Home/Catalog/ALCATEL-IND1-CHASSIS-MIB

ALCATEL-IND1-CHASSIS-MIB

AI MIB Summary

The ALCATEL-IND1-CHASSIS-MIB extends the IETF Entity MIB to monitor physical chassis-level attributes for Alcatel-Lucent Birds of Prey product lines, specifically tracking hardware objects such as slot status, power supply states, and fan module health that fall outside standard IETF definitions.

This module describes an authoritative enterprise-specific Simple etwork Management Protocol (SNMP) Management Information Base (MIB): For the Birds Of Prey Product Line, this is the Chassis Supervision Chassis MIB for managing physical chassis objects not covered in the IETF Entity MIB (rfc 2737). The right to make changes in specification and other information contained in this document without prior notice is reserved. No liability shall be assumed for any incidental, indirect, special, or consequential damages whatsoever arising from or related to this document or the information contained herein. Vendors, end-users, and other interested parties are granted non-exclusive license to use this specification in connection with management of the products for which it is intended to be used. Copyright (C) 1995-2007 Alcatel-Lucent ALL RIGHTS RESERVED WORLDWIDE
Main OID:
alcatelIND1ChassisMIB.1.3.6.1.4.1.6486.801.1.1.1.3.1
219
Objects
Active
Status
6
Dependencies

Imported Objects

SNMPv2-SMI
ENTITY-MIB
ALCATEL-IND1-BASE
SNMP-FRAMEWORK-MIB
SNMPv2-TC
SNMPv2-CONF

Objects

219 total
Object Name
alcatelIND1ChassisPhysMIBObjectsBranch For Chassis Supervision Chassis Physical MIB Subsystem Managed Objects.
OBJECT IDENTIFIER
.1.3.6.1.4.1.6486.801.1.1.1.1.1
chasEntPhysicalTableThis table contains one row per physical entity. It is an extension for the entity physical table (rfc 2737) that is instantiated for every physical entity object. The fields are not always significant for every object.
SEQUENCE OF ChasEntPhysicalEntry
.1.3.6.1.4.1.6486.801.1.1.1.1.1.1
chasEntPhysicalEntryInformation about a particular physical entity.
ChasEntPhysicalEntry
.1.3.6.1.4.1.6486.801.1.1.1.1.1.1.1
chasEntPhysAdminStatusAll modules (even empty slots) are in unknown state when the chassis first powers up. Chassis status possible value: powerOn <=> powered up Control Module possible value: powerOn <=> CM up and running reset <=> CM reset takeover <=> Secondary CM takes over resetAll <=> resets the whole switch vcTakeover <=> Reloads master chassis from the current working directory, which initiates a VC takeover. vcResetAll <=> resets entire VC. NI status possible value: powerOn <=> NI is either powered (up or down) or waiting to be powered whenever more power is available. This admin status has not full meaning without chasEntPhysOperStatus powerOff <=> NI down and unpowered and NI will not be powered until user requests it, a failover happens or a reboot happens reset <=> NI reset FABRIC status possible value: powerOn <=> FABRIC is powered powerOff <=> FABRIC is unpowered standby <=> FABRIC is powered and requested to be redundant (inactive) Daughter board status possible value: powerOn <=> DB up and running reset <=> DB reset (TO BE CONFIRMED) Power supply status possible value: powerOn <=> PS uprw
Enumeration
.1.3.6.1.4.1.6486.801.1.1.1.1.1.1.1.1
chasEntPhysOperStatusAll modules (even empty slots) are in unknown state when the chassis first powers up. Chassis status possible value : up <=> powered up Control Module possible value : notPresent <=> CM not present up <=> CM up and running down <=> CM down and powered secondary <=> CM in secondary mode and running NI status possible value : notPresent <=> NI not present up <=> NI up and running down <=> NI down and powered unpowered <=> NI unpowered because there is not enough power in the system (chasEntPhysAdminStatus = powerOn) or because the NI has to be OFF (chasEntPhysAdminStatus = powerOff). This operational status has not full meaning without chasEntPhysAdminStatus Fabric status possible value : master <=> up and acting as master up <=> up and acting as slave secondary <=> secondary mode for redundancy Daughter board status possible value : notPresent <=> DB not present up <=> DB up and running down <=> DB down and powered Power supply status possible value : up <=> PS up down <=> PS administratively down unpowered <=> PS not plugged in pwrsave <=> chassis in powersave mode, supply turned off Fan Tray status possible value : up <=> powered up down <=> powered down fault <=> fault detectedro
Enumeration
.1.3.6.1.4.1.6486.801.1.1.1.1.1.1.1.2
chasEntPhysPowerThis value is only applicable to the NI, PS and Control Modules. It corresponds to a a static value for the power consumption of an NI module or Control Module. This value is in Watts.ro
Integer32
.1.3.6.1.4.1.6486.801.1.1.1.1.1.1.1.3
chasEntPhysModuleTypeThis object is the unique Module Type or ID from the entities eeprom. This value is guarrantteed to be unique to each type of Module. This value is only intended for Alcatel internal use.ro
SnmpAdminString (SNMP-FRAMEWORK-MIB)
.1.3.6.1.4.1.6486.801.1.1.1.1.1.1.1.4
chasEntPhysPartNumberThis object contains the Alcatel Part Number for the entity. This value is used to identify what is needed when placing orders with Alcatel.ro
SnmpAdminString
.1.3.6.1.4.1.6486.801.1.1.1.1.1.1.1.5
chasEntPhysLedStatusOk1Chassis Management Module (CMM) front panel LED OK1 status indicationro
ChasEntPhysLed
.1.3.6.1.4.1.6486.801.1.1.1.1.1.1.1.6
chasEntPhysLedStatusOk2Chassis Management Module (CMM) front panel LED OK2 status indicationro
ChasEntPhysLed
.1.3.6.1.4.1.6486.801.1.1.1.1.1.1.1.7
chasEntPhysLedStatusPrimaryCMMChassis Management Module (CMM) front panel LED Primary chassis indicationro
ChasEntPhysLed
.1.3.6.1.4.1.6486.801.1.1.1.1.1.1.1.8
chasEntPhysLedStatusSecondaryCMMChassis Management Module (CMM) front panel LED Secondary chassis indicationro
ChasEntPhysLed
.1.3.6.1.4.1.6486.801.1.1.1.1.1.1.1.9
chasEntPhysLedStatusTemperatureChassis Management Module (CMM) front panel LED temperature status indicationro
ChasEntPhysLed
.1.3.6.1.4.1.6486.801.1.1.1.1.1.1.1.10
chasEntPhysLedStatusFanFor Hawk stacks used as a fan group status LED. For eagle CMM's user instead: Fan 1 (top left), Fan 2 (top right), Fan 3 (rear)ro
ChasEntPhysLed
.1.3.6.1.4.1.6486.801.1.1.1.1.1.1.1.11
chasEntPhysLedStatusBackupPSChassis backup power supply status indicationro
ChasEntPhysLed
.1.3.6.1.4.1.6486.801.1.1.1.1.1.1.1.12
chasEntPhysLedStatusInternalPSChassis internal power supply status indicationro
ChasEntPhysLed
.1.3.6.1.4.1.6486.801.1.1.1.1.1.1.1.13
chasEntPhysLedStatusControlChassis control statusro
ChasEntPhysLed
