ALCATEL-IND1-IPSEC-MIB
AI MIB Summary
The ALCATEL-IND1-IPSEC-MIB provides proprietary SNMP access to monitor and configure IPsec security associations, tunnel states, and cryptographic parameters on Alcatel-Lucent network infrastructure. This module enables the tracking of session establishment failures, packet counters, and SA lifetime metrics for enterprise-grade VPN management.
This module describes an authoritative enterprise-specific Simple Network Management Protocol (SNMP) Management Information Base (MIB):
Proprietary IPsec MIB definitions
The right to make changes in specification and other information contained in this document without prior notice is reserved.
No liability shall be assumed for any incidental, indirect, special, or consequential damages whatsoever arising from or related to this document or the information contained herein.
Vendors, end-users, and other interested parties are granted non-exclusive license to use this specification in connection with management of the products for which it is intended to be used.
Copyright (C) 1995-2010 Alcatel-Lucent ALL RIGHTS RESERVED WORLDWIDE
Main OID:
alcatelIND1IPsecMIB.1.3.6.1.4.1.6486.801.1.2.1.43.1
97
Objects
Active
Status
6
Dependencies
Imported Objects
Objects
97 total| Object Name |
|---|
alcatelIND1IPsecMIBThis module describes an authoritative enterprise-specific Simple
Network Management Protocol (SNMP) Management Information Base (MIB):
Proprietary IPsec MIB definitions
The right to make changes in specification and other information
contained in this document without prior notice is reserved.
No liability shall be assumed for any incidental, indirect, special,
or consequential damages whatsoever arising from or related to this
document or the information contained herein.
Vendors, end-users, and other interested parties are granted
non-exclusive license to use this specification in connection with
management of the products for which it is intended to be used.
Copyright (C) 1995-2010 Alcatel-Lucent
ALL RIGHTS RESERVED WORLDWIDE MODULE-IDENTITY .1.3.6.1.4.1.6486.801.1.2.1.43.1 |
alcatelIND1IPsecMIBObjects OBJECT IDENTIFIER .1.3.6.1.4.1.6486.801.1.2.1.43.1.1 |
alaIPsecConfig OBJECT IDENTIFIER .1.3.6.1.4.1.6486.801.1.2.1.43.1.1.1 |
alaIPsecSecurityKeyTableTable allowing the configuration of the switch's IPsec security key.
The security key is used to encrypt and IPsec related information
retained in permanent storage.
There is always a single row in this table with an index value of 1. SEQUENCE OF AlaIPsecSecurityKeyEntry .1.3.6.1.4.1.6486.801.1.2.1.43.1.1.1.1 |
alaIPsecSecurityKeyEntryThe security key entry. AlaIPsecSecurityKeyEntry .1.3.6.1.4.1.6486.801.1.2.1.43.1.1.1.1.1 |
alaIPsecSecurityKeyIDThe row's identifier. Only one entry is ever present, with an
ID value of 1. Unsigned32 .1.3.6.1.4.1.6486.801.1.2.1.43.1.1.1.1.1.1 |
alaIPsecSecurityKeyCurrentThe current value of the 16-byte IPsec security key. If an attempt
is made to read the value of this object, a zero-length octet
string will be returned.rw OCTET STRING .1.3.6.1.4.1.6486.801.1.2.1.43.1.1.1.1.1.2 |
alaIPsecSecurityKeyNewUsed to set a new 16-byte value for the IPsec security key.
Both alaIPsecSecurityKeyCurrent (with its correct value) and
alaIPsecSecurityKeyNew must be specified in the same SNMP SET
message. If alaIPsecSecurityKeyCurrent is not present, or if
its value is incorrect, the attempt to set a new key will fail.
