SLE-NETWORK-MIB
AI MIB Summary
The SLE-NETWORK-MIB module facilitates the monitoring and management of DHCP server operations and vendor-specific SLE DHCP features on SUSE Linux Enterprise systems. It exposes critical metrics including active lease counts, address pool utilization, and the status of proprietary DHCP extensions to enable precise network service administration.
This MIB contains all needed informations about DHCP and all supported sle DHCP features.
Main OID:
sleNetwork.1.3.6.1.4.1.6296.101.11
459
Objects
Active
Status
8
Dependencies
Imported Objects
Objects
459 total| Object Name |
|---|
sleNetworkThis MIB contains all needed informations about DHCP and all supported sle DHCP features. MODULE-IDENTITY .1.3.6.1.4.1.6296.101.11 |
sleNetInterface OBJECT IDENTIFIER .1.3.6.1.4.1.6296.101.11.1 |
sleNetIfTableDescription. SEQUENCE OF SleNetIfEntry .1.3.6.1.4.1.6296.101.11.1.1 |
sleNetIfEntryDescription. SleNetIfEntry .1.3.6.1.4.1.6296.101.11.1.1.1 |
sleNetIfIndexNetwork interface index 0 : any(all) 1..4094 : VLAN 4095 : management 4096 : loopback 4097 : NULL device 10000..11023: Tunnel interface indexro Integer32 .1.3.6.1.4.1.6296.101.11.1.1.1.1 |
sleNetIfNameDevice Name of this Interface.ro OCTET STRING .1.3.6.1.4.1.6296.101.11.1.1.1.2 |
sleNetIfDescriptionDescription of this interface.ro OCTET STRING .1.3.6.1.4.1.6296.101.11.1.1.1.3 |
sleNetIfTableIndexSame as ifIndex (for appropriated ifTable entries).ro InterfaceIndex (IF-MIB) .1.3.6.1.4.1.6296.101.11.1.1.1.4 |
sleNetIfRegStateRegistered state of Network device.ro Enumeration .1.3.6.1.4.1.6296.101.11.1.1.1.5 |
sleNetIfAdminStateAdministrative state. down - shutdown up - noshutdownro Enumeration .1.3.6.1.4.1.6296.101.11.1.1.1.6 |
sleNetIfOperStateOperational state. down - shutdown or not running up - runningro Enumeration .1.3.6.1.4.1.6296.101.11.1.1.1.7 |
sleNetIfMulticastMulticast enable/disable state.ro Enumeration .1.3.6.1.4.1.6296.101.11.1.1.1.8 |
sleNetIfMtuMaximum Transmission Unit.ro INTEGER .1.3.6.1.4.1.6296.101.11.1.1.1.9 |
sleNetIfIpSetModeIP address setting mode. 0 : static 1 : dynamic (by DHCP client)ro Enumeration .1.3.6.1.4.1.6296.101.11.1.1.1.10 |
sleNetIfIpMartianFilterDescription.ro Enumeration .1.3.6.1.4.1.6296.101.11.1.1.1.11 |
sleNetIfUpCntThe times of link-up event.ro Integer32 .1.3.6.1.4.1.6296.101.11.1.1.1.12 |
sleNetIfDownCntThe times of link-down event.ro Integer32 .1.3.6.1.4.1.6296.101.11.1.1.1.13 |
sleNetIfLinkUpTimeThe elapsed time after link is up.ro Counter64 UNITS "1 sec" .1.3.6.1.4.1.6296.101.11.1.1.1.14 |
sleNetIfElapsedTimeAfterClearStatsThe elapsed time after clearing status.ro Counter64 UNITS "1 sec" .1.3.6.1.4.1.6296.101.11.1.1.1.15 |
sleNetIfBindingVRFNameVRF name that this tunnel interface is binding.ro OCTET STRING .1.3.6.1.4.1.6296.101.11.1.1.1.16 |
sleNetIfOnFailUseVRFLookup into a global routing table when the VRF routing table lookup was failed.ro Enumeration .1.3.6.1.4.1.6296.101.11.1.1.1.17 |
sleNetIfIpUnreachabilityIP unreachability ON/OFFro Enumeration .1.3.6.1.4.1.6296.101.11.1.1.1.18 |
sleNetIfipRedirectsDescription.ro Enumeration .1.3.6.1.4.1.6296.101.11.1.1.1.19 |
sleNetIfIpForwardingThe IP forwarding statusro Enumeration .1.3.6.1.4.1.6296.101.11.1.1.1.20 |
sleNetIfAliaslias Name for the Interfacero OCTET STRING .1.3.6.1.4.1.6296.101.11.1.1.1.21 |
sleNetIfIpArpAliasIP Arp Alias statero Enumeration .1.3.6.1.4.1.6296.101.11.1.1.1.22 |
sleNetIfIpArpAliasMacIP Arp Alias MACro MacAddress (SNMPv2-TC) .1.3.6.1.4.1.6296.101.11.1.1.1.23 |
sleNetIfArpMCProbeCountARP request Multicast probe countro Integer32 .1.3.6.1.4.1.6296.101.11.1.1.1.24 |
sleNetIfArpUCProbeCountARP request Unicast probe countro Integer32 .1.3.6.1.4.1.6296.101.11.1.1.1.25 |
sleNetIfArpRetransTimeRetrans time of ARP request (unit: 1s)ro Integer32 .1.3.6.1.4.1.6296.101.11.1.1.1.26 |
sleNetIfIpProxyArpIP Proxy Arp statero Enumeration .1.3.6.1.4.1.6296.101.11.1.1.1.27 |
sleNetIfIpRPFilterIP Reverse Path Filtering of CPUro Enumeration .1.3.6.1.4.1.6296.101.11.1.1.1.28 |
sleNetIfRPFilterReverse Path Filtering of CHIP (default : looseAllow)ro Enumeration .1.3.6.1.4.1.6296.101.11.1.1.1.29 |
sleNetIfRouteMapIP Policy route-map namero OCTET STRING .1.3.6.1.4.1.6296.101.11.1.1.1.30 |
sleNetIfControl OBJECT IDENTIFIER .1.3.6.1.4.1.6296.101.11.1.2 |
sleNetIfControlRequestThe request of a user command.rw Enumeration .1.3.6.1.4.1.6296.101.11.1.2.1 |
sleNetIfControlStatusThe status of a user command.ro SleControlStatusType (SLE-TC-MIB) .1.3.6.1.4.1.6296.101.11.1.2.2 |
sleNetIfControlTimerThe maximum wait time for the manager for a long running user command.rw Gauge32 .1.3.6.1.4.1.6296.101.11.1.2.3 |
sleNetIfControlTimeStampThe time stamp of the last command (end of command).ro SleControlRequestResultType (SLE-TC-MIB) .1.3.6.1.4.1.6296.101.11.1.2.4 |
sleNetIfControlReqResultThe result of the last user command.ro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.6296.101.11.1.2.5 |
sleNetIfControlIndexNetwork interface index 0 : any(all) 1..4094 : VLAN 4095 : management 4096 : loopback 4097 : NULL device 10000..11023: Tunnel interface indexrw Integer32 .1.3.6.1.4.1.6296.101.11.1.2.6 |
sleNetIfControlDescriptionDescription of this interface.rw OCTET STRING .1.3.6.1.4.1.6296.101.11.1.2.7 |
sleNetIfControlRegStateDescription.rw Enumeration .1.3.6.1.4.1.6296.101.11.1.2.8 |
sleNetIfControlAdminStateAdministrative state.rw Enumeration .1.3.6.1.4.1.6296.101.11.1.2.9 |
sleNetIfControlMulticastMulticast enable/disable state.rw Enumeration .1.3.6.1.4.1.6296.101.11.1.2.10 |
sleNetIfControlMtuMaximum Transmission Unit.rw INTEGER .1.3.6.1.4.1.6296.101.11.1.2.11 |
sleNetIfControlIpMartianFilterDescription.rw Enumeration .1.3.6.1.4.1.6296.101.11.1.2.12 |
sleNetIfControlBindingVRFNameVRF name that this tunnel interface is binding.rw OCTET STRING .1.3.6.1.4.1.6296.101.11.1.2.13 |
sleNetIfControlOnFailUseVRFLookup into a global routing table when the VRF routing table lookup was failed.rw Enumeration .1.3.6.1.4.1.6296.101.11.1.2.14 |
sleNetIfControlIpUnreachabilityIP unreachability ON/OFFrw Enumeration .1.3.6.1.4.1.6296.101.11.1.2.15 |
sleNetIfControlIpRedirectsDescription.rw Enumeration .1.3.6.1.4.1.6296.101.11.1.2.16 |
sleNetIfControlIpForwardingThe IP forwarding statusrw Enumeration .1.3.6.1.4.1.6296.101.11.1.2.17 |
sleNetIfControlAliasAlias Name for the Interfacerw OCTET STRING .1.3.6.1.4.1.6296.101.11.1.2.18 |
sleNetIfControlIpArpAliasIP Arp Alias staterw Enumeration .1.3.6.1.4.1.6296.101.11.1.2.19 |
sleNetIfControlIpArpAliasMacIP Arp Alias MACrw MacAddress (SNMPv2-TC) .1.3.6.1.4.1.6296.101.11.1.2.20 |
sleNetIfControlArpMCProbeCountARP request Multicast probe countrw Integer32 .1.3.6.1.4.1.6296.101.11.1.2.21 |
sleNetIfControlArpUCProbeCountARP request Unicast probe countrw Integer32 .1.3.6.1.4.1.6296.101.11.1.2.22 |
sleNetIfControlArpRetransTimeRetrans time of ARP request (unit: 1s)rw Integer32 .1.3.6.1.4.1.6296.101.11.1.2.23 |
sleNetIfControlIpProxyArpIP Proxy Arp staterw Enumeration .1.3.6.1.4.1.6296.101.11.1.2.24 |
sleNetIfControlIpRPFilterIP Reverse Path Filtering of CPUrw Enumeration .1.3.6.1.4.1.6296.101.11.1.2.25 |
sleNetIfControlRPFilterReverse Path Filtering of CHIP (default : looseAllow)rw Enumeration .1.3.6.1.4.1.6296.101.11.1.2.26 |
sleNetIfControlRouteMapIP Policy route-map namerw OCTET STRING .1.3.6.1.4.1.6296.101.11.1.2.27 |
sleNetIfNotification OBJECT IDENTIFIER .1.3.6.1.4.1.6296.101.11.1.3 |
sleNetIfRegStateChangedDescription. NOTIFICATION-TYPE .1.3.6.1.4.1.6296.101.11.1.3.1 |
sleNetIfProfileChangedsetNetIfProfile. NOTIFICATION-TYPE .1.3.6.1.4.1.6296.101.11.1.3.2 |