.1.3.6.1.4.1.6486.801.1.1.1.1.1.1.1.14
chasEntPhysLedStatusFabricChassis Management Module (CMM) Fabric status indicationro
ChasEntPhysLed
.1.3.6.1.4.1.6486.801.1.1.1.1.1.1.1.15
chasEntPhysLedStatusPSChassis Power Supply Unit status indicationro
ChasEntPhysLed
.1.3.6.1.4.1.6486.801.1.1.1.1.1.1.1.16
chasEntPhysAsic1RevThis object contains the ASIC revision Number of the ni entityro
SnmpAdminString
.1.3.6.1.4.1.6486.801.1.1.1.1.1.1.1.17
chasEntPhysAsic2RevThis object contains the ASIC revision Number of the ni entityro
SnmpAdminString
.1.3.6.1.4.1.6486.801.1.1.1.1.1.1.1.18
chasEntPhysAsic3RevThis object contains the ASIC revision Number of the ni entityro
SnmpAdminString
.1.3.6.1.4.1.6486.801.1.1.1.1.1.1.1.19
chasEntPhysAsic4RevThis object contains the ASIC revision Number of the ni entityro
SnmpAdminString
.1.3.6.1.4.1.6486.801.1.1.1.1.1.1.1.20
chasEntPhysAsic5RevThis object contains the ASIC revision Number of the ni entityro
SnmpAdminString
.1.3.6.1.4.1.6486.801.1.1.1.1.1.1.1.21
chasEntPhysAsic6RevThis object contains the ASIC revision Number of the ni entityro
SnmpAdminString
.1.3.6.1.4.1.6486.801.1.1.1.1.1.1.1.22
chasEntPhysCpldRevThis object contains the CPLD revision Number of the ni entityro
SnmpAdminString
.1.3.6.1.4.1.6486.801.1.1.1.1.1.1.1.23
chasEntPhysDaughterFpga1RevThis object contains the daughter fpga revision Number of the ni entityro
SnmpAdminString
.1.3.6.1.4.1.6486.801.1.1.1.1.1.1.1.24
chasEntPhysDaughterFpga2RevThis object contains the daughter fpga revision Number of the ni entityro
SnmpAdminString
.1.3.6.1.4.1.6486.801.1.1.1.1.1.1.1.25
chasEntPhysNiNumThis value is only applicable to the NI. It indicates an NI associated with this physicalEntryro
Integer32
.1.3.6.1.4.1.6486.801.1.1.1.1.1.1.1.26
chasEntPhysGbicNumThis value is only applicable to the NI. It indicates a gbic associated with this niro
Integer32
.1.3.6.1.4.1.6486.801.1.1.1.1.1.1.1.27
chasEntPhysWaveLenThis object contains the wave length of a SFP devicero
Integer32
.1.3.6.1.4.1.6486.801.1.1.1.1.1.1.1.28
chasEntPhysUbootRevThis object contains the uboot version Number of the ni entityro
SnmpAdminString
.1.3.6.1.4.1.6486.801.1.1.1.1.1.1.1.29
chasEntPhysUbootMinibootRevThis object contains the uboot miniboot version Number of the ni entityro
SnmpAdminString
.1.3.6.1.4.1.6486.801.1.1.1.1.1.1.1.30
chasEntPhysMacAddressThis object contains the MAC address of the ni entityro
MacAddress (SNMPv2-TC)
.1.3.6.1.4.1.6486.801.1.1.1.1.1.1.1.31
chasEntPhysCpuModelThis object contains the model description of the cmm/ni cpuro
SnmpAdminString
.1.3.6.1.4.1.6486.801.1.1.1.1.1.1.1.32
chasEntPhysAirflowChassis PS fan airflow directionro
Enumeration
.1.3.6.1.4.1.6486.801.1.1.1.1.1.1.1.33
chasEntPhysPowerUsedThis value is only applicable to the PS. It is the current reading for the power usage of the PS. This value is in Watts.ro
Integer32
.1.3.6.1.4.1.6486.801.1.1.1.1.1.1.1.34
chasEntTemperatureTableThis table contains one row per temperature sensor located on an entity represented by the associated row in the entPhysicalTable.
SEQUENCE OF ChasEntTemperatureEntry
.1.3.6.1.4.1.6486.801.1.1.1.1.1.2
chasEntTemperatureEntryInformation about a particular physical temperature sensor.
ChasEntTemperatureEntry
.1.3.6.1.4.1.6486.801.1.1.1.1.1.2.1
chasEntTempCurrentThis object indicates the current output of the temperature sensor in degrees Celsius.ro
Integer32
.1.3.6.1.4.1.6486.801.1.1.1.1.1.2.1.1
chasEntTempThresholdThis object is the threshold temperature in degrees Celsius for the sensor. When the value of chasEntTempCurrent exceeds this value, a temperature notification is provided to the user.ro
Integer32
.1.3.6.1.4.1.6486.801.1.1.1.1.1.2.1.2
chasEntTempDangerThresholdThis object is the danger threshold temperature in degrees Celsius for the sensor. When the value of chasEntTempCurrent exceeds this value, the associated physical entity is powered down.ro
Integer32
.1.3.6.1.4.1.6486.801.1.1.1.1.1.2.1.3
chasEntTempStatusThis object is the status value of the temperature sensor. It reflects the temperature relative to the chasEntTempThreshold and chasEntTempDangerThreshold values.ro
Enumeration
.1.3.6.1.4.1.6486.801.1.1.1.1.1.2.1.4
alcatelIND1ChassisPhysMIBConformanceBranch For Chassis Supervision Chassis Physical MIB Subsystem Conformance Information.
OBJECT IDENTIFIER
.1.3.6.1.4.1.6486.801.1.1.1.1.2
alcatelIND1ChassisPhysMIBGroupsBranch For Chassis Supervision Chassis Physical MIB Subsystem Units Of Conformance.
OBJECT IDENTIFIER
.1.3.6.1.4.1.6486.801.1.1.1.1.2.1
alcatelIND1ChassisPhysMIBCompliancesBranch For Chassis Supervision Chassis Physical MIB Subsystem Compliance Statements.
OBJECT IDENTIFIER
.1.3.6.1.4.1.6486.801.1.1.1.1.2.2
alcatelIND1ChassisMIBThis module describes an authoritative enterprise-specific Simple etwork Management Protocol (SNMP) Management Information Base (MIB): For the Birds Of Prey Product Line, this is the Chassis Supervision Chassis MIB for managing physical chassis objects not covered in the IETF Entity MIB (rfc 2737). The right to make changes in specification and other information contained in this document without prior notice is reserved. No liability shall be assumed for any incidental, indirect, special, or consequential damages whatsoever arising from or related to this document or the information contained herein. Vendors, end-users, and other interested parties are granted non-exclusive license to use this specification in connection with management of the products for which it is intended to be used. Copyright (C) 1995-2007 Alcatel-Lucent ALL RIGHTS RESERVED WORLDWIDE
MODULE-IDENTITY
.1.3.6.1.4.1.6486.801.1.1.1.3.1
IMPORTSThis module describes an authoritative enterprise-specific Simple etwork Management Protocol (SNMP) Management Information Base (MIB): For the Birds Of Prey Product Line, this is the Chassis Supervision Chassis MIB for managing physical chassis objects not covered in the IETF Entity MIB (rfc 2737). The right to make changes in specification and other information contained in this document without prior notice is reserved. No liability shall be assumed for any incidental, indirect, special, or consequential damages whatsoever arising from or related to this document or the information contained herein. Vendors, end-users, and other interested parties are granted non-exclusive license to use this specification in connection with management of the products for which it is intended to be used. Copyright (C) 1995-2007 Alcatel-Lucent ALL RIGHTS RESERVED WORLDWIDE
Unknown
.1.3.6.1.4.1.6486.801.1.1.1.3.1
alcatelIND1ChassisMIBNotificationsBranch For Chassis MIB Subsystem Notifications.
