ALCATEL-IND1-DOT3-OAM-MIB
AI MIB Summary
The ALCATEL-IND1-DOT3-OAM-MIB enables SNMP-based monitoring of Ethernet in the First Mile (EFM) Operations, Administration, and Maintenance (OAM) parameters on Alcatel-Lucent "Birds of Prey" line cards, specifically tracking link fault management (LTM/FTM) states, remote defect indications (RDI), and loopback control status.
This module describes an authoritative enterprise- specific Simple Network Management Protocol (SNMP) Management Information Base (MIB):
For the Birds Of Prey Product Line Ethernet in First Mile OAM.
The right to make changes in specification and other information contained in this document without prior notice is reserved.
No liability shall be assumed for any incidental, indirect, special, or consequential damages whatsoever arising from or related to this document or the information contained herein.
Vendors, end-users, and other interested parties are granted non-exclusive license to use this specification in connection with management of the products for which it is intended to be used.
Copyright (C) 1995-2002 Alcatel Internetworking, Incorporated ALL RIGHTS RESERVED WORLDWIDE
Main OID:
alcatelIND1Dot3OamMIB.1.3.6.1.4.1.6486.801.1.2.1.52.1
52
Objects
Active
Status
6
Dependencies
Imported Objects
Objects
52 total| Object Name |
|---|
alcatelIND1Dot3OamMIBThis module describes an authoritative enterprise-
specific Simple Network Management Protocol (SNMP) Management
Information Base (MIB):
For the Birds Of Prey Product Line
Ethernet in First Mile OAM.
The right to make changes in specification and other information
contained in this document without prior notice is reserved.
No liability shall be assumed for any incidental, indirect,
special, or consequential damages whatsoever arising from or
related to this document or the information contained herein.
Vendors, end-users, and other interested parties are granted
non-exclusive license to use this specification in connection with
management of the products for which it is intended to be used.
Copyright (C) 1995-2002 Alcatel Internetworking, Incorporated
ALL RIGHTS RESERVED WORLDWIDE MODULE-IDENTITY .1.3.6.1.4.1.6486.801.1.2.1.52.1 |
IMPORTSThis module describes an authoritative enterprise-
specific Simple Network Management Protocol (SNMP) Management
Information Base (MIB):
For the Birds Of Prey Product Line
Ethernet in First Mile OAM.
The right to make changes in specification and other information
contained in this document without prior notice is reserved.
No liability shall be assumed for any incidental, indirect,
special, or consequential damages whatsoever arising from or
related to this document or the information contained herein.
Vendors, end-users, and other interested parties are granted
non-exclusive license to use this specification in connection with
management of the products for which it is intended to be used.
Copyright (C) 1995-2002 Alcatel Internetworking, Incorporated
ALL RIGHTS RESERVED WORLDWIDE Unknown .1.3.6.1.4.1.6486.801.1.2.1.52.1 |
alcatelIND1Dot3OamNotificationsBranch for 802.3ah OAM Notifications. OBJECT IDENTIFIER .1.3.6.1.4.1.6486.801.1.2.1.52.1.0 |
alaDot3OamThresholdEventClearA alaDot3OamThresholdEventClear notification is sent when a local or
remote threshold crossing event is recovered.
The OAM entity can be derived from extracting the ifIndex from
the variable bindings. The objects in the notification
correspond to the values in a row instance in the
dot3OamEventLogTable. NOTIFICATION-TYPE .1.3.6.1.4.1.6486.801.1.2.1.52.1.0.1 |
alaDot3OamNonThresholdEventClearA alaDot3OamNonThresholdEventClear notification is sent when a local
or remote non-threshold crossing event is recovered.
The OAM entity can be derived from extracting the ifIndex from
the variable bindings. The objects in the notification
correspond to the values in a row instance of the
dot3OamEventLogTable. NOTIFICATION-TYPE .1.3.6.1.4.1.6486.801.1.2.1.52.1.0.2 |
alcatelIND1Dot3OamMIBObjectsBranch For 802.3ah OAM Objects. OBJECT IDENTIFIER .1.3.6.1.4.1.6486.801.1.2.1.52.1.1 |
alaDot3OamStatusThe administrative status requested by management for
802.3ah. The value enabled(1) indicates that 802.3ah should
be enabled on this device, on all ports for which it has
not been specifically disabled. When disabled(2), 802.3ah
is disabled on all ports and all 802.3ah packets will be
dropped. A transition from disabled(2) to enabled(1) will
cause a reset of all 802.3ah state machines on all ports.rw Enumeration .1.3.6.1.4.1.6486.801.1.2.1.52.1.1.1 |
alaDot3OamGlobalClearStatsDefines the global clear statistics control for Dot3OAM.
