WEBMON-EDGE-MATRIX-MIB
AI MIB Summary
The WEBMON-EDGE-MATRIX-MIB facilitates SNMP-based monitoring of WebMon Edge-Matrix hardware, specifically exposing performance counters and status indicators for edge traffic processing, session states, and matrix topology health. This module enables the collection of critical metrics such as throughput rates, packet drop statistics, and interface utilization to support capacity planning and fault isolation in distributed edge computing environments.
WebMon Edge-Matrix MIB.
Main OID:
moduleIdentity.1.3.6.1.4.1.994.3.4.3
878
Objects
Active
Status
3
Dependencies
Imported Objects
Objects
878 total| Object Name |
|---|
dantel OBJECT IDENTIFIER .1.3.6.1.4.1.994 |
dantelProducts OBJECT IDENTIFIER .1.3.6.1.4.1.994.3 |
webMonThe parent node representing the WebMon device. OBJECT IDENTIFIER .1.3.6.1.4.1.994.3.4 |
moduleIdentityWebMon Edge-Matrix MIB. MODULE-IDENTITY .1.3.6.1.4.1.994.3.4.3 |
notificationGroupGroup containing all the notification types. Unknown .1.3.6.1.4.1.994.3.4.4 |
objectGroupGroup containing all the objects. Unknown .1.3.6.1.4.1.994.3.4.5 |
trapsCategory containing all the traps. Each trap has sibling data nodes that contain the data associated with the most recently sent trap of that particular type. A GET-REQUEST sent to the WebMon for those data nodes will allow you to verify the data received in a recent trap. OBJECT IDENTIFIER .1.3.6.1.4.1.994.3.4.6 |
analogInputsSubtree containing trap and associated data for analog inputs. Analog inputs measure a value. The input always has a live reading, but traps are only sent on events, which are defined as the live reading crossing (or passing) one of the user-defined thresholds. OBJECT IDENTIFIER .1.3.6.1.4.1.994.3.4.6.1 |
analogEventTrapNotification sent upon an analog input reading crossing a threshold. NOTIFICATION-TYPE .1.3.6.1.4.1.994.3.4.6.1.1 |
analogInputDescriptionDescription of the analog input.ro DescriptionString .1.3.6.1.4.1.994.3.4.6.1.2 |
analogLiveLevelThe level associated with the analogLiveReading for this input.ro Level .1.3.6.1.4.1.994.3.4.6.1.3 |
analogLiveReadingThe reading from the analog input described by analogInputDescription at the time the trap was sent. It is in the units described in analogUnitsOfMeasurement.ro DescriptionString .1.3.6.1.4.1.994.3.4.6.1.5 |
analogUnitsOfMeasurementThe units of measurement associated with the analogLiveReading.ro DescriptionString .1.3.6.1.4.1.994.3.4.6.1.6 |
analogLiveStateThe state associated with analogLiveReading.ro AnalogState .1.3.6.1.4.1.994.3.4.6.1.7 |
analogLiveStateDescriptionThe description of the range in which the analogLiveReading is.ro DescriptionString .1.3.6.1.4.1.994.3.4.6.1.8 |
analogAlarmStateIf true this field indicates the alarmed state. If false this field indicates the not alarmed state.ro Boolean .1.3.6.1.4.1.994.3.4.6.1.9 |
analogSourceDescriptionDescription of the event source. DescriptionString .1.3.6.1.4.1.994.3.4.6.1.101 |
analogSourceIndexIndex of the event source. Integer32 .1.3.6.1.4.1.994.3.4.6.1.102 |
digitalInputsSubtree containing trap and associated data for digital inputs. Digital inputs monitor a binary state. The input is always in one of two states. Traps are sent on events, which are defined as a change in the live state. OBJECT IDENTIFIER .1.3.6.1.4.1.994.3.4.6.2 |
digitalEventTrapNotification sent upon change of state on a digital input. NOTIFICATION-TYPE .1.3.6.1.4.1.994.3.4.6.2.1 |
digitalInputDescriptionDescription of the digital input.ro DescriptionString .1.3.6.1.4.1.994.3.4.6.2.2 |
digitalLiveLevelThe level associated with digitalLiveState for this input.ro Level .1.3.6.1.4.1.994.3.4.6.2.3 |
digitalLiveStateThe state of the digital input described by digitalInputDescription at the time the trap was sent.ro DigitalState .1.3.6.1.4.1.994.3.4.6.2.4 |
digitalLiveStateDescriptionThe description of the digitalLiveState.ro DescriptionString .1.3.6.1.4.1.994.3.4.6.2.5 |
digitalAlarmStateIf true this field indicates the alarmed state. If false this field indicates the not alarmed state.ro Boolean .1.3.6.1.4.1.994.3.4.6.2.6 |
digitalSourceDescriptionDescription of the event source. DescriptionString .1.3.6.1.4.1.994.3.4.6.2.101 |
digitalSourceIndexIndex of the event source. Integer32 .1.3.6.1.4.1.994.3.4.6.2.102 |
remoteDevicesSubtree containing trap and associated data for monitored remote devices. Remote devices are monitored for network connectivity. The device's live state is always either online or offline. Traps are sent on events, which are defined as a change in the live state. OBJECT IDENTIFIER .1.3.6.1.4.1.994.3.4.6.3 |
remoteDeviceEventTrapNotification sent upon change of state of a remote device. NOTIFICATION-TYPE .1.3.6.1.4.1.994.3.4.6.3.1 |
remoteDeviceDescriptionDescription of the remote device.ro DescriptionString .1.3.6.1.4.1.994.3.4.6.3.2 |
remoteDeviceLiveLevelThe level associated with remoteDeviceLiveState.ro Level .1.3.6.1.4.1.994.3.4.6.3.3 |
remoteDeviceLiveStateThe state of the remote device described by remoteDeviceDescription at the time the trap was sent. Online indicates connected, offline indicates not connected.ro ConnectivityState .1.3.6.1.4.1.994.3.4.6.3.4 |
remoteDeviceAlarmStateIf true this field indicates the alarmed state. If false this field indicates the not alarmed state.ro Boolean .1.3.6.1.4.1.994.3.4.6.3.5 |
remoteDeviceSourceDescriptionDescription of the event source. DescriptionString .1.3.6.1.4.1.994.3.4.6.3.101 |
remoteDeviceSourceIndexIndex of the event source. Integer32 .1.3.6.1.4.1.994.3.4.6.3.102 |
faultsSubtree containing trap and associated data for faults. Faults are conditions internal to the WebMon. The only data associated with this trap is a string that describes the condition. OBJECT IDENTIFIER .1.3.6.1.4.1.994.3.4.6.4 |
faultTrapNotification sent when a fault is encountered. NOTIFICATION-TYPE .1.3.6.1.4.1.994.3.4.6.4.1 |
faultDescriptionDescription of the condition at the WebMon.ro DescriptionString .1.3.6.1.4.1.994.3.4.6.4.2 |
faultLiveLevelThe level associated with faultStateDescription.ro Level .1.3.6.1.4.1.994.3.4.6.4.3 |
faultStateDescriptionThe description of the state of this fault.ro DescriptionString .1.3.6.1.4.1.994.3.4.6.4.4 |
faultAlarmStateIf true this field indicates the alarmed state. If false this field indicates the not alarmed state.ro Boolean .1.3.6.1.4.1.994.3.4.6.4.5 |
faultSourceDescriptionDescription of the event source. DescriptionString .1.3.6.1.4.1.994.3.4.6.4.101 |
faultSourceIndexIndex of the event source. Integer32 .1.3.6.1.4.1.994.3.4.6.4.102 |
configuration OBJECT IDENTIFIER .1.3.6.1.4.1.994.3.4.7 |
systemGeneral OBJECT IDENTIFIER .1.3.6.1.4.1.994.3.4.7.1 |
systemGeneralLocationLocation on the device.rw DescriptionString .1.3.6.1.4.1.994.3.4.7.1.2 |
systemGeneralDescriptionDescription of the device.rw DescriptionString .1.3.6.1.4.1.994.3.4.7.1.3 |
systemGeneralIpAddressIP Address of the device. If changed, the new IP address will only take effect after a reset.rw IpAddress .1.3.6.1.4.1.994.3.4.7.1.14 |
systemGeneralSubnetMaskSubnet Mask of the device. If changed, the new IP address will only take effect after a reset.rw IpAddress .1.3.6.1.4.1.994.3.4.7.1.15 |
systemGeneralGatewayAddressGateway Address of the device. If changed, the new IP address will only take effect after a reset.rw IpAddress .1.3.6.1.4.1.994.3.4.7.1.16 |
systemGeneralMeasureStyleDetermines if units are displayed in English or Metric.rw MeasureStyle .1.3.6.1.4.1.994.3.4.7.1.45 |
systemGeneralMacAddressThe MAC address of the device.ro DescriptionString .1.3.6.1.4.1.994.3.4.7.1.54 |
systemGeneralProductTypeDescribes the type of device.ro ProductType .1.3.6.1.4.1.994.3.4.7.1.70 |
systemGeneralIPPortNumIP port number to use when connecting to the web page (HTTP).rw Integer32 .1.3.6.1.4.1.994.3.4.7.1.73 |
systemGeneralVersionThe version of the running software.ro DescriptionString .1.3.6.1.4.1.994.3.4.7.1.82 |
pTrapTargetTableTable for configuration of TrapTarget SEQUENCE OF PTrapTargetEntry .1.3.6.1.4.1.994.3.4.7.2 |
pTrapTargetEntryEntry for configuration table of TrapTarget PTrapTargetEntry .1.3.6.1.4.1.994.3.4.7.2.1 |
pTrapTargetDescriptionDescription of the trap target.rw DescriptionString .1.3.6.1.4.1.994.3.4.7.2.1.3 |
pTrapTargetConfiguredDetermines if traps will be sent to trap target with given IP address.rw Configured .1.3.6.1.4.1.994.3.4.7.2.1.10 |
pTrapTargetIpAddressSNMP traps are sent to this IP address.rw IpAddress .1.3.6.1.4.1.994.3.4.7.2.1.14 |
pTrapTargetSnmpVersionIndicates the version of SNMP trap to use.rw SnmpVersion .1.3.6.1.4.1.994.3.4.7.2.1.42 |
pTrapTargetIPPortNumSNMP traps are sent to this network port.rw Integer32 .1.3.6.1.4.1.994.3.4.7.2.1.73 |
pTrapTargetBackupIPAddressUsed only when dialing out as backup.rw IpAddress .1.3.6.1.4.1.994.3.4.7.2.1.78 |
pTrapTargetUseDialoutDetermines if traps will be sent only when dialed out.rw UseDialout .1.3.6.1.4.1.994.3.4.7.2.1.125 |
pTrapTargetDialoutTargetDetermines which target to dial out to when sending traps.rw Integer32 .1.3.6.1.4.1.994.3.4.7.2.1.126 |
pTrapTargetAuthKeyrw DescriptionString .1.3.6.1.4.1.994.3.4.7.2.1.140 |
pTrapTargetPrivKeyrw DescriptionString .1.3.6.1.4.1.994.3.4.7.2.1.141 |
pTrapTargetSNMPAccessrw SNMPAccess .1.3.6.1.4.1.994.3.4.7.2.1.142 |
pTrapTargetEngineIDrw DescriptionString .1.3.6.1.4.1.994.3.4.7.2.1.143 |
pTrapTargetIndexIndex.ro Integer32 .1.3.6.1.4.1.994.3.4.7.2.1.999 |
pEmailTableTable for configuration of Email SEQUENCE OF PEmailEntry .1.3.6.1.4.1.994.3.4.7.3 |
pEmailEntryEntry for configuration table of Email PEmailEntry .1.3.6.1.4.1.994.3.4.7.3.1 |
pEmailAddressEmail events will be sent to this address.rw DescriptionString .1.3.6.1.4.1.994.3.4.7.3.1.1 |
pEmailDescriptionDescription of the Email target.rw DescriptionString .1.3.6.1.4.1.994.3.4.7.3.1.3 |
pEmailConfiguredIf set to true, email events will be sent to given address. If set to false, email will not be sent.rw Configured .1.3.6.1.4.1.994.3.4.7.3.1.10 |
pEmailIndexIndex.ro Integer32 .1.3.6.1.4.1.994.3.4.7.3.1.999 |
pRemoteSensorTableTable for configuration of RemoteSensor SEQUENCE OF PRemoteSensorEntry .1.3.6.1.4.1.994.3.4.7.5 |
pRemoteSensorEntryEntry for configuration table of RemoteSensor PRemoteSensorEntry .1.3.6.1.4.1.994.3.4.7.5.1 |
pRemoteSensorDescriptionDescription of the Analog device.rw DescriptionString .1.3.6.1.4.1.994.3.4.7.5.1.3 |
pRemoteSensorDesc0The description for values between threshold 0 and threshold 1.rw DescriptionString .1.3.6.1.4.1.994.3.4.7.5.1.4 |
pRemoteSensorDesc1The description for values between threshold 1 and threshold 2.rw DescriptionString .1.3.6.1.4.1.994.3.4.7.5.1.5 |
pRemoteSensorDesc2The description for values between threshold 2 and threshold 3.rw DescriptionString .1.3.6.1.4.1.994.3.4.7.5.1.6 |
pRemoteSensorDesc3The description for values between threshold 3 and threshold 4.rw DescriptionString .1.3.6.1.4.1.994.3.4.7.5.1.7 |
pRemoteSensorDesc4The description for values between threshold 4 and threshold 5.rw DescriptionString .1.3.6.1.4.1.994.3.4.7.5.1.8 |
pRemoteSensorDesc5Description for a communications failure to the remote analog device.rw DescriptionString .1.3.6.1.4.1.994.3.4.7.5.1.9 |
pRemoteSensorConfiguredIf set to true analog values will be monitored. If set to false no values will be monitored.rw Configured .1.3.6.1.4.1.994.3.4.7.5.1.10 |
pRemoteSensorSendEmailIf set to true an email event will be set when a threshold is crossed. If set to false no email event will be sent.rw Boolean .1.3.6.1.4.1.994.3.4.7.5.1.11 |
pRemoteSensorSendSNMPTrapIf set to true an SNMP trap will be set when a threshold is crossed. If set to false no SNMP trap will be sent.rw Boolean .1.3.6.1.4.1.994.3.4.7.5.1.12 |
pRemoteSensorLevel0The level for values between threshold 0 and threshold 1.rw Level .1.3.6.1.4.1.994.3.4.7.5.1.17 |
pRemoteSensorLevel1The level for values between threshold 1 and threshold 2.rw Level .1.3.6.1.4.1.994.3.4.7.5.1.18 |
pRemoteSensorLevel2The level for values between threshold 2 and threshold 3.rw Level .1.3.6.1.4.1.994.3.4.7.5.1.19 |
pRemoteSensorLevel3The level for values between threshold 3 and threshold 4.rw Level .1.3.6.1.4.1.994.3.4.7.5.1.20 |
pRemoteSensorLevel4The level for values between threshold 4 and threshold 5.rw Level .1.3.6.1.4.1.994.3.4.7.5.1.21 |
pRemoteSensorLevel5Level of a communications failure to the remote analog device.rw Level .1.3.6.1.4.1.994.3.4.7.5.1.22 |
pRemoteSensorThresh0This is the maximum analog value.rw DescriptionString .1.3.6.1.4.1.994.3.4.7.5.1.28 |
pRemoteSensorThresh1This is the first threshold value.rw DescriptionString .1.3.6.1.4.1.994.3.4.7.5.1.29 |
pRemoteSensorThresh2This is the second threshold value.rw DescriptionString .1.3.6.1.4.1.994.3.4.7.5.1.30 |
pRemoteSensorThresh3This is the third threshold value.rw DescriptionString .1.3.6.1.4.1.994.3.4.7.5.1.31 |
pRemoteSensorThresh4This is the fourth threshold value.rw DescriptionString .1.3.6.1.4.1.994.3.4.7.5.1.32 |
pRemoteSensorThresh5This is the minimum threshold value.rw DescriptionString .1.3.6.1.4.1.994.3.4.7.5.1.33 |
pRemoteSensorUnitsDescription of the units of measurement.rw DescriptionString .1.3.6.1.4.1.994.3.4.7.5.1.46 |
pRemoteSensorPollAddressThe polling address of the analog device.rw Integer32 .1.3.6.1.4.1.994.3.4.7.5.1.56 |
pRemoteSensorLiveDescriptionThe description of the current state of the analog devicero DescriptionString .1.3.6.1.4.1.994.3.4.7.5.1.64 |
pRemoteSensorLiveLevelThe level of the current state of the analog device.ro DescriptionString .1.3.6.1.4.1.994.3.4.7.5.1.65 |
pRemoteSensorLiveRawThe current reading from the analog device. This value will always be between the threshold 0 and threshold 5 values.ro DescriptionString .1.3.6.1.4.1.994.3.4.7.5.1.66 |
pRemoteSensorLiveTimeThe time of the last event.ro DescriptionString .1.3.6.1.4.1.994.3.4.7.5.1.67 |
pRemoteSensorTL1SID(TL1) System ID associated with this item.rw DescriptionString .1.3.6.1.4.1.994.3.4.7.5.1.116 |
pRemoteSensorTL1COND(TL1) Condition text associated with this item.rw DescriptionString .1.3.6.1.4.1.994.3.4.7.5.1.117 |
pRemoteSensorTL1Eqpt(TL1) EQPT field associated with this item.rw DescriptionString .1.3.6.1.4.1.994.3.4.7.5.1.118 |
pRemoteSensorTL1Env(TL1) Environmental field associated with this item.rw Boolean .1.3.6.1.4.1.994.3.4.7.5.1.119 |
pRemoteSensorTL1Srveff(TL1) Service Effecting field associated with this item.rw TL1Srveff .1.3.6.1.4.1.994.3.4.7.5.1.120 |
pRemoteSensorTL1Locn(TL1) Location field associated with this item.rw TL1Locn .1.3.6.1.4.1.994.3.4.7.5.1.121 |
pRemoteSensorTL1Dirn(TL1) Direction field associated with this item.rw TL1Dirn .1.3.6.1.4.1.994.3.4.7.5.1.122 |
pRemoteSensorMODBUSCommandThe polling command for the analog device.rw MODBUSCommand .1.3.6.1.4.1.994.3.4.7.5.1.144 |
pRemoteSensorStartRegisterThe MODBUS register for the analog device.rw Integer32 .1.3.6.1.4.1.994.3.4.7.5.1.145 |
pRemoteSensorIndexIndex.ro Integer32 .1.3.6.1.4.1.994.3.4.7.5.1.999 |
pOnboardSensorTableTable for configuration of OnboardSensor SEQUENCE OF POnboardSensorEntry .1.3.6.1.4.1.994.3.4.7.6 |
pOnboardSensorEntryEntry for configuration table of OnboardSensor POnboardSensorEntry .1.3.6.1.4.1.994.3.4.7.6.1 |
pOnboardSensorDescriptionDescription of the onboard sensor input.ro DescriptionString .1.3.6.1.4.1.994.3.4.7.6.1.3 |
pOnboardSensorDesc0The description for values between threshold 0 and threshold 1.rw DescriptionString .1.3.6.1.4.1.994.3.4.7.6.1.4 |
pOnboardSensorDesc1The description for values between threshold 1 and threshold 2.rw DescriptionString .1.3.6.1.4.1.994.3.4.7.6.1.5 |
pOnboardSensorDesc2The description for values between threshold 2 and threshold 3.rw DescriptionString .1.3.6.1.4.1.994.3.4.7.6.1.6 |
pOnboardSensorDesc3The description for values between threshold 3 and threshold 4.rw DescriptionString .1.3.6.1.4.1.994.3.4.7.6.1.7 |
pOnboardSensorDesc4The description for values between threshold 4 and threshold 5.rw DescriptionString .1.3.6.1.4.1.994.3.4.7.6.1.8 |
pOnboardSensorDesc5Description for a communications failure to the sensor.rw DescriptionString .1.3.6.1.4.1.994.3.4.7.6.1.9 |
pOnboardSensorConfiguredIf set to true, the sensor input will be usable. If set to false the sensor input will be ignored.rw Configured .1.3.6.1.4.1.994.3.4.7.6.1.10 |
pOnboardSensorSendEmailIf set to true an email event will be set when a threshold is crossed. If set to false no email event will be sent.rw Boolean .1.3.6.1.4.1.994.3.4.7.6.1.11 |
pOnboardSensorSendSNMPTrapIf set to true an SNMP trap will be set when a threshold is crossed. If set to false no SNMP trap will be sent.rw Boolean .1.3.6.1.4.1.994.3.4.7.6.1.12 |
pOnboardSensorLevel0The level for values between threshold 0 and threshold 1.rw Level .1.3.6.1.4.1.994.3.4.7.6.1.17 |
pOnboardSensorLevel1The level for values between threshold 1 and threshold 2.rw Level .1.3.6.1.4.1.994.3.4.7.6.1.18 |
pOnboardSensorLevel2The level for values between threshold 2 and threshold 3.rw Level .1.3.6.1.4.1.994.3.4.7.6.1.19 |
pOnboardSensorLevel3The level for values between threshold 3 and threshold 4.rw Level .1.3.6.1.4.1.994.3.4.7.6.1.20 |
pOnboardSensorLevel4The level for values between threshold 4 and threshold 5.rw Level .1.3.6.1.4.1.994.3.4.7.6.1.21 |
pOnboardSensorLevel5Level of a communications failure to the sensor.rw Level .1.3.6.1.4.1.994.3.4.7.6.1.22 |
pOnboardSensorThresh0This is the minimun analog value.ro DescriptionString .1.3.6.1.4.1.994.3.4.7.6.1.28 |
pOnboardSensorThresh1This is the first threshold value.rw DescriptionString .1.3.6.1.4.1.994.3.4.7.6.1.29 |
pOnboardSensorThresh2This is the second threshold value.rw DescriptionString .1.3.6.1.4.1.994.3.4.7.6.1.30 |
pOnboardSensorThresh3This is the third threshold value.rw DescriptionString .1.3.6.1.4.1.994.3.4.7.6.1.31 |
pOnboardSensorThresh4This is the fourth threshold value.rw DescriptionString .1.3.6.1.4.1.994.3.4.7.6.1.32 |
pOnboardSensorThresh5This is the maximum threshold value.ro DescriptionString .1.3.6.1.4.1.994.3.4.7.6.1.33 |
pOnboardSensorUnitsDescription of the units of measurement.ro DescriptionString .1.3.6.1.4.1.994.3.4.7.6.1.46 |
pOnboardSensorLiveDescriptionThe description of the current state of the onboard sensorro DescriptionString .1.3.6.1.4.1.994.3.4.7.6.1.64 |
pOnboardSensorLiveLevelThe level of the current state of the onboard sensor.ro DescriptionString .1.3.6.1.4.1.994.3.4.7.6.1.65 |
pOnboardSensorLiveRawThe current reading from the onboard sensor. This value will always be between the threshold 0 and threshold 5 values.ro DescriptionString .1.3.6.1.4.1.994.3.4.7.6.1.66 |
pOnboardSensorLiveTimeThe time of the last event.ro DescriptionString .1.3.6.1.4.1.994.3.4.7.6.1.67 |
pOnboardSensorTL1SID(TL1) System ID associated with this item.rw DescriptionString .1.3.6.1.4.1.994.3.4.7.6.1.116 |
pOnboardSensorTL1COND(TL1) Condition text associated with this item.rw DescriptionString .1.3.6.1.4.1.994.3.4.7.6.1.117 |
pOnboardSensorTL1Eqpt(TL1) EQPT field associated with this item.rw DescriptionString .1.3.6.1.4.1.994.3.4.7.6.1.118 |
pOnboardSensorTL1Env(TL1) Environmental field associated with this item.rw Boolean .1.3.6.1.4.1.994.3.4.7.6.1.119 |
pOnboardSensorTL1Srveff(TL1) Service Effecting field associated with this item.rw TL1Srveff .1.3.6.1.4.1.994.3.4.7.6.1.120 |
pOnboardSensorTL1Locn(TL1) Location field associated with this item.rw TL1Locn .1.3.6.1.4.1.994.3.4.7.6.1.121 |
pOnboardSensorTL1Dirn(TL1) Direction field associated with this item.rw TL1Dirn .1.3.6.1.4.1.994.3.4.7.6.1.122 |
pOnboardSensorIndexIndex.ro Integer32 .1.3.6.1.4.1.994.3.4.7.6.1.999 |
