XEDIA-IPBACKUP-MIB
The XEDIA-IPBACKUP-MIB provides vendor-specific management objects for monitoring and controlling IP failover states on Xedia hardware, extending standard VRRP capabilities to track proprietary backup session parameters and redundancy status.
Imported Objects
Objects
13 total| Object Name |
|---|
xediaIpBackupMIBThis module defines additional objects for management of IP
Backup in Xedia devices, above and beyond what is defined in the
for the VRRP (or other implemented backup procedures). MODULE-IDENTITY .1.3.6.1.4.1.838.3.15 |
xipbackupObjects OBJECT IDENTIFIER .1.3.6.1.4.1.838.3.15.1 |
xipbackupGeneral OBJECT IDENTIFIER .1.3.6.1.4.1.838.3.15.1.1 |
xipbackupAdminStatusThe administrative status of IP Backup for the IP router. It is the
desired state of IP Backup for the router. The value 'enabled(1)'
indicates that the IP Backup process should be active in the router,
while 'disabled(2)' indicates that IP Backup should not be active for
the router.rw Enumeration .1.3.6.1.4.1.838.3.15.1.1.1 |
xipbackupBridgeAdminStatusThe administrative status of IP Backup for the bridge. It is the
desired state of IP Backup for the bridge. The value 'enabled(1)'
indicates that the IP Backup process should be active in the router,
while 'disabled(2)' indicates that IP Backup should not be active for
the bridge. The bridge will not forward frames if this value is
enabled unless it has achieved the master state through the IP Backup
protocol.rw Enumeration .1.3.6.1.4.1.838.3.15.1.1.2 |
xipbackupInstTableThe information associated with a backup instance. This
typically augments the vrrpOperTable. SEQUENCE OF XipbackupInstEntry .1.3.6.1.4.1.838.3.15.1.2 |
xipbackupInstEntryAn entry in the table, containing the operational
characteristics of a backup instance. A given
backup instance is identifed by a combination
of the IF index and instance ID. This table typically
augments the VRRP vrrpOperTable where vrid = instance ID. XipbackupInstEntry .1.3.6.1.4.1.838.3.15.1.2.1 |
xipbackupInstIdThis object contains the backup instance identifier. BackupId .1.3.6.1.4.1.838.3.15.1.2.1.1 |
xipbackupInstTrackIpAn IP address to be 'tracked' by this backup instance.
If this value is set, a backup instance (virtual router)
cannot become Master if this interface is not up.rw IpAddress .1.3.6.1.4.1.838.3.15.1.2.1.2 |
xipbackupInstInitializeCodeThe reason, if any, that this virtual router has not
progressed past the Initialize state. If multiple reasons,
are present, only one value is shown and correcting
that condition or configuration will reveal the
remaining reason(s). If the virtual router may enter the
Master or Backup state, the value shown is 'ready'.ro Enumeration .1.3.6.1.4.1.838.3.15.1.2.1.3 |
xipbackupConformance OBJECT IDENTIFIER .1.3.6.1.4.1.838.3.15.2 |
xipbackupCompliances OBJECT IDENTIFIER .1.3.6.1.4.1.838.3.15.2.1 |
xipbackupGroups OBJECT IDENTIFIER .1.3.6.1.4.1.838.3.15.2.2 |
More MIBs from Xedia
Browse all XediaMIBs →The XEDIA-SYSTEM-MIB provides SNMP objects to monitor and manage system-level parameters, including hardware status, resource utilization, and operational state, specifically for Xedia embedded networking devices.
The XEDIA-NETWORK-ADDRESS-TRANSLATOR-MIB provides management objects for monitoring and configuring Xedia's proprietary Network Address Translator (NAT) devices, enabling the tracking of translation sessions, address pool utilization, and packet flow statistics between RFC1918 private networks and the public Internet.
The XEDIA-POLICY-MIB enables SNMP-based configuration and monitoring of routing policy definitions, including match conditions, action sets, and policy application states, specifically within Xedia networking hardware. This module provides granular visibility into the operational status and parameter values of traffic steering rules to facilitate automated policy enforcement and troubleshooting.
The XEDIA-IPSEC-MIB enables monitoring and configuration of Xedia IPsec VPN tunnel states, security associations, and cryptographic parameters on Xedia networking hardware. It provides specific objects for tracking tunnel establishment status, packet counters, and IPsec policy enforcement metrics to ensure secure data transmission integrity.
The XEDIA-IP-MIB extends standard IETF IP-MIB functionality to monitor and manage IP-layer parameters, interfaces, and routing statistics specifically within Xedia hardware platforms. This module provides vendor-specific object identifiers for tracking IP traffic counters, interface states, and protocol configurations on Xedia network devices.
The XEDIA-NETWORK-TIME-PROTOCOL-MIB enables monitoring of Xedia's RFC 1305-compliant Network Time Protocol (NTP) implementation to manage UTC synchronization states, server association parameters, and time offset metrics across network hosts.