ACC-FR
AI MIB Summary
Standard SNMP MIB module defining data structures for ACC-FR.
70
Objects
Active
Status
3
Dependencies
Imported Objects
Objects
70 total| Object Name |
|---|
accFr OBJECT IDENTIFIER .1.3.6.1.4.1.5.1.1.20 |
IMPORTS Unknown .1.3.6.1.4.1.5.1.1.20 |
accFrAtTableInternet address translation table for Frame
Relay interfaces.
Entries are added/deleted via management action. SEQUENCE OF AccFrAtEntry .1.3.6.1.4.1.5.1.1.20.1 |
accFrAtEntryInternet address translation entry for Frame Relay
interfaces. AccFrAtEntry .1.3.6.1.4.1.5.1.1.20.1.1 |
accFrAtIfIndexInterface number (ifIndex) for which this
translation entry is valid.
Object required in entry-adding SET PDU.rw INTEGER .1.3.6.1.4.1.5.1.1.20.1.1.1 |
accFrIpAddressIP Address
Object required in entry-adding SET PDU.rw IpAddress .1.3.6.1.4.1.5.1.1.20.1.1.2 |
accFrDLCIFrame Relay DLCI to use for the specified host
Object required in entry-adding SET PDU.rw INTEGER .1.3.6.1.4.1.5.1.1.20.1.1.3 |
accFrStatusStatus of this entry
Object required in entry-adding SET PDU.rw Enumeration .1.3.6.1.4.1.5.1.1.20.1.1.4 |
accFrStatTablePer-line statistics for Frame Relay interfaces SEQUENCE OF AccFrStatEntry .1.3.6.1.4.1.5.1.1.20.2 |
accFrStatEntryFrame Relay statistics AccFrStatEntry .1.3.6.1.4.1.5.1.1.20.2.1 |
accFrIndexPhysical Port number of this Frame Relay interface.ro INTEGER .1.3.6.1.4.1.5.1.1.20.2.1.1 |
accFrStatRcvDropsNumber of received frames that were discarded due
to lack of resources.ro Counter .1.3.6.1.4.1.5.1.1.20.2.1.2 |
accFrStatShortsNumber of received frames that were discarded
because they were too short (DLCI and/or
protocol field missing).ro Counter .1.3.6.1.4.1.5.1.1.20.2.1.3 |
accFrStatIllDlcisNumber of received frames that were discarded
because the DLCI was badly formed.ro Counter .1.3.6.1.4.1.5.1.1.20.2.1.4 |
accFrStatUnkDlcisNumber of received frames that were discarded
because the DLCI did not match any configured
value.ro Counter .1.3.6.1.4.1.5.1.1.20.2.1.5 |
accFrStatUnkProtosNumber of received frames that were discarded
because the protocol field did not match any
protocol configured for the specified DLCI.ro Counter .1.3.6.1.4.1.5.1.1.20.2.1.6 |
accFrStatRsrvDlcisNumber of received frames whose DLCI had the
reserved bit set. (The frame was not discarded;
the frame was processed as though the reserved
bit were clear).ro Counter .1.3.6.1.4.1.5.1.1.20.2.1.7 |
accFrStatXmtDropsNumber of frames that could not be transmitted
due to lack of resources.ro Counter .1.3.6.1.4.1.5.1.1.20.2.1.8 |
accFrStatErrTimeSystem uptime when the last Frame Relay error was
detected.ro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.5.1.1.20.2.1.9 |
accFrStatErrTypeType of last detected Frame Relay error.ro Enumeration .1.3.6.1.4.1.5.1.1.20.2.1.10 |
accFrStatErrDlciValue of DLCI field from last detected Frame Relay
