ACC-RIP
AI MIB Summary
Standard SNMP MIB module defining data structures for ACC-RIP.
97
Objects
Active
Status
6
Dependencies
Imported Objects
Objects
97 total| Object Name |
|---|
accRip OBJECT IDENTIFIER .1.3.6.1.4.1.5.1.1.16 |
IMPORTS Unknown .1.3.6.1.4.1.5.1.1.16 |
accRipAdminStatusAdminstrative status of RIP protocol.
Extended causes subnet mask information to be included in
RIP packets, permitting variable-length subnet masking.rw Enumeration .1.3.6.1.4.1.5.1.1.16.1 |
accRipUpdateTimerThis unit will send updates to its neighbors at the interval
established by this timer. Note that all other RIP timers
are scaled off this value.rwobsolete TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.5.1.1.16.2 |
accRipGatewayDeclares if the unit is the gateway unit for an AS.
Indicates if the unit does or does not advertise that
it is the default route.
Extended mode causes EGP-derived information to be
included in RIP packets.rwobsolete Enumeration .1.3.6.1.4.1.5.1.1.16.3 |
accRipNeighborList OBJECT IDENTIFIER .1.3.6.1.4.1.5.1.1.16.5 |
accRipNeighborA neighbor to whom routing updates are sent,
and from whom updates are accepted.
RIP neighbors must be on the local network.
In the case of an unnumbered link this object
indicates the ifIndex of the link the neighbor
is connected to.rwobsolete IpAddress .1.3.6.1.4.1.5.1.1.16.5.1 |
accRipNeighborIfindexThe ifIndex of the port this RIP neighbor is conected
to. It is derived from the IP network table
(accIpAddrTable).roobsolete INTEGER .1.3.6.1.4.1.5.1.1.16.5.2 |
accRipInCmdCntsNumber of RIP command packets successfully received.roobsolete Counter .1.3.6.1.4.1.5.1.1.16.6 |
accRipInRspCntsNumber of RIP response packets successfully received.roobsolete Counter .1.3.6.1.4.1.5.1.1.16.7 |
accRipInErrorsNumber of RIP response and command packets received with
errors. Also includes count of packets that could
not be handled due to internal errors.roobsolete Counter .1.3.6.1.4.1.5.1.1.16.8 |
accRipOutCmdCntsNumber of RIP command packets successfully transmitted.roobsolete Counter .1.3.6.1.4.1.5.1.1.16.9 |
accRipOutRspCountsNumber of RIP response packets successfully transmitted.roobsolete Counter .1.3.6.1.4.1.5.1.1.16.10 |
accRipGeneral OBJECT IDENTIFIER .1.3.6.1.4.1.5.1.1.16.11 |
accRipMessageLevelThe configured diagnostic level for RIP. Setting this value
to 1 enables RIP to generate important diagnostic information.
Increasing the value increases the diagnostic information.
Level 7 is mostly informational.rw INTEGER .1.3.6.1.4.1.5.1.1.16.11.1 |
accRipDefaultVersionThe default verison of RIP to use on new RIP interfaces.rw Enumeration .1.3.6.1.4.1.5.1.1.16.11.2 |
accRip2IfConfExtTableAn extension of the rip2IfConfTable. SEQUENCE OF AccRip2IfConfExtEntry .1.3.6.1.4.1.5.1.1.16.12 |
accRip2IfConfExtEntryEach entry in this table contains proprietary extensions to the
rip2IfConfTable AccRip2IfConfExtEntry .1.3.6.1.4.1.5.1.1.16.12.1 |
accRip2IfConfExtAddressSame definition as rip2IfConfAddress.ro IpAddress .1.3.6.1.4.1.5.1.1.16.12.1.1 |
accRip2IfConfExtProfileAn index into the accRipProfileTablerw INTEGER .1.3.6.1.4.1.5.1.1.16.12.1.2 |
accRip2IfConfExtDefaultOnlyGenerate a default route only on this interface.rw Enumeration .1.3.6.1.4.1.5.1.1.16.12.1.3 |
accRip2IfConfExtDefaultMetricIf generating a default route this is the metric that will
be used in updates sent out this interface.rw INTEGER .1.3.6.1.4.1.5.1.1.16.12.1.4 |
accRip2IfConfExtMessageLevelThe configured diagnostic level for this RIP interface. Setting this
value to 1 will enable the interface to generate critical diagnostic
information. Increasing the value increases the diagnostic information.
