SLE-PM-MIB
This MIB contains all needed informations about Performance Manager.
Main OID:
slePmMgr.1.3.6.1.4.1.6296.101.94
67
Objects
Active
Status
4
Dependencies
Imported Objects
Objects
67 total| Object Name |
|---|
slePmMgrThis MIB contains all needed informations about Performance Manager. MODULE-IDENTITY .1.3.6.1.4.1.6296.101.94 |
slePmNeIdsystem MAC addressro OCTET STRING .1.3.6.1.4.1.6296.101.94.1 |
slePmConfigBase OBJECT IDENTIFIER .1.3.6.1.4.1.6296.101.94.2 |
slePmConfigTableThis table is the Performance Config table. It gets populated when system init is done. And it contains all the class performance supported for the device SEQUENCE OF SlePmConfigEntry .1.3.6.1.4.1.6296.101.94.2.1 |
slePmConfigEntry SlePmConfigEntry .1.3.6.1.4.1.6296.101.94.2.1.1 |
slePmConfigSeqIdDescription.ro INTEGER .1.3.6.1.4.1.6296.101.94.2.1.1.1 |
slePmConfigClassIdClass ID starts from 1 to 255 for the system. And these IDs are generated internallyro PmClassId .1.3.6.1.4.1.6296.101.94.2.1.1.2 |
slePmConfigPmIdCurrent PM IDro PmId .1.3.6.1.4.1.6296.101.94.2.1.1.3 |
slePmConfigSource|type|length|value|type|length|value|.... type (1-byte) : PM location type length(1-byte) : PM location value length value (length-bytes) : PM location valuero PmSrc .1.3.6.1.4.1.6296.101.94.2.1.1.4 |
slePmConfigTcaStatTCA status TCA Normal (0) TCA Occur (1)ro Enumeration .1.3.6.1.4.1.6296.101.94.2.1.1.5 |
slePmConfigTcaEnableTCA enable Confguration : enabled or disabled. Enable(1) : TCA State is Enabled. Hence TRAPs will be sent for this. Disable(0) : TCA State is Disabled. So TCA won't be notified to user.ro PmTcaState .1.3.6.1.4.1.6296.101.94.2.1.1.6 |
slePmConfigTh15Min15minute Performance TCA threshold configuration countro Counter64 .1.3.6.1.4.1.6296.101.94.2.1.1.7 |
slePmConfigTh1Day1day Performance TCA threshold configuration countrw Counter64 .1.3.6.1.4.1.6296.101.94.2.1.1.8 |
slePmConfigControl OBJECT IDENTIFIER .1.3.6.1.4.1.6296.101.94.2.2 |
slePmConfigControlRequestThe configuration commands, and user can configure functions via setting this entry as proper value.rw Enumeration .1.3.6.1.4.1.6296.101.94.2.2.1 |
slePmConfigControlStatusstatus of user command. User have to check this value as .busy. or .idle. before do setRequest.ro SleControlStatusType (SLE-TC-MIB) .1.3.6.1.4.1.6296.101.94.2.2.2 |
slePmConfigControlTimerthe wait-time until setRequest end. In case of short-time command, this value is 0rw Gauge32 .1.3.6.1.4.1.6296.101.94.2.2.3 |
slePmConfigControlTimeStampthe time stamp of the last command. (don.t care)ro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.6296.101.94.2.2.4 |
slePmConfigControlReqResultResult of the last command.ro SleControlRequestResultType (SLE-TC-MIB) .1.3.6.1.4.1.6296.101.94.2.2.5 |
slePmConfigControlSeqIdPM Manager Class IDrw Integer32 .1.3.6.1.4.1.6296.101.94.2.2.6 |
slePmConfigControlTcaEnableTCA enable Confguration : enabled or disabled. Enable(1) : TCA State is Enabled. Hence TRAPs will be sent for this. Disable(0) : TCA State is Disabled. So TCA won't be notified to user.rw PmTcaState .1.3.6.1.4.1.6296.101.94.2.2.7 |