sleNetIfIpMartianFilterChangedDescription. NOTIFICATION-TYPE .1.3.6.1.4.1.6296.101.11.1.3.3 |
sleNetIfBindingVRFSetDescription. NOTIFICATION-TYPE .1.3.6.1.4.1.6296.101.11.1.3.4 |
sleNetIfBindingVRFUnsetDescription. NOTIFICATION-TYPE .1.3.6.1.4.1.6296.101.11.1.3.5 |
sleNetIfIpOnFailUseVRFChangedDescription. NOTIFICATION-TYPE .1.3.6.1.4.1.6296.101.11.1.3.6 |
sleNetIfIpUnreachabilityChangedDescription. NOTIFICATION-TYPE .1.3.6.1.4.1.6296.101.11.1.3.7 |
sleNetIfIpRedirectsChangedDescription. NOTIFICATION-TYPE .1.3.6.1.4.1.6296.101.11.1.3.8 |
sleNetIfIpForwardingChangedsetNetIfIpForwarding NOTIFICATION-TYPE .1.3.6.1.4.1.6296.101.11.1.3.9 |
sleNetIfAliasChangedsetAlias NOTIFICATION-TYPE .1.3.6.1.4.1.6296.101.11.1.3.10 |
sleNetIfIpArpAliasChangedsetIpArpAlias NOTIFICATION-TYPE .1.3.6.1.4.1.6296.101.11.1.3.11 |
sleNetIfArpMCProbeCountChangedsetArpMCProbeCount NOTIFICATION-TYPE .1.3.6.1.4.1.6296.101.11.1.3.12 |
sleNetIfArpUCProbeCountChangedsetArpUCProbeCount NOTIFICATION-TYPE .1.3.6.1.4.1.6296.101.11.1.3.13 |
sleNetIfArpRetransTimeChangedsetArpRetransTime NOTIFICATION-TYPE .1.3.6.1.4.1.6296.101.11.1.3.14 |
sleNetIfIpProxyArpChangedsetIpProxyArp NOTIFICATION-TYPE .1.3.6.1.4.1.6296.101.11.1.3.15 |
sleNetIfIpRPFilterChangedsetIpRPFilter NOTIFICATION-TYPE .1.3.6.1.4.1.6296.101.11.1.3.16 |
sleNetIfRPFilterChangedsetRPFilter NOTIFICATION-TYPE .1.3.6.1.4.1.6296.101.11.1.3.17 |
sleNetIfRouteMapChangedsetRouteMap NOTIFICATION-TYPE .1.3.6.1.4.1.6296.101.11.1.3.18 |
sleIpAddress OBJECT IDENTIFIER .1.3.6.1.4.1.6296.101.11.2 |
sleIpAddrTableDescription. SEQUENCE OF SleIpAddrEntry .1.3.6.1.4.1.6296.101.11.2.1 |
sleIpAddrEntryDescription. SleIpAddrEntry .1.3.6.1.4.1.6296.101.11.2.1.1 |
sleIpAddrValueThe IP address to which this entry's addressing information pertains.ro IpAddress .1.3.6.1.4.1.6296.101.11.2.1.1.1 |
sleIpAddrMaskThe subnet mask associated with the IP address of this entry. The value of the mask is an IP address with all the network bits set to 1 and all the hosts bits set to 0.ro Integer32 .1.3.6.1.4.1.6296.101.11.2.1.1.2 |
sleIpAddrBcastThe value of the least-significant bit in the IP broadcast address used for sending datagrams on the (logical) interface associated with the IP address of this entry. For example, when the Internet standard all-ones broadcast address is used, the value will be 1. This value applies to both the subnet and network broadcasts addresses used by the entity on this (logical) interface.ro IpAddress .1.3.6.1.4.1.6296.101.11.2.1.1.3 |
sleIpAddrFlagDescription.ro Bits .1.3.6.1.4.1.6296.101.11.2.1.1.4 |
sleIpAddrScopeDescription.ro Enumeration .1.3.6.1.4.1.6296.101.11.2.1.1.5 |
sleIpAddrIpIndexThe Ip index for Interface Unnumbered feature enhanced. If Interface Unnumbered enhanced feature is enabled on a point-to-point interface. It will get a ip address of a specific interface. Interface unnumbered default setting - it get primary ip address. Interface unnumbered enhanced setting - it get secondary ip address with ip-index. (cf. primary ip address's ip-index : 1. no setting: 0. other setting: 2-1024)ro INTEGER .1.3.6.1.4.1.6296.101.11.2.1.1.6 |
sleIpAddrUnnumUsedIpThe Check a specific IP address for using interface unnumbered feature.ro Enumeration .1.3.6.1.4.1.6296.101.11.2.1.1.7 |
sleIpAddrControl OBJECT IDENTIFIER .1.3.6.1.4.1.6296.101.11.2.2 |
sleIpAddrControlRequestThe request of a user command.rw Enumeration .1.3.6.1.4.1.6296.101.11.2.2.1 |
sleIpAddrControlStatusThe status of a user command.ro SleControlStatusType (SLE-TC-MIB) .1.3.6.1.4.1.6296.101.11.2.2.2 |
sleIpAddrControlTimerThe maximum wait time for the manager for a long running user command.rw Gauge32 .1.3.6.1.4.1.6296.101.11.2.2.3 |
sleIpAddrControlTimeStampThe time stamp of the last command (end of command).ro SleControlRequestResultType (SLE-TC-MIB) .1.3.6.1.4.1.6296.101.11.2.2.4 |
sleIpAddrControlReqResultThe result of the last user command.ro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.6296.101.11.2.2.5 |
sleIpAddrControlNetIfIndexNetwork interface index 1..4094 : VLAN 10000..11023: Tunnel interface indexrw Integer32 (1..4094 | 10000..11023) .1.3.6.1.4.1.6296.101.11.2.2.6 |
sleIpAddrControlValueThe IP address to which this entry's addressing information pertains.rw IpAddress .1.3.6.1.4.1.6296.101.11.2.2.7 |
sleIpAddrControlMaskThe subnet mask associated with the IP address of this entry.rw Integer32 .1.3.6.1.4.1.6296.101.11.2.2.8 |
sleIpAddrControlFlagDescription.rw Enumeration .1.3.6.1.4.1.6296.101.11.2.2.9 |
sleIpAddrControlScopeDescription.rw Enumeration .1.3.6.1.4.1.6296.101.11.2.2.10 |
sleIpAddrControlIpIndexThe Ip index for Interface Unnumbered feature enhanced. If Interface Unnumbered enhanced feature is enabled on a point-to-point interface. It will get a ip address of a specific interface. Interface unnumbered default setting - it get primary ip address. Interface unnumbered enhanced setting - it get secondary ip address with ip-index. (cf. primary ip address's ip-index : 1. no setting: 0. other setting: 2-1024)rw INTEGER .1.3.6.1.4.1.6296.101.11.2.2.11 |
sleIpAddrNotification OBJECT IDENTIFIER .1.3.6.1.4.1.6296.101.11.2.3 |
sleIpAddressCreatedcreateIpAddress. NOTIFICATION-TYPE .1.3.6.1.4.1.6296.101.11.2.3.1 |
sleIpAddressDestroyeddestroyIpAddress. NOTIFICATION-TYPE .1.3.6.1.4.1.6296.101.11.2.3.2 |
sleIpAddressIpIndexAddedaddIpIndex NOTIFICATION-TYPE .1.3.6.1.4.1.6296.101.11.2.3.3 |
sleIpAddressIpIndexDeleteddelIpIndex NOTIFICATION-TYPE .1.3.6.1.4.1.6296.101.11.2.3.4 |
sleArp OBJECT IDENTIFIER .1.3.6.1.4.1.6296.101.11.3 |
sleArpTableDescription. SEQUENCE OF SleArpEntry .1.3.6.1.4.1.6296.101.11.3.1 |
sleArpEntryDescription. SleArpEntry .1.3.6.1.4.1.6296.101.11.3.1.1 |
sleArpIpAddressThe NetworkAddress (e.g., the IP address) corresponding to the media-dependent `physical' address.ro IpAddress .1.3.6.1.4.1.6296.101.11.3.1.1.1 |
sleArpPhyAddressThe media-dependent `physical' address.ro MacAddress (SNMPv2-TC) .1.3.6.1.4.1.6296.101.11.3.1.1.2 |
sleArpPortIndexThe interface on which this entry's equivalence is effective. 0: for any ports.ro Integer32 .1.3.6.1.4.1.6296.101.11.3.1.1.3 |
sleArpStateArp entry's currently status.ro Enumeration .1.3.6.1.4.1.6296.101.11.3.1.1.4 |
sleArpHwTypeHardware Type of media.ro Enumeration .1.3.6.1.4.1.6296.101.11.3.1.1.5 |
sleArpHwUsedArp entry's currently chip usage state.ro Enumeration .1.3.6.1.4.1.6296.101.11.3.1.1.6 |
sleArpUsedTimeArp entry's chip used time.(if sleArpState is 0, always 0 and if sleArpHwUsed is 0, always 0.)ro INTEGER .1.3.6.1.4.1.6296.101.11.3.1.1.7 |
sleArpControl OBJECT IDENTIFIER .1.3.6.1.4.1.6296.101.11.3.2 |
sleArpControlRequestThe request of a user command.rw Enumeration .1.3.6.1.4.1.6296.101.11.3.2.1 |
sleArpControlStatusThe status of a user command.ro SleControlStatusType (SLE-TC-MIB) .1.3.6.1.4.1.6296.101.11.3.2.2 |
sleArpControlTimerThe maximum wait time for the manager for a long running user command.rw Gauge32 .1.3.6.1.4.1.6296.101.11.3.2.3 |
sleArpControlTimeStampThe time stamp of the last command (end of command).ro SleControlRequestResultType (SLE-TC-MIB) .1.3.6.1.4.1.6296.101.11.3.2.4 |
sleArpControlReqResultThe result of the last user command.ro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.6296.101.11.3.2.5 |
sleArpControlNetIfIndexNetwork interface index.rw Integer32 .1.3.6.1.4.1.6296.101.11.3.2.6 |
sleArpControlIpAddressThe NetworkAddress (e.g., the IP address) corresponding to the media-dependent `physical' address.rw IpAddress .1.3.6.1.4.1.6296.101.11.3.2.7 |
sleArpControlPhyAddressThe media-dependent `physical' address.rw MacAddress (SNMPv2-TC) .1.3.6.1.4.1.6296.101.11.3.2.8 |