Level 7 is mostly informational.rw INTEGER .1.3.6.1.4.1.5.1.1.16.12.1.5 |
accRip2IfConfExtAdminStatThe administrative state of this RIP interface.rw Enumeration .1.3.6.1.4.1.5.1.1.16.12.1.6 |
accRip2IfConfExtTxOnlySend RIP updates and ignore received updates on this interface.rw Enumeration .1.3.6.1.4.1.5.1.1.16.12.1.7 |
accRipProfileTableA table describing each of the RIP Profile groups. SEQUENCE OF AccRipProfileEntry .1.3.6.1.4.1.5.1.1.16.13 |
accRipProfileEntryEach entry in this table describes a Rip Profile Entry. AccRipProfileEntry .1.3.6.1.4.1.5.1.1.16.13.1 |
accRipProfileIdThe index into the accRipTimerGroupTablero INTEGER .1.3.6.1.4.1.5.1.1.16.13.1.1 |
accRipProfileUpdateIntervalThe periodic RIP update interval.rw INTEGER .1.3.6.1.4.1.5.1.1.16.13.1.2 |
accRipProfilePacketGapThe inter-packet gap between fragmented updates in
1/100's of a second.rw INTEGER .1.3.6.1.4.1.5.1.1.16.13.1.3 |
accRipProfileMaxPktsThe maximum number of packets that can be issued during
any update burst.rw INTEGER .1.3.6.1.4.1.5.1.1.16.13.1.4 |
accRipProfileRetxTOThe interval in seconds that RIP will wait before retransmitting
a triggered update (fragment).rw INTEGER .1.3.6.1.4.1.5.1.1.16.13.1.5 |
accRipProfileShortPollRetriesThe number of times RIP will retry to establish a non-responding
neighbor using the short poll interval (5 minutes) after the
neighbor has gone non-responding.rw INTEGER .1.3.6.1.4.1.5.1.1.16.13.1.6 |
accRipProfileBackgroundThe background poll interval that RIP will attempt to re-establish
a neighbor relationship.rw INTEGER .1.3.6.1.4.1.5.1.1.16.13.1.7 |
accRipProfileStatusThe current status of this protocol entry.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.5.1.1.16.13.1.8 |
accRipNbrTableA table describing RIP neighbor relationships. SEQUENCE OF AccRipNbrEntry .1.3.6.1.4.1.5.1.1.16.16 |
accRipNbrEntryEach entry in this table describes a administratively
configured RIP neighbor. Only the neighbors listed on
a interface are listened to. AccRipNbrEntry .1.3.6.1.4.1.5.1.1.16.16.1 |
accRipNbrIpAddrThe IP address of this system on the indicated subnet.ro IpAddress .1.3.6.1.4.1.5.1.1.16.16.1.1 |
accRipNbrTriggeredIndicates the RIP neighbor is using triggered (on demand) RIP.rw Enumeration .1.3.6.1.4.1.5.1.1.16.16.1.2 |
accRipNbrTypeThe ifIndex for the associated IP Interface. A non-zero valueindicates
that the interface is an unnumbered interface and ripNbrIfIpAddr has
the value of 0.0.0.0.rw INTEGER .1.3.6.1.4.1.5.1.1.16.16.1.3 |
accRipNbrStatusThe current status of this protocol entry.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.5.1.1.16.16.1.4 |
accDemandRipTableThis table contains information about demand RIP neighbors that
have been either administratively configured or dynamically
learnt. SEQUENCE OF AccDemandRipEntry .1.3.6.1.4.1.5.1.1.16.17 |
accDemandRipEntryEach entry of this table represents a single demand RIP neighbor. AccDemandRipEntry .1.3.6.1.4.1.5.1.1.16.17.1 |
accDemandRipNeighborThe RIP neighbors IP address. If this is an unnumbered link
then this object will represent the ifIndex of the interface.ro IpAddress .1.3.6.1.4.1.5.1.1.16.17.1.1 |
accDemandRipRetxTimeoutsThe number of times a retransmit timeout has occurred on
a demand RIP interface.ro Gauge .1.3.6.1.4.1.5.1.1.16.17.1.2 |
accDemandRipShortPollRetriesThe number of short poll retries to this neighbor.ro Gauge .1.3.6.1.4.1.5.1.1.16.17.1.3 |
accDemandRipBackGroundRetriesThe number of background poll retries to this neighbor.ro Gauge .1.3.6.1.4.1.5.1.1.16.17.1.4 |