The value reset (1) indicates that clear all statistic counters
related to all ports in the system. By default, this object
contains a zero value.rw Enumeration .1.3.6.1.4.1.6486.801.1.2.1.52.1.1.2 |
alaDot3OamGlobalClearEventLogsDefines the global clear event logs control for Dot3OAM.
The value reset (1) indicates that clear all event logs
related to all ports in the system. By default, this object
contains a zero value.rw Enumeration .1.3.6.1.4.1.6486.801.1.2.1.52.1.1.3 |
alaDot3OamGlobalClearVariableTransactionsDefines the global clear variable transactions control for
Dot3OAM. The value reset (1) indicates that clear all
transactions related to all ports in the system. By default,
this object contains a zero value.rw Enumeration .1.3.6.1.4.1.6486.801.1.2.1.52.1.1.4 |
alaDot3OamMultiplePduCountThis object is used to set the number of PDUs that will be
sent, when OAM needs to send multiple event notification PDUs.rw INTEGER .1.3.6.1.4.1.6486.801.1.2.1.52.1.1.5 |
alaDot3OamPortConfig OBJECT IDENTIFIER .1.3.6.1.4.1.6486.801.1.2.1.52.1.1.8 |
alaDot3OamTableThis table contains the primary controls and status for the
OAM capabilities of an Ethernet like interface. There will be
one row in this table for each Ethernet like interface in the
system that supports the OAM functions defined in [802.3ah]. SEQUENCE OF AlaDot3OamEntry .1.3.6.1.4.1.6486.801.1.2.1.52.1.1.8.1 |
alaDot3OamEntryAn entry in the table, containing information on the Ethernet
OAM function for a single Ethernet like interface. Entries in
the table are created automatically for each interface
supporting Ethernet OAM. The status of the row entry can be
determined from dot3OamOperStatus.
A alaDot3OamEntry is indexed in the alaDot3OamTable by the
ifIndex object of the Interfaces MIB. AlaDot3OamEntry .1.3.6.1.4.1.6486.801.1.2.1.52.1.1.8.1.1 |
alaDot3OamKeepAliveIntervalThis object is used to set the timer in seconds to restart the
discovery process if no PDUs are received in this time frame.rw Integer32 .1.3.6.1.4.1.6486.801.1.2.1.52.1.1.8.1.1.1 |
alaDot3OamHelloIntervalThis object is used to set the interval between two OAMPDUsrw Integer32 .1.3.6.1.4.1.6486.801.1.2.1.52.1.1.8.1.1.2 |
alaDot3OamNextTransactionIdThis object is used to fetch the next available transaction id
required for MIB variable retrieval requests on this interface.
To read the remote entity's MIB variables, a unique transaction
id is generated for each request. The administrator first needs
to get the next available transaction id for the interface, and
provide this as index to the alaDot3OamRetrieveRequestTable.ro Integer32 .1.3.6.1.4.1.6486.801.1.2.1.52.1.1.8.1.1.3 |
alaDot3OamPortLoopbackControl OBJECT IDENTIFIER .1.3.6.1.4.1.6486.801.1.2.1.52.1.1.9 |
alaDot3OamLoopbackTableThis table contains controls for the loopback state of the
local link as well as indicating the status of the loopback
function. There is one entry in this table for each entry in
dot3OamTable that supports loopback functionality (where
dot3OamFunctionsSupported includes the loopbackSupport bit
set). SEQUENCE OF AlaDot3OamLoopbackEntry .1.3.6.1.4.1.6486.801.1.2.1.52.1.1.9.1 |
alaDot3OamLoopbackEntryAn entry in the table, containing information on the L1 ping.
