ALCATEL-IND1-IPX-MIB
AI MIB Summary
The ALCATEL-IND1-IPX-MIB provides vendor-specific SNMP access to monitor and configure the Internetwork Packet Exchange (IPX) routing subsystem on Alcatel-Lucent network devices. It exposes management objects for IPX routing tables, interface status, and protocol statistics to facilitate the administration of legacy IPX networks.
This module describes an authoritative enterprise-specific Simple Network Management Protocol (SNMP) Management Information Base (MIB):
This is the proprietary MIB for the IPX routing sub-sytem.
The right to make changes in specification and other information contained in this document without prior notice is reserved.
No liability shall be assumed for any incidental, indirect, special, or consequential damages whatsoever arising from or related to this document or the information contained herein.
Vendors, end-users, and other interested parties are granted non-exclusive license to use this specification in connection with management of the products for which it is intended to be used.
Copyright (C) 1995-2007 Alcatel-Lucent ALL RIGHTS RESERVED WORLDWIDE
Main OID:
alcatelIND1IPXMIB.1.3.6.1.4.1.6486.801.1.2.1.10.8.1
65
Objects
Active
Status
4
Dependencies
Imported Objects
Objects
65 total| Object Name |
|---|
alcatelIND1IPXMIBThis module describes an authoritative enterprise-specific Simple
Network Management Protocol (SNMP) Management Information Base (MIB):
This is the proprietary MIB for the IPX routing sub-sytem.
The right to make changes in specification and other information
contained in this document without prior notice is reserved.
No liability shall be assumed for any incidental, indirect, special, or
consequential damages whatsoever arising from or related to this
document or the information contained herein.
Vendors, end-users, and other interested parties are granted
non-exclusive license to use this specification in connection with
management of the products for which it is intended to be used.
Copyright (C) 1995-2007 Alcatel-Lucent
ALL RIGHTS RESERVED WORLDWIDE MODULE-IDENTITY .1.3.6.1.4.1.6486.801.1.2.1.10.8.1 |
alcatelIND1IPXMIBObjects OBJECT IDENTIFIER .1.3.6.1.4.1.6486.801.1.2.1.10.8.1.1 |
alaIpxRoutingGroupIPX routing information. OBJECT IDENTIFIER .1.3.6.1.4.1.6486.801.1.2.1.10.8.1.1.1 |
alaIpxStaticRouteTableThe Static Routes table is used and add entries and extract
information from the static routes configured in the system. SEQUENCE OF IPXStaticRouteEntry .1.3.6.1.4.1.6486.801.1.2.1.10.8.1.1.1.1 |
alaIpxStaticRouteEntryEach entry corresponds to one static route. IPXStaticRouteEntry .1.3.6.1.4.1.6486.801.1.2.1.10.8.1.1.1.1.1 |
alaIpxStaticRouteNetNumThe IPX network number of the route's destination. NetNumber .1.3.6.1.4.1.6486.801.1.2.1.10.8.1.1.1.1.1.1 |
alaIpxStaticRouteNextHopNetThe IPX network number of the router used to
reach the first hop in the static route.rw NetNumber .1.3.6.1.4.1.6486.801.1.2.1.10.8.1.1.1.1.1.2 |
alaIpxStaticRouteNextHopNodeThe IPX node number of the router used to
reach the first hop in the static route.rw HostAddress .1.3.6.1.4.1.6486.801.1.2.1.10.8.1.1.1.1.1.3 |
alaIpxStaticRouteTicksThe delay, in ticks, to reach the route's destination.rw INTEGER .1.3.6.1.4.1.6486.801.1.2.1.10.8.1.1.1.1.1.4 |
alaIpxStaticRouteHopCountThe number of hops necessary to reach the destination.rw INTEGER .1.3.6.1.4.1.6486.801.1.2.1.10.8.1.1.1.1.1.5 |
alaIpxStaticRouteRowStatusThe row status variable, used in accordance to installation
and removal conventions for conceptual rows. The RowStatus of
a currenty active row in the alaIpxStaticRouteTable is constrained
by the operational state of the corresponding static route.