accDemandRipTransitionsThe number of times this neighbor has transitioned from
the Down state to an Up state.ro Counter .1.3.6.1.4.1.5.1.1.16.17.1.5 |
accDemandRipSeqNumberThe sequence number of the last received update.ro INTEGER .1.3.6.1.4.1.5.1.1.16.17.1.6 |
accDemandRipStatusThe current status of the demand RIP neighbor.ro Enumeration .1.3.6.1.4.1.5.1.1.16.17.1.7 |
accRipExportTableA table describing RIP export policies. SEQUENCE OF AccRipExportEntry .1.3.6.1.4.1.5.1.1.16.18 |
accRipExportEntryEach entry in this table describes a administratively
configured export policy. AccRipExportEntry .1.3.6.1.4.1.5.1.1.16.18.1 |
accRipExportProtocolThe routing protocol by which the route was learned.ro Enumeration .1.3.6.1.4.1.5.1.1.16.18.1.1 |
accRipExportProtoSpecificProtocol dependant. Not currently used. Should always have an
instance value of zero.ro INTEGER .1.3.6.1.4.1.5.1.1.16.18.1.2 |
accRipExportNetworkThe prefix to be used when matching policies. Routes are
logically anded with the policies mask and compared to this
prefix.ro IpAddress .1.3.6.1.4.1.5.1.1.16.18.1.3 |
accRipExportMaskThe mask to be used when matching policies.ro IpAddress .1.3.6.1.4.1.5.1.1.16.18.1.4 |
accRipExportDestIfThe outbound interface for the update being created.ro IpAddress .1.3.6.1.4.1.5.1.1.16.18.1.5 |
accRipExportActionDetermines the policy taken on routes matching this
set of criteria.rw Enumeration .1.3.6.1.4.1.5.1.1.16.18.1.6 |
accRipExportMetricThe metric that is to be used when exporting a route
into the routing domain on the outgoing interface. The
value 16 tells RIP to use the protocol owners metric.
Reading the value 17 means that this object is not used.rw INTEGER .1.3.6.1.4.1.5.1.1.16.18.1.7 |
accRipExportStatusThe current status of this protocol entry.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.5.1.1.16.18.1.8 |
accRipImportTableA table describing RIP import policies. SEQUENCE OF AccRipImportEntry .1.3.6.1.4.1.5.1.1.16.19 |
accRipImportEntryEach entry in this table describes a administratively
configured import policy. AccRipImportEntry .1.3.6.1.4.1.5.1.1.16.19.1 |
accRipImportInterfaceThe interface from which the RIP update was received.ro IpAddress .1.3.6.1.4.1.5.1.1.16.19.1.1 |
accRipImportPeerAddressThe RIP neighbors address.ro IpAddress .1.3.6.1.4.1.5.1.1.16.19.1.2 |
accRipImportNetworkThe prefix to be used when matching policies. Routes are
logically anded with the policies mask and compared to this
prefix.ro IpAddress .1.3.6.1.4.1.5.1.1.16.19.1.3 |
accRipImportMaskThe mask to be used when matching policies.ro IpAddress .1.3.6.1.4.1.5.1.1.16.19.1.4 |
accRipImportActionThe action to take when a policy match occurs.rw Enumeration .1.3.6.1.4.1.5.1.1.16.19.1.5 |
accRipImportMetricThe metric that is to be used when importing a route
that has matched this policy. The value 16 tells RIP to
use the protocol owners metric.rw INTEGER .1.3.6.1.4.1.5.1.1.16.19.1.6 |
accRipImportPrefThe preference that RIP will assign to a
route matching this policy. The preference
is used to determine precedence between
other routing protocols that learn paths
to the same destination.rw INTEGER .1.3.6.1.4.1.5.1.1.16.19.1.7 |
accRipImportStatusThe current status of this protocol entry.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.5.1.1.16.19.1.8 |
accRipTraps OBJECT IDENTIFIER .1.3.6.1.4.1.5.1.1.16.20 |
accRipFiltPolAllocTrapIs due the memory shortage. This may mean that maximum
number of filter policies were already allocated.