pNetDevicesTableTable for configuration of NetDevices SEQUENCE OF PNetDevicesEntry .1.3.6.1.4.1.994.3.4.7.7 |
pNetDevicesEntryEntry for configuration table of NetDevices PNetDevicesEntry .1.3.6.1.4.1.994.3.4.7.7.1 |
pNetDevicesDescriptionDescription of the network device.rw DescriptionString .1.3.6.1.4.1.994.3.4.7.7.1.3 |
pNetDevicesDesc0Text description of online state.rw DescriptionString .1.3.6.1.4.1.994.3.4.7.7.1.4 |
pNetDevicesDesc1Text description of offline state.rw DescriptionString .1.3.6.1.4.1.994.3.4.7.7.1.5 |
pNetDevicesConfiguredIf set to true, net device will be pinged, If set to false, no action will be taken.rw Configured .1.3.6.1.4.1.994.3.4.7.7.1.10 |
pNetDevicesSendEmailIf set to true, an email will be sent when a change of state is detected. If set to false, no email will be sent.rw Boolean .1.3.6.1.4.1.994.3.4.7.7.1.11 |
pNetDevicesSendSNMPTrapIf set to true, an SNMP trap will be sent when a change of state is detected. If set to false, no SNMP trap will be sent.rw Boolean .1.3.6.1.4.1.994.3.4.7.7.1.12 |
pNetDevicesIpAddressThe IP address of the net device to ping.rw IpAddress .1.3.6.1.4.1.994.3.4.7.7.1.14 |
pNetDevicesLevel0Alarm level associated with the online state.rw Level .1.3.6.1.4.1.994.3.4.7.7.1.17 |
pNetDevicesLevel1Alarm level associated with the offline state.rw Level .1.3.6.1.4.1.994.3.4.7.7.1.18 |
pNetDevicesLiveDescriptionThe description of the current state of the net devicero DescriptionString .1.3.6.1.4.1.994.3.4.7.7.1.64 |
pNetDevicesLiveLevelThe level of the current state of the net device.ro DescriptionString .1.3.6.1.4.1.994.3.4.7.7.1.65 |
pNetDevicesLiveRawThe current reading from the net device. This value will always be between the threshold 0 and threshold 5 values.ro DescriptionString .1.3.6.1.4.1.994.3.4.7.7.1.66 |
pNetDevicesLiveTimeThe time of the last event.ro DescriptionString .1.3.6.1.4.1.994.3.4.7.7.1.67 |
pNetDevicesTL1SID(TL1) System ID associated with this item.rw DescriptionString .1.3.6.1.4.1.994.3.4.7.7.1.116 |
pNetDevicesTL1COND(TL1) Condition text associated with this item.rw DescriptionString .1.3.6.1.4.1.994.3.4.7.7.1.117 |
pNetDevicesTL1Eqpt(TL1) EQPT field associated with this item.rw DescriptionString .1.3.6.1.4.1.994.3.4.7.7.1.118 |
pNetDevicesTL1Env(TL1) Environmental field associated with this item.rw Boolean .1.3.6.1.4.1.994.3.4.7.7.1.119 |
pNetDevicesTL1Srveff(TL1) Service Effecting field associated with this item.rw TL1Srveff .1.3.6.1.4.1.994.3.4.7.7.1.120 |
pNetDevicesTL1Locn(TL1) Location field associated with this item.rw TL1Locn .1.3.6.1.4.1.994.3.4.7.7.1.121 |
pNetDevicesTL1Dirn(TL1) Direction field associated with this item.rw TL1Dirn .1.3.6.1.4.1.994.3.4.7.7.1.122 |
pNetDevicesIndexIndex.ro Integer32 .1.3.6.1.4.1.994.3.4.7.7.1.999 |
pAccountsTableTable for configuration of Accounts SEQUENCE OF PAccountsEntry .1.3.6.1.4.1.994.3.4.7.9 |
pAccountsEntryEntry for configuration table of Accounts PAccountsEntry .1.3.6.1.4.1.994.3.4.7.9.1 |
pAccountsConfiguredIf set to true, this account can be used to login.rw Configured .1.3.6.1.4.1.994.3.4.7.9.1.10 |
pAccountsNameName associated with this account.rw DescriptionString .1.3.6.1.4.1.994.3.4.7.9.1.25 |
pAccountsEncPasswordPassword for this account. When reading, an encrypted version of password will be displayed. When writing, use plain text.rw DescriptionString .1.3.6.1.4.1.994.3.4.7.9.1.27 |
pAccountsUserLevelThe user level for this account. One of the following masks from each group are used: No FTP access 0x0000 0 FTP read-only 0x0001 1 FTP Full access 0x0003 3 No Web access 0x0000 0 Monitor 0x0010 16 Config 0x0030 48 Config + Accounts 0x00B0 176 The masks are added together to create a permission value.rw Unsigned32 .1.3.6.1.4.1.994.3.4.7.9.1.55 |
pAccountsUnsecuredAllow secured configuration for SNMP through this account.rw Boolean .1.3.6.1.4.1.994.3.4.7.9.1.77 |
pAccountsAuthKeyrw DescriptionString .1.3.6.1.4.1.994.3.4.7.9.1.140 |
pAccountsPrivKeyrw DescriptionString .1.3.6.1.4.1.994.3.4.7.9.1.141 |
pAccountsSNMPAccessrw SNMPAccess .1.3.6.1.4.1.994.3.4.7.9.1.142 |
pAccountsIndexIndex.ro Integer32 .1.3.6.1.4.1.994.3.4.7.9.1.999 |
camera OBJECT IDENTIFIER .1.3.6.1.4.1.994.3.4.7.10 |
cameraConfiguredIf set to true, camera view will be used in main webpage. If set to false, camera view will not be used.rw Configured .1.3.6.1.4.1.994.3.4.7.10.10 |
cameraIpAddressIP address of the camera.rw IpAddress .1.3.6.1.4.1.994.3.4.7.10.14 |
cameraCameraStyleType of camera used.rw CameraStyle .1.3.6.1.4.1.994.3.4.7.10.43 |
snmpGeneral OBJECT IDENTIFIER .1.3.6.1.4.1.994.3.4.7.12 |
snmpGeneralConfiguredResend standing alarms at a given intervalrw Configured .1.3.6.1.4.1.994.3.4.7.12.10 |
snmpGeneralReadPeriodPeriod in minutes between resend of standing alarmsrw Integer32 .1.3.6.1.4.1.994.3.4.7.12.23 |
snmpGeneralGetGet community name for SNMP.rw DescriptionString .1.3.6.1.4.1.994.3.4.7.12.39 |
snmpGeneralSetSet community name for SNMP.rw DescriptionString .1.3.6.1.4.1.994.3.4.7.12.40 |
snmpGeneralTrapTrap community name for SNMP.rw DescriptionString .1.3.6.1.4.1.994.3.4.7.12.41 |
snmpGeneralIPPortNumSNMP configuration is done on this network port.rw Integer32 .1.3.6.1.4.1.994.3.4.7.12.73 |
snmpGeneralEngineIDSNMP v3 engine IDro DescriptionString .1.3.6.1.4.1.994.3.4.7.12.143 |
emailGeneral OBJECT IDENTIFIER .1.3.6.1.4.1.994.3.4.7.13 |
emailGeneralAddressLogin name to use if logging into email server is true.rw DescriptionString .1.3.6.1.4.1.994.3.4.7.13.1 |
emailGeneralConfiguredIf set to true, the device will log onto the email server before sending and email event. If set to false, the device will not log onto email server.rw Configured .1.3.6.1.4.1.994.3.4.7.13.10 |
emailGeneralIpAddressIP address of email server.rw IpAddress .1.3.6.1.4.1.994.3.4.7.13.14 |
emailGeneralPasswordPassword to use if logging into email server is true.rw DescriptionString .1.3.6.1.4.1.994.3.4.7.13.26 |
emailGeneralIPPortNumPort number address of email server.rw Integer32 .1.3.6.1.4.1.994.3.4.7.13.73 |
pSerialTableTable for configuration of Serial SEQUENCE OF PSerialEntry .1.3.6.1.4.1.994.3.4.7.14 |
pSerialEntryEntry for configuration table of Serial PSerialEntry .1.3.6.1.4.1.994.3.4.7.14.1 |
pSerialDescriptionDescription of the serial port.ro DescriptionString .1.3.6.1.4.1.994.3.4.7.14.1.3 |
pSerialConfiguredIf set to true, this serial port will be usable. If set to false the port will not be usable.rw Configured .1.3.6.1.4.1.994.3.4.7.14.1.10 |
pSerialIpAddressIP Address of the target device.rw IpAddress .1.3.6.1.4.1.994.3.4.7.14.1.14 |
pSerialReadPeriodInactivity timeout (in minutes).rw Integer32 .1.3.6.1.4.1.994.3.4.7.14.1.23 |
pSerialBaudRateBaud rate of the serial port.rw BaudRate .1.3.6.1.4.1.994.3.4.7.14.1.57 |
pSerialDataBitsNumber of data bit for the serial port.rw DataBits .1.3.6.1.4.1.994.3.4.7.14.1.58 |
pSerialParityParity of the serial port.rw Parity .1.3.6.1.4.1.994.3.4.7.14.1.59 |
pSerialStopBitsNumber of stop bits for the serial port.rw StopBits .1.3.6.1.4.1.994.3.4.7.14.1.60 |
pSerialProtocolProtocol the serial port is speaking.rw Protocol .1.3.6.1.4.1.994.3.4.7.14.1.61 |
pSerialSerialRTSRequest To Send (RTS) setting for the serial port.rw SerialRTS .1.3.6.1.4.1.994.3.4.7.14.1.62 |
pSerialSerialCTSClear To Send (CTS) setting for the serial port.rw SerialCTS .1.3.6.1.4.1.994.3.4.7.14.1.63 |
pSerialPresentIf set to true, the serial port exists. If set to false the serial port does not exist.ro Boolean .1.3.6.1.4.1.994.3.4.7.14.1.68 |
pSerialIPPortNumIP port number of the target device.rw Integer32 .1.3.6.1.4.1.994.3.4.7.14.1.73 |
pSerialPortTypeThe type of serial port.ro PortType .1.3.6.1.4.1.994.3.4.7.14.1.76 |
pSerialIndexIndex.ro Integer32 .1.3.6.1.4.1.994.3.4.7.14.1.999 |
pSelfTestTableTable for configuration of SelfTest SEQUENCE OF PSelfTestEntry .1.3.6.1.4.1.994.3.4.7.15 |
pSelfTestEntryEntry for configuration table of SelfTest PSelfTestEntry .1.3.6.1.4.1.994.3.4.7.15.1 |
pSelfTestDescriptionDescription of the Power On Self Test (POST).rw DescriptionString .1.3.6.1.4.1.994.3.4.7.15.1.3 |
pSelfTestConfiguredIf set to true, this POST has passed. If set to false, it has failed.rw Configured .1.3.6.1.4.1.994.3.4.7.15.1.10 |
pSelfTestIndexIndex.ro Integer32 .1.3.6.1.4.1.994.3.4.7.15.1.999 |
pInternalFaultsTableTable for configuration of InternalFaults SEQUENCE OF PInternalFaultsEntry .1.3.6.1.4.1.994.3.4.7.16 |
pInternalFaultsEntryEntry for configuration table of InternalFaults PInternalFaultsEntry .1.3.6.1.4.1.994.3.4.7.16.1 |
pInternalFaultsDescriptionDescription of the internal fault.ro DescriptionString .1.3.6.1.4.1.994.3.4.7.16.1.3 |
pInternalFaultsDesc0Text description of the healthy state.ro DescriptionString .1.3.6.1.4.1.994.3.4.7.16.1.4 |
pInternalFaultsDesc1Text description of a non-normal state.ro DescriptionString .1.3.6.1.4.1.994.3.4.7.16.1.5 |
pInternalFaultsDesc2Text description of a non-normal state.ro DescriptionString .1.3.6.1.4.1.994.3.4.7.16.1.6 |
pInternalFaultsDesc3Text description of a non-normal state.ro DescriptionString .1.3.6.1.4.1.994.3.4.7.16.1.7 |
pInternalFaultsSendEmailIf set to true an email event will be set when a change occurs. If set to false no email event will be sent.rw Boolean .1.3.6.1.4.1.994.3.4.7.16.1.11 |
pInternalFaultsSendSNMPTrapIf set to true an SNMP trap will be set when a change occurs. If set to false no SNMP trap will be sent.rw Boolean .1.3.6.1.4.1.994.3.4.7.16.1.12 |
pInternalFaultsLevel0Alarm level associated with the healthy state.rw Level .1.3.6.1.4.1.994.3.4.7.16.1.17 |
pInternalFaultsLevel1Alarm level associated with this non-normal state.rw Level .1.3.6.1.4.1.994.3.4.7.16.1.18 |
pInternalFaultsLevel2Alarm level associated with this non-normal state.rw Level .1.3.6.1.4.1.994.3.4.7.16.1.19 |
pInternalFaultsLevel3Alarm level associated with this non-normal state.rw Level .1.3.6.1.4.1.994.3.4.7.16.1.20 |
pInternalFaultsIgnoreOffIf true, no event is generated for a change to the healty state.rw Boolean .1.3.6.1.4.1.994.3.4.7.16.1.50 |
pInternalFaultsLiveDescriptionThe current condition of the internal fault.ro DescriptionString .1.3.6.1.4.1.994.3.4.7.16.1.64 |
pInternalFaultsLiveLevelThe current level of the internal fault.ro DescriptionString .1.3.6.1.4.1.994.3.4.7.16.1.65 |
pInternalFaultsLiveTimeThe time of the fault event.ro DescriptionString .1.3.6.1.4.1.994.3.4.7.16.1.67 |
pInternalFaultsIndexIndex.ro Integer32 .1.3.6.1.4.1.994.3.4.7.16.1.999 |
pSlotInfoTableTable for configuration of SlotInfo SEQUENCE OF PSlotInfoEntry .1.3.6.1.4.1.994.3.4.7.17 |
pSlotInfoEntryEntry for configuration table of SlotInfo PSlotInfoEntry .1.3.6.1.4.1.994.3.4.7.17.1 |
pSlotInfoDescriptionDescription of the slot contents.ro DescriptionString .1.3.6.1.4.1.994.3.4.7.17.1.3 |
pSlotInfoRecordThe number of records for this slot.ro Integer32 .1.3.6.1.4.1.994.3.4.7.17.1.35 |
pSlotInfoPresentIf true indicates a card is in the slot. If false indicates that no card is present in the slot.ro Boolean .1.3.6.1.4.1.994.3.4.7.17.1.68 |
pSlotInfoSlotIdIdentifies the type of card in slot.ro SlotId .1.3.6.1.4.1.994.3.4.7.17.1.69 |
pSlotInfoIndexIndex.ro Integer32 .1.3.6.1.4.1.994.3.4.7.17.1.999 |
pSlot1TableTable for configuration of Slot1 SEQUENCE OF PSlot1Entry .1.3.6.1.4.1.994.3.4.7.18 |
pSlot1EntryEntry for configuration table of Slot1 PSlot1Entry .1.3.6.1.4.1.994.3.4.7.18.1 |
pSlot1DescriptionThis field is used in the following card types: discrete-inputs - Description of the alarm point. discrete-outputs - Description of the control point. serial-ports - Description of the serial port. onboard-sensors - Description of the onboard device. analog-Inputs - Description of the analog input device. analog-Sensors - Description of the sensor input device.rw DescriptionString .1.3.6.1.4.1.994.3.4.7.18.1.3 |
pSlot1Desc0This field is used in the following card types: discrete-inputs - Description of the off state. discrete-outputs - Description when the control point is open. onboard-sensors - The description for values between threshold 0 and threshold 1. analog-Inputs - The description for values between threshold 0 and threshold 1. analog-Sensors - The description for values between threshold 0 and threshold 1.rw DescriptionString .1.3.6.1.4.1.994.3.4.7.18.1.4 |
pSlot1Desc1This field is used in the following card types: discrete-inputs - Description of the on state. discrete-outputs - Description when the control point is closed. onboard-sensors - The description for values between threshold 1 and threshold 2. analog-Inputs - The description for values between threshold 1 and threshold 2. analog-Sensors - The description for values between threshold 1 and threshold 2.rw DescriptionString .1.3.6.1.4.1.994.3.4.7.18.1.5 |
pSlot1Desc2This field is used in the following card types: onboard-sensors - The description for values between threshold 2 and threshold 3. analog-Inputs - The description for values between threshold 2 and threshold 3. analog-Sensors - The description for values between threshold 2 and threshold 3.rw DescriptionString .1.3.6.1.4.1.994.3.4.7.18.1.6 |
pSlot1Desc3This field is used in the following card types: onboard-sensors - The description for values between threshold 3 and threshold 4. analog-Inputs - The description for values between threshold 3 and threshold 4. analog-Sensors - The description for values between threshold 3 and threshold 4.rw DescriptionString .1.3.6.1.4.1.994.3.4.7.18.1.7 |
pSlot1Desc4This field is used in the following card types: onboard-sensors - The description for values between threshold 4 and threshold 5. analog-Inputs - The description for values between threshold 4 and threshold 5. analog-Sensors - The description for values between threshold 4 and threshold 5.rw DescriptionString .1.3.6.1.4.1.994.3.4.7.18.1.8 |
pSlot1Desc5This field is used in the following card types: analog-Inputs - Description for a communications failure to the sensor. analog-Sensors - Description for a communications failure to the sensor.rw DescriptionString .1.3.6.1.4.1.994.3.4.7.18.1.9 |
pSlot1ConfiguredThis field is used in the following card types: discrete-inputs - If set to true, changes of state will be reported. If set to false, not change of states will be reported. discrete-outputs - If set to true, the control point will operate. If false, it will not operate. serial-ports - If set to true, this serial port will be usable. If set to false the port will not be usable. onboard-sensors - If set to true, the onboard sensors will be used. If set to false the will be ignored. analog-Inputs - If set to true, the analog inputs will be usable. If set to false the analog inputs will be ignored. analog-Sensors - If set to true, the sensor inputs will be usable. If set to false the sensor inputs will be ignored.rw Configured .1.3.6.1.4.1.994.3.4.7.18.1.10 |
pSlot1SendEmailThis field is used in the following card types: discrete-inputs - If set to true, an email will be sent on a change of state. If false, no email will be sent. onboard-sensors - If set to true an email event will be set when a threshold is crossed. If set to false no email event will be sent. analog-Inputs - If set to true an email event will be set when a threshold is crossed. If set to false no email event will be sent. analog-Sensors - If set to true an email event will be set when a threshold is crossed. If set to false no email event will be sent.rw Boolean .1.3.6.1.4.1.994.3.4.7.18.1.11 |
pSlot1SendSNMPTrapThis field is used in the following card types: discrete-inputs - If set to true, an SNMP trap will be sent on a change of state. If false, no SNMP trap will be sent. onboard-sensors - If set to true an SNMP trap will be set when a threshold is crossed. If set to false no SNMP trap will be sent. analog-Inputs - If set to true an SNMP trap will be set when a threshold is crossed. If set to false no SNMP trap will be sent. analog-Sensors - If set to true an SNMP trap will be set when a threshold is crossed. If set to false no SNMP trap will be sent.rw Boolean .1.3.6.1.4.1.994.3.4.7.18.1.12 |
pSlot1IpAddressThis field is used in the following card types: serial-ports - IP Address of the target device.rw IpAddress .1.3.6.1.4.1.994.3.4.7.18.1.14 |
pSlot1Level0This field is used in the following card types: discrete-inputs - Level of the off state. discrete-outputs - Level of the control point when open. onboard-sensors - The level for values between threshold 0 and threshold 1. analog-Inputs - The level for values between threshold 0 and threshold 1. analog-Sensors - The level for values between threshold 0 and threshold 1.rw Level .1.3.6.1.4.1.994.3.4.7.18.1.17 |
pSlot1Level1This field is used in the following card types: discrete-inputs - Level of the on state. discrete-outputs - Level of the control point when closed. onboard-sensors - The level for values between threshold 1 and threshold 2. analog-Inputs - The level for values between threshold 1 and threshold 2. analog-Sensors - The level for values between threshold 1 and threshold 2.rw Level .1.3.6.1.4.1.994.3.4.7.18.1.18 |
pSlot1Level2This field is used in the following card types: onboard-sensors - The level for values between threshold 2 and threshold 3. analog-Inputs - The level for values between threshold 2 and threshold 3. analog-Sensors - The level for values between threshold 2 and threshold 3.rw Level .1.3.6.1.4.1.994.3.4.7.18.1.19 |
pSlot1Level3This field is used in the following card types: onboard-sensors - The level for values between threshold 3 and threshold 4. analog-Inputs - The level for values between threshold 3 and threshold 4. analog-Sensors - The level for values between threshold 3 and threshold 4.rw Level .1.3.6.1.4.1.994.3.4.7.18.1.20 |
pSlot1Level4This field is used in the following card types: onboard-sensors - The level for values between threshold 4 and threshold 5. analog-Inputs - The level for values between threshold 4 and threshold 5. analog-Sensors - The level for values between threshold 4 and threshold 5.rw Level .1.3.6.1.4.1.994.3.4.7.18.1.21 |
pSlot1Level5This field is used in the following card types: analog-Inputs - Level of a communications failure to the sensor. analog-Sensors - Level of a communications failure to the sensor.rw Level .1.3.6.1.4.1.994.3.4.7.18.1.22 |
pSlot1ReadPeriodThis field is used in the following card types: serial-ports - Inactivity timeout (in minutes).rw Integer32 .1.3.6.1.4.1.994.3.4.7.18.1.23 |
pSlot1Thresh0This field is used in the following card types: onboard-sensors - This is the minimun analog value. analog-Inputs - This is the maximum analog value. analog-Sensors - This is the maximum analog value.ro DescriptionString .1.3.6.1.4.1.994.3.4.7.18.1.28 |
pSlot1Thresh1This field is used in the following card types: onboard-sensors - This is the first threshold value. analog-Inputs - This is the first threshold value. analog-Sensors - This is the first threshold value.rw DescriptionString .1.3.6.1.4.1.994.3.4.7.18.1.29 |
pSlot1Thresh2This field is used in the following card types: onboard-sensors - This is the second threshold value. analog-Inputs - This is the second threshold value. analog-Sensors - This is the second threshold value.rw DescriptionString .1.3.6.1.4.1.994.3.4.7.18.1.30 |
pSlot1Thresh3This field is used in the following card types: onboard-sensors - This is the third threshold value. analog-Inputs - This is the third threshold value. analog-Sensors - This is the third threshold value.rw DescriptionString .1.3.6.1.4.1.994.3.4.7.18.1.31 |
