USHA-MIB
AI MIB Summary
Standard SNMP MIB module defining data structures for USHA-MIB.
278
Objects
Active
Status
5
Dependencies
Imported Objects
Objects
278 total| Object Name |
|---|
ingrasys OBJECT IDENTIFIER .1.3.6.1.4.1.2468 |
RFC1155-SMI Unknown .1.3.6.1.4.1.2468 |
product OBJECT IDENTIFIER .1.3.6.1.4.1.2468.1 |
upsAgent OBJECT IDENTIFIER .1.3.6.1.4.1.2468.1.2 |
ushap OBJECT IDENTIFIER .1.3.6.1.4.1.2468.1.2.1 |
upsObjectGroup OBJECT IDENTIFIER .1.3.6.1.4.1.2468.1.2.1.1 |
upsIdentGroup OBJECT IDENTIFIER .1.3.6.1.4.1.2468.1.2.1.1.1 |
upsIdentGroupManufacturerThe name of the UPS manufacturer.ro DisplayString .1.3.6.1.4.1.2468.1.2.1.1.1.1 |
upsIdentGroupModelThe UPS Model designation.ro DisplayString .1.3.6.1.4.1.2468.1.2.1.1.1.2 |
upsIdentGroupUPSFirmwareVersionThe UPS firmware/software version(s). This variable
may or may not have the same value as
upsIdentGroupAgentSoftwareVersion in some implementations.ro DisplayString .1.3.6.1.4.1.2468.1.2.1.1.1.3 |
upsIdentGroupAgentSoftwareVersionThe USHA software/firmware version. This variable may or
may not have the same value as
upsIdentGroupUPSSoftwareVersion in some implementations.ro DisplayString .1.3.6.1.4.1.2468.1.2.1.1.1.4 |
upsIdentGroupNameA string identifying the UPS. This object should be
set by the administrator.rw DisplayString .1.3.6.1.4.1.2468.1.2.1.1.1.5 |
upsIdentGroupAttachedDevicesA string identifying the devices attached to the
output(s) of the UPS. This object should be set by
the administrator.rw DisplayString .1.3.6.1.4.1.2468.1.2.1.1.1.6 |
upsIdentGroupUpsSerialNumberThe UPS serial no.ro DisplayString .1.3.6.1.4.1.2468.1.2.1.1.1.7 |
upsBatteryGroup OBJECT IDENTIFIER .1.3.6.1.4.1.2468.1.2.1.1.2 |
upsBatteryGroupStatusThe indication of the status in the UPS system's batteries.ro Enumeration .1.3.6.1.4.1.2468.1.2.1.1.2.1 |
upsBatteryGroupSecondsOnBatteryIf the unit is on battery power, the elapsed time
since the UPS last switched to battery power, or the
time since the network management subsystem was last
restarted, whichever is less. 0 shall be returned
if the unit is not on battery power.ro INTEGER .1.3.6.1.4.1.2468.1.2.1.1.2.2 |
upsBatteryGroupEstimatedMinutesRemainingAn estimate of the time to battery charge depletion
under the present load conditions if the utility power
is off and remains off, or if it were to be lost and
remain off.ro INTEGER .1.3.6.1.4.1.2468.1.2.1.1.2.3 |
upsBatteryGroupEstimatedChargeRemainingAn estimate of the battery charge remaining expressed
as a percent of full charge.ro INTEGER .1.3.6.1.4.1.2468.1.2.1.1.2.4 |
upsBatteryGroupVoltageThe magnitude of the present battery voltage in 0.1 Volt DC.ro INTEGER .1.3.6.1.4.1.2468.1.2.1.1.2.5 |
upsBatteryGroupMandatoryThe present battery mandatory.ro INTEGER -- "0.1 Amp DC" .1.3.6.1.4.1.2468.1.2.1.1.2.6 |
upsBatteryGroupTemperatureThe ambient temperature at or near the UPS Battery
casing.ro INTEGER -- "degrees 0.1 Centigrade" .1.3.6.1.4.1.2468.1.2.1.1.2.7 |
upsInputGroup OBJECT IDENTIFIER .1.3.6.1.4.1.2468.1.2.1.1.3 |
upsInputGroupLineBadsA count of the number of times the input entered an
out-of-tolerance condition as defined by the
manufacturer. This count is incremented by one each
time the input transitions from zero out-of-tolerance
lines to one or more input lines out-of-tolerance.ro Counter .1.3.6.1.4.1.2468.1.2.1.1.3.1 |
upsInputGroupNumLinesThe number of input lines utilized in this device.
This variable indicates the number of rows in the
input table.ro INTEGER .1.3.6.1.4.1.2468.1.2.1.1.3.2 |
upsInputGroupTableA list of input table entries. The number of entries
is given by the value of upsInputGroupNumLines. SEQUENCE OF UpsInputGroupEntry .1.3.6.1.4.1.2468.1.2.1.1.3.3 |
upsInputGroupEntryAn entry containing information applicable to a
particular input line. UpsInputGroupEntry .1.3.6.1.4.1.2468.1.2.1.1.3.3.1 |
upsInputGroupLineIndexThe index of UpsInputGroupEntry.ro PositiveInteger .1.3.6.1.4.1.2468.1.2.1.1.3.3.1.1 |
upsInputGroupFrequencyThe present input frequency.ro NonNegativeInteger -- "0.1 Hertz" .1.3.6.1.4.1.2468.1.2.1.1.3.3.1.2 |
upsInputGroupVoltageThe input utility line voltage in 0.1 volts.ro NonNegativeInteger (UPS-MIB) .1.3.6.1.4.1.2468.1.2.1.1.3.3.1.3 |
upsInputGroupCurrentThe magnitude of the present input current in 0.1 A.ro NonNegativeInteger (UPS-MIB) .1.3.6.1.4.1.2468.1.2.1.1.3.3.1.4 |
upsInputGroupTruePowerThe magnitude of the present input true power.ro NonNegativeInteger -- "Watts" .1.3.6.1.4.1.2468.1.2.1.1.3.3.1.5 |
upsInputGroupVoltageMaxThe maximum utility line voltage in 0.1 VAC for last 1 minute.ro NonNegativeInteger (UPS-MIB) .1.3.6.1.4.1.2468.1.2.1.1.3.3.1.6 |
upsInputGroupVoltageMinThe minimum utility line voltage in 0.1 VAC for last 1 minute.ro NonNegativeInteger (UPS-MIB) .1.3.6.1.4.1.2468.1.2.1.1.3.3.1.7 |
upsOutputGroup OBJECT IDENTIFIER .1.3.6.1.4.1.2468.1.2.1.1.4 |
upsOutputGroupSourceThe present source of output power. The enumeration
none(2) indicates that there is no source of output
power (and therefore no output power), for example,
the system has opened the output breaker.ro Enumeration .1.3.6.1.4.1.2468.1.2.1.1.4.1 |
upsOutputGroupFrequencyThe current output frequency of the UPS system in 0.1 of HZ.ro INTEGER .1.3.6.1.4.1.2468.1.2.1.1.4.2 |
upsOutputGroupNumLinesThe number of output lines utilized in this device.
