cp4100
Crossroads private mib for 4100 and 4200 Fibre Channel to SCSI Router.
Main OID:
crossroads.1.3.6.1.4.1.2512
109
Objects
Active
Status
3
Dependencies
Imported Objects
Objects
109 total| Object Name |
|---|
crossroadsCrossroads private mib for 4100 and 4200
Fibre Channel to SCSI Router. MODULE-IDENTITY .1.3.6.1.4.1.2512 |
SNMPv2-SMICrossroads private mib for 4100 and 4200
Fibre Channel to SCSI Router. Unknown .1.3.6.1.4.1.2512 |
crossroads4000series OBJECT IDENTIFIER .1.3.6.1.4.1.2512.1 |
crossroads4100 OBJECT IDENTIFIER .1.3.6.1.4.1.2512.1.1 |
fcConfigNodeNameWorldwide name of a collection
of N_Ports that comprise a Node.rw WorldwideName .1.3.6.1.4.1.2512.1.1.1 |
fcConfigNodeNumNPortsNumber of N_Ports that
comprise the named Node.ro INTEGER .1.3.6.1.4.1.2512.1.1.2 |
fcConfig OBJECT IDENTIFIER .1.3.6.1.4.1.2512.1.1.3 |
fcConfigEnableResetToggle for software reset.
True indicates that ressetting the
product via SNMP is allowed.
NOTE: each time the product is
initialized this object is set to
FALSE (i.e. it is not sticky).rw Boolean .1.3.6.1.4.1.2512.1.1.3.1 |
fcConfigUseHardAddressToggle for address configuration.
True indicates that configuration
of the source ID is allowed.
False indicates that the source ID
may not be changed.rw Boolean .1.3.6.1.4.1.2512.1.1.3.2 |
fcConfigSourceID3 byte Source address.
For arbitrated loop, this will be the
Hard Assigned AL_PA (preceeded by 2 0 bytes).
ex. 0.0.EFrw SourceID .1.3.6.1.4.1.2512.1.1.3.3 |
fcConfigSCSIModeFibre Channel to SCSI mapping mode.rw Enumeration .1.3.6.1.4.1.2512.1.1.3.4 |
fcConfigTraceMaskTrace Level.rw INTEGER (0 .. 255) .1.3.6.1.4.1.2512.1.1.3.5 |
fcConfigResetReset the product. Setting this object
to TRUE will re-start all the software
(similar to powering the product off, then
on). The reset will only take place if
fcConfigResetEnable is also TRUE.
NOTE: resetting the product will disconnect
all current Fibre Channel connections.rw Boolean .1.3.6.1.4.1.2512.1.1.3.6 |
fcConfigCommitCommit the configuration values
to the flash memory.rw Boolean .1.3.6.1.4.1.2512.1.1.3.7 |
fcConfigFirmwareRevLevelFirmware revision level.ro OCTET STRING .1.3.6.1.4.1.2512.1.1.3.8 |
mi OBJECT IDENTIFIER .1.3.6.1.4.1.2512.1.1.4 |
miSerialBaudRateThe baud rate for the serial interface.rw Enumeration .1.3.6.1.4.1.2512.1.1.4.1 |
miMACAddressPhysical address (MAC address).rw OCTET STRING .1.3.6.1.4.1.2512.1.1.4.2 |
miethernetIPAddrThe IP address for this device.rw OCTET STRING .1.3.6.1.4.1.2512.1.1.4.3 |
miethernetIPNetmaskEthernet Net Mask.rw OCTET STRING .1.3.6.1.4.1.2512.1.1.4.4 |
miTrapIPAddrThe IP address used for sending traps.
Typically this is the IP address of the
machine which has a network management
program and/or MIB browser.rw OCTET STRING .1.3.6.1.4.1.2512.1.1.4.5 |
miTrapEnableEnable/Disable Traps.
If TRUE, traps are sent to the specified
Trap IP Address.
