (-200000 | -40000..10000) UNITS "thousandth of a dBm" .1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.5.1.18 |
ddmTxOutputPowerHiWarningThe value of ddmTxOutputPowerHiWarning indicates the Output Power
of the SFP/XFP in 1000s of dBm that triggers a hi-alarm.
A value of -200000 indicates this object is not applicable.ro Integer32 (-200000 | -40000..10000) UNITS "thousandth of a dBm" .1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.5.1.19 |
ddmTxOutputPowerHiAlarmThe value of ddmTxOutputPowerHiAlarm indicates the Output Power
of the SFP/XFP in 1000s of dBm that triggers a hi-alarm.
A value of -200000 indicates this object is not applicable.ro Integer32 (-200000 | -40000..10000) UNITS "thousandth of a dBm" .1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.5.1.20 |
ddmRxOpticalPowerThe value of ddmRxOpticalPower indicates the current Received
Optical Power of the SFP/XFP in 1000s of dBm.
A value of -200000 indicates this object is not applicable.ro Integer32 (-200000 | -40000..10000) UNITS "thousandth of a dBm" .1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.5.1.21 |
ddmRxOpticalPowerLowWarningThe value of ddmRxOpticalPowerLowWarning indicates the Received
Optical Power of the SFP/XFP in 1000s of dBm that triggers a
low-warning.
A value of -200000 indicates this object is not applicable.ro Integer32 (-200000 | -40000..10000) UNITS "thousandth of a dBm" .1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.5.1.22 |
ddmRxOpticalPowerLowAlarmThe value of ddmRxOpticalPowerLowAlarm indicates the Received
Optical Power of the SFP/XFP in 1000s of dBm that triggers a
low-alarm.
A value of -200000 indicates this object is not applicable.ro Integer32 (-200000 | -40000..10000) UNITS "thousandth of a dBm" .1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.5.1.23 |
ddmRxOpticalPowerHiWarningThe value of ddmRxOpticalPowerHiWarning indicates the Received
Optical Power of the SFP/XFP in 1000s of dBm that triggers a
hi-warning.
A value of -200000 indicates this object is not applicable.ro Integer32 (-200000 | -40000..10000) UNITS "thousandth of a dBm" .1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.5.1.24 |
ddmRxOpticalPowerHiAlarmThe value of ddmRxOpticalPowerHiAlarm indicates the Received
Optical Power of the SFP/XFP in 1000s of dBm that triggers a
hi-alarm.
A value of -200000 indicates this object is not applicable.ro Integer32 (-200000 | -40000..10000) UNITS "thousandth of a dBm" .1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.5.1.25 |
ddmPortInfoTableThe ddmPortInfoTable has an entry for each SFP/XFP in the
system that supports Digital Diagnostic Monitoring (DDM). The table is
indexed by ifIndex and port channel. Each row in this table is
dynamically added
and removed internally by the system based on the presence or absence
of DDM capable SFP/XFP components. SEQUENCE OF DdmPortEntry .1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.6 |
ddmPortInfoEntryEach row represents a particular SFP/XFP that supports Digital
Diagnostic Monitoring.
Entries are created and deleted internally by the system. DdmPortEntry .1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.6.1 |
ddmPortChannelThe channel number of the data that is being read. In the case
of a QSFP there will be 4 10 gigabyte channels, for SFP/XFP there
will only be one.ro Integer32 .1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.6.1.1 |
ddmPortTemperatureThe value of ddmTemperature indicates the current temperature
of the SFP/XFP in 1000s of degrees Celsius.
A value of -200000 indicates this object is not applicable.ro Integer32 (-200000 | -150000..150000) UNITS "thousandth of a degree celcius" .1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.6.1.2 |
ddmPortTempLowWarningThe value of ddmTempLowWarning indicates the temperature
of the SFP/XFP in 1000s of degrees Celsius that triggers a low-warning.
