ALCATEL-IND1-PIM-MIB
AI MIB Summary
The ALCATEL-IND1-PIM-MIB provides enterprise-specific SNMP access to configure and monitor global parameters for Protocol Independent Multicast (PIM) Sparse Mode (PIM-SM) and Dense Mode (PIM-DM) on Alcatel-Lucent networking hardware. This module enables the retrieval of multicast routing state data and the modification of PIM protocol settings to manage multicast group memberships and forwarding behavior.
This module describes an authoritative enterprise-specific Simple Network Management Protocol (SNMP) Management Information Base (MIB):
This proprietary MIB contains management information for the configuration of PIM-SM and PIM-DM global configuration parameters.
The right to make changes in specification and other information contained in this document without prior notice is reserved.
No liability shall be assumed for any incidental, indirect, special, or consequential damages whatsoever arising from or related to this document or the information contained herein.
Vendors, end-users, and other interested parties are granted non-exclusive license to use this specification in connection with management of the products for which it is intended to be used.
Copyright (C) 1995-2007 Alcatel-Lucent ALL RIGHTS RESERVED WORLDWIDE
Main OID:
alcatelIND1PIMMIB.1.3.6.1.4.1.6486.801.1.2.1.10.6.1
48
Objects
Active
Status
6
Dependencies
Imported Objects
Objects
48 total| Object Name |
|---|
alcatelIND1PIMMIBThis module describes an authoritative enterprise-specific Simple
Network Management Protocol (SNMP) Management Information Base (MIB):
This proprietary MIB contains management information for
the configuration of PIM-SM and PIM-DM global configuration
parameters.
The right to make changes in specification and other information
contained in this document without prior notice is reserved.
No liability shall be assumed for any incidental, indirect, special, or
consequential damages whatsoever arising from or related to this
document or the information contained herein.
Vendors, end-users, and other interested parties are granted
non-exclusive license to use this specification in connection with
management of the products for which it is intended to be used.
Copyright (C) 1995-2007 Alcatel-Lucent
ALL RIGHTS RESERVED WORLDWIDE MODULE-IDENTITY .1.3.6.1.4.1.6486.801.1.2.1.10.6.1 |
alaPimNotifications OBJECT IDENTIFIER .1.3.6.1.4.1.6486.801.1.2.1.10.6.1.0 |
alaPimNonBidirHelloAn alaPimNonBidirHello notification signifies that
a bidir-capable router has received a PIM hello from
a non-bidir-capable router.
This notification is generated whenever the counter
alaPimsmNonBidirHelloMsgsRcvd is incremented, subject
to the rate limit specified by
alaPimsmNonBidirHelloNotificationPeriod. NOTIFICATION-TYPE .1.3.6.1.4.1.6486.801.1.2.1.10.6.1.0.1 |
alcatelIND1PIMMIBObjects OBJECT IDENTIFIER .1.3.6.1.4.1.6486.801.1.2.1.10.6.1.1 |
alaPimsmGlobalConfig OBJECT IDENTIFIER .1.3.6.1.4.1.6486.801.1.2.1.10.6.1.1.1 |
alaPimsmAdminStatusAdministratively enables/disables the
PIM-SM protocol on this router.rw Enumeration .1.3.6.1.4.1.6486.801.1.2.1.10.6.1.1.1.1 |
alaPimsmMaxRPsThe maximum number of C-RPs allowed in the PIM-SM
domain.rw Integer32 .1.3.6.1.4.1.6486.801.1.2.1.10.6.1.1.1.2 |
alaPimsmProbeTimeWhen NULL Registers are used, this is the time
between sending a NULL Register and the Register-
Suppression-Timer expiring unless it is restarted
by receiving a Register-Stop.rw Integer32 .1.3.6.1.4.1.6486.801.1.2.1.10.6.1.1.1.3 |
alaPimsmOldRegisterMessageSupportSpecifies the application of the checksum function on
received Register messages in the PIM-SM domain. When
set to full(2), the checksum for a register message
is computed for the entire packet (i.e. includes data).