If disabled, no traps will be sent to
the SNMP manager.rw Boolean .1.3.6.1.4.1.2512.1.1.4.6 |
miTrapPriorityThe Trap Priority.
All SNMP Events (traps) of this
priority (or higher) will be sent
to the specified Trap IP Address.rw Enumeration .1.3.6.1.4.1.2512.1.1.4.7 |
scsiConfigTableA Table containing SCSI Configuration parameters. SEQUENCE OF SCSIConfigEntry .1.3.6.1.4.1.2512.1.1.5 |
scsiConfigEntryAn entry in the SCSI Configuration Table. SCSIConfigEntry .1.3.6.1.4.1.2512.1.1.5.1 |
scsiConfigIndexIndex into the SCSI Configuration Table.ro INTEGER .1.3.6.1.4.1.2512.1.1.5.1.1 |
scsiConfigInitIDInitiator SCSI ID.rw INTEGER .1.3.6.1.4.1.2512.1.1.5.1.2 |
scsiConfigTargetIDAddGet will return a mask of SCSI
target ID's. A mask has a bit set for
each target ID which is in use. Example:
Get returns 133 = 0x0085 = 0000 0000 1000 0101
indicating target ID's are 7, 2 and 0.
Set allows you to set SCSI target ID's,
by setting the appropriate bit in the mask.
NOTE: this object only allows you to Add targets,
a 0 in the mask will not remove a target.rw INTEGER .1.3.6.1.4.1.2512.1.1.5.1.3 |
scsiConfigTargetIDRemoveGet will return a mask of SCSI
target ID's. A mask has a bit set for
each target ID which is in use. Example:
Get returns 133 = 0x0085 = 0000 0000 1000 0101
indicating target ID's are 7, 2 and 0.
Set allows you to remove SCSI target ID's,
by setting the appropriate bit in the mask.
The SCSI ID you set in the mask will no
longer be a target.rw INTEGER .1.3.6.1.4.1.2512.1.1.5.1.4 |
fctoSCSIMapTableA Table containing the Fibre Channel to SCSI Map. SEQUENCE OF FCtoSCSIMapEntry .1.3.6.1.4.1.2512.1.1.6 |
fctoSCSIMapEntryAn entry in the Fibre Channel to SCSI Map Table. FCtoSCSIMapEntry .1.3.6.1.4.1.2512.1.1.6.1 |
fctoSCSIMapIndexIndex into the Fibre Channel to SCSI Map (FC LUN).ro INTEGER .1.3.6.1.4.1.2512.1.1.6.1.1 |
fctoSCSIbusSCSI bus number.rw INTEGER .1.3.6.1.4.1.2512.1.1.6.1.2 |
fctoSCSItargetSCSI ID.rw INTEGER .1.3.6.1.4.1.2512.1.1.6.1.3 |
fctoSCSILUNSCSI LUN.rw INTEGER .1.3.6.1.4.1.2512.1.1.6.1.4 |
scsitoFCMappingTableA Table containing information
describing how SCSI channels
are mapped to the Fibre Channel. SEQUENCE OF SCSItoFCMappingEntry .1.3.6.1.4.1.2512.1.1.7 |
scsitoFCMapEntryAn entry in the SCSI to FC Mapping Table. SCSItoFCMappingEntry .1.3.6.1.4.1.2512.1.1.7.1 |
scsitoFCMapIndexBusIndex into the SCSItoFC Map. SCSI bus number.ro INTEGER .1.3.6.1.4.1.2512.1.1.7.1.1 |
scsitoFCMapIndexSCSIIDIndex into the SCSItoFC Map. SCSI ID.ro INTEGER .1.3.6.1.4.1.2512.1.1.7.1.2 |
scsitoFCMapIndexLUNIndex into the SCSItoFC Map. SCSI LUN.ro INTEGER .1.3.6.1.4.1.2512.1.1.7.1.3 |
scsitoFCMapDestIDThe Fibre Channel Node number
for the destination.rw INTEGER .1.3.6.1.4.1.2512.1.1.7.1.4 |
scsitoFCMapLUNloSCSI LUN low bytes.rw Integer32 .1.3.6.1.4.1.2512.1.1.7.1.5 |