A value of -200000 indicates this object is not applicable.ro Integer32 (-200000 | -150000..150000) UNITS "thousandth of a degree celcius" .1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.6.1.3 |
ddmPortTempLowAlarmThe value of ddmTempLowAlarm indicates the temperature
of the SFP/XFP in 1000s of degrees Celsius that triggers a low-alarm.
A value of -200000 indicates this object is not applicable.ro Integer32 (-200000 | -150000..150000) UNITS "thousandth of a degree celcius" .1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.6.1.4 |
ddmPortTempHiWarningThe value of ddmTempHiWarning indicates the temperature
of the SFP/XFP in 1000s of degrees Celsius that triggers a hi-warning.
A value of -200000 indicates this object is not applicable.ro Integer32 (-200000 | -150000..150000) UNITS "thousandth of a degree celcius" .1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.6.1.5 |
ddmPortTempHiAlarmThe value of ddmTempHiAlarm indicates the temperature
of the SFP/XFP in 1000s of degrees Celsius that triggers a hi-alarm.
A value of -200000 indicates this object is not applicable.ro Integer32 (-200000 | -150000..150000) UNITS "thousandth of a degree celcius" .1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.6.1.6 |
ddmPortSupplyVoltageThe value of ddmSupplyVoltage indicates the current supply
voltage of the SFP/XFP in 1000s of Volts (V).
A value of -200000 indicates this object is not applicable.ro Integer32 (-200000 | 0..10000) UNITS "thousandth of a volt" .1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.6.1.7 |
ddmPortSupplyVoltageLowWarningThe value of ddmSupplyVoltageLowWarning indicates the supply
voltage of the SFP/XFP in 1000s of Volts (V) that triggers a low-warning.
A value of -200000 indicates this object is not applicable.ro Integer32 (-200000 | 0..10000) UNITS "thousandth of a volt" .1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.6.1.8 |
ddmPortSupplyVoltageLowAlarmThe value of ddmSupplyVoltageLowAlarm indicates the supply
voltage of the SFP/XFP in 1000s of Volts (V) that triggers a low-alarm.
A value of -200000 indicates this object is not applicable.ro Integer32 (-200000 | 0..10000) UNITS "thousandth of a volt" .1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.6.1.9 |
ddmPortSupplyVoltageHiWarningThe value of ddmSupplyVoltageHiWarning indicates the supply
voltage of the SFP/XFP in 1000s of Volts (V) that triggers a hi-warning.
A value of -200000 indicates this object is not applicable.ro Integer32 (-200000 | 0..10000) UNITS "thousandth of a volt" .1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.6.1.10 |
ddmPortSupplyVoltageHiAlarmThe value of ddmSupplyVoltageHiAlarm indicates the supply
voltage of the SFP/XFP in 1000s of Volts (V) that triggers a hi-alarm.
A value of -200000 indicates this object is not applicable.ro Integer32 (-200000 | 0..10000) UNITS "thousandth of a volt" .1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.6.1.11 |
ddmPortTxBiasCurrentThe value of ddmTxBiasCurrent indicates the current Transmit
Bias Current of the SFP/XFP in 1000s of milli-Amperes (mA).
A value of -200000 indicates this object is not applicable.ro Integer32 (-200000 | 0..10000) UNITS "thousandth of a milli-Ampere" .1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.6.1.12 |
ddmPortTxBiasCurrentLowWarningThe value of ddmTxBiasCurrentLowWarning indicates the Transmit
Bias Current of the SFP/XFP in 1000s of milli-Amperes (mA) that triggers a
low-warning.
A value of -200000 indicates this object is not applicable.ro Integer32 (-200000 | 0..10000) UNITS "thousandth of a milli-Ampere" .1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.6.1.13 |
ddmPortTxBiasCurrentLowAlarmThe value of ddmTxBiasCurrentLowAlarm indicates the Transmit
Bias Current of the SFP/XFP in 1000s of milli-Amperes (mA) that triggers a
low-alarm.