When set to header(1), the checksum is done only on the
first 8 bytes of the packet. This variable is provided
for interoperability reasons and may be required for
Compatibility with older implementations of PIM-SM v2.
This parameter must be set the same throughout the
PIM-SM domain.rw Enumeration .1.3.6.1.4.1.6486.801.1.2.1.10.6.1.1.1.4 |
alaPimsmAdminSPTConfigAdministratively enables/disables SPT Switchover
upon receiving the first data packet.rw Enumeration .1.3.6.1.4.1.6486.801.1.2.1.10.6.1.1.1.5 |
alaPimsmRPThresholdSets the RP threshold value (in bps) to be used
in determining when to switch to native
forwarding at the RP. The value of 0
disables the RP Threshold functionality.rw Integer32 .1.3.6.1.4.1.6486.801.1.2.1.10.6.1.1.1.6 |
alaPimsmV6AdminStatusAdministratively enables/disables the
PIM-SM IPv6 protocol on this router.rw Enumeration .1.3.6.1.4.1.6486.801.1.2.1.10.6.1.1.1.7 |
alaPimsmV6SPTConfigAdministratively enables/disables PIM IPv6 SPT Switchover
upon receiving the first data packet.rw Enumeration .1.3.6.1.4.1.6486.801.1.2.1.10.6.1.1.1.8 |
alaPimsmV6RPSwitchoverAdministratively enables/disables whether PIM IPv6
will attempt to switch to native forwarding at the RP
upon receiving the first register-encapsulated packet.rw Enumeration .1.3.6.1.4.1.6486.801.1.2.1.10.6.1.1.1.9 |
alaPimsmBidirStatusAdministratively enables/disables the
PIM BIDIR protocol on this router.ro Enumeration .1.3.6.1.4.1.6486.801.1.2.1.10.6.1.1.1.10 |
alaPimsmBidirPeriodicIntervalThis is the interval at which the DF for each RPA
will periodically announce its status in a
Winner message.
A value of 0 indicates that periodic messages will
not be sent.rw Integer32 .1.3.6.1.4.1.6486.801.1.2.1.10.6.1.1.1.11 |
alaPimsmBidirDFAbortAdministratively enables/disables whether the DF
election will be automatically aborted if a PIM hello
is received from a PIM neighbor without the
bidirectional capable option. By default, the DF
election will still occur among those PIM routers that
support BIDIR. By enabling this option, if a BIDIR-
capable router receives a PIM hello from a
non-BIDIR-capable router, the DF election is aborted.rw Enumeration .1.3.6.1.4.1.6486.801.1.2.1.10.6.1.1.1.12 |
alaPimsmNonBidirHelloPeriodThe minimum time that must elapse between
alaPimNonBidirHello notifications originated by this router.
The default value of 65535 represents an 'infinite' time, in
which case, no alaPimNonBidirHello notifications are ever
sent.
The non-zero minimum allowed value provides resilience
against propagation of denial-of-service attacks from the
control plane to the network management plane.rw Unsigned32 .1.3.6.1.4.1.6486.801.1.2.1.10.6.1.1.1.13 |
alaPimsmNonBidirHelloMsgsRcvdThe number of PIM Hello messages that have been
received by a BIDIR-capable device that do not have the
Bidirectional Capable option.
This counter is incremented if BIDIR mode is enabled on
this router and a PIM Hello message is received from a
PIM neighbor that does not include the Bidirectional Capable
option.
By default, the reception of these messages will not
effect the BIDIR DF election. The alaPimsmBidirDFAbort
object may be used to change the default behavior
and have the DF election aborted whenever a BIDIR-capable
router receives a PIM hello from a non-BIDIR-capable
router.ro Counter32 .1.3.6.1.4.1.6486.801.1.2.1.10.6.1.1.1.14 |
alaPimsmNonBidirHelloAddressTypeThe address type stored in alaPimsmNonBidirHelloOrigin.