OBJECT IDENTIFIER
.1.3.6.1.4.1.6486.801.1.1.1.3.1.0
chassisTrapsStrA Software Trouble report is sent by whatever application encountering a problem during its execution and would want to aware the user of for maintenance purpose.
NOTIFICATION-TYPE
.1.3.6.1.4.1.6486.801.1.1.1.3.1.0.1
chassisTrapsAlertgeneric trap notifying something changed in the chassis whatever it's a failure or not
NOTIFICATION-TYPE
.1.3.6.1.4.1.6486.801.1.1.1.3.1.0.2
chassisTrapsStateChangeA status change was detected
NOTIFICATION-TYPE
.1.3.6.1.4.1.6486.801.1.1.1.3.1.0.3
chasTrapsBPSLessAllocSysPwrInsufficient system power given by BPS
NOTIFICATION-TYPE
.1.3.6.1.4.1.6486.801.1.1.1.3.1.0.4
chasTrapsBPSStateChangeBPS power supplies insertion/removal trap
NOTIFICATION-TYPE
.1.3.6.1.4.1.6486.801.1.1.1.3.1.0.5
chasTrapsNiBPSFETStateChangeBPS power supplies FET state change trap
NOTIFICATION-TYPE
.1.3.6.1.4.1.6486.801.1.1.1.3.1.0.6
alcatelIND1ChassisMIBObjectsBranch For Chassis Supervision Chassis MIB Subsystem Managed Objects.
OBJECT IDENTIFIER
.1.3.6.1.4.1.6486.801.1.1.1.3.1.1
chasControlModuleTableThis table contains one row for the primary control module.
SEQUENCE OF ChasControlModuleEntry
.1.3.6.1.4.1.6486.801.1.1.1.3.1.1.1
chasControlModuleEntryInformation about the primary control module. This table is an extension of the entity physical table but this class is instanciated only for a the primary control module that has a particular Index. When operatiing in virtual chassis mode only the master primary control module is instanciated
ChasControlModuleEntry
.1.3.6.1.4.1.6486.801.1.1.1.3.1.1.1.1
chasControlActivateTimeoutThis value is in seconds. It represents how much time before the switch automatically falls back to the certified version. This value is set via the Activate(reload working) cli command. An Activate reboot must be initiated via the primary CMM and that the timeout value can be accessed via user interface to the primary CMM only. After the Activate reboot has been initiated, a timeout will occur (i.e., an Activate Timeout) at the timeout value specified by the user. If a reboot cancel has not been received prior to the timeout expiration, the primary CMM will automatically reboot (i.e., re-reboot) using the certified configuration. This ensures that an automatic backup reboot is available using the certified configuration in the event that the user is unable to interface with primary CMM as a result of the attempted Activate reboot. If the Activate reboot is successful, the user cancels the backup reboot via the normal reboot cancellation process (i.e., a zero value is written for the object chasControlDelayedRebootTimer).rw
Integer32
.1.3.6.1.4.1.6486.801.1.1.1.3.1.1.1.1.1
chasControlVersionMngtFor the primary this means: notSignificant - No command applied. certifySynchro - Copy the file from the working to the certified directory and from the primary to the secondary (reboot of the secondary). certifyNoSynchro - Copy the file from the working to the certified directory. flashSynchro - Copy the file from the primary to the secondary (reboot of the secondary). restore - Copy the file from the certified directory to the working directory. activate - Reload from the working directory. Activate can be scheduled. issu - In Service Software Upgrade (ISSU). shutdown - Shutdown chassis specified by chasControlChassisId. Halts and powers off NIs, halts primary and secondary CMMs. vcConvert - Copy the image files from the running directory to the working directory.rw
Enumeration
.1.3.6.1.4.1.6486.801.1.1.1.3.1.1.1.1.2
chasControlDelayedActivateTimerTimer value in seconds used to initiate a delayed activate of the primary CMM. Writing this object to a non-zero value results in CMM reboot of the working directory following expiration of the specified activate timer delay. Writing this object to zero results in an immediately activate process. It is now adjusted to wait a maximum of 366 days.rw
Unsigned32
.1.3.6.1.4.1.6486.801.1.1.1.3.1.1.1.1.3
chasControlCertifyStatusReturned value indicates if the control module has been certified (that is the working directory matches the certified directory)ro
Enumeration
.1.3.6.1.4.1.6486.801.1.1.1.3.1.1.1.1.4
chasControlSynchronizationStatusReturned value indicates if the control module has been synchronized (that is the working directory matches the working directory on the other control module(s) if present). Returned value is monoControlModule when no other control module is present.ro
Enumeration
.1.3.6.1.4.1.6486.801.1.1.1.3.1.1.1.1.5
chasControlAcrossCmmWorkingSynchroStatusReturned value indicates if the /working has been synchronized across the CMMs (that is the working directory matches the working directory on all CMMs if present)ro
Enumeration
.1.3.6.1.4.1.6486.801.1.1.1.3.1.1.1.1.6
chasControlAcrossCmmCertifiedSynchroStatusReturned value indicates if the /certified has been synchronized across the CMMs if present)ro
Enumeration
.1.3.6.1.4.1.6486.801.1.1.1.3.1.1.1.1.7
chasControlNextRunningVersionThe pathname for the image directory that will be used on the next reload. Value may be /flash/certified or /flash/<working directory name>.ro
SnmpAdminString (SNMP-FRAMEWORK-MIB)
.1.3.6.1.4.1.6486.801.1.1.1.3.1.1.1.1.8
chasControlCurrentRunningVersionThe pathname of the image directory to the version that is currently executing. Value may be /flash/certified or /flash/<working directory name>.rw
SnmpAdminString (SNMP-FRAMEWORK-MIB)
.1.3.6.1.4.1.6486.801.1.1.1.3.1.1.1.1.9
chasControlWorkingVersionThe path to the currently specified working image directory. Value may be /flash/certified or /flash/<working directory name>.rw
SnmpAdminString (SNMP-FRAMEWORK-MIB)
.1.3.6.1.4.1.6486.801.1.1.1.3.1.1.1.1.10
chasControlRedundancyTimeTime in minutes that the running image must stay up without error before a subsequent error reset will restart the board from the running image. If a CMM in dual-CMM switch fails after a reload and before chasControlRedundancyTime expires, both CMMs will be rebooted from the certified version.rw
Integer32
.1.3.6.1.4.1.6486.801.1.1.1.3.1.1.1.1.11
chasControlEmpIpAddressThis object is deprecated. Instead use alaInterfaceTable(ALCATEL-IND1-IP-MIB) when configuring EMP interfaces. The IP Address for the primary control module EMP interface. This address is used for managing the chassis and will continue as the EMP interface address after a takeover.rwdeprecated
IpAddress
.1.3.6.1.4.1.6486.801.1.1.1.3.1.1.1.1.12
chasControlEmpIpMaskThis object is deprecated. Instead use alaInterfaceTable(ALCATEL-IND1-IP-MIB) when configuring EMP interfaces. The IP Address Mask for the primary control module EMP interface. This address mask is used for managing the chassis and will continue as the EMP interface mask after a takeover.rwdeprecated
IpAddress
.1.3.6.1.4.1.6486.801.1.1.1.3.1.1.1.1.13
chasControlChassisIdThe virtual chassis id for the action specified by chasControlVersionMngt when operating in virtual chassis mode. A value of 0 indicates the local chassis.rw
Integer32
.1.3.6.1.4.1.6486.801.1.1.1.3.1.1.1.1.14
chasControlRedundantTableThis table contains one row per control module. There is always at least one control module in the system.