A value of -200000 indicates this object is not applicable.ro Integer32 (-200000 | 0..10000) UNITS "thousandth of a milli-Ampere" .1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.6.1.14 |
ddmPortTxBiasCurrentHiWarningThe value of ddmTxBiasCurrentHiWarning indicates the Transmit
Bias Current of the SFP/XFP in 1000s milli-Amperes (mA) that triggers a
hi-warning.
A value of -200000 indicates this object is not applicable.ro Integer32 (-200000 | 0..10000) UNITS "thousandth of a milli-Ampere" .1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.6.1.15 |
ddmPortTxBiasCurrentHiAlarmThe value of ddmTxBiasCurrentHiAlarm indicates the Transmit
Bias Current of the SFP/XFP in 1000s milli-Amperes (mA) that triggers a
hi-alarm.
A value of -200000 indicates this object is not applicable.ro Integer32 (-200000 | 0..10000) UNITS "thousandth of a milli-Ampere" .1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.6.1.16 |
ddmPortTxOutputPowerThe value of ddmTxOutputPower indicates the current Output
Power of the SFP/XFP in 1000s of dBm.
A value of -200000 indicates this object is not applicable.ro Integer32 (-200000 | -40000..10000) UNITS "thousandth of a dBm" .1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.6.1.17 |
ddmPortTxOutputPowerLowWarningThe value of ddmTxOutputPowerLowWarning indicates the Output Power
of the SFP/XFP in 1000s of dBm that triggers a low-warning.
A value of -200000 indicates this object is not applicable.ro Integer32 (-200000 | -40000..10000) UNITS "thousandth of a dBm" .1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.6.1.18 |
ddmPortTxOutputPowerLowAlarmThe value of ddmTxOutputPowerLowAlarm indicates the Output Power
of the SFP/XFP in 1000s of dBm that triggers a low-alarm.
A value of -200000 indicates this object is not applicable.ro Integer32 (-200000 | -40000..10000) UNITS "thousandth of a dBm" .1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.6.1.19 |
ddmPortTxOutputPowerHiWarningThe value of ddmTxOutputPowerHiWarning indicates the Output Power
of the SFP/XFP in 1000s of dBm that triggers a hi-alarm.
A value of -200000 indicates this object is not applicable.ro Integer32 (-200000 | -40000..10000) UNITS "thousandth of a dBm" .1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.6.1.20 |
ddmPortTxOutputPowerHiAlarmThe value of ddmTxOutputPowerHiAlarm indicates the Output Power
of the SFP/XFP in 1000s of dBm that triggers a hi-alarm.
A value of -200000 indicates this object is not applicable.ro Integer32 (-200000 | -40000..10000) UNITS "thousandth of a dBm" .1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.6.1.21 |
ddmPortRxOpticalPowerThe value of ddmRxOpticalPower indicates the current Received
Optical Power of the SFP/XFP in 1000s of dBm.
A value of -200000 indicates this object is not applicable.ro Integer32 (-200000 | -40000..10000) UNITS "thousandth of a dBm" .1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.6.1.22 |
ddmPortRxOpticalPowerLowWarningThe value of ddmRxOpticalPowerLowWarning indicates the Received
Optical Power of the SFP/XFP in 1000s of dBm that triggers a
low-warning.
A value of -200000 indicates this object is not applicable.ro Integer32 (-200000 | -40000..10000) UNITS "thousandth of a dBm" .1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.6.1.23 |
ddmPortRxOpticalPowerLowAlarmThe value of ddmRxOpticalPowerLowAlarm indicates the Received
Optical Power of the SFP/XFP in 1000s of dBm that triggers a
low-alarm.
A value of -200000 indicates this object is not applicable.ro Integer32 (-200000 | -40000..10000) UNITS "thousandth of a dBm" .1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.6.1.24 |
ddmPortRxOpticalPowerHiWarningThe value of ddmRxOpticalPowerHiWarning indicates the Received
Optical Power of the SFP/XFP in 1000s of dBm that triggers a
hi-warning.