If an attempt is made to read the value of this object, a zero-length
octet string will be returned.rw OCTET STRING .1.3.6.1.4.1.6486.801.1.2.1.43.1.1.1.1.1.3 |
alaIPsecStatisticsTableTable allowing the IPv6 statistics to be retrieved.deprecated SEQUENCE OF AlaIPsecStatisticsEntry .1.3.6.1.4.1.6486.801.1.2.1.43.1.1.1.2 |
alaIPsecStatisticsEntryThe statistics entry.deprecated AlaIPsecStatisticsEntry .1.3.6.1.4.1.6486.801.1.2.1.43.1.1.1.2.1 |
alaIPsecStatisticsProtocolIP protocol version covered by the IPsec statistics.deprecated Enumeration .1.3.6.1.4.1.6486.801.1.2.1.43.1.1.1.2.1.1 |
alaIPsecStatisticsInSuccessfulNumber of incoming packets requiring IPsec processing
that were successfully handled.rodeprecated Counter32 .1.3.6.1.4.1.6486.801.1.2.1.43.1.1.1.2.1.2 |
alaIPsecStatisticsInPolicyViolationNumber of incoming packets that were dropped because
of policy violations.rodeprecated Counter32 .1.3.6.1.4.1.6486.801.1.2.1.43.1.1.1.2.1.3 |
alaIPsecStatisticsInNoSANumber of incoming packets dropped because no
matching SA was found.rodeprecated Counter32 .1.3.6.1.4.1.6486.801.1.2.1.43.1.1.1.2.1.4 |
alaIPsecStatisticsInUnknownSPINumber of incoming packets dropped because the SPI was
unknown.rodeprecated Counter32 .1.3.6.1.4.1.6486.801.1.2.1.43.1.1.1.2.1.5 |
alaIPsecStatisticsInAHReplayNumber of incoming packets that failed the AH replay
check.rodeprecated Counter32 .1.3.6.1.4.1.6486.801.1.2.1.43.1.1.1.2.1.6 |
alaIPsecStatisticsInESPReplayNumber of incoming packets taht failed the ESP
replay check.rodeprecated Counter32 .1.3.6.1.4.1.6486.801.1.2.1.43.1.1.1.2.1.7 |
alaIPsecStatisticsInAHAuthenticationSuccessNumber of incoming packets that successfully passed
AH authentication.rodeprecated Counter32 .1.3.6.1.4.1.6486.801.1.2.1.43.1.1.1.2.1.8 |
alaIPsecStatisticsInAHAuthenticationFailNumber of incoming packets that failed AH
authentication.rodeprecated Counter32 .1.3.6.1.4.1.6486.801.1.2.1.43.1.1.1.2.1.9 |
alaIPsecStatisticsInESPAuthenticationSuccessNumber of incoming packets that successfully passed
ESP authentication.rodeprecated Counter32 .1.3.6.1.4.1.6486.801.1.2.1.43.1.1.1.2.1.10 |
alaIPsecStatisticsInESPAuthenticationFailNumber of incoming packets that failed ESP
authentication.rodeprecated Counter32 .1.3.6.1.4.1.6486.801.1.2.1.43.1.1.1.2.1.11 |
alaIPsecStatisticsInBadPacketNumber of incoming packets requiring IPsec
processing that were not valid.rodeprecated Counter32 .1.3.6.1.4.1.6486.801.1.2.1.43.1.1.1.2.1.12 |
alaIPsecStatisticsInNoMemoryNumber of incoming IPsec packets dropped because
no memory was available.rodeprecated Counter32 .1.3.6.1.4.1.6486.801.1.2.1.43.1.1.1.2.1.13 |
alaIPsecStatisticsOutSuccessfulNumber of outgoing packets requiring IPsec processing
that were successfully handled.rodeprecated Counter32 .1.3.6.1.4.1.6486.801.1.2.1.43.1.1.1.2.1.14 |
alaIPsecStatisticsOutPolicyViolationNumber of outgoing packets dropped because of a
policy violation.rodeprecated Counter32 .1.3.6.1.4.1.6486.801.1.2.1.43.1.1.1.2.1.15 |
alaIPsecStatisticsOutNoSANumber of outgoing packets dropped because no matching
SA was found.rodeprecated Counter32 .1.3.6.1.4.1.6486.801.1.2.1.43.1.1.1.2.1.16 |
alaIPsecStatisticsOutBadPacketNumber of outgoing packets requiring IPsec processing
that were not valid.rodeprecated Counter32 .1.3.6.1.4.1.6486.801.1.2.1.43.1.1.1.2.1.17 |
alaIPsecStatisticsOutNoMemoryNumber of outgoing IPsec packets dropped because no
memory was available.rodeprecated Counter32 .1.3.6.1.4.1.6486.801.1.2.1.43.1.1.1.2.1.18 |