sleArpControlStateArp entry's currently status.rw Enumeration .1.3.6.1.4.1.6296.101.11.3.2.9 |
sleArpControlMaskDescription.rw INTEGER .1.3.6.1.4.1.6296.101.11.3.2.10 |
sleArpNotification OBJECT IDENTIFIER .1.3.6.1.4.1.6296.101.11.3.3 |
sleArpEntryCreatedcreateArpEntry. NOTIFICATION-TYPE .1.3.6.1.4.1.6296.101.11.3.3.1 |
sleArpEntryDestroyeddestroyArpEntry. NOTIFICATION-TYPE .1.3.6.1.4.1.6296.101.11.3.3.2 |
sleArpTableClearedclearArpTable. In this notification PDU, key of sleArpState is ifindex.0.0.0.0. NOTIFICATION-TYPE .1.3.6.1.4.1.6296.101.11.3.3.3 |
sleArpTableClearedByAddrclearArpTableByAddr NOTIFICATION-TYPE .1.3.6.1.4.1.6296.101.11.3.3.4 |
sleRoute OBJECT IDENTIFIER .1.3.6.1.4.1.6296.101.11.4 |
sleRouteTableDescription. SEQUENCE OF SleRouteEntry .1.3.6.1.4.1.6296.101.11.4.1 |
sleRouteEntryDescription. SleRouteEntry .1.3.6.1.4.1.6296.101.11.4.1.1 |
sleRouteDstAddressThe destination IP address of this route. An entry with a value of 0.0.0.0 is considered a default route. Multiple routes to a single destination can appear in the table, but access to such multiple entries is dependent on the table-access mechanisms defined by the network management protocol in use.ro IpAddress .1.3.6.1.4.1.6296.101.11.4.1.1.1 |
sleRouteDstMaskIndicate the mask to be logical-ANDed with the destination address before being compared to the value in the sleRouteDstAddress field. For those systems that do not support arbitrary subnet masks, an agent constructs the value of the sleRouteDstMask by determining whether the value of the correspondent sleRouteDstAddress field belong to a class-A, B, or C network. If the value of the sleRouteDstAddress is 0.0.0.0 (a default route), then the mask value is also 0.0.0.0. It should be noted that all IP routing subsystems implicitly use this mechanism.ro INTEGER .1.3.6.1.4.1.6296.101.11.4.1.1.2 |
sleRouteGatewayThe Gateway IP Address. 0.0.0.0/0 : indicate default gateway or invalidro IpAddress .1.3.6.1.4.1.6296.101.11.4.1.1.3 |
sleRouteInterfaceThe index value which uniquely identifies the local interface through which the next hop of this route should be reached. The interface identified by a particular value of this index is the same interface as identified by the same value of sleNetIfIndex. Network interface index 0: invalid 1..4094: VLAN 4095: management 4096: loopback 4097: NULL device 10000..11023: Tunnel interface indexro INTEGER .1.3.6.1.4.1.6296.101.11.4.1.1.4 |
sleRouteTypeThe type of route. Note that the values direct and indirect refer to the notion of direct and indirect routing in the IP architecture. Setting this object to the value invalid has the effect of invalidating the corresponding entry in the sleRouteTable object. That is, it effectively dissasociates the destination identified with said entry from the route identified with said entry. It is an implementation-specific matter as to whether the agent removes an invalidated entry from the table. Accordingly, management stations must be prepared to receive tabular information from agents that corresponds to entries not currently in use. Proper interpretation of such entries requires examination of the relevant sleRouteType object.rw Enumeration .1.3.6.1.4.1.6296.101.11.4.1.1.5 |
sleRouteProtoThe routing mechanism via which this route was learned. Inclusion of values for gateway routing protocols is not intended to imply that hosts should support those protocols.ro Enumeration .1.3.6.1.4.1.6296.101.11.4.1.1.6 |
sleRouteMetricThe primary routing metric for this route. The semantics of this metric are determined by the routing-protocol specified in the route's sleRouteProto value. If this metric is not used, its value should be set to -1.rw INTEGER (-1..255) .1.3.6.1.4.1.6296.101.11.4.1.1.7 |
sleRouteActiveThe active status for this routing entry.rw Enumeration .1.3.6.1.4.1.6296.101.11.4.1.1.8 |
sleRouteBindingSrcAddrThe binding source IP Address for this route.ro IpAddress .1.3.6.1.4.1.6296.101.11.4.1.1.9 |
sleRouteDistanceThe Distance value for this route.rw INTEGER .1.3.6.1.4.1.6296.101.11.4.1.1.10 |
sleRouteSubtypeThe subtype of this route.ro Enumeration .1.3.6.1.4.1.6296.101.11.4.1.1.11 |
sleRouteNexthopStatusThe nexthop status of this route.ro Bits .1.3.6.1.4.1.6296.101.11.4.1.1.12 |
sleRouteRibStatusThe rib status for this route.ro Bits .1.3.6.1.4.1.6296.101.11.4.1.1.13 |
sleRouteVRFIndexVRF index in sleIpVRFTable.ro Integer32 .1.3.6.1.4.1.6296.101.11.4.1.1.14 |
sleRouteControl OBJECT IDENTIFIER .1.3.6.1.4.1.6296.101.11.4.2 |
sleRouteControlRequestThe request of a user command.rw Enumeration .1.3.6.1.4.1.6296.101.11.4.2.1 |
sleRouteControlStatusThe status of a user command.ro SleControlStatusType (SLE-TC-MIB) .1.3.6.1.4.1.6296.101.11.4.2.2 |
sleRouteControlTimerThe maximum wait time for the manager for a long running user command.rw Gauge32 .1.3.6.1.4.1.6296.101.11.4.2.3 |
sleRouteControlTimeStampThe result of the last user command.ro SleControlRequestResultType (SLE-TC-MIB) .1.3.6.1.4.1.6296.101.11.4.2.4 |
sleRouteControlReqResultThe time stamp of the last command (end of command).ro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.6296.101.11.4.2.5 |
sleRouteControlDstAddressThe destination IP address of this route. An entry with a value of 0.0.0.0 is considered a default route. Multiple routes to a single destination can appear in the table, but access to such multiple entries is dependent on the table-access mechanisms defined by the network management protocol in use.rw IpAddress .1.3.6.1.4.1.6296.101.11.4.2.6 |
sleRouteControlDstMaskIndicate the mask to be logical-ANDed with the destination address before being compared to the value in the sleRouteDstAddress field. For those systems that do not support arbitrary subnet masks, an agent constructs the value of the sleRouteDstMask by determining whether the value of the correspondent sleRouteDstAddress field belong to a class-A, B, or C network. If the value of the sleRouteDstAddress is 0.0.0.0 (a default route), then the mask value is also 0.0.0.0. It should be noted that all IP routing subsystems implicitly use this mechanism.rw INTEGER .1.3.6.1.4.1.6296.101.11.4.2.7 |
sleRouteControlGatewayThe Gateway IP Address. 0.0.0.0/0 : indicate default gateway or invalidrw IpAddress .1.3.6.1.4.1.6296.101.11.4.2.8 |
sleRouteControlInterfaceNetwork interface index 0: invalid 1..4094: VLAN 4095: management 4096: loopback 4097: NULL device 10000..11023: Tunnel interface index To config interface, sleRouteControlGateway have to be removed.rw INTEGER .1.3.6.1.4.1.6296.101.11.4.2.9 |
sleRouteControlBindingSrcAddrThe binding source IP Address for this route.rw IpAddress .1.3.6.1.4.1.6296.101.11.4.2.10 |
sleRouteControlDistanceThe Distance value for this route.rw INTEGER .1.3.6.1.4.1.6296.101.11.4.2.11 |
sleRouteControlVRFIndexVRF index in sleIpVRFTable.rw Integer32 .1.3.6.1.4.1.6296.101.11.4.2.12 |
sleRouteNotification OBJECT IDENTIFIER .1.3.6.1.4.1.6296.101.11.4.3 |
sleRouteStaticCreatedcreateStaticRoute NOTIFICATION-TYPE .1.3.6.1.4.1.6296.101.11.4.3.1 |
sleRouteStaticDestroyeddestroyStaticRoute NOTIFICATION-TYPE .1.3.6.1.4.1.6296.101.11.4.3.2 |
sleRouteStaticProfileChangedsetStaticRouteProfile NOTIFICATION-TYPE .1.3.6.1.4.1.6296.101.11.4.3.3 |
sleDhcpClient OBJECT IDENTIFIER .1.3.6.1.4.1.6296.101.11.5 |
sleDhcpClTableDescription. SEQUENCE OF SleDhcpClEntry .1.3.6.1.4.1.6296.101.11.5.1 |
sleDhcpClEntryDescription. SleDhcpClEntry .1.3.6.1.4.1.6296.101.11.5.1.1 |
sleDhcpClModeDHCP Client activity state in this interface.ro Enumeration .1.3.6.1.4.1.6296.101.11.5.1.1.1 |