A value of -200000 indicates this object is not applicable.ro Integer32 (-200000 | -40000..10000) UNITS "thousandth of a dBm" .1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.6.1.25 |
ddmPortRxOpticalPowerHiAlarmThe value of ddmRxOpticalPowerHiAlarm indicates the Received
Optical Power of the SFP/XFP in 1000s of dBm that triggers a
hi-alarm.
A value of -200000 indicates this object is not applicable.ro Integer32 (-200000 | -40000..10000) UNITS "thousandth of a dBm" .1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.6.1.26 |
alcfcStatsTableA list of Fiber Channel statistics entries. SEQUENCE OF AlcfcStatsEntry .1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.7 |
alcfcStatsEntryA collection of statistics kept for a particular
Fiber Channel interface. As an example, an instance of the
fcStatsPkts object might be named alcfcStatsPkts.1 AlcfcStatsEntry .1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.7.1 |
alcfcClearStatsUsed to Clear all Statistics counters.
By default, this object contains zero value.rw Enumeration .1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.7.1.1 |
alcfcLastClearStatsThe value of SysUpTime at the time of all
the statistics counters are cleared.
By default, this object contains a zero value.ro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.7.1.2 |
alcfcStatsRxUndersizePktsThe total number of packets received that were
less than 36 octets long (excluding framing bits,
but including FCS octets) and were otherwise well
formed.ro Counter64 .1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.7.1.3 |
alcfcStatsTxBBCreditZerosThe number of transitions in/out of the buffer-to-buffer
credit zero state.ro Counter64 .1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.7.1.6 |
alcfcStatsRxBBCreditZerosThe number of times RX BBCredit drops to zero.ro Counter64 .1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.7.1.7 |
alcfcStatsLinkFailuresThe number of link failures.ro Counter64 .1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.7.1.8 |
alcfcStatsLossofSynchsThe number of loss of word-sync detected.ro Counter64 .1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.7.1.9 |
alcfcStatsLossofSignalsThe number of loss of signals detected.ro Counter64 .1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.7.1.10 |
alcfcStatsPrimSeqProtocolErrorsThe number of primitive sequence protocol errors detected.ro Counter64 .1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.7.1.11 |
alcfcStatsInvalidTxWordsThe number of invalid transmission words. This includes
invalid ordered sets and invalid data words.ro Counter64 .1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.7.1.12 |
alcfcStatsInvalidCRCsThe number of frames received with an invalid CRC.ro Counter64 .1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.7.1.13 |
alcfcStatsInvalidOrderedSetsThe number of invalid ordered sets received at this port.ro Counter64 .1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.7.1.14 |
alcfcStatsFrameTooLongsThe number of frames received at this port for which the
frame length was greater than what was agreed to in
FLOGI/PLOGI.ro Counter64 .1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.7.1.15 |
alcfcStatsDelimiterErrorsThe number of invalid delimiters receivedro Counter64 .1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.7.1.16 |
alcfcStatsEncodingDisparityErrorsThe number of detected running disparity at 10b/8b level.ro Counter64 .1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.7.1.17 |
alcfcStatsOtherErrorsThe number of errors detected but not counted by any other
error counter. This only includes RX frames drops due to zero
RX BBCreditsro Counter64 .1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.7.1.18 |
ddmConfiguration OBJECT IDENTIFIER .1.3.6.1.4.1.6486.801.1.2.1.5.1.1.4 |
ddmConfigThis object enables/disables DDM software feature in the system.rw Enumeration .1.3.6.1.4.1.6486.801.1.2.1.5.1.1.4.1 |
ddmTrapConfigThis objects enables/disables traps for DDM warning/alarm threshold violations.rw Enumeration .1.3.6.1.4.1.6486.801.1.2.1.5.1.1.4.2 |
ddmNotificationTypeThis object defines the trap type for monitored DDM parameters.ro Enumeration .1.3.6.1.4.1.6486.801.1.2.1.5.1.1.4.3 |
portViolations OBJECT IDENTIFIER .1.3.6.1.4.1.6486.801.1.2.1.5.1.1.5 |
portViolationTableThis table contains the port Violations per port. SEQUENCE OF PortViolationEntry .1.3.6.1.4.1.6486.801.1.2.1.5.1.1.5.1 |
portViolationEntryPort Violation Entry. The entries in this table are indexed
by 3 units,
1. ifIndex of the port for which the violation is set
2. source of the violation, the feature or module
3. reason for the violation (sub reason under each source). PortViolationEntry .1.3.6.1.4.1.6486.801.1.2.1.5.1.1.5.1.1 |
portViolationIfIndexThe IfIndex of the port that has a violation. InterfaceIndex (IF-MIB) .1.3.6.1.4.1.6486.801.1.2.1.5.1.1.5.1.1.1 |
portViolationSourceIndicates the source of the port violation.