alaIPsecStatisticsInDiscardedNumber of incoming packets dropped because they matched
a discard policy.rodeprecated Counter32 .1.3.6.1.4.1.6486.801.1.2.1.43.1.1.1.2.1.19 |
alaIPsecStatisticsOutDiscardedNumber of outgoing packets dropped because they matched
a discard policy.rodeprecated Counter32 .1.3.6.1.4.1.6486.801.1.2.1.43.1.1.1.2.1.20 |
alaIPsecSecurityPolicyTableTable allowing the configuration of IPsec security policies. SEQUENCE OF AlaIPsecSecurityPolicyEntry .1.3.6.1.4.1.6486.801.1.2.1.43.1.1.2 |
alaIPsecSecurityPolicyEntryA security policy entry. AlaIPsecSecurityPolicyEntry .1.3.6.1.4.1.6486.801.1.2.1.43.1.1.2.1 |
alaIPsecSecurityPolicyIDA unique identifier for this security policy. When creating a
new policy, a zero value must be specified. An available
policy ID will then be automatically assigned to the policy. Unsigned32 .1.3.6.1.4.1.6486.801.1.2.1.43.1.1.2.1.1 |
alaIPsecSecurityPolicySourceTypeThe type of source address specified. Currently only ipv6(2) is allowed.rw InetAddressType (INET-ADDRESS-MIB) .1.3.6.1.4.1.6486.801.1.2.1.43.1.1.2.1.2 |
alaIPsecSecurityPolicySourceThe source of packets covered by this policy.rw InetAddress (INET-ADDRESS-MIB) .1.3.6.1.4.1.6486.801.1.2.1.43.1.1.2.1.3 |
alaIPsecSecurityPolicySourcePrefixLengthThe number of bits of the source address used to determine
which packets are covered by this policy.
The default value varies depending upon the type of
source address specified:
IPv4 - 32
IPv6 - 128
DNS name - 0 (any other value is ignored)rw IPsecPrefixLength .1.3.6.1.4.1.6486.801.1.2.1.43.1.1.2.1.4 |
alaIPsecSecurityPolicySourcePortThe source port of packets covered by this policy. To
match packets from any port, specify the 0 wildcard value. A
wildcard policy will only be used when there is no exact match
to a destination port in another entry.rw IPsecPortNumber .1.3.6.1.4.1.6486.801.1.2.1.43.1.1.2.1.5 |
alaIPsecSecurityPolicyDestinationTypeThe type of destination address specified. Currently only ipv6(2) is allowed.rw InetAddressType (INET-ADDRESS-MIB) .1.3.6.1.4.1.6486.801.1.2.1.43.1.1.2.1.6 |
alaIPsecSecurityPolicyDestinationThe destination of packets covered by this policy.rw InetAddress (INET-ADDRESS-MIB) .1.3.6.1.4.1.6486.801.1.2.1.43.1.1.2.1.7 |
alaIPsecSecurityPolicyDestinationPrefixLengthThe number of bits of the destination prefix used to determine
which packets are covered by this policy.
The default value varies depending upon the type of
destination address specified:
IPv4 - 32
IPv6 - 128
DNS name - 0 (any other value is ignored)rw IPsecPrefixLength .1.3.6.1.4.1.6486.801.1.2.1.43.1.1.2.1.8 |
alaIPsecSecurityPolicyDestinationPortThe destination port of packets covered by this policy. To
match packets from any port, specify the 0 wildcard value. A
wildcard policy will only be used when there is no exact match
to a destination port in another entry.rw IPsecPortNumber .1.3.6.1.4.1.6486.801.1.2.1.43.1.1.2.1.9 |
alaIPsecSecurityPolicyULProtocolThe upper-layer protocol of packets covered by this policy.
To match all protocols, specify the 255 wildcard value. A wildcard
policy will only be used when there is no exact match to the protocol
value specified in another entry.rw IPsecULProtocol .1.3.6.1.4.1.6486.801.1.2.1.43.1.1.2.1.10 |
alaIPsecSecurityPolicyICMPv6TypeIf the upper-layer protocol is ICMPv6, an ICMPv6 type value may
be specified to restrict the policy to a specific packet type.