pSlot1Thresh4This field is used in the following card types: onboard-sensors - This is the fourth threshold value. analog-Inputs - This is the fourth threshold value. analog-Sensors - This is the fourth threshold value.rw DescriptionString .1.3.6.1.4.1.994.3.4.7.18.1.32 |
pSlot1Thresh5This field is used in the following card types: onboard-sensors - This is the maximum threshold value. analog-Inputs - This is the minimum threshold value. analog-Sensors - This is the minimum threshold value.ro DescriptionString .1.3.6.1.4.1.994.3.4.7.18.1.33 |
pSlot1ContactStyleThis field is used in the following card types: discrete-inputs - Determines the type of contact.rw ContactStyle .1.3.6.1.4.1.994.3.4.7.18.1.44 |
pSlot1UnitsThis field is used in the following card types: onboard-sensors - Description of the units of measurement. analog-Inputs - Description of the units of measurement. analog-Sensors - Description of the units of measurement.ro DescriptionString .1.3.6.1.4.1.994.3.4.7.18.1.46 |
pSlot1OutputModeThis field is used in the following card types: discrete-outputs - Defines the different ways a control point can be activated.rw OutputMode .1.3.6.1.4.1.994.3.4.7.18.1.47 |
pSlot1OutputStateThis field is used in the following card types: discrete-outputs - A value of 0 will open the control point. A value of 1 will close the control point.rw OutputState .1.3.6.1.4.1.994.3.4.7.18.1.48 |
pSlot1OutputAutoThis field is used in the following card types: discrete-outputs - When this control point is opened, this alarm point will change state to the on state.rw Integer32 .1.3.6.1.4.1.994.3.4.7.18.1.49 |
pSlot1BaudRateThis field is used in the following card types: serial-ports - Baud rate of the serial port.rw BaudRate .1.3.6.1.4.1.994.3.4.7.18.1.57 |
pSlot1DataBitsThis field is used in the following card types: serial-ports - Number of data bit for the serial port.rw DataBits .1.3.6.1.4.1.994.3.4.7.18.1.58 |
pSlot1ParityThis field is used in the following card types: serial-ports - Parity of the serial port.rw Parity .1.3.6.1.4.1.994.3.4.7.18.1.59 |
pSlot1StopBitsThis field is used in the following card types: serial-ports - Number of stop bits for the serial port.rw StopBits .1.3.6.1.4.1.994.3.4.7.18.1.60 |
pSlot1ProtocolThis field is used in the following card types: serial-ports - Protocol the serial port is speaking.rw Protocol .1.3.6.1.4.1.994.3.4.7.18.1.61 |
pSlot1SerialRTSThis field is used in the following card types: serial-ports - Request To Send (RTS) setting for the serial port.rw SerialRTS .1.3.6.1.4.1.994.3.4.7.18.1.62 |
pSlot1SerialCTSThis field is used in the following card types: serial-ports - Clear To Send (CTS) setting for the serial port.rw SerialCTS .1.3.6.1.4.1.994.3.4.7.18.1.63 |
pSlot1LiveDescriptionThis field is used in the following card types: discrete-inputs - The current description of the alarm state. onboard-sensors - The description of the current state of the onboard sensor analog-Inputs - The description of the current state of the analog input. analog-Sensors - The description of the current state of the sensor input.ro DescriptionString .1.3.6.1.4.1.994.3.4.7.18.1.64 |
pSlot1LiveLevelThis field is used in the following card types: discrete-inputs - The current level of the alarm. onboard-sensors - The level of the current state of the onboard sensor. analog-Inputs - The level of the current state of the analog input. analog-Sensors - The level of the current state of the sensor input.ro DescriptionString .1.3.6.1.4.1.994.3.4.7.18.1.65 |
pSlot1LiveRawThis field is used in the following card types: onboard-sensors - The current reading from the onboard sensor. This value will always be between the threshold 0 and threshold 5 values. analog-Inputs - The current reading from the analog input. This value will always be between the threshold 0 and threshold 5 values. analog-Sensors - The current reading from the sensor input. This value will always be between the threshold 0 and threshold 5 values.ro DescriptionString .1.3.6.1.4.1.994.3.4.7.18.1.66 |
pSlot1LiveTimeThis field is used in the following card types: discrete-inputs - The time of the last change of state. onboard-sensors - The time of the last event. analog-Inputs - The time of the last event. analog-Sensors - The time of the last event.ro DescriptionString .1.3.6.1.4.1.994.3.4.7.18.1.67 |
pSlot1PresentThis field is used in the following card types: serial-ports - If set to true, the serial port exists. If set to false the serial port does not exist.ro Boolean .1.3.6.1.4.1.994.3.4.7.18.1.68 |
pSlot1OutputAutoPkgThis field is used in the following card types: discrete-outputs - When this control point is opened, this is the package that the alarm point is located.rw Integer32 .1.3.6.1.4.1.994.3.4.7.18.1.71 |
pSlot1VoltageRangeThis field is used in the following card types: onboard-sensors - The voltage range. analog-Inputs - The voltage range. analog-Sensors - The voltage range.ro VoltageRange .1.3.6.1.4.1.994.3.4.7.18.1.72 |
pSlot1IPPortNumThis field is used in the following card types: serial-ports - IP port number of the target device.rw Integer32 .1.3.6.1.4.1.994.3.4.7.18.1.73 |
pSlot1IOFormatThis field is used in the following card types: discrete-inputs - The io format of discrete inputs. discrete-outputs - The io format of discrete outputs. serial-ports - The io format of serial ports. onboard-sensors - The io format of onboard sensors. analog-Inputs - The io format of analog inputs. analog-Sensors - The io format of analog sensors.ro IOFormat .1.3.6.1.4.1.994.3.4.7.18.1.75 |
pSlot1PortTypeThis field is used in the following card types: serial-ports - The type of serial port.ro PortType .1.3.6.1.4.1.994.3.4.7.18.1.76 |
pSlot1TL1SIDThis field is used in the following card types: discrete-inputs - discrete-outputs - onboard-sensors - analog-Inputs - analog-Sensors -rw DescriptionString .1.3.6.1.4.1.994.3.4.7.18.1.116 |
pSlot1TL1CONDThis field is used in the following card types: discrete-inputs - discrete-outputs - onboard-sensors - analog-Inputs - analog-Sensors -rw DescriptionString .1.3.6.1.4.1.994.3.4.7.18.1.117 |
pSlot1TL1EqptThis field is used in the following card types: discrete-inputs - onboard-sensors - analog-Inputs - analog-Sensors -rw DescriptionString .1.3.6.1.4.1.994.3.4.7.18.1.118 |
pSlot1TL1EnvThis field is used in the following card types: discrete-inputs - onboard-sensors - analog-Inputs - analog-Sensors -rw Boolean .1.3.6.1.4.1.994.3.4.7.18.1.119 |
pSlot1TL1SrveffThis field is used in the following card types: discrete-inputs - onboard-sensors - analog-Inputs - analog-Sensors -rw TL1Srveff .1.3.6.1.4.1.994.3.4.7.18.1.120 |
pSlot1TL1LocnThis field is used in the following card types: discrete-inputs - onboard-sensors - analog-Inputs - analog-Sensors -rw TL1Locn .1.3.6.1.4.1.994.3.4.7.18.1.121 |
pSlot1TL1DirnThis field is used in the following card types: discrete-inputs - onboard-sensors - analog-Inputs - analog-Sensors -rw TL1Dirn .1.3.6.1.4.1.994.3.4.7.18.1.122 |
pSlot1SensorTypeThis field is used in the following card types: analog-Inputs - The type of sensor. analog-Sensors - The type of sensor.rw SensorType .1.3.6.1.4.1.994.3.4.7.18.1.131 |
pSlot1IndexIndex.ro Integer32 .1.3.6.1.4.1.994.3.4.7.18.1.999 |
pSlot2TableTable for configuration of Slot2 SEQUENCE OF PSlot2Entry .1.3.6.1.4.1.994.3.4.7.19 |
pSlot2EntryEntry for configuration table of Slot2 PSlot2Entry .1.3.6.1.4.1.994.3.4.7.19.1 |
pSlot2DescriptionThis field is used in the following card types: discrete-inputs - Description of the alarm point. discrete-outputs - Description of the control point. serial-ports - Description of the serial port. onboard-sensors - Description of the onboard device. analog-Inputs - Description of the analog input device. analog-Sensors - Description of the sensor input device.rw DescriptionString .1.3.6.1.4.1.994.3.4.7.19.1.3 |
pSlot2Desc0This field is used in the following card types: discrete-inputs - Description of the off state. discrete-outputs - Description when the control point is open. onboard-sensors - The description for values between threshold 0 and threshold 1. analog-Inputs - The description for values between threshold 0 and threshold 1. analog-Sensors - The description for values between threshold 0 and threshold 1.rw DescriptionString .1.3.6.1.4.1.994.3.4.7.19.1.4 |
pSlot2Desc1This field is used in the following card types: discrete-inputs - Description of the on state. discrete-outputs - Description when the control point is closed. onboard-sensors - The description for values between threshold 1 and threshold 2. analog-Inputs - The description for values between threshold 1 and threshold 2. analog-Sensors - The description for values between threshold 1 and threshold 2.rw DescriptionString .1.3.6.1.4.1.994.3.4.7.19.1.5 |
pSlot2Desc2This field is used in the following card types: onboard-sensors - The description for values between threshold 2 and threshold 3. analog-Inputs - The description for values between threshold 2 and threshold 3. analog-Sensors - The description for values between threshold 2 and threshold 3.rw DescriptionString .1.3.6.1.4.1.994.3.4.7.19.1.6 |
pSlot2Desc3This field is used in the following card types: onboard-sensors - The description for values between threshold 3 and threshold 4. analog-Inputs - The description for values between threshold 3 and threshold 4. analog-Sensors - The description for values between threshold 3 and threshold 4.rw DescriptionString .1.3.6.1.4.1.994.3.4.7.19.1.7 |
pSlot2Desc4This field is used in the following card types: onboard-sensors - The description for values between threshold 4 and threshold 5. analog-Inputs - The description for values between threshold 4 and threshold 5. analog-Sensors - The description for values between threshold 4 and threshold 5.rw DescriptionString .1.3.6.1.4.1.994.3.4.7.19.1.8 |
pSlot2Desc5This field is used in the following card types: analog-Inputs - Description for a communications failure to the sensor. analog-Sensors - Description for a communications failure to the sensor.rw DescriptionString .1.3.6.1.4.1.994.3.4.7.19.1.9 |
pSlot2ConfiguredThis field is used in the following card types: discrete-inputs - If set to true, changes of state will be reported. If set to false, not change of states will be reported. discrete-outputs - If set to true, the control point will operate. If false, it will not operate. serial-ports - If set to true, this serial port will be usable. If set to false the port will not be usable. onboard-sensors - If set to true, the onboard sensors will be used. If set to false the will be ignored. analog-Inputs - If set to true, the analog inputs will be usable. If set to false the analog inputs will be ignored. analog-Sensors - If set to true, the sensor inputs will be usable. If set to false the sensor inputs will be ignored.rw Configured .1.3.6.1.4.1.994.3.4.7.19.1.10 |
pSlot2SendEmailThis field is used in the following card types: discrete-inputs - If set to true, an email will be sent on a change of state. If false, no email will be sent. onboard-sensors - If set to true an email event will be set when a threshold is crossed. If set to false no email event will be sent. analog-Inputs - If set to true an email event will be set when a threshold is crossed. If set to false no email event will be sent. analog-Sensors - If set to true an email event will be set when a threshold is crossed. If set to false no email event will be sent.rw Boolean .1.3.6.1.4.1.994.3.4.7.19.1.11 |
pSlot2SendSNMPTrapThis field is used in the following card types: discrete-inputs - If set to true, an SNMP trap will be sent on a change of state. If false, no SNMP trap will be sent. onboard-sensors - If set to true an SNMP trap will be set when a threshold is crossed. If set to false no SNMP trap will be sent. analog-Inputs - If set to true an SNMP trap will be set when a threshold is crossed. If set to false no SNMP trap will be sent. analog-Sensors - If set to true an SNMP trap will be set when a threshold is crossed. If set to false no SNMP trap will be sent.rw Boolean .1.3.6.1.4.1.994.3.4.7.19.1.12 |
pSlot2IpAddressThis field is used in the following card types: serial-ports - IP Address of the target device.rw IpAddress .1.3.6.1.4.1.994.3.4.7.19.1.14 |
pSlot2Level0This field is used in the following card types: discrete-inputs - Level of the off state. discrete-outputs - Level of the control point when open. onboard-sensors - The level for values between threshold 0 and threshold 1. analog-Inputs - The level for values between threshold 0 and threshold 1. analog-Sensors - The level for values between threshold 0 and threshold 1.rw Level .1.3.6.1.4.1.994.3.4.7.19.1.17 |
pSlot2Level1This field is used in the following card types: discrete-inputs - Level of the on state. discrete-outputs - Level of the control point when closed. onboard-sensors - The level for values between threshold 1 and threshold 2. analog-Inputs - The level for values between threshold 1 and threshold 2. analog-Sensors - The level for values between threshold 1 and threshold 2.rw Level .1.3.6.1.4.1.994.3.4.7.19.1.18 |
pSlot2Level2This field is used in the following card types: onboard-sensors - The level for values between threshold 2 and threshold 3. analog-Inputs - The level for values between threshold 2 and threshold 3. analog-Sensors - The level for values between threshold 2 and threshold 3.rw Level .1.3.6.1.4.1.994.3.4.7.19.1.19 |
pSlot2Level3This field is used in the following card types: onboard-sensors - The level for values between threshold 3 and threshold 4. analog-Inputs - The level for values between threshold 3 and threshold 4. analog-Sensors - The level for values between threshold 3 and threshold 4.rw Level .1.3.6.1.4.1.994.3.4.7.19.1.20 |
pSlot2Level4This field is used in the following card types: onboard-sensors - The level for values between threshold 4 and threshold 5. analog-Inputs - The level for values between threshold 4 and threshold 5. analog-Sensors - The level for values between threshold 4 and threshold 5.rw Level .1.3.6.1.4.1.994.3.4.7.19.1.21 |
pSlot2Level5This field is used in the following card types: analog-Inputs - Level of a communications failure to the sensor. analog-Sensors - Level of a communications failure to the sensor.rw Level .1.3.6.1.4.1.994.3.4.7.19.1.22 |
pSlot2ReadPeriodThis field is used in the following card types: serial-ports - Inactivity timeout (in minutes).rw Integer32 .1.3.6.1.4.1.994.3.4.7.19.1.23 |
pSlot2Thresh0This field is used in the following card types: onboard-sensors - This is the minimun analog value. analog-Inputs - This is the maximum analog value. analog-Sensors - This is the maximum analog value.ro DescriptionString .1.3.6.1.4.1.994.3.4.7.19.1.28 |
pSlot2Thresh1This field is used in the following card types: onboard-sensors - This is the first threshold value. analog-Inputs - This is the first threshold value. analog-Sensors - This is the first threshold value.rw DescriptionString .1.3.6.1.4.1.994.3.4.7.19.1.29 |
pSlot2Thresh2This field is used in the following card types: onboard-sensors - This is the second threshold value. analog-Inputs - This is the second threshold value. analog-Sensors - This is the second threshold value.rw DescriptionString .1.3.6.1.4.1.994.3.4.7.19.1.30 |
pSlot2Thresh3This field is used in the following card types: onboard-sensors - This is the third threshold value. analog-Inputs - This is the third threshold value. analog-Sensors - This is the third threshold value.rw DescriptionString .1.3.6.1.4.1.994.3.4.7.19.1.31 |
pSlot2Thresh4This field is used in the following card types: onboard-sensors - This is the fourth threshold value. analog-Inputs - This is the fourth threshold value. analog-Sensors - This is the fourth threshold value.rw DescriptionString .1.3.6.1.4.1.994.3.4.7.19.1.32 |
pSlot2Thresh5This field is used in the following card types: onboard-sensors - This is the maximum threshold value. analog-Inputs - This is the minimum threshold value. analog-Sensors - This is the minimum threshold value.ro DescriptionString .1.3.6.1.4.1.994.3.4.7.19.1.33 |
pSlot2ContactStyleThis field is used in the following card types: discrete-inputs - Determines the type of contact.rw ContactStyle .1.3.6.1.4.1.994.3.4.7.19.1.44 |
pSlot2UnitsThis field is used in the following card types: onboard-sensors - Description of the units of measurement. analog-Inputs - Description of the units of measurement. analog-Sensors - Description of the units of measurement.ro DescriptionString .1.3.6.1.4.1.994.3.4.7.19.1.46 |
pSlot2OutputModeThis field is used in the following card types: discrete-outputs - Defines the different ways a control point can be activated.rw OutputMode .1.3.6.1.4.1.994.3.4.7.19.1.47 |
pSlot2OutputStateThis field is used in the following card types: discrete-outputs - A value of 0 will open the control point. A value of 1 will close the control point.rw OutputState .1.3.6.1.4.1.994.3.4.7.19.1.48 |
pSlot2OutputAutoThis field is used in the following card types: discrete-outputs - When this control point is opened, this alarm point will change state to the on state.rw Integer32 .1.3.6.1.4.1.994.3.4.7.19.1.49 |
pSlot2BaudRateThis field is used in the following card types: serial-ports - Baud rate of the serial port.rw BaudRate .1.3.6.1.4.1.994.3.4.7.19.1.57 |
pSlot2DataBitsThis field is used in the following card types: serial-ports - Number of data bit for the serial port.rw DataBits .1.3.6.1.4.1.994.3.4.7.19.1.58 |
pSlot2ParityThis field is used in the following card types: serial-ports - Parity of the serial port.rw Parity .1.3.6.1.4.1.994.3.4.7.19.1.59 |
pSlot2StopBitsThis field is used in the following card types: serial-ports - Number of stop bits for the serial port.rw StopBits .1.3.6.1.4.1.994.3.4.7.19.1.60 |
pSlot2ProtocolThis field is used in the following card types: serial-ports - Protocol the serial port is speaking.rw Protocol .1.3.6.1.4.1.994.3.4.7.19.1.61 |
pSlot2SerialRTSThis field is used in the following card types: serial-ports - Request To Send (RTS) setting for the serial port.rw SerialRTS .1.3.6.1.4.1.994.3.4.7.19.1.62 |
pSlot2SerialCTSThis field is used in the following card types: serial-ports - Clear To Send (CTS) setting for the serial port.rw SerialCTS .1.3.6.1.4.1.994.3.4.7.19.1.63 |
pSlot2LiveDescriptionThis field is used in the following card types: discrete-inputs - The current description of the alarm state. onboard-sensors - The description of the current state of the onboard sensor analog-Inputs - The description of the current state of the analog input. analog-Sensors - The description of the current state of the sensor input.ro DescriptionString .1.3.6.1.4.1.994.3.4.7.19.1.64 |
pSlot2LiveLevelThis field is used in the following card types: discrete-inputs - The current level of the alarm. onboard-sensors - The level of the current state of the onboard sensor. analog-Inputs - The level of the current state of the analog input. analog-Sensors - The level of the current state of the sensor input.ro DescriptionString .1.3.6.1.4.1.994.3.4.7.19.1.65 |
pSlot2LiveRawThis field is used in the following card types: onboard-sensors - The current reading from the onboard sensor. This value will always be between the threshold 0 and threshold 5 values. analog-Inputs - The current reading from the analog input. This value will always be between the threshold 0 and threshold 5 values. analog-Sensors - The current reading from the sensor input. This value will always be between the threshold 0 and threshold 5 values.ro DescriptionString .1.3.6.1.4.1.994.3.4.7.19.1.66 |