One record/entry shall be maintained per interface. This record
shall be automatically created when L1 ping is initiated for the
first time on the interface. Subsequent ping operations shall
replace the record. Loopback capabilities of the interface can
be determined from the dot3OamLoopbackStatus object. AlaDot3OamLoopbackEntry .1.3.6.1.4.1.6486.801.1.2.1.52.1.1.9.1.1 |
alaDot3OamPortL1PingFramesConfThis object is used to set the number of frames to be transmitted
from the interface during L1 ping.rw Integer32 .1.3.6.1.4.1.6486.801.1.2.1.52.1.1.9.1.1.1 |
alaDot3OamPortL1PingFramesDelayThis object is used to set the delay between two
frames transmitted during L1 ping.rw Integer32 .1.3.6.1.4.1.6486.801.1.2.1.52.1.1.9.1.1.2 |
alaDot3OamPortL1PingStatusThis object is used to start the L1 ping operation. Operator
can set only start(1) value and setting of start(1) value is not valid
if object value is start(1) or running(2).
Whenever efm gets enabled on any port, this object has default(0) value.
Default(0) value implies that loopback session has not been started even
for a single time. Running(2) is corresponding to the state, when L1 ping
is going on, operationSuccessful(3) is corresponding to the state, when L1
ping operation is done successfully. operationUnsuccessful(4) is corresponding
to state when operation gets failed due to some reason.rw Enumeration .1.3.6.1.4.1.6486.801.1.2.1.52.1.1.9.1.1.3 |
alaDot3OamPortL1PingFramesSentThis object is used to keep the actual frames sent during
last L1 ping operation.ro Counter32 .1.3.6.1.4.1.6486.801.1.2.1.52.1.1.9.1.1.4 |
alaDot3OamPortL1PingFramesReceivedThis object is used to keep the number of frames received
during last L1 ping operation.ro Counter32 .1.3.6.1.4.1.6486.801.1.2.1.52.1.1.9.1.1.5 |
alaDot3OamPortL1PingAverageRoundTripDelayThis object is used to keep the average delay taken by frames
during last L1 ping.ro Integer32 .1.3.6.1.4.1.6486.801.1.2.1.52.1.1.9.1.1.6 |
alaDot3OamPortStats OBJECT IDENTIFIER .1.3.6.1.4.1.6486.801.1.2.1.52.1.1.10 |
alaDot3OamStatsTableThis table contains statistics for the OAM function on a
particular Ethernet like interface. There is an entry in the
table for every entry in the dot3OamStatsTable.
The counters in this table are defined as 32-bit entries to
match the counter size as defined in [802.3ah]. Given the OA
protocol is a slow protocol, the counters increment at a slow
rate. SEQUENCE OF AlaDot3OamStatsEntry .1.3.6.1.4.1.6486.801.1.2.1.52.1.1.10.1 |
alaDot3OamStatsEntryAn entry in the table, containing statistics information on
the Ethernet OAM function for a single Ethernet like
interface. Entries are automatically created for every entry
in the dot3OamStatsTable. Counters are maintained across
transitions in dot3OamOperStatus. AlaDot3OamStatsEntry .1.3.6.1.4.1.6486.801.1.2.1.52.1.1.10.1.1 |
alaDot3OamPortClearStatsReset all statistics parameters corresponding to this port
By default, this objects contains a zero value.rw Enumeration .1.3.6.1.4.1.6486.801.1.2.1.52.1.1.10.1.1.1 |
alaDot3OamPortEventLogs OBJECT IDENTIFIER .1.3.6.1.4.1.6486.801.1.2.1.52.1.1.11 |
alaDot3OamEventLogTableThis table records a history of the events that have occurred
at the Ethernet OAM level. These events can include locally
detected events, which may result in locally generated
OAMPDUs, and remotely detected events, which are detected by
the OAM peer entity and signaled to the local entity via
Ethernet OAM. Ethernet OAM events can be signaled by Event
Notification OAMPDUs or by the flags field in any OAMPDU. SEQUENCE OF AlaDot3OamEventLogEntry .1.3.6.1.4.1.6486.801.1.2.1.52.1.1.11.1 |
alaDot3OamEventLogEntryAn entry in the dot3OamEventLogTable. Entries are
automatically created whenever Ethernet OAM events occur at