The RowStatus values that are supported are the following:
active: This indicates that the row is active and valid.
createAndGo: This will create the row and activate it.
destroy: This value will deactivate the row and delete from
the system.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.6486.801.1.2.1.10.8.1.1.1.1.1.6 |
alaIpxDefRouteTableThe default route table contains information about
the destinations to which all packets are sent when the
destination network is not known. SEQUENCE OF IPXDefRouteEntry .1.3.6.1.4.1.6486.801.1.2.1.10.8.1.1.1.2 |
alaIpxDefRouteEntryOne table entry per switch for default route. IPXDefRouteEntry .1.3.6.1.4.1.6486.801.1.2.1.10.8.1.1.1.2.1 |
alaIpxDefRouteVlanIdThe VlanId for this filter. If VlanId equals 0, the filter
is applied globally. INTEGER .1.3.6.1.4.1.6486.801.1.2.1.10.8.1.1.1.2.1.1 |
alaIpxDefRouteNetThe IPX network number of the router used to
reach the first hop in the default route.rw NetNumber .1.3.6.1.4.1.6486.801.1.2.1.10.8.1.1.1.2.1.2 |
alaIpxDefRouteNodeThe IPX node number of the router used to
reach the first hop in the default route.rw HostAddress .1.3.6.1.4.1.6486.801.1.2.1.10.8.1.1.1.2.1.3 |
alaIpxDefRouteRowStatusThe row status variable, used in accordance to installation
and removal conventions for conceptual rows. The RowStatus of
a currenty active row in the alaIpxDefRouteTable is constrained
by the operational state of the corresponding default route entry.
The RowStatus values that are supported are the following:
active: This indicates that the row is active and valid.
createAndGo: This will create the row and activate it.
destroy: This value will deactivate the row and delete from
the system.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.6486.801.1.2.1.10.8.1.1.1.2.1.4 |
alaIpxExtMsgTableThe extended RIP and SAP messages table contains information
about which vlans use extended RIP and SAP packets. SEQUENCE OF IPXExtMsgEntry .1.3.6.1.4.1.6486.801.1.2.1.10.8.1.1.1.3 |
alaIpxExtMsgEntryOne table entry per Vlan. IPXExtMsgEntry .1.3.6.1.4.1.6486.801.1.2.1.10.8.1.1.1.3.1 |
alaIpxExtMsgVlanIdThe VlanId for this filter. If VlanId equals 0, the filter
is applied globally. INTEGER .1.3.6.1.4.1.6486.801.1.2.1.10.8.1.1.1.3.1.1 |
alaIpxExtMsgModeIndicates whether extended RIP/SAP
packets are sent and received.rw Enumeration .1.3.6.1.4.1.6486.801.1.2.1.10.8.1.1.1.3.1.2 |
alaIpxExtMsgRowStatusThe row status variable, used in accordance to installation
and removal conventions for conceptual rows. The RowStatus of
a currenty active row in the alaIpxExtMsgTable is constrained
by the operational state of the corresponding watchdog entry.
The RowStatus values that are supported are the following:
active: This indicates that the row is active and valid.
createAndGo: This will create the row and activate it.
