A3COM-HUAWEI-RPR-MIB
AI MIB Summary
The A3COM-HUAWEI-RPR-MIB module monitors and configures Resilient Packet Ring (RPR) interface parameters and alarm states on A3Com and Huawei networking devices, specifically tracking the operational status of the dual-fiber outer and inner ring topology.
This MIB manages RPR(Resilient Packet Ring)interfaces by providing an operational table which controls parameters of each RPR interface and reports alarm conditions. A RPR ring is composed of two fiber rings: Outer and Inner.
Main OID:
h3cRpr.1.3.6.1.4.1.43.45.1.10.2.60
130
Objects
Active
Status
6
Dependencies
Imported Objects
Objects
130 total| Object Name |
|---|
h3cRprThis MIB manages RPR(Resilient Packet Ring)interfaces by providing an operational table which controls parameters of each RPR interface and reports alarm conditions. A RPR ring is composed of two fiber rings: Outer and Inner. MODULE-IDENTITY .1.3.6.1.4.1.43.45.1.10.2.60 |
h3cRprObjects OBJECT IDENTIFIER .1.3.6.1.4.1.43.45.1.10.2.60.1 |
h3cRprMaxmumDefine OBJECT IDENTIFIER .1.3.6.1.4.1.43.45.1.10.2.60.1.1 |
h3cRprMaxmumDefineTableThis table contains the specs of RPR ring. SEQUENCE OF H3cRprMaxmumDefineEntry .1.3.6.1.4.1.43.45.1.10.2.60.1.1.1 |
h3cRprMaxmumDefineEntryThe entry of RPR Maximum Table. H3cRprMaxmumDefineEntry .1.3.6.1.4.1.43.45.1.10.2.60.1.1.1.1 |
h3cRprMaxMumIfIndexThe ifIndex of this RPR interface. InterfaceIndex (IF-MIB) .1.3.6.1.4.1.43.45.1.10.2.60.1.1.1.1.1 |
h3cRprMaxStationNumDefineMax station number supported by RPR ring.ro INTEGER .1.3.6.1.4.1.43.45.1.10.2.60.1.1.1.1.2 |
h3cRprMaxReservedRateDefineMax reserved rate supported by each RPR ringlet. An estimate of the interface's current bandwidth in units of 1,000,000 bits per second. If this object reports a value of 'n' then the speed of the interface is somewhere in the range of 'n-500,000' to 'n+499,999'. For interfaces which do not vary in bandwidth or for those where no accurate estimation can be made, this object should contain the nominal bandwidth. For a sub-layer which has no concept of bandwidth, this object should be zero.ro Gauge32 .1.3.6.1.4.1.43.45.1.10.2.60.1.1.1.1.3 |
h3cRprTopoImage OBJECT IDENTIFIER .1.3.6.1.4.1.43.45.1.10.2.60.1.2 |
h3cRprTopoImageXTableThis table contains additional objects for the rprTopoImageTable in IEEE-802DOT17-RPR-MIB. SEQUENCE OF H3cRprTopoImageXEntry .1.3.6.1.4.1.43.45.1.10.2.60.1.2.1 |
h3cRprTopoImageXEntryEach entry contains information specific to a particular station on the ring. The table has at least one entry for the station itself, this entry indicates zero hops on each ringlet. H3cRprTopoImageXEntry .1.3.6.1.4.1.43.45.1.10.2.60.1.2.1.1 |
h3cRprTopoImageXWestEdgeStatusThe current edge status of the west span. If an edge exists,the h3cRprTopoImageXWestEdgeStatus is true. Otherwise, the h3cRprTopoImageXWestEdgeStatus is false.ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.43.45.1.10.2.60.1.2.1.1.3 |
