SLE-MPLS-TP-TUNNEL-MIB
Copyright (C) The Internet Society (2004). The initial version of this MIB module was published in RFC 3812. For full legal notices see the RFC itself or see: http://www.ietf.org/copyrights/ianamib.html This MIB module contains managed object definitions for MPLS Traffic Engineering (TE) as defined in: 1. Extensions to RSVP for LSP Tunnels, Awduche et al, RFC 3209, December 2001 2. Constraint-Based LSP Setup using LDP, Jamoussi (Editor), RFC 3212, January 2002 3. Requirements for Traffic Engineering Over MPLS, Awduche, D., Malcolm, J., Agogbua, J., O'Dell, M., and J. McManus, [RFC2702], September 1999
Main OID:
sleMplsTpTunnel.1.3.6.1.4.1.6296.101.16.14
68
Objects
Active
Status
7
Dependencies
Imported Objects
Objects
68 total| Object Name |
|---|
sleMplsSLE MPLS. OBJECT IDENTIFIER .1.3.6.1.4.1.6296.101.16 |
sleMplsTpTunnelCopyright (C) The Internet Society (2004). The initial version of this MIB module was published in RFC 3812. For full legal notices see the RFC itself or see: http://www.ietf.org/copyrights/ianamib.html This MIB module contains managed object definitions for MPLS Traffic Engineering (TE) as defined in: 1. Extensions to RSVP for LSP Tunnels, Awduche et al, RFC 3209, December 2001 2. Constraint-Based LSP Setup using LDP, Jamoussi (Editor), RFC 3212, January 2002 3. Requirements for Traffic Engineering Over MPLS, Awduche, D., Malcolm, J., Agogbua, J., O'Dell, M., and J. McManus, [RFC2702], September 1999 MODULE-IDENTITY .1.3.6.1.4.1.6296.101.16.14 |
sleMplsTpTunnelCfg OBJECT IDENTIFIER .1.3.6.1.4.1.6296.101.16.14.1 |
sleMplsTpTunnelCfgInfoTableThe mplsTunnelTable allows new MPLS tunnels to be created between an LSR and a remote endpoint, and existing tunnels to be reconfigured or removed. Note that only point-to-point tunnel segments are supported, although multipoint-to-point and point- to-multipoint connections are supported by an LSR acting as a cross-connect. Each MPLS tunnel can thus have one out-segment originating at this LSR and/or one in-segment terminating at this LSR. SEQUENCE OF SleMplsTpTunnelCfgInfoEntry .1.3.6.1.4.1.6296.101.16.14.1.1 |
sleMplsTpTunnelCfgInfoEntryAn entry in this table represents an MPLS tunnel. An entry can be created by a network administrator or by an SNMP agent as instructed by an MPLS signalling protocol. Whenever a new entry is created with mplsTunnelIsIf set to true(1), then a corresponding entry is created in ifTable as well (see RFC 2863). The ifType of this entry is mplsTunnel(150). A tunnel entry needs to be uniquely identified across a MPLS network. Indices mplsTunnelIndex and mplsTunnelInstance uniquely identify a tunnel on the LSR originating the tunnel. To uniquely identify a tunnel across an MPLS network requires index mplsTunnelIngressLSRId. The last index mplsTunnelEgressLSRId is useful in identifying all instances of a tunnel that terminate on the same egress LSR. SleMplsTpTunnelCfgInfoEntry .1.3.6.1.4.1.6296.101.16.14.1.1.1 |
sleMplsTpTunnelCfgInfoIndexA unique value which identify an entry in this table. Unsigned32 .1.3.6.1.4.1.6296.101.16.14.1.1.1.1 |
sleMplsTpTunnelCfgInfoNameThe canonical name assigned to the tunnel. This name can be used to refer to the tunnel on the LSR's console port. If mplsTunnelIsIf is set to true then the ifName of the interface corresponding to this tunnel should have a value equal to mplsTunnelName. Also see the description of ifName in RFC 2863.ro OCTET STRING .1.3.6.1.4.1.6296.101.16.14.1.1.1.2 |