sleDhcpClIpAddrThe IP address acquired by DHCP Client active in this interface.ro IpAddress .1.3.6.1.4.1.6296.101.11.5.1.1.2 |
sleDhcpClNetmaskThe subnet mask associated with the IP address acquired by DHCP Client. The value of the mask is an IP address with all the network bits set to 1 and all the hosts bits set to 0.ro IpAddress .1.3.6.1.4.1.6296.101.11.5.1.1.3 |
sleDhcpClGatewayThe Gateway's IP address acquired by DHCP Client active in this interface.ro IpAddress .1.3.6.1.4.1.6296.101.11.5.1.1.4 |
sleDhcpClDnsServerThe DNS server's IP address acquired by DHCP Client active in this interface.ro IpAddress .1.3.6.1.4.1.6296.101.11.5.1.1.5 |
sleDhcpClServerDHCP Server's IP address.ro IpAddress .1.3.6.1.4.1.6296.101.11.5.1.1.6 |
sleDhcpClClientIdDHCP Client-identifier value. This is used by DHCP clients to specify their unique identifier. DHCP servers use this value to index their database of address bindings. This value is expected to be unique for all clients in an administrative domain.ro OCTET STRING .1.3.6.1.4.1.6296.101.11.5.1.1.7 |
sleDhcpClClientIdStyleDHCP Client-identifier input style. 0 : ascii string format 1 : hexadecimal formatro Enumeration .1.3.6.1.4.1.6296.101.11.5.1.1.8 |
sleDhcpClClassIdDHCP Class identifier value. This is used by DHCP clients to optionally identify the vendor type and configuration of a DHCP client. The information is a string of n octets, interpreted by servers. Vendors may choose to define specific vendor class identifiers to convey particular configuration or other identification information about a client. For example, the identifier may encode the client's hardware configuration.ro OCTET STRING .1.3.6.1.4.1.6296.101.11.5.1.1.9 |
sleDhcpClClassIdStyleDHCP Class identifier input style. 0 : ascii string format 1 : hexadecimal formatro Enumeration .1.3.6.1.4.1.6296.101.11.5.1.1.10 |
sleDhcpClLeasetimeThe leased time for IP address acquired by DHCP Client. Default lease-time: 3600sro Integer32 .1.3.6.1.4.1.6296.101.11.5.1.1.11 |
sleDhcpClStateThe operating status of DHCP Client.ro Enumeration .1.3.6.1.4.1.6296.101.11.5.1.1.12 |
sleDhcpClControl OBJECT IDENTIFIER .1.3.6.1.4.1.6296.101.11.5.2 |
sleDhcpClControlRequestThe request of a user command.rw Enumeration .1.3.6.1.4.1.6296.101.11.5.2.1 |
sleDhcpClControlStatusThe status of a user command.ro SleControlStatusType (SLE-TC-MIB) .1.3.6.1.4.1.6296.101.11.5.2.2 |
sleDhcpClControlTimerThe maximum wait time for the manager for a long running user command.rw Gauge32 .1.3.6.1.4.1.6296.101.11.5.2.3 |
sleDhcpClControlTimeStampThe time stamp of the last command (end of command).ro SleControlRequestResultType (SLE-TC-MIB) .1.3.6.1.4.1.6296.101.11.5.2.4 |
sleDhcpClControlReqResultThe result of the last user command.ro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.6296.101.11.5.2.5 |
sleDhcpClControlNetIfIndexNetwork Interface Index.rw Integer32 .1.3.6.1.4.1.6296.101.11.5.2.6 |
sleDhcpClControlModeDHCP Client activity state in this interface.rw Enumeration .1.3.6.1.4.1.6296.101.11.5.2.7 |
sleDhcpClControlClientIdDHCP Client-identifier value. This is used by DHCP clients to specify their unique identifier. DHCP servers use this value to index their database of address bindings. This value is expected to be unique for all clients in an administrative domain.rw OCTET STRING .1.3.6.1.4.1.6296.101.11.5.2.8 |
sleDhcpClControlClientIdStyleDHCP Client-identifier input style. 0 : ascii string format 1 : hexadecimal formatrw Enumeration .1.3.6.1.4.1.6296.101.11.5.2.9 |
sleDhcpClControlClassIdDHCP Class identifier value. This is used by DHCP clients to optionally identify the vendor type and configuration of a DHCP client. The information is a string of n octets, interpreted by servers. Vendors may choose to define specific vendor class identifiers to convey particular configuration or other identification information about a client. For example, the identifier may encode the client's hardware configuration.rw OCTET STRING .1.3.6.1.4.1.6296.101.11.5.2.10 |
sleDhcpClControlClassIdStyleDHCP Class identifier input style. 0 : ascii string format 1 : hexadecimal formatrw Enumeration .1.3.6.1.4.1.6296.101.11.5.2.11 |
sleDhcpClControlLeasetimeThe leased time for IP address acquired by DHCP Client. Default lease-time: 3600srw Integer32 .1.3.6.1.4.1.6296.101.11.5.2.12 |
sleDhcpClControlUpdateIPUpdate DHCP client operating status. 0 : default 1 : renew 2 : releaserw Enumeration .1.3.6.1.4.1.6296.101.11.5.2.13 |
sleDhcpClNotification OBJECT IDENTIFIER .1.3.6.1.4.1.6296.101.11.5.3 |
sleDhcpClModeChangedsetDhcpClMode. NOTIFICATION-TYPE .1.3.6.1.4.1.6296.101.11.5.3.1 |
sleDhcpClProfileChangedsetDhcpClProfile. NOTIFICATION-TYPE .1.3.6.1.4.1.6296.101.11.5.3.2 |
sleDhcpClStateChangedChangeDhcpClState. NOTIFICATION-TYPE .1.3.6.1.4.1.6296.101.11.5.3.3 |
sleV2DhcpClient OBJECT IDENTIFIER .1.3.6.1.4.1.6296.101.11.6 |
sleNetworkBase OBJECT IDENTIFIER .1.3.6.1.4.1.6296.101.11.7 |
sleNetworkBaseInfo OBJECT IDENTIFIER .1.3.6.1.4.1.6296.101.11.7.1 |
sleNetworkArpAgingTimeSystem Arp Aging Timero INTEGER .1.3.6.1.4.1.6296.101.11.7.1.1 |
sleNetworkBaseVrfDynamicForwardBindingDescription.ro Enumeration .1.3.6.1.4.1.6296.101.11.7.1.2 |
sleNetworkBaseControl OBJECT IDENTIFIER .1.3.6.1.4.1.6296.101.11.7.2 |
sleNetworkControlRequestDescription.rw Enumeration .1.3.6.1.4.1.6296.101.11.7.2.1 |
sleNetworkControlStatusDescription.ro SleControlStatusType (SLE-TC-MIB) .1.3.6.1.4.1.6296.101.11.7.2.2 |
sleNetworkControlTimerDescription.rw Gauge32 .1.3.6.1.4.1.6296.101.11.7.2.3 |
sleNetworkControlTimeStampDescription.ro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.6296.101.11.7.2.4 |
sleNetworkControlReqResultDescription.ro SleControlRequestResultType (SLE-TC-MIB) .1.3.6.1.4.1.6296.101.11.7.2.5 |
sleNetworkControlArpAgingTimeDescription.rw INTEGER .1.3.6.1.4.1.6296.101.11.7.2.6 |
sleNetworkControlVrfDynamicForwardBindingDescription.rw Enumeration .1.3.6.1.4.1.6296.101.11.7.2.7 |
sleNetworkBaseNotification OBJECT IDENTIFIER .1.3.6.1.4.1.6296.101.11.7.3 |
sleNetworkArpProfileChangedDescription. NOTIFICATION-TYPE .1.3.6.1.4.1.6296.101.11.7.3.1 |
sleTunnel OBJECT IDENTIFIER .1.3.6.1.4.1.6296.101.11.8 |
sleTunnelIfTableDescription. SEQUENCE OF SleTunnelIfEntry .1.3.6.1.4.1.6296.101.11.8.1 |
sleTunnelIfEntryDescription. SleTunnelIfEntry .1.3.6.1.4.1.6296.101.11.8.1.1 |
sleTunnelIfIndexTunnel interface indexro Integer32 .1.3.6.1.4.1.6296.101.11.8.1.1.1 |
sleTunnelIfLocalAddressThe address of the local endpoint of the tunnel (i.e., the source address used in the outer IP header), or 0.0.0.0 if unknown.ro IpAddress .1.3.6.1.4.1.6296.101.11.8.1.1.2 |
sleTunnelIfRemoteAddressThe address of the remote endpoint of the tunnel (i.e., the destination address used in the outer IP header), or 0.0.0.0 if unknown.ro IpAddress .1.3.6.1.4.1.6296.101.11.8.1.1.3 |
sleTunnelIfModeThe encapsulation method used by the tunnel. other(1) - none of the following direct(2) - intermediate header gre(3) - GRE encapsulation minimal(4) - Minimal encapsulation l2tp(5) - L2TP encapsulation pptp(6) - PPTP encapsulation l2f(7) - L2F encapsulation udp(8) - UDP encapsulation atmp(9) - ATMP encapsulation msdp(10) - MSDP encapsulation sixToFour(11) - 6to4 encapsulation sixOverFour(12) - 6over4 encapsulation isatap(13) - ISATAP encapsulation teredo(14) - Teredo encapsulationro IANAtunnelType (IANAifType-MIB) .1.3.6.1.4.1.6296.101.11.8.1.1.4 |
sleTunnelIfTTLThe TTL to use in the outer IP header.ro Integer32 .1.3.6.1.4.1.6296.101.11.8.1.1.5 |