the local OAM entity, and when Event Notification OAMPDUs are
received at the local OAM entity (indicating events have
occurred at the peer OAM entity). The size of the table is
implementation dependent, but when the table becomes full,
older events are automatically deleted to make room for newer
events. The table index dot3OamEventLogIndex increments for
each new entry, and when the maximum value is reached the
value restarts at zero. AlaDot3OamEventLogEntry .1.3.6.1.4.1.6486.801.1.2.1.52.1.1.11.1.1 |
alaDot3OamPortClearEventLogsReset all event logs corresponding to this port
By default, this objects contains a zero value.rw Enumeration .1.3.6.1.4.1.6486.801.1.2.1.52.1.1.11.1.1.1 |
alaDot3OamRetrieveRequest OBJECT IDENTIFIER .1.3.6.1.4.1.6486.801.1.2.1.52.1.1.12 |
alaDot3OamRetrieveRequestTableA table containing MIB variable retrieval request
information SEQUENCE OF AlaDot3OamRetrieveRequestEntry .1.3.6.1.4.1.6486.801.1.2.1.52.1.1.12.1 |
alaDot3OamRetrieveRequestEntryA 802.3ah MIB variable retrieval request entry. AlaDot3OamRetrieveRequestEntry .1.3.6.1.4.1.6486.801.1.2.1.52.1.1.12.1.1 |
alaDot3OamTransactionIdThis object is used to set the available transaction id for
retrieving the remote MIB variable for this interface. The
value for this is obtained from alaDot3OamNextTransactionId,
which is part of alaDot3OamTable. Integer32 .1.3.6.1.4.1.6486.801.1.2.1.52.1.1.12.1.1.1 |
alaDot3OamVariableRequestBranchThis object is used to set the branch to reference the MIB
object to be retrieved. This is set to attribute, package or
object depending upon the request for getting the MIB variables. Enumeration .1.3.6.1.4.1.6486.801.1.2.1.52.1.1.12.1.1.2 |
alaDot3OamVariableRequestLeafThis object is used to set the leaf to reference the MIB
object to be retrieved. Integer32 .1.3.6.1.4.1.6486.801.1.2.1.52.1.1.12.1.1.3 |
alaDot3OamVariableRequestRetrieveStatusThis object is used to check the status of a MIB request,
Active means that the request is currently in progress),
failed means that the request has failed, and success
means that the request returned successfully.ro Enumeration .1.3.6.1.4.1.6486.801.1.2.1.52.1.1.12.1.1.4 |
alaDot3OamVariableRequestRowStatusRow Status for initiating a MIB retrieval request.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.6486.801.1.2.1.52.1.1.12.1.1.5 |
alaDot3OamPortClearVariableTransactionsReset all variable transactions corresponding to this port
By default, this objects contains a zero value.rw Enumeration .1.3.6.1.4.1.6486.801.1.2.1.52.1.1.12.1.1.6 |
alaDot3OamRetrieveResponse OBJECT IDENTIFIER .1.3.6.1.4.1.6486.801.1.2.1.52.1.1.13 |
alaDot3OamRetrieveResponseTableA table containing MIB variable retrieval response
information SEQUENCE OF AlaDot3OamRetrieveResponseEntry .1.3.6.1.4.1.6486.801.1.2.1.52.1.1.13.1 |
alaDot3OamRetrieveResponseEntryA 802.3ah MIB variable retrieval response entry. AlaDot3OamRetrieveResponseEntry .1.3.6.1.4.1.6486.801.1.2.1.52.1.1.13.1.1 |
alaDot3OamVariableResponseBranchThe branch to reference the MIB object retrieved. Enumeration .1.3.6.1.4.1.6486.801.1.2.1.52.1.1.13.1.1.1 |
alaDot3OamVariableResponseLeafThe leaf to reference the MIB object retrieved. Integer32 .1.3.6.1.4.1.6486.801.1.2.1.52.1.1.13.1.1.2 |
alaDot3OamVariableResponseValueThe value of the retrived attribute.ro DisplayString .1.3.6.1.4.1.6486.801.1.2.1.52.1.1.13.1.1.3 |
alcatelIND1Dot3OamMIBConformanceBranch for 802.3ah Module MIB Subsystem Conformance Information. OBJECT IDENTIFIER .1.3.6.1.4.1.6486.801.1.2.1.52.1.2 |
alcatelIND1Dot3OamMIBGroupsBranch for 802.3ah Module MIB Subsystem Units of Conformance. OBJECT IDENTIFIER .1.3.6.1.4.1.6486.801.1.2.1.52.1.2.1 |
alcatelIND1Dot3OamMIBCompliancesBranch for 802.3ah Module MIB Subsystem Compliance Statements. OBJECT IDENTIFIER .1.3.6.1.4.1.6486.801.1.2.1.52.1.2.2 |