The source is the feature or module that has
caused the violation. The list is given below
1. Initiated by Source Learning
2. Initiated by QOS Policy
3. Initiated by Net Sec
4. Initiated by UDLD
5. Initiated by NI supervison (Fabric Stability).
When there is no value the value of this will be 0 Enumeration .1.3.6.1.4.1.6486.801.1.2.1.5.1.1.5.1.1.2 |
portViolationReasonThe Reason for the port violation. This will be application
specific. The Reason indicate the violation for the 1st Violation
that happened on this port. Enumeration .1.3.6.1.4.1.6486.801.1.2.1.5.1.1.5.1.1.3 |
portViolationActionThe action determines on violation, what action will
taken. Either the port would be shutdown or Admin Down
or wait for the timer to expire and the timerAction
will determine what needs to be done.ro Enumeration .1.3.6.1.4.1.6486.801.1.2.1.5.1.1.5.1.1.4 |
portViolationTimerIf any timer is associated with the violation
This is Zero if no timer is associated.ro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.6486.801.1.2.1.5.1.1.5.1.1.5 |
portViolationTimerActionThe Timer related action.
If set to portDownAfterTimer, no operation will be performed on
the port and the port will be shutdown after timer expiry.
If set to portUpAfterTimer the port will be shutdown immediately
and after the timer expiry the port will brought up..ro Enumeration .1.3.6.1.4.1.6486.801.1.2.1.5.1.1.5.1.1.6 |
portViolationClearPortWhen this MIB object is set all violation on the
given port will be cleared. The Indices portViolationSource and
portViolationReason should be set to 0rw Enumeration .1.3.6.1.4.1.6486.801.1.2.1.5.1.1.5.1.1.7 |
alaLinkMonConfigTableA list of Link Monitoring Configuration Parameters SEQUENCE OF AlaLinkMonConfigEntry .1.3.6.1.4.1.6486.801.1.2.1.5.1.1.5.2 |
alaLinkMonConfigEntryA collection of Link Monitoring configurations kept for a particular
Ethernet interface. AlaLinkMonConfigEntry .1.3.6.1.4.1.6486.801.1.2.1.5.1.1.5.2.1 |
alaLinkMonStatusAllows the user to enable or disable Link Monitoring on the port.rw Enumeration .1.3.6.1.4.1.6486.801.1.2.1.5.1.1.5.2.1.1 |
alaLinkMonTimeWindowIndicates the number of seconds the Link will be monitored for a port.rw Integer32 .1.3.6.1.4.1.6486.801.1.2.1.5.1.1.5.2.1.2 |
alaLinkMonLinkFlapThresholdIndicaes the number of link flaps allowed for the specified port during the time window before the port is shutdown.rw Integer32 .1.3.6.1.4.1.6486.801.1.2.1.5.1.1.5.2.1.3 |