pSlot2LiveTimeThis field is used in the following card types: discrete-inputs - The time of the last change of state. onboard-sensors - The time of the last event. analog-Inputs - The time of the last event. analog-Sensors - The time of the last event.ro DescriptionString .1.3.6.1.4.1.994.3.4.7.19.1.67 |
pSlot2PresentThis field is used in the following card types: serial-ports - If set to true, the serial port exists. If set to false the serial port does not exist.ro Boolean .1.3.6.1.4.1.994.3.4.7.19.1.68 |
pSlot2OutputAutoPkgThis field is used in the following card types: discrete-outputs - When this control point is opened, this is the package that the alarm point is located.rw Integer32 .1.3.6.1.4.1.994.3.4.7.19.1.71 |
pSlot2VoltageRangeThis field is used in the following card types: onboard-sensors - The voltage range. analog-Inputs - The voltage range. analog-Sensors - The voltage range.ro VoltageRange .1.3.6.1.4.1.994.3.4.7.19.1.72 |
pSlot2IPPortNumThis field is used in the following card types: serial-ports - IP port number of the target device.rw Integer32 .1.3.6.1.4.1.994.3.4.7.19.1.73 |
pSlot2IOFormatThis field is used in the following card types: discrete-inputs - The io format of discrete inputs. discrete-outputs - The io format of discrete outputs. serial-ports - The io format of serial ports. onboard-sensors - The io format of onboard sensors. analog-Inputs - The io format of analog inputs. analog-Sensors - The io format of analog sensors.ro IOFormat .1.3.6.1.4.1.994.3.4.7.19.1.75 |
pSlot2PortTypeThis field is used in the following card types: serial-ports - The type of serial port.ro PortType .1.3.6.1.4.1.994.3.4.7.19.1.76 |
pSlot2TL1SIDThis field is used in the following card types: discrete-inputs - discrete-outputs - onboard-sensors - analog-Inputs - analog-Sensors -rw DescriptionString .1.3.6.1.4.1.994.3.4.7.19.1.116 |
pSlot2TL1CONDThis field is used in the following card types: discrete-inputs - discrete-outputs - onboard-sensors - analog-Inputs - analog-Sensors -rw DescriptionString .1.3.6.1.4.1.994.3.4.7.19.1.117 |
pSlot2TL1EqptThis field is used in the following card types: discrete-inputs - onboard-sensors - analog-Inputs - analog-Sensors -rw DescriptionString .1.3.6.1.4.1.994.3.4.7.19.1.118 |
pSlot2TL1EnvThis field is used in the following card types: discrete-inputs - onboard-sensors - analog-Inputs - analog-Sensors -rw Boolean .1.3.6.1.4.1.994.3.4.7.19.1.119 |
pSlot2TL1SrveffThis field is used in the following card types: discrete-inputs - onboard-sensors - analog-Inputs - analog-Sensors -rw TL1Srveff .1.3.6.1.4.1.994.3.4.7.19.1.120 |
pSlot2TL1LocnThis field is used in the following card types: discrete-inputs - onboard-sensors - analog-Inputs - analog-Sensors -rw TL1Locn .1.3.6.1.4.1.994.3.4.7.19.1.121 |
pSlot2TL1DirnThis field is used in the following card types: discrete-inputs - onboard-sensors - analog-Inputs - analog-Sensors -rw TL1Dirn .1.3.6.1.4.1.994.3.4.7.19.1.122 |
pSlot2SensorTypeThis field is used in the following card types: analog-Inputs - The type of sensor. analog-Sensors - The type of sensor.rw SensorType .1.3.6.1.4.1.994.3.4.7.19.1.131 |
pSlot2IndexIndex.ro Integer32 .1.3.6.1.4.1.994.3.4.7.19.1.999 |
pSlot3TableTable for configuration of Slot3 SEQUENCE OF PSlot3Entry .1.3.6.1.4.1.994.3.4.7.20 |
pSlot3EntryEntry for configuration table of Slot3 PSlot3Entry .1.3.6.1.4.1.994.3.4.7.20.1 |
pSlot3DescriptionThis field is used in the following card types: discrete-inputs - Description of the alarm point. discrete-outputs - Description of the control point. serial-ports - Description of the serial port. onboard-sensors - Description of the onboard device. analog-Inputs - Description of the analog input device. analog-Sensors - Description of the sensor input device.rw DescriptionString .1.3.6.1.4.1.994.3.4.7.20.1.3 |
pSlot3Desc0This field is used in the following card types: discrete-inputs - Description of the off state. discrete-outputs - Description when the control point is open. onboard-sensors - The description for values between threshold 0 and threshold 1. analog-Inputs - The description for values between threshold 0 and threshold 1. analog-Sensors - The description for values between threshold 0 and threshold 1.rw DescriptionString .1.3.6.1.4.1.994.3.4.7.20.1.4 |
pSlot3Desc1This field is used in the following card types: discrete-inputs - Description of the on state. discrete-outputs - Description when the control point is closed. onboard-sensors - The description for values between threshold 1 and threshold 2. analog-Inputs - The description for values between threshold 1 and threshold 2. analog-Sensors - The description for values between threshold 1 and threshold 2.rw DescriptionString .1.3.6.1.4.1.994.3.4.7.20.1.5 |
pSlot3Desc2This field is used in the following card types: onboard-sensors - The description for values between threshold 2 and threshold 3. analog-Inputs - The description for values between threshold 2 and threshold 3. analog-Sensors - The description for values between threshold 2 and threshold 3.rw DescriptionString .1.3.6.1.4.1.994.3.4.7.20.1.6 |
pSlot3Desc3This field is used in the following card types: onboard-sensors - The description for values between threshold 3 and threshold 4. analog-Inputs - The description for values between threshold 3 and threshold 4. analog-Sensors - The description for values between threshold 3 and threshold 4.rw DescriptionString .1.3.6.1.4.1.994.3.4.7.20.1.7 |
pSlot3Desc4This field is used in the following card types: onboard-sensors - The description for values between threshold 4 and threshold 5. analog-Inputs - The description for values between threshold 4 and threshold 5. analog-Sensors - The description for values between threshold 4 and threshold 5.rw DescriptionString .1.3.6.1.4.1.994.3.4.7.20.1.8 |
pSlot3Desc5This field is used in the following card types: analog-Inputs - Description for a communications failure to the sensor. analog-Sensors - Description for a communications failure to the sensor.rw DescriptionString .1.3.6.1.4.1.994.3.4.7.20.1.9 |
pSlot3ConfiguredThis field is used in the following card types: discrete-inputs - If set to true, changes of state will be reported. If set to false, not change of states will be reported. discrete-outputs - If set to true, the control point will operate. If false, it will not operate. serial-ports - If set to true, this serial port will be usable. If set to false the port will not be usable. onboard-sensors - If set to true, the onboard sensors will be used. If set to false the will be ignored. analog-Inputs - If set to true, the analog inputs will be usable. If set to false the analog inputs will be ignored. analog-Sensors - If set to true, the sensor inputs will be usable. If set to false the sensor inputs will be ignored.rw Configured .1.3.6.1.4.1.994.3.4.7.20.1.10 |
pSlot3SendEmailThis field is used in the following card types: discrete-inputs - If set to true, an email will be sent on a change of state. If false, no email will be sent. onboard-sensors - If set to true an email event will be set when a threshold is crossed. If set to false no email event will be sent. analog-Inputs - If set to true an email event will be set when a threshold is crossed. If set to false no email event will be sent. analog-Sensors - If set to true an email event will be set when a threshold is crossed. If set to false no email event will be sent.rw Boolean .1.3.6.1.4.1.994.3.4.7.20.1.11 |
pSlot3SendSNMPTrapThis field is used in the following card types: discrete-inputs - If set to true, an SNMP trap will be sent on a change of state. If false, no SNMP trap will be sent. onboard-sensors - If set to true an SNMP trap will be set when a threshold is crossed. If set to false no SNMP trap will be sent. analog-Inputs - If set to true an SNMP trap will be set when a threshold is crossed. If set to false no SNMP trap will be sent. analog-Sensors - If set to true an SNMP trap will be set when a threshold is crossed. If set to false no SNMP trap will be sent.rw Boolean .1.3.6.1.4.1.994.3.4.7.20.1.12 |
pSlot3IpAddressThis field is used in the following card types: serial-ports - IP Address of the target device.rw IpAddress .1.3.6.1.4.1.994.3.4.7.20.1.14 |
pSlot3Level0This field is used in the following card types: discrete-inputs - Level of the off state. discrete-outputs - Level of the control point when open. onboard-sensors - The level for values between threshold 0 and threshold 1. analog-Inputs - The level for values between threshold 0 and threshold 1. analog-Sensors - The level for values between threshold 0 and threshold 1.rw Level .1.3.6.1.4.1.994.3.4.7.20.1.17 |
pSlot3Level1This field is used in the following card types: discrete-inputs - Level of the on state. discrete-outputs - Level of the control point when closed. onboard-sensors - The level for values between threshold 1 and threshold 2. analog-Inputs - The level for values between threshold 1 and threshold 2. analog-Sensors - The level for values between threshold 1 and threshold 2.rw Level .1.3.6.1.4.1.994.3.4.7.20.1.18 |
pSlot3Level2This field is used in the following card types: onboard-sensors - The level for values between threshold 2 and threshold 3. analog-Inputs - The level for values between threshold 2 and threshold 3. analog-Sensors - The level for values between threshold 2 and threshold 3.rw Level .1.3.6.1.4.1.994.3.4.7.20.1.19 |
pSlot3Level3This field is used in the following card types: onboard-sensors - The level for values between threshold 3 and threshold 4. analog-Inputs - The level for values between threshold 3 and threshold 4. analog-Sensors - The level for values between threshold 3 and threshold 4.rw Level .1.3.6.1.4.1.994.3.4.7.20.1.20 |
pSlot3Level4This field is used in the following card types: onboard-sensors - The level for values between threshold 4 and threshold 5. analog-Inputs - The level for values between threshold 4 and threshold 5. analog-Sensors - The level for values between threshold 4 and threshold 5.rw Level .1.3.6.1.4.1.994.3.4.7.20.1.21 |
pSlot3Level5This field is used in the following card types: analog-Inputs - Level of a communications failure to the sensor. analog-Sensors - Level of a communications failure to the sensor.rw Level .1.3.6.1.4.1.994.3.4.7.20.1.22 |
pSlot3ReadPeriodThis field is used in the following card types: serial-ports - Inactivity timeout (in minutes).rw Integer32 .1.3.6.1.4.1.994.3.4.7.20.1.23 |
pSlot3Thresh0This field is used in the following card types: onboard-sensors - This is the minimun analog value. analog-Inputs - This is the maximum analog value. analog-Sensors - This is the maximum analog value.ro DescriptionString .1.3.6.1.4.1.994.3.4.7.20.1.28 |
pSlot3Thresh1This field is used in the following card types: onboard-sensors - This is the first threshold value. analog-Inputs - This is the first threshold value. analog-Sensors - This is the first threshold value.rw DescriptionString .1.3.6.1.4.1.994.3.4.7.20.1.29 |
pSlot3Thresh2This field is used in the following card types: onboard-sensors - This is the second threshold value. analog-Inputs - This is the second threshold value. analog-Sensors - This is the second threshold value.rw DescriptionString .1.3.6.1.4.1.994.3.4.7.20.1.30 |
pSlot3Thresh3This field is used in the following card types: onboard-sensors - This is the third threshold value. analog-Inputs - This is the third threshold value. analog-Sensors - This is the third threshold value.rw DescriptionString .1.3.6.1.4.1.994.3.4.7.20.1.31 |
pSlot3Thresh4This field is used in the following card types: onboard-sensors - This is the fourth threshold value. analog-Inputs - This is the fourth threshold value. analog-Sensors - This is the fourth threshold value.rw DescriptionString .1.3.6.1.4.1.994.3.4.7.20.1.32 |
pSlot3Thresh5This field is used in the following card types: onboard-sensors - This is the maximum threshold value. analog-Inputs - This is the minimum threshold value. analog-Sensors - This is the minimum threshold value.ro DescriptionString .1.3.6.1.4.1.994.3.4.7.20.1.33 |
pSlot3ContactStyleThis field is used in the following card types: discrete-inputs - Determines the type of contact.rw ContactStyle .1.3.6.1.4.1.994.3.4.7.20.1.44 |
pSlot3UnitsThis field is used in the following card types: onboard-sensors - Description of the units of measurement. analog-Inputs - Description of the units of measurement. analog-Sensors - Description of the units of measurement.ro DescriptionString .1.3.6.1.4.1.994.3.4.7.20.1.46 |
pSlot3OutputModeThis field is used in the following card types: discrete-outputs - Defines the different ways a control point can be activated.rw OutputMode .1.3.6.1.4.1.994.3.4.7.20.1.47 |
pSlot3OutputStateThis field is used in the following card types: discrete-outputs - A value of 0 will open the control point. A value of 1 will close the control point.rw OutputState .1.3.6.1.4.1.994.3.4.7.20.1.48 |
pSlot3OutputAutoThis field is used in the following card types: discrete-outputs - When this control point is opened, this alarm point will change state to the on state.rw Integer32 .1.3.6.1.4.1.994.3.4.7.20.1.49 |
pSlot3BaudRateThis field is used in the following card types: serial-ports - Baud rate of the serial port.rw BaudRate .1.3.6.1.4.1.994.3.4.7.20.1.57 |
pSlot3DataBitsThis field is used in the following card types: serial-ports - Number of data bit for the serial port.rw DataBits .1.3.6.1.4.1.994.3.4.7.20.1.58 |
pSlot3ParityThis field is used in the following card types: serial-ports - Parity of the serial port.rw Parity .1.3.6.1.4.1.994.3.4.7.20.1.59 |
pSlot3StopBitsThis field is used in the following card types: serial-ports - Number of stop bits for the serial port.rw StopBits .1.3.6.1.4.1.994.3.4.7.20.1.60 |
pSlot3ProtocolThis field is used in the following card types: serial-ports - Protocol the serial port is speaking.rw Protocol .1.3.6.1.4.1.994.3.4.7.20.1.61 |
pSlot3SerialRTSThis field is used in the following card types: serial-ports - Request To Send (RTS) setting for the serial port.rw SerialRTS .1.3.6.1.4.1.994.3.4.7.20.1.62 |
pSlot3SerialCTSThis field is used in the following card types: serial-ports - Clear To Send (CTS) setting for the serial port.rw SerialCTS .1.3.6.1.4.1.994.3.4.7.20.1.63 |
pSlot3LiveDescriptionThis field is used in the following card types: discrete-inputs - The current description of the alarm state. onboard-sensors - The description of the current state of the onboard sensor analog-Inputs - The description of the current state of the analog input. analog-Sensors - The description of the current state of the sensor input.ro DescriptionString .1.3.6.1.4.1.994.3.4.7.20.1.64 |
pSlot3LiveLevelThis field is used in the following card types: discrete-inputs - The current level of the alarm. onboard-sensors - The level of the current state of the onboard sensor. analog-Inputs - The level of the current state of the analog input. analog-Sensors - The level of the current state of the sensor input.ro DescriptionString .1.3.6.1.4.1.994.3.4.7.20.1.65 |
pSlot3LiveRawThis field is used in the following card types: onboard-sensors - The current reading from the onboard sensor. This value will always be between the threshold 0 and threshold 5 values. analog-Inputs - The current reading from the analog input. This value will always be between the threshold 0 and threshold 5 values. analog-Sensors - The current reading from the sensor input. This value will always be between the threshold 0 and threshold 5 values.ro DescriptionString .1.3.6.1.4.1.994.3.4.7.20.1.66 |
pSlot3LiveTimeThis field is used in the following card types: discrete-inputs - The time of the last change of state. onboard-sensors - The time of the last event. analog-Inputs - The time of the last event. analog-Sensors - The time of the last event.ro DescriptionString .1.3.6.1.4.1.994.3.4.7.20.1.67 |
pSlot3PresentThis field is used in the following card types: serial-ports - If set to true, the serial port exists. If set to false the serial port does not exist.ro Boolean .1.3.6.1.4.1.994.3.4.7.20.1.68 |
pSlot3OutputAutoPkgThis field is used in the following card types: discrete-outputs - When this control point is opened, this is the package that the alarm point is located.rw Integer32 .1.3.6.1.4.1.994.3.4.7.20.1.71 |
pSlot3VoltageRangeThis field is used in the following card types: onboard-sensors - The voltage range. analog-Inputs - The voltage range. analog-Sensors - The voltage range.ro VoltageRange .1.3.6.1.4.1.994.3.4.7.20.1.72 |
pSlot3IPPortNumThis field is used in the following card types: serial-ports - IP port number of the target device.rw Integer32 .1.3.6.1.4.1.994.3.4.7.20.1.73 |
pSlot3IOFormatThis field is used in the following card types: discrete-inputs - The io format of discrete inputs. discrete-outputs - The io format of discrete outputs. serial-ports - The io format of serial ports. onboard-sensors - The io format of onboard sensors. analog-Inputs - The io format of analog inputs. analog-Sensors - The io format of analog sensors.ro IOFormat .1.3.6.1.4.1.994.3.4.7.20.1.75 |
pSlot3PortTypeThis field is used in the following card types: serial-ports - The type of serial port.ro PortType .1.3.6.1.4.1.994.3.4.7.20.1.76 |
pSlot3TL1SIDThis field is used in the following card types: discrete-inputs - discrete-outputs - onboard-sensors - analog-Inputs - analog-Sensors -rw DescriptionString .1.3.6.1.4.1.994.3.4.7.20.1.116 |
pSlot3TL1CONDThis field is used in the following card types: discrete-inputs - discrete-outputs - onboard-sensors - analog-Inputs - analog-Sensors -rw DescriptionString .1.3.6.1.4.1.994.3.4.7.20.1.117 |
pSlot3TL1EqptThis field is used in the following card types: discrete-inputs - onboard-sensors - analog-Inputs - analog-Sensors -rw DescriptionString .1.3.6.1.4.1.994.3.4.7.20.1.118 |
pSlot3TL1EnvThis field is used in the following card types: discrete-inputs - onboard-sensors - analog-Inputs - analog-Sensors -rw Boolean .1.3.6.1.4.1.994.3.4.7.20.1.119 |
pSlot3TL1SrveffThis field is used in the following card types: discrete-inputs - onboard-sensors - analog-Inputs - analog-Sensors -rw TL1Srveff .1.3.6.1.4.1.994.3.4.7.20.1.120 |
pSlot3TL1LocnThis field is used in the following card types: discrete-inputs - onboard-sensors - analog-Inputs - analog-Sensors -rw TL1Locn .1.3.6.1.4.1.994.3.4.7.20.1.121 |
pSlot3TL1DirnThis field is used in the following card types: discrete-inputs - onboard-sensors - analog-Inputs - analog-Sensors -rw TL1Dirn .1.3.6.1.4.1.994.3.4.7.20.1.122 |
pSlot3SensorTypeThis field is used in the following card types: analog-Inputs - The type of sensor. analog-Sensors - The type of sensor.rw SensorType .1.3.6.1.4.1.994.3.4.7.20.1.131 |
pSlot3IndexIndex.ro Integer32 .1.3.6.1.4.1.994.3.4.7.20.1.999 |
pSlot4TableTable for configuration of Slot4 SEQUENCE OF PSlot4Entry .1.3.6.1.4.1.994.3.4.7.21 |
pSlot4EntryEntry for configuration table of Slot4 PSlot4Entry .1.3.6.1.4.1.994.3.4.7.21.1 |
pSlot4DescriptionThis field is used in the following card types: discrete-inputs - Description of the alarm point. discrete-outputs - Description of the control point. serial-ports - Description of the serial port. onboard-sensors - Description of the onboard device. analog-Inputs - Description of the analog input device. analog-Sensors - Description of the sensor input device.rw DescriptionString .1.3.6.1.4.1.994.3.4.7.21.1.3 |