h3cRprTopoImageXEastEdgeStatusThe current edge status of the east span. If an edge exists, the h3cRprTopoImageXEastEdgeStatus is true. Otherwise, the h3cRprTopoImageXEastEdgeStatus is false.ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.43.45.1.10.2.60.1.2.1.1.4 |
h3cRprTopoImageXStationNameThe operator assigned station name. The operator can assigned it by h3cRprTopoImageXStationName.rw SnmpAdminString (SNMP-FRAMEWORK-MIB) .1.3.6.1.4.1.43.45.1.10.2.60.1.2.1.1.5 |
h3cRprSpanCounters OBJECT IDENTIFIER .1.3.6.1.4.1.43.45.1.10.2.60.1.3 |
h3cRprSrcMacCountTableThe RPR Source Mac Count Table contains the cumulative sum of frames and octects from the particular source station. SEQUENCE OF H3cRprSrcMacCountEntry .1.3.6.1.4.1.43.45.1.10.2.60.1.3.1 |
h3cRprSrcMacCountEntryAn entry in the RPR Source Mac Count Table. H3cRprSrcMacCountEntry .1.3.6.1.4.1.43.45.1.10.2.60.1.3.1.1 |
h3cRprSrcMacCountIfIndexThe ifIndex of this RPR interface. InterfaceIndex (IF-MIB) .1.3.6.1.4.1.43.45.1.10.2.60.1.3.1.1.1 |
h3cRprSrcMacCountBySrcAddressMAC address of the source station where the frames come from. MacAddress (SNMPv2-TC) .1.3.6.1.4.1.43.45.1.10.2.60.1.3.1.1.2 |
h3cRprSrcMacCountReceivedFramesFrames received from a particular MAC address of source station.ro Counter64 .1.3.6.1.4.1.43.45.1.10.2.60.1.3.1.1.3 |
h3cRprSrcMacCountReceivedOctetsOctets received from a particular MAC address of source station.ro Counter64 .1.3.6.1.4.1.43.45.1.10.2.60.1.3.1.1.4 |
h3cRprDestMacCountTableThe RPR Destination MAC Count Table contains the cumulative sum of frames and octects to the particular destination station. SEQUENCE OF H3cRprDestMacCountEntry .1.3.6.1.4.1.43.45.1.10.2.60.1.3.2 |
h3cRprDestMacCountEntryAn entry in the RPR MAC Destination Count Table. H3cRprDestMacCountEntry .1.3.6.1.4.1.43.45.1.10.2.60.1.3.2.1 |
h3cRprDestMacCountIfIndexThe ifIndex of RPR interface. InterfaceIndex (IF-MIB) .1.3.6.1.4.1.43.45.1.10.2.60.1.3.2.1.1 |
h3cRprDestMacCountByDestAddressMAC address of the destination station where the frames are sent to. MacAddress (SNMPv2-TC) .1.3.6.1.4.1.43.45.1.10.2.60.1.3.2.1.2 |
h3cRprDestMacCountReceivedFramesFrames sent to a particular MAC address of destination station.ro Counter64 .1.3.6.1.4.1.43.45.1.10.2.60.1.3.2.1.3 |
h3cRprDestMacCountReceivedOctetsOctets sent to a particular MAC address of destination station.ro Counter64 .1.3.6.1.4.1.43.45.1.10.2.60.1.3.2.1.4 |
h3cRprPktDropCountTableThe RPR Packet Drop Count Table contains the cumulative sum of packets dropped for congestion. SEQUENCE OF H3cRprPktDropCountEntry .1.3.6.1.4.1.43.45.1.10.2.60.1.3.3 |
h3cRprPktDropCountEntryAn entry in the RPR Packet Drop Count Table. H3cRprPktDropCountEntry .1.3.6.1.4.1.43.45.1.10.2.60.1.3.3.1 |
h3cRprPktDropCntIfIndexThe ifIndex of this RPR interface. InterfaceIndex (IF-MIB) .1.3.6.1.4.1.43.45.1.10.2.60.1.3.3.1.1 |
h3cRprPktDropCntRingletIDThe RPR Ringlet of the station through which the packets transmit. H3cRprRingletID .1.3.6.1.4.1.43.45.1.10.2.60.1.3.3.1.2 |
h3cRprDownFlowClassAPktDropsThe total dropped number of Class A packets which transmit down from the host.ro Counter64 .1.3.6.1.4.1.43.45.1.10.2.60.1.3.3.1.3 |