If no Non Bidir Hello messages have been received, this
object is set to unknown(0).ro InetAddressType (INET-ADDRESS-MIB) .1.3.6.1.4.1.6486.801.1.2.1.10.6.1.1.1.15 |
alaPimsmNonBidirHelloOriginThe source address of the last Non Bidir Hello message
received by this device.ro InetAddress .1.3.6.1.4.1.6486.801.1.2.1.10.6.1.1.1.16 |
alaPimsmV6BidirStatusAdministratively enables/disables the
PIM IPv6 BIDIR protocol on this router.ro Enumeration .1.3.6.1.4.1.6486.801.1.2.1.10.6.1.1.1.17 |
alaPimdmGlobalConfig OBJECT IDENTIFIER .1.3.6.1.4.1.6486.801.1.2.1.10.6.1.1.2 |
alaPimdmAdminStatusAdministratively enables/disables the
PIM-DM protocol on this router.rw Enumeration .1.3.6.1.4.1.6486.801.1.2.1.10.6.1.1.2.1 |
alaPimdmStateRefreshTimeToLiveThe TTL to be used by this router's originated State
Refresh messages if the data packet's TTL is not
recorded.rw Integer32 .1.3.6.1.4.1.6486.801.1.2.1.10.6.1.1.2.2 |
alaPimdmStateRefreshLimitIntervalThis router will not forward successive State Refresh
messages received at less than this interval.rw TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.6486.801.1.2.1.10.6.1.1.2.3 |
alaPimdmV6AdminStatusAdministratively enables/disables the
PIM-DM IPv6 protocol on this router.rw Enumeration .1.3.6.1.4.1.6486.801.1.2.1.10.6.1.1.2.4 |
alaPimdmDenseGroupTableThis table is used to manage configuration of dense groups.
If the group prefixes configured for two or more rows in
this table overlap, the row with the greatest value of
alaPimdmDenseGroupGrpPrefixLength is used for the overlapping
range. SEQUENCE OF AlaPimdmDenseGroupEntry .1.3.6.1.4.1.6486.801.1.2.1.10.6.1.1.2.5 |
alaPimdmDenseGroupEntryAn entry (conceptual row) in the alaPimdmDenseGroupTable. This
entry is preserved on agent restart. AlaPimdmDenseGroupEntry .1.3.6.1.4.1.6486.801.1.2.1.10.6.1.1.2.5.1 |
alaPimdmDenseGroupAddressTypeThe address type of this entry. InetAddressType (INET-ADDRESS-MIB) .1.3.6.1.4.1.6486.801.1.2.1.10.6.1.1.2.5.1.1 |
alaPimdmDenseGroupGrpAddressThe multicast group address that, when combined with
alaPimdmDenseGroupGrpPrefixLength, gives the group prefix for this
entry. The InetAddressType is given by the
alaPimdmDenseGroupAddressType object.
This address object is only significant up to
alaPimdmDenseGroupGrpPrefixLength bits. The remainder of the
address bits are zero. This is especially important for
this index field, which is part of the index of this entry.
Any non-zero bits would signify an entirely different
entry. InetAddress .1.3.6.1.4.1.6486.801.1.2.1.10.6.1.1.2.5.1.2 |
alaPimdmDenseGroupGrpPrefixLengthThe multicast group prefix length that, when combined
with alaPimdmDenseGroupGrpAddress, gives the group prefix for this
entry. The InetAddressType is given by the
alaPimdmDenseGroupAddressType object. If alaPimdmDenseGroupAddressType is
'ipv4' or 'ipv4z', this object must be in the range 4..32.
If alaPimdmDenseGroupGrpAddressType is 'ipv6' or 'ipv6z', this
object must be in the range 8..128. InetAddressPrefixLength .1.3.6.1.4.1.6486.801.1.2.1.10.6.1.1.2.5.1.3 |
alaPimdmDenseGroupOverrideDynamicWhether this dense group configuration will override other
group mappings in this group prefix. If this object is
TRUE, then it will override:
- RP information learned dynamically for groups in this
group prefix.
- RP information configured in alaPimdmDenseGroupTable with
alaPimdmDenseGroupOverrideDynamic set to FALSE.