SEVERITY-DEFAULT: Warning
EVENTTYPE-DEFAULT: 10
ADDITIONAL-TEXT-VARIABLES: { accTrapLogSeqNum,accRipTrapMsg }
PCAUSE-DEFAULT: 32 TRAP-TYPE .1.3.6.1.4.1.5.1.1.16.20.0.1 |
accRipFiltPolTrapIt happens when the user tries to delete a filter
policy that doesnt exist.
SEVERITY-DEFAULT: Warning
EVENTTYPE-DEFAULT: 10
ADDITIONAL-TEXT-VARIABLES: { accTrapLogSeqNum,accRipTrapMsg }
PCAUSE-DEFAULT: 7 TRAP-TYPE .1.3.6.1.4.1.5.1.1.16.20.0.2 |
accRipImpPolAllocTrapIs due the memory shortage. This may mean that maximum
number of Import policies were already allocated.
SEVERITY-DEFAULT: Warning
EVENTTYPE-DEFAULT: 10
ADDITIONAL-TEXT-VARIABLES: { accTrapLogSeqNum,accRipTrapMsg }
PCAUSE-DEFAULT: 32 TRAP-TYPE .1.3.6.1.4.1.5.1.1.16.20.0.3 |
accRipImpPolTrapIt happens when the user tries to delete an Import
policy that doesnt exist.
SEVERITY-DEFAULT: Warning
EVENTTYPE-DEFAULT: 10
ADDITIONAL-TEXT-VARIABLES: { accTrapLogSeqNum,accRipTrapMsg }
PCAUSE-DEFAULT: 7 TRAP-TYPE .1.3.6.1.4.1.5.1.1.16.20.0.4 |
accRipNbrTrapThe rip neighbor address entered by the user is
unreachable.
SEVERITY-DEFAULT: Warning
EVENTTYPE-DEFAULT: 10
ADDITIONAL-TEXT-VARIABLES: { accTrapLogSeqNum,accRipTrapMsg }
PCAUSE-DEFAULT: 7 TRAP-TYPE .1.3.6.1.4.1.5.1.1.16.20.0.5 |
accRipNbrIncompatTrapThis is due the fact that either Unumbered Ip
Neighbor is on a Numbered Link or vice versa.
SEVERITY-DEFAULT: Warning
EVENTTYPE-DEFAULT: 10
ADDITIONAL-TEXT-VARIABLES: { accTrapLogSeqNum,accRipTrapMsg }
PCAUSE-DEFAULT: 7 TRAP-TYPE .1.3.6.1.4.1.5.1.1.16.20.0.6 |
accRipDefProfTrapUser tried to delete default profile. Default profile
entry cant be deleted.
SEVERITY-DEFAULT: Warning
EVENTTYPE-DEFAULT: 10
ADDITIONAL-TEXT-VARIABLES: { accTrapLogSeqNum,accRipTrapMsg }
PCAUSE-DEFAULT: 7 TRAP-TYPE .1.3.6.1.4.1.5.1.1.16.20.0.7 |
accRipProfUsedByIntfTrapUser can delete only if the profile is not being used.