This variable indicates the number of rows in the
output table.ro INTEGER .1.3.6.1.4.1.2468.1.2.1.1.4.3 |
upsOutputGroupTableA list of output table entries. The number of
entries is given by the value of upsOutputGroupNumLines. SEQUENCE OF UpsOutputGroupEntry .1.3.6.1.4.1.2468.1.2.1.1.4.4 |
upsOutputGroupEntryAn entry containing information applicable to a
particular output line. UpsOutputGroupEntry .1.3.6.1.4.1.2468.1.2.1.1.4.4.1 |
upsOutputGroupLineIndexThe output line identifier.ro PositiveInteger .1.3.6.1.4.1.2468.1.2.1.1.4.4.1.1 |
upsOutputGroupVoltageThe output voltage of the UPS system in 0.1 volts.ro NonNegativeInteger (UPS-MIB) .1.3.6.1.4.1.2468.1.2.1.1.4.4.1.2 |
upsOutputGroupCurrentThe output current of the UPS system in 0.1 Amps.ro NonNegativeInteger (UPS-MIB) .1.3.6.1.4.1.2468.1.2.1.1.4.4.1.3 |
upsOutputGroupPowerThe present output true power.ro NonNegativeInteger -- "Watts" .1.3.6.1.4.1.2468.1.2.1.1.4.4.1.4 |
upsOutputGroupPercentLoadThe percentage of the UPS power capacity presently
being used on this output line, i.e., the greater of
the percent load of true power capacity and the
percent load of VA.ro INTEGER .1.3.6.1.4.1.2468.1.2.1.1.4.4.1.5 |
upsBypassGroup OBJECT IDENTIFIER .1.3.6.1.4.1.2468.1.2.1.1.5 |
upsBypassGroupFrequencyThe present bypass frequency.ro INTEGER .1.3.6.1.4.1.2468.1.2.1.1.5.1 |
upsBypassGroupNumLinesThe number of bypass lines utilized in this device.
This entry indicates the number of rows in the bypass
table.ro INTEGER .1.3.6.1.4.1.2468.1.2.1.1.5.2 |
upsBypassGroupTableA list of bypass table entries. The number of
entries is given by the value of upsBypassGroupNumLines. SEQUENCE OF UpsBypassGroupEntry .1.3.6.1.4.1.2468.1.2.1.1.5.3 |
upsBypassGroupEntryAn entry containing information applicable to a
particular bypass input. UpsBypassGroupEntry .1.3.6.1.4.1.2468.1.2.1.1.5.3.1 |
upsBypassGroupLineIndexThe bypass line identifier.ro PositiveInteger .1.3.6.1.4.1.2468.1.2.1.1.5.3.1.1 |
upsBypassGroupVoltageThe present bypass voltage.ro NonNegativeInteger (UPS-MIB) .1.3.6.1.4.1.2468.1.2.1.1.5.3.1.2 |
upsBypassGroupCurrentThe present bypass current.ro NonNegativeInteger (UPS-MIB) .1.3.6.1.4.1.2468.1.2.1.1.5.3.1.3 |
upsBypassGroupPowerThe present true power conveyed by the bypass.ro NonNegativeInteger -- "Watts" .1.3.6.1.4.1.2468.1.2.1.1.5.3.1.4 |
upsTestGroup OBJECT IDENTIFIER .1.3.6.1.4.1.2468.1.2.1.1.6 |
upsTestBatteryTestSettingTimeThe object specify the test time for battery test.rw INTEGER .1.3.6.1.4.1.2468.1.2.1.1.6.1 |
upsBatteryTestThis object specify the battery test type and initiate
battery test. If battTestWithTime selected, the test
time is refer to upsTestBatteryTestTime.rw Enumeration .1.3.6.1.4.1.2468.1.2.1.1.6.2 |
upsTestBatteryTestResultThe results of the current or last UPS diagnostics
test performed. The values for donePassed(1),
doneWarning(2), and doneError(3) indicate that the
test completed either successfully, with a warning, or
with an error, respectively. The value aborted(4) is
returned for tests which are aborted by setting the
value of upsTestId to upsTestAbortTestInProgress.
Tests which have not yet concluded are indicated by
inProgress(5). The value noTestsInitiated(6)
indicates that no previous test results are available,
such as is the case when no tests have been run since
the last reinitialization of the network management
subsystem and the system has no provision for non-
volatile storage of test results.ro Enumeration .1.3.6.1.4.1.2468.1.2.1.1.6.3 |
upsTestBatteryTestStartTimeThe value of the time the test in progress was initiated,
or, if no test is in progress, the time the previous test
was initiated. If the value of upsTestBatteryTestResult
is noTestsInitiated(6), upsTestStartTime has the value
01/01/1970 00:00:00.ro DisplayString .1.3.6.1.4.1.2468.1.2.1.1.6.4 |
upsTestBatteryTestElapsedTimeThe amount of time, in TimeTicks, since the test in
progress was initiated, or, if no test is in progress,
the previous test took to complete. If the value of
upsTestResultsSummary is noTestsInitiated(6),
upsTestElapsedTime has the value 00:00:00.00.ro DisplayString .1.3.6.1.4.1.2468.1.2.1.1.6.5 |
upsBatteryTestScheduleTableTable which describes the schedule for automatically battery
test. SEQUENCE OF UpsBatteryTestScheduleEntry .1.3.6.1.4.1.2468.1.2.1.1.6.6 |
upsBatteryTestScheduleEntry UpsBatteryTestScheduleEntry .1.3.6.1.4.1.2468.1.2.1.1.6.6.1 |
upsBatteryTestScheduleIndexThe index of battery test scheduled.ro INTEGER .1.3.6.1.4.1.2468.1.2.1.1.6.6.1.1 |
upsBatteryTestScheduleDayThe weekday on which the UPS should start battery test.rw Enumeration .1.3.6.1.4.1.2468.1.2.1.1.6.6.1.2 |
upsBatteryTestScheduleTimeThe time that the battery test will be initiated in hh:mm format.rw DisplayString .1.3.6.1.4.1.2468.1.2.1.1.6.6.1.3 |
upsBatteryTestScheduleTypeThe type of battery test.rw Enumeration .1.3.6.1.4.1.2468.1.2.1.1.6.6.1.4 |
upsBatteryTestScheduleTestWithTimeThe battTestWithTime of battery test is supported or not.ro Enumeration .1.3.6.1.4.1.2468.1.2.1.1.6.6.1.5 |
upsBatteryTestScheduleSpecialDayThe special day that the battery test will be initiated in dd/mm/yyyy format.rw DisplayString .1.3.6.1.4.1.2468.1.2.1.1.6.6.1.6 |
upsControlGroup OBJECT IDENTIFIER .1.3.6.1.4.1.2468.1.2.1.1.7 |
upsControlUpsShutdownDelayThe delay in seconds the UPS remains on after being told
to turn off.rw INTEGER .1.3.6.1.4.1.2468.1.2.1.1.7.1 |
upsControlUpsSleepTimeThe time in minutes for the UPS to go to sleep when
instructed. When in sleep mode, the UPS will not provide
output power regardless of the input line state. Once the
specified time has elapsed, output power will be restored.