destroy: This value will deactivate the row and delete from
the system.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.6486.801.1.2.1.10.8.1.1.1.3.1.3 |
alaIpxFlushFlushes the routing and the SAP tables. The tables will then
be rebuilt from the broadcast messages received from the
networks. Reading this variable is undefinedrw Enumeration .1.3.6.1.4.1.6486.801.1.2.1.10.8.1.1.1.4 |
alaIpxFilterGroupIPX filtering information. OBJECT IDENTIFIER .1.3.6.1.4.1.6486.801.1.2.1.10.8.1.1.2 |
alaIpxRipSapFilterTableThe IPX Rip/Sap Filter Table contains information about
all filters that have been defined. SEQUENCE OF IPXRipSapFilterEntry .1.3.6.1.4.1.6486.801.1.2.1.10.8.1.1.2.1 |
alaIpxRipSapFilterEntryEach entry corresponds to one filter. IPXRipSapFilterEntry .1.3.6.1.4.1.6486.801.1.2.1.10.8.1.1.2.1.1 |
alaIpxRipSapFilterVlanIdThe VlanId for this filter. If VlanId equals 0, the filter
is applied globally. INTEGER .1.3.6.1.4.1.6486.801.1.2.1.10.8.1.1.2.1.1.1 |
alaIpxRipSapFilterTypeThe type of filter. Enumeration .1.3.6.1.4.1.6486.801.1.2.1.10.8.1.1.2.1.1.2 |
alaIpxRipSapFilterNetThe IPX Network Address to filter. A network address
of all 0 's is used to denote All Networks. NetNumber .1.3.6.1.4.1.6486.801.1.2.1.10.8.1.1.2.1.1.3 |
alaIpxRipSapFilterNetMaskThe IPX Network Mask to be used. NetNumber .1.3.6.1.4.1.6486.801.1.2.1.10.8.1.1.2.1.1.4 |
alaIpxRipSapFilterNodeThe IPX node address to filter. A node address
of all 0 's is used to denote All Nodes. HostAddress .1.3.6.1.4.1.6486.801.1.2.1.10.8.1.1.2.1.1.5 |
alaIpxRipSapFilterNodeMaskThe IPX node address mask to be used. HostAddress .1.3.6.1.4.1.6486.801.1.2.1.10.8.1.1.2.1.1.6 |
alaIpxRipSapFilterSvcTypeThe SAP service type on which to filter. The SAP
service types are defined by Novell.A value of
ALL(65535) indicates that all services will be filtered. INTEGER .1.3.6.1.4.1.6486.801.1.2.1.10.8.1.1.2.1.1.7 |
alaIpxRipSapFilterModeThe action defined by this filter. block (1) means
packets matching this filter will be blocked, and
allow(0) means that packets matching this filter
will be allowed.rw Enumeration .1.3.6.1.4.1.6486.801.1.2.1.10.8.1.1.2.1.1.8 |
alaIpxRipSapFilterRowStatusThe row status variable, used in accordance to installation
and removal conventions for conceptual rows. The RowStatus of
a currenty active row in the alaIpxRipSapFilterTable is constrained
by the operational state of the corresponding filter entry.
The RowStatus values that are supported are the following:
active: This indicates that the row is active and valid.
createAndGo: This will create the row and activate it.
destroy: This value will deactivate the row and delete from
the system.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.6486.801.1.2.1.10.8.1.1.2.1.1.10 |
alaIpxWatchdogSpoofTableThe IPX Watchdog Spoofing Table contains information about
all of the current IPX WAN watchdog spoofing entry statuses. SEQUENCE OF IPXWatchdogSpoofEntry .1.3.6.1.4.1.6486.801.1.2.1.10.8.1.1.2.2 |
alaIpxWatchdogSpoofEntryEach entry corresponds to one WAN routing service. IPXWatchdogSpoofEntry .1.3.6.1.4.1.6486.801.1.2.1.10.8.1.1.2.2.1 |
alaIpxWatchdogSpoofVlanIdThe VlanId of the WAN routing service that this entry
applies to. If VlanId equals 0, the filter
is applied globally to all WAN Vlans. INTEGER .1.3.6.1.4.1.6486.801.1.2.1.10.8.1.1.2.2.1.1 |
alaIpxWatchdogSpoofModeThis controls whether the IPX Watchdog Spoofing is
enabled or disabled.When enabled, this routing service
will spoof IPX Watchdog packets.When disabled,
this routing service will not spoof IPX Watchdog packets.rw Enumeration .1.3.6.1.4.1.6486.801.1.2.1.10.8.1.1.2.2.1.2 |
alaIpxWatchdogSpoofRowStatusThe row status variable, used in accordance to installation
and removal conventions for conceptual rows. The RowStatus of
a currenty active row in the alaIpxWatchdogSpoofTable is constrained
by the operational state of the corresponding watchdog entry.