SEQUENCE OF ChasControlRedundantEntry
.1.3.6.1.4.1.6486.801.1.1.1.3.1.1.2
chasControlRedundantEntryInformation about a particular control module this table is an extension of the entity physical table but this class is instanciated only for a particular type of physical entity: the control module that has a particular Index. When running in virtual chassis mode, entries are instantiated for the Master and all the slave CMMs
ChasControlRedundantEntry
.1.3.6.1.4.1.6486.801.1.1.1.3.1.1.2.1
chasControlNumberOfTakeoverThis object is a count of the number of times the control module has changed from primary to secondary mode as a result of a Takeover. Note that this object can be accessed via user interface to either the primary or secondary CMM. The value returned is the number of times that the interfacing control module (either primary or secondary CMM) has changed from primary to secondary mode. This value does not reflect the total number of CMM Takeovers for the switch. To get the total number of Takeovers for the switch, it is necessary to read this value via user interface to each control module independently.ro
Counter32
.1.3.6.1.4.1.6486.801.1.1.1.3.1.1.2.1.1
chasControlDelayedRebootTimerTimer value (in seconds) used to initiate a delayed reboot of the primary or secondary CMM using the certified configuration. Writing this object to a non-zero value results in a CMM reboot following expiration of the specified reset timer delay. Writing this object to zero results in cancellation of a pending CMM delayed reboot. It is now adjusted to wait a maximum of 366 days.rw
Unsigned32 (0.. 31622400)
.1.3.6.1.4.1.6486.801.1.1.1.3.1.1.2.1.2
chasControlDelayedResetAllThis object is used to schedule a delayed reset all action for a chassis when running in virtual chassis mode. If set to -1 - cancel the timer, 0 - reset all immediately, any other value will start counting down the time until reset.rw
Integer32 (-1..65535)
.1.3.6.1.4.1.6486.801.1.1.1.3.1.1.2.1.3
chasChassisTableThis table contains one row per chassis. There is always at least one chassis or many when running in virtual chassis mode.
SEQUENCE OF ChasChassisEntry
.1.3.6.1.4.1.6486.801.1.1.1.3.1.1.3
chasChassisEntryInformation about a particular control module this table is an extension of the entity physical table but this class is instanciated only for a particular type of physical entity: the control module that has a particular Index.
ChasChassisEntry
.1.3.6.1.4.1.6486.801.1.1.1.3.1.1.3.1
chasFreeSlotsThe number of free NI front panel slots.ro
Unsigned32
.1.3.6.1.4.1.6486.801.1.1.1.3.1.1.3.1.1
chasPowerLeftThe power still available on the chassis in Watts.ro
Integer32 (-100000..100000)
.1.3.6.1.4.1.6486.801.1.1.1.3.1.1.3.1.2
chasNumberOfResetsThis object is a count of the number of times this station has been reset since a cold-start.ro
Counter32
.1.3.6.1.4.1.6486.801.1.1.1.3.1.1.3.1.3
chasTempRangeTemp Range is the value of the temperature sensor for the chassis. The Temp Range value reflects the temperature of the chassis relative to the Temp Threshold value (i.e., over vs. under the threshold).ro
Enumeration
.1.3.6.1.4.1.6486.801.1.1.1.3.1.1.3.1.4
chasTempThresholdThis object is the threshold temperature in degrees Celsius for the chassis. Temp Threshold is the chassis temperature point at which, when reached due to an ascending or descending temperature transition, a temperature notification is provided to the user. When this threshold is exceeded, we start sending traps and other operator notification.rw
Integer32
.1.3.6.1.4.1.6486.801.1.1.1.3.1.1.3.1.5
chasDangerTempThresholdThis Threshold is a second one which is hardcoded. When the Chassis Exceeds this value it starts shutting down NIs. This value will be set by the factory and not changeable.ro
Integer32
.1.3.6.1.4.1.6486.801.1.1.1.3.1.1.3.1.6
chasPrimaryPhysicalIndexThis value holds the Entity Table Physical Index for the Control Module that is currently primary. This is to allow snmp managers to determine which Control Module is currently primary so it knows what entry in the chasControlModuleTable to access for setting the chasControlVersionMngt values for controling the switch. When running in virtual chassis mode, it will contain the Physical Index of the master primary Control Module.ro
Integer32
.1.3.6.1.4.1.6486.801.1.1.1.3.1.1.3.1.7
chasCPMAHardwareBoardTempThis object indicates the current output of the Board Temperature Sensor provided by the LM75 part (degrees Centigrade) for the CPMA control module board. This temperature is what is used for comparing to the threshold and determining whether the value is in range.ro
Integer32
.1.3.6.1.4.1.6486.801.1.1.1.3.1.1.3.1.8
chasCFMAHardwareBoardTempThis object indicates the current output of the Board Temperature Sensor provided by the LM75 part (degrees Centigrade) for the CFMA fabric board. This temperature is what is used for comparing to the threshold and determining whether the value is in range.ro
Integer32
.1.3.6.1.4.1.6486.801.1.1.1.3.1.1.3.1.9
chasCPMBHardwareBoardTempThis object indicates the current output of the Board Temperature Sensor provided by the LM75 part (degrees Centigrade) for the CPMB control module board. This temperature is what is used for comparing to the threshold and determining whether the value is in range.ro
Integer32
.1.3.6.1.4.1.6486.801.1.1.1.3.1.1.3.1.10
chasCFMBHardwareBoardTempThis object indicates the current output of the Board Temperature Sensor provided by the LM75 part (degrees Centigrade) for the CFMB fabric board. This temperature is what is used for comparing to the threshold and determining whether the value is in range.ro
Integer32
.1.3.6.1.4.1.6486.801.1.1.1.3.1.1.3.1.11
chasCFMCHardwareBoardTempThis object indicates the current output of the Board Temperature Sensor provided by the LM75 part (degrees Centigrade) for the CFMC fabric board. This temperature is what is used for comparing to the threshold and determining whether the value is in range.ro
Integer32
.1.3.6.1.4.1.6486.801.1.1.1.3.1.1.3.1.12
chasCFMDHardwareBoardTempThis object indicates the current output of the Board Temperature Sensor provided by the LM75 part (degrees Centigrade) for the CFMD fabric board. This temperature is what is used for comparing to the threshold and determining whether the value is in range.ro
Integer32
.1.3.6.1.4.1.6486.801.1.1.1.3.1.1.3.1.13
chasFTAHardwareBoardTempThis object indicates the current output of the Board Temperature Sensor provided by the LM75 part (degrees Centigrade) for Fantray 1. This temperature is what is used for comparing to the threshold and determining whether the value is in range.ro
Integer32
.1.3.6.1.4.1.6486.801.1.1.1.3.1.1.3.1.14
chasFTBHardwareBoardTempThis object indicates the current output of the Board Temperature Sensor provided by the LM75 part (degrees Centigrade) for Fantry 2. This temperature is what is used for comparing to the threshold and determining whether the value is in range.ro
Integer32