This is a configuration setting. The UPS will not go to
sleep until told to do so by the manager from a management
station.
Any input value is allowed, however the UPS only recognizes
0 - 9999 minutes in one minute increments.
If the provided value is higher than the highest acceptable
value, the highest acceptable value is used.rw INTEGER .1.3.6.1.4.1.2468.1.2.1.1.7.2 |
upsControlUpsOnOffControlSetting this variable to control UPS output status.
turnUpsOff(1) will set UPS turn off output after
upsControlUpsShutdownDelay period expired.
putUpsToSleep(2) will set UPS turn off output after
upsControlUpsShutdownDelay period expired, UPS output
will stay off with the period defined by
upsControlUpsSleepTime, then turn output on.
turnOnUpsOrCancelShutdown(3) can used to turn on UPS
output, or cancel any shutdown process.rw Enumeration .1.3.6.1.4.1.2468.1.2.1.1.7.3 |
upsControlShutdownParametersTableTable which describes the parametes for shutdown process
when shutdown event occurs SEQUENCE OF UpsControlShutdownParametersEntry .1.3.6.1.4.1.2468.1.2.1.1.7.4 |
upsControlShutdownParametersEntry UpsControlShutdownParametersEntry .1.3.6.1.4.1.2468.1.2.1.1.7.4.1 |
upsControlEventThe shutdown event identificationro DisplayString SYNTAX INTEGER { acFail(1), batteryLow (2), upsOverload (3), upsOverTempeature (4), weeklySchedule (5), specialDaySchedule (6), emdTemperatureOverThreshold (7), emdAlarm1 (8), emdAlarm2 (9) } .1.3.6.1.4.1.2468.1.2.1.1.7.4.1.1 |
upsControlEventStatusStatus of the corresponding shutdown Event.
When set to disable(), shutdown process will not start when
corresponding event occured.rw Enumeration .1.3.6.1.4.1.2468.1.2.1.1.7.4.1.2 |
upsControlDelayThe Delay after the occurance of the curresponding shutdown
event that USHA should issue shutdown request to
connected clients. For WeeklyScheduledShutdown and
SpecialScheduledShutdown, this is the time before the
configured Shutdowntime when USHA will start sending the
warning message to the connected clients. The value is in
units of minutes.rw INTEGER .1.3.6.1.4.1.2468.1.2.1.1.7.4.1.3 |
upsControlFirstWarningThe delay after the occurance of the curresponding shutdown
event that the USHA will start sending the warning
message to the connected clients. The value is in units of
secondsrw INTEGER .1.3.6.1.4.1.2468.1.2.1.1.7.4.1.4 |
upsControlWarningIntervalThe frequency of sending warning messages to the connected
clients when the curresponding shutdown event occurs.
The value is in units of seconds.rw INTEGER .1.3.6.1.4.1.2468.1.2.1.1.7.4.1.5 |
upsControlWeeklyScheduleTableThe table to schedule shutting down the ups by weekly. SEQUENCE OF UpsControlWeeklyScheduleEntry .1.3.6.1.4.1.2468.1.2.1.1.7.5 |
upsControlWeeklyScheduleEntryThe entries for each day. UpsControlWeeklyScheduleEntry .1.3.6.1.4.1.2468.1.2.1.1.7.5.1 |
upsControlWeeklyIndexThe index of scheduled events.ro INTEGER .1.3.6.1.4.1.2468.1.2.1.1.7.5.1.1 |
upsControlWeeklyShutdownDayThe weekday on which the UPS should shut down.rw Enumeration .1.3.6.1.4.1.2468.1.2.1.1.7.5.1.2 |
upsControlWeeklyShutdownTimeThe time that the process of shutting down the UPS will be initiated
in hh:mm format.rw DisplayString .1.3.6.1.4.1.2468.1.2.1.1.7.5.1.3 |
upsControlWeeklyRestartDayThe weekday on which the UPS should restartrw Enumeration .1.3.6.1.4.1.2468.1.2.1.1.7.5.1.4 |
upsControlWeeklyRestartTimeThe time the UPS will restart in hh:mm format.rw DisplayString .1.3.6.1.4.1.2468.1.2.1.1.7.5.1.5 |
upsControlSpecialScheduleTableThe table to schedule shutting down the ups. SEQUENCE OF UpsControlSpecialScheduleEntry .1.3.6.1.4.1.2468.1.2.1.1.7.6 |
upsControlSpecialScheduleEntryThe entries for each day. UpsControlSpecialScheduleEntry .1.3.6.1.4.1.2468.1.2.1.1.7.6.1 |
upsControlSpecialIndexThe index of scheduled events.ro INTEGER .1.3.6.1.4.1.2468.1.2.1.1.7.6.1.1 |
upsControlSpecialShutdownDayThe date on which the UPS should shut down in dd/mm/yyyy
format.rw DisplayString .1.3.6.1.4.1.2468.1.2.1.1.7.6.1.2 |
upsControlSpecialShutdownTimeThe time that the process of shutting down the UPS will be initiated
in hh:mm formatrw DisplayString .1.3.6.1.4.1.2468.1.2.1.1.7.6.1.3 |
upsControlSpecialRestartDayThe date on which the UPS should restart in dd/mm/yyyy formatrw DisplayString .1.3.6.1.4.1.2468.1.2.1.1.7.6.1.4 |