sleTunnelIfDscpModeThe DiffServ field mode to use in the outer IP header. A value of dscpCopyFromPacket indicates that the bits are copied from the payload's header. A value of dscpMapFromPacket indicates that the bit field is mapping dscp field of incoming packet. A value of dscpAssign indicates that the bit field is static DiffServ field value.ro Enumeration .1.3.6.1.4.1.6296.101.11.8.1.1.6 |
sleTunnelIfDscpThe static DiffServ field value to use in the outer IP header.ro Integer32 .1.3.6.1.4.1.6296.101.11.8.1.1.7 |
sleTunnelIfKeepaliveIntervalSpecifies the time interval, in seconds, at which keepalive packets are sent. (This object is available for a gre tunnel only.)ro Integer32 .1.3.6.1.4.1.6296.101.11.8.1.1.8 |
sleTunnelIfKeepaliveRetrySpecifies the number times that the device will continue to send keepalive packets without response before bringing the tunnel interface protocol down. (This object is available for a gre tunnel only.)ro Integer32 .1.3.6.1.4.1.6296.101.11.8.1.1.9 |
sleTunnelIfPathMtuDiscoveryPath mtu discovery on tunnel.ro Enumeration .1.3.6.1.4.1.6296.101.11.8.1.1.10 |
sleTunnelIfVRFNameVPN Routing/Forwarding instance name.ro OCTET STRING .1.3.6.1.4.1.6296.101.11.8.1.1.11 |
sleTunnelIfBindingPortsTunnel binding ports map.ro OCTET STRING .1.3.6.1.4.1.6296.101.11.8.1.1.12 |
sleTunnelIfLocalAddress6The address of the local endpoint of the tunnel for IPv6ro InetAddress (INET-ADDRESS-MIB) .1.3.6.1.4.1.6296.101.11.8.1.1.13 |
sleTunnelIfRemoteAddress6The address of the remote endpoint of the tunnel for IPv6ro InetAddress (INET-ADDRESS-MIB) .1.3.6.1.4.1.6296.101.11.8.1.1.14 |
sleTunnelIfChecksumA checksum feature for the tunnel.ro Enumeration .1.3.6.1.4.1.6296.101.11.8.1.1.15 |
sleTunnelIfDmacA destination MAC address for tunneled packets. (IP-in-IP tunneling on Broadcom.)ro MacAddress (SNMPv2-TC) .1.3.6.1.4.1.6296.101.11.8.1.1.16 |
sleTunnelIfTosA value of Type of Service (TOS) in the tunnel IPv4 encapsulation header.ro INTEGER .1.3.6.1.4.1.6296.101.11.8.1.1.17 |
sleTunnelIfControl OBJECT IDENTIFIER .1.3.6.1.4.1.6296.101.11.8.2 |
sleTunnelIfControlRequestThe request of a user command.rw Enumeration .1.3.6.1.4.1.6296.101.11.8.2.1 |
sleTunnelIfControlStatusThe status of a user command.ro SleControlStatusType (SLE-TC-MIB) .1.3.6.1.4.1.6296.101.11.8.2.2 |
sleTunnelIfControlTimerThe maximum wait time for the manager for a long running user command.rw Gauge32 .1.3.6.1.4.1.6296.101.11.8.2.3 |
sleTunnelIfControlTimeStampThe result of the last user command.ro SleControlRequestResultType (SLE-TC-MIB) .1.3.6.1.4.1.6296.101.11.8.2.4 |
sleTunnelIfControlReqResultThe time stamp of the last command (end of command).ro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.6296.101.11.8.2.5 |
sleTunnelIfControlIndexTunnel interface indexrw Integer32 .1.3.6.1.4.1.6296.101.11.8.2.6 |
sleTunnelIfControlLocalAddressThe address of the local endpoint of the tunnel (i.e., the source address used in the outer IP header), or 0.0.0.0 if unknown.rw IpAddress .1.3.6.1.4.1.6296.101.11.8.2.7 |
sleTunnelIfControlRemoteAddressThe address of the remote endpoint of the tunnel (i.e., the destination address used in the outer IP header), or 0.0.0.0 if unknown.rw IpAddress .1.3.6.1.4.1.6296.101.11.8.2.8 |
sleTunnelIfControlModeThe encapsulation method used by the tunnel. other(1) - none of the following direct(2) - intermediate header gre(3) - GRE encapsulation minimal(4) - Minimal encapsulation l2tp(5) - L2TP encapsulation pptp(6) - PPTP encapsulation l2f(7) - L2F encapsulation udp(8) - UDP encapsulation atmp(9) - ATMP encapsulation msdp(10) - MSDP encapsulation sixToFour(11) - 6to4 encapsulation sixOverFour(12) - 6over4 encapsulation isatap(13) - ISATAP encapsulation teredo(14) - Teredo encapsulationrw IANAtunnelType (IANAifType-MIB) .1.3.6.1.4.1.6296.101.11.8.2.9 |
sleTunnelIfControlTTLThe TTL to use in the outer IP header.rw Integer32 .1.3.6.1.4.1.6296.101.11.8.2.10 |
sleTunneIflControlDscpModeThe DiffServ field mode to use in the outer IP header. A value of dscpCopyFromPacket indicates that the bits are copied from the payload's header. A value of dscpMapFromPacket indicates that the bit field is mapping dscp field of incoming packet. A value of dscpAssign indicates that the bit field is static DiffServ field value.rw Enumeration .1.3.6.1.4.1.6296.101.11.8.2.11 |
sleTunneIflControlDscpThe static DiffServ field value to use in the outer IP header.rw Integer32 .1.3.6.1.4.1.6296.101.11.8.2.12 |
sleTunnelIfControlKeepaliveIntervalSpecifies the time interval, in seconds, at which keepalive packets are sent. (This object is available for a gre tunnel only.)rw Integer32 .1.3.6.1.4.1.6296.101.11.8.2.13 |
sleTunneIflControlKeepaliveRetrySpecifies the number times that the device will continue to send keepalive packets without response before bringing the tunnel interface protocol down. (This object is available for a gre tunnel only.)rw Integer32 .1.3.6.1.4.1.6296.101.11.8.2.14 |
sleTunnelIfControlPathMtuDiscoveryPath mtu discovery on tunnel.rw Enumeration .1.3.6.1.4.1.6296.101.11.8.2.15 |
sleTunnelIfControlVRFNameVPN Routing/Forwarding instance name.rw OCTET STRING .1.3.6.1.4.1.6296.101.11.8.2.16 |
sleTunnelIfControlLocalAddress6The address of the local endpoint of the tunnel for IPv6rw InetAddress (INET-ADDRESS-MIB) .1.3.6.1.4.1.6296.101.11.8.2.17 |
sleTunnelIfControlRemoteAddress6The address of the remote endpoint of the tunnel for IPv6rw InetAddress (INET-ADDRESS-MIB) .1.3.6.1.4.1.6296.101.11.8.2.18 |
sleTunnelIfControlChecksumA checksum feature for the tunnel.rw Enumeration .1.3.6.1.4.1.6296.101.11.8.2.19 |
sleTunnelIfControlDmacA destination MAC address for tunneled packets. (IP-in-IP tunneling on Broadcom.)rw MacAddress (SNMPv2-TC) .1.3.6.1.4.1.6296.101.11.8.2.20 |
sleTunnelIfControlTosA value of Type of Service (TOS) in the tunnel IPv4 encapsulation header.rw INTEGER .1.3.6.1.4.1.6296.101.11.8.2.21 |
sleTunnelIfNotification OBJECT IDENTIFIER .1.3.6.1.4.1.6296.101.11.8.3 |
sleTunnelIfCreatedDescription. NOTIFICATION-TYPE .1.3.6.1.4.1.6296.101.11.8.3.1 |
sleTunnelIfDeletedDescription. NOTIFICATION-TYPE .1.3.6.1.4.1.6296.101.11.8.3.2 |
sleTunnelIfLocalAddressChangedDescription. NOTIFICATION-TYPE .1.3.6.1.4.1.6296.101.11.8.3.3 |
sleTunnelIfRemoteAddressChangedDescription. NOTIFICATION-TYPE .1.3.6.1.4.1.6296.101.11.8.3.4 |
sleTunnelIfModeChangedDescription. NOTIFICATION-TYPE .1.3.6.1.4.1.6296.101.11.8.3.5 |
sleTunnelIfTTLChangedDescription. NOTIFICATION-TYPE .1.3.6.1.4.1.6296.101.11.8.3.6 |
sleTunnelIfDscpChangedDescription. NOTIFICATION-TYPE .1.3.6.1.4.1.6296.101.11.8.3.7 |
sleTunnelIfKeepaliveChangedDescription. NOTIFICATION-TYPE .1.3.6.1.4.1.6296.101.11.8.3.8 |
sleTunnelIfPathMtuDiscoveryChangedDescription. NOTIFICATION-TYPE .1.3.6.1.4.1.6296.101.11.8.3.9 |
sleTunnelIfVRFNameSetDescription. NOTIFICATION-TYPE .1.3.6.1.4.1.6296.101.11.8.3.10 |
sleTunnelIfVRFNameUnsetDescription. NOTIFICATION-TYPE .1.3.6.1.4.1.6296.101.11.8.3.11 |
sleTunnelIfLocalAddress6ChangedsetTunnelLocalAddr6 NOTIFICATION-TYPE .1.3.6.1.4.1.6296.101.11.8.3.12 |
sleTunnelIfRemoteAddress6ChangedsetTunnelRemoteAddr6 NOTIFICATION-TYPE .1.3.6.1.4.1.6296.101.11.8.3.13 |
sleTunnelAddressTableDescription. SEQUENCE OF SleTunnelAddressEntry .1.3.6.1.4.1.6296.101.11.8.4 |
sleTunnelAddressEntryDescription. SleTunnelAddressEntry .1.3.6.1.4.1.6296.101.11.8.4.1 |
sleTunnelAddressValueThe IP address to which this entry's addressing information pertains.ro IpAddress .1.3.6.1.4.1.6296.101.11.8.4.1.1 |
sleTunnelAddressMaskThe subnet mask associated with the IP address of this entry. The value of the mask is an IP address with all the network bits set to 1 and all the hosts bits set to 0.ro Integer32 .1.3.6.1.4.1.6296.101.11.8.4.1.2 |