SEVERITY-DEFAULT: Warning
EVENTTYPE-DEFAULT: 10
ADDITIONAL-TEXT-VARIABLES: { accTrapLogSeqNum,accRipTrapMsg }
PCAUSE-DEFAULT: 7 TRAP-TYPE .1.3.6.1.4.1.5.1.1.16.20.0.8 |
accRipMustBeDisbldTrapCan change profiles only if RIP disabled.
SEVERITY-DEFAULT: Warning
EVENTTYPE-DEFAULT: 10
ADDITIONAL-TEXT-VARIABLES: { accTrapLogSeqNum,accRipTrapMsg }
PCAUSE-DEFAULT: 7 TRAP-TYPE .1.3.6.1.4.1.5.1.1.16.20.0.9 |
accRipUpdateIntTrapOccurs when the number of routes that RIP must send
in the updates out an interface causes the ppu value
and inter-packet gap to exceed the RIP update interval
of the iterface. To rectify this, either shorten the
inter-packet interval or increase the number of
packets-per-update. Another solution is to reduce the
number of routes sent out the interface by implementing
policy or aggregation.
SEVERITY-DEFAULT: Major
EVENTTYPE-DEFAULT: 10
ADDITIONAL-TEXT-VARIABLES: { accTrapLogSeqNum,accRipTrapMsg }
PCAUSE-DEFAULT: 8 TRAP-TYPE .1.3.6.1.4.1.5.1.1.16.20.0.10 |
accRipInitNbrTrapFailed initializing the neighbor due to the memory
shortage encoutered in allocating memory for either
the trigger timer for the group or for the structure
to hold Neighbors triggered RIP related information.
SEVERITY-DEFAULT: Major
EVENTTYPE-DEFAULT: 10
ADDITIONAL-TEXT-VARIABLES: { accTrapLogSeqNum,accRipTrapMsg }
PCAUSE-DEFAULT: 32 TRAP-TYPE .1.3.6.1.4.1.5.1.1.16.20.0.11 |
accRipNbrAvlInsrtTrapIs due the memory shortage. This trap is while creating
a neighbor strucutre for the RIP interface.
SEVERITY-DEFAULT: Major
EVENTTYPE-DEFAULT: 10
ADDITIONAL-TEXT-VARIABLES: { accTrapLogSeqNum,accRipTrapMsg }
PCAUSE-DEFAULT: 32 TRAP-TYPE .1.3.6.1.4.1.5.1.1.16.20.0.12 |
accRipRtNotifIdTrapThis is a NBMA interface and it is up. Trap occured
while acquiring cl_id for this neighbor.
SEVERITY-DEFAULT: Warning
EVENTTYPE-DEFAULT: 10
ADDITIONAL-TEXT-VARIABLES: { accTrapLogSeqNum,accRipTrapMsg }
PCAUSE-DEFAULT: 0 TRAP-TYPE .1.3.6.1.4.1.5.1.1.16.20.0.13 |
accRipNbrNxtHopMemTrapSEVERITY-DEFAULT: Major
EVENTTYPE-DEFAULT: 10
ADDITIONAL-TEXT-VARIABLES: { accTrapLogSeqNum,accRipTrapMsg }
PCAUSE-DEFAULT: 32 TRAP-TYPE .1.3.6.1.4.1.5.1.1.16.20.0.14 |
accRipNoIntfMemTrapNo memory for RIP interface.
SEVERITY-DEFAULT: Major
EVENTTYPE-DEFAULT: 10
ADDITIONAL-TEXT-VARIABLES: { accTrapLogSeqNum,accRipTrapMsg }
PCAUSE-DEFAULT: 32 TRAP-TYPE .1.3.6.1.4.1.5.1.1.16.20.0.15 |
accRipAddNbrRtTrapAdd nbr route faild due to the memory shortage.
SEVERITY-DEFAULT: Major
EVENTTYPE-DEFAULT: 10
ADDITIONAL-TEXT-VARIABLES: { accTrapLogSeqNum,accRipTrapMsg }
PCAUSE-DEFAULT: 32 TRAP-TYPE .1.3.6.1.4.1.5.1.1.16.20.0.16 |
accRipMaxIntfGrpTrapThe number of different interface groups is limited
to the constant by RIP_MAX_INTF_GROUPS.