.1.3.6.1.4.1.6486.801.1.1.1.3.1.1.3.1.15
chasNI1HardwareBoardTempThis object indicates the current output of the Board Temperature Sensor provided by the LM75 part (degrees Centigrade) for the NI board in slot 1. This temperature is what is used for comparing to the threshold and determining whether the value is in range.ro
Integer32
.1.3.6.1.4.1.6486.801.1.1.1.3.1.1.3.1.16
chasNI2HardwareBoardTempThis object indicates the current output of the Board Temperature Sensor provided by the LM75 part (degrees Centigrade) for the NI board in slot 2. This temperature is what is used for comparing to the threshold and determining whether the value is in range.ro
Integer32
.1.3.6.1.4.1.6486.801.1.1.1.3.1.1.3.1.17
chasNI3HardwareBoardTempThis object indicates the current output of the Board Temperature Sensor provided by the LM75 part (degrees Centigrade) for the NI board in slot 3. This temperature is what is used for comparing to the threshold and determining whether the value is in range.ro
Integer32
.1.3.6.1.4.1.6486.801.1.1.1.3.1.1.3.1.18
chasNI4HardwareBoardTempThis object indicates the current output of the Board Temperature Sensor provided by the LM75 part (degrees Centigrade) for the NI board in slot 4. This temperature is what is used for comparing to the threshold and determining whether the value is in range.ro
Integer32
.1.3.6.1.4.1.6486.801.1.1.1.3.1.1.3.1.19
chasNI5HardwareBoardTempThis object indicates the current output of the Board Temperature Sensor provided by the LM75 part (degrees Centigrade) for the NI board in slot 5. This temperature is what is used for comparing to the threshold and determining whether the value is in range.ro
Integer32
.1.3.6.1.4.1.6486.801.1.1.1.3.1.1.3.1.20
chasNI6HardwareBoardTempThis object indicates the current output of the Board Temperature Sensor provided by the LM75 part (degrees Centigrade) for the NI board in slot 6. This temperature is what is used for comparing to the threshold and determining whether the value is in range.ro
Integer32
.1.3.6.1.4.1.6486.801.1.1.1.3.1.1.3.1.21
chasNI7HardwareBoardTempThis object indicates the current output of the Board Temperature Sensor provided by the LM75 part (degrees Centigrade) for the NI board in slot 7. This temperature is what is used for comparing to the threshold and determining whether the value is in range.ro
Integer32
.1.3.6.1.4.1.6486.801.1.1.1.3.1.1.3.1.22
chasNI8HardwareBoardTempThis object indicates the current output of the Board Temperature Sensor provided by the LM75 part (degrees Centigrade) for the NI board in slot 8. This temperature is what is used for comparing to the threshold and determining whether the value is in range.ro
Integer32
.1.3.6.1.4.1.6486.801.1.1.1.3.1.1.3.1.23
chasPowerSupplyRedundancyThis object indicates the state of power supply redundancy mode. When on(1), N+1 mode redundancy is enabled(default mode). In this mode the system controls the power supplies to maintain efficient use of the power supplies, with 1 extra power supply in case of a power supply failure. Unneeded power supplies are powered off. It can be set to off(2) to disable redundancy mode. In this mode all power supplies are powered on.rw
Enumeration
.1.3.6.1.4.1.6486.801.1.1.1.3.1.1.3.1.24
chasSupervisionRfsLsTableThis table contains a list of file on the remote chassis per directory.
SEQUENCE OF ChasSupervisionRfsLsEntry
.1.3.6.1.4.1.6486.801.1.1.1.3.1.1.4
chasSupervisionRfsLsEntryInformation about a remote file. A row in this table contains a file per directory per chassis
ChasSupervisionRfsLsEntry
.1.3.6.1.4.1.6486.801.1.1.1.3.1.1.4.1
chasSupervisionRfsLsFileIndexThis value holds file Index for the RFS LS table.ro
Integer32
.1.3.6.1.4.1.6486.801.1.1.1.3.1.1.4.1.1
chasSupervisionRfsLsSlotCMM Slot where remote file is located.ro
Unsigned32
.1.3.6.1.4.1.6486.801.1.1.1.3.1.1.4.1.2
chasSupervisionRfsLsDirNameThe remote directory name where remote file is located inro
SnmpAdminString
.1.3.6.1.4.1.6486.801.1.1.1.3.1.1.4.1.3
chasSupervisionRfsLsFileNameThe file name of remote filero
SnmpAdminString
.1.3.6.1.4.1.6486.801.1.1.1.3.1.1.4.1.4
chasSupervisionRfsLsFileTypeThe Type of a remote filero
Enumeration
.1.3.6.1.4.1.6486.801.1.1.1.3.1.1.4.1.5
chasSupervisionRfsLsFileSizesize of this remote filero
Unsigned32
.1.3.6.1.4.1.6486.801.1.1.1.3.1.1.4.1.6
chasSupervisionRfsLsFileAttrattributes of this remote filero
Enumeration
.1.3.6.1.4.1.6486.801.1.1.1.3.1.1.4.1.7
chasSupervisionRfsLsFileDateTimethe modification date and time of a remote filero
SnmpAdminString
.1.3.6.1.4.1.6486.801.1.1.1.3.1.1.4.1.8
alcatelIND1ChassisSupervisionRfsCommandsBranch For Chassis Supervision RFS commands. For rrm command the Slot, Command and SrcFileName are mandatory. For rcp command the Slot, Command, SrcFileName and DestFileName are mandatory. For rdf command the Slot and Command are mandatory
OBJECT IDENTIFIER
.1.3.6.1.4.1.6486.801.1.1.1.3.1.1.5
chasSupervisionRfsCommandsSlotCMM Slot where RFS command should be executed.rw
Unsigned32
.1.3.6.1.4.1.6486.801.1.1.1.3.1.1.5.1
chasSupervisionRfsCommandsCommandThis object identifies which of the above Actions is to be performed. The commands are as follows: - rrm Remote file remove - rcp Remote file copy (DEPRECATED please use rget or rput instead) - rls Remote directory listing - rdf Remote flash disk space free - rget Remote file get - rput Remote file putrw
Enumeration
.1.3.6.1.4.1.6486.801.1.1.1.3.1.1.5.2
chasSupervisionRfsCommandsSrcFileNameThe remote file for where the RFS action is executed. This includes also the path so directory name and file name. This object is used when command set to rrm or rget or rput.rw
SnmpAdminString
.1.3.6.1.4.1.6486.801.1.1.1.3.1.1.5.3
chasSupervisionRfsCommandsDestFileNameThe destination file for where the RFS action is executed. This includes also the path so directory name and file name. This object is used when command set to rget or rput.rw
SnmpAdminString
.1.3.6.1.4.1.6486.801.1.1.1.3.1.1.5.4
chasSupervisionRfsCommandsRlsDirNameThe remote directory name where remote file is located in. This is used when command set to rls.rw
SnmpAdminString
.1.3.6.1.4.1.6486.801.1.1.1.3.1.1.5.5
chasSupervisionRfsCommandsRlsFileNameThe remote file name where remote file is located in. This is used when command set to rls.rw
SnmpAdminString
.1.3.6.1.4.1.6486.801.1.1.1.3.1.1.5.6
chasSupervisionRfsCommandsProcessingStatecommand executing state for the previous set operation.ro
Enumeration
.1.3.6.1.4.1.6486.801.1.1.1.3.1.1.5.7
chasSupervisionRfsCommandsStatusCodecommand completetion status error code.ro
Enumeration
.1.3.6.1.4.1.6486.801.1.1.1.3.1.1.5.8
chasControlReloadStatusTableTable containing reload status of each network interface slot or stack module
SEQUENCE OF ChasControlReloadEntry
.1.3.6.1.4.1.6486.801.1.1.1.3.1.1.6
chasControlReloadEntryEntry of a network interface reload status
ChasControlReloadEntry
.1.3.6.1.4.1.6486.801.1.1.1.3.1.1.6.1
chasControlReloadIndexThe index (entPhsycialIndex) value of the network interface.