See pimGroupMappingTable for details.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.6486.801.1.2.1.10.6.1.1.2.5.1.4 |
alaPimdmDenseGroupPrecedenceThe value for pimGroupMappingPrecedence to be used for this
static RP configuration. This allows fine control over
which configuration is overridden by this static
configuration.
If alaPimdmDenseGroupOverrideDynamic is set to TRUE, all dynamic RP
configuration is overridden by this static configuration,
whatever the value of this object.
The absolute values of this object have a significance only
on the local router and do not need to be coordinated with
other routers. A setting of this object may have different
effects when applied to other routers.
Do not use this object unless fine control of static RP
behavior on the local router is required.rw Unsigned32 .1.3.6.1.4.1.6486.801.1.2.1.10.6.1.1.2.5.1.5 |
alaPimdmDenseGroupRowStatusThe status of this row, by which rows in this table can
be created and destroyed.
All writeable objects in this entry can be modified when the
status of this entry is active(1).rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.6486.801.1.2.1.10.6.1.1.2.5.1.6 |
alaPimGlobalConfig OBJECT IDENTIFIER .1.3.6.1.4.1.6486.801.1.2.1.10.6.1.1.3 |
alaPimBfdStatusAdministratively enables/disables PIM
with the BFD protocol on this router.ro Enumeration .1.3.6.1.4.1.6486.801.1.2.1.10.6.1.1.3.1 |
alaPimBfdAllInterfaceStatusAdministratively enables/disables BFD
for all PIM interfaces on this router.ro Enumeration .1.3.6.1.4.1.6486.801.1.2.1.10.6.1.1.3.2 |
alaPimMoFRRStatusAdministratively enables/disables MoFRR
(Multicast only Fast Re-Route) on this router.rw Enumeration .1.3.6.1.4.1.6486.801.1.2.1.10.6.1.1.3.3 |
alaPimMoFRRAllRouteStatusBy default, MoFRR is only applied to multicast
routes that have local clients. Enabling
alaPimMoFRRAllRouteStatus will enable MoFRR
on all routes whether there are local clients
or not. alaPimMoFRRStatus must be enabled for
this to take effect.rw Enumeration .1.3.6.1.4.1.6486.801.1.2.1.10.6.1.1.3.4 |
alaPimInterfaceAugTableExpansion for pimInterfaceTable SEQUENCE OF AlaPimInterfaceAugEntry .1.3.6.1.4.1.6486.801.1.2.1.10.6.1.1.3.5 |
alaPimInterfaceAugEntryAn entry of alaPimInterfaceAugTable AlaPimInterfaceAugEntry .1.3.6.1.4.1.6486.801.1.2.1.10.6.1.1.3.5.1 |
alaPimInterfaceBfdStatusEnables/Disables BFD for particular interfaces of PIM.ro Enumeration .1.3.6.1.4.1.6486.801.1.2.1.10.6.1.1.3.5.1.1 |
alaPimMbrAllSourcesStatusAdministratively enables/disables PIM to notify DVMRP about
the routes to all multicast sources learned instead of just
the directly connected subnets so that these routes can be
advertised in the DVMRP domain via standard DVMRP mechanisms.
This object is only applicable if the router is operating as
a Multicast Border Router.rw Enumeration .1.3.6.1.4.1.6486.801.1.2.1.10.6.1.1.3.6 |
alaPimMbrOperStatusWhether MBR is currently enabled/disabled for PIM.ro Enumeration .1.3.6.1.4.1.6486.801.1.2.1.10.6.1.1.3.7 |
alcatelIND1PIMMIBConformance OBJECT IDENTIFIER .1.3.6.1.4.1.6486.801.1.2.1.10.6.1.2 |
alcatelIND1PIMMIBCompliances OBJECT IDENTIFIER .1.3.6.1.4.1.6486.801.1.2.1.10.6.1.2.1 |
alcatelIND1PIMMIBGroups OBJECT IDENTIFIER .1.3.6.1.4.1.6486.801.1.2.1.10.6.1.2.2 |