To match all ICMPv6 packets, the 0 wildcard value should be
specified.rw Integer32 .1.3.6.1.4.1.6486.801.1.2.1.43.1.1.2.1.11 |
alaIPsecSecurityPolicyDirectionThe direction of traffic covered by this policy.rw Enumeration .1.3.6.1.4.1.6486.801.1.2.1.43.1.1.2.1.12 |
alaIPsecSecurityPolicyNameA name for this policy.rw SnmpAdminString .1.3.6.1.4.1.6486.801.1.2.1.43.1.1.2.1.13 |
alaIPsecSecurityPolicyDescriptionA detailed description of this policy.rw IPsecDescription .1.3.6.1.4.1.6486.801.1.2.1.43.1.1.2.1.14 |
alaIPsecSecurityPolicyActionThe action to take on traffic covered by this policy.
discard(0) means that all traffic covered by the policy
will be discarded.
none(1) means that no IPsec processing will be done on
the traffic covered by this policy.
ipsec(2) means that IPsec processing will take place on
the traffic. One or more rules should be defined in the
IPsec Rule Table. If no rules are defined processing
is identical to none(0) being specified.rw Enumeration .1.3.6.1.4.1.6486.801.1.2.1.43.1.1.2.1.15 |
alaIPsecSecurityPolicyAdminStateAllows a policy to be administratively enabled or
disabled.rw IPsecAdminState .1.3.6.1.4.1.6486.801.1.2.1.43.1.1.2.1.16 |
alaIPsecSecurityPolicyOperationalStateThe operational state of this policy.ro IPsecOperationalState .1.3.6.1.4.1.6486.801.1.2.1.43.1.1.2.1.17 |
alaIPsecSecurityPolicyPriorityThe priority for this policy. When traffic would be covered by
multiple policies the policy with the highest priority value is
used. If two policies have the same priority, the one configured
first has precedence.rw Integer32 .1.3.6.1.4.1.6486.801.1.2.1.43.1.1.2.1.18 |
alaIPsecSecurityPolicyRowStatusUsed to control the addition and removal of security
policy entries.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.6486.801.1.2.1.43.1.1.2.1.19 |
alaIPsecSecurityPolicyRuleTableTable allowing the configuration of the IPsec rules for
a security policy. SEQUENCE OF AlaIPsecSecurityPolicyRuleEntry .1.3.6.1.4.1.6486.801.1.2.1.43.1.1.3 |
alaIPsecSecurityPolicyRuleEntryA security policy entry. AlaIPsecSecurityPolicyRuleEntry .1.3.6.1.4.1.6486.801.1.2.1.43.1.1.3.1 |
alaIPsecSecurityPolicyRuleIndexIndex specifying the order in which multiple rules for
the same security policy will be applied. Rules are
indexed by the order in which they are applied to the
original payload.
For example, for a security policy where an IPv6 payload
should be protected by an ESP header, which should be protected
by an AH header, there would be two Rule Table entries.
The ESP entry would have an index of 1 (first rule applied
to the payload). The AH entry would have an index of 2
(second rule applied). Unsigned32 .1.3.6.1.4.1.6486.801.1.2.1.43.1.1.3.1.1 |
alaIPsecSecurityPolicyRuleProtocolIndicates the type of header required by the rule.rw Enumeration .1.3.6.1.4.1.6486.801.1.2.1.43.1.1.3.1.2 |
alaIPsecSecurityPolicyRuleModeThe mode in which the rule's protocol is running. At present,
only transport(1) is allowed. Until tunnel mode is supported,
transport(1) will be treated as the default value.rw Enumeration .1.3.6.1.4.1.6486.801.1.2.1.43.1.1.3.1.3 |
alaIPsecSecurityPolicyRuleRowStatusUsed to control the addition and removal of security
policy IPsec rule entries.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.6486.801.1.2.1.43.1.1.3.1.4 |
alaIPsecSAConfigTableTable allowing the manual configuration of Security
Associations in the Security Association Database (SAD). SEQUENCE OF AlaIPsecSAConfigEntry .1.3.6.1.4.1.6486.801.1.2.1.43.1.1.4 |
alaIPsecSAConfigEntryManually configured security association (SA) parameters. AlaIPsecSAConfigEntry .1.3.6.1.4.1.6486.801.1.2.1.43.1.1.4.1 |
alaIPsecSAConfigIDA unique identifier for this manually configured SA.
When creating a new SA, a zero value must be specified.