slePmConfigControlTh15Min15minute Performance TCA threshold configuration countrw Counter64 .1.3.6.1.4.1.6296.101.94.2.2.8 |
slePmConfigControlTh1Day1day Performance TCA threshold configuration countrw Counter64 .1.3.6.1.4.1.6296.101.94.2.2.9 |
slePmConfigNotification OBJECT IDENTIFIER .1.3.6.1.4.1.6296.101.94.2.3 |
slePmConfigTcaEnableChangedNotification for Tca Enable change NOTIFICATION-TYPE .1.3.6.1.4.1.6296.101.94.2.3.1 |
slePmConfigTh15MinChangedNotification for 15minute theshold change NOTIFICATION-TYPE .1.3.6.1.4.1.6296.101.94.2.3.2 |
slePmConfigTh1DayChangedNotification for 1day theshold change NOTIFICATION-TYPE .1.3.6.1.4.1.6296.101.94.2.3.3 |
slePmCurrentBase OBJECT IDENTIFIER .1.3.6.1.4.1.6296.101.94.3 |
slePmCurrentTableThis table contains the current PM count. SEQUENCE OF SlePmCurrentEntry .1.3.6.1.4.1.6296.101.94.3.1 |
slePmCurrentEntry SlePmCurrentEntry .1.3.6.1.4.1.6296.101.94.3.1.1 |
slePmCurrentSeqIdDescription.ro INTEGER .1.3.6.1.4.1.6296.101.94.3.1.1.1 |
slePmCurrentClassIdCurrent Class IDro PmClassId .1.3.6.1.4.1.6296.101.94.3.1.1.2 |
slePmCurrentPmIdCurrent PM IDro PmId .1.3.6.1.4.1.6296.101.94.3.1.1.3 |
slePmCurrentSource|type|length|value|type|length|value|.... type (1-byte) : PM location type length(1-byte) : PM location value length value (length-bytes) : PM location valuero PmSrc .1.3.6.1.4.1.6296.101.94.3.1.1.4 |
slePmCurrentTermDescription.rw Enumeration .1.3.6.1.4.1.6296.101.94.3.1.1.5 |
slePmCurrentPmCountCurrent Performance countro Counter64 .1.3.6.1.4.1.6296.101.94.3.1.1.6 |
slePmCurrentAccSecondCurrent Performance data accumulation seconds(count)ro Counter32 .1.3.6.1.4.1.6296.101.94.3.1.1.7 |
slePmCurrentTcaStatTCA status TCA Normal (0) TCA Occur (1)ro Enumeration .1.3.6.1.4.1.6296.101.94.3.1.1.8 |
slePmCurrentTcaTimeCurrent PM Time and Datero TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.6296.101.94.3.1.1.9 |
slePmCurrentControl OBJECT IDENTIFIER .1.3.6.1.4.1.6296.101.94.3.2 |
slePmCurrentControlRequestThe configuration commands, and user can configure functions via setting this entry as proper value. clearCurrentPm(1): Clears the current Performance count (both 15min and 1day) PM history(accumulation) count is not cleared clearCurrentTca(2): Clears the current Performance TCA flag (both 15min and 1day)rw Enumeration .1.3.6.1.4.1.6296.101.94.3.2.1 |
slePmCurrentControlStatusstatus of user command. User have to check this value as .busy. or .idle. before do setRequest.ro SleControlStatusType (SLE-TC-MIB) .1.3.6.1.4.1.6296.101.94.3.2.2 |
slePmCurrentControlTimerthe wait-time until setRequest end. In case of short-time command, this value is 0rw Gauge32 .1.3.6.1.4.1.6296.101.94.3.2.3 |
slePmCurrentControlTimeStampthe time stamp of the last command. (don.t care)ro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.6296.101.94.3.2.4 |
slePmCurrentControlReqResultResult of the last command.ro SleControlRequestResultType (SLE-TC-MIB) .1.3.6.1.4.1.6296.101.94.3.2.5 |
slePmCurrentNotification OBJECT IDENTIFIER .1.3.6.1.4.1.6296.101.94.3.3 |
slePmCurrentPmClearedNotification for current PM clear NOTIFICATION-TYPE .1.3.6.1.4.1.6296.101.94.3.3.1 |