sleTunnelIpAddrBcastDescription.ro IpAddress .1.3.6.1.4.1.6296.101.11.8.4.1.3 |
sleTunnelAddressFlagdynamic: ~ permanent primary : ~ secondary anycast: this bit is available for ipv6 only. The others are available for ipv4 only.ro Bits .1.3.6.1.4.1.6296.101.11.8.4.1.4 |
sleTunnelAddressScopedefault : global In linux, 200 - site 0 - global 1..252 - scopeNUM 253 - link 254 - host 255 - nowherero Integer32 .1.3.6.1.4.1.6296.101.11.8.4.1.5 |
sleTunnelAddressUnnumIfIndexThe unnumbered-source interface index (Before ip unnumbered feature is set, a tunnel interface must be created.) (ex. br100 -> 100, br200 -> 200)ro INTEGER .1.3.6.1.4.1.6296.101.11.8.4.1.6 |
sleTunnelAddressUnnumIpIndexThe Ip index for Interface Unnumbered feature enhanced. If Interface Unnumbered enhanced feature is enabled on a point-to-point interface. It will get a ip address of a specific interface. Interface unnumbered default setting - it get primary ip address. Interface unnumbered enhanced setting - it get secondary ip address with ip-index. (cf. primary ip address's ip-index : 1. no setting: 0. other setting: 2-1024)ro INTEGER (0 | 2..1024) .1.3.6.1.4.1.6296.101.11.8.4.1.7 |
sleTunnelAddressControl OBJECT IDENTIFIER .1.3.6.1.4.1.6296.101.11.8.5 |
sleTunnelAddressControlRequestThe request of a user command.rw Enumeration .1.3.6.1.4.1.6296.101.11.8.5.1 |
sleTunnelAddressControlStatusThe status of a user command.ro SleControlStatusType (SLE-TC-MIB) .1.3.6.1.4.1.6296.101.11.8.5.2 |
sleTunnelAddressControlTimerThe maximum wait time for the manager for a long running user command.rw Gauge32 .1.3.6.1.4.1.6296.101.11.8.5.3 |
sleTunnelAddressControlTimeStampThe result of the last user command.ro SleControlRequestResultType (SLE-TC-MIB) .1.3.6.1.4.1.6296.101.11.8.5.4 |
sleTunnelAddressControlReqResultThe time stamp of the last command (end of command).ro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.6296.101.11.8.5.5 |
sleTunnelAddressControlTunnelIfIndexTunnel interface indexrw Integer32 .1.3.6.1.4.1.6296.101.11.8.5.6 |
sleTunnelAddressControlValueThe IP address to which this entry's addressing information pertains.rw IpAddress .1.3.6.1.4.1.6296.101.11.8.5.7 |
sleTunnelAddressControlMaskThe subnet mask associated with the IP address of this entry. The value of the mask is an IP address with all the network bits set to 1 and all the hosts bits set to 0.rw Integer32 .1.3.6.1.4.1.6296.101.11.8.5.8 |
sleTunnelAddressControlFlagdefault : primaryrw Enumeration .1.3.6.1.4.1.6296.101.11.8.5.9 |
sleTunnelAddressControlScopedefault : global not applicable : nowhererw Enumeration .1.3.6.1.4.1.6296.101.11.8.5.10 |
sleTunnelAddressControlUnnumIfIndexThe unnumbered-source interface index (Before ip unnumbered feature is set, a tunnel interface must be created.) (ex. br100 -> 100, br200 -> 200)rw INTEGER .1.3.6.1.4.1.6296.101.11.8.5.11 |
sleTunnelAddressControlUnnumIpIndexThe Ip index for Interface Unnumbered feature enhanced. If Interface Unnumbered enhanced feature is enabled on a point-to-point interface. It will get a ip address of a specific interface. Interface unnumbered default setting - it get primary ip address. Interface unnumbered enhanced setting - it get secondary ip address with ip-index. (cf. primary ip address's ip-index : 1. no setting: 0. other setting: 2-1024)rw INTEGER (0 | 2..1024) .1.3.6.1.4.1.6296.101.11.8.5.12 |
sleTunnelAddressNotification OBJECT IDENTIFIER .1.3.6.1.4.1.6296.101.11.8.6 |
sleTunnelAddressCreatedDescription. NOTIFICATION-TYPE .1.3.6.1.4.1.6296.101.11.8.6.1 |
sleTunnelAddressDeletedDescription. NOTIFICATION-TYPE .1.3.6.1.4.1.6296.101.11.8.6.2 |
sleTunnelAddressUnnumChangedsetIfUnnumbered NOTIFICATION-TYPE .1.3.6.1.4.1.6296.101.11.8.6.3 |
sleTunnelAddressUnnumDeleteddelIfUnnumbered NOTIFICATION-TYPE .1.3.6.1.4.1.6296.101.11.8.6.4 |
sleIpVRF OBJECT IDENTIFIER .1.3.6.1.4.1.6296.101.11.9 |
sleIpVRFTableDescription. SEQUENCE OF SleIpVRFEntry .1.3.6.1.4.1.6296.101.11.9.1 |
sleIpVRFEntryDescription. SleIpVRFEntry .1.3.6.1.4.1.6296.101.11.9.1.1 |
sleIpVRFIndexVRF index.ro Integer32 .1.3.6.1.4.1.6296.101.11.9.1.1.1 |
sleIpVRFNameVRF name.ro OCTET STRING .1.3.6.1.4.1.6296.101.11.9.1.1.2 |
sleIpVRFDesignatedPortsThe port map of VRF designated-port.ro OCTET STRING .1.3.6.1.4.1.6296.101.11.9.1.1.3 |
sleIpVRFRouterIdRouter-Identifierro IpAddress .1.3.6.1.4.1.6296.101.11.9.1.1.4 |
sleIpVRFDescriptionThe description of VRF.ro OCTET STRING .1.3.6.1.4.1.6296.101.11.9.1.1.5 |
sleIpVRFControl OBJECT IDENTIFIER .1.3.6.1.4.1.6296.101.11.9.2 |
sleIpVRFControlRequestThe request of a user command.rw Enumeration .1.3.6.1.4.1.6296.101.11.9.2.1 |
sleIpVRFControlStatusThe status of a user command.ro SleControlStatusType (SLE-TC-MIB) .1.3.6.1.4.1.6296.101.11.9.2.2 |
sleIpVRFControlTimerThe maximum wait time for the manager for a long running user command.rw Gauge32 .1.3.6.1.4.1.6296.101.11.9.2.3 |
sleIpVRFControlTimeStampThe result of the last user command.ro SleControlRequestResultType (SLE-TC-MIB) .1.3.6.1.4.1.6296.101.11.9.2.4 |
sleIpVRFControlReqResultThe time stamp of the last command (end of command).ro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.6296.101.11.9.2.5 |
sleIpVRFControlNameVRF namerw OCTET STRING .1.3.6.1.4.1.6296.101.11.9.2.6 |
sleIpVRFControlDesignatedPortsThe port map of VRF designated-port.rw OCTET STRING .1.3.6.1.4.1.6296.101.11.9.2.7 |
sleIpVRFControlRouterIdRouter-Identifierrw IpAddress .1.3.6.1.4.1.6296.101.11.9.2.8 |
sleIpVRFControlDescriptionThe description of VRF.rw OCTET STRING .1.3.6.1.4.1.6296.101.11.9.2.9 |
sleIpVRFNotification OBJECT IDENTIFIER .1.3.6.1.4.1.6296.101.11.9.3 |
sleIpVRFCreatedDescription. NOTIFICATION-TYPE .1.3.6.1.4.1.6296.101.11.9.3.1 |
sleIpVRFDeletedDescription. NOTIFICATION-TYPE .1.3.6.1.4.1.6296.101.11.9.3.2 |
sleIpVRFDesignatedPortsSetDescription. NOTIFICATION-TYPE .1.3.6.1.4.1.6296.101.11.9.3.3 |
sleIpVRFDesignatedPortsUnsetDescription. NOTIFICATION-TYPE .1.3.6.1.4.1.6296.101.11.9.3.4 |
sleIpVRFRouterIdChangedDescription. NOTIFICATION-TYPE .1.3.6.1.4.1.6296.101.11.9.3.5 |
sleIpVRFDescriptionChangedDescription. NOTIFICATION-TYPE .1.3.6.1.4.1.6296.101.11.9.3.6 |
sleIpVRFSelectionSourceTableDescription. SEQUENCE OF SleIpVRFSelectionSourceEntry .1.3.6.1.4.1.6296.101.11.9.4 |
sleIpVRFSelectionSourceEntryDescription. SleIpVRFSelectionSourceEntry .1.3.6.1.4.1.6296.101.11.9.4.1 |
sleIpVRFSelectionSrcIndexVRF selection source index.ro INTEGER .1.3.6.1.4.1.6296.101.11.9.4.1.1 |
sleIpVRFSelectionSrcAddrVRF selection by source IP address.ro IpAddress .1.3.6.1.4.1.6296.101.11.9.4.1.2 |
sleIpVRFSelectionSrcMaskThe subnet mask associated with the IP address of this entry. The value of the mask is an IP address with all the network bits set to 1 and all the hosts bits set to 0.ro Integer32 .1.3.6.1.4.1.6296.101.11.9.4.1.3 |
sleIpVRFSelectionSrcVRFNameVPN Routing/Forwarding instance name.ro OCTET STRING .1.3.6.1.4.1.6296.101.11.9.4.1.4 |
sleIpVRFSelectionSourceControl OBJECT IDENTIFIER .1.3.6.1.4.1.6296.101.11.9.5 |
sleIpVRFSelectionSrcControlRequestThe request of a user command.rw Enumeration .1.3.6.1.4.1.6296.101.11.9.5.1 |
sleIpVRFSelectionSrcControlStatusThe status of a user command.ro SleControlStatusType (SLE-TC-MIB) .1.3.6.1.4.1.6296.101.11.9.5.2 |
sleIpVRFSelectionSrcControlTimerThe maximum wait time for the manager for a long running user command.rw Gauge32 .1.3.6.1.4.1.6296.101.11.9.5.3 |
sleIpVRFSelectionSrcControlTimeStampThe result of the last user command.ro SleControlRequestResultType (SLE-TC-MIB) .1.3.6.1.4.1.6296.101.11.9.5.4 |