SEVERITY-DEFAULT: Warning
EVENTTYPE-DEFAULT: 10
ADDITIONAL-TEXT-VARIABLES: { accTrapLogSeqNum,accRipTrapMsg }
PCAUSE-DEFAULT: 7 TRAP-TYPE .1.3.6.1.4.1.5.1.1.16.20.0.17 |
accRipMemReqTrapMemory request failure.
SEVERITY-DEFAULT: Major
EVENTTYPE-DEFAULT: 10
ADDITIONAL-TEXT-VARIABLES: { accTrapLogSeqNum,accRipTrapMsg }
PCAUSE-DEFAULT: 32 TRAP-TYPE .1.3.6.1.4.1.5.1.1.16.20.0.18 |
accRipUpdateEvntHndlrTrapIs due the memory shortage. It is while creating
update timer.
SEVERITY-DEFAULT: Major
EVENTTYPE-DEFAULT: 10
ADDITIONAL-TEXT-VARIABLES: { accTrapLogSeqNum,accRipTrapMsg }
PCAUSE-DEFAULT: 32 TRAP-TYPE .1.3.6.1.4.1.5.1.1.16.20.0.19 |
accRipIntfLnkUpTrapIs due the memory shortage. It is while creating
update timer.
SEVERITY-DEFAULT: Major
EVENTTYPE-DEFAULT: 10
ADDITIONAL-TEXT-VARIABLES: { accTrapLogSeqNum,accRipTrapMsg }
PCAUSE-DEFAULT: 32 TRAP-TYPE .1.3.6.1.4.1.5.1.1.16.20.0.20 |
accRipEnableTrapThis is when enabling the RIP interface is failed
which is due to either Insufficient info or rip
interface group not bound.
SEVERITY-DEFAULT: Major
EVENTTYPE-DEFAULT: 10
ADDITIONAL-TEXT-VARIABLES: { accTrapLogSeqNum,accRipTrapMsg }
PCAUSE-DEFAULT: 7 TRAP-TYPE .1.3.6.1.4.1.5.1.1.16.20.0.21 |
accRipInitFiltPolTrapFailed initializing nbr due to memory shortage.
SEVERITY-DEFAULT: Major
EVENTTYPE-DEFAULT: 10
ADDITIONAL-TEXT-VARIABLES: { accTrapLogSeqNum,accRipTrapMsg }
PCAUSE-DEFAULT: 32 TRAP-TYPE .1.3.6.1.4.1.5.1.1.16.20.0.22 |
accRipInitImpPolTrapIndicates that the function rip_mgr_init_import_policy
returned FALSE.
SEVERITY-DEFAULT: Warning
EVENTTYPE-DEFAULT: 10
ADDITIONAL-TEXT-VARIABLES: { accTrapLogSeqNum,accRipTrapMsg }
PCAUSE-DEFAULT: 7 TRAP-TYPE .1.3.6.1.4.1.5.1.1.16.20.0.23 |
accRipNoNotifIdTrapEach instance of a routing protocol or the IP instance
itself has a bit in the RTH for a change list entry.
The trap indicates that it is due to the inability of
getting bit offset in this field which is reserved for
it in each rt_head in the routing table.
SEVERITY-DEFAULT: Major
EVENTTYPE-DEFAULT: 10
ADDITIONAL-TEXT-VARIABLES: { accTrapLogSeqNum,accRipTrapMsg }
PCAUSE-DEFAULT: 152 TRAP-TYPE .1.3.6.1.4.1.5.1.1.16.20.0.24 |
accRipMaxReTxTrapRetransmission reaches its limit .max_retransmission
period is defined in the profile group.
SEVERITY-DEFAULT: Minor
EVENTTYPE-DEFAULT: 10
ADDITIONAL-TEXT-VARIABLES: { accTrapLogSeqNum,accRipTrapMsg }
PCAUSE-DEFAULT: 7 TRAP-TYPE .1.3.6.1.4.1.5.1.1.16.20.0.25 |
accRipTrapMsgEnterprise Trap Message for rip.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.5.1.1.16.20.1 |