pSlot4Desc0This field is used in the following card types: discrete-inputs - Description of the off state. discrete-outputs - Description when the control point is open. onboard-sensors - The description for values between threshold 0 and threshold 1. analog-Inputs - The description for values between threshold 0 and threshold 1. analog-Sensors - The description for values between threshold 0 and threshold 1.rw DescriptionString .1.3.6.1.4.1.994.3.4.7.21.1.4 |
pSlot4Desc1This field is used in the following card types: discrete-inputs - Description of the on state. discrete-outputs - Description when the control point is closed. onboard-sensors - The description for values between threshold 1 and threshold 2. analog-Inputs - The description for values between threshold 1 and threshold 2. analog-Sensors - The description for values between threshold 1 and threshold 2.rw DescriptionString .1.3.6.1.4.1.994.3.4.7.21.1.5 |
pSlot4Desc2This field is used in the following card types: onboard-sensors - The description for values between threshold 2 and threshold 3. analog-Inputs - The description for values between threshold 2 and threshold 3. analog-Sensors - The description for values between threshold 2 and threshold 3.rw DescriptionString .1.3.6.1.4.1.994.3.4.7.21.1.6 |
pSlot4Desc3This field is used in the following card types: onboard-sensors - The description for values between threshold 3 and threshold 4. analog-Inputs - The description for values between threshold 3 and threshold 4. analog-Sensors - The description for values between threshold 3 and threshold 4.rw DescriptionString .1.3.6.1.4.1.994.3.4.7.21.1.7 |
pSlot4Desc4This field is used in the following card types: onboard-sensors - The description for values between threshold 4 and threshold 5. analog-Inputs - The description for values between threshold 4 and threshold 5. analog-Sensors - The description for values between threshold 4 and threshold 5.rw DescriptionString .1.3.6.1.4.1.994.3.4.7.21.1.8 |
pSlot4Desc5This field is used in the following card types: analog-Inputs - Description for a communications failure to the sensor. analog-Sensors - Description for a communications failure to the sensor.rw DescriptionString .1.3.6.1.4.1.994.3.4.7.21.1.9 |
pSlot4ConfiguredThis field is used in the following card types: discrete-inputs - If set to true, changes of state will be reported. If set to false, not change of states will be reported. discrete-outputs - If set to true, the control point will operate. If false, it will not operate. serial-ports - If set to true, this serial port will be usable. If set to false the port will not be usable. onboard-sensors - If set to true, the onboard sensors will be used. If set to false the will be ignored. analog-Inputs - If set to true, the analog inputs will be usable. If set to false the analog inputs will be ignored. analog-Sensors - If set to true, the sensor inputs will be usable. If set to false the sensor inputs will be ignored.rw Configured .1.3.6.1.4.1.994.3.4.7.21.1.10 |
pSlot4SendEmailThis field is used in the following card types: discrete-inputs - If set to true, an email will be sent on a change of state. If false, no email will be sent. onboard-sensors - If set to true an email event will be set when a threshold is crossed. If set to false no email event will be sent. analog-Inputs - If set to true an email event will be set when a threshold is crossed. If set to false no email event will be sent. analog-Sensors - If set to true an email event will be set when a threshold is crossed. If set to false no email event will be sent.rw Boolean .1.3.6.1.4.1.994.3.4.7.21.1.11 |
pSlot4SendSNMPTrapThis field is used in the following card types: discrete-inputs - If set to true, an SNMP trap will be sent on a change of state. If false, no SNMP trap will be sent. onboard-sensors - If set to true an SNMP trap will be set when a threshold is crossed. If set to false no SNMP trap will be sent. analog-Inputs - If set to true an SNMP trap will be set when a threshold is crossed. If set to false no SNMP trap will be sent. analog-Sensors - If set to true an SNMP trap will be set when a threshold is crossed. If set to false no SNMP trap will be sent.rw Boolean .1.3.6.1.4.1.994.3.4.7.21.1.12 |
pSlot4IpAddressThis field is used in the following card types: serial-ports - IP Address of the target device.rw IpAddress .1.3.6.1.4.1.994.3.4.7.21.1.14 |
pSlot4Level0This field is used in the following card types: discrete-inputs - Level of the off state. discrete-outputs - Level of the control point when open. onboard-sensors - The level for values between threshold 0 and threshold 1. analog-Inputs - The level for values between threshold 0 and threshold 1. analog-Sensors - The level for values between threshold 0 and threshold 1.rw Level .1.3.6.1.4.1.994.3.4.7.21.1.17 |
pSlot4Level1This field is used in the following card types: discrete-inputs - Level of the on state. discrete-outputs - Level of the control point when closed. onboard-sensors - The level for values between threshold 1 and threshold 2. analog-Inputs - The level for values between threshold 1 and threshold 2. analog-Sensors - The level for values between threshold 1 and threshold 2.rw Level .1.3.6.1.4.1.994.3.4.7.21.1.18 |
pSlot4Level2This field is used in the following card types: onboard-sensors - The level for values between threshold 2 and threshold 3. analog-Inputs - The level for values between threshold 2 and threshold 3. analog-Sensors - The level for values between threshold 2 and threshold 3.rw Level .1.3.6.1.4.1.994.3.4.7.21.1.19 |
pSlot4Level3This field is used in the following card types: onboard-sensors - The level for values between threshold 3 and threshold 4. analog-Inputs - The level for values between threshold 3 and threshold 4. analog-Sensors - The level for values between threshold 3 and threshold 4.rw Level .1.3.6.1.4.1.994.3.4.7.21.1.20 |
pSlot4Level4This field is used in the following card types: onboard-sensors - The level for values between threshold 4 and threshold 5. analog-Inputs - The level for values between threshold 4 and threshold 5. analog-Sensors - The level for values between threshold 4 and threshold 5.rw Level .1.3.6.1.4.1.994.3.4.7.21.1.21 |
pSlot4Level5This field is used in the following card types: analog-Inputs - Level of a communications failure to the sensor. analog-Sensors - Level of a communications failure to the sensor.rw Level .1.3.6.1.4.1.994.3.4.7.21.1.22 |
pSlot4ReadPeriodThis field is used in the following card types: serial-ports - Inactivity timeout (in minutes).rw Integer32 .1.3.6.1.4.1.994.3.4.7.21.1.23 |
pSlot4Thresh0This field is used in the following card types: onboard-sensors - This is the minimun analog value. analog-Inputs - This is the maximum analog value. analog-Sensors - This is the maximum analog value.ro DescriptionString .1.3.6.1.4.1.994.3.4.7.21.1.28 |
pSlot4Thresh1This field is used in the following card types: onboard-sensors - This is the first threshold value. analog-Inputs - This is the first threshold value. analog-Sensors - This is the first threshold value.rw DescriptionString .1.3.6.1.4.1.994.3.4.7.21.1.29 |
pSlot4Thresh2This field is used in the following card types: onboard-sensors - This is the second threshold value. analog-Inputs - This is the second threshold value. analog-Sensors - This is the second threshold value.rw DescriptionString .1.3.6.1.4.1.994.3.4.7.21.1.30 |
pSlot4Thresh3This field is used in the following card types: onboard-sensors - This is the third threshold value. analog-Inputs - This is the third threshold value. analog-Sensors - This is the third threshold value.rw DescriptionString .1.3.6.1.4.1.994.3.4.7.21.1.31 |
pSlot4Thresh4This field is used in the following card types: onboard-sensors - This is the fourth threshold value. analog-Inputs - This is the fourth threshold value. analog-Sensors - This is the fourth threshold value.rw DescriptionString .1.3.6.1.4.1.994.3.4.7.21.1.32 |
pSlot4Thresh5This field is used in the following card types: onboard-sensors - This is the maximum threshold value. analog-Inputs - This is the minimum threshold value. analog-Sensors - This is the minimum threshold value.ro DescriptionString .1.3.6.1.4.1.994.3.4.7.21.1.33 |
pSlot4ContactStyleThis field is used in the following card types: discrete-inputs - Determines the type of contact.rw ContactStyle .1.3.6.1.4.1.994.3.4.7.21.1.44 |
pSlot4UnitsThis field is used in the following card types: onboard-sensors - Description of the units of measurement. analog-Inputs - Description of the units of measurement. analog-Sensors - Description of the units of measurement.ro DescriptionString .1.3.6.1.4.1.994.3.4.7.21.1.46 |
pSlot4OutputModeThis field is used in the following card types: discrete-outputs - Defines the different ways a control point can be activated.rw OutputMode .1.3.6.1.4.1.994.3.4.7.21.1.47 |
pSlot4OutputStateThis field is used in the following card types: discrete-outputs - A value of 0 will open the control point. A value of 1 will close the control point.rw OutputState .1.3.6.1.4.1.994.3.4.7.21.1.48 |
pSlot4OutputAutoThis field is used in the following card types: discrete-outputs - When this control point is opened, this alarm point will change state to the on state.rw Integer32 .1.3.6.1.4.1.994.3.4.7.21.1.49 |
pSlot4BaudRateThis field is used in the following card types: serial-ports - Baud rate of the serial port.rw BaudRate .1.3.6.1.4.1.994.3.4.7.21.1.57 |
pSlot4DataBitsThis field is used in the following card types: serial-ports - Number of data bit for the serial port.rw DataBits .1.3.6.1.4.1.994.3.4.7.21.1.58 |
pSlot4ParityThis field is used in the following card types: serial-ports - Parity of the serial port.rw Parity .1.3.6.1.4.1.994.3.4.7.21.1.59 |
pSlot4StopBitsThis field is used in the following card types: serial-ports - Number of stop bits for the serial port.rw StopBits .1.3.6.1.4.1.994.3.4.7.21.1.60 |
pSlot4ProtocolThis field is used in the following card types: serial-ports - Protocol the serial port is speaking.rw Protocol .1.3.6.1.4.1.994.3.4.7.21.1.61 |
pSlot4SerialRTSThis field is used in the following card types: serial-ports - Request To Send (RTS) setting for the serial port.rw SerialRTS .1.3.6.1.4.1.994.3.4.7.21.1.62 |
pSlot4SerialCTSThis field is used in the following card types: serial-ports - Clear To Send (CTS) setting for the serial port.rw SerialCTS .1.3.6.1.4.1.994.3.4.7.21.1.63 |
pSlot4LiveDescriptionThis field is used in the following card types: discrete-inputs - The current description of the alarm state. onboard-sensors - The description of the current state of the onboard sensor analog-Inputs - The description of the current state of the analog input. analog-Sensors - The description of the current state of the sensor input.ro DescriptionString .1.3.6.1.4.1.994.3.4.7.21.1.64 |
pSlot4LiveLevelThis field is used in the following card types: discrete-inputs - The current level of the alarm. onboard-sensors - The level of the current state of the onboard sensor. analog-Inputs - The level of the current state of the analog input. analog-Sensors - The level of the current state of the sensor input.ro DescriptionString .1.3.6.1.4.1.994.3.4.7.21.1.65 |
pSlot4LiveRawThis field is used in the following card types: onboard-sensors - The current reading from the onboard sensor. This value will always be between the threshold 0 and threshold 5 values. analog-Inputs - The current reading from the analog input. This value will always be between the threshold 0 and threshold 5 values. analog-Sensors - The current reading from the sensor input. This value will always be between the threshold 0 and threshold 5 values.ro DescriptionString .1.3.6.1.4.1.994.3.4.7.21.1.66 |
pSlot4LiveTimeThis field is used in the following card types: discrete-inputs - The time of the last change of state. onboard-sensors - The time of the last event. analog-Inputs - The time of the last event. analog-Sensors - The time of the last event.ro DescriptionString .1.3.6.1.4.1.994.3.4.7.21.1.67 |
pSlot4PresentThis field is used in the following card types: serial-ports - If set to true, the serial port exists. If set to false the serial port does not exist.ro Boolean .1.3.6.1.4.1.994.3.4.7.21.1.68 |
pSlot4OutputAutoPkgThis field is used in the following card types: discrete-outputs - When this control point is opened, this is the package that the alarm point is located.rw Integer32 .1.3.6.1.4.1.994.3.4.7.21.1.71 |
pSlot4VoltageRangeThis field is used in the following card types: onboard-sensors - The voltage range. analog-Inputs - The voltage range. analog-Sensors - The voltage range.ro VoltageRange .1.3.6.1.4.1.994.3.4.7.21.1.72 |
pSlot4IPPortNumThis field is used in the following card types: serial-ports - IP port number of the target device.rw Integer32 .1.3.6.1.4.1.994.3.4.7.21.1.73 |
pSlot4IOFormatThis field is used in the following card types: discrete-inputs - The io format of discrete inputs. discrete-outputs - The io format of discrete outputs. serial-ports - The io format of serial ports. onboard-sensors - The io format of onboard sensors. analog-Inputs - The io format of analog inputs. analog-Sensors - The io format of analog sensors.ro IOFormat .1.3.6.1.4.1.994.3.4.7.21.1.75 |
pSlot4PortTypeThis field is used in the following card types: serial-ports - The type of serial port.ro PortType .1.3.6.1.4.1.994.3.4.7.21.1.76 |
pSlot4TL1SIDThis field is used in the following card types: discrete-inputs - discrete-outputs - onboard-sensors - analog-Inputs - analog-Sensors -rw DescriptionString .1.3.6.1.4.1.994.3.4.7.21.1.116 |
pSlot4TL1CONDThis field is used in the following card types: discrete-inputs - discrete-outputs - onboard-sensors - analog-Inputs - analog-Sensors -rw DescriptionString .1.3.6.1.4.1.994.3.4.7.21.1.117 |
pSlot4TL1EqptThis field is used in the following card types: discrete-inputs - onboard-sensors - analog-Inputs - analog-Sensors -rw DescriptionString .1.3.6.1.4.1.994.3.4.7.21.1.118 |
pSlot4TL1EnvThis field is used in the following card types: discrete-inputs - onboard-sensors - analog-Inputs - analog-Sensors -rw Boolean .1.3.6.1.4.1.994.3.4.7.21.1.119 |
pSlot4TL1SrveffThis field is used in the following card types: discrete-inputs - onboard-sensors - analog-Inputs - analog-Sensors -rw TL1Srveff .1.3.6.1.4.1.994.3.4.7.21.1.120 |
pSlot4TL1LocnThis field is used in the following card types: discrete-inputs - onboard-sensors - analog-Inputs - analog-Sensors -rw TL1Locn .1.3.6.1.4.1.994.3.4.7.21.1.121 |
pSlot4TL1DirnThis field is used in the following card types: discrete-inputs - onboard-sensors - analog-Inputs - analog-Sensors -rw TL1Dirn .1.3.6.1.4.1.994.3.4.7.21.1.122 |
pSlot4SensorTypeThis field is used in the following card types: analog-Inputs - The type of sensor. analog-Sensors - The type of sensor.rw SensorType .1.3.6.1.4.1.994.3.4.7.21.1.131 |
pSlot4IndexIndex.ro Integer32 .1.3.6.1.4.1.994.3.4.7.21.1.999 |
pSlot5TableTable for configuration of Slot5 SEQUENCE OF PSlot5Entry .1.3.6.1.4.1.994.3.4.7.22 |
pSlot5EntryEntry for configuration table of Slot5 PSlot5Entry .1.3.6.1.4.1.994.3.4.7.22.1 |
pSlot5DescriptionThis field is used in the following card types: discrete-inputs - Description of the alarm point. discrete-outputs - Description of the control point. serial-ports - Description of the serial port. onboard-sensors - Description of the onboard device. analog-Inputs - Description of the analog input device. analog-Sensors - Description of the sensor input device.rw DescriptionString .1.3.6.1.4.1.994.3.4.7.22.1.3 |
pSlot5Desc0This field is used in the following card types: discrete-inputs - Description of the off state. discrete-outputs - Description when the control point is open. onboard-sensors - The description for values between threshold 0 and threshold 1. analog-Inputs - The description for values between threshold 0 and threshold 1. analog-Sensors - The description for values between threshold 0 and threshold 1.rw DescriptionString .1.3.6.1.4.1.994.3.4.7.22.1.4 |
pSlot5Desc1This field is used in the following card types: discrete-inputs - Description of the on state. discrete-outputs - Description when the control point is closed. onboard-sensors - The description for values between threshold 1 and threshold 2. analog-Inputs - The description for values between threshold 1 and threshold 2. analog-Sensors - The description for values between threshold 1 and threshold 2.rw DescriptionString .1.3.6.1.4.1.994.3.4.7.22.1.5 |
pSlot5Desc2This field is used in the following card types: onboard-sensors - The description for values between threshold 2 and threshold 3. analog-Inputs - The description for values between threshold 2 and threshold 3. analog-Sensors - The description for values between threshold 2 and threshold 3.rw DescriptionString .1.3.6.1.4.1.994.3.4.7.22.1.6 |
pSlot5Desc3This field is used in the following card types: onboard-sensors - The description for values between threshold 3 and threshold 4. analog-Inputs - The description for values between threshold 3 and threshold 4. analog-Sensors - The description for values between threshold 3 and threshold 4.rw DescriptionString .1.3.6.1.4.1.994.3.4.7.22.1.7 |
pSlot5Desc4This field is used in the following card types: onboard-sensors - The description for values between threshold 4 and threshold 5. analog-Inputs - The description for values between threshold 4 and threshold 5. analog-Sensors - The description for values between threshold 4 and threshold 5.rw DescriptionString .1.3.6.1.4.1.994.3.4.7.22.1.8 |
pSlot5Desc5This field is used in the following card types: analog-Inputs - Description for a communications failure to the sensor. analog-Sensors - Description for a communications failure to the sensor.rw DescriptionString .1.3.6.1.4.1.994.3.4.7.22.1.9 |
pSlot5ConfiguredThis field is used in the following card types: discrete-inputs - If set to true, changes of state will be reported. If set to false, not change of states will be reported. discrete-outputs - If set to true, the control point will operate. If false, it will not operate. serial-ports - If set to true, this serial port will be usable. If set to false the port will not be usable. onboard-sensors - If set to true, the onboard sensors will be used. If set to false the will be ignored. analog-Inputs - If set to true, the analog inputs will be usable. If set to false the analog inputs will be ignored. analog-Sensors - If set to true, the sensor inputs will be usable. If set to false the sensor inputs will be ignored.rw Configured .1.3.6.1.4.1.994.3.4.7.22.1.10 |
pSlot5SendEmailThis field is used in the following card types: discrete-inputs - If set to true, an email will be sent on a change of state. If false, no email will be sent. onboard-sensors - If set to true an email event will be set when a threshold is crossed. If set to false no email event will be sent. analog-Inputs - If set to true an email event will be set when a threshold is crossed. If set to false no email event will be sent. analog-Sensors - If set to true an email event will be set when a threshold is crossed. If set to false no email event will be sent.rw Boolean .1.3.6.1.4.1.994.3.4.7.22.1.11 |