slePMHistoryBase OBJECT IDENTIFIER .1.3.6.1.4.1.6296.101.94.4 |
slePmHistoryTableThis Table is used to for keeping the PM History SEQUENCE OF SlePmHistoryEntry .1.3.6.1.4.1.6296.101.94.4.1 |
slePmHistoryEntry SlePmHistoryEntry .1.3.6.1.4.1.6296.101.94.4.1.1 |
slePmHistorySeqIdDescription.ro INTEGER .1.3.6.1.4.1.6296.101.94.4.1.1.1 |
slePmHistoryClassIdHistory Class ID.ro PmClassId .1.3.6.1.4.1.6296.101.94.4.1.1.2 |
slePmHistoryPmIdHistory PM Idro PmId .1.3.6.1.4.1.6296.101.94.4.1.1.3 |
slePmHistoryPmSource|type|length|value|type|length|value|.... type (1-byte) : PM location type length(1-byte) : PM location value length value (length-bytes) : PM location valuero PmSrc .1.3.6.1.4.1.6296.101.94.4.1.1.4 |
slePmHistoryTermDescription.ro Enumeration .1.3.6.1.4.1.6296.101.94.4.1.1.5 |
slePmHistoryIndexHistory Index: 15min : 1 ~ 96, 1-day : 1 ~ 7ro INTEGER .1.3.6.1.4.1.6296.101.94.4.1.1.6 |
slePmHistoryPmCountHistory Performance countro Counter64 .1.3.6.1.4.1.6296.101.94.4.1.1.7 |
slePmHistoryAccCountDescription.rw Counter32 .1.3.6.1.4.1.6296.101.94.4.1.1.8 |
slePmHistoryStartTimeDescription.ro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.6296.101.94.4.1.1.9 |
slePmHistoryControl OBJECT IDENTIFIER .1.3.6.1.4.1.6296.101.94.4.2 |
slePmHistoryControlRequestThe configuration commands, and user can configure functions via setting this entry as proper value. clearPmHistory : clears all the PM History Tablerw Enumeration .1.3.6.1.4.1.6296.101.94.4.2.1 |
slePmHistoryControlStatusstatus of user command. User have to check this value as .busy. or .idle. before do setRequest.ro SleControlStatusType (SLE-TC-MIB) .1.3.6.1.4.1.6296.101.94.4.2.2 |
slePmHistoryControlTimerthe wait-time until setRequest end. In case of short-time command, this value is 0rw Gauge32 .1.3.6.1.4.1.6296.101.94.4.2.3 |
slePmHistoryControlTimeStampthe time stamp of the last command. (don.t care)ro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.6296.101.94.4.2.4 |
slePmHistoryControlReqResultResult of the last command.ro SleControlRequestResultType (SLE-TC-MIB) .1.3.6.1.4.1.6296.101.94.4.2.5 |
slePmHistoryNotification OBJECT IDENTIFIER .1.3.6.1.4.1.6296.101.94.4.3 |
slePmHistoryPmClearedNotification for PM History cleared NOTIFICATION-TYPE .1.3.6.1.4.1.6296.101.94.4.3.1 |
More MIBs from Dasan
Browse all DasanMIBs →SLE-GPON-MIB
SNMP MIB module
4401 objects→
SLE-FAULTMGMT-MIB
The SLE-FAULTMGMT-MIB module provides the SNMP interface for monitoring and managing alarm states, fault conditions, and logical entity health within SLE (Service Level Enforcement) network devices. It enables the retrieval of specific fault metrics, including alarm severity levels, timestamps, and the operational status of logical service entities to facilitate automated incident detection and remediation.
2107 objects→
SLE-EPON-MIB
SNMP MIB module
2086 objects→
SLEV2-MULTICAST-MIB
Standard SNMP MIB module defining data structures for SLEV2-MULTICAST-MIB.
1985 objects→
SLE-BRIDGE-MIB
SNMP MIB module
1811 objects→
SLEV2-DHCP-MIB
SNMP MIB module
949 objects→