The RowStatus values that are supported are the following:
active: This indicates that the row is active and valid.
createAndGo: This will create the row and activate it.
destroy: This value will deactivate the row and delete from
the system.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.6486.801.1.2.1.10.8.1.1.2.2.1.3 |
alaIpxSerialFilterTableThe IPX Serialization Filtering Table contains information about
all of the current IPX WAN serialization filtering entry statuses. SEQUENCE OF IPXSerialFilterEntry .1.3.6.1.4.1.6486.801.1.2.1.10.8.1.1.2.3 |
alaIpxSerialFilterEntryEach entry corresponds to one WAN routing service. IPXSerialFilterEntry .1.3.6.1.4.1.6486.801.1.2.1.10.8.1.1.2.3.1 |
alaIpxSerialFilterVlanIdThe VlanId of the WAN routing service that this entry
applies to. If VlanId equals 0, the filter
is applied globally to all WAN Vlans. INTEGER .1.3.6.1.4.1.6486.801.1.2.1.10.8.1.1.2.3.1.1 |
alaIpxSerialFilterModeThis controls whether the IPX Serialization Filtering is
enabled or disabled.When enabled, this routing service
will filter IPX Serialization packets.When disabled,
this routing service will not filter IPX Serialization
packets.rw Enumeration .1.3.6.1.4.1.6486.801.1.2.1.10.8.1.1.2.3.1.2 |
alaIpxSerialFilterRowStatusThe row status variable, used in accordance to installation
and removal conventions for conceptual rows. The RowStatus of
a currenty active row in the alaIpxSerialFilterTable is constrained
by the operational state of the corresponding filter entry.
The RowStatus values that are supported are the following:
active: This indicates that the row is active and valid.
createAndGo: This will create the row and activate it.
destroy: This value will deactivate the row and delete from
the system.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.6486.801.1.2.1.10.8.1.1.2.3.1.3 |
alaSpxKeepaliveSpoofTableThe SPX Keepalive Spoofing Table contains information about
all of the current IPX WAN SPX spoofing filtering entry statuses. SEQUENCE OF SPXKeepaliveSpoofEntry .1.3.6.1.4.1.6486.801.1.2.1.10.8.1.1.2.4 |
alaSpxKeepaliveSpoofEntryEach entry corresponds to one WAN routing service. SPXKeepaliveSpoofEntry .1.3.6.1.4.1.6486.801.1.2.1.10.8.1.1.2.4.1 |
alaSpxKeepaliveSpoofVlanIdThe VlanId of the WAN routing service that this entry
applies to. If VlanId equals 0, the filter
is applied globally to all WAN Vlans. INTEGER .1.3.6.1.4.1.6486.801.1.2.1.10.8.1.1.2.4.1.1 |
alaSpxKeepaliveSpoofModeThis controls whether the SPX Keepalive Spoofing is
enabled or disabled.When enabled, this routing service
will spoof SPX Keepalive packets.When disabled,
this routing service will not spoof SPX Keepalive packets.rw Enumeration .1.3.6.1.4.1.6486.801.1.2.1.10.8.1.1.2.4.1.2 |
alaSpxKeepaliveSpoofRowStatusThe row status variable, used in accordance to installation
and removal conventions for conceptual rows. The RowStatus of
a currenty active row in the alaIpxKeepaliveSpoofTable is constrained
by the operational state of the corresponding keepalive entry.