Integer32
.1.3.6.1.4.1.6486.801.1.1.1.3.1.1.6.1.1
chasControlReloadStatusReturned value indicates if the network interface module is enabled or disabled for reload.ro
Enumeration
.1.3.6.1.4.1.6486.801.1.1.1.3.1.1.6.1.2
chasGlobalControl
OBJECT IDENTIFIER
.1.3.6.1.4.1.6486.801.1.1.1.3.1.1.7
chasGlobalControlDelayedResetAllThis object is used to schedule a delayed reset all action for a standalone chassis or for the entire virtual chassis when running is virtual chassis mode. To schedule a delayed reset on a specific chassis when running is virtual chassis mode, use the chasControlDelayedResetAll object for the desired chassis. If set to -1 - cancel the timer, 0 - reset all immediately, any other value will start counting down the time until reset.rw
Integer32 (-1..65535)
.1.3.6.1.4.1.6486.801.1.1.1.3.1.1.7.1
chasGlobalControlLongCommandThis object is used to indicate whether a long-term action is in progress, and if so, what the action is.ro
Enumeration
.1.3.6.1.4.1.6486.801.1.1.1.3.1.1.7.2
chasGlobalControlLongCommandStatusThis object indicates the final disposition of the most recent long-term action. When running in virtual chassis mode, the value confirmationRequired(5), indicates that the command identified in chasGlobalControlLongCommand may disrupt the virtual chassis. The command is suspended and requires that chasClobalControlConfirmOperation be set to true, after reviewing the details and accepting the consequences identified by chasGlobalControlConfirmMessage.ro
Enumeration
.1.3.6.1.4.1.6486.801.1.1.1.3.1.1.7.3
chasGlobalControlUpdateFirmwareThis object initiates a firmware update. The chasGlobalControlUpdateSlot and chasGlobalControlUpdateFilename objects must be set prior to setting this object to start the update. The progress of the update can be monitored by reading chasGlobalControlUpdateStatus.rw
Enumeration
.1.3.6.1.4.1.6486.801.1.1.1.3.1.1.7.4
chasGlobalControlUpdateSlotThis object identifies the slot to be updated. The Slot value is the entPhysicalIndex of the NI or CMM entry in the entPhyscialTable. A value of 0 may be specified to update all NIs or CMMs. The value of 0 is supported only for uboot updates.rw
Integer32
.1.3.6.1.4.1.6486.801.1.1.1.3.1.1.7.5
chasGlobalControlUpdateFilenameThis object identifies the filename containing the uboot firmware image.rw
SnmpAdminString
.1.3.6.1.4.1.6486.801.1.1.1.3.1.1.7.6
chasGlobalControlUpdateStatusThis object reports the status of the firmware update. The status for the the update identified by chasGlobalControlUpdateFirmware and chasGlobalControlUpdateSlot is returned. When ubootNiAll(4) ubootCmmAll(5) or fpgaCmmAll(10) update is executed, the status of individual NIs or CMMs may be monitored by changing the value of chasGlobalControlUpdateSlot to the desired NI or CMM slot value prior to reading the status. noUpdate(1) - No firmware update has been initiated. updateInProgress(2) - Update is in progress. updateSuccess(3) - The last firmware update was successful. updateFailed(4) - The last firmware update failed.ro
Enumeration
.1.3.6.1.4.1.6486.801.1.1.1.3.1.1.7.7
chasGlobalControlConfirmOperationWhen operating in virtual chassis mode, this object can be set to true(1) to confirm that the operation identified by chasGlobalControlLongCommand can proceed. Set to false(2) to cancel the operation. This should only be used when chasGlobalControlLongCommandStatus is set to confirmationRequired(5), and the value of chasGlobalControlConfirmMessage has been reviewed.rw
TruthValue (SNMPv2-TC)
.1.3.6.1.4.1.6486.801.1.1.1.3.1.1.7.8
chasGlobalControlConfirmMessageWhen operating in virtual chassis mode, this object may be read when chasGlobalControlLongCommandStatus is set to confirmationRequired(5). This will happen when an operation such a reload may disrupt the virtual chassis. This object contains information about the consequences of executing the command identified by chasGlobalControlLongCommand. The command has been suspended. To accept the consequences and proceed with the operation, set chasGlobalControlConfirmOperation to true.ro
DisplayString (SNMPv2-TC)
.1.3.6.1.4.1.6486.801.1.1.1.3.1.1.7.9
chasSupervisionRfsDfTableThis table contains information about file system size and use.
SEQUENCE OF ChasSupervisionRfsDfEntry
.1.3.6.1.4.1.6486.801.1.1.1.3.1.1.8
chasSupervisionRfsDfEntryThis entry contains information about file system size and use.
ChasSupervisionRfsDfEntry
.1.3.6.1.4.1.6486.801.1.1.1.3.1.1.8.1
chasSupervisionRfsDfSlotCMM Slot where flash space is evaluated.
Integer32
.1.3.6.1.4.1.6486.801.1.1.1.3.1.1.8.1.1
chasSupervisionRfsDfFlashFreeNumber bytes free on the file system.ro
Unsigned32
.1.3.6.1.4.1.6486.801.1.1.1.3.1.1.8.1.2
chasSupervisionRfsDfFlashSizeNumber of total bytes on the file system.ro
Unsigned32
.1.3.6.1.4.1.6486.801.1.1.1.3.1.1.8.1.3
chasSupervisionRfsDfUsbFreeThe amount of free space on the USB file system.ro
Unsigned32 UNITS "kb"
.1.3.6.1.4.1.6486.801.1.1.1.3.1.1.8.1.4
chasSupervisionRfsDfUsbSizeThe total amount of space on the USB file system.ro
Unsigned32 UNITS "kb"
.1.3.6.1.4.1.6486.801.1.1.1.3.1.1.8.1.5
chasSupervisionFlashMemTableThis table contains the systems flash memory information.
SEQUENCE OF ChasSupervisionFlashMemEntry
.1.3.6.1.4.1.6486.801.1.1.1.3.1.1.9
chasSupervisionFlashMemEntryThis contains one entry for the flash memory table.
ChasSupervisionFlashMemEntry
.1.3.6.1.4.1.6486.801.1.1.1.3.1.1.9.1
chasSupervisionSlotCMM Slot where flash space is evaluated.
Integer32
.1.3.6.1.4.1.6486.801.1.1.1.3.1.1.9.1.1
chasSupervisionFlashSizeFlash memory size.ro
Unsigned32
.1.3.6.1.4.1.6486.801.1.1.1.3.1.1.9.1.2
chasSupervisionFlashFreeNumber bytes free on file system.ro
Unsigned32
.1.3.6.1.4.1.6486.801.1.1.1.3.1.1.9.1.3
chasSupervisionFlashUsedA rounded up percentage of Flash Memory used.ro
Integer32
.1.3.6.1.4.1.6486.801.1.1.1.3.1.1.9.1.4
chasSupervisionCmmCertifiedTableThis table contains certification status
SEQUENCE OF ChasSupervisionCmmCertifiedEntry
.1.3.6.1.4.1.6486.801.1.1.1.3.1.1.10
chasSupervisionCmmCertifiedEntryInformation about control module certification status. This class is instanciated only when running in virtual chassis mode.