upsControlSpecialRestartTimeThe time the UPS will restart in hh:mm format.rw DisplayString .1.3.6.1.4.1.2468.1.2.1.1.7.6.1.5 |
upsConfigGroup OBJECT IDENTIFIER .1.3.6.1.4.1.2468.1.2.1.1.8 |
upsConfigGroupInputVoltageThe magnitude of the nominal input voltage. On those
systems which support read-write access to this
object, if there is an attempt to set this variable to
a value that is not supported, the request must be
rejected and the agent shall respond with an
appropriate error message, i.e., badValue for SNMPv1,
or inconsistentValue for SNMPv2.ro INTEGER .1.3.6.1.4.1.2468.1.2.1.1.8.1 |
upsConfigGroupInputFreqThe nominal input frequency. On those systems which
support read-write access to this object, if there is
an attempt to set this variable to a value that is not
supported, the request must be rejected and the agent
shall respond with an appropriate error message, i.e.,
badValue for SNMPv1, or inconsistentValue for SNMPv2.ro INTEGER .1.3.6.1.4.1.2468.1.2.1.1.8.2 |
upsConfigGroupOutputVoltageThe magnitude of the nominal output voltage. On
those systems which support read-write access to this
object, if there is an attempt to set this variable to
a value that is not supported, the request must be
rejected and the agent shall respond with an
appropriate error message, i.e., badValue for SNMPv1,
or inconsistentValue for SNMPv2.ro INTEGER .1.3.6.1.4.1.2468.1.2.1.1.8.3 |
upsConfigGroupOutputFreqThe nominal output frequency. On those systems which
support read-write access to this object, if there is
an attempt to set this variable to a value that is not
supported, the request must be rejected and the agent
shall respond with an appropriate error message, i.e.,
badValue for SNMPv1, or inconsistentValue for SNMPv2.ro INTEGER .1.3.6.1.4.1.2468.1.2.1.1.8.4 |
upsConfigGroupOutputVAThe magnitude of the nominal Volt-Amp rating.ro NonNegativeInteger -- "Volt-Amps" .1.3.6.1.4.1.2468.1.2.1.1.8.5 |
upsConfigGroupOutputPowerThe magnitude of the nominal true power rating.ro NonNegativeInteger -- "Watts" .1.3.6.1.4.1.2468.1.2.1.1.8.6 |
upsConfigGroupOverTemperatureSetPointThe maximum temperature allowed before the UPS
operation temperature is too high.rw NonNegativeInteger .1.3.6.1.4.1.2468.1.2.1.1.8.7 |
upsConfigGroupOverLoadSetPointThe maximum output load allowed before the load is
too high for UPS operation.rw NonNegativeInteger .1.3.6.1.4.1.2468.1.2.1.1.8.8 |
upsClients OBJECT IDENTIFIER .1.3.6.1.4.1.2468.1.2.1.1.9 |
upsClientsConnectedNumThe count of clients which have resgistered for UPS
shutdown control.ro NonNegativeInteger (UPS-MIB) .1.3.6.1.4.1.2468.1.2.1.1.9.1 |
upsDevicesTableThe devices powered by UPS and registered to USHA SEQUENCE OF UpsDevicesEntry .1.3.6.1.4.1.2468.1.2.1.1.9.2 |
upsDevicesEntryThe devices protected by USHA UpsDevicesEntry .1.3.6.1.4.1.2468.1.2.1.1.9.2.1 |
indexOfDeviceThe index of the device that is plugged into the UPS.ro NonNegativeInteger (UPS-MIB) .1.3.6.1.4.1.2468.1.2.1.1.9.2.1.1 |
addrOfDeviceThe ip address of the device.ro IpAddress .1.3.6.1.4.1.2468.1.2.1.1.9.2.1.2 |
nameOfDeviceThe name/description of the device plugged into the UPS.ro DisplayString .1.3.6.1.4.1.2468.1.2.1.1.9.2.1.3 |
timeOfConnectionThe device registered to USHAro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.2468.1.2.1.1.9.2.1.4 |
timeOfConnectionTimeThe device registered time to USHA.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.2468.1.2.1.1.9.2.1.5 |
timeOfConnectionTimeoutThe device timeout counter. Unit: 10 secondsro INTEGER .1.3.6.1.4.1.2468.1.2.1.1.9.2.1.6 |
agentConfig OBJECT IDENTIFIER .1.3.6.1.4.1.2468.1.2.1.1.10 |
agentConfigIpaddressThe ip address that NMS can identify the managed
devicerw IpAddress .1.3.6.1.4.1.2468.1.2.1.1.10.1 |
agentConfigGatewayThe default gateway that allow device managed
through routersrw IpAddress .1.3.6.1.4.1.2468.1.2.1.1.10.2 |
agentConfigSubnetMaskInternet address subnet maskrw IpAddress .1.3.6.1.4.1.2468.1.2.1.1.10.3 |
agentConfigDateThe date in agent, format is (dd/mm/yyyy)rw DisplayString .1.3.6.1.4.1.2468.1.2.1.1.10.4 |
agentConfigTimeThe time in agent, format is (hh:mm:ss)rw DisplayString .1.3.6.1.4.1.2468.1.2.1.1.10.5 |
agentConfigPrimaryTimeServerThe primary time server is responsible for sending the
correct time to the agent.rw IpAddress .1.3.6.1.4.1.2468.1.2.1.1.10.6 |
agentConfigSecondaryTimeServerThe secondary time server is responsible for sending the