h3cRprUpFlowClassAPktDropsThe total dropped number of Class A packets which transmit up to the host.ro Counter64 .1.3.6.1.4.1.43.45.1.10.2.60.1.3.3.1.4 |
h3cRprDownFlowClassBPktDropsThe total dropped number of Class B packets which transmit down from the host.ro Counter64 .1.3.6.1.4.1.43.45.1.10.2.60.1.3.3.1.5 |
h3cRprUpFlowClassBPktDropsThe total dropped number of Class B packets which transmit up to the host.ro Counter64 .1.3.6.1.4.1.43.45.1.10.2.60.1.3.3.1.6 |
h3cRprDownFlowClassCPktDropsThe total dropped number of Class C packets which transmit down from the host.ro Counter64 .1.3.6.1.4.1.43.45.1.10.2.60.1.3.3.1.7 |
h3cRprUpFlowClassCPktDropsThe total dropped number of Class C packets which transmit up to the host.ro Counter64 .1.3.6.1.4.1.43.45.1.10.2.60.1.3.3.1.8 |
h3cRprRS OBJECT IDENTIFIER .1.3.6.1.4.1.43.45.1.10.2.60.1.4 |
h3cRprStaticRSTableThe RPR Static Ring Selection table contains the static ring selection information by the way of configuration. SEQUENCE OF H3cRprStaticRSEntry .1.3.6.1.4.1.43.45.1.10.2.60.1.4.1 |
h3cRprStaticRSEntryAn entry in the RPR Static Ring Selection table. H3cRprStaticRSEntry .1.3.6.1.4.1.43.45.1.10.2.60.1.4.1.1 |
h3cRprStaticRSIfIndexThe ifIndex of RPR interface. InterfaceIndex (IF-MIB) .1.3.6.1.4.1.43.45.1.10.2.60.1.4.1.1.1 |
h3cRprStaticRSMacAddressThe MAC address of the station on the ring. MacAddress (SNMPv2-TC) .1.3.6.1.4.1.43.45.1.10.2.60.1.4.1.1.2 |
h3cRprStaticRSRingletIDThe identifier of the ring which frames are sent from one station to another. Ringlet0 refers to outer ring, while ringlet1 does inner.rw H3cRprRingletID .1.3.6.1.4.1.43.45.1.10.2.60.1.4.1.1.3 |
h3cRprStaticRSTtlThe hops from source station to destination station by the selected ringlet.ro INTEGER .1.3.6.1.4.1.43.45.1.10.2.60.1.4.1.1.4 |
h3cRprStaticRSValidThe flag identify whether the configed ringlet is valid. If it is true, the configed ringlet is valid, otherwise it's invalid.ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.43.45.1.10.2.60.1.4.1.1.5 |
h3cRprStaticRSRowStatusThe status of this table entry. The status includes createAndGo, active and destroy.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.43.45.1.10.2.60.1.4.1.1.6 |
h3cRprIpv4DynamicRSTableThe RPR Ipv4Dynamic Ring Selection Table that contains the dynamic ring selection information by shortest path. SEQUENCE OF H3cRprIpv4DynamicRSEntry .1.3.6.1.4.1.43.45.1.10.2.60.1.4.2 |
h3cRprIpv4DynamicRSEntryAn entry in the RPR Ipv4Dynamic Ring Selection Table. H3cRprIpv4DynamicRSEntry .1.3.6.1.4.1.43.45.1.10.2.60.1.4.2.1 |
h3cRprIpv4DynamicRSIfIndexThe ifIndex of RPR interface. InterfaceIndex (IF-MIB) .1.3.6.1.4.1.43.45.1.10.2.60.1.4.2.1.1 |
h3cRprIpv4DynamicRSMacAddressThe Ipv4 MAC address of destination station on the ring. MacAddress (SNMPv2-TC) .1.3.6.1.4.1.43.45.1.10.2.60.1.4.2.1.2 |
h3cRprIpv4DynamicRSRingletIDThe identifier of the ring which frames are sent from the source station to the destination station.ro H3cRprRingletID .1.3.6.1.4.1.43.45.1.10.2.60.1.4.2.1.3 |