sleMplsTpTunnelCfgInfoIdUniquely identifies a set of tunnel instances between a pair of ingress and egress LSRs. Managers should obtain new values for row creation in this table by reading mplsTunnelIndexNext. When the MPLS signalling protocol is rsvp(2) this value SHOULD be equal to the value signaled in the Tunnel Id of the Session object. When the MPLS signalling protocol is crldp(3) this value SHOULD be equal to the value signaled in the LSP ID.ro Unsigned32 .1.3.6.1.4.1.6296.101.16.14.1.1.1.3 |
sleMplsTpTunnelCfgInfoSrcIdTypeThis object is used to set the ietf or itut type.ro Enumeration .1.3.6.1.4.1.6296.101.16.14.1.1.1.4 |
sleMplsTpTunnelCfgInfoSrcGIdThis Object is used to display the GlobalID of IETFro Unsigned32 .1.3.6.1.4.1.6296.101.16.14.1.1.1.5 |
sleMplsTpTunnelCfgInfoSrcCcThis Object is used to display the Source CC-ID of ITUTro MplsCcId (MPLS-TC-EXT-STD-MIB) .1.3.6.1.4.1.6296.101.16.14.1.1.1.6 |
sleMplsTpTunnelCfgInfoSrcIccThis Object is used to set the Source ICC-ID of ITUTro MplsIccId (MPLS-TC-EXT-STD-MIB) .1.3.6.1.4.1.6296.101.16.14.1.1.1.7 |
sleMplsTpTunnelCfgInfoSrcNodeIdThis Object is used to display the Source Node ID of IETF and ITUTro IpAddress .1.3.6.1.4.1.6296.101.16.14.1.1.1.8 |
sleMplsTpTunnelCfgInfoDestIdTypeThis object is used to set the ietf or itut type.ro Enumeration .1.3.6.1.4.1.6296.101.16.14.1.1.1.9 |
sleMplsTpTunnelCfgInfoDestGIdThis Object is used to set the Destination GlobalID of IETFro Unsigned32 .1.3.6.1.4.1.6296.101.16.14.1.1.1.10 |
sleMplsTpTunnelCfgInfoDestCcThis Object is used to display the Destination CC-ID of ITUTro MplsCcId (MPLS-TC-EXT-STD-MIB) .1.3.6.1.4.1.6296.101.16.14.1.1.1.11 |
sleMplsTpTunnelCfgInfoDestIccThis Object is used to set the Destination ICC-ID of ITUTro MplsIccId (MPLS-TC-EXT-STD-MIB) .1.3.6.1.4.1.6296.101.16.14.1.1.1.12 |
sleMplsTpTunnelCfgInfoDestNodeIdThis Object is used to display the Destination Node ID of IETF and ITUTro IpAddress .1.3.6.1.4.1.6296.101.16.14.1.1.1.13 |
sleMplsTpTunnelCfgInfoModeThis object is used to set the Tunnel Modero Enumeration .1.3.6.1.4.1.6296.101.16.14.1.1.1.14 |
sleMplsTpTunnelCfgInfoFwdInLabelThis object is used to display the Forward In Label. The lable range is 0 to 1048575. Here 0 to 15 are reserved labels. User allowed range is 16 to 1048575.. The default value 1048576 is invalid labelro MplsLabel (MPLS-TC-STD-MIB) .1.3.6.1.4.1.6296.101.16.14.1.1.1.15 |
sleMplsTpTunnelCfgInfoFwdInIfIndexThis object is used to set the Forward IN Interface indexro InterfaceIndexOrZero (IF-MIB) .1.3.6.1.4.1.6296.101.16.14.1.1.1.16 |
sleMplsTpTunnelCfgInfoFwdOperationThis object is used to set the Forward Ilm OPeration .ro Enumeration .1.3.6.1.4.1.6296.101.16.14.1.1.1.17 |
sleMplsTpTunnelCfgInfoFwdOutLabelThis object is used to display the Forward In Label. The lable range is 0 to 1048575. Here 0 to 15 are reserved labels. User allowed range is 16 to 1048575. The default value 1048576 is invalid labelro MplsLabel (MPLS-TC-STD-MIB) .1.3.6.1.4.1.6296.101.16.14.1.1.1.18 |
sleMplsTpTunnelCfgInfoFwdOutIfIndexThis object is used to set the Forward OUT Interface indexro InterfaceIndexOrZero (IF-MIB) .1.3.6.1.4.1.6296.101.16.14.1.1.1.19 |
sleMplsTpTunnelCfgInfoFwdOutMacThis object is used to display the Forward OUT MAC ADDRESSro MacAddress (SNMPv2-TC) .1.3.6.1.4.1.6296.101.16.14.1.1.1.20 |