An available ID will then be automatically assigned to
the SA. Unsigned32 .1.3.6.1.4.1.6486.801.1.2.1.43.1.1.4.1.1 |
alaIPsecSAConfigTypeThe type of this SA: AH or ESP. Once set,
the type may not be changed.rw IPsecSAType .1.3.6.1.4.1.6486.801.1.2.1.43.1.1.4.1.2 |
alaIPsecSAConfigSourceTypeThe type of source address specified. Currently only ipv6(2) is allowed.rw InetAddressType (INET-ADDRESS-MIB) .1.3.6.1.4.1.6486.801.1.2.1.43.1.1.4.1.3 |
alaIPsecSAConfigSourceThe source of packets covered by this SA.rw InetAddress (INET-ADDRESS-MIB) .1.3.6.1.4.1.6486.801.1.2.1.43.1.1.4.1.4 |
alaIPsecSAConfigDestinationTypeThe type of destination address specified. Currently only ipv6(2) is allowed.rw InetAddressType (INET-ADDRESS-MIB) .1.3.6.1.4.1.6486.801.1.2.1.43.1.1.4.1.5 |
alaIPsecSAConfigDestinationThe destination of packets covered by this SA.rw InetAddress (INET-ADDRESS-MIB) .1.3.6.1.4.1.6486.801.1.2.1.43.1.1.4.1.6 |
alaIPsecSAConfigSPIThe Security Parameters Index (SPI) of this SA.rw Unsigned32 .1.3.6.1.4.1.6486.801.1.2.1.43.1.1.4.1.7 |
alaIPsecSAConfigNameThe name of this manually configured SA.rw SnmpAdminString .1.3.6.1.4.1.6486.801.1.2.1.43.1.1.4.1.8 |
alaIPsecSAConfigDescriptionA detailed description for the manually created IPsec SA.rw IPsecDescription .1.3.6.1.4.1.6486.801.1.2.1.43.1.1.4.1.9 |
alaIPsecSAConfigEncryptionAlgorithmFor an ESP SA, defines the encryption algorithm to be used.
null(11) should be specified if ESP is being used for integrity
only. If null(11) is specified,
alaIPsecSAConfigAuthenticationAlgorithm may not be none(0).
aesctr(13) is not valid for manually configured SAs.
The value of this object is none(0) for AH SAs.rw IPsecESPAlgorithm .1.3.6.1.4.1.6486.801.1.2.1.43.1.1.4.1.10 |
alaIPsecSAConfigEncryptionKeyLengthFor those algorithms where multiple key lengths are supported,
specifies the key length to be used. Zero may be specified to
use the default key length.rw Unsigned32 UNITS "bits" .1.3.6.1.4.1.6486.801.1.2.1.43.1.1.4.1.11 |
alaIPsecSAConfigAuthenticationAlgorithmDefines the authentication algorithm to be used.
For ESP SAs, none(0) may be specified for encryption-only ESP.
For ESP integrity-only, ESP integrity and encryption, or for
AH SAs, hmacmd5(2), hmacsha1(3), or aesxcbcmac(9) must
be specified.rw IPsecAHAlgorithm .1.3.6.1.4.1.6486.801.1.2.1.43.1.1.4.1.12 |
alaIPsecSAConfigAdminStateAllows a manually configured SA to be administratively enabled
or disabled.rw IPsecAdminState .1.3.6.1.4.1.6486.801.1.2.1.43.1.1.4.1.13 |
alaIPsecSAConfigOperationalStateThe operational state of the manually configured SA.ro IPsecOperationalState .1.3.6.1.4.1.6486.801.1.2.1.43.1.1.4.1.14 |
alaIPsecSAConfigRowStatusUsed to control the addition and removal of manually configured
IPsec SAs.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.6486.801.1.2.1.43.1.1.4.1.15 |
alaIPsecKeyTableTable used to configure the keys used by manually
configured Security Associations in the IPsec Security
Association Configuration table. SEQUENCE OF AlaIPsecKeyEntry .1.3.6.1.4.1.6486.801.1.2.1.43.1.1.5 |
alaIPsecKeyEntryAn IPsec key. Keys in the table must be uniquely
identified by the combination of key type and key name.