h3cRprIpv4DynamicRSTtlThe hops from source station to destination station by the selected ringlet.ro INTEGER .1.3.6.1.4.1.43.45.1.10.2.60.1.4.2.1.4 |
h3cRprIpv6DynamicRSTableThe RPR Ipv6 Dynamic Ring Selection Table that contains the Ipv6 ring selection information by dynamic ring selection and static ring selection. SEQUENCE OF H3cRprIpv6DynamicRSEntry .1.3.6.1.4.1.43.45.1.10.2.60.1.4.3 |
h3cRprIpv6DynamicRSEntryAn entry in the RPR Ipv6 Ring Selection Table. H3cRprIpv6DynamicRSEntry .1.3.6.1.4.1.43.45.1.10.2.60.1.4.3.1 |
h3cRprIpv6DynamicRSIfIndexThe ifIndex of RPR interface. InterfaceIndex (IF-MIB) .1.3.6.1.4.1.43.45.1.10.2.60.1.4.3.1.1 |
h3cRprIpv6DynamicRSMacAddressThe Ipv6 MAC address of the destination station on the ring. MacAddress (SNMPv2-TC) .1.3.6.1.4.1.43.45.1.10.2.60.1.4.3.1.2 |
h3cRprIpv6DynamicRSRingletIDThe identifier of the ring which frames are sent from the source station to the destination station.ro H3cRprRingletID .1.3.6.1.4.1.43.45.1.10.2.60.1.4.3.1.3 |
h3cRprIpv6DynamicRSTtlThe hops from source station to destination station by selected ringlet.ro INTEGER .1.3.6.1.4.1.43.45.1.10.2.60.1.4.3.1.4 |
h3cRprIpv4OverallRSTableThe RPR Ipv4 Overall Ring Selection Table that contains the overall and active ring selection infomation by dynamic ring selection and static ring selection. SEQUENCE OF H3cRprIpv4OverallRSEntry .1.3.6.1.4.1.43.45.1.10.2.60.1.4.4 |
h3cRprIpv4OverallRSEntryAn entry in the RPR Overall Ring Selection Table. H3cRprIpv4OverallRSEntry .1.3.6.1.4.1.43.45.1.10.2.60.1.4.4.1 |
h3cRprIpv4OverallRSIfIndexThe ifIndex of RPR interface. InterfaceIndex (IF-MIB) .1.3.6.1.4.1.43.45.1.10.2.60.1.4.4.1.1 |
h3cRprIpv4OverallRSMacAddressThe MAC address of the destination station on the ring. MacAddress (SNMPv2-TC) .1.3.6.1.4.1.43.45.1.10.2.60.1.4.4.1.2 |
h3cRprIpv4OverallRSTypeThe ring selection item type indicates static or dynamic.ro Enumeration .1.3.6.1.4.1.43.45.1.10.2.60.1.4.4.1.3 |
h3cRprIpv4OverallRSRingletIDThe identifier of the ring which frames are sent from the source station to the destination station.ro H3cRprRingletID .1.3.6.1.4.1.43.45.1.10.2.60.1.4.4.1.4 |
h3cRprIpv4OverallRSTtlThe hops from source station to destination station by selected ringlet.ro INTEGER .1.3.6.1.4.1.43.45.1.10.2.60.1.4.4.1.5 |
h3cRprVrrpRSTableThe RPR VRRP Ring Selection Table that contains the ring selection information when the vrrp group is configured. SEQUENCE OF H3cRprVrrpRSEntry .1.3.6.1.4.1.43.45.1.10.2.60.1.4.5 |
h3cRprVrrpRSEntryAn entry in the RPR VRRP Ring Selection Table. H3cRprVrrpRSEntry .1.3.6.1.4.1.43.45.1.10.2.60.1.4.5.1 |
h3cRprVrrpRSIfIndexThe ifIndex of RPR interface. InterfaceIndex (IF-MIB) .1.3.6.1.4.1.43.45.1.10.2.60.1.4.5.1.1 |
h3cRprVrrpRSVirtualMacAddressThe virtual MAC address of the staion in VRRP group. MacAddress (SNMPv2-TC) .1.3.6.1.4.1.43.45.1.10.2.60.1.4.5.1.2 |
h3cRprVrrpRSMacAddressThe MAC address of the station that is the master in VRRP group.ro MacAddress (SNMPv2-TC) .1.3.6.1.4.1.43.45.1.10.2.60.1.4.5.1.3 |
h3cRprVrrpRSRingletIDThe identifier of the ring which frames are sent from the source station to the destination station.ro H3cRprRingletID .1.3.6.1.4.1.43.45.1.10.2.60.1.4.5.1.4 |