correct time to the agent.rw IpAddress .1.3.6.1.4.1.2468.1.2.1.1.10.7 |
agentConfigHistoryLogFrequencyThe frequency of the updation of the history log. The value
is in secondsrw INTEGER .1.3.6.1.4.1.2468.1.2.1.1.10.8 |
agentConfigExtHistoryLogFrequencyThe ups parameters are sampled at the rate governed by the
mconfigHistroyLogFrequency. These sampled values are further
conslidated over period of time which is determined by this
object.rw INTEGER .1.3.6.1.4.1.2468.1.2.1.1.10.9 |
agentConfigPollRateThe frequency that proxy agent polls the connected
UPS in JBUS protocol. (unit : second)rw INTEGER .1.3.6.1.4.1.2468.1.2.1.1.10.10 |
agentConfigBaudRateThe serial port communication speed. only 9600 allowedro INTEGER .1.3.6.1.4.1.2468.1.2.1.1.10.11 |
agentConfigDhcpStatueEnable or disable DHCP/BootP capabilityrw Enumeration .1.3.6.1.4.1.2468.1.2.1.1.10.12 |
agentConfigTelnetStatueEnable or disable telnet accessrw Enumeration .1.3.6.1.4.1.2468.1.2.1.1.10.13 |
agentConfigTftpStatueEnable or disable network upgrade capabilityrw Enumeration .1.3.6.1.4.1.2468.1.2.1.1.10.14 |
agentConfigResetToDefaultReset all parameters of USHA to default valuerw Enumeration .1.3.6.1.4.1.2468.1.2.1.1.10.15 |
agentConfigRestartRestart USHArw Enumeration .1.3.6.1.4.1.2468.1.2.1.1.10.16 |
agentConfigClearAgentLogClear agent log datarw Enumeration .1.3.6.1.4.1.2468.1.2.1.1.10.17 |
agentConfigClearEventLogClear event log datarw Enumeration .1.3.6.1.4.1.2468.1.2.1.1.10.18 |
agentConfigClearExtHistoryLogClear extented history log datarw Enumeration .1.3.6.1.4.1.2468.1.2.1.1.10.19 |
agentConfigClearHistoryLogClear history log datarw Enumeration .1.3.6.1.4.1.2468.1.2.1.1.10.20 |
agentConfigTrapRetryCountThe count of repeat traps to send to NMS before trap
acknowledge received.rw INTEGER .1.3.6.1.4.1.2468.1.2.1.1.10.21 |
agentConfigTrapRetryTimeThe time between retry traps sned to NMS.rw INTEGER .1.3.6.1.4.1.2468.1.2.1.1.10.22 |
agentConfigTrapAckSignatureThe signature of trap acknowledge.rw INTEGER .1.3.6.1.4.1.2468.1.2.1.1.10.23 |
agentConfigMibVersionThe version of MIB spec.ro INTEGER .1.3.6.1.4.1.2468.1.2.1.1.10.24 |
agentConfigTrapsReceiversTableA list of managers to send traps to. The number of
entries is given by the value of agentConfigNumTrapReceivers SEQUENCE OF AgentConfigTrapsReceiversEntry .1.3.6.1.4.1.2468.1.2.1.1.10.25 |
agentConfigTrapsReceiversEntryThe managers to send traps to. AgentConfigTrapsReceiversEntry .1.3.6.1.4.1.2468.1.2.1.1.10.25.1 |
trapsIndexThe index to a trap receiver entry.ro INTEGER .1.3.6.1.4.1.2468.1.2.1.1.10.25.1.1 |
trapsReceiverAddrThe IP address of the manager to send a trap to.rw IpAddress .1.3.6.1.4.1.2468.1.2.1.1.10.25.1.2 |
receiverCommunityStringThe community name to use in the trap when
sent to the manager.rw DisplayString .1.3.6.1.4.1.2468.1.2.1.1.10.25.1.3 |
receiverNmsTypeThe trap group that NMS desired.rw Enumeration .1.3.6.1.4.1.2468.1.2.1.1.10.25.1.4 |
receiverSeverityLevelThe severity level of traps to be received by this manager.rw Enumeration .1.3.6.1.4.1.2468.1.2.1.1.10.25.1.5 |
receiverDescriptionDescription of trap receiversrw DisplayString .1.3.6.1.4.1.2468.1.2.1.1.10.25.1.6 |
agentConfigAccessControlTableA list of managers which can access USHA with private
community string. SEQUENCE OF AgentConfigAccessControlEntry .1.3.6.1.4.1.2468.1.2.1.1.10.26 |
agentConfigAccessControlEntryThe managers. AgentConfigAccessControlEntry .1.3.6.1.4.1.2468.1.2.1.1.10.26.1 |
accessIndexThe index to a access control entry.ro INTEGER .1.3.6.1.4.1.2468.1.2.1.1.10.26.1.1 |
accessControlAddrThe IP address of the manager to access USHArw IpAddress .1.3.6.1.4.1.2468.1.2.1.1.10.26.1.2 |
accessCommunityStringThe community name to use in the manager when
access USHArw DisplayString .1.3.6.1.4.1.2468.1.2.1.1.10.26.1.3 |
accessControlModeAccess type, only read/Write access type can change parameter
of USHArw Enumeration .1.3.6.1.4.1.2468.1.2.1.1.10.26.1.4 |
agentConfigDefaultLanguageThe default languauge for browser, when set to auto(1)
USHA will send page in the language depends on the
request language of browser.rw Enumeration .1.3.6.1.4.1.2468.1.2.1.1.10.27 |
emdStatus OBJECT IDENTIFIER .1.3.6.1.4.1.2468.1.2.1.1.11 |
emdSatatusEmdTypeThe type of EMD plugged into the port.ro Enumeration .1.3.6.1.4.1.2468.1.2.1.1.11.1 |