scsitoFCMapLUNhiSCSI LUN high bytes.rw Integer32 .1.3.6.1.4.1.2512.1.1.7.1.6 |
fcNPortPhysTableA Table containing N_Port
physical characteristics and status. SEQUENCE OF FcNPortPhysEntry .1.3.6.1.4.1.2512.1.1.8 |
fcNPortPhysEntryAn entry in the N_Port
Physical Characteristics Table. FcNPortPhysEntry .1.3.6.1.4.1.2512.1.1.8.1 |
fcNPortPhysNPortIndexA unique number that identifies
an N_Port/NL_Port. This number
ranges from 1 to the value
of fcNodeNumNPorts and its value
remains constant for the identified
N_Port/NL_Port until the management
agent of the Node is re-initialized.ro INTEGER .1.3.6.1.4.1.2512.1.1.8.1.1 |
fcNPortSpeedThe transmission rate,
an FC-0 physical characteristic.ro FC0Speed .1.3.6.1.4.1.2512.1.1.8.1.2 |
fcNPortMediaType of media, an FC-0 physical characteristics.ro FC0Media .1.3.6.1.4.1.2512.1.1.8.1.3 |
fcNPortTransmitterTypeType of transmitter,
an FC-0 physical characteristics.ro FC0TransmitterType .1.3.6.1.4.1.2512.1.1.8.1.4 |
fcNPortDistanceThe maximum distance,
an FC-0 physical characteristics.ro FC0Distance .1.3.6.1.4.1.2512.1.1.8.1.5 |
fcNPortLinkStateThe state of the FC link.
Pending indicates that the initialization
is still pending. Failed indicates that
link initialization has failed.
Successful indicates that the FC Link has
initialized successfully.ro Enumeration .1.3.6.1.4.1.2512.1.1.8.1.6 |
fcNPortRTTOVReceiver_Transmitter timeout value,
used by the receiver logic to detect
Loss of Synchronization.ro ReceiverTransmitterTimeoutValue .1.3.6.1.4.1.2512.1.1.8.1.7 |
fcNPortTopologyModelThe topology model on the Link.
The N_Port/NL_Port may be attached
to a Fabric, or attached to another
N_Port or to FC-AL (Arbitrated Loop).
This value is only meaningful if the FC
Link has initialized successfully.
(i.e. fcNportLinkState = Successful)ro TopologyModel .1.3.6.1.4.1.2512.1.1.8.1.8 |
scsiStatisticsTableA Table containing SCSI Statistics. SEQUENCE OF SCSIStatisticsEntry .1.3.6.1.4.1.2512.1.1.9 |
scsiStatsEntryAn entry in the SCSI Statistics Table. SCSIStatisticsEntry .1.3.6.1.4.1.2512.1.1.9.1 |
scsiStatsIndexIndex into the SCSI Statistics Table.
The SCSI bus number.ro INTEGER .1.3.6.1.4.1.2512.1.1.9.1.1 |
scsiStatsIOsThe number of IOs on the SCSI bus.ro Counter .1.3.6.1.4.1.2512.1.1.9.1.2 |
scsiStatsDisconnectsThe number of Disconnects on the SCSI bus.ro Counter .1.3.6.1.4.1.2512.1.1.9.1.3 |
scsiStatsAbortCountThe of SCSI bus termination messages
(i.e. ABORT, ABORT TAG, CLEAR QUEUE,
BUS DEVICE RESET) which have terminated
I/O processes.ro Counter .1.3.6.1.4.1.2512.1.1.9.1.4 |
scsiStatsBusResetsThe count of SCSI bus resets.ro Counter .1.3.6.1.4.1.2512.1.1.9.1.5 |
scsiCfg OBJECT IDENTIFIER .1.3.6.1.4.1.2512.1.1.10 |
scsiCfgResetFlagToggle SCSI Reset Operation. TRUE indicates
that the SCSI bus will be reset on boot.rw Boolean .1.3.6.1.4.1.2512.1.1.10.1 |
scsiCfgDiscDelayInitial Discovery Delay.