alaLinkMonLinkErrorThresholdIndicates the number of link errors allowed on Rx for the specified port during the time window before the port is shutdown. The errors are the MAC errors that include CRC, lost frames, error frames, alignment frames.rw Integer32 .1.3.6.1.4.1.6486.801.1.2.1.5.1.1.5.2.1.4 |
alaLinkMonWaitToRestoreTimerIndicates the number of seconds after which the link up event is notified to other applications. The timer is started whenever a Link Up is detected on a port being monitored.rw Integer32 .1.3.6.1.4.1.6486.801.1.2.1.5.1.1.5.2.1.5 |
alaLinkMonWaitToShutdownTimerIndicates the number of milli seconds after which the link down event is notified to other applications. The timer is started whenever a Link down is detected on a port being monitored.rw Integer32 .1.3.6.1.4.1.6486.801.1.2.1.5.1.1.5.2.1.6 |
alaLinkMonStatsTableA list of Link Monitoring Statistics SEQUENCE OF AlaLinkMonStatsEntry .1.3.6.1.4.1.6486.801.1.2.1.5.1.1.5.3 |
alaLinkMonStatsEntryA collection of Link Monitoring statistics for a particular Ethernet interface. AlaLinkMonStatsEntry .1.3.6.1.4.1.6486.801.1.2.1.5.1.1.5.3.1 |
alaLinkMonStatsClearStatsUsed to Clear all Statistics counters.
The value reset (1) indicates that Link Monitoring shuold all statistic counters related to the particular port.
By default, this object contains zero value.rw Enumeration .1.3.6.1.4.1.6486.801.1.2.1.5.1.1.5.3.1.1 |
alaLinkMonStatsPortStateIndicates the status of the port.
up(1) means the port is physically up,
down(2) means the port is physically down,
shutdown(3) means the interface is shutdown because of excessive link flaps or link errors.ro Enumeration .1.3.6.1.4.1.6486.801.1.2.1.5.1.1.5.3.1.2 |
alaLinkMonStatsCurrentLinkFlapsIndicates the number of Link flaps in the current time window.ro Counter64 .1.3.6.1.4.1.6486.801.1.2.1.5.1.1.5.3.1.3 |
alaLinkMonStatsCurrentErrorFramesIndicates the number of error frames in the current time window.ro Counter64 .1.3.6.1.4.1.6486.801.1.2.1.5.1.1.5.3.1.4 |
alaLinkMonStatsCurrentCRCErrorsIndicates the number of CRC errors in the current time window.ro Counter64 .1.3.6.1.4.1.6486.801.1.2.1.5.1.1.5.3.1.5 |
alaLinkMonStatsCurrentLostFramesIndicates the number of Rx Lost frames in the current time window.ro Counter64 .1.3.6.1.4.1.6486.801.1.2.1.5.1.1.5.3.1.6 |
alaLinkMonStatsCurrentAlignErrorsIndicates the number of Rx alignment frames in the current time window.ro Counter64 .1.3.6.1.4.1.6486.801.1.2.1.5.1.1.5.3.1.7 |
alaLinkMonStatsCurrentLinkErrorsIndicates the sum of all the MAC Errors within the current time window.