sleMplsTpTunnelCfgInfoRevInLabelThis object is used to display the Forward In Label. The lable range is 0 to 1048575. Here 0 to 15 are reserved labels. User allowed range is 16 to 1048575. The default value 1048576 is invalid labelro MplsLabel (MPLS-TC-STD-MIB) .1.3.6.1.4.1.6296.101.16.14.1.1.1.21 |
sleMplsTpTunnelCfgInfoRevInIfIndexThis object is used to set the Reverse IN Interface indexro InterfaceIndexOrZero (IF-MIB) .1.3.6.1.4.1.6296.101.16.14.1.1.1.22 |
sleMplsTpTunnelCfgInfoRevOperationThis object is used to set the Reverse Ilm OPeration .ro Enumeration .1.3.6.1.4.1.6296.101.16.14.1.1.1.23 |
sleMplsTpTunnelCfgInfoRevOutLabelThis object is used to display the Forward In Label. The lable range is 0 to 1048575. Here 0 to 15 are reserved labels. User allowed range is 16 to 1048575. The default value 1048576 is invalid labelro MplsLabel (MPLS-TC-STD-MIB) .1.3.6.1.4.1.6296.101.16.14.1.1.1.24 |
sleMplsTpTunnelCfgInfoRevOutIfIndexThis object is used to set the Reverse OUT Interface indexro InterfaceIndexOrZero (IF-MIB) .1.3.6.1.4.1.6296.101.16.14.1.1.1.25 |
sleMplsTpTunnelCfgInfoRevOutMacThis object is used to display the Forward OUT MAC ADDRESS .ro MacAddress (SNMPv2-TC) .1.3.6.1.4.1.6296.101.16.14.1.1.1.26 |
sleMplsTpTunnelCfgInfoStateThis object is to display status of the tunnel.ro Enumeration .1.3.6.1.4.1.6296.101.16.14.1.1.1.27 |
sleMplsTpTunnelCfgInfoRoleThis object is to display Role of the tunnel.ro Enumeration .1.3.6.1.4.1.6296.101.16.14.1.1.1.28 |
sleMplsTpTunnelCfgInfoAssociateTnlNameThis object to display associate of reverse tunnel.ro OCTET STRING .1.3.6.1.4.1.6296.101.16.14.1.1.1.29 |
sleMplsTpTunnelCfgInfoDescriptionDescription.ro OCTET STRING .1.3.6.1.4.1.6296.101.16.14.1.1.1.30 |
sleMplsTpTunnelCfgInfoHlspRoleThis object is used to set the Hlsp Tunnel. whether the tunnel is Server or client. server (1) :- To set the Server Tunnel client(2) :- To set the Client Tunnel .ro Enumeration .1.3.6.1.4.1.6296.101.16.14.1.1.1.31 |
sleMplsTpTunnelCfgInfoHlspServerTunnelNameThis object is used to set the server TunnelName, when sleMplsTpTunnelCfgControlHlspOption as a client .ro OCTET STRING .1.3.6.1.4.1.6296.101.16.14.1.1.1.32 |
sleMplsTpTunnelCfgInfoQosPolicyNameThis object is used to set the Qos Policy name.ro OCTET STRING .1.3.6.1.4.1.6296.101.16.14.1.1.1.33 |
sleMplsTpTunnelCfgControl OBJECT IDENTIFIER .1.3.6.1.4.1.6296.101.16.14.1.2 |
sleMplsTpTunnelCfgControlRequestThis object holds the possible read-write columns that can be modified in the Tunnel table. For each read-write column of Tunnel table, a Set Operation controlvalue is added in this object.rw Enumeration .1.3.6.1.4.1.6296.101.16.14.1.2.1 |
sleMplsTpTunnelCfgControlStatusThis object displays the status of the configuration done.ro SleControlStatusType (SLE-TC-MIB) .1.3.6.1.4.1.6296.101.16.14.1.2.2 |
sleMplsTpTunnelCfgControlTimerThis object is based on the SLE style where a timer is configured for every control table.rw Gauge32 .1.3.6.1.4.1.6296.101.16.14.1.2.3 |
sleMplsTpTunnelCfgControlTimeStampThis object specifies the time at which the configuration is done.ro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.6296.101.16.14.1.2.4 |
sleMplsTpTunnelCfgControlReqResultThe standard result of the SET operation is stored here.ro SleControlRequestResultType (SLE-TC-MIB) .1.3.6.1.4.1.6296.101.16.14.1.2.5 |
sleMplsTpTunnelCfgControlNameThe canonical name assigned to the tunnel. This name can be used to refer to the tunnel on the LSR's console port. If mplsTunnelIsIf is set to true then the ifName of the interface corresponding to this tunnel should have a value equal to SlemplsTunnelName. Also see the description of ifName in RFC 2863.rw OCTET STRING .1.3.6.1.4.1.6296.101.16.14.1.2.6 |