h3cRprVrrpRSTtlThe hops from source station to destination station by selected ringlet.ro INTEGER .1.3.6.1.4.1.43.45.1.10.2.60.1.4.5.1.5 |
h3cRprDefaultRingIDTableThe RPR Default RingID Table specify the default ringID. SEQUENCE OF H3cRprDefaultRingIDEntry .1.3.6.1.4.1.43.45.1.10.2.60.1.4.6 |
h3cRprDefaultRingIDEntryAn entry in the RPR Default RingID Table. H3cRprDefaultRingIDEntry .1.3.6.1.4.1.43.45.1.10.2.60.1.4.6.1 |
h3cRprDefaultRingIDIfIndexThe ifIndex of RPR interface. InterfaceIndex (IF-MIB) .1.3.6.1.4.1.43.45.1.10.2.60.1.4.6.1.1 |
h3cRprDefaultConfigRingletIDThe default identifier of the ring configured by user.rw H3cRprRingletID .1.3.6.1.4.1.43.45.1.10.2.60.1.4.6.1.2 |
h3cRprDefaultActiveRingIDThe identifier of the default ring which is active currently. The default ring configured by user may be inactive.ro H3cRprRingletID .1.3.6.1.4.1.43.45.1.10.2.60.1.4.6.1.3 |
h3cRprDefect OBJECT IDENTIFIER .1.3.6.1.4.1.43.45.1.10.2.60.1.5 |
h3cRprDefectReportTableThe RPR Defect Report Table that contains the trap information on the ring. SEQUENCE OF H3cRprDefectReportEntry .1.3.6.1.4.1.43.45.1.10.2.60.1.5.1 |
h3cRprDefectReportEntryAn entry in the RPR Defect Report Table. H3cRprDefectReportEntry .1.3.6.1.4.1.43.45.1.10.2.60.1.5.1.1 |
h3cRprDefectIfIndexThe ifIndex of RPR interface. InterfaceIndex (IF-MIB) .1.3.6.1.4.1.43.45.1.10.2.60.1.5.1.1.1 |
h3cRprDefectCurrentStatusIndicates the current status of RPR ring. This attribute is used to notify the management system that alarms generate or clear about some RPR ring.ro Bits .1.3.6.1.4.1.43.45.1.10.2.60.1.5.1.1.2 |
h3cRprPriorityMap OBJECT IDENTIFIER .1.3.6.1.4.1.43.45.1.10.2.60.1.6 |
h3cRprPriority2ClassMapTableThe Table is for Class Of Service and RPR Service Class Mapping. SEQUENCE OF H3cRprPriority2ClassMapEntry .1.3.6.1.4.1.43.45.1.10.2.60.1.6.1 |
h3cRprPriority2ClassMapEntryAn entry in the COS to Service Class Map Table. H3cRprPriority2ClassMapEntry .1.3.6.1.4.1.43.45.1.10.2.60.1.6.1.1 |
h3cRprPriority2ClassMapIfIndexThe ifIndex of RPR interface. InterfaceIndex (IF-MIB) .1.3.6.1.4.1.43.45.1.10.2.60.1.6.1.1.1 |
h3cRprPriority2ClassMapTypeThe type of Priority,include tag, mpls, ip. Enumeration .1.3.6.1.4.1.43.45.1.10.2.60.1.6.1.1.2 |
h3cRprPriorityValueThe priority of tag,mpls and ip, the value range is 0~7. Enumeration .1.3.6.1.4.1.43.45.1.10.2.60.1.6.1.1.3 |
h3cRprPriority2ClassMapThe RPR service class.rw H3cRprServiceClass .1.3.6.1.4.1.43.45.1.10.2.60.1.6.1.1.4 |
h3cRprRateLimitConfig OBJECT IDENTIFIER .1.3.6.1.4.1.43.45.1.10.2.60.1.7 |
h3cRprRateLimitConfigTableThe RPR Rate Limit Configuration Table that contains the rate limit infomation of RPR serviec class. SEQUENCE OF H3cRprRateLimitConfigEntry .1.3.6.1.4.1.43.45.1.10.2.60.1.7.1 |
h3cRprRateLimitConfigEntryAn entry in the RPR Rate Limit Configuration Table. H3cRprRateLimitConfigEntry .1.3.6.1.4.1.43.45.1.10.2.60.1.7.1.1 |
h3cRprRateLimitConfigIfIndexThe ifIndex of RPR interface. InterfaceIndex (IF-MIB) .1.3.6.1.4.1.43.45.1.10.2.60.1.7.1.1.1 |