The RowStatus values that are supported are the following:
active: This indicates that the row is active and valid.
createAndGo: This will create the row and activate it.
destroy: This value will deactivate the row and delete from
the system.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.6486.801.1.2.1.10.8.1.1.2.4.1.3 |
alaIpxType20TableThe IPX Type 20 Table contains information about
all of the current Type 20 filtering entry statuses. SEQUENCE OF IPXType20Entry .1.3.6.1.4.1.6486.801.1.2.1.10.8.1.1.2.5 |
alaIpxType20EntryEach entry corresponds to one Virtual LAN. IPXType20Entry .1.3.6.1.4.1.6486.801.1.2.1.10.8.1.1.2.5.1 |
alaIpxType20VlanIdThe VLAN Id of the routing interface that this entry
applies to. If VlanId equals 0, the filter
is applied globally. INTEGER .1.3.6.1.4.1.6486.801.1.2.1.10.8.1.1.2.5.1.1 |
alaIpxType20ModeThis controls whether IPX Type 20 packet are
enabled or disabled.When enabled, this routing interface
will forward Type 20 packets.When disabled,
the packets will not.rw Enumeration .1.3.6.1.4.1.6486.801.1.2.1.10.8.1.1.2.5.1.2 |
alaIpxType20RowStatusThe row status variable, used in accordance to installation
and removal conventions for conceptual rows. The RowStatus of
a currenty active row in the alaIpxType20Table is constrained
by the operational state of the corresponding type 20 entry.
The RowStatus values that are supported are the following:
active: This indicates that the row is active and valid.
createAndGo: This will create the row and activate it.
destroy: This value will deactivate the row and delete from
the system.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.6486.801.1.2.1.10.8.1.1.2.5.1.3 |
alaIpxTimerGroupIPX timer information. OBJECT IDENTIFIER .1.3.6.1.4.1.6486.801.1.2.1.10.8.1.1.3 |
alaIpxTimerTableThe IPX Timer Table contains information about
all of the current Timer adjustments entry statuses. SEQUENCE OF IPXTimerEntry .1.3.6.1.4.1.6486.801.1.2.1.10.8.1.1.3.1 |
alaIpxTimerEntryEach entry corresponds to one Virtual LAN. IPXTimerEntry .1.3.6.1.4.1.6486.801.1.2.1.10.8.1.1.3.1.1 |
alaIpxTimerVlanIdThe VLAN Id of the routing interface that this entry
applies to. If VlanId equals 0, the filter
is applied globally. INTEGER .1.3.6.1.4.1.6486.801.1.2.1.10.8.1.1.3.1.1.1 |
alaIpxTimerSapThis controls whether IPX SAP packet timer duration.rw INTEGER .1.3.6.1.4.1.6486.801.1.2.1.10.8.1.1.3.1.1.2 |
alaIpxTimerRipThis controls whether IPX RIP packet timer duration.rw INTEGER .1.3.6.1.4.1.6486.801.1.2.1.10.8.1.1.3.1.1.3 |
alaIpxTimerRowStatusThe row status variable, used in accordance to installation
and removal conventions for conceptual rows. The RowStatus of
a currenty active row in the alaIpxTimerTable is constrained
by the operational state of the corresponding timer entry.
The RowStatus values that are supported are the following:
active: This indicates that the row is active and valid.
createAndGo: This will create the row and activate it.
destroy: This value will deactivate the row and delete from
the system.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.6486.801.1.2.1.10.8.1.1.3.1.1.4 |
alcatelIND1IPXMIBConformance OBJECT IDENTIFIER .1.3.6.1.4.1.6486.801.1.2.1.10.8.1.2 |
alcatelIND1IPXMIBCompliances OBJECT IDENTIFIER .1.3.6.1.4.1.6486.801.1.2.1.10.8.1.2.1 |
alcatelIND1IPXMIBGroups OBJECT IDENTIFIER .1.3.6.1.4.1.6486.801.1.2.1.10.8.1.2.2 |