error (00 00 if no DLCI was associated with the
last error).ro INTEGER .1.3.6.1.4.1.5.1.1.20.2.1.11 |
accFrStatErrProtoValue of protocol field from last detected Frame
Relay error (0 if no protocol field was associated
with the last error).ro INTEGER .1.3.6.1.4.1.5.1.1.20.2.1.12 |
accFrLinkStateState of this Frame Relay linkro Enumeration .1.3.6.1.4.1.5.1.1.20.2.1.13 |
accFrStatUnksUnused objectro Counter .1.3.6.1.4.1.5.1.1.20.2.1.14 |
accFrStatRcvLongsNumber of received dlcmi frames longer than expected.ro Counter .1.3.6.1.4.1.5.1.1.20.2.1.15 |
accFrStatIlgDlcisUnused objectro Counter .1.3.6.1.4.1.5.1.1.20.2.1.16 |
accFrStatProtoErrsNumber of received frames with a protocol violation.ro Counter .1.3.6.1.4.1.5.1.1.20.2.1.17 |
accFrStatUnkIesNumber of dlcmi frames received with an
unknown Information element.ro Counter .1.3.6.1.4.1.5.1.1.20.2.1.18 |
accFrStatSeqErrsNumber of dlcmi frames received with a
sequence error.ro Counter .1.3.6.1.4.1.5.1.1.20.2.1.19 |
accFrStatUnkRptsUnused objectro Counter .1.3.6.1.4.1.5.1.1.20.2.1.20 |
accFrParmTableFrame Relay parameter table SEQUENCE OF AccFrParmEntry .1.3.6.1.4.1.5.1.1.20.3 |
accFrParmEntryFrame Relay parameter entry AccFrParmEntry .1.3.6.1.4.1.5.1.1.20.3.1 |
accFrParmIndexInterface numberro INTEGER .1.3.6.1.4.1.5.1.1.20.3.1.1 |
accFrParmAddrFmtAddressing format used.
Q.921 per spec. Ignores length parameter
draft-Q922 per March, 1990 draft of Q.922
q922 per October, 1990 Q.922 specificationrw Enumeration .1.3.6.1.4.1.5.1.1.20.3.1.2 |
accFrParmAddrLenLength of address on serial linerw INTEGER .1.3.6.1.4.1.5.1.1.20.3.1.3 |
accFrParmEncapType of encapsulation used on serial linerw Enumeration .1.3.6.1.4.1.5.1.1.20.3.1.4 |
accFrDlcmiStateThis variable states which Data Link Connection
Management scheme is active (and by implication,
what DLCI it uses) on the Frame Relay interface.rw Enumeration .1.3.6.1.4.1.5.1.1.20.3.1.5 |
accFrDlcmiPollIntthe number of seconds between successive
status enquiry messages.rw INTEGER .1.3.6.1.4.1.5.1.1.20.3.1.6 |
accFrDlcmiFullStatEnqNumber of status enquiry intervals that pass
before issuance of a full status enquiry message.rw INTEGER .1.3.6.1.4.1.5.1.1.20.3.1.7 |
accFrDlcmiErrThresMaximum number of unanswered
Status Enquiries the equipmemt shall accept before
declaring the interface down.rw INTEGER .1.3.6.1.4.1.5.1.1.20.3.1.8 |
accFrDlcmiMonEventsMaximum number of responses to
FULL STATUS or LINK INTEGRITY VERIFICATION
messages missed before the device will mark the
interface down.rw INTEGER .1.3.6.1.4.1.5.1.1.20.3.1.9 |
accFrDlcmiTypeLink Maintenance is assymmetrical, so
one end must be user, the other network.
Normally the bridge/router is user.rw Enumeration .1.3.6.1.4.1.5.1.1.20.3.1.10 |
accFrDlcmiIdleTimerNumber of minutes without receiving any
non-dlcmi frames before declaring the link idle.