The amount of time (in msec) the system will
wait before beginning the SCSI Discovery process.rw INTEGER .1.3.6.1.4.1.2512.1.1.10.2 |
scsiProductDataTableA Table containing SCSI Product Data. SEQUENCE OF SCSIPDEntry .1.3.6.1.4.1.2512.1.1.11 |
scsiPDEntryAn entry in the SCSI Product Data Table. SCSIPDEntry .1.3.6.1.4.1.2512.1.1.11.1 |
scsiPDIndexIndex into the SCSI Product Data Table.
The SCSI LUN.ro INTEGER .1.3.6.1.4.1.2512.1.1.11.1.1 |
scsiPDBusSCSI Bus number.
Always 0 if your unit only has one SCSI Bus.ro INTEGER .1.3.6.1.4.1.2512.1.1.11.1.2 |
scsiPDTargetSCSI Target ID.ro INTEGER .1.3.6.1.4.1.2512.1.1.11.1.3 |
scsiPDLunSCSI Target Lun.ro INTEGER .1.3.6.1.4.1.2512.1.1.11.1.4 |
scsiPDVendorIDVendor ID.ro OCTET STRING .1.3.6.1.4.1.2512.1.1.11.1.5 |
scsiPDProductIDProduct ID.ro OCTET STRING .1.3.6.1.4.1.2512.1.1.11.1.6 |
scsiPDRevLevelRevision Level.ro OCTET STRING .1.3.6.1.4.1.2512.1.1.11.1.7 |
scsiPDDeviceCodeDevice type code.ro INTEGER .1.3.6.1.4.1.2512.1.1.11.1.8 |
scsiPDQualifierDevice type qualifier.ro INTEGER .1.3.6.1.4.1.2512.1.1.11.1.9 |
scsiPDRemoveableMediaRemoveable Media.ro Boolean .1.3.6.1.4.1.2512.1.1.11.1.10 |
scsiPDANSIVersionDevice type version.ro INTEGER .1.3.6.1.4.1.2512.1.1.11.1.11 |
scsiPDECMAVersionDevice type version.ro INTEGER .1.3.6.1.4.1.2512.1.1.11.1.12 |
scsiPDISOVersionDevice type version.ro INTEGER .1.3.6.1.4.1.2512.1.1.11.1.13 |
scsiPDRespFormatResponse Format.ro INTEGER .1.3.6.1.4.1.2512.1.1.11.1.14 |
scsiPDLengthAdditional data length.ro INTEGER .1.3.6.1.4.1.2512.1.1.11.1.15 |
scsiPDSoftResetSupport for Soft reset.ro Boolean .1.3.6.1.4.1.2512.1.1.11.1.16 |
scsiPDCommandQingSupport for Command Queuing.ro Boolean .1.3.6.1.4.1.2512.1.1.11.1.17 |
scsiPDLinkedCommandsSupport for Linked Commands.ro Boolean .1.3.6.1.4.1.2512.1.1.11.1.18 |
scsiPDSyncTransferSupport for Sync transfer.ro Boolean .1.3.6.1.4.1.2512.1.1.11.1.19 |
scsiPD16Bit16 bit wide SCSI support.ro Boolean .1.3.6.1.4.1.2512.1.1.11.1.20 |
scsiPD32Bit32 bit wide SCSI support.ro Boolean .1.3.6.1.4.1.2512.1.1.11.1.21 |
scsiPDRelativeAddrSupport for Relative address.ro Boolean .1.3.6.1.4.1.2512.1.1.11.1.22 |
fcNPortStatisticsTableA table of NPort statistics. SEQUENCE OF FcNPSEntry .1.3.6.1.4.1.2512.1.1.12 |
fcNPSEntryAn entry in the NPort statistics table. FcNPSEntry .1.3.6.1.4.1.2512.1.1.12.1 |