However, since the key name can be up to 255 characters,
beyond the 128-element size limit for SNMP index objects,
the key ID is used to uniquely identify a key for SNMP
access. AlaIPsecKeyEntry .1.3.6.1.4.1.6486.801.1.2.1.43.1.1.5.1 |
alaIPsecKeyIDA unique identifier for this key. When creating a
new key, a zero value must be specified. An available
ID will then be automatically assigned to the key. Unsigned32 .1.3.6.1.4.1.6486.801.1.2.1.43.1.1.5.1.1 |
alaIPsecKeyTypeIndicates if the key is to be used for encryption or
authentication by a SA. Once a key is created, its type
may not be changed.rw Enumeration .1.3.6.1.4.1.6486.801.1.2.1.43.1.1.5.1.2 |
alaIPsecKeyNameThe name of the key.
For manually-configured SA keys, the name is limited to
a maximum length of 20 characters and should correspond
to an entry in the alaIPsecSAConfigTable.
The key name may not be changed once a key is created.rw OCTET STRING .1.3.6.1.4.1.6486.801.1.2.1.43.1.1.5.1.3 |
alaIPsecKeyThe key value. The value specified must match the required
key length for the algorithm using the key. If
an attempt is made to read the value of this object a
zero-length octet string will be returned.rw OCTET STRING .1.3.6.1.4.1.6486.801.1.2.1.43.1.1.5.1.4 |
alaIPsecKeyEncryptedIf true, the key value is specified in AOS encrypted form.
For example, keys being restored from the configuration file.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.6486.801.1.2.1.43.1.1.5.1.5 |
alaIPsecKeyRowStatusUsed to control the addition and removal of keys.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.6486.801.1.2.1.43.1.1.5.1.6 |
alaIPsecErrorsTableTable allowing retrieval of the IPsec error counters. SEQUENCE OF AlaIPsecErrorsEntry .1.3.6.1.4.1.6486.801.1.2.1.43.1.1.6 |
alaIPsecErrorsEntryThe error counters entry. AlaIPsecErrorsEntry .1.3.6.1.4.1.6486.801.1.2.1.43.1.1.6.1 |
alaIPsecErrorsProtocolIP protocol version covered by the IPsec error counters. Enumeration .1.3.6.1.4.1.6486.801.1.2.1.43.1.1.6.1.1 |
alaIPsecErrorsInPolicyViolationNumber of incoming packets that were dropped because
of policy violations.ro Counter32 .1.3.6.1.4.1.6486.801.1.2.1.43.1.1.6.1.2 |
alaIPsecErrorsInNoSANumber of incoming packets dropped because no
matching SA was found.ro Counter32 .1.3.6.1.4.1.6486.801.1.2.1.43.1.1.6.1.3 |
alaIPsecErrorsInReplayNumber of incoming packets that failed a replay check.ro Counter32 .1.3.6.1.4.1.6486.801.1.2.1.43.1.1.6.1.4 |
alaIPsecErrorsInAuthenticationFailNumber of incoming packets that failed authentication.ro Counter32 .1.3.6.1.4.1.6486.801.1.2.1.43.1.1.6.1.5 |
alaIPsecErrorsInDiscardedNumber of incoming packets dropped because they matched
a discard policy.ro Counter32 .1.3.6.1.4.1.6486.801.1.2.1.43.1.1.6.1.6 |
alaIPsecErrorsInOtherNumber of incoming packets dropped for a reason not
otherwise counted.ro Counter32 .1.3.6.1.4.1.6486.801.1.2.1.43.1.1.6.1.7 |
alaIPsecErrorsOutNoSANumber of outgoing packets dropped because no matching
SA was found.ro Counter32 .1.3.6.1.4.1.6486.801.1.2.1.43.1.1.6.1.8 |
alaIPsecErrorsOutDiscardedNumber of outgoing packets dropped because they matched
a discard policy.ro Counter32 .1.3.6.1.4.1.6486.801.1.2.1.43.1.1.6.1.9 |
alaIPsecErrorsOutOtherNumber of outgoing packets dropped for a reason not
otherwise counted.ro Counter32 .1.3.6.1.4.1.6486.801.1.2.1.43.1.1.6.1.10 |
alcatelIND1IPsecMIBConformance OBJECT IDENTIFIER .1.3.6.1.4.1.6486.801.1.2.1.43.1.2 |
alcatelIND1IPsecMIBCompliances OBJECT IDENTIFIER .1.3.6.1.4.1.6486.801.1.2.1.43.1.2.1 |
alcatelIND1IPsecMIBGroups OBJECT IDENTIFIER .1.3.6.1.4.1.6486.801.1.2.1.43.1.2.2 |