pSlot5SendSNMPTrapThis field is used in the following card types: discrete-inputs - If set to true, an SNMP trap will be sent on a change of state. If false, no SNMP trap will be sent. onboard-sensors - If set to true an SNMP trap will be set when a threshold is crossed. If set to false no SNMP trap will be sent. analog-Inputs - If set to true an SNMP trap will be set when a threshold is crossed. If set to false no SNMP trap will be sent. analog-Sensors - If set to true an SNMP trap will be set when a threshold is crossed. If set to false no SNMP trap will be sent.rw Boolean .1.3.6.1.4.1.994.3.4.7.22.1.12 |
pSlot5IpAddressThis field is used in the following card types: serial-ports - IP Address of the target device.rw IpAddress .1.3.6.1.4.1.994.3.4.7.22.1.14 |
pSlot5Level0This field is used in the following card types: discrete-inputs - Level of the off state. discrete-outputs - Level of the control point when open. onboard-sensors - The level for values between threshold 0 and threshold 1. analog-Inputs - The level for values between threshold 0 and threshold 1. analog-Sensors - The level for values between threshold 0 and threshold 1.rw Level .1.3.6.1.4.1.994.3.4.7.22.1.17 |
pSlot5Level1This field is used in the following card types: discrete-inputs - Level of the on state. discrete-outputs - Level of the control point when closed. onboard-sensors - The level for values between threshold 1 and threshold 2. analog-Inputs - The level for values between threshold 1 and threshold 2. analog-Sensors - The level for values between threshold 1 and threshold 2.rw Level .1.3.6.1.4.1.994.3.4.7.22.1.18 |
pSlot5Level2This field is used in the following card types: onboard-sensors - The level for values between threshold 2 and threshold 3. analog-Inputs - The level for values between threshold 2 and threshold 3. analog-Sensors - The level for values between threshold 2 and threshold 3.rw Level .1.3.6.1.4.1.994.3.4.7.22.1.19 |
pSlot5Level3This field is used in the following card types: onboard-sensors - The level for values between threshold 3 and threshold 4. analog-Inputs - The level for values between threshold 3 and threshold 4. analog-Sensors - The level for values between threshold 3 and threshold 4.rw Level .1.3.6.1.4.1.994.3.4.7.22.1.20 |
pSlot5Level4This field is used in the following card types: onboard-sensors - The level for values between threshold 4 and threshold 5. analog-Inputs - The level for values between threshold 4 and threshold 5. analog-Sensors - The level for values between threshold 4 and threshold 5.rw Level .1.3.6.1.4.1.994.3.4.7.22.1.21 |
pSlot5Level5This field is used in the following card types: analog-Inputs - Level of a communications failure to the sensor. analog-Sensors - Level of a communications failure to the sensor.rw Level .1.3.6.1.4.1.994.3.4.7.22.1.22 |
pSlot5ReadPeriodThis field is used in the following card types: serial-ports - Inactivity timeout (in minutes).rw Integer32 .1.3.6.1.4.1.994.3.4.7.22.1.23 |
pSlot5Thresh0This field is used in the following card types: onboard-sensors - This is the minimun analog value. analog-Inputs - This is the maximum analog value. analog-Sensors - This is the maximum analog value.ro DescriptionString .1.3.6.1.4.1.994.3.4.7.22.1.28 |
pSlot5Thresh1This field is used in the following card types: onboard-sensors - This is the first threshold value. analog-Inputs - This is the first threshold value. analog-Sensors - This is the first threshold value.rw DescriptionString .1.3.6.1.4.1.994.3.4.7.22.1.29 |
pSlot5Thresh2This field is used in the following card types: onboard-sensors - This is the second threshold value. analog-Inputs - This is the second threshold value. analog-Sensors - This is the second threshold value.rw DescriptionString .1.3.6.1.4.1.994.3.4.7.22.1.30 |
pSlot5Thresh3This field is used in the following card types: onboard-sensors - This is the third threshold value. analog-Inputs - This is the third threshold value. analog-Sensors - This is the third threshold value.rw DescriptionString .1.3.6.1.4.1.994.3.4.7.22.1.31 |
pSlot5Thresh4This field is used in the following card types: onboard-sensors - This is the fourth threshold value. analog-Inputs - This is the fourth threshold value. analog-Sensors - This is the fourth threshold value.rw DescriptionString .1.3.6.1.4.1.994.3.4.7.22.1.32 |
pSlot5Thresh5This field is used in the following card types: onboard-sensors - This is the maximum threshold value. analog-Inputs - This is the minimum threshold value. analog-Sensors - This is the minimum threshold value.ro DescriptionString .1.3.6.1.4.1.994.3.4.7.22.1.33 |
pSlot5ContactStyleThis field is used in the following card types: discrete-inputs - Determines the type of contact.rw ContactStyle .1.3.6.1.4.1.994.3.4.7.22.1.44 |
pSlot5UnitsThis field is used in the following card types: onboard-sensors - Description of the units of measurement. analog-Inputs - Description of the units of measurement. analog-Sensors - Description of the units of measurement.ro DescriptionString .1.3.6.1.4.1.994.3.4.7.22.1.46 |
pSlot5OutputModeThis field is used in the following card types: discrete-outputs - Defines the different ways a control point can be activated.rw OutputMode .1.3.6.1.4.1.994.3.4.7.22.1.47 |
pSlot5OutputStateThis field is used in the following card types: discrete-outputs - A value of 0 will open the control point. A value of 1 will close the control point.rw OutputState .1.3.6.1.4.1.994.3.4.7.22.1.48 |
pSlot5OutputAutoThis field is used in the following card types: discrete-outputs - When this control point is opened, this alarm point will change state to the on state.rw Integer32 .1.3.6.1.4.1.994.3.4.7.22.1.49 |
pSlot5BaudRateThis field is used in the following card types: serial-ports - Baud rate of the serial port.rw BaudRate .1.3.6.1.4.1.994.3.4.7.22.1.57 |
pSlot5DataBitsThis field is used in the following card types: serial-ports - Number of data bit for the serial port.rw DataBits .1.3.6.1.4.1.994.3.4.7.22.1.58 |
pSlot5ParityThis field is used in the following card types: serial-ports - Parity of the serial port.rw Parity .1.3.6.1.4.1.994.3.4.7.22.1.59 |
pSlot5StopBitsThis field is used in the following card types: serial-ports - Number of stop bits for the serial port.rw StopBits .1.3.6.1.4.1.994.3.4.7.22.1.60 |
pSlot5ProtocolThis field is used in the following card types: serial-ports - Protocol the serial port is speaking.rw Protocol .1.3.6.1.4.1.994.3.4.7.22.1.61 |
pSlot5SerialRTSThis field is used in the following card types: serial-ports - Request To Send (RTS) setting for the serial port.rw SerialRTS .1.3.6.1.4.1.994.3.4.7.22.1.62 |
pSlot5SerialCTSThis field is used in the following card types: serial-ports - Clear To Send (CTS) setting for the serial port.rw SerialCTS .1.3.6.1.4.1.994.3.4.7.22.1.63 |
pSlot5LiveDescriptionThis field is used in the following card types: discrete-inputs - The current description of the alarm state. onboard-sensors - The description of the current state of the onboard sensor analog-Inputs - The description of the current state of the analog input. analog-Sensors - The description of the current state of the sensor input.ro DescriptionString .1.3.6.1.4.1.994.3.4.7.22.1.64 |
pSlot5LiveLevelThis field is used in the following card types: discrete-inputs - The current level of the alarm. onboard-sensors - The level of the current state of the onboard sensor. analog-Inputs - The level of the current state of the analog input. analog-Sensors - The level of the current state of the sensor input.ro DescriptionString .1.3.6.1.4.1.994.3.4.7.22.1.65 |
pSlot5LiveRawThis field is used in the following card types: onboard-sensors - The current reading from the onboard sensor. This value will always be between the threshold 0 and threshold 5 values. analog-Inputs - The current reading from the analog input. This value will always be between the threshold 0 and threshold 5 values. analog-Sensors - The current reading from the sensor input. This value will always be between the threshold 0 and threshold 5 values.ro DescriptionString .1.3.6.1.4.1.994.3.4.7.22.1.66 |
pSlot5LiveTimeThis field is used in the following card types: discrete-inputs - The time of the last change of state. onboard-sensors - The time of the last event. analog-Inputs - The time of the last event. analog-Sensors - The time of the last event.ro DescriptionString .1.3.6.1.4.1.994.3.4.7.22.1.67 |
pSlot5PresentThis field is used in the following card types: serial-ports - If set to true, the serial port exists. If set to false the serial port does not exist.ro Boolean .1.3.6.1.4.1.994.3.4.7.22.1.68 |
pSlot5OutputAutoPkgThis field is used in the following card types: discrete-outputs - When this control point is opened, this is the package that the alarm point is located.rw Integer32 .1.3.6.1.4.1.994.3.4.7.22.1.71 |
pSlot5VoltageRangeThis field is used in the following card types: onboard-sensors - The voltage range. analog-Inputs - The voltage range. analog-Sensors - The voltage range.ro VoltageRange .1.3.6.1.4.1.994.3.4.7.22.1.72 |
pSlot5IPPortNumThis field is used in the following card types: serial-ports - IP port number of the target device.rw Integer32 .1.3.6.1.4.1.994.3.4.7.22.1.73 |
pSlot5IOFormatThis field is used in the following card types: discrete-inputs - The io format of discrete inputs. discrete-outputs - The io format of discrete outputs. serial-ports - The io format of serial ports. onboard-sensors - The io format of onboard sensors. analog-Inputs - The io format of analog inputs. analog-Sensors - The io format of analog sensors.ro IOFormat .1.3.6.1.4.1.994.3.4.7.22.1.75 |
pSlot5PortTypeThis field is used in the following card types: serial-ports - The type of serial port.ro PortType .1.3.6.1.4.1.994.3.4.7.22.1.76 |
pSlot5TL1SIDThis field is used in the following card types: discrete-inputs - discrete-outputs - onboard-sensors - analog-Inputs - analog-Sensors -rw DescriptionString .1.3.6.1.4.1.994.3.4.7.22.1.116 |
pSlot5TL1CONDThis field is used in the following card types: discrete-inputs - discrete-outputs - onboard-sensors - analog-Inputs - analog-Sensors -rw DescriptionString .1.3.6.1.4.1.994.3.4.7.22.1.117 |
pSlot5TL1EqptThis field is used in the following card types: discrete-inputs - onboard-sensors - analog-Inputs - analog-Sensors -rw DescriptionString .1.3.6.1.4.1.994.3.4.7.22.1.118 |
pSlot5TL1EnvThis field is used in the following card types: discrete-inputs - onboard-sensors - analog-Inputs - analog-Sensors -rw Boolean .1.3.6.1.4.1.994.3.4.7.22.1.119 |
pSlot5TL1SrveffThis field is used in the following card types: discrete-inputs - onboard-sensors - analog-Inputs - analog-Sensors -rw TL1Srveff .1.3.6.1.4.1.994.3.4.7.22.1.120 |
pSlot5TL1LocnThis field is used in the following card types: discrete-inputs - onboard-sensors - analog-Inputs - analog-Sensors -rw TL1Locn .1.3.6.1.4.1.994.3.4.7.22.1.121 |
pSlot5TL1DirnThis field is used in the following card types: discrete-inputs - onboard-sensors - analog-Inputs - analog-Sensors -rw TL1Dirn .1.3.6.1.4.1.994.3.4.7.22.1.122 |
pSlot5SensorTypeThis field is used in the following card types: analog-Inputs - The type of sensor. analog-Sensors - The type of sensor.rw SensorType .1.3.6.1.4.1.994.3.4.7.22.1.131 |
pSlot5IndexIndex.ro Integer32 .1.3.6.1.4.1.994.3.4.7.22.1.999 |
pSlot6TableTable for configuration of Slot6 SEQUENCE OF PSlot6Entry .1.3.6.1.4.1.994.3.4.7.23 |
pSlot6EntryEntry for configuration table of Slot6 PSlot6Entry .1.3.6.1.4.1.994.3.4.7.23.1 |
pSlot6DescriptionThis field is used in the following card types: discrete-inputs - Description of the alarm point. discrete-outputs - Description of the control point. serial-ports - Description of the serial port. onboard-sensors - Description of the onboard device. analog-Inputs - Description of the analog input device. analog-Sensors - Description of the sensor input device.rw DescriptionString .1.3.6.1.4.1.994.3.4.7.23.1.3 |
pSlot6Desc0This field is used in the following card types: discrete-inputs - Description of the off state. discrete-outputs - Description when the control point is open. onboard-sensors - The description for values between threshold 0 and threshold 1. analog-Inputs - The description for values between threshold 0 and threshold 1. analog-Sensors - The description for values between threshold 0 and threshold 1.rw DescriptionString .1.3.6.1.4.1.994.3.4.7.23.1.4 |
pSlot6Desc1This field is used in the following card types: discrete-inputs - Description of the on state. discrete-outputs - Description when the control point is closed. onboard-sensors - The description for values between threshold 1 and threshold 2. analog-Inputs - The description for values between threshold 1 and threshold 2. analog-Sensors - The description for values between threshold 1 and threshold 2.rw DescriptionString .1.3.6.1.4.1.994.3.4.7.23.1.5 |
pSlot6Desc2This field is used in the following card types: onboard-sensors - The description for values between threshold 2 and threshold 3. analog-Inputs - The description for values between threshold 2 and threshold 3. analog-Sensors - The description for values between threshold 2 and threshold 3.rw DescriptionString .1.3.6.1.4.1.994.3.4.7.23.1.6 |
pSlot6Desc3This field is used in the following card types: onboard-sensors - The description for values between threshold 3 and threshold 4. analog-Inputs - The description for values between threshold 3 and threshold 4. analog-Sensors - The description for values between threshold 3 and threshold 4.rw DescriptionString .1.3.6.1.4.1.994.3.4.7.23.1.7 |
pSlot6Desc4This field is used in the following card types: onboard-sensors - The description for values between threshold 4 and threshold 5. analog-Inputs - The description for values between threshold 4 and threshold 5. analog-Sensors - The description for values between threshold 4 and threshold 5.rw DescriptionString .1.3.6.1.4.1.994.3.4.7.23.1.8 |
pSlot6Desc5This field is used in the following card types: analog-Inputs - Description for a communications failure to the sensor. analog-Sensors - Description for a communications failure to the sensor.rw DescriptionString .1.3.6.1.4.1.994.3.4.7.23.1.9 |
pSlot6ConfiguredThis field is used in the following card types: discrete-inputs - If set to true, changes of state will be reported. If set to false, not change of states will be reported. discrete-outputs - If set to true, the control point will operate. If false, it will not operate. serial-ports - If set to true, this serial port will be usable. If set to false the port will not be usable. onboard-sensors - If set to true, the onboard sensors will be used. If set to false the will be ignored. analog-Inputs - If set to true, the analog inputs will be usable. If set to false the analog inputs will be ignored. analog-Sensors - If set to true, the sensor inputs will be usable. If set to false the sensor inputs will be ignored.rw Configured .1.3.6.1.4.1.994.3.4.7.23.1.10 |
pSlot6SendEmailThis field is used in the following card types: discrete-inputs - If set to true, an email will be sent on a change of state. If false, no email will be sent. onboard-sensors - If set to true an email event will be set when a threshold is crossed. If set to false no email event will be sent. analog-Inputs - If set to true an email event will be set when a threshold is crossed. If set to false no email event will be sent. analog-Sensors - If set to true an email event will be set when a threshold is crossed. If set to false no email event will be sent.rw Boolean .1.3.6.1.4.1.994.3.4.7.23.1.11 |
pSlot6SendSNMPTrapThis field is used in the following card types: discrete-inputs - If set to true, an SNMP trap will be sent on a change of state. If false, no SNMP trap will be sent. onboard-sensors - If set to true an SNMP trap will be set when a threshold is crossed. If set to false no SNMP trap will be sent. analog-Inputs - If set to true an SNMP trap will be set when a threshold is crossed. If set to false no SNMP trap will be sent. analog-Sensors - If set to true an SNMP trap will be set when a threshold is crossed. If set to false no SNMP trap will be sent.rw Boolean .1.3.6.1.4.1.994.3.4.7.23.1.12 |
pSlot6IpAddressThis field is used in the following card types: serial-ports - IP Address of the target device.rw IpAddress .1.3.6.1.4.1.994.3.4.7.23.1.14 |
pSlot6Level0This field is used in the following card types: discrete-inputs - Level of the off state. discrete-outputs - Level of the control point when open. onboard-sensors - The level for values between threshold 0 and threshold 1. analog-Inputs - The level for values between threshold 0 and threshold 1. analog-Sensors - The level for values between threshold 0 and threshold 1.rw Level .1.3.6.1.4.1.994.3.4.7.23.1.17 |
pSlot6Level1This field is used in the following card types: discrete-inputs - Level of the on state. discrete-outputs - Level of the control point when closed. onboard-sensors - The level for values between threshold 1 and threshold 2. analog-Inputs - The level for values between threshold 1 and threshold 2. analog-Sensors - The level for values between threshold 1 and threshold 2.rw Level .1.3.6.1.4.1.994.3.4.7.23.1.18 |
pSlot6Level2This field is used in the following card types: onboard-sensors - The level for values between threshold 2 and threshold 3. analog-Inputs - The level for values between threshold 2 and threshold 3. analog-Sensors - The level for values between threshold 2 and threshold 3.rw Level .1.3.6.1.4.1.994.3.4.7.23.1.19 |
pSlot6Level3This field is used in the following card types: onboard-sensors - The level for values between threshold 3 and threshold 4. analog-Inputs - The level for values between threshold 3 and threshold 4. analog-Sensors - The level for values between threshold 3 and threshold 4.rw Level .1.3.6.1.4.1.994.3.4.7.23.1.20 |
pSlot6Level4This field is used in the following card types: onboard-sensors - The level for values between threshold 4 and threshold 5. analog-Inputs - The level for values between threshold 4 and threshold 5. analog-Sensors - The level for values between threshold 4 and threshold 5.rw Level .1.3.6.1.4.1.994.3.4.7.23.1.21 |
pSlot6Level5This field is used in the following card types: analog-Inputs - Level of a communications failure to the sensor. analog-Sensors - Level of a communications failure to the sensor.rw Level .1.3.6.1.4.1.994.3.4.7.23.1.22 |
pSlot6ReadPeriodThis field is used in the following card types: serial-ports - Inactivity timeout (in minutes).rw Integer32 .1.3.6.1.4.1.994.3.4.7.23.1.23 |
pSlot6Thresh0This field is used in the following card types: onboard-sensors - This is the minimun analog value. analog-Inputs - This is the maximum analog value. analog-Sensors - This is the maximum analog value.ro DescriptionString .1.3.6.1.4.1.994.3.4.7.23.1.28 |
pSlot6Thresh1This field is used in the following card types: onboard-sensors - This is the first threshold value. analog-Inputs - This is the first threshold value. analog-Sensors - This is the first threshold value.rw DescriptionString .1.3.6.1.4.1.994.3.4.7.23.1.29 |
pSlot6Thresh2This field is used in the following card types: onboard-sensors - This is the second threshold value. analog-Inputs - This is the second threshold value. analog-Sensors - This is the second threshold value.rw DescriptionString .1.3.6.1.4.1.994.3.4.7.23.1.30 |
pSlot6Thresh3This field is used in the following card types: onboard-sensors - This is the third threshold value. analog-Inputs - This is the third threshold value. analog-Sensors - This is the third threshold value.rw DescriptionString .1.3.6.1.4.1.994.3.4.7.23.1.31 |
pSlot6Thresh4This field is used in the following card types: onboard-sensors - This is the fourth threshold value. analog-Inputs - This is the fourth threshold value. analog-Sensors - This is the fourth threshold value.rw DescriptionString .1.3.6.1.4.1.994.3.4.7.23.1.32 |