ChasSupervisionCmmCertifiedEntry
.1.3.6.1.4.1.6486.801.1.1.1.3.1.1.10.1
chasSupervisionCmmNumCMM Slot where /certified directory is evaluated.
Integer32
.1.3.6.1.4.1.6486.801.1.1.1.3.1.1.10.1.1
chasSupervisionCmmCertifiedStatusThe status of the CMM certified directory - certified or not.ro
Enumeration
.1.3.6.1.4.1.6486.801.1.1.1.3.1.1.10.1.2
alaChasEntPhysFanTableThis table contains one row per physical fan entity.
SEQUENCE OF AlaChasEntPhysFanEntry
.1.3.6.1.4.1.6486.801.1.1.1.3.1.1.11
alaChasEntPhysFanEntryInformation about a particular fan in a chassis physical entity.
AlaChasEntPhysFanEntry
.1.3.6.1.4.1.6486.801.1.1.1.3.1.1.11.1
alaChasEntPhysFanLocalIndexIndex to a chassis fan entity
Integer32
.1.3.6.1.4.1.6486.801.1.1.1.3.1.1.11.1.1
alaChasEntPhysFanStatusChassis fan operational statusro
Enumeration
.1.3.6.1.4.1.6486.801.1.1.1.3.1.1.11.1.2
alaChasEntPhysFanAirflowChassis fan airflow directionro
Enumeration
.1.3.6.1.4.1.6486.801.1.1.1.3.1.1.11.1.3
chassisTrapsObj
OBJECT IDENTIFIER
.1.3.6.1.4.1.6486.801.1.1.1.3.1.1.13
chassisTrapsStrLevelAn enumerated value which provides the urgency level of the STR.ro
ChassisTrapsStrLevel
.1.3.6.1.4.1.6486.801.1.1.1.3.1.1.13.1
chassisTrapsStrAppIDApplication Identification numberro
ChassisTrapsStrAppID
.1.3.6.1.4.1.6486.801.1.1.1.3.1.1.13.2
chassisTrapsStrSnapIDSubapplication Identification number. we can have multiple snapIDs per Subapplication (task) but only one is to be used to send STRs.ro
ChassisTrapsStrSnapID
.1.3.6.1.4.1.6486.801.1.1.1.3.1.1.13.3
chassisTrapsStrfileNameName of the source file where the fault was detected. This is given by the C ANSI macro __FILE__. The path shouldn't appear.ro
SnmpAdminString
.1.3.6.1.4.1.6486.801.1.1.1.3.1.1.13.4
chassisTrapsStrfileLineNbLine number in the source file where the fault was detected. This is given by the C ANSI macro __LINE__.ro
ChassisTrapsStrfileLineNb
.1.3.6.1.4.1.6486.801.1.1.1.3.1.1.13.5
chassisTrapsStrErrorNbFault identificator. The error number identify the kind the detected fault and allow a mapping of the data contained in chassisTrapsdataInfo.ro
ChassisTrapsStrErrorNb
.1.3.6.1.4.1.6486.801.1.1.1.3.1.1.13.6
chassisTrapsStrcommentscomment text explaning the fault.ro
SnmpAdminString
.1.3.6.1.4.1.6486.801.1.1.1.3.1.1.13.7
chassisTrapsStrdataInfoAdditional data provided to help to find out the origine of the fault. The contain and the significant portion are varying in accordance with chassisTrapsStrErrorNb. The lenght of this field is expressed in bytes.ro
ChassisTrapsStrdataInfo
.1.3.6.1.4.1.6486.801.1.1.1.3.1.1.13.8
chassisTrapsObjectTypeenumerated value which provide the object type involved in the alert trap.ro
ChassisTrapsObjectType
.1.3.6.1.4.1.6486.801.1.1.1.3.1.1.13.9
chassisTrapsObjectNumbernumber defining the order of the object in the set. EX: number of the considered fan or power supply. This intend to clarify as much as possible the location of the failure or alert. A instance of the appearance of the trap could be: failure on a module. Power supply 3.ro
ChassisTrapsObjectNumber
.1.3.6.1.4.1.6486.801.1.1.1.3.1.1.13.10
chassisTrapsAlertNumberthis number identify the alert among all the possible chassis alert causes.ro
ChassisTrapsAlertNumber
.1.3.6.1.4.1.6486.801.1.1.1.3.1.1.13.11
chassisTrapsAlertDescrdescription of the alert matching chassisTrapsAlertNumberro
SnmpAdminString
.1.3.6.1.4.1.6486.801.1.1.1.3.1.1.13.12
physicalIndexThe Physical index of the involved object.ro
PhysicalIndex (ENTITY-MIB)
.1.3.6.1.4.1.6486.801.1.1.1.3.1.1.13.13
chasTrapsNiRqstdBpsSysPowerRequested system power from os-bpsro
Integer32
.1.3.6.1.4.1.6486.801.1.1.1.3.1.1.13.14
chasTrapsNiGrantdBpsSysPowerGranted system power from os-bpsro
Integer32
.1.3.6.1.4.1.6486.801.1.1.1.3.1.1.13.15
chasTrapBPSShelfIdGranted system power from os-bpsro
Integer32
.1.3.6.1.4.1.6486.801.1.1.1.3.1.1.13.16
chasTrapsBPSPowerSupplyvalue which provide bps power supply involved in the State change trapro
ChasTrapsBPSPowerSupply
.1.3.6.1.4.1.6486.801.1.1.1.3.1.1.13.17
chasTrapsBPSEventAlertenumerated value identifying alertro
ChasTrapsBPSEventAlert
.1.3.6.1.4.1.6486.801.1.1.1.3.1.1.13.18
chasTrapsBPSSystemFETChangeenumerated value which indicate Fet statero
ChasTrapsBPSFetState
.1.3.6.1.4.1.6486.801.1.1.1.3.1.1.13.19
chasTrapsBPSPoeFETChangeenumerated value which indicate Fet statero
ChasTrapsBPSFetState
.1.3.6.1.4.1.6486.801.1.1.1.3.1.1.13.20
alaChasBpsObjects
OBJECT IDENTIFIER
.1.3.6.1.4.1.6486.801.1.1.1.3.1.1.14
alaChasBpsFwTableThis table contains one row per shelf bps firrmware
SEQUENCE OF AlaChasBpsFwEntry
.1.3.6.1.4.1.6486.801.1.1.1.3.1.1.14.1
alaChasBpsFwEntryInformation about a bps firrmare
AlaChasBpsFwEntry
.1.3.6.1.4.1.6486.801.1.1.1.3.1.1.14.1.1
alaChasBpsShelfIdBps shelf ID
AlaChasBpsShelfId
.1.3.6.1.4.1.6486.801.1.1.1.3.1.1.14.1.1.1
alaChasBpsUpdateFirmwareThis object is used to start BPS firmware update.rw
Enumeration
.1.3.6.1.4.1.6486.801.1.1.1.3.1.1.14.1.1.2
alaChasBpsCpldRevThis object contains the CPLD revision Number of the BPSro
SnmpAdminString
.1.3.6.1.4.1.6486.801.1.1.1.3.1.1.14.1.1.3
alaChasBpsMmcuRevThis object contains the MMCU revision Number of the BPSro
SnmpAdminString
.1.3.6.1.4.1.6486.801.1.1.1.3.1.1.14.1.1.4
alaChasBpsCmcuRevThis object contains the CMCU revision Number of the BPSro
SnmpAdminString
.1.3.6.1.4.1.6486.801.1.1.1.3.1.1.14.1.1.5
alaChasBpsConnectorPriorityTableThis table contains BPS connector priority for each slot
SEQUENCE OF AlaChasBpsConnectorPriorityEntry
.1.3.6.1.4.1.6486.801.1.1.1.3.1.1.14.2
alaChasBpsConnectorPriorityEntryInformation about bps connector priority for each slot
AlaChasBpsConnectorPriorityEntry
.1.3.6.1.4.1.6486.801.1.1.1.3.1.1.14.2.1
alaChasBpsChassisIdNumbers allocated for the stack NIs as follows: - 1..8: valid and assigned slot numbers corresponding to values from the entPhysicalTable
Integer32
.1.3.6.1.4.1.6486.801.1.1.1.3.1.1.14.2.1.1
alaChasBpsConnectorShelfIdBps shelf IDro
AlaChasBpsShelfId
.1.3.6.1.4.1.6486.801.1.1.1.3.1.1.14.2.1.2
alaChasBpsConnectorPriorityThis object specifies the bps connector priority.rw
Integer32
.1.3.6.1.4.1.6486.801.1.1.1.3.1.1.14.2.1.3
alaChasBpsConnectorNumThis object specifies the bps connector num.ro
SnmpAdminString
.1.3.6.1.4.1.6486.801.1.1.1.3.1.1.14.2.1.4
alaChasBpsSerialNumThis object specifies the bps serial num.ro
SnmpAdminString
.1.3.6.1.4.1.6486.801.1.1.1.3.1.1.14.2.1.5
alaChasBpsModeTableThis table contains one row for bps config parameters.