emdSatatusTemperatureThe measurement of EMD temperature, in 0.1 degreero INTEGER .1.3.6.1.4.1.2468.1.2.1.1.11.2 |
emdSatatusHumidityThe measurement of EMD humidity, in 0.1 degreero INTEGER .1.3.6.1.4.1.2468.1.2.1.1.11.3 |
emdSatatusAlarm1The EMD alarm-1 statusro Enumeration .1.3.6.1.4.1.2468.1.2.1.1.11.4 |
emdSatatusAlarm2The EMD alarm-2 statusro Enumeration .1.3.6.1.4.1.2468.1.2.1.1.11.5 |
emdConfig OBJECT IDENTIFIER .1.3.6.1.4.1.2468.1.2.1.1.12 |
usahEmdConfigEmdConfigEnable or disable to detect presence of EMDrw Enumeration .1.3.6.1.4.1.2468.1.2.1.1.12.1 |
emdConfigEmdNameDescription of EMDrw DisplayString .1.3.6.1.4.1.2468.1.2.1.1.12.2 |
emdConfigTemperature OBJECT IDENTIFIER .1.3.6.1.4.1.2468.1.2.1.1.12.3 |
emdConfigTempNameDescription of EMD temperature sensorrw DisplayString .1.3.6.1.4.1.2468.1.2.1.1.12.3.1 |
emdConfigTempHighSetPointThe set point for high temperature warning, in degreesrw INTEGER .1.3.6.1.4.1.2468.1.2.1.1.12.3.2 |
emdConfigTempHighStatusTo enable/disable high set point check with emd temperature.rw Enumeration .1.3.6.1.4.1.2468.1.2.1.1.12.3.3 |
emdConfigTempLowSetPointThe set point for low temperature warning, in degreesrw INTEGER .1.3.6.1.4.1.2468.1.2.1.1.12.3.4 |
emdConfigTempLowStatusTo enable/disable low set point check with emd temperature.rw Enumeration .1.3.6.1.4.1.2468.1.2.1.1.12.3.5 |
emdConfigTempOffsetThe offset to calibrate temperature of EMD, in degreesrw INTEGER .1.3.6.1.4.1.2468.1.2.1.1.12.3.6 |
emdConfigHumidity OBJECT IDENTIFIER .1.3.6.1.4.1.2468.1.2.1.1.12.4 |
emdConfigHumidityNameDescription of EMD humidity sensorrw DisplayString .1.3.6.1.4.1.2468.1.2.1.1.12.4.1 |
emdConfigHumidityHighSetPointThe set point for high humidity warning, in %rw INTEGER .1.3.6.1.4.1.2468.1.2.1.1.12.4.2 |
emdConfigHumidityLowStatusTo enable/disable high set point check with emd humidity.rw Enumeration .1.3.6.1.4.1.2468.1.2.1.1.12.4.3 |
emdConfigHumidityLowSetPointThe set point for low humidity warning, in %rw INTEGER .1.3.6.1.4.1.2468.1.2.1.1.12.4.4 |
emdConfigHumidityHighStatusTo enable/disable low set point check with emd humidity.rw Enumeration .1.3.6.1.4.1.2468.1.2.1.1.12.4.5 |
emdConfigHumidityOffsetThe offset to calibrate humidity of EMD, in %rw INTEGER .1.3.6.1.4.1.2468.1.2.1.1.12.4.6 |
emdConfigAlarm1 OBJECT IDENTIFIER .1.3.6.1.4.1.2468.1.2.1.1.12.5 |
emdConfigAlarm1NameDescription of EMD alarm-1rw DisplayString .1.3.6.1.4.1.2468.1.2.1.1.12.5.1 |
emdConfigAlarm1TypeThe alarm-1 operation typerw Enumeration .1.3.6.1.4.1.2468.1.2.1.1.12.5.2 |
emdConfigAlarm2 OBJECT IDENTIFIER .1.3.6.1.4.1.2468.1.2.1.1.12.6 |
emdConfigAlarm2NameDescription of EMD alarm-2rw DisplayString .1.3.6.1.4.1.2468.1.2.1.1.12.6.1 |
emdConfigAlarm2TypeThe alarm-1 operation typerw Enumeration .1.3.6.1.4.1.2468.1.2.1.1.12.6.2 |
upsTrapGroup OBJECT IDENTIFIER .1.3.6.1.4.1.2468.1.2.1.2 |
ushaPowerRestoredINFORMATION: Utility power has been restore. TRAP-TYPE .1.3.6.1.4.1.2468.1.2.1.2.0.1 |
ushaPowerFailWARNING: Utility power not available. TRAP-TYPE .1.3.6.1.4.1.2468.1.2.1.2.0.2 |
ushaReturnFromLowBatteryINFORMATION: The UPS has return from a low battery condition. TRAP-TYPE .1.3.6.1.4.1.2468.1.2.1.2.0.3 |
ushaLowBatterySEVERE: The UPS batteries are low and will soon be exhausted. TRAP-TYPE .1.3.6.1.4.1.2468.1.2.1.2.0.4 |
ushaUpsOkINFORMATION: The ups is working fine. TRAP-TYPE .1.3.6.1.4.1.2468.1.2.1.2.0.5 |
ushaUpsFailedSEVERE: The ups is not working fine. TRAP-TYPE .1.3.6.1.4.1.2468.1.2.1.2.0.6 |
ushaUpsNotOnBatteryINFORMATION: The UPS is not on battery power. TRAP-TYPE .1.3.6.1.4.1.2468.1.2.1.2.0.7 |
ushaUpsOnBatteryWARNING: The UPS has switched to battery backup power. TRAP-TYPE .1.3.6.1.4.1.2468.1.2.1.2.0.8 |
ushaTestOverINFORMATION: The testing of UPS is completed. TRAP-TYPE .1.3.6.1.4.1.2468.1.2.1.2.0.9 |
ushaTestInProgressINFORMATION: The testing is going on ups. TRAP-TYPE .1.3.6.1.4.1.2468.1.2.1.2.0.10 |
ushaBypassOnINFORMATION: The UPS has enabled bypass. TRAP-TYPE .1.3.6.1.4.1.2468.1.2.1.2.0.11 |
ushaUpsOnlineINFORMATION: The UPS is not on Bypass and return to normal status. TRAP-TYPE .1.3.6.1.4.1.2468.1.2.1.2.0.12 |
ushaCommunicationLostSEVERE: Communication to the UPS has been lost. TRAP-TYPE .1.3.6.1.4.1.2468.1.2.1.2.0.13 |
ushaCommunicationEstablishedINFORMATION: Communication with the UPS has been established. TRAP-TYPE .1.3.6.1.4.1.2468.1.2.1.2.0.14 |