Setting the timer to 0 will disable it.rw INTEGER .1.3.6.1.4.1.5.1.1.20.3.1.11 |
accFrCktTableFrame Relay circuit table SEQUENCE OF AccFrCktEntry .1.3.6.1.4.1.5.1.1.20.4 |
accFrCktEntryFrame Relay circuit table entry AccFrCktEntry .1.3.6.1.4.1.5.1.1.20.4.1 |
accFrCktIfIndexInterface on which this circuit existsro INTEGER .1.3.6.1.4.1.5.1.1.20.4.1.1 |
accFrCktDlciData Link Connection Identifier for this
circuit.ro INTEGER .1.3.6.1.4.1.5.1.1.20.4.1.2 |
accFrCktStateIndicates whether the particular circuit is
operational.ro Enumeration .1.3.6.1.4.1.5.1.1.20.4.1.3 |
accFrCktFECNrcvdsNumber of frames received from the network in-
dicating forward congestion since the circuit
was created.ro Counter .1.3.6.1.4.1.5.1.1.20.4.1.4 |
accFrCktBECNrcvdsNumber of frames received from the network in-
dicating backward congestion since the circuit
was created.ro Counter .1.3.6.1.4.1.5.1.1.20.4.1.5 |
accFrCktFrameXmtsNumber of frames sent from this circuit
since it was created.ro Counter .1.3.6.1.4.1.5.1.1.20.4.1.6 |
accFrCktOctetXmtsNumber of octets sent from this circuit
since it was created.ro Counter .1.3.6.1.4.1.5.1.1.20.4.1.7 |
accFrCktFrameRcvsNumber of frames received by this circuit
since it was created.ro Counter .1.3.6.1.4.1.5.1.1.20.4.1.8 |
accFrCktOctetRcvsNumber of octets received by this circuit
since it was created.ro Counter .1.3.6.1.4.1.5.1.1.20.4.1.9 |
accFrCktCreateTimeThe value of sysUpTime when the circuit was
created.ro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.5.1.1.20.4.1.10 |
accFrCktChangeTimeThe value of sysUpTime when last there was a
change in the circuit state.ro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.5.1.1.20.4.1.11 |
accFfrCktLoopIndicates the loopback state of the virtual circuit.
The object is normally 'normal', indicating that the
circuit is in its normal operational state. If set
to 'loop', any messages received on the circuit will
be returned unmodified and the circuit will always be
viewed as 'down' by higher layer protocols.
The state of any circuit reverts to 'normal' after
a reset.rw Enumeration .1.3.6.1.4.1.5.1.1.20.4.1.12 |
accFfrSwitchParameterTableFrame Relay Switch Parameter table SEQUENCE OF AccFfrSwitchParameterEntry .1.3.6.1.4.1.5.1.1.20.5 |
accFfrSwitchParameterEntryAn entry in Frame Relay Switch Parameter table AccFfrSwitchParameterEntry .1.3.6.1.4.1.5.1.1.20.5.1 |
accFfrSwitchIfindex1The first interface index in the entryrw INTEGER .1.3.6.1.4.1.5.1.1.20.5.1.1 |
accFfrSwitchDlci1The first Frame Relay DLCI in the entryrw INTEGER .1.3.6.1.4.1.5.1.1.20.5.1.2 |
accFfrSwitchIfindex2The second interface index in the entryrw INTEGER .1.3.6.1.4.1.5.1.1.20.5.1.3 |
accFfrSwitchDlci2The second Frame Relay DLCI in the entryrw INTEGER .1.3.6.1.4.1.5.1.1.20.5.1.4 |
accFfrSwitchStatusThe Status tells whether the traffic will be switched
as per the entry. This object also is usedin the delete
commandrw Enumeration .1.3.6.1.4.1.5.1.1.20.5.1.5 |
accVFRTableTable describing binding between a Virtual port and a Frame Relay
DLCI and a physical port. Entries are added/deleted via management
Action. SEQUENCE OF AccVFRTableEntry .1.3.6.1.4.1.5.1.1.20.6 |
accVFRTableEntryAn entry in the Virtual Frame Relay DLCI Table. AccVFRTableEntry .1.3.6.1.4.1.5.1.1.20.6.1 |
accVFRVirtualPortThe virtual port to be associated with a Physical Port and DLCI.rw INTEGER .1.3.6.1.4.1.5.1.1.20.6.1.1 |
accVFRPhysicalPortThe Physical Port to be associated with a virtual port and dlci.rw INTEGER .1.3.6.1.4.1.5.1.1.20.6.1.2 |
accVFRDlciThe DLCI to be associated with a virtual and physical port.rw INTEGER .1.3.6.1.4.1.5.1.1.20.6.1.3 |
accVFRStatusThe status field indicates if an add or delete
is intended. Invalid = delete; Valid = add.rw Enumeration .1.3.6.1.4.1.5.1.1.20.6.1.4 |