sleIpVRFSelectionSrcControlReqResultThe time stamp of the last command (end of command).ro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.6296.101.11.9.5.5 |
sleIpVRFSelectionSrcControlAddrVRF selection by source IP address.rw IpAddress .1.3.6.1.4.1.6296.101.11.9.5.6 |
sleIpVRFSelectionSrcControlMaskThe subnet mask associated with the IP address of this entry. The value of the mask is an IP address with all the network bits set to 1 and all the hosts bits set to 0.rw Integer32 .1.3.6.1.4.1.6296.101.11.9.5.7 |
sleIpVRFSelectionSrcControlVRFNameVPN Routing/Forwarding instance name.rw OCTET STRING .1.3.6.1.4.1.6296.101.11.9.5.8 |
sleIpVRFSelectionSourceNotification OBJECT IDENTIFIER .1.3.6.1.4.1.6296.101.11.9.6 |
sleIpVRFSelectionSrcSetDescription. NOTIFICATION-TYPE .1.3.6.1.4.1.6296.101.11.9.6.1 |
sleIpVRFSelectionSrcUnsetDescription. NOTIFICATION-TYPE .1.3.6.1.4.1.6296.101.11.9.6.2 |
sleBFD OBJECT IDENTIFIER .1.3.6.1.4.1.6296.101.11.10 |
sleBFDBase OBJECT IDENTIFIER .1.3.6.1.4.1.6296.101.11.10.1 |
sleBFDBaseInfo OBJECT IDENTIFIER .1.3.6.1.4.1.6296.101.11.10.1.1 |
sleBFDEnableBFD fast-detect is enabled or disabled.ro Enumeration .1.3.6.1.4.1.6296.101.11.10.1.1.1 |
sleBFDEchoEnableBFD Echo function is enabled or disabled.ro Enumeration .1.3.6.1.4.1.6296.101.11.10.1.1.2 |
sleBFDSlowTimerBFD Slow Timer in unit of milliseconds default: 1000(ms)ro INTEGER .1.3.6.1.4.1.6296.101.11.10.1.1.3 |
sleBFDBaseControl OBJECT IDENTIFIER .1.3.6.1.4.1.6296.101.11.10.1.2 |
sleBFDControlRequestThe request of a user commandrw Enumeration .1.3.6.1.4.1.6296.101.11.10.1.2.1 |
sleBFDControlStatusThe status of user command.ro SleControlStatusType (SLE-TC-MIB) .1.3.6.1.4.1.6296.101.11.10.1.2.2 |
sleBFDControlTimerThe maximum time for the manager for a long running user command.rw Gauge32 .1.3.6.1.4.1.6296.101.11.10.1.2.3 |
sleBFDControlTimeStampThe time stamp of the last command(end of command).ro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.6296.101.11.10.1.2.4 |
sleBFDControlReqResultThe result of the last user command.ro SleControlRequestResultType (SLE-TC-MIB) .1.3.6.1.4.1.6296.101.11.10.1.2.5 |
sleBFDControlEnableBFD fast-detect is enabled or disabled.rw Enumeration .1.3.6.1.4.1.6296.101.11.10.1.2.6 |
sleBFDControlEchoEnableBFD Echo function is enabled or disabled.rw Enumeration .1.3.6.1.4.1.6296.101.11.10.1.2.7 |
sleBFDControlSlowTimerBFD Slow Timer in unit of milliseconds default: 1000(ms)rw INTEGER .1.3.6.1.4.1.6296.101.11.10.1.2.8 |
sleBFDBaseNotification OBJECT IDENTIFIER .1.3.6.1.4.1.6296.101.11.10.1.3 |
sleBFDBaseProfileChangedDescription. NOTIFICATION-TYPE .1.3.6.1.4.1.6296.101.11.10.1.3.1 |
sleBFDInterface OBJECT IDENTIFIER .1.3.6.1.4.1.6296.101.11.10.2 |
sleBFDInterfaceTableDescription. SEQUENCE OF SleBFDInterfaceEntry .1.3.6.1.4.1.6296.101.11.10.2.1 |
sleBFDInterfaceEntryDescription. SleBFDInterfaceEntry .1.3.6.1.4.1.6296.101.11.10.2.1.1 |
sleBFDIfRxIntervalRequired Min Rx Interval of BFD control packet in this interface. default: 50(ms)ro INTEGER .1.3.6.1.4.1.6296.101.11.10.2.1.1.1 |
sleBFDIfTxIntervalRequired Min Tx Interval of BFD control packet in this interface. default: 50(ms)ro INTEGER .1.3.6.1.4.1.6296.101.11.10.2.1.1.2 |
sleBFDIfDetectMultiDetect Multi value of BFD control packet in this interface. default: 3ro INTEGER .1.3.6.1.4.1.6296.101.11.10.2.1.1.3 |
sleBFDIfRxIntervalIPv6Required Min Rx Interval of IPv6 BFD control packet in this interface. default: 50(ms)ro Integer32 .1.3.6.1.4.1.6296.101.11.10.2.1.1.4 |
sleBFDIfTxIntervalIJPv6Required Min Tx Interval of IPv6 BFD control packet in this interface. default: 50(ms)ro Integer32 .1.3.6.1.4.1.6296.101.11.10.2.1.1.5 |
sleBFDIfDetectMultiIPv6Detect Multi value of IPv6 BFD control packet in this interface. default: 3ro Integer32 .1.3.6.1.4.1.6296.101.11.10.2.1.1.6 |
sleBFDInterfaceControl OBJECT IDENTIFIER .1.3.6.1.4.1.6296.101.11.10.2.2 |
sleBFDIfControlRequestThe request of a user commandrw Enumeration .1.3.6.1.4.1.6296.101.11.10.2.2.1 |
sleBFDIfControlStatusThe status of user command.ro SleControlStatusType (SLE-TC-MIB) .1.3.6.1.4.1.6296.101.11.10.2.2.2 |
sleBFDIfControlTimerThe maximum time for the manager for a long running user command.rw Gauge32 .1.3.6.1.4.1.6296.101.11.10.2.2.3 |
sleBFDIfControlTimeStampThe time stamp of the last command(end of command).ro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.6296.101.11.10.2.2.4 |
sleBFDIfControlReqResultThe result of the last user command.ro SleControlRequestResultType (SLE-TC-MIB) .1.3.6.1.4.1.6296.101.11.10.2.2.5 |
sleBFDIfControlNetIfIndexBFD Interface Index.rw Integer32 .1.3.6.1.4.1.6296.101.11.10.2.2.6 |
sleBFDIfControlRxIntervalRequired Min Rx Interval of BFD control packet in this interface. default: 50(ms)rw INTEGER .1.3.6.1.4.1.6296.101.11.10.2.2.7 |
sleBFDIfControlTxIntervalRequired Min Tx Interval of BFD control packet in this interface. default: 50(ms)rw INTEGER .1.3.6.1.4.1.6296.101.11.10.2.2.8 |
sleBFDIfControlDetectMultiDetect Multi value of BFD control packet in this interface. default: 3rw INTEGER .1.3.6.1.4.1.6296.101.11.10.2.2.9 |
sleBFDIfControlRxIntervalIPv6Required Min Rx Interval of IPv6 BFD control packet in this interface. default: 50(ms)rw Integer32 .1.3.6.1.4.1.6296.101.11.10.2.2.10 |
sleBFDIfControlTxIntervalIPv6Required Min Tx Interval of IPv6 BFD control packet in this interface. default: 50(ms)rw Integer32 .1.3.6.1.4.1.6296.101.11.10.2.2.11 |
sleBFDIfControlDetectMultiIPv6Detect Multi value of IPv6 BFD control packet in this interface. default: 3rw Integer32 .1.3.6.1.4.1.6296.101.11.10.2.2.12 |
sleBFDInterfaceNotification OBJECT IDENTIFIER .1.3.6.1.4.1.6296.101.11.10.2.3 |
sleBFDIfProfileChangedDescription. NOTIFICATION-TYPE .1.3.6.1.4.1.6296.101.11.10.2.3.1 |
sleBFDSession OBJECT IDENTIFIER .1.3.6.1.4.1.6296.101.11.10.3 |
sleBFDSessionInfo OBJECT IDENTIFIER .1.3.6.1.4.1.6296.101.11.10.3.1 |
sleBFDSessionInfoTableDescription. SEQUENCE OF SleBFDSessionInfoEntry .1.3.6.1.4.1.6296.101.11.10.3.1.1 |
sleBFDSessionInfoEntryDescription. SleBFDSessionInfoEntry .1.3.6.1.4.1.6296.101.11.10.3.1.1.1 |
sleBFDSessionNeighAddrTypeType of Neighbor Address referred to this sessionro InetAddressType (INET-ADDRESS-MIB) .1.3.6.1.4.1.6296.101.11.10.3.1.1.1.1 |
sleBFDSessionNeighAddrValueValue of Neighbor Address referred to this session.ro InetAddress (INET-ADDRESS-MIB) .1.3.6.1.4.1.6296.101.11.10.3.1.1.1.2 |
sleBFDSessionRegProtocolsValue of Neighbor Address referred to this session.ro Bits .1.3.6.1.4.1.6296.101.11.10.3.1.1.1.3 |
sleBFDSessionLocalDiscrDiscriminator of this session.ro Unsigned32 .1.3.6.1.4.1.6296.101.11.10.3.1.1.1.4 |
sleBFDSessionRemoteDiscrDiscriminator of remote session neighboring this session.ro Unsigned32 .1.3.6.1.4.1.6296.101.11.10.3.1.1.1.5 |
sleBFDSessionDetecMultiplierDetect Multiplier value which this session used. default: 3ro INTEGER .1.3.6.1.4.1.6296.101.11.10.3.1.1.1.6 |
sleBFDSessionStatusStatus of this session. AdminDown(0) is same as disabled(4).ro Enumeration .1.3.6.1.4.1.6296.101.11.10.3.1.1.1.7 |
sleBFDSessionEchoUsageDetermine whether this session use or not echo function.ro Enumeration .1.3.6.1.4.1.6296.101.11.10.3.1.1.1.8 |
sleBFDSessionUptimeThe time since this session's status changed into Up'.ro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.6296.101.11.10.3.1.1.1.9 |
sleBFDSessionStats OBJECT IDENTIFIER .1.3.6.1.4.1.6296.101.11.10.3.2 |
sleBFDSessionStatsTableDescription. SEQUENCE OF SleBFDSessionStatsEntry .1.3.6.1.4.1.6296.101.11.10.3.2.1 |
sleBFDSessionStatsEntryDescription. SleBFDSessionStatsEntry .1.3.6.1.4.1.6296.101.11.10.3.2.1.1 |