pSlot6Thresh5This field is used in the following card types: onboard-sensors - This is the maximum threshold value. analog-Inputs - This is the minimum threshold value. analog-Sensors - This is the minimum threshold value.ro DescriptionString .1.3.6.1.4.1.994.3.4.7.23.1.33 |
pSlot6ContactStyleThis field is used in the following card types: discrete-inputs - Determines the type of contact.rw ContactStyle .1.3.6.1.4.1.994.3.4.7.23.1.44 |
pSlot6UnitsThis field is used in the following card types: onboard-sensors - Description of the units of measurement. analog-Inputs - Description of the units of measurement. analog-Sensors - Description of the units of measurement.ro DescriptionString .1.3.6.1.4.1.994.3.4.7.23.1.46 |
pSlot6OutputModeThis field is used in the following card types: discrete-outputs - Defines the different ways a control point can be activated.rw OutputMode .1.3.6.1.4.1.994.3.4.7.23.1.47 |
pSlot6OutputStateThis field is used in the following card types: discrete-outputs - A value of 0 will open the control point. A value of 1 will close the control point.rw OutputState .1.3.6.1.4.1.994.3.4.7.23.1.48 |
pSlot6OutputAutoThis field is used in the following card types: discrete-outputs - When this control point is opened, this alarm point will change state to the on state.rw Integer32 .1.3.6.1.4.1.994.3.4.7.23.1.49 |
pSlot6BaudRateThis field is used in the following card types: serial-ports - Baud rate of the serial port.rw BaudRate .1.3.6.1.4.1.994.3.4.7.23.1.57 |
pSlot6DataBitsThis field is used in the following card types: serial-ports - Number of data bit for the serial port.rw DataBits .1.3.6.1.4.1.994.3.4.7.23.1.58 |
pSlot6ParityThis field is used in the following card types: serial-ports - Parity of the serial port.rw Parity .1.3.6.1.4.1.994.3.4.7.23.1.59 |
pSlot6StopBitsThis field is used in the following card types: serial-ports - Number of stop bits for the serial port.rw StopBits .1.3.6.1.4.1.994.3.4.7.23.1.60 |
pSlot6ProtocolThis field is used in the following card types: serial-ports - Protocol the serial port is speaking.rw Protocol .1.3.6.1.4.1.994.3.4.7.23.1.61 |
pSlot6SerialRTSThis field is used in the following card types: serial-ports - Request To Send (RTS) setting for the serial port.rw SerialRTS .1.3.6.1.4.1.994.3.4.7.23.1.62 |
pSlot6SerialCTSThis field is used in the following card types: serial-ports - Clear To Send (CTS) setting for the serial port.rw SerialCTS .1.3.6.1.4.1.994.3.4.7.23.1.63 |
pSlot6LiveDescriptionThis field is used in the following card types: discrete-inputs - The current description of the alarm state. onboard-sensors - The description of the current state of the onboard sensor analog-Inputs - The description of the current state of the analog input. analog-Sensors - The description of the current state of the sensor input.ro DescriptionString .1.3.6.1.4.1.994.3.4.7.23.1.64 |
pSlot6LiveLevelThis field is used in the following card types: discrete-inputs - The current level of the alarm. onboard-sensors - The level of the current state of the onboard sensor. analog-Inputs - The level of the current state of the analog input. analog-Sensors - The level of the current state of the sensor input.ro DescriptionString .1.3.6.1.4.1.994.3.4.7.23.1.65 |
pSlot6LiveRawThis field is used in the following card types: onboard-sensors - The current reading from the onboard sensor. This value will always be between the threshold 0 and threshold 5 values. analog-Inputs - The current reading from the analog input. This value will always be between the threshold 0 and threshold 5 values. analog-Sensors - The current reading from the sensor input. This value will always be between the threshold 0 and threshold 5 values.ro DescriptionString .1.3.6.1.4.1.994.3.4.7.23.1.66 |
pSlot6LiveTimeThis field is used in the following card types: discrete-inputs - The time of the last change of state. onboard-sensors - The time of the last event. analog-Inputs - The time of the last event. analog-Sensors - The time of the last event.ro DescriptionString .1.3.6.1.4.1.994.3.4.7.23.1.67 |
pSlot6PresentThis field is used in the following card types: serial-ports - If set to true, the serial port exists. If set to false the serial port does not exist.ro Boolean .1.3.6.1.4.1.994.3.4.7.23.1.68 |
pSlot6OutputAutoPkgThis field is used in the following card types: discrete-outputs - When this control point is opened, this is the package that the alarm point is located.rw Integer32 .1.3.6.1.4.1.994.3.4.7.23.1.71 |
pSlot6VoltageRangeThis field is used in the following card types: onboard-sensors - The voltage range. analog-Inputs - The voltage range. analog-Sensors - The voltage range.ro VoltageRange .1.3.6.1.4.1.994.3.4.7.23.1.72 |
pSlot6IPPortNumThis field is used in the following card types: serial-ports - IP port number of the target device.rw Integer32 .1.3.6.1.4.1.994.3.4.7.23.1.73 |
pSlot6IOFormatThis field is used in the following card types: discrete-inputs - The io format of discrete inputs. discrete-outputs - The io format of discrete outputs. serial-ports - The io format of serial ports. onboard-sensors - The io format of onboard sensors. analog-Inputs - The io format of analog inputs. analog-Sensors - The io format of analog sensors.ro IOFormat .1.3.6.1.4.1.994.3.4.7.23.1.75 |
pSlot6PortTypeThis field is used in the following card types: serial-ports - The type of serial port.ro PortType .1.3.6.1.4.1.994.3.4.7.23.1.76 |
pSlot6TL1SIDThis field is used in the following card types: discrete-inputs - discrete-outputs - onboard-sensors - analog-Inputs - analog-Sensors -rw DescriptionString .1.3.6.1.4.1.994.3.4.7.23.1.116 |
pSlot6TL1CONDThis field is used in the following card types: discrete-inputs - discrete-outputs - onboard-sensors - analog-Inputs - analog-Sensors -rw DescriptionString .1.3.6.1.4.1.994.3.4.7.23.1.117 |
pSlot6TL1EqptThis field is used in the following card types: discrete-inputs - onboard-sensors - analog-Inputs - analog-Sensors -rw DescriptionString .1.3.6.1.4.1.994.3.4.7.23.1.118 |
pSlot6TL1EnvThis field is used in the following card types: discrete-inputs - onboard-sensors - analog-Inputs - analog-Sensors -rw Boolean .1.3.6.1.4.1.994.3.4.7.23.1.119 |
pSlot6TL1SrveffThis field is used in the following card types: discrete-inputs - onboard-sensors - analog-Inputs - analog-Sensors -rw TL1Srveff .1.3.6.1.4.1.994.3.4.7.23.1.120 |
pSlot6TL1LocnThis field is used in the following card types: discrete-inputs - onboard-sensors - analog-Inputs - analog-Sensors -rw TL1Locn .1.3.6.1.4.1.994.3.4.7.23.1.121 |
pSlot6TL1DirnThis field is used in the following card types: discrete-inputs - onboard-sensors - analog-Inputs - analog-Sensors -rw TL1Dirn .1.3.6.1.4.1.994.3.4.7.23.1.122 |
pSlot6SensorTypeThis field is used in the following card types: analog-Inputs - The type of sensor. analog-Sensors - The type of sensor.rw SensorType .1.3.6.1.4.1.994.3.4.7.23.1.131 |
pSlot6IndexIndex.ro Integer32 .1.3.6.1.4.1.994.3.4.7.23.1.999 |
pNetPortsTableTable for configuration of NetPorts SEQUENCE OF PNetPortsEntry .1.3.6.1.4.1.994.3.4.7.24 |
pNetPortsEntryEntry for configuration table of NetPorts PNetPortsEntry .1.3.6.1.4.1.994.3.4.7.24.1 |
pNetPortsDescriptionDescription of the static network ports.ro DescriptionString .1.3.6.1.4.1.994.3.4.7.24.1.3 |
pNetPortsIPPortNumIP port number to use when connecting to this network port.rw Integer32 .1.3.6.1.4.1.994.3.4.7.24.1.73 |
pNetPortsIndexIndex.ro Integer32 .1.3.6.1.4.1.994.3.4.7.24.1.999 |
wirelessModem OBJECT IDENTIFIER .1.3.6.1.4.1.994.3.4.7.25 |
wirelessModemBackupIPAddressWireless Modem IP Address.ro IpAddress .1.3.6.1.4.1.994.3.4.7.25.78 |
wirelessModemTimeWireless modem 24 hour reset time (hh:mm:ss)rw DescriptionString .1.3.6.1.4.1.994.3.4.7.25.81 |
wirelessModemTransmitThe string that will be sent to the modem.rw DescriptionString .1.3.6.1.4.1.994.3.4.7.25.96 |
wirelessModemUseWirelessNetworkDetermines if modem tries to connect to wireless network.rw Boolean .1.3.6.1.4.1.994.3.4.7.25.97 |
wirelessModemUseResetTimeDetermines if the modem resets at reset time.rw Boolean .1.3.6.1.4.1.994.3.4.7.25.98 |
wirelessModemResponseWaitTimeResponse Timeout (s)rw DescriptionString .1.3.6.1.4.1.994.3.4.7.25.99 |
wirelessModemSecondaryDetermines if the modem can use accept a dynamic (local) IP.rw Boolean .1.3.6.1.4.1.994.3.4.7.25.115 |
webmonSecurity OBJECT IDENTIFIER .1.3.6.1.4.1.994.3.4.7.26 |
webmonSecurityUserLevelThis is the default user level. Anyone who has access to this device will have these permissions without logging in. One of the following masks from each group are used: No FTP access 0x0000 0 FTP read-only 0x0001 1 FTP Full access 0x0003 3 No Web access 0x0000 0 Monitor 0x0010 16 Config 0x0030 48 Config + Accounts 0x00B0 176 The masks are added together to create a permission value.rw Unsigned32 .1.3.6.1.4.1.994.3.4.7.26.55 |
webmonSecurityUnsecuredAllow unsecured configuration for SNMP.rw Boolean .1.3.6.1.4.1.994.3.4.7.26.77 |
dateTime OBJECT IDENTIFIER .1.3.6.1.4.1.994.3.4.7.27 |
dateTimeConfiguredDetermines whether or not NTP will be used to set system time.rw Configured .1.3.6.1.4.1.994.3.4.7.27.10 |
dateTimeIpAddressTime Server IP Addressrw IpAddress .1.3.6.1.4.1.994.3.4.7.27.14 |
dateTimeDaylightSavingDetermines if Daylight Savings is automatically adjusted.rw Boolean .1.3.6.1.4.1.994.3.4.7.27.53 |
dateTimeDateThis is the system date.rw DescriptionString .1.3.6.1.4.1.994.3.4.7.27.80 |
dateTimeTimeThis is the system time.rw DescriptionString .1.3.6.1.4.1.994.3.4.7.27.81 |
dateTimeNegOffsetTrue if a negative offset from UTC is desiredrw Boolean .1.3.6.1.4.1.994.3.4.7.27.88 |
dateTimeUTCOffsetTime offset of local time compared to UTCrw DescriptionString .1.3.6.1.4.1.994.3.4.7.27.89 |
pDCMProtocolTableTable for configuration of DCMProtocol SEQUENCE OF PDCMProtocolEntry .1.3.6.1.4.1.994.3.4.7.28 |
pDCMProtocolEntryEntry for configuration table of DCMProtocol PDCMProtocolEntry .1.3.6.1.4.1.994.3.4.7.28.1 |
pDCMProtocolDescriptionDescription of the input device that DCM will poll.ro DescriptionString .1.3.6.1.4.1.994.3.4.7.28.1.3 |
pDCMProtocolConfiguredIf set to true, this input will be polled in DCM. If set to false, it will not be polled.rw Configured .1.3.6.1.4.1.994.3.4.7.28.1.10 |
pDCMProtocolBaseDCMAddressBase DCM address for this input device.rw Integer32 .1.3.6.1.4.1.994.3.4.7.28.1.83 |
pDCMProtocolIndexIndex.ro Integer32 .1.3.6.1.4.1.994.3.4.7.28.1.999 |
pdialOutTableTable for configuration of dialOut SEQUENCE OF PdialOutEntry .1.3.6.1.4.1.994.3.4.7.29 |
pdialOutEntryEntry for configuration table of dialOut PdialOutEntry .1.3.6.1.4.1.994.3.4.7.29.1 |
pdialOutConfiguredDetermines whether or not dial ou will be used to send SNMP traps.rw Configured .1.3.6.1.4.1.994.3.4.7.29.1.10 |
pdialOutNameDial out Usernamerw DescriptionString .1.3.6.1.4.1.994.3.4.7.29.1.25 |
pdialOutPasswordPassword to use when dialing outrw DescriptionString .1.3.6.1.4.1.994.3.4.7.29.1.26 |
pdialOutDialOutNumberNumber to dial for dial outrw DescriptionString .1.3.6.1.4.1.994.3.4.7.29.1.79 |
pdialOutIndexIndex.ro Integer32 .1.3.6.1.4.1.994.3.4.7.29.1.999 |
pderivedDiscreteTableTable for configuration of derivedDiscrete SEQUENCE OF PderivedDiscreteEntry .1.3.6.1.4.1.994.3.4.7.30 |
pderivedDiscreteEntryEntry for configuration table of derivedDiscrete PderivedDiscreteEntry .1.3.6.1.4.1.994.3.4.7.30.1 |
pderivedDiscreteDescriptionDescription of the derived alarm point.rw DescriptionString .1.3.6.1.4.1.994.3.4.7.30.1.3 |
pderivedDiscreteDesc0Description of the off state.rw DescriptionString .1.3.6.1.4.1.994.3.4.7.30.1.4 |
pderivedDiscreteDesc1Description of the on state.rw DescriptionString .1.3.6.1.4.1.994.3.4.7.30.1.5 |
pderivedDiscreteConfiguredIf set to true, changes of state will be reported. If set to false, not change of states will be reported.rw Configured .1.3.6.1.4.1.994.3.4.7.30.1.10 |
pderivedDiscreteSendEmailIf set to true, an email will be sent on a change of state. If false, no email will be sent.rw Boolean .1.3.6.1.4.1.994.3.4.7.30.1.11 |
pderivedDiscreteSendSNMPTrapIf set to true, an SNMP trap will be sent on a change of state. If false, no SNMP trap will be sent.rw Boolean .1.3.6.1.4.1.994.3.4.7.30.1.12 |
pderivedDiscreteLevel0Level of the off state.rw Level .1.3.6.1.4.1.994.3.4.7.30.1.17 |
pderivedDiscreteLevel1Level of the on state.rw Level .1.3.6.1.4.1.994.3.4.7.30.1.18 |
pderivedDiscreteLiveDescriptionThe current description of the alarm state.ro DescriptionString .1.3.6.1.4.1.994.3.4.7.30.1.64 |
pderivedDiscreteLiveLevelThe current level of the alarm.ro DescriptionString .1.3.6.1.4.1.994.3.4.7.30.1.65 |
pderivedDiscreteLiveTimeThe time of the last change of state.ro DescriptionString .1.3.6.1.4.1.994.3.4.7.30.1.67 |
pderivedDiscreteElementAPkgPackage where the alarm point is located for element A.rw Integer32 .1.3.6.1.4.1.994.3.4.7.30.1.90 |
pderivedDiscreteElementAPointAlarm point for element A.rw Integer32 .1.3.6.1.4.1.994.3.4.7.30.1.91 |
pderivedDiscreteElementBPkgPackage where the alarm point is located for element B.rw Integer32 .1.3.6.1.4.1.994.3.4.7.30.1.92 |
pderivedDiscreteElementBPointAlarm point for element B.rw Integer32 .1.3.6.1.4.1.994.3.4.7.30.1.93 |
pderivedDiscreteDiscreteFormulaThe formula that will be used to compute the derived alarm.rw DiscreteFormula .1.3.6.1.4.1.994.3.4.7.30.1.94 |
pderivedDiscreteTL1SID(TL1) System ID associated with this item.rw DescriptionString .1.3.6.1.4.1.994.3.4.7.30.1.116 |
pderivedDiscreteTL1COND(TL1) Condition text associated with this item.rw DescriptionString .1.3.6.1.4.1.994.3.4.7.30.1.117 |
pderivedDiscreteTL1Eqpt(TL1) EQPT field associated with this item.rw DescriptionString .1.3.6.1.4.1.994.3.4.7.30.1.118 |
pderivedDiscreteTL1Env(TL1) Environmental field associated with this item.rw Boolean .1.3.6.1.4.1.994.3.4.7.30.1.119 |
pderivedDiscreteTL1Srveff(TL1) Service Effecting field associated with this item.rw TL1Srveff .1.3.6.1.4.1.994.3.4.7.30.1.120 |
pderivedDiscreteTL1Locn(TL1) Location field associated with this item.rw TL1Locn .1.3.6.1.4.1.994.3.4.7.30.1.121 |
pderivedDiscreteTL1Dirn(TL1) Direction field associated with this item.rw TL1Dirn .1.3.6.1.4.1.994.3.4.7.30.1.122 |
pderivedDiscreteIndexIndex.ro Integer32 .1.3.6.1.4.1.994.3.4.7.30.1.999 |
license OBJECT IDENTIFIER .1.3.6.1.4.1.994.3.4.7.31 |
licenseDescriptionThis describes the status of the licensero DescriptionString .1.3.6.1.4.1.994.3.4.7.31.3 |
licenseLicenseKeyThis is the License Key.rw DescriptionString .1.3.6.1.4.1.994.3.4.7.31.84 |
licenseExpiresThis is the date the current License will expire.ro DescriptionString .1.3.6.1.4.1.994.3.4.7.31.85 |
licenseAllowTL1This describes the status of TL1 support in the licensero Boolean .1.3.6.1.4.1.994.3.4.7.31.124 |
pe2aHostTableTable for configuration of e2aHost SEQUENCE OF Pe2aHostEntry .1.3.6.1.4.1.994.3.4.7.32 |
pe2aHostEntryEntry for configuration table of e2aHost Pe2aHostEntry .1.3.6.1.4.1.994.3.4.7.32.1 |
pe2aHostDescriptionDescription of the connection.rw DescriptionString .1.3.6.1.4.1.994.3.4.7.32.1.3 |
pe2aHostConfiguredIf set to true, this route will be used by E2A.rw Configured .1.3.6.1.4.1.994.3.4.7.32.1.10 |
pe2aHostIpAddressThe IP address of the remote device.rw IpAddress .1.3.6.1.4.1.994.3.4.7.32.1.14 |
pe2aHostLevel0Alarm level associated with the online state.rw Level .1.3.6.1.4.1.994.3.4.7.32.1.17 |
pe2aHostLevel1Alarm level associated with the offline state.rw Level .1.3.6.1.4.1.994.3.4.7.32.1.18 |
pe2aHostLevel2Alarm level associated with the connecting state.rw Level .1.3.6.1.4.1.994.3.4.7.32.1.19 |
pe2aHostRosterIDSerial port number to use when connecting to WebMon.rw Integer32 .1.3.6.1.4.1.994.3.4.7.32.1.37 |
pe2aHostPollAddressThe E2A address of the remote device.rw Integer32 .1.3.6.1.4.1.994.3.4.7.32.1.56 |
pe2aHostIPPortNumIP port number to use when connecting to the remote device.rw Integer32 .1.3.6.1.4.1.994.3.4.7.32.1.73 |
pe2aHostTL1SID(TL1) System ID associated with this item.rw DescriptionString .1.3.6.1.4.1.994.3.4.7.32.1.116 |
pe2aHostTL1COND(TL1) Condition text associated with this item.rw DescriptionString .1.3.6.1.4.1.994.3.4.7.32.1.117 |
pe2aHostTL1Eqpt(TL1) EQPT field associated with this item.rw DescriptionString .1.3.6.1.4.1.994.3.4.7.32.1.118 |
pe2aHostTL1Env(TL1) Environmental field associated with this item.rw Boolean .1.3.6.1.4.1.994.3.4.7.32.1.119 |
pe2aHostTL1Srveff(TL1) Service Effecting field associated with this item.rw TL1Srveff .1.3.6.1.4.1.994.3.4.7.32.1.120 |
pe2aHostTL1Locn(TL1) Location field associated with this item.rw TL1Locn .1.3.6.1.4.1.994.3.4.7.32.1.121 |
pe2aHostTL1Dirn(TL1) Direction field associated with this item.rw TL1Dirn .1.3.6.1.4.1.994.3.4.7.32.1.122 |
pe2aHostIndexIndex.ro Integer32 .1.3.6.1.4.1.994.3.4.7.32.1.999 |
pderivedAnalogTableTable for configuration of derivedAnalog SEQUENCE OF PderivedAnalogEntry .1.3.6.1.4.1.994.3.4.7.33 |
pderivedAnalogEntryEntry for configuration table of derivedAnalog PderivedAnalogEntry .1.3.6.1.4.1.994.3.4.7.33.1 |
pderivedAnalogDescriptionDescription of the derived alarm point.rw DescriptionString .1.3.6.1.4.1.994.3.4.7.33.1.3 |
pderivedAnalogDesc0The description for derived values between threshold 0 and threshold 1.rw DescriptionString .1.3.6.1.4.1.994.3.4.7.33.1.4 |
pderivedAnalogDesc1The description for derived values between threshold 1 and threshold 2.rw DescriptionString .1.3.6.1.4.1.994.3.4.7.33.1.5 |
pderivedAnalogDesc2The description for derived values between threshold 2 and threshold 3.rw DescriptionString .1.3.6.1.4.1.994.3.4.7.33.1.6 |
pderivedAnalogDesc3The description for derived values between threshold 3 and threshold 4.rw DescriptionString .1.3.6.1.4.1.994.3.4.7.33.1.7 |
pderivedAnalogDesc4The description for derived values between threshold 4 and threshold 5.rw DescriptionString .1.3.6.1.4.1.994.3.4.7.33.1.8 |
pderivedAnalogConfiguredIf set to true, changes of state will be reported. If set to false, not change of states will be reported.rw Configured .1.3.6.1.4.1.994.3.4.7.33.1.10 |
pderivedAnalogSendEmailIf set to true, an email will be sent on a change of state. If false, no email will be sent.rw Boolean .1.3.6.1.4.1.994.3.4.7.33.1.11 |
pderivedAnalogSendSNMPTrapIf set to true, an SNMP trap will be sent on a change of state. If false, no SNMP trap will be sent.rw Boolean .1.3.6.1.4.1.994.3.4.7.33.1.12 |
pderivedAnalogLevel0The level for derived values between threshold 0 and threshold 1.rw Level .1.3.6.1.4.1.994.3.4.7.33.1.17 |
pderivedAnalogLevel1The level for derived values between threshold 1 and threshold 2.rw Level .1.3.6.1.4.1.994.3.4.7.33.1.18 |
pderivedAnalogLevel2The level for derived values between threshold 2 and threshold 3.rw Level .1.3.6.1.4.1.994.3.4.7.33.1.19 |
pderivedAnalogLevel3The level for derived values between threshold 3 and threshold 4.rw Level .1.3.6.1.4.1.994.3.4.7.33.1.20 |
pderivedAnalogLevel4The level for derived values between threshold 4 and threshold 5.rw Level .1.3.6.1.4.1.994.3.4.7.33.1.21 |
pderivedAnalogThresh0This is the maximum analog derived value.rw DescriptionString .1.3.6.1.4.1.994.3.4.7.33.1.28 |
pderivedAnalogThresh1This is the first threshold derived value.rw DescriptionString .1.3.6.1.4.1.994.3.4.7.33.1.29 |
pderivedAnalogThresh2This is the second threshold derived value.rw DescriptionString .1.3.6.1.4.1.994.3.4.7.33.1.30 |
pderivedAnalogThresh3This is the third threshold derived value.rw DescriptionString .1.3.6.1.4.1.994.3.4.7.33.1.31 |