h3cRprRateLimitConfigRingletIdThe identifier of the ring of RPR ringlet. H3cRprRingletID .1.3.6.1.4.1.43.45.1.10.2.60.1.7.1.1.2 |
h3cRprRateLimitConfigServiceClassThe RPR service class. H3cRprServiceClass .1.3.6.1.4.1.43.45.1.10.2.60.1.7.1.1.3 |
h3cRprRateLimitConfigValueThe value of rate-limit that configured for diffrent service class. The unit is permillage.rw Integer32 .1.3.6.1.4.1.43.45.1.10.2.60.1.7.1.1.4 |
h3cRprMacAddrLearn OBJECT IDENTIFIER .1.3.6.1.4.1.43.45.1.10.2.60.1.8 |
h3cRprMacLearnCfgTableThe RPR MAC Address Table. SEQUENCE OF H3cRprMacLearnCfgEntry .1.3.6.1.4.1.43.45.1.10.2.60.1.8.1 |
h3cRprMacLearnCfgEntryThe entry of RPR MAC Address Table. H3cRprMacLearnCfgEntry .1.3.6.1.4.1.43.45.1.10.2.60.1.8.1.1 |
h3cRprMacLearnIfIndexThe ifIndex of RPR interface. InterfaceIndex (IF-MIB) .1.3.6.1.4.1.43.45.1.10.2.60.1.8.1.1.1 |
h3cRprMacLearnRprMacThe MAC address of the RPR station. MacAddress (SNMPv2-TC) .1.3.6.1.4.1.43.45.1.10.2.60.1.8.1.1.2 |
h3cRprMacLearnTypeThe type of MAC address item that the user built. The type includes static and dynamic.rw INTEGER .1.3.6.1.4.1.43.45.1.10.2.60.1.8.1.1.3 |
h3cRprMacLearnDestMacThe destination of MAC address.rw MacAddress (SNMPv2-TC) .1.3.6.1.4.1.43.45.1.10.2.60.1.8.1.1.4 |
h3cRprMacLearnVlanIdThe vlan ID that the MAC address learned from by RPR staion.rw Integer32 .1.3.6.1.4.1.43.45.1.10.2.60.1.8.1.1.5 |
h3cRprMacLearnRingletThe identifier of the ring which frames are sent from the source station to the destination station.rw H3cRprRingletID .1.3.6.1.4.1.43.45.1.10.2.60.1.8.1.1.6 |
h3cRprMacLearnTtlThe hops from source station to destination station on the selected ringlet.ro INTEGER .1.3.6.1.4.1.43.45.1.10.2.60.1.8.1.1.7 |
h3cRprMacLearnIsValidThe flag identify whether the configured mac address is valid. If it is true, the configured mac address is valid, otherwise it's invalid.ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.43.45.1.10.2.60.1.8.1.1.8 |
h3cRprMacLearnRowStatusThe status of this table entry. The status includes createAndGo, active and destroy.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.43.45.1.10.2.60.1.8.1.1.9 |
h3cRprTrapVar OBJECT IDENTIFIER .1.3.6.1.4.1.43.45.1.10.2.60.1.9 |
h3cRprTrapVarTableThe RPR Defect Report Table that contains varible that used to bind in trap. SEQUENCE OF H3cRprTrapVarEntry .1.3.6.1.4.1.43.45.1.10.2.60.1.9.1 |
h3cRprTrapVarEntryAn entry in the RPR Trap Var Table. H3cRprTrapVarEntry .1.3.6.1.4.1.43.45.1.10.2.60.1.9.1.1 |
h3cRprTrapIfIndexThe ifIndex of RPR interface. It is only used for trap to bind.ro InterfaceIndex (IF-MIB) .1.3.6.1.4.1.43.45.1.10.2.60.1.9.1.1.1 |
h3cRprTrapRingletThe span of RPR station. It is only used for trap to bind.ro H3cRprRingletID .1.3.6.1.4.1.43.45.1.10.2.60.1.9.1.1.2 |
h3cRprTrapTopoMacAddressThe MAC address of RPR station. It is only used for trap to bind.ro MacAddress (SNMPv2-TC) .1.3.6.1.4.1.43.45.1.10.2.60.1.9.1.1.3 |
h3cRprTrapIpAddressThe IP address of RPR station. It is only used for trap to bind.ro InetAddress .1.3.6.1.4.1.43.45.1.10.2.60.1.9.1.1.4 |