SEQUENCE OF AlaChasBpsModeEntry
.1.3.6.1.4.1.6486.801.1.1.1.3.1.1.14.3
alaChasBpsModeEntryInformation about bps mode
AlaChasBpsModeEntry
.1.3.6.1.4.1.6486.801.1.1.1.3.1.1.14.3.1
alaChasBpsModeThis object is only applicable to BPS .Value is used to specify current Mode of switch.rw
Enumeration
.1.3.6.1.4.1.6486.801.1.1.1.3.1.1.14.3.1.1
alaChasBpsPowerSupplyTableThis table contains BPS power supplies details
SEQUENCE OF AlaChasBpsPowerSupplyEntry
.1.3.6.1.4.1.6486.801.1.1.1.3.1.1.14.4
alaChasBpsPowerSupplyEntryInformation about a particular BPS power supply
AlaChasBpsPowerSupplyEntry
.1.3.6.1.4.1.6486.801.1.1.1.3.1.1.14.4.1
alaChasBpsPowerSupplyShelfIdBPS shelf ID
AlaChasBpsShelfId
.1.3.6.1.4.1.6486.801.1.1.1.3.1.1.14.4.1.1
alaChasBpsPowerSupplyIndexThis value hold BPS power power supply Index
Integer32
.1.3.6.1.4.1.6486.801.1.1.1.3.1.1.14.4.1.2
alaChasBpsPowerSupplyNameThis object hold name of BPS power supplyro
SnmpAdminString
.1.3.6.1.4.1.6486.801.1.1.1.3.1.1.14.4.1.3
alaChasBpsPowerSupplyDescrThis object hold description of BPS power supplyro
SnmpAdminString
.1.3.6.1.4.1.6486.801.1.1.1.3.1.1.14.4.1.4
alaChasBpsPowerSupplyModuleTypeThis object is unique module Type or ID from BPS entities eepromro
SnmpAdminString
.1.3.6.1.4.1.6486.801.1.1.1.3.1.1.14.4.1.5
alaChasBpsPowerSupplyPartNumberThis object contains the BPS power supply Part Numberro
SnmpAdminString
.1.3.6.1.4.1.6486.801.1.1.1.3.1.1.14.4.1.6
alaChasBpsPowerSupplyHardwareRevThe vendor-specific hardware revision string for the BPS power supplies Note that if revision information is stored internally in a non-printable (e.g., binary) format, then the agent must convert such information to a printable format, in an implementation-specific manner. If no specific hardware revision string is associated with the physical component, or this information is unknown to the agent, then this object will contain a zero-length string.ro
SnmpAdminString
.1.3.6.1.4.1.6486.801.1.1.1.3.1.1.14.4.1.7
alaChasBpsPowerSupplySerialNumThe vendor-specific serial number string for the BPS power suppliesrw
SnmpAdminString
.1.3.6.1.4.1.6486.801.1.1.1.3.1.1.14.4.1.8
alaChasBpsPowerSupplyMfgDateThis object contains the manufacturing date of the BPS power supplies . Its format is mmm dd yyyy : NOV 27 2012.ro
SnmpAdminString
.1.3.6.1.4.1.6486.801.1.1.1.3.1.1.14.4.1.9
alaChasBpsPowerSupplyOperStatusOper status of BPS power supplyro
Enumeration
.1.3.6.1.4.1.6486.801.1.1.1.3.1.1.14.4.1.10
alaChasBpsPowerSupplyPowerProvIt corresponds to max power of BPS power supply. This value is in Watts.ro
Integer32
.1.3.6.1.4.1.6486.801.1.1.1.3.1.1.14.4.1.11
alaChasBpsTotalPowerAllocTableThis table contains one row for parameters which reflect total allocation by BPS .
SEQUENCE OF AlaChasBpsTotalPowerAllocEntry
.1.3.6.1.4.1.6486.801.1.1.1.3.1.1.14.5
alaChasBpsTotalPowerAllocEntryInformation about various bps config parameters
AlaChasBpsTotalPowerAllocEntry
.1.3.6.1.4.1.6486.801.1.1.1.3.1.1.14.5.1
alaChasBpsSysTotalAvailablePowerThis value is only applicable to the BPS Module. It corresponds to system total power available on BPS This value is in Watts.ro
Integer32
.1.3.6.1.4.1.6486.801.1.1.1.3.1.1.14.5.1.1
alaChasBpsSysTotalAllocationThis value is only applicable to the BPS Modules. It corresponds to total system power allocated by BPS This value is in Watts.ro
Integer32
.1.3.6.1.4.1.6486.801.1.1.1.3.1.1.14.5.1.2
alaChasBpsPoeTotalAvailablePowerThis value is only applicable to the BPS Modules. It corresponds to system total power available on BPS This value is in Watts.ro
Integer32
.1.3.6.1.4.1.6486.801.1.1.1.3.1.1.14.5.1.3
alaChasBpsPoeTotalAllocationThis value is only applicable to the Bps Modules. It corresponds to total POE power allocated by BPS This value is in Watts.ro
Integer32
.1.3.6.1.4.1.6486.801.1.1.1.3.1.1.14.5.1.4
alcatelIND1ChassisMIBConformanceBranch For Chassis Supervision Chassis MIB Subsystem Conformance Information.
OBJECT IDENTIFIER
.1.3.6.1.4.1.6486.801.1.1.1.3.1.2
alcatelIND1ChassisMIBGroupsBranch For Chassis Supervision Chassis MIB Subsystem Units Of Conformance.
OBJECT IDENTIFIER
.1.3.6.1.4.1.6486.801.1.1.1.3.1.2.1
alcatelIND1ChassisMIBCompliancesBranch For Chassis Supervision Chassis MIB Subsystem Compliance Statements.
OBJECT IDENTIFIER
.1.3.6.1.4.1.6486.801.1.1.1.3.1.2.2
ALCATEL-IND1-CHASSIS-MIB - SNMP MIB Reference | MIBs Explorer