ACC-DS1
AI MIB Summary
Standard SNMP MIB module defining data structures for ACC-DS1.
28
Objects
Active
Status
3
Dependencies
Imported Objects
Objects
28 total| Object Name |
|---|
IMPORTSThe DS1 extension table. SEQUENCE OF AccDs1ExtEntry .1.3.6.1.4.1.5.1.1.42 |
accDs1CircuitTableThe DS1 circuit configuration table. SEQUENCE OF AccDs1CircuitEntry .1.3.6.1.4.1.5.1.1.43 |
accDs1CircuitEntryAn entry in the DS1 circuit configuration table. AccDs1CircuitEntry .1.3.6.1.4.1.5.1.1.43.1 |
accDs1CircuitIndexThis object is the identifier of a circuit on a
managed DS1 interface. It should have the same value
as ifIndex.ro INTEGER -- (1..'7fffffff'h) .1.3.6.1.4.1.5.1.1.43.1.1 |
accDs1CircuitAdiEnables or disables alternate digit inversion for a
circuit on a managed DS1 interface. This object
applies only to E1 interfaces.rw Enumeration .1.3.6.1.4.1.5.1.1.43.1.2 |
accDs1CircuitBandwidthThe bandwidth of the circuit in kilobits per second.rw Enumeration .1.3.6.1.4.1.5.1.1.43.1.3 |
accDs1CircuitBusyoutThe busyout status of a circuit. If the status is
set to busy, the circuit is taken out of service and is
unable to carry user data.rw Enumeration .1.3.6.1.4.1.5.1.1.43.1.4 |
accDs1CircuitInversionEnables or disables circuit inversion for a circuit
on a managed DS1 interface. This object applies only
to T1 interfaces.rw Enumeration .1.3.6.1.4.1.5.1.1.43.1.5 |
accDs1CircuitNameThis object is used to associate a name with a
particular DS1 circuit.rw DisplayString -- .1.3.6.1.4.1.5.1.1.43.1.6 |
accDs1CircuitConfigStatusThis object gives the configuration status for a
circuit entry, and may have the following values:
UNCONFIG The circuit has not been configured
or has been deleted
STATIC The circuit has been configured manually
(stored in NVM)
DYNAMIC The circuit has been configured
automatically (not stored in NVM)rw Enumeration .1.3.6.1.4.1.5.1.1.43.1.7 |
accDs1CircuitLoopbackThis object represents the loopback status of the DS1
circuit. Any active loopback can be removed by
setting the loopback status to none.rw Enumeration .1.3.6.1.4.1.5.1.1.43.1.8 |
accDs1CircuitRbsEnables or disables robbed bit signaling for a
circuit on a managed DS1 interface. This object
applies only to T1 interfaces.rw Enumeration .1.3.6.1.4.1.5.1.1.43.1.9 |
accDs1CircuitSuperrateMaskSpecifies the time-slots used by a superrate
circuit. Each bit which is set corresponds to a
time-slot which is allocated to the superrate
circuit. 2**n-1 corresponds to time-slot n.rw INTEGER -- (0..'7fffffff'h) .1.3.6.1.4.1.5.1.1.43.1.10 |
accDs1ExtEntryAn entry in the DS1 extension table. AccDs1ExtEntry .accDs1ExtTable.1 |
accDs1ExtLineIndexThis object is the identifier of a DS1 Interface on a
managed device. It has the same value as dsx1LineIndex.ro INTEGER -- (1..'7fffffff'h) .accDs1ExtTable.1.1 |
accDs1ExtLineLengthThe approximate line length. When equipped with a
DSX1 line interface module, this object selects the
transmit equalization. When equipped with a CSU
interface module, this object selects the line build
out (LBO).rw Enumeration .accDs1ExtTable.1.2 |
accDS1ExtNfasGroupThe ifIndex of another DS1 interface whose common
signaling channel (e.g., ISDN D channel) carries
signaling information for this DS1 interface.rw INTEGER -- (0..'7fffffff'h) .accDs1ExtTable.1.3 |
accDs1ExtInterfaceIdThe internal interface on which signalling is received.
0 indicates the D-channel.rw INTEGER .accDs1ExtTable.1.4 |
accDs1ExtE1TypeThe type of E1 equipment to which the device is connected.
Only used to work around Nordic type switch anomolies.rw Enumeration .accDs1ExtTable.1.5 |
accDs1ExtXcvrThe type of transceiver installed.rw Enumeration .accDs1ExtTable.1.6 |
accDs1ExtPrecedenceWhen the interface is provisioned as a PRI interface with
D-channel backup, this object determines whether the D
channel on this interface is the primary or secondary D
channel.rw Enumeration .accDs1ExtTable.1.7 |
accDs1ExtSignalGroupThe index of the Signal group assigned to this interface.
The value of the trunk group index is limited to the
maximum number of PRI interfaces that can be installed on
a given platform (3 for Amazon, 28 for Tigris). A trunk
group value of 0 indicates that the interface does not belong
to a PRI trunk group. Replaces accDs1ExtNfasGroup which
has been deprecated.rw INTEGER .accDs1ExtTable.1.8 |
accDs1ExtNumberGroupThe index of the called number group assigned to this
interface. Number groups are defined in the Called Number
Table. A number group value of 0 indicates that no called
number group has been assigned to this interface.rw INTEGER .accDs1ExtTable.1.9 |
accDs1ExtIntegAccessIndicates whether this interface has enabled integrated
access. If enabled, the signal group is used as the
signaling channel for this interface.rw Enumeration .accDs1ExtTable.1.10 |
accDs1ExtSignalModeSignaling mode for this DS1 interfacerw Enumeration .accDs1ExtTable.1.11 |
accDs1ExtCICBaseCIC base to use for circuits on this DS1 interface.rw INTEGER .accDs1ExtTable.1.12 |
accDs1ExtMessageLevelMaintenance message level for this DS1 interface.rw INTEGER .accDs1ExtTable.1.13 |
accDs1ExtServiceStateDescribes DS1 service state. Certain attributes
need to be in a specific state to be changed.ro Enumeration .accDs1ExtTable.1.14 |