fcNPSIndexA unique number that identifies
an N_Port. This number
ranges from 1 to the value
of fcNodeNumNPorts and
its value remains constant
for the identified N_Port
until the management agent
of the Node is re-initialized.ro INTEGER .1.3.6.1.4.1.2512.1.1.12.1.1 |
fcNPSInDeviceDataSeqsThe number of Device Data sequences
received by this N_Port/NL_Port.ro Counter .1.3.6.1.4.1.2512.1.1.12.1.2 |
fcNPSOutDeviceDataSeqsThe number of Device Data sequences
transmitted by this N_Port/NL_Port.ro Counter .1.3.6.1.4.1.2512.1.1.12.1.3 |
fcNPSInLinkDataSeqsThe number of Link Data sequences
received by this N_Port/NL_Port.ro Counter .1.3.6.1.4.1.2512.1.1.12.1.4 |
fcNPSOutLinkDataSeqsThe number of Link Data sequences
transmitted by this N_Port/NL_Port.ro Counter .1.3.6.1.4.1.2512.1.1.12.1.5 |
fcNPSInPBSYFramesThe number of P_BSY frames received
by this N_Port/NL_Port.ro Counter .1.3.6.1.4.1.2512.1.1.12.1.6 |
fcNPSOutPBSYFramesThe number of P_BSY frames transmitted
by this N_Port/NL_Port.ro Counter .1.3.6.1.4.1.2512.1.1.12.1.7 |
fcNPSInFBSYFramesThe number of F_BSY frames received
by this N_Port/NL_Port.ro Counter .1.3.6.1.4.1.2512.1.1.12.1.8 |
fcNPSInPRJTFramesThe number of P_RJT frames
received by this N_Port/NL_Port.ro Counter .1.3.6.1.4.1.2512.1.1.12.1.9 |
fcNPSOutPRJTFramesThe number of P_RJT frames
transmitted by this N_Port.ro Counter .1.3.6.1.4.1.2512.1.1.12.1.10 |
fcNPSLinkDownNumber of Link down conditions detected.ro Counter .1.3.6.1.4.1.2512.1.1.12.1.11 |
fcNPSInAbortsNumber of ABTS frames received.ro Counter .1.3.6.1.4.1.2512.1.1.12.1.12 |
fcNPSOutAbortsNumber of ABTS frames sent.ro Counter .1.3.6.1.4.1.2512.1.1.12.1.13 |
fcNPSLaserFaultsNumber of laser faults.ro Counter .1.3.6.1.4.1.2512.1.1.12.1.14 |
fcNPSLOSNumber of times Loss of Signal
was detected.ro Counter .1.3.6.1.4.1.2512.1.1.12.1.15 |
fcNPSSyncNumber of times Loss of Sync.
was detected.ro Counter .1.3.6.1.4.1.2512.1.1.12.1.16 |
fcNPSBadRXCharsNumber of bad characters received.ro Counter .1.3.6.1.4.1.2512.1.1.12.1.17 |
fcNPSLinkFailNumber of Link Failure conditions.ro Counter .1.3.6.1.4.1.2512.1.1.12.1.18 |
fcNPSBadCRCNumber of frames received with a bad CRC.ro Counter .1.3.6.1.4.1.2512.1.1.12.1.19 |
fcNPSProtoErrorsNumber of protocol errors detected.ro Counter .1.3.6.1.4.1.2512.1.1.12.1.20 |