i.e., the sum of alaLinkMonStatsCurrentErrorFrames, alaLinkMonStatsCurrentCRCErrors,
alaLinkMonCurrentLosFrames, alaLinkMonStatsCurrentAlignErrors.ro Counter64 .1.3.6.1.4.1.6486.801.1.2.1.5.1.1.5.3.1.8 |
alaLinkMonStatsTotalLinkFlapsIndicates the total number of link flaps across all the time windows.ro Counter64 .1.3.6.1.4.1.6486.801.1.2.1.5.1.1.5.3.1.9 |
alaLinkMonStatsTotalLinkErrorsIndicates the total number of link errors across all the time windows.ro Counter64 .1.3.6.1.4.1.6486.801.1.2.1.5.1.1.5.3.1.10 |
alaLFPGroupTableA list of Link Fault Propagation Grooups and their status SEQUENCE OF AlaLFPGroupEntry .1.3.6.1.4.1.6486.801.1.2.1.5.1.1.5.4 |
alaLFPGroupEntryThe list of Link Fault Propagation group id and status for each group AlaLFPGroupEntry .1.3.6.1.4.1.6486.801.1.2.1.5.1.1.5.4.1 |
alaLFPGroupIdIndicates the unique group id for Link Fault Propagation (LFP).ro Integer32(1 .. 8 ) .1.3.6.1.4.1.6486.801.1.2.1.5.1.1.5.4.1.1 |
alaLFPGroupAdminStatusIndicates the admin status of the group. disable(2) means link fault propagation,
is disbaled. enable(1) means link fault propagation is enabledrw Enumeration .1.3.6.1.4.1.6486.801.1.2.1.5.1.1.5.4.1.2 |
alaLFPGroupOperStatusIndicates the operational status of the group. down(2) means all the source ports are down,
up(1) means atleast one source port in the group is up.ro Enumeration .1.3.6.1.4.1.6486.801.1.2.1.5.1.1.5.4.1.3 |
alaLFPGroupWaitToShutdown0 - Disable wait to shutdown timer
5 - 300 - after expiry of this timer all destination ports will be shutdownrw Integer32(0 .. 300) .1.3.6.1.4.1.6486.801.1.2.1.5.1.1.5.4.1.4 |
alaLFPGroupRowStatusRow Status for initiating a MIB retrieval request.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.6486.801.1.2.1.5.1.1.5.4.1.5 |
alaLFPConfigTableA list of Link Fault Propagation port and port type of each LFP group SEQUENCE OF AlaLFPConfigEntry .1.3.6.1.4.1.6486.801.1.2.1.5.1.1.5.5 |
alaLFPConfigEntryA list of Link Fault Propagation port and port type of each LFP group AlaLFPConfigEntry .1.3.6.1.4.1.6486.801.1.2.1.5.1.1.5.5.1 |
alaLFPConfigPortIndicates ifindex of source/destination port for a LFP Group.ro InterfaceIndex (IF-MIB) .1.3.6.1.4.1.6486.801.1.2.1.5.1.1.5.5.1.1 |
alaLFPConfigPortTypeIndicates the type of port, (1) means the port is destination port and
(2) means the port is a destination port for a LFP Group.rw Enumeration .1.3.6.1.4.1.6486.801.1.2.1.5.1.1.5.5.1.2 |
alaLFPConfigRowStatusRow Status for initiating a MIB retrieval request.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.6486.801.1.2.1.5.1.1.5.5.1.3 |
csmConfTrap OBJECT IDENTIFIER .1.3.6.1.4.1.6486.801.1.2.1.5.1.1.6 |
alaDyingGaspChassisIdThis object specifies the chassis id of the chassis whose NI is going down.ro Integer32 .1.3.6.1.4.1.6486.801.1.2.1.5.1.1.6.1 |
alaDyingGaspPowerSupplyTypeThis object specifies the type of the power supply.ro Enumeration .1.3.6.1.4.1.6486.801.1.2.1.5.1.1.6.2 |
alaDyingGaspTimeThis object specifies the time of power failure.ro DateAndTime (SNMPv2-TC) .1.3.6.1.4.1.6486.801.1.2.1.5.1.1.6.3 |
alcatelIND1PortMIBConformance OBJECT IDENTIFIER .1.3.6.1.4.1.6486.801.1.2.1.5.1.2 |
alcatelIND1PortMIBCompliances OBJECT IDENTIFIER .1.3.6.1.4.1.6486.801.1.2.1.5.1.2.1 |
alcatelIND1PortMIBGroups OBJECT IDENTIFIER .1.3.6.1.4.1.6486.801.1.2.1.5.1.2.2 |