pderivedAnalogThresh4This is the fourth threshold derived value.rw DescriptionString .1.3.6.1.4.1.994.3.4.7.33.1.32 |
pderivedAnalogThresh5This is the minimum threshold derived value.rw DescriptionString .1.3.6.1.4.1.994.3.4.7.33.1.33 |
pderivedAnalogUnitsDescription of the units of measurement.rw DescriptionString .1.3.6.1.4.1.994.3.4.7.33.1.46 |
pderivedAnalogLiveDescriptionThe current description of the alarm state.ro DescriptionString .1.3.6.1.4.1.994.3.4.7.33.1.64 |
pderivedAnalogLiveLevelThe current level of the alarm.ro DescriptionString .1.3.6.1.4.1.994.3.4.7.33.1.65 |
pderivedAnalogLiveRawThe current derived reading from the analog devices. This value will alwaysbe between the threshold 0 and threshold 5 values.ro DescriptionString .1.3.6.1.4.1.994.3.4.7.33.1.66 |
pderivedAnalogLiveTimeThe time of the last change of state.ro DescriptionString .1.3.6.1.4.1.994.3.4.7.33.1.67 |
pderivedAnalogElementAPkgPackage where the alarm point is located for element A.rw Integer32 .1.3.6.1.4.1.994.3.4.7.33.1.90 |
pderivedAnalogElementAPointAlarm point for element A.rw Integer32 .1.3.6.1.4.1.994.3.4.7.33.1.91 |
pderivedAnalogElementBPkgPackage where the alarm point is located for element B.rw Integer32 .1.3.6.1.4.1.994.3.4.7.33.1.92 |
pderivedAnalogElementBPointAlarm point for element B.rw Integer32 .1.3.6.1.4.1.994.3.4.7.33.1.93 |
pderivedAnalogFormulaThe formula that will be used to compute the derived alarm.rw DescriptionString .1.3.6.1.4.1.994.3.4.7.33.1.95 |
pderivedAnalogTL1SID(TL1) System ID associated with this item.rw DescriptionString .1.3.6.1.4.1.994.3.4.7.33.1.116 |
pderivedAnalogTL1COND(TL1) Condition text associated with this item.rw DescriptionString .1.3.6.1.4.1.994.3.4.7.33.1.117 |
pderivedAnalogTL1Eqpt(TL1) EQPT field associated with this item.rw DescriptionString .1.3.6.1.4.1.994.3.4.7.33.1.118 |
pderivedAnalogTL1Env(TL1) Environmental field associated with this item.rw Boolean .1.3.6.1.4.1.994.3.4.7.33.1.119 |
pderivedAnalogTL1Srveff(TL1) Service Effecting field associated with this item.rw TL1Srveff .1.3.6.1.4.1.994.3.4.7.33.1.120 |
pderivedAnalogTL1Locn(TL1) Location field associated with this item.rw TL1Locn .1.3.6.1.4.1.994.3.4.7.33.1.121 |
pderivedAnalogTL1Dirn(TL1) Direction field associated with this item.rw TL1Dirn .1.3.6.1.4.1.994.3.4.7.33.1.122 |
pderivedAnalogIndexIndex.ro Integer32 .1.3.6.1.4.1.994.3.4.7.33.1.999 |
pgpsTableTable for configuration of gps SEQUENCE OF PgpsEntry .1.3.6.1.4.1.994.3.4.7.34 |
pgpsEntryEntry for configuration table of gps PgpsEntry .1.3.6.1.4.1.994.3.4.7.34.1 |
pgpsDescriptionDescription of the onboard device.ro DescriptionString .1.3.6.1.4.1.994.3.4.7.34.1.3 |
pgpsDesc0The description for values between threshold 0 and threshold 1.rw DescriptionString .1.3.6.1.4.1.994.3.4.7.34.1.4 |
pgpsDesc1The description for values between threshold 1 and threshold 2.rw DescriptionString .1.3.6.1.4.1.994.3.4.7.34.1.5 |
pgpsDesc2The description for values between threshold 2 and threshold 3.rw DescriptionString .1.3.6.1.4.1.994.3.4.7.34.1.6 |
pgpsDesc3The description for values between threshold 3 and threshold 4.rw DescriptionString .1.3.6.1.4.1.994.3.4.7.34.1.7 |
pgpsDesc4The description for values between threshold 4 and threshold 5.rw DescriptionString .1.3.6.1.4.1.994.3.4.7.34.1.8 |
pgpsConfiguredIf set to true, the onboard sensors will be used. If set to false the will be ignored.rw Configured .1.3.6.1.4.1.994.3.4.7.34.1.10 |
pgpsSendEmailIf set to true an email event will be set when a threshold is crossed. If set to false no email event will be sent.rw Boolean .1.3.6.1.4.1.994.3.4.7.34.1.11 |
pgpsSendSNMPTrapIf set to true an SNMP trap will be set when a threshold is crossed. If set to false no SNMP trap will be sent.rw Boolean .1.3.6.1.4.1.994.3.4.7.34.1.12 |
pgpsLevel0The level for values between threshold 0 and threshold 1.rw Level .1.3.6.1.4.1.994.3.4.7.34.1.17 |
pgpsLevel1The level for values between threshold 1 and threshold 2.rw Level .1.3.6.1.4.1.994.3.4.7.34.1.18 |
pgpsLevel2The level for values between threshold 2 and threshold 3.rw Level .1.3.6.1.4.1.994.3.4.7.34.1.19 |
pgpsLevel3The level for values between threshold 3 and threshold 4.rw Level .1.3.6.1.4.1.994.3.4.7.34.1.20 |
pgpsLevel4The level for values between threshold 4 and threshold 5.rw Level .1.3.6.1.4.1.994.3.4.7.34.1.21 |
pgpsThresh0This is the minimun analog value.ro DescriptionString .1.3.6.1.4.1.994.3.4.7.34.1.28 |
pgpsThresh1This is the first threshold value.rw DescriptionString .1.3.6.1.4.1.994.3.4.7.34.1.29 |
pgpsThresh2This is the second threshold value.rw DescriptionString .1.3.6.1.4.1.994.3.4.7.34.1.30 |
pgpsThresh3This is the third threshold value.rw DescriptionString .1.3.6.1.4.1.994.3.4.7.34.1.31 |
pgpsThresh4This is the fourth threshold value.rw DescriptionString .1.3.6.1.4.1.994.3.4.7.34.1.32 |
pgpsThresh5This is the maximum threshold value.ro DescriptionString .1.3.6.1.4.1.994.3.4.7.34.1.33 |
pgpsUnitsDescription of the units of measurement.ro DescriptionString .1.3.6.1.4.1.994.3.4.7.34.1.46 |
pgpsLiveDescriptionThe description of the current state of the onboard sensorro DescriptionString .1.3.6.1.4.1.994.3.4.7.34.1.64 |
pgpsLiveLevelThe level of the current state of the onboard sensor.ro DescriptionString .1.3.6.1.4.1.994.3.4.7.34.1.65 |
pgpsLiveRawThe current reading from the onboard sensor. This value will always be between the threshold 0 and threshold 5 values.ro DescriptionString .1.3.6.1.4.1.994.3.4.7.34.1.66 |
pgpsLiveTimeThe time of the last event.ro DescriptionString .1.3.6.1.4.1.994.3.4.7.34.1.67 |
pgpsTL1SID(TL1) System ID associated with this item.rw DescriptionString .1.3.6.1.4.1.994.3.4.7.34.1.116 |
pgpsTL1COND(TL1) Condition text associated with this item.rw DescriptionString .1.3.6.1.4.1.994.3.4.7.34.1.117 |
pgpsTL1Eqpt(TL1) EQPT field associated with this item.rw DescriptionString .1.3.6.1.4.1.994.3.4.7.34.1.118 |
pgpsTL1Env(TL1) Environmental field associated with this item.rw Boolean .1.3.6.1.4.1.994.3.4.7.34.1.119 |
pgpsTL1Srveff(TL1) Service Effecting field associated with this item.rw TL1Srveff .1.3.6.1.4.1.994.3.4.7.34.1.120 |
pgpsTL1Locn(TL1) Location field associated with this item.rw TL1Locn .1.3.6.1.4.1.994.3.4.7.34.1.121 |
pgpsTL1Dirn(TL1) Direction field associated with this item.rw TL1Dirn .1.3.6.1.4.1.994.3.4.7.34.1.122 |
pgpsIndexIndex.ro Integer32 .1.3.6.1.4.1.994.3.4.7.34.1.999 |
pportRedirectTableTable for configuration of portRedirect SEQUENCE OF PportRedirectEntry .1.3.6.1.4.1.994.3.4.7.35 |
pportRedirectEntryEntry for configuration table of portRedirect PportRedirectEntry .1.3.6.1.4.1.994.3.4.7.35.1 |
pportRedirectDescriptionDescription of the connection.rw DescriptionString .1.3.6.1.4.1.994.3.4.7.35.1.3 |
pportRedirectConfiguredIf set to true, this route will be allowed.rw Configured .1.3.6.1.4.1.994.3.4.7.35.1.10 |
pportRedirectIpAddressThe IP address of the remote device.rw IpAddress .1.3.6.1.4.1.994.3.4.7.35.1.14 |
pportRedirectReadPeriodInactivity timeout (in minutes).rw Integer32 .1.3.6.1.4.1.994.3.4.7.35.1.23 |
pportRedirectRosterIDIP port number to use when connecting to the remote device.rw Integer32 .1.3.6.1.4.1.994.3.4.7.35.1.37 |
pportRedirectIPPortNumIP port number to use when connecting to WebMon.rw Integer32 .1.3.6.1.4.1.994.3.4.7.35.1.73 |
pportRedirectIndexIndex.ro Integer32 .1.3.6.1.4.1.994.3.4.7.35.1.999 |
pscheduleATableTable for configuration of scheduleA SEQUENCE OF PscheduleAEntry .1.3.6.1.4.1.994.3.4.7.36 |
pscheduleAEntryEntry for configuration table of scheduleA PscheduleAEntry .1.3.6.1.4.1.994.3.4.7.36.1 |
pscheduleADayOfWeekThe day of the weekro DayOfWeek .1.3.6.1.4.1.994.3.4.7.36.1.102 |
pscheduleAConfiguredStateThe state of the schedule at the beginning of the day.rw ConfiguredState .1.3.6.1.4.1.994.3.4.7.36.1.103 |
pscheduleAConfigured1The state of the schedule between time markers 1 and 2.rw ConfiguredState .1.3.6.1.4.1.994.3.4.7.36.1.104 |
pscheduleAConfigured2The state of the schedule between time markers 2 and 3.rw ConfiguredState .1.3.6.1.4.1.994.3.4.7.36.1.105 |
pscheduleAConfigured3The state of the schedule between time markers 3 and 4.rw ConfiguredState .1.3.6.1.4.1.994.3.4.7.36.1.106 |
pscheduleAConfigured4The state of the schedule at the end of the day.rw ConfiguredState .1.3.6.1.4.1.994.3.4.7.36.1.107 |
pscheduleATime0Time marker 0, the beginning of the day.ro DescriptionString .1.3.6.1.4.1.994.3.4.7.36.1.108 |
pscheduleATime1Time marker 1.rw DescriptionString .1.3.6.1.4.1.994.3.4.7.36.1.109 |
pscheduleATime2Time marker 2.rw DescriptionString .1.3.6.1.4.1.994.3.4.7.36.1.110 |
pscheduleATime3Time marker 3.rw DescriptionString .1.3.6.1.4.1.994.3.4.7.36.1.111 |
pscheduleATime4Time marker 4.rw DescriptionString .1.3.6.1.4.1.994.3.4.7.36.1.112 |
pscheduleATime5Time marker 5, the end of the day.ro DescriptionString .1.3.6.1.4.1.994.3.4.7.36.1.113 |
pscheduleAIndexIndex.ro Integer32 .1.3.6.1.4.1.994.3.4.7.36.1.999 |
pscheduleBTableTable for configuration of scheduleB SEQUENCE OF PscheduleBEntry .1.3.6.1.4.1.994.3.4.7.37 |
pscheduleBEntryEntry for configuration table of scheduleB PscheduleBEntry .1.3.6.1.4.1.994.3.4.7.37.1 |
pscheduleBDayOfWeekThe day of the weekro DayOfWeek .1.3.6.1.4.1.994.3.4.7.37.1.102 |
pscheduleBConfiguredStateThe state of the schedule at the beginning of the day.rw ConfiguredState .1.3.6.1.4.1.994.3.4.7.37.1.103 |
pscheduleBConfigured1The state of the schedule between time markers 1 and 2.rw ConfiguredState .1.3.6.1.4.1.994.3.4.7.37.1.104 |
pscheduleBConfigured2The state of the schedule between time markers 2 and 3.rw ConfiguredState .1.3.6.1.4.1.994.3.4.7.37.1.105 |
pscheduleBConfigured3The state of the schedule between time markers 3 and 4.rw ConfiguredState .1.3.6.1.4.1.994.3.4.7.37.1.106 |
pscheduleBConfigured4The state of the schedule at the end of the day.rw ConfiguredState .1.3.6.1.4.1.994.3.4.7.37.1.107 |
pscheduleBTime0Time marker 0, the beginning of the day.ro DescriptionString .1.3.6.1.4.1.994.3.4.7.37.1.108 |
pscheduleBTime1Time marker 1.rw DescriptionString .1.3.6.1.4.1.994.3.4.7.37.1.109 |
pscheduleBTime2Time marker 2.rw DescriptionString .1.3.6.1.4.1.994.3.4.7.37.1.110 |
pscheduleBTime3Time marker 3.rw DescriptionString .1.3.6.1.4.1.994.3.4.7.37.1.111 |
pscheduleBTime4Time marker 4.rw DescriptionString .1.3.6.1.4.1.994.3.4.7.37.1.112 |
pscheduleBTime5Time marker 5, the end of the day.ro DescriptionString .1.3.6.1.4.1.994.3.4.7.37.1.113 |
pscheduleBIndexIndex.ro Integer32 .1.3.6.1.4.1.994.3.4.7.37.1.999 |
pscheduleCTableTable for configuration of scheduleC SEQUENCE OF PscheduleCEntry .1.3.6.1.4.1.994.3.4.7.38 |
pscheduleCEntryEntry for configuration table of scheduleC PscheduleCEntry .1.3.6.1.4.1.994.3.4.7.38.1 |
pscheduleCDayOfWeekThe day of the weekro DayOfWeek .1.3.6.1.4.1.994.3.4.7.38.1.102 |
pscheduleCConfiguredStateThe state of the schedule at the beginning of the day.rw ConfiguredState .1.3.6.1.4.1.994.3.4.7.38.1.103 |
pscheduleCConfigured1The state of the schedule between time markers 1 and 2.rw ConfiguredState .1.3.6.1.4.1.994.3.4.7.38.1.104 |
pscheduleCConfigured2The state of the schedule between time markers 2 and 3.rw ConfiguredState .1.3.6.1.4.1.994.3.4.7.38.1.105 |
pscheduleCConfigured3The state of the schedule between time markers 3 and 4.rw ConfiguredState .1.3.6.1.4.1.994.3.4.7.38.1.106 |
pscheduleCConfigured4The state of the schedule at the end of the day.rw ConfiguredState .1.3.6.1.4.1.994.3.4.7.38.1.107 |
pscheduleCTime0Time marker 0, the beginning of the day.ro DescriptionString .1.3.6.1.4.1.994.3.4.7.38.1.108 |
pscheduleCTime1Time marker 1.rw DescriptionString .1.3.6.1.4.1.994.3.4.7.38.1.109 |
pscheduleCTime2Time marker 2.rw DescriptionString .1.3.6.1.4.1.994.3.4.7.38.1.110 |
pscheduleCTime3Time marker 3.rw DescriptionString .1.3.6.1.4.1.994.3.4.7.38.1.111 |
pscheduleCTime4Time marker 4.rw DescriptionString .1.3.6.1.4.1.994.3.4.7.38.1.112 |
pscheduleCTime5Time marker 5, the end of the day.ro DescriptionString .1.3.6.1.4.1.994.3.4.7.38.1.113 |
pscheduleCIndexIndex.ro Integer32 .1.3.6.1.4.1.994.3.4.7.38.1.999 |
pscheduleDTableTable for configuration of scheduleD SEQUENCE OF PscheduleDEntry .1.3.6.1.4.1.994.3.4.7.39 |
pscheduleDEntryEntry for configuration table of scheduleD PscheduleDEntry .1.3.6.1.4.1.994.3.4.7.39.1 |
pscheduleDDayOfWeekThe day of the weekro DayOfWeek .1.3.6.1.4.1.994.3.4.7.39.1.102 |
pscheduleDConfiguredStateThe state of the schedule at the beginning of the day.rw ConfiguredState .1.3.6.1.4.1.994.3.4.7.39.1.103 |
pscheduleDConfigured1The state of the schedule between time markers 1 and 2.rw ConfiguredState .1.3.6.1.4.1.994.3.4.7.39.1.104 |
pscheduleDConfigured2The state of the schedule between time markers 2 and 3.rw ConfiguredState .1.3.6.1.4.1.994.3.4.7.39.1.105 |
pscheduleDConfigured3The state of the schedule between time markers 3 and 4.rw ConfiguredState .1.3.6.1.4.1.994.3.4.7.39.1.106 |
pscheduleDConfigured4The state of the schedule at the end of the day.rw ConfiguredState .1.3.6.1.4.1.994.3.4.7.39.1.107 |
pscheduleDTime0Time marker 0, the beginning of the day.ro DescriptionString .1.3.6.1.4.1.994.3.4.7.39.1.108 |
pscheduleDTime1Time marker 1.rw DescriptionString .1.3.6.1.4.1.994.3.4.7.39.1.109 |
pscheduleDTime2Time marker 2.rw DescriptionString .1.3.6.1.4.1.994.3.4.7.39.1.110 |
pscheduleDTime3Time marker 3.rw DescriptionString .1.3.6.1.4.1.994.3.4.7.39.1.111 |
pscheduleDTime4Time marker 4.rw DescriptionString .1.3.6.1.4.1.994.3.4.7.39.1.112 |
pscheduleDTime5Time marker 5, the end of the day.ro DescriptionString .1.3.6.1.4.1.994.3.4.7.39.1.113 |
pscheduleDIndexIndex.ro Integer32 .1.3.6.1.4.1.994.3.4.7.39.1.999 |
tl1Settings OBJECT IDENTIFIER .1.3.6.1.4.1.994.3.4.7.40 |
tl1SettingsTL1Issue(TL1) TL1 issue associated with this device.rw TL1Issue .1.3.6.1.4.1.994.3.4.7.40.123 |
pDCPFProtocolTableTable for configuration of DCPFProtocol SEQUENCE OF PDCPFProtocolEntry .1.3.6.1.4.1.994.3.4.7.41 |
pDCPFProtocolEntryEntry for configuration table of DCPFProtocol PDCPFProtocolEntry .1.3.6.1.4.1.994.3.4.7.41.1 |
pDCPFProtocolDescriptionDescription of the input device that DCPF will poll.ro DescriptionString .1.3.6.1.4.1.994.3.4.7.41.1.3 |
pDCPFProtocolConfiguredIf set to true, this input will be polled in DCPF. If set to false, it will not be polled.rw Configured .1.3.6.1.4.1.994.3.4.7.41.1.10 |
pDCPFProtocolBaseDCPFDisplayBase DCPF display for this input device.rw Integer32 .1.3.6.1.4.1.994.3.4.7.41.1.127 |
pDCPFProtocolIndexIndex.ro Integer32 .1.3.6.1.4.1.994.3.4.7.41.1.999 |
dcpfSettings OBJECT IDENTIFIER .1.3.6.1.4.1.994.3.4.7.42 |
dcpfSettingsDCPFAddressBase DCPF Address.rw Integer32 .1.3.6.1.4.1.994.3.4.7.42.128 |
pTABSProtocolTableTable for configuration of TABSProtocol SEQUENCE OF PTABSProtocolEntry .1.3.6.1.4.1.994.3.4.7.43 |
pTABSProtocolEntryEntry for configuration table of TABSProtocol PTABSProtocolEntry .1.3.6.1.4.1.994.3.4.7.43.1 |
pTABSProtocolDescriptionDescription of the input device that TABS will poll.ro DescriptionString .1.3.6.1.4.1.994.3.4.7.43.1.3 |
pTABSProtocolConfiguredIf set to true, this input will be polled in TABS. If set to false, it will not be polled.rw Configured .1.3.6.1.4.1.994.3.4.7.43.1.10 |
pTABSProtocolBaseTABSDisplayBase TABS display for this input device.rw Integer32 .1.3.6.1.4.1.994.3.4.7.43.1.129 |
pTABSProtocolIndexIndex.ro Integer32 .1.3.6.1.4.1.994.3.4.7.43.1.999 |
tabsSettings OBJECT IDENTIFIER .1.3.6.1.4.1.994.3.4.7.44 |
tabsSettingsTABSAddressBase TABS Address.rw Integer32 .1.3.6.1.4.1.994.3.4.7.44.130 |
psnmpCommandsTableTable for configuration of snmpCommands SEQUENCE OF PsnmpCommandsEntry .1.3.6.1.4.1.994.3.4.7.45 |
psnmpCommandsEntryEntry for configuration table of snmpCommands PsnmpCommandsEntry .1.3.6.1.4.1.994.3.4.7.45.1 |
psnmpCommandsDescriptionName for this SNMP command.rw DescriptionString .1.3.6.1.4.1.994.3.4.7.45.1.3 |
psnmpCommandsConfiguredIf set to true, this command will be sent for matching events. If set to false, it will not be sent.rw Configured .1.3.6.1.4.1.994.3.4.7.45.1.10 |
psnmpCommandsIpAddressTarget (receiver) IP address of this SNMP command.rw IpAddress .1.3.6.1.4.1.994.3.4.7.45.1.14 |
psnmpCommandsGetSNMP community used with this command.rw DescriptionString .1.3.6.1.4.1.994.3.4.7.45.1.39 |
psnmpCommandsSnmpVersionSNMP version to be used with this command.rw SnmpVersion .1.3.6.1.4.1.994.3.4.7.45.1.42 |
psnmpCommandsOutputAutoSource alarm point for this SNMP command.rw Integer32 .1.3.6.1.4.1.994.3.4.7.45.1.49 |
psnmpCommandsOutputAutoPkgPackage where the source alarm point is located.rw Integer32 .1.3.6.1.4.1.994.3.4.7.45.1.71 |
psnmpCommandsIPPortNumTarget (receiver) IP port of this SNMP command.rw Integer32 .1.3.6.1.4.1.994.3.4.7.45.1.73 |
psnmpCommandsOIDTarget OID used with this commandrw DescriptionString .1.3.6.1.4.1.994.3.4.7.45.1.132 |
psnmpCommandsSNMPVarbindTypeType of value sent to target, if this is a set command.rw SNMPVarbindType .1.3.6.1.4.1.994.3.4.7.45.1.134 |
psnmpCommandsTextNormalValue sent to target for normal condition for a set command.rw DescriptionString .1.3.6.1.4.1.994.3.4.7.45.1.135 |
psnmpCommandsTextCriticalValue sent to target for critical condition for a set command.rw DescriptionString .1.3.6.1.4.1.994.3.4.7.45.1.136 |
psnmpCommandsTextMajorValue sent to target for major condition for a set command.rw DescriptionString .1.3.6.1.4.1.994.3.4.7.45.1.137 |
psnmpCommandsTextMinorValue sent to target for minor condition for a set command.rw DescriptionString .1.3.6.1.4.1.994.3.4.7.45.1.138 |
psnmpCommandsTextStatusValue sent to target for status condition for a set command.rw DescriptionString .1.3.6.1.4.1.994.3.4.7.45.1.139 |
psnmpCommandsIndexIndex.ro Integer32 .1.3.6.1.4.1.994.3.4.7.45.1.999 |
battMon OBJECT IDENTIFIER .1.3.6.1.4.1.994.3.4.7.46 |
battMonConfiguredIf set to true, this command will be sent for matching events. If set to false, it will not be sent.rw Configured .1.3.6.1.4.1.994.3.4.7.46.10 |
battMonOutputAutoSource alarm point for this SNMP command.rw Integer32 .1.3.6.1.4.1.994.3.4.7.46.49 |
battMonOutputAutoPkgPackage where the source alarm point is located.rw Integer32 .1.3.6.1.4.1.994.3.4.7.46.71 |
pBankInfoTableTable for configuration of BankInfo SEQUENCE OF PBankInfoEntry .1.3.6.1.4.1.994.3.4.7.47 |
pBankInfoEntryEntry for configuration table of BankInfo PBankInfoEntry .1.3.6.1.4.1.994.3.4.7.47.1 |
pBankInfoDescriptionDescription of the slot contents.ro DescriptionString .1.3.6.1.4.1.994.3.4.7.47.1.3 |
pBankInfoConfiguredSchedule of when this bank is in use.rw Configured .1.3.6.1.4.1.994.3.4.7.47.1.10 |
pBankInfoPresentIf true indicates the bank is connected to the WebMon. If false indicates that the bank is not connected.ro Boolean .1.3.6.1.4.1.994.3.4.7.47.1.68 |
pBankInfoSlotIdIdentifies the type of card in slot.rw SlotId .1.3.6.1.4.1.994.3.4.7.47.1.69 |
pBankInfoIOFormatrw IOFormat .1.3.6.1.4.1.994.3.4.7.47.1.75 |
pBankInfoIndexIndex.ro Integer32 .1.3.6.1.4.1.994.3.4.7.47.1.999 |
configObjectGroupDescription. Unknown .1.3.6.1.4.1.994.3.4.7.999 |
triggers OBJECT IDENTIFIER .1.3.6.1.4.1.994.3.4.8 |
resetDeviceSetting this item to true will cause a reset of the device. Setting this item to false will have no effect.rw Boolean .1.3.6.1.4.1.994.3.4.8.1 |
commitAccountChangesSetting this item to true will cause any user account changes to go into effect immediatly. Setting this item to false will have no effect.rw Boolean .1.3.6.1.4.1.994.3.4.8.2 |
resendEventsSetting this item to true will cause the device to resend traps for any standing alarms. Setting this item to false will have no effect.rw Boolean .1.3.6.1.4.1.994.3.4.8.3 |