h3cRprTrap OBJECT IDENTIFIER .1.3.6.1.4.1.43.45.1.10.2.60.1.10 |
h3cRprTopologyOpenRingThe topology openRing trap indicates that the RPR ring is opened. NOTIFICATION-TYPE .1.3.6.1.4.1.43.45.1.10.2.60.1.10.1 |
h3cRprTopologyCloseRingThe topology openRing trap indicates that the RPR ring is closed. NOTIFICATION-TYPE .1.3.6.1.4.1.43.45.1.10.2.60.1.10.2 |
h3cRprTopologyInconsistentThe topology inconsistent trap indicates that the topology of RPR is inconsistent. NOTIFICATION-TYPE .1.3.6.1.4.1.43.45.1.10.2.60.1.10.3 |
h3cRprTopologyInstabilityThe topology instability trap indicates that the topology of RPR is instability. NOTIFICATION-TYPE .1.3.6.1.4.1.43.45.1.10.2.60.1.10.4 |
h3cRprDuplicateMacAddressThe duplicate MAC address trap indicates that the mac address of the station on the ring is dulplicate. That means there is the same MAC address between two stations on the ring. NOTIFICATION-TYPE .1.3.6.1.4.1.43.45.1.10.2.60.1.10.5 |
h3cRprDulplicateIPAddressThe dulplicate IP address trap indicates that the IP address of the station on the ring is dulplicate. That means there is the same IP address between two stations on the ring. NOTIFICATION-TYPE .1.3.6.1.4.1.43.45.1.10.2.60.1.10.6 |
h3cRprIncompleteLRTTThe incomplete LRTT trap indicates that LRTT is not completed. NOTIFICATION-TYPE .1.3.6.1.4.1.43.45.1.10.2.60.1.10.7 |
h3cRprProtecConfigInconsistentThe protection configuration inconsistent trap indicates that the configuration of protection mode on the ring is inconsistent. That is one station is configured steer mode while the other is configured wrap mode. NOTIFICATION-TYPE .1.3.6.1.4.1.43.45.1.10.2.60.1.10.8 |
h3cRprJumboConfigInconsistentThe jumbo configuration inconsistent trap indicates that the configuration of jumbo mode on the ring is inconsistent. That is one station supports jumbo frame while the other doesn't support jumbo frame. NOTIFICATION-TYPE .1.3.6.1.4.1.43.45.1.10.2.60.1.10.9 |
h3cRprExceedMaxReservRateThe exceeded max reserved rate trap indicates that the rate on the ringlet exceeded the max reserved rate. The operator can configure reserved rate for every station, but the sum of all stations' reserved rate of each RPR ringlet can't exceed maximum. NOTIFICATION-TYPE .1.3.6.1.4.1.43.45.1.10.2.60.1.10.10 |
h3cRprExceedMaxStationNumThe exceeded max station number trap indicates that the number of the stations on the ring exceeded the max station number. NOTIFICATION-TYPE .1.3.6.1.4.1.43.45.1.10.2.60.1.10.11 |
h3cRprMiscablingThe miscabling trap indicates that the miscabling event occurred. NOTIFICATION-TYPE .1.3.6.1.4.1.43.45.1.10.2.60.1.10.12 |
h3cRprBackPressureThe back pressure trap indicates that the backpressure is generated on the ringlet. That is the data flow on the ringlet exceeded the range of rate-limit configured. NOTIFICATION-TYPE .1.3.6.1.4.1.43.45.1.10.2.60.1.10.13 |
h3cRprBackPressureOverThe back pressure over trap indicates that the backpressure is disappeared on the ringlet. NOTIFICATION-TYPE .1.3.6.1.4.1.43.45.1.10.2.60.1.10.14 |