ushaUpsGoingDownWARNING: The ups has been given shutdown command. TRAP-TYPE .1.3.6.1.4.1.2468.1.2.1.2.0.15 |
ushaUpsTurnedOffINFORMATION: UPS turn off. TRAP-TYPE .1.3.6.1.4.1.2468.1.2.1.2.0.16 |
ushaUpsSleepingINFORMATION: UPS has entered sleep mode. TRAP-TYPE .1.3.6.1.4.1.2468.1.2.1.2.0.17 |
ushaUpsWokeUpINFORMATION: The UPS woke up from sleep mode. TRAP-TYPE .1.3.6.1.4.1.2468.1.2.1.2.0.18 |
ushaUpsRebootedINFORMATION: The UPS is reboot. TRAP-TYPE .1.3.6.1.4.1.2468.1.2.1.2.0.19 |
ushaUpsShutdownCancelledINFORMATION: The UPS shutdown process had been cancelled. TRAP-TYPE .1.3.6.1.4.1.2468.1.2.1.2.0.20 |
ushaUpsNotOverTemperatureINFORMATION: The UPS internal temperature return to normal. TRAP-TYPE .1.3.6.1.4.1.2468.1.2.1.2.0.21 |
ushaUpsOverTemperatureSEVERE: The UPS temperature is too high. TRAP-TYPE .1.3.6.1.4.1.2468.1.2.1.2.0.22 |
ushaUpsNotOverLoadINFORMATION: The UPS load return from overload. TRAP-TYPE .1.3.6.1.4.1.2468.1.2.1.2.0.23 |
ushaUpsOverLoadSEVERE: The UPS is overload. TRAP-TYPE .1.3.6.1.4.1.2468.1.2.1.2.0.24 |
ushaUpsModuleInsertedWARNING: UPS Battery Module plug-in. TRAP-TYPE .1.3.6.1.4.1.2468.1.2.1.2.0.25 |
ushaUpsModuleRemovedWARNING: UPS Battery Module unplug. TRAP-TYPE .1.3.6.1.4.1.2468.1.2.1.2.0.26 |
emdTemperatureNotHighINFORMATION: EMD Temperature not over high Set point. TRAP-TYPE .1.3.6.1.4.1.2468.1.2.1.2.0.27 |
emdTemperatureTooHighWARNING: EMD Temperature over high Set point. TRAP-TYPE .1.3.6.1.4.1.2468.1.2.1.2.0.28 |
emdTemperatureNotLowINFORMATION: EMD Temperature not under low Set point. TRAP-TYPE .1.3.6.1.4.1.2468.1.2.1.2.0.29 |
emdTemperatureTooLowWARNING: EMD Temperature under low Set point. TRAP-TYPE .1.3.6.1.4.1.2468.1.2.1.2.0.30 |
emdHumidityNotHighINFORMATION: EMD Humidity not over high Set point. TRAP-TYPE .1.3.6.1.4.1.2468.1.2.1.2.0.31 |
emdHumidityTooHighWARNING: EMD Humidity over high Set point. TRAP-TYPE .1.3.6.1.4.1.2468.1.2.1.2.0.32 |
emdHumidityNotLowINFORMATION: EMD Humidity not under low Set point. TRAP-TYPE .1.3.6.1.4.1.2468.1.2.1.2.0.33 |
emdHumidityTooLowWARNING: EMD Humidity under low Set point. TRAP-TYPE .1.3.6.1.4.1.2468.1.2.1.2.0.34 |
emdAlarm1NormalINFORMATION: EMD Alarm-1 not active. TRAP-TYPE .1.3.6.1.4.1.2468.1.2.1.2.0.35 |
emdAlarm1ActiveWARNING: EMD Alarm-1 activated. TRAP-TYPE .1.3.6.1.4.1.2468.1.2.1.2.0.36 |
emdAlarm2NormalINFORMATION: EMD Alarm-2 not active. TRAP-TYPE .1.3.6.1.4.1.2468.1.2.1.2.0.37 |
emdAlarm2ActiveWARNING: EMD Alarm-2 activated. TRAP-TYPE .1.3.6.1.4.1.2468.1.2.1.2.0.38 |
ushaUpsInternalwarningWARNING: Internal warning. TRAP-TYPE .1.3.6.1.4.1.2468.1.2.1.2.0.39 |
ushaUpsReturnFromInternalwarningINFORMATION: Return from Internal warning. TRAP-TYPE .1.3.6.1.4.1.2468.1.2.1.2.0.40 |
ushaUpsEPOActiveWARNING: EPO Active. TRAP-TYPE .1.3.6.1.4.1.2468.1.2.1.2.0.41 |
ushaUpsReturnFromEPOActiveINFORMATION: Return from EPO Active. TRAP-TYPE .1.3.6.1.4.1.2468.1.2.1.2.0.42 |
ushaUpsModuleUnlockWARNING: Module Unlock. TRAP-TYPE .1.3.6.1.4.1.2468.1.2.1.2.0.43 |
ushaUpsReturnFromModuleUnlockINFORMATION: Return from Module Unlock. TRAP-TYPE .1.3.6.1.4.1.2468.1.2.1.2.0.44 |
ushaUpsMain1NeutrallossWARNING: Main 1 Neutral loss. TRAP-TYPE .1.3.6.1.4.1.2468.1.2.1.2.0.45 |
ushaUpsReturnFromMain1NeutrallossINFORMATION: Return from Main 1 Neutral loss. TRAP-TYPE .1.3.6.1.4.1.2468.1.2.1.2.0.46 |
ushaUpsMain1phaseerrorWARNING: Main 1 phase error. TRAP-TYPE .1.3.6.1.4.1.2468.1.2.1.2.0.47 |
ushaUpsReturnFromMain1phaseerrorINFORMATION: Return from Main 1 phase error. TRAP-TYPE .1.3.6.1.4.1.2468.1.2.1.2.0.48 |
ushaUpsSitefaultWARNING: Site fault. TRAP-TYPE .1.3.6.1.4.1.2468.1.2.1.2.0.49 |
ushaUpsReturnFromSitefaultINFORMATION: Return from Site fault. TRAP-TYPE .1.3.6.1.4.1.2468.1.2.1.2.0.50 |
ushaUpsBypassAbnormalWARNING: Bypass Abnormal. TRAP-TYPE .1.3.6.1.4.1.2468.1.2.1.2.0.51 |
ushaUpsReturnFromBypassAbnormalINFORMATION: Return from Bypass Abnormal. TRAP-TYPE .1.3.6.1.4.1.2468.1.2.1.2.0.52 |
ushaUpsBypassPhaseErrorWARNING: Bypass Phase Error. TRAP-TYPE .1.3.6.1.4.1.2468.1.2.1.2.0.53 |
ushaUpsReturnFromBypassPhaseErrorINFORMATION: Return from Bypass Phase Error. TRAP-TYPE .1.3.6.1.4.1.2468.1.2.1.2.0.54 |
ushaUpsBatteryOpenWARNING: Battery Open. TRAP-TYPE .1.3.6.1.4.1.2468.1.2.1.2.0.55 |
ushaUpsReturnFromBatteryOpenINFORMATION: Return from Battery Open. TRAP-TYPE .1.3.6.1.4.1.2468.1.2.1.2.0.56 |