sleMplsTpTunnelCfgControlIdThis object is used to set the tunnel Id .rw Unsigned32 .1.3.6.1.4.1.6296.101.16.14.1.2.7 |
sleMplsTpTunnelCfgControlSrcIdTypeThis object is used to set the ietf or itut type.rw Enumeration .1.3.6.1.4.1.6296.101.16.14.1.2.8 |
sleMplsTpTunnelCfgControlSrcGIdThis object is used to set the source Global-Id for IETF .rw Unsigned32 .1.3.6.1.4.1.6296.101.16.14.1.2.9 |
sleMplsTpTunnelCfgControlSrcCcThis object is used to set the source CC-ID for ITUT.rw MplsCcId (MPLS-TC-EXT-STD-MIB) .1.3.6.1.4.1.6296.101.16.14.1.2.10 |
sleMplsTpTunnelCfgControlSrcIccThis object is used to set the Source ICC-ID for ITUT.rw MplsIccId (MPLS-TC-EXT-STD-MIB) .1.3.6.1.4.1.6296.101.16.14.1.2.11 |
sleMplsTpTunnelCfgControlSrcNodeIdThis object is used to set the Source Node-Id for IETF and ITUTrw IpAddress .1.3.6.1.4.1.6296.101.16.14.1.2.12 |
sleMplsTpTunnelCfgControlDestIdTypeThis object is used to set the ietf or itut type.rw Enumeration .1.3.6.1.4.1.6296.101.16.14.1.2.13 |
sleMplsTpTunnelCfgControlDestGIdThis object is used to set the Destination Global-Id for IETF .rw Unsigned32 (1) .1.3.6.1.4.1.6296.101.16.14.1.2.14 |
sleMplsTpTunnelCfgControlDestCcThis object is used to set the Destination CC-ID for ITUT.rw MplsCcId (MPLS-TC-EXT-STD-MIB) .1.3.6.1.4.1.6296.101.16.14.1.2.15 |
sleMplsTpTunnelCfgControlDestIccThis object is used to set the Destination ICC-ID for ITUT.rw MplsIccId (MPLS-TC-EXT-STD-MIB) .1.3.6.1.4.1.6296.101.16.14.1.2.16 |
sleMplsTpTunnelCfgControlDestNodeIdThis object is used to set the Destination NodeID for IETF and ITUT.rw IpAddress .1.3.6.1.4.1.6296.101.16.14.1.2.17 |
sleMplsTpTunnelCfgControlModeThis object is used to set the Tunnel mode .rw Enumeration .1.3.6.1.4.1.6296.101.16.14.1.2.18 |
sleMplsTpTunnelCfgControlPathThis object is used to Set the forward path and reverse path tunnel.rw Enumeration .1.3.6.1.4.1.6296.101.16.14.1.2.19 |
sleMplsTpTunnelCfgControlInLabelThis object is used to set the Inlabel.rw MplsLabel (MPLS-TC-STD-MIB) .1.3.6.1.4.1.6296.101.16.14.1.2.20 |
sleMplsTpTunnelCfgControlInInterfaceThis object is used to set the Ininterface index.rw InterfaceIndexOrZero (IF-MIB) .1.3.6.1.4.1.6296.101.16.14.1.2.21 |
sleMplsTpTunnelCfgControlOperationThis object is used to set the operation of Tuunelrw Enumeration .1.3.6.1.4.1.6296.101.16.14.1.2.22 |
sleMplsTpTunnelCfgControlOutLabelThis object is used to set the outlabel.rw MplsLabel (MPLS-TC-STD-MIB) .1.3.6.1.4.1.6296.101.16.14.1.2.23 |
sleMplsTpTunnelCfgControlOutInterfaceThis object is used to set the outerinterface index.rw InterfaceIndexOrZero (IF-MIB) .1.3.6.1.4.1.6296.101.16.14.1.2.24 |
sleMplsTpTunnelCfgControlOutMacAddressThis object is used to Set the Out MacAddress .rw MacAddress (SNMPv2-TC) .1.3.6.1.4.1.6296.101.16.14.1.2.25 |
sleMplsTpTunnelCfgControlAssociateTnlNameThis object is used to Associated Forward tunnel and reverse tunnel with reverse tunnel name .rw OCTET STRING .1.3.6.1.4.1.6296.101.16.14.1.2.26 |
sleMplsTpTunnelCfgControlDescriptionDescription.rw OCTET STRING .1.3.6.1.4.1.6296.101.16.14.1.2.27 |
sleMplsTpTunnelCfgControlHlspSeverTunnelNameThis object is used to set the server Tunnel name for associating server and client.rw OCTET STRING .1.3.6.1.4.1.6296.101.16.14.1.2.28 |
sleMplsTpTunnelCfgControlQosPolicyNameThis object is used to set the Qos Policy name.rw OCTET STRING .1.3.6.1.4.1.6296.101.16.14.1.2.29 |