sleBFDSessionStatsHolddownTimeType of Neighbor Address referred to this session.ro Unsigned32 .1.3.6.1.4.1.6296.101.11.10.3.2.1.1.1 |
sleBFDSessionStatsHolddownExpiresThe time remaining before this entry change into down status without receiving hello in unit of milliseconds.ro Unsigned32 .1.3.6.1.4.1.6296.101.11.10.3.2.1.1.2 |
sleBFDSessionStatsHolddownHitCountHit Count whose this session status chang into down.ro Unsigned32 .1.3.6.1.4.1.6296.101.11.10.3.2.1.1.3 |
sleBFDSessionStatsHelloTimeThe time is when it expects next hello, after receiving that in unit of milliseconds.ro Unsigned32 .1.3.6.1.4.1.6296.101.11.10.3.2.1.1.4 |
sleBFDSessionStatsHelloHitCountHit Count whose this session received.ro Unsigned32 .1.3.6.1.4.1.6296.101.11.10.3.2.1.1.5 |
sleBFDSessionStatsRxCountHit Count whose this session received control packet.ro Unsigned32 .1.3.6.1.4.1.6296.101.11.10.3.2.1.1.6 |
sleBFDSessionStatsRxAvgIntervalAverage interval whose this session received control packet.ro Unsigned32 .1.3.6.1.4.1.6296.101.11.10.3.2.1.1.7 |
sleBFDSessionStatsRxMinIntervalMinimum interval whose this session received control packet.ro Unsigned32 .1.3.6.1.4.1.6296.101.11.10.3.2.1.1.8 |
sleBFDSessionStatsRxMaxIntervalMaximum interval whose this session received control packet.ro Unsigned32 .1.3.6.1.4.1.6296.101.11.10.3.2.1.1.9 |
sleBFDSessionStatsTxCountHit Count whose this session send control packet.ro Unsigned32 .1.3.6.1.4.1.6296.101.11.10.3.2.1.1.10 |
sleBFDSessionStatsTxAvgIntervalAverage interval whose this session sent control packet.ro Unsigned32 .1.3.6.1.4.1.6296.101.11.10.3.2.1.1.11 |
sleBFDSessionStatsTxMinIntervalMinimum interval whose this session sent control packet.ro Unsigned32 .1.3.6.1.4.1.6296.101.11.10.3.2.1.1.12 |
sleBFDSessionStatsTxMaxIntervalMaximum interval whose this session received control packet.ro Unsigned32 .1.3.6.1.4.1.6296.101.11.10.3.2.1.1.13 |
sleBFDSessionStatsEchoRxCountHit Count whose this session received echo packetro Unsigned32 .1.3.6.1.4.1.6296.101.11.10.3.2.1.1.14 |
sleBFDSessionStatsEchoRxAvgIntervalAverage interval whose this session received echo packetro Unsigned32 .1.3.6.1.4.1.6296.101.11.10.3.2.1.1.15 |
sleBFDSessionStatsEchoRxMinIntervalMinimum interval whose this session received echo packetro Unsigned32 .1.3.6.1.4.1.6296.101.11.10.3.2.1.1.16 |
sleBFDSessionStatsEchoRxMaxIntervalMaximum interval whose this session received echo packetro Unsigned32 .1.3.6.1.4.1.6296.101.11.10.3.2.1.1.17 |
sleBFDSessionStatsEchoTxCountHit Count whose this session send echo packetro Unsigned32 .1.3.6.1.4.1.6296.101.11.10.3.2.1.1.18 |
sleBFDSessionStatsEchoTxAvgIntervalAverage interval whose this session sent echo packet.ro Unsigned32 .1.3.6.1.4.1.6296.101.11.10.3.2.1.1.19 |
sleBFDSessionStatsEchoTxMinIntervaMinimum interval whose this session sent echo packet.ro Unsigned32 .1.3.6.1.4.1.6296.101.11.10.3.2.1.1.20 |
sleBFDSessionStatsEchoTxMaxIntervalMaximum interval whose this session received echo packet.ro Unsigned32 .1.3.6.1.4.1.6296.101.11.10.3.2.1.1.21 |
sleBFDSessionLocal OBJECT IDENTIFIER .1.3.6.1.4.1.6296.101.11.10.3.3 |
sleBFDSessionLocalTableDescription. SEQUENCE OF SleBFDSessionLocalEntry .1.3.6.1.4.1.6296.101.11.10.3.3.1 |
sleBFDSessionLocalEntryDescription. SleBFDSessionLocalEntry .1.3.6.1.4.1.6296.101.11.10.3.3.1.1 |
sleBFDSessionLocalDiagValue of State field of this session's control packet.ro Enumeration .1.3.6.1.4.1.6296.101.11.10.3.3.1.1.1 |
sleBFDSessionLocalStateValue of Diag field of this session's control packetro Enumeration .1.3.6.1.4.1.6296.101.11.10.3.3.1.1.2 |
sleBFDSessionLocalFlagsValue of Flags field of this session's control packet.ro Bits .1.3.6.1.4.1.6296.101.11.10.3.3.1.1.3 |
sleBFDSessionLocalMultiplierValue of MinTxInterval field of this session's control packet in unit of microseconds.ro INTEGER .1.3.6.1.4.1.6296.101.11.10.3.3.1.1.4 |
sleBFDSessionLocalMinTxIntervalValue of MinTxInterval field of this session's control packet in unit of microseconds.ro Unsigned32 .1.3.6.1.4.1.6296.101.11.10.3.3.1.1.5 |
sleBFDSessionLocalMinRxIntervalValue of MinRxInterval field of this session's control packet in unit of microseconds.ro Unsigned32 .1.3.6.1.4.1.6296.101.11.10.3.3.1.1.6 |
sleBFDSessionLocalMinEchoIntervalValue of MinEchoInterval field of this session's control packet in unit of microseconds.ro Unsigned32 .1.3.6.1.4.1.6296.101.11.10.3.3.1.1.7 |
sleBFDSessionRemote OBJECT IDENTIFIER .1.3.6.1.4.1.6296.101.11.10.3.4 |
sleBFDSessionRemoteTableDescription. SEQUENCE OF SleBFDSessionRemoteEntry .1.3.6.1.4.1.6296.101.11.10.3.4.1 |
sleBFDSessionRemoteEntryDescription. SleBFDSessionRemoteEntry .1.3.6.1.4.1.6296.101.11.10.3.4.1.1 |
sleBFDSessionRemoteDiagValue of State field of remote session's control packet.ro Enumeration .1.3.6.1.4.1.6296.101.11.10.3.4.1.1.1 |
sleBFDSessionRemoteStateValue of Diag field of remote session's control packetro Enumeration .1.3.6.1.4.1.6296.101.11.10.3.4.1.1.2 |
sleBFDSessionremoteFlagsValue of Flags field of remote session's control packet.ro Bits .1.3.6.1.4.1.6296.101.11.10.3.4.1.1.3 |
sleBFDSessionRemoteMultiplierValue of MinTxInterval field of this session's control packet in unit of microseconds.ro INTEGER .1.3.6.1.4.1.6296.101.11.10.3.4.1.1.4 |
sleBFDSessionRemoteMinTxIntervalValue of MinTxInterval field of remote session's control packet in unit of microseconds.ro Unsigned32 .1.3.6.1.4.1.6296.101.11.10.3.4.1.1.5 |
sleBFDSessionRemoteMinRxIntervalValue of MinRxInterval field of remote session's control packet in unit of microseconds.ro Unsigned32 .1.3.6.1.4.1.6296.101.11.10.3.4.1.1.6 |
sleBFDSessionRemoteMinEchoIntervalValue of MinEchoInterval field of remote session's control packet in unit of microseconds.ro Unsigned32 .1.3.6.1.4.1.6296.101.11.10.3.4.1.1.7 |
sleBFDStaticGw OBJECT IDENTIFIER .1.3.6.1.4.1.6296.101.11.10.4 |
sleBFDStaticGwTableDescription. SEQUENCE OF SleBFDStaticGwEntry .1.3.6.1.4.1.6296.101.11.10.4.1 |
sleBFDStaticGwEntryDescription. SleBFDStaticGwEntry .1.3.6.1.4.1.6296.101.11.10.4.1.1 |
sleBFDStaticGwAddrTypeThe BFD static Gateway address type. Only ipv4(1).rw InetAddressType (INET-ADDRESS-MIB) .1.3.6.1.4.1.6296.101.11.10.4.1.1.1 |
sleBFDStaticGwAddrThe BFD static Gateway address. 4bytesrw InetAddress (INET-ADDRESS-MIB) .1.3.6.1.4.1.6296.101.11.10.4.1.1.2 |
sleBFDStaticGwControl OBJECT IDENTIFIER .1.3.6.1.4.1.6296.101.11.10.4.2 |
sleBFDStaticGwControlRequestDescription.rw Enumeration .1.3.6.1.4.1.6296.101.11.10.4.2.1 |
sleBFDStaticGwControlStatusDescription.ro SleControlStatusType (SLE-TC-MIB) .1.3.6.1.4.1.6296.101.11.10.4.2.2 |
sleBFDStaticGwControlTimerDescription.rw Gauge32 .1.3.6.1.4.1.6296.101.11.10.4.2.3 |
sleBFDStaticGwControlTimeStampDescription.ro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.6296.101.11.10.4.2.4 |
sleBFDStaticGwControlReqResultDescription.ro SleControlRequestResultType (SLE-TC-MIB) .1.3.6.1.4.1.6296.101.11.10.4.2.5 |
sleBFDStaticGwControlNetIfIndexDescription.rw Integer32 .1.3.6.1.4.1.6296.101.11.10.4.2.6 |
sleBFDStaticGwControlGwAddrTypeDescription.rw InetAddressType (INET-ADDRESS-MIB) .1.3.6.1.4.1.6296.101.11.10.4.2.7 |
sleBFDStaticGwControlGwAddrDescription.rw InetAddress (INET-ADDRESS-MIB) .1.3.6.1.4.1.6296.101.11.10.4.2.8 |
sleBFDStaticGwNotification OBJECT IDENTIFIER .1.3.6.1.4.1.6296.101.11.10.4.3 |
sleBFDStaticGwAddedDescription. NOTIFICATION-TYPE .1.3.6.1.4.1.6296.101.11.10.4.3.1 |
sleBFDStaticGwDeletedDescription. NOTIFICATION-TYPE .1.3.6.1.4.1.6296.101.11.10.4.3.2 |
sleNetworkGroupDescription. Unknown .1.3.6.1.4.1.6296.101.11.14 |
sleNetworkNotificationGroupDescription. Unknown .1.3.6.1.4.1.6296.101.11.15 |