ushaUpsBatteryOverChargeWARNING: Battery Over Charge. TRAP-TYPE .1.3.6.1.4.1.2468.1.2.1.2.0.57 |
ushaUpsReturnFromBatteryOverChargeINFORMATION: Return from Battery Over Charge. TRAP-TYPE .1.3.6.1.4.1.2468.1.2.1.2.0.58 |
ushaUpsBatteryReverseWARNING: Battery Reverse. TRAP-TYPE .1.3.6.1.4.1.2468.1.2.1.2.0.59 |
ushaUpsReturnFromBatteryReverseINFORMATION: Return from Battery Reverse. TRAP-TYPE .1.3.6.1.4.1.2468.1.2.1.2.0.60 |
ushaUpsOverloadforewarningWARNING: Overload forewarning. TRAP-TYPE .1.3.6.1.4.1.2468.1.2.1.2.0.61 |
ushaUpsReturnFromOverloadforewarningINFORMATION: Return from Overload forewarning. TRAP-TYPE .1.3.6.1.4.1.2468.1.2.1.2.0.62 |
ushaUpsOverloadWarningWARNING: Overload Warning. TRAP-TYPE .1.3.6.1.4.1.2468.1.2.1.2.0.63 |
ushaUpsReturnFromOverloadWarningINFORMATION: Return from Overload Warning. TRAP-TYPE .1.3.6.1.4.1.2468.1.2.1.2.0.64 |
ushaUpsFanLockWARNING: Fan Lock. TRAP-TYPE .1.3.6.1.4.1.2468.1.2.1.2.0.65 |
ushaUpsReturnFromFanLockINFORMATION: Return from Fan Lock. TRAP-TYPE .1.3.6.1.4.1.2468.1.2.1.2.0.66 |
ushaUpsMaintaincoverisopenWARNING: Maintain cover is open. TRAP-TYPE .1.3.6.1.4.1.2468.1.2.1.2.0.67 |
ushaUpsReturnFromMaintaincoverisopenINFORMATION: Return from Maintain cover is open. TRAP-TYPE .1.3.6.1.4.1.2468.1.2.1.2.0.68 |
ushaUpsChargerfaultWARNING: Charger fault. TRAP-TYPE .1.3.6.1.4.1.2468.1.2.1.2.0.69 |
ushaUpsReturnFromChargerfaultINFORMATION: Return from Charger fault. TRAP-TYPE .1.3.6.1.4.1.2468.1.2.1.2.0.70 |
ushaUpsModulelocationerrorWARNING: Module location error. TRAP-TYPE .1.3.6.1.4.1.2468.1.2.1.2.0.71 |
ushaUpsReturnFromModulelocationerrorINFORMATION: Return from Module location error. TRAP-TYPE .1.3.6.1.4.1.2468.1.2.1.2.0.72 |
ushaUpsTurnonabnormalWARNING: Turn on abnormal. TRAP-TYPE .1.3.6.1.4.1.2468.1.2.1.2.0.73 |
ushaUpsReturnFromTurnonabnormalINFORMATION: Return from Turn on abnormal. TRAP-TYPE .1.3.6.1.4.1.2468.1.2.1.2.0.74 |
ushaUpsRedundancylossWARNING: Redundancy loss. TRAP-TYPE .1.3.6.1.4.1.2468.1.2.1.2.0.75 |
ushaUpsReturnFromRedundancylossINFORMATION: Return from Redundancy loss. TRAP-TYPE .1.3.6.1.4.1.2468.1.2.1.2.0.76 |
ushaUpsHotSwapActivedWARNING: Hot Swap Actived. TRAP-TYPE .1.3.6.1.4.1.2468.1.2.1.2.0.77 |
ushaUpsReturnFromHotSwapActivedINFORMATION: Return from Hot Swap Actived. TRAP-TYPE .1.3.6.1.4.1.2468.1.2.1.2.0.78 |
ushaUpsBatteryInformWARNING: Battery Inform. TRAP-TYPE .1.3.6.1.4.1.2468.1.2.1.2.0.79 |
ushaUpsReturnFromBatteryInformINFORMATION: Return from Battery Inform. TRAP-TYPE .1.3.6.1.4.1.2468.1.2.1.2.0.80 |
ushaUpsInspectionInformWARNING: Inspection Inform. TRAP-TYPE .1.3.6.1.4.1.2468.1.2.1.2.0.81 |
ushaUpsReturnFromInspectionInformINFORMATION: Return from Inspection Inform. TRAP-TYPE .1.3.6.1.4.1.2468.1.2.1.2.0.82 |
ushaUpsGuaranteeInformWARNING: Guarantee Inform. TRAP-TYPE .1.3.6.1.4.1.2468.1.2.1.2.0.83 |
ushaUpsReturnFromGuaranteeInformINFORMATION: Return from Guarantee Inform. TRAP-TYPE .1.3.6.1.4.1.2468.1.2.1.2.0.84 |
ushaUpsTemperatureLowWARNING: Temperature Low. TRAP-TYPE .1.3.6.1.4.1.2468.1.2.1.2.0.85 |
ushaUpsReturnFromTemperatureLowINFORMATION: Return from Temperature Low. TRAP-TYPE .1.3.6.1.4.1.2468.1.2.1.2.0.86 |
ushaUpsTemperatureHighWARNING: Temperature High. TRAP-TYPE .1.3.6.1.4.1.2468.1.2.1.2.0.87 |
ushaUpsReturnFromTemperatureHighINFORMATION: Return from Temperature High. TRAP-TYPE .1.3.6.1.4.1.2468.1.2.1.2.0.88 |
ushaUpsBatteryOverTemperatureWARNING: Battery Over Temperature. TRAP-TYPE .1.3.6.1.4.1.2468.1.2.1.2.0.89 |
ushaUpsReturnFromBatteryOverTemperatureINFORMATION: Return from Battery Over Temperature. TRAP-TYPE .1.3.6.1.4.1.2468.1.2.1.2.0.90 |
ushaUpsFanMaintainInformWARNING: Fan Maintain Inform. TRAP-TYPE .1.3.6.1.4.1.2468.1.2.1.2.0.91 |
ushaUpsReturnFromFanMaintainInformINFORMATION: Return from Fan Maintain Inform. TRAP-TYPE .1.3.6.1.4.1.2468.1.2.1.2.0.92 |
ushaUpsBusCapacitanceMaintainInformWARNING: Bus Capacitance Maintain Inform. TRAP-TYPE .1.3.6.1.4.1.2468.1.2.1.2.0.93 |
ushaUpsReturnFromBusCapacitanceMaintainInformINFORMATION: Return from Bus Capacitance Maintain Inform. TRAP-TYPE .1.3.6.1.4.1.2468.1.2.1.2.0.94 |
ushaUpsSystemOverCapacityWARNING: System Over Capacity. TRAP-TYPE .1.3.6.1.4.1.2468.1.2.1.2.0.95 |
ushaUpsReturnFromSystemOverCapacityINFORMATION: Return from System Over Capacity. TRAP-TYPE .1.3.6.1.4.1.2468